Home

Juicer #58 Operating Instructions

1. does nor apply to damage resulting from an installation or use which does not comply with the instructions supplied with each appliance user manual or in the event of an obvious lack of maintenance or non observance of basic electrical safety rules All part replacements under warranty are made after return of the defective part to our workshops carriage paid accompanied by a copy of this warranty certificate on which the serial number of the appliance is shown All appliances have an identification plate bearing a serial number identical to that on this warranty certificate In the event of serious damage which is deemed only to be repairable in our workshops and after agreement from our services all appliances under warranty are to be dispatched by the client carriage paid If the appliance is repaired outside the warranty the forwarding and return transport is the responsibility of the client Parts and labour are invoiced at the prices in force Spare parts price hourly labour cost All repairs will be subject to a prior estimate which should be agreed before repair In the event of a dispute the Courts for the manufacturer s area Lyon alone have jurisdiction APPLIANCE IDENTIFICATION PLATE SPECIMEN For all documents not supplied with the appliance I Printed Faxed and Downloaded
2. page of this manual e l the power cable 10 is damaged it should be replaced by a special assembly available from approved SANTOS dealers or from SANTOS USING FOR THE 1st TIME Remove the plunger 3 Rotate the clamping handle 1 by one half turn to release the cover 2 Fig 2 To be able to remove the cover turn then lift the cover 2 Fig 3 Model 28 Using the basket locking spanner 18 unscrew the basket fixing screw 15 completely while holding the basket immobile with the other hand Fig 4 Raise the bowl 4 The basket 5 should come out of its seating Fig 5 Remove the basket assembly 5 and wash in clean water Wash all the elements in contact with food in clean water the plunger 3 the cover 2 the bowl 4 and the pulp container 6 Fig 6 ee eS Installing the product discharge channel 1 Place the discharge channel 16 on the bowl 4 Insert and screw tight the 2 screws 17 on the bowl pins 4 Fig 7 RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE This equipment is marked with the selective sorting symbol relating to wastes from electrical and electronic equipment It signifies that this product should be taken over by a selective collection system conforming to the Guideline 2002 96 EC WEEE part Professional Equipment so that it can be either recycled or dismantled in order to reduce any impact on the environment For more information please contact your Retailer o
3. CE 8 MOTOR OVERLOAD GAFETIVEEATURE nenne nnennennn 8 MOTOR OVERHEATING GAFEIVEEATURE 9 SAFE ACCESS TO THE TOOL Starts ea an 9 WC HS Se ee ee eee ee eee en 9 NON E 10 FAGET EINEN ee 11 The machine will not start 11 The machine stops because the motor has overheated 11 The machine stops because Of an overload 2u02240002400 nenne nenne nenne nenne nenne nennen 11 The machine vibrates when running empty 11 REFERENCE TO STANDARDS zes ee eek 12 TESHAINIERE SPELIFIEATIONS ae ee ger cee ec 12 ELECTRICAL WIRING DIAGRAMS nenne onenne nenne nnennennn 13 Electrical wiring diagram 110 120V 50 60Hz nennen 13 Electrical wiring diagram 220 240V 50 60Hz oocccoccccnccnconcnccncncnncncnncncnncnonnrnonnnnconcnonnnns 14 SEITEN 16 EC HE E OR e AN Eos nee 19 CE COMPLIANCE DECLARATION THE MANUFACTURER SANTOS SAS 140 150 Av Roger SALENGRO 69120 VAULX EN VELIN LYON FRANCE HEREBY DECLARES THAT THE MACHINE DESIGNATED ON THE IDENTIFICATION PLATE AFFIXED e UNDER THE APPLIANCE e ON THE WARRANTY CERTIFICATE ON THE LAST PAGE OF THIS MANUAL COMPLIES WITH THE PROVISIONS OF THE machines DIRECTIVE AS MODIFIED Directive 98 37 CEl AND THE NATIONAL LEGISLATION TRANSPOSING IT IT ALSO COMPLIES WITH THE PROVISIONS OF THE FOLLOWING EUROPEAN DIRECTIVES No 73 23 dated 19 02 73 Low voltage directive No 89 336 CEM directive No 2002 95 CE RoHS directive
4. No 2002 96 CE WEEE directive The machine complies with the provisions of the following harmonised European standards EN ISO 12100 1 and 2 2004 Machine safety devices General design principles NF EN 60204 1 2006 Machine safety devices Machine electrical equipment General regulations NF EN 1678 1998 Machines for food products vegetable slicers NF EN 12547 1998 Juice extractor Common safety instructions SIGNED IN VAULX EN VELIN ON 01 05 2007 SIGNATORY S TITLE CHIEF EXECUTIVE OFFICER SIGNATORY S NAME JACQUES FOUQUET SIGNATURE IMPORTANT SAFEGUARDS When using cleaning or maintaining the machine always follow these instructions Read all instructions Note You will find it easier to understand the next few paragraphs if you refer to the diagrams at the end of this manual INSTALLATION AND HANDLING CAREFUL For all handling operations including unpacking the machine the cover clamping handle 1 must not be used for holding or lifting the appliance The machine can be handled by a single person It is recommended that the appliance be placed on a table or worktop for more comfortable use so that the juice outlet spout and the On 11 and Off 12 buttons are in front of you recommended height 90 cm to be adapted as required for the user During cleaning and installation handle the basket assembly 5 carefully so as not to put it out of shape thus preventing the machine from working prope
5. SANTOS SAS 140 150 AVENUE ROGER SALENGRO 69120 VAULX EN VELIN LYON FRANCE PHONE 33 0 472 37 35 29 FAX 33 0 478 26 58 21 FAX 33 0 478 26 58 21 we SANTOS E Mail santos santos fr www santos fr JUICE EXTRACTOR Model 28 58 USER AND MAINTENANCE MANUAL IMPORTANT documents included in this manual to be kept e CE COMPLIANCE DECLARATION e WARRANTY CERTIFICATE Model 28 Model 58 Coffee grinders Fruit juicers Mixers Blenders Drinks dispensers Planetary mixers Kneaders Cheese graters Ice crushers Mincers Vegetable slicers Dough mixer Moulins a caf Presse fruits Mixers Blenders Distributeurs de boissons Batteurs m langeurs P trin R pes a fromage Broyeurs a glacons Hache viande Coupe l gumes MODELES DEPOSES FRANCE ET INTERNATIONAL INTERNATIONALLY PATENTED MODELS MM CONTENTS CE COMPLIANCE DECLARATION ooocccnccnnnnccnncnncncncncnnnnncnononcnonnncnnoncnnnnnnnnnnnnnonnnnnenoneness Ile NR HE EE RE INSTALLATION AND Eege IMPROPER USE orere E E E E ee ee ee EEESTRISGALBONNECEION ee ee es 5 USING FOR THE Ier TIME nenne nnnnnnnnn 5 RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE 5 JUICE EXTRACTOR model 28 amp 58 6 USING EHEAPPLIANGE E 7 GIN KEE 7 HOW TO OUOP TRE MACHINE EE 7 CE sea seeaeaeaseeasane 7 PIECAUNONSSANd E E A AA E P A E 8 SAFETY MAINTENANCE iii ineeseeneeseenereeneeeenenneee 8 COVER AND BOWL PRESENCE SAFETY DEMI
6. e machine stopped The machine will not start e Check the mains power supply and the condition of the power supply cord e Check the position of the juice bowl 4 on the bowl centering device 7 the position of the cover 2 on the juice bowl and the locking of the clamping handle 1 The machine stops because the motor has overheated the metal casing around the motor unit is hot Remove the plug from the power supply socket and follow the instructions in the section on motor overheating safety feature The machine stops because of an overload see the section on motor overload safety feature The machine vibrates when running empty This vibration is caused by an imbalance This imbalance may be caused by e The basket 5 being positioned incorrectly check it is correctly positioned e Distortion of the basket 5 check and replace if necessary e SANTOS j REFERENCE TO STANDARDS CE Europe GS Germany checked by the LNE National Test Laboratory UL USA and cUL Canada NSF USA TECHNICAL SPECIFICATIONS Mains power supply Power supply voltage V 220 240 100 120 Frequency Hz 50 60 50 60 Start capacitor uF 80uF 260V 180uF 160V 8 15 Overload safety device A Start relay SANTOS reference 28505 58505 28505B 58505B Model 28 Model 58 Dating IL 28 30 0313 Noise LAeg dB Measured at 3000 rom 75 75 ref 20uPa Dimensions and weight Height mm Mode
7. l 28 Model 58 Width mm 465 Depth mm 330 Net weight kg Packaged weight kg Container capacity Liters Bowl spout height mm Temperature of products processed Min 4 C Max 120 C ELECTRICAL WIRING DIAGRAMS Electrical wiring diagram 110 120V 50 60Hz Bowl tightening safety device white white 7 Off Overload safety device Green Yellow pe ome Electrical wiring diagram 220 240V 50 60Hz White White ae White gt gt y Red White White Capacitor Blue White Starter relay Black White Violet tightening safety deyice m White NJ White Overload safety White TU device Green Yellow A A Tr M A TABLEAU DE TRADUCTION DES ELEMENTS DE LA MACHINE 1 6 8 Clamping handle Poignee de serrage 9 Clampingrod Tige de serrage 12 Stop button Bouton poussoir Arr t Ecrou de cuve Basket cleaning brush Brosse de nettoyage du panier FIGURES Figure 2 Figure 3 Figure 6 Figure 7 Figure 9 Figure 12 e Q santos d WARRANTY CERTIFICATE WARRANTY This appliance is guaranteed for twelve months from the date of manufacture appearing on the identification plate The guarantee is strictly limited to the free replacement of any original part acknowledged by us as being defective as a result of a fault or a manufacturing defect and identified as belonging to the appliance in question lt
8. lace parts subject to wear such as the grater the basket electrical or other components please refer to the parts list see the exploded A view at the end of this manual or that can be downloaded from our Web site www santos fr For the machine to operate properly it is recommended that a check is also made that the locking membrane 21 is in good condition in particular the absence of any signs of tearing Also check that the elastomer drive sprockets 22 are in good condition in particular the absence of any signs of wrenching For all spare part orders see references in the exploded view at the end of the manual state the type the appliance serial number and the electrical specifications recorded under the appliance SERVICING Neither a hose nor a pressure hose should be used for cleaning e After use clean the basket assembly bowl cover pulp container plunger in clean water or with a dish washing detergent product designed for this purpose Then rinse and dry Do not use abrasive products or pads to clean the basket assembly e The base is to be cleaned with a soft damp sponge then dried TAKE CARE For easier cleaning do not leave food remains to dry on the bowl 4 the basket assembly 5 the cover 2 or the fruit plunger 3 It is recommended that all these parts of the machine are cleaned immediately after the work is finished QS santos d FAULT FINDING First identify exactly why th
9. n products are liable to clog or block the sieve holes in which case the basket assembly 5 should be cleaned more frequently SAFETY MAINTENANCE COVER AND BOWL PRESENCE SAFETY DEVICE For the juice extractor to be able to start the cover 2 and the bowl 4 must be centered in position on the bowl centering device 7 and held by the clamping handle 1 Putting the clamping handle in the vertical position up without the bowl or without the cover means that the machine cannot be started MOTOR OVERLOAD SAFETY FEATURE Models 220 240V 50 60Hz Should the motor become blocked foreign body object that is too hard too much pressure with the fruit plunger on the products being processed the circuit breaker 14 located under the appliance triggers and cuts off the power supply to the motor Fig 13 Correct the fault reset the circuit breaker and re start the machine lf the problem persists switch off the power supply to the machine unplug the cord from the mains socket 10 and call in the maintenance service or contact a SANTOS approved dealer A e SANTOS Models 110 120V 50 60Hz Should the motor become blocked foreign body object that is too hard too much pressure with the fruit plunger on the products being processed the motor overheating safety feature triggers and switches off the motor see overheating safety feature MOTOR OVERHEATING SAFETY FEATURE Models 110 120V 50 60Hz only In the event of
10. n the bowl 4 making sure it is correctly located on the motor shaft 8 The drive pin 19 needs to be in the grooves in the basket assembly 5 Fig 9 Model 58 Place the basket assembly 5 in the bowl 4 making sure it is correctly located on the motor shaft 20 The drive pin 22 should enter the notches of the basket assembly 5 Fig 9 3 Model 28 Using the spanner 18 insert the basket locking screw 15 and screw it tight During this operation the basket shifts downwards a few millimeters During the locking operation the basket can be held with one hand 4 Place the cover 2 on the bowl 4 turn the cover to engage the 2 lugs in the catches on the locking rods Fig 10 5 Rotate the clamping handle 1 by one half turn to block and lock the cover in place 2 Fig d 6 Place the fruit plunger 3 in the cover feed channel 2 Fig 11 7 Position the pulp container 6 correctly relative to the outlet of the discharge channel 16 8 Connect the supply cord plug 10 to your mains supply socket Fig 12 9 Withdraw the fruit plunger 3 from the cover feed channel 2 Using 1 Start the machine by operating the On button 11 2 Place the recipient under the bowl spout 4 3 Introduce the fruits or vegetables into the cover feed channel 2 and push them onto the rotating grater with the fruit plunger 3 4 Continue this operation until the juice recipient is full or all the fruit and vegetables to be proce
11. r the SANTOS For eliminating or recycling components of equipment please contact a specialized company or contact SANTOS A The electronic products not undergoing a selective sorting are potentially dangerous for the environment The damaging materials should be eliminated or recycled according to the regulations in force JUICE EXTRACTOR model 28 amp 58 e Robust and very well constructed components made of cast aluminum engineered plastic and 18 10 stainless steel plate this juice extractor is particularly suitable for extracting juice and making coulis and sauce juices from fruits or vegetables used by the professionals in Restaurants Pizzerias Snack Bars Fast Food Outlets Special Theme Restaurants etc e lt has a powerful motor which drives a centrifugation basket e Centrifugation basket The active filtering part of the basket is made of stainless steel Model 58 the bottom part of the basket providing the drive and the locking system is made of food quality engineered plastic e 18 10 press drawn stainless steel bowl with stainless steel spout for collecting and funneling the product juices USING THE APPLIANCE USING Assembly and preparation 1 Fit the bowl 4 on the bowl centering device 7 making sure that the juice run off spout is located in the indent provided for that purpose in the bowl centering device 7 Fig 8 2 Model 28 Place the basket assembly 5 i
12. rly IMPROPER USE e Do not place food in the channel and press with the plunger before you have started the machine e The appliance is not designed for handling frozen foods e Remove stones from fruit before processing it in the machine e g mangoes apricots peaches Do not let the stones go into the machine Neither a hose nor a pressure hose should be used for cleaning The machine must not be left to operate without supervision Do not use abrasive sponge for cleaning the basket The appliance must not be used on any surface which has a slope of more than 10 relative to horizontal The machine s 4 feet must always be resting on that surface The machine s motor spindle must always be vertical relative to that surface e Use of spare parts other than certified original SANTOS parts is prohibited y The appliance is available in with a choice of two voltages for the power supply e 220 240V 50 60 Hz single phase e 100V 50 Hz 120V 60 Hz single phase Line protection the appliance should be connected to a standard 2 pole earth electric socket The installation should be fitted with an RCD and a fuse rated at 16A The appliance must be earthed ELECTRICAL CONNECTION CARE e Before connecting the machine check that the mains electrical voltage is the same as the voltage for your appliance Its value is shown gt either on the identification plate under the machine gt oron the identification plate on the last
13. ssed have been used Also keep an eye on the level of pulp in the pulp container 6 HOW TO STOP THE MACHINE The appliance is stopped 1 by pushing the Off button 12 2 or by turning the clamping handle 1 from the back to the front 3 or by unplugging the mains cord plug 10 Cleaning A Handle the basket assembly 5 carefully so as not to put it out of shape thus preventing the machine from working properly To clean the basket assembly 5 it is recommended to use the brush 25 supplied with the machine for proper cleaning of filter sieve holes and the grater teeth Fig 15 Do not use abrasive sponge for cleaning the basket Cleaning will be easier if you do not wait for the food remains to dry in the bowl basket and cover Precautions and risks During preparation the level in the pulp container 6 should be monitored to prevent the cover pulp outlet 2 from clogging Such clogging could result in an imbalance in the basket assembly 5 and thus a risk of damaging the machine The quantity of products to be processed before reaching the maximum filling level in the container 6 varies according to the products being processed lf during preparation an imbalance should occur well before the pulp container is full it is sometimes appropriate to continue adding food for the imbalance to be cleared But if the imbalance continues the machine must be stopped and the basket assembly 5 cleaned Certai
14. the motor overheating the appliance stops automatically The safety feature has an automatic reset so wait for the motor to cool 15 to 30 minutes before restarting the machine lf the problem persists switch off the power supply to the machine unplug the cord from the mains socket 10 and call in the maintenance service or contact a SANTOS approved dealer SAFE ACCESS TO THE TOOLS The juice extractor can only be started if the cover and bowl are positioned correctly on the bowl centering device 7 and the clamping handle 1 is locked Releasing the clamping handle 1 results in the machine stopping and the immobilization of the rotating elements in less than 3 seconds Re starting the juice extractor requires specific operation of the On switch 11 again A cut in the mains power supply makes the machine stop MAINTENANCE Before carrying out any work on the juice extractor the machine must in all cases be unplugged from the mains power supply and the motor start capacitor discharged Discharging the capacitor Use a screwdriver with insulated handle to touch the 2 connectors on the capacitor 13 The appearance of an electric arc shows that the capacitor has discharged Fig 14 Spare Parts IMPORTANT Use of spare parts other than certified original SANTOS parts is prohibited This machine requires no particular maintenance because the bearings are lubricated for life lf any intervention is necessary to rep

Juicer #58 Operating Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents