User manual Washing Machine ZWN 7100 L ZWN 7120 L
Contents
1. Delayed start The Selected delay set by pressing the rele vant button appears on the display for a few seconds then the duration of the selected programme is displayed again The delay time value decreases by one unit every hour and then when 1 hour remains every minute Alarm codes In the event of operating problems some alarm codes can be displayed for example EZ see paragraph What to do if Incorrect option selection If an option which is not compatible with the set wash programme is selected the mes sage Err is displayed at the bottom of the display for a few seconds The integrated red light of button 7 starts flashing End of programme When the programme has finished the flash ing zero 7 is displayed The pilot light 9 and the pilot light of button 7 go out The door can be opened in order to activate the ECO valve Then run a cotton cycle at the highest temper ature without any laundry in the machine to remove any manufacturing residue from the drum and tub Pour 1 2 a measure of detergent into the main wash compartment and start the machine Child safety lock This device permits you to leave the appliance unattended so you do not need to worry that children might be injured by or cause damage to the appliance This function remains enabled al so when the washing machine is not working There are two different ways to set this option 1 Before pressing button 7 it will be impossi2. On the following page there is a picture of the control panel lt shows the programme selector dial as well as the buttons pilot lights and the display These are presented by relevant num bers on the following pages Aa 00000 o GE zz DE o 000 O Programme selector dial SPIN reduction button OPTIONS button PREWASH button EASY IRON button Table of symbols Spin reduction ti G EXTRA RINSE button START PAUSE button G DELAY START button O DOOR LOCKED pilot light Display Prewash www zanussi com cj Rinse Hold 4 Cc Options O Super Quick gt Il lt Economy A Child lock G Easy Iron Extra Rinse Start Pause Door locked Delay Start Programme selector dial spin speed button and available options Programme Selector Dial It allows you to switch the appliance on off and or to select a programme Spin Reduction By pressing this button you can change the spin speed of the selected programme Available options Rinse hold By selecting this function the water of the last rinse is not emptied out to prevent the fabrics from creasing Before opening the door it will be necessary to empty out the water To empty out the water please read the paragraph At the end of the programme lt _ Economy Only for cottons and synthetic items lightly or normally soiled at a temperature of 40 C or higher The washing time will be prolonged and the
3. ble to start the machine 2 After pressing button 7 it will be impossi ble to change any other programme or op tion www zanussi com To enable or disable this option press simulta neously for about 6 seconds buttons 2 and 3 Daily use Load the laundry Open the door by carefully pulling the door handle out wards Place the laundry in the drum one item at a time shaking them out as much as possible Close the door Make sure that no laundry stays be tween the seal and the door There is a risk of water leakage or damage to the laundry Measure out the detergent and the fabric softener Pull out the dispenser drawer until it stops Measure out the amount of detergent re quired pour it into the main wash compart ment J or in the appropriate compartment if the selected programme option it requires see more details in Detergent dispenser drawer If required pour fabric softener into the com partment marked the amount used must not exceed the MAX mark in the drawer Close the drawer gently www zanussi com until on the display the icon FA appears or dis appears Flap for powder or liquid detergent UP The flap posi A tion if using POW EZ lt DER detergent DOWN The flap position if using LIQUID detergent during main wash Pull out the dis penser drawer until it stops The flap is down and you wish to use powder detergent Tur
4. the colour washing temperature and degree of soil ing All commonly available washing machine deter gents may be used in this appliance powder detergents for all types of fabric powder detergents for delicate fabrics 60 C max and woollens liquid detergents preferably for low tempera ture wash programmes 60 C max for all types of fabric or special for woollens only The detergent and any additives must be placed in the appropriate compartments of the dis Washing programmes Programme Maximum and Minimum Temperature Cycle De scription Maximum Spin Speed Maximum Fabrics Load Type of Laundry COTTONS 90 Cold Main wash Rinses Maximum spin speed at 1000 rpm for model ZWN7100L 1200 rpm for model ZWN7120L Max load 8 kg Reduced load 4 kg White and coloured cotton normally soiled items www zanussi com penser drawer before starting the wash pro gramme If using liquid detergents a programme without prewash must be selected Your appliance incorporates a recirculation sys tem which allows an optimal use of the concen trated detergent Follow the product manufacturer s recommen dations on quantities to use and do not ex ceed the MAX mark in the detergent dis penser drawer Quantity of detergent to be used The type and quantity of detergent will depend on the type of fabric load size degree of soiling and hardness of the water used Follow the
5. User manual Washing Machine U S F R MANUAL ZWN 7100 L ZANUSSI ZWN 7120 L Contents Safety information 2 Washing programmes ____________ 13 Safety instructions 3 Care andcleaning______________ 16 Product description ______________ 5 Whattodoif 22nn 19 Controlpanel _ _ 6 Technical data ____ 21 First use 22222222L LLL 8 Consumption values ___ 21 Personalisation _________2_______ 8 Installation ee 22 Daily use ____ 22 ________ _ 9 Environmentalconcens___________ 24 Helpful hints and tips 12 Subject to change without notice Safety information Before the installation and use of the appliance carefully read the supplied instructions The manufacturer is not responsible if an incor rect installation and use causes injuries and damages Always keep the instructions with the appliance for future reference Children and vulnerable people safety A Warning Risk of suffocation injury or permanent disability Do not let persons children included with reduced physical sen sory reduced mental functions or lack of experience and knowl edge use the appliance They must have supervision or instruction for the operation of the appliance by a person who is responsible for their safety Do not let children play with the appliance Keep all packaging away from children Keep all detergents away from children Keep children and pets away from the appliance door when it is open If the ap
6. switch the machine off Important If you turn the programme selector dial to another programme when the machine is working the red pilot light of button 7 will blink 3 times and the messageErr is displayed to indicate a wrong selection The machine will not perform the new selected programme Select the spin speed by pressing button 2 When selecting a programme the appliance proposes automatically the maximum spin speed provided for that programme See Washing programmes for the maximum al lowed spin speed Press this button repeatedly to change the spin speed if you want your laundry to be spun at a different speed The relevant pilot light illumi nates Select the available options by means of buttons 3 4 5 and 6 Depending on the programme different options can be combined These must be selected after choosing the desired programme and before starting the programme When these buttons are pressed the corresponding pilot lights illu minate When they are pressed again the pilot lights go out If an incorrect option is selected the integrated red pilot light of the button 7 flashes 3 times and the message Err is dis played For the compatibility among the washing pro grammes and the options see chapter Wash ing programmes www zanussi com Start the programme by pressing button 7 To start the selected programme press this button the corresponding green pilot light stops blinking The pilot light 9 i
7. details The door is not properly closed Ef Close the door firmly www zanussi com 19 Possible cause Solution The drain hose is squashed or kinked Feu Check the drain hose connection The drain filter is clogged FI The machine does not empty Clean the drain filter pa and or does not spin An option or a programme that ends with the water still in the tub or a that eliminates all the spinning phases has been selected Select the draining or spinning programme The laundry is not evenly distributed in the drum Redistribute the laundry Too much detergent or unsuitable detergent creates too much foam has been used Reduce the detergent quantity or use another one Check whether there are any leaks from one of the inlet hose fittings It is not always easy to see this as the water runs down the hose check to see if it is damp There is water on the floor Check the water inlet hose connection The drain or inlet hose is damaged Replace it with a new one The cap on the emergency emptying hose has not been replaced or the filter has not been properly screwed in after cleaning action Refit the cap on the emergency emptying hose or screw the filter fully in Too little detergent or unsuitable detergent has been used Increase the detergent quantity or use another one Stubborn stains have not been treated prior to washing Unsatisfactory washing re Use commercial products to treat the
8. for heavily soiled laundry The machine performs a soak at 30 C At the end of this time the ma chine will stop automatically with water left in the tub Before starting a new washing phase it is necessary to empty out the water by Draining only turn the programme selector dial to the draining programme press then the button 7 Draining and spinning turn the programme selector dial to the spinning programme reduce the spin speed by pressing the relevant button and then press button 7 Important This programme cannot be used for very deli cate fabrics as silk or wool Pour the detergent for the soak programme into the appropriate compartment At the end of the soak after having emptied out the water you can select the washing programme first turn the programme selector dial to O then to the programme and press the button 7 RINSES Rinses Maximum spin speed at 1000 rpm or model ZWN7100L 1200 rpm for model ZWN7120L Max load 8 kg With this programme it is possible to rinse and spin cotton garments which have been washed by hand The machine performs 3 rinses followed by a final long spin The spin speed can be reduced tp DRAIN Draining of water Max load 8 kg For emptying out the water of the last rinse in programmes with the option selected which ends with water left in the tub SPIN Drain and long spin Maximum spin speed at 1000 rpm for model ZWN7100L 1200 rpm for model ZWN7120L Max load 8
9. hooks and poppers Tie any belts or long tapes Remove persistent stains before washing Rub particularly soiled areas with a special de tergent or detergent paste Treat curtains with special care Remove hooks or tie them up in a bag or net Removing stains Stubborn stains may not be removed by just water and detergent It is therefore advisable to treat them prior to washing 1 do not use acetone on artificial silk 12 1 Turn the programme selector dial to 2 Select the draining or spinning programme Reduce the spin speed if needed by press ing the relevant button 4 Press button 7 At the end of the programme the door is re leased and can be opened Turn the programme selector dial to to switch the machine off Remove the laundry from the drum and carefully check that the drum is empty If you do not in tend to carry out another wash close the water tap Leave the door open to prevent the forma tion of mildew and unpleasant smells reduced By pressing any button the appliance will come out of the energy saving status Blood treat fresh stains with cold water For dried stains soak overnight in water with a spe cial detergent then rub in the soap and water Oil based paint moisten with benzine stain remover lay the garment on a soft cloth and dab the stain treat several times Dried grease stains moisten with turpentine lay the garment on a soft surface and dab the stain with the fingert
10. kg Separate spin for hand washed garments and after pro grammes with the option selected which ends with water left in the tub You can choose the spin speed by pressing the relevant button to adapt it to the fabrics to be spun www zanussi com partment UJ SPIN REDUCTION amp RINSE HOLD EASY IRON EXTRA RINSE SPIN REDUCTION 15 Programme Maximum and Minimum Temperature Cycle De Detergent Com scription Maximum Spin Speed Maximum Fabrics partment Load Type of Laundry OFF SI cancelling the programme which is running or to switch the machine off 1 Standard programmes for the Energy Label consumption values According to regulation 1061 2010 the COTTONS with ECO lt option selected and the COTTONS with ECO lt _ option selected are respectively the standard 60 C cotton programme and the standard 40 C cotton programme They are the most efficient programmes in terms of combined energy and water consumptions for washing normally soiled cotton laundry The water temperature of the washing phase may differ from the temperature declared for the selected programme 2 This option is not active at a temperature lower than 40 C 3 If you select the Super Quick option by pressing button 3 we recommend that you reduce the maximum load as indicated Full loading is possible however with somewhat reduced cleaning results 4 If using liquid detergents a programme without PREWASH
11. load manually and then select the spinning programme The machine is fitted with a type of motor which makes an unusual noise The machine makes an un compared with other traditional motors This new motor ensures a softer usual noise start and more even distribution of the laundry in the drum when spinning as well as increased stability of the machine No water is visible in the Machines based on modern technology operate very economically using drum very little water without affecting performance If you are unable to identify or solve the prob lem contact our service centre Before tele phoning make a note of the model serial num ber and purchase date of your machine the Service Centre will require this information Technical data Dimensions Width 60 cm Height 85 cm Depth 63 cm Electrical connection Information on the electrical connection is given on the rating plate on the inner edge of the appliance door Water supply pressure Minimum 0 05 MPa Maximum 0 8 MPa Maximum Load Cotton 8kg Spin Speed Maximum 1000 rpm ZWN7100L 1200 rpm ZWN7120L Consumption values The data of this table are approximate Different causes can change the data the quantity and type of laundry the water and ambient temperature www zanussi com 21 Programmes Load Energy con Water con Approxi Remaining Remaining UC sumption sumption li mate pro moisture moisture Ca tre gramme 1 1 duration Z
12. move the appli ance because it is heavy Always wear safety gloves Make sure that there is air circulation be tween the appliance and the floor Adjust the feet to have the necessary space between the appliance and the carpet Electrical connection A Warning Risk of fire and electrical shock The appliance must be earthed www zanussi com Make sure that the electrical information on the rating plate agrees with the power supply If not contact an electrician Always use a correctly installed shockproof socket Do not use multi plug adapters and extension cables Make sure not to cause damage to the mains plug and to the mains cable Contact the Service or an electrician to change a dam aged mains cable Connect the mains plug to the mains socket only at the end of the installation Make sure that there is access to the mains plug after the installation Do not pull the mains cable to disconnect the appliance Always pull the mains plug Do not touch the mains cable or the mains plug with wet hands This appliance complies with the E E C Di rectives Water connection Make sure not to cause damage to the water hoses The appliance is to be connected to the wa ter mains using the new supplied hose sets Old hose sets must not be reused Before you connect the appliance to new pipes or pipes not used for a long time let the water flow until it is clean The first time you use the appli
13. must be selected Care and cleaning Warning You must DISCONNECT the appliance from the electricity supply before you can carry out any cleaning or maintenance work Descaling The water we use normally contains lime It is a good idea to periodically use a water softening powder in the machine Do this separately from any laundry washing and according to the soft Remove the drawer To aid cleaning the ening powder manufacturer s instructions This by pressing the catch top part of the addi will help to prevent the formation of lime depos downwards and by tive compartment its pulling it out Flush it should be removed out under a tap to re External cleaning move any traces of Clean the exterior cabinet of the appliance with accumulated powder soap and water only and then dry thoroughly Cleaning the dispenser drawer Cleaning the drawer recess The washing powder and additive dispenser drawer should be cleaned regularly Having removed the drawer use a small brush to clean the re cess ensuring that all washing powder resi due is removed from the upper and lower part of the recess 16 www zanussi com Replace the drawer and run the rinse pro gramme without any clothes in the drum Cleaning the pump The pump should be inspected regularly and particularly if the appliance does not empty and or spin the appliance makes an unusual noise during draining due to objects suc
14. need to open it you have to switch the machine off by turning the selector dial to After a few mi nutes the door can be opened Pay attention to the water level and tem perature 11 After closing the door it is necessary to select the programme and options again and to press button 7 At the end of the programme The machine stops automatically Some acous tic signals sound and a blinking 7 appears on the display The pilot light of button 7 and the pilot light 9 go off If you have set a programme or an option that ends with water left in the tub the pilot light 9 remains on The door is locked to indicate that the water must be emptied out During this time the drum continues to turn at regular intervals until water draining Follow the below instructions to empty out the water Stand by once the programme has finished after a few minutes the energy saving system will be enabled The brightness of the display is Helpful hints and tips Sorting out the laundry Follow the wash code symbols on each garment label and the manufacturer s washing instruc tions Sort the laundry as follows whites col oureds synthetics delicates woollens Before loading the laundry Never wash whites and coloureds together Whites may lose their whiteness in the wash New coloured items may run in the first wash they should therefore be washed separately the first time Button up pillowcases close zip fasteners
15. product manufacturers instructions on quantities to use Use less detergent if you are washing a small load the laundry is lightly soiled large amounts of foam form during washing Degrees of water hardness Water hardness is classified in so called de grees of hardness Information on hardness of the water in your area can be obtained from the relevant water supply company or from your lo cal authority If the water hardness degree is medium or high we suggest you to add a water softener following always the manufacturer s in structions When the degree of hardness is soft readjust the quantity of the detergent Detergent Com partment SPIN REDUCTION UJ RINSE HOLD UJ ECO2 B SUPER QUICK PREWASH EASY IRON EXTRA RINSE 13 Programme Maximum and Minimum Temperature Cycle De scription Maximum Spin Speed Maximum Fabrics Load Type of Laundry Detergent Com partment GS SYNTHETICS 60 X Cold Main wash Rinses Maximum spin speed at 900 rpm Max load 3 5 kg Reduced load 1 5 kg Synthetic or mixed fabrics underwear coloured gar ments non shrink shirts blouses 37 Special programmes S DELICATES 40 X Cold Main wash Rinses Maximum spin speed at 700 rpm Max load kg 3 5 Reduced load kg 1 5 Delicate fabrics acrylics viscose polyester HANDWASH 30 X Cold Main wash Rinses Maximum spin speed at 1000 rpm for model ZWN7100L 900 rpm fo
16. WN7100L ZWN7120L minutes Cottons 60 C 8 1 4 63 160 60 53 Cottons 40 C 8 0 6 63 130 60 53 Da K 3 5 0 6 54 80 37 35 Delicates 40 C 3 0 6 63 65 37 35 Wool Hand wash 30 C 2 0 25 55 60 32 30 Standard cotton programmes o Senca Ie 8 1 17 61 205 60 53 cotton o SERE E 4 0 77 49 159 60 53 cotton o Se ROSSE 0 7 48 161 60 53 cotton 1 At the end of spin phase Off Mode W Left On Mode W 0 10 0 98 The information given in the charts above are in compliance with the EU Commission regulation 1015 2010 implementing directive 2009 1 25 EC Installation Unpacking All transit bolts and packing must be removed before using the appliance You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again After removing all the Remove the power packaging carefully supply cable and the lay machine on it s hose from the hose back to remove the holders on the rear of polystyrene base from the appliance the bottom 22 www zanussi com Unscrew the three Slide out the relevant bolts plastic spacers Fill the smaller upper hole and the two arge ones with the corresponding plastic plug caps supplied in Open the porthole remove the polystyr ene block fitted on the door seal and pull out all items from the drum the bag containing the instruction book let Positioning I
17. ance make sure that there is no leakage Use Warning Risk of injury electrical shock fire burns or damage to the appliance Use this appliance in a household environ ment Obey the safety instructions on the detergent packaging Do not put flammable products or items that are wet with flammable products in near or on the appliance Do not touch the glass of the door while a programme operates The glass can be hot Make sure that you remove all metal objects from the laundry Do not put a container to collect possible wa ter leakage under the appliance Contact the Service to ensure which accessories can be used Care and Cleaning A Warning Risk of injury or damage to the appliance Do not use water spray and steam to clean the appliance Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abrasive products abrasive cleaning pads solvents or metal objects Disposal A Warning Risk of injury or suffocation Disconnect the appliance from the mains supply Cut off the mains cable and discard it Remove the door catch to prevent children and pets to get closed in the appliance Service Contact the Service to repair the appliance We recommend only the use of original spare parts www zanussi com Product description Detergent dispenser drawer Control panel Door opening handle Rating plate Drain pump E Adjustable f
18. e pump Never remove the pump cover during a wash cycle always wait until the appliance has finished the cycle and is empty When refitting the pump cover ensure it is securely re tightened so as to stop leaks and young children being able to remove it 17 Cleaning the water inlet filters Important If the appliance doesn t fill takes long to fill with water the starting button blinks yellow or the display if available shows the relevant alarm see chapter What to do if for more details check if the water inlet filters are blocked To clean the water inlet filters Turn off the water tap Unscrew the hose from the tap Clean the filter in the hose with a stiff brush Screw the hose back onto the tap Make sure the connection is tight Unscrew the hose from the machine Keep a rag nearby because some water may flow Clean the filter in the valve with a stiff brush or with the piece of cloth 18 Screw the hose back to the machine and make sure the connection is tight Turn on the water tap Frost precaution If the machine is exposed to temperatures be low 0 C certain precautions should be taken Turn off the water tap Unscrew the inlet hose Place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out Screw the water inlet hose back on and repo sition the emergency emptyi
19. ed at a lower temperature Measure out detergent according to the wa ter hardness the degree of soiling and the quantity of laundry being washed 25 26 www zanussi com www zanussi com 27 www zanussi com shop e ee 9 6 192986482 A 512012 MN
20. eet Detergent dispenser drawer LUJ Compartment for detergent used for prewash Ald and soak phase or for stain remover used during the stain action phase if available The prewash and soak detergent is added at the beginning of the wash programme The stain remover is add ed during the stain action phase UIJ Compartment for powder or liquid detergent used for main wash If using liquid detergent pour it just before starting the programme Compartment for liquid additives fabric soft ener starch Follow the product manufacturer s recommendations on quantities to use and do not exceed the MAX mark in the detergent dispenser drawer Any fabric softener or starching additives must be poured into the compartment before starting the wash programme IA Flap for powder or liquid detergent see Flap for powder or liquid detergent in the chapter Daily use for more details www zanussi com 5 Child safety Make sure that children or pets do not climb in to the drum To prevent children and pets be coming trapped inside the drum this machine in corporates a special feature Control panel el M To activate this de vice rotate the button without pressing it inside the door clock wise until the groove is horizontal If neces sary use a coin To disable this de vice and restore the possibility of closing the door rotate the button anti clockwise until the groove is ver tical
21. h as safety pins coins etc blocking the pump a problem with water draining is detected see chapter What to do if for more de tails Warning Before opening the pump door switch the appliance off and remove the mains plug from the socket Proceed as follows Unplug the appliance If it is necessary wait until the water has cooled down Open the pump door Z Place a container close to the pump to collect any spillage Pull out the emergen cy emptying hose place it in the con tainer and remove its cap When no more water comes out unscrew the pump cover by turning it anti clockwise and remove the filter Use pliers if necessary Al ways keep a rag nearby to dry up any water spillages when removing the cover Clean the filter under a tap to remove any traces of fluff www zanussi com Remove foreign bod ies and fluff from the filler seat and from the pump impeller Check carefully whether the pump impeller ro tates it rotates jerkily If it doesn t rotate please contact your Service Centre Put the cap back on the emergency emptying hose and place the latter back in its seat Replace the filter into the pump by inserting it correctly into the special guides Screw the pump cover firmly by turning it clock wise Close the pump door Caution When the appliance is in use and depending on the programme selected there can be hot water in th
22. ips and a cotton cloth Rust oxalic acid dissolved in hot water or a rust removing product used cold Be careful with rust stains which are not recent since the cellu lose structure will already have been damaged and the fabric tends to hole Mould stains treat with bleach rinse well whites and fast coloureds only Grass soap lightly and treat with bleach whites and fast coloureds only Ball point pen and glue moisten with ace tone lay the garment on a soft cloth and dab the stain Lipstick moisten with acetone as above then treat stains with methylated spirits Treat any re sidual marks with bleach www zanussi com Red wine soak in water and detergent rinse and treat with acetic or citric acid then rinse Treat any residual marks with bleach Ink depending on the type of ink moisten the fabric first with acetone then with acetic acid treat any residual marks on white fabrics with bleach and then rinse thoroughly Tar stains first treat with stain remover methy lated spirits or benzine then rub with detergent paste Detergents and additives Good washing results also depend on the choice of detergent and use of the correct quantities to avoid waste and protect the envi ronment Although biodegradable detergents contain substances which in large quantities can upset the delicate balance of nature The choice of detergent will depend on the type of fabric delicates woollens cottons etc
23. king compartment of the detergent drawer and then run the drain programme This will activate the ECO Valve device avoiding that part of the detergent remains unused at next washing EJ problem with the water supply Eg problem with the water draining Ef door open Once the problem has been eliminated press the button 7 to restart the programme If after all checks the problem persists contact your local Service Centre Possible cause Solution The door has not been closed EYO Close the door firmly The plug is not properly inserted in the power socket Insert the plug into the power socket There is no power at the socket Please check your domestic electrical installation The main fuse has blown The machine does not start Replace the fuse The selector dial is not correctly positioned and the button 7 has not been pressed Please turn the selector dial and press the button 7 again The delay start has been selected If the laundry are to be washed immediately cancel the delay start The Child Safety Lock has been activated Deactivate the Child Safety Lock The water tap is closed E 10 Open the water tap The inlet hose is squashed or kinked EID Check the inlet hose connection The machine does not fill The filter in the inlet hose or the inlet valve filter are blocked FIO Clean the water inlet filters See Cleaning the water inlet filters for more
24. lluminates to indicate that the appliance starts operating and the door is locked If you have chosen a delayed start the machine will begin the countdown Important If an incorrect option is selected the message Err is displayed for a few seconds and the red pilot light of this button blinks 3 times Select the Delay Start by pressing button 8 Before you start the programme if you wish to delay the start press this button to select the desired delay The selected delay time value will appear on the display for a few seconds then the duration of the programme will appear again You must select this option after you have set the programme and before you start the pro gramme You can cancel or modify the delay time at any moment before you press button 7 Selecting the delay start 1 Select the programme and the required op tions 2 Select the delay start by pressing button 8 Press button 7 the machine starts its hourly countdown the programme will start after the selected delay has expired Cancelling the Delay Start after having started the programme 1 Set the washing machine to PAUSE by pressing button 7 2 Press button 8 once On the display will appear 7 3 Press button 7 again to start the pro gramme Important The selected delay can be changed only after selecting the washing programme again www zanussi com The door will be locked throughout the delay time If you
25. n be opened light on the door cannot be opened The ma chine is working or has stopped with water left in the tub light off the door can be opened The pro gramme is finished or the water has been emptied out light blinking the door is opening in a few mi nutes Display 10 The display shows the following information 10 1 Child safety lock This device permits you to leave the appliance unattended during it s functioning 10 2 Duration of the selected programme After selecting a programme the duration is displayed in hours and minutes for example 2 135 The duration is calculated automati cally on the basis of the maximum recommen ded load for each type of fabric After the programme has started the time remaining is updated every minute First use i Ensure that the electrical and water con nections comply with the installation in structions Remove the polystyrene block and any material from the drum Pour 2 litres of water into the main wash compartment Il of the detergent drawer Personalisation Acoustic signals The machine is provided with an acoustic de vice which sounds in the following cases at the end of the cycle if there is a fault By pressing the 4 and 5 buttons simultaneously for about 6 seconds the acoustic signal is de activated except if there is a fault By pressing these 2 buttons again the acoustic signal is re activated
26. n the flap up Measure out the detergent Pour the powder detergent into the main wash com partment UV i Remove the remaining powder form the flap There is remaining powder detergent in the main wash compartment at the end of a washing programme Check if the flap is in the right position The flap is up and you wish to use liquid detergent Turn the flap down Measure out the detergent For the quantity of detergent re fer always to what is written on the product packing and ensure that the detergent can be poured in the drawer Pour the liquid detergent in the compart ment IIJ without exceeding the limit indica ted in the flap Close the dispenser drawer A Warning Do not use the flap in DOWN position with Gelatinous detergent or thick detergent Powder detergent With programmes with prewash 10 Do not use liquid detergent if the washing programme doesn t start immediately In these cases use the flap in UP position Select the required programme by means of the programme selector dial 1 Turn the programme selector dial to the re quired programme The green pilot light of button 7 starts to flash The selector dial can be turned either clockwise or anticlockwise Turn the selector dial to position to reset the programme to switch the machine OFF At the end of the programme the selector dial must be turned to position O to
27. need to open the door you must first set the washing machine to PAUSE by pressing button 7 and wait a few minutes be fore opening the door After you have closed the door press the same button again Important The Delay Start cannot be selected with the draining programme Altering an option or a running programme It is possible to change some options before the programme carries them out Before you make any change you must pause the washing machine by pressing button 7 Changing a running programme is possible only by resetting it Turn the programme selector dial to and then to the new programme position Start the new programme by pressing button 7 again The washing water in the tub will be not emp tied out Interrupting a programme Press the button 7 to interrupt a programme which is running the corresponding pilot light starts blinking Press the button again to restart the programme Cancelling a programme Turn the selector dial to to cancel a pro gramme which is running Now you can select a new programme Opening the door after the programme has started First set the machine to pause by pressing the button 7 If the pilot light 9 blinks and after a few minutes goes off the door can be opened If the pilot light 9 remains lit this means that the machine is already heating or that the water lev el is too high In any case do not try to force the door open If you cannot open the door but you
28. ng hose after having put the cap on again When you intend to start the machine up again make sure that the room temperature is above 0 C Emergency emptying out If the water is not discharged proceed as fol lows to empty out the machine pull out the plug from the power socket close the water tap if necessary wait until the water has cooled down open the pump door place a bowl on the floor and place the end of the emergency emptying hose into the bowl Remove its cap The water should drain by gravity into the bowl When the bow is full put the cap back on the hose Empty the bowl Repeat the procedure until water stops flowing out clean the pump if necessary as previously de scribed replace the emergency emptying hose in its seat after having plugged it screw the pump cover again and close the door www zanussi com Important Every time you drain the water through the emergency emptying hose you must pour 2 litres of water into the main wash What to do if Certain problems are due to lack of simple maintenance or oversights which can be solved easily without calling out an engineer Before contacting your local Service Centre please carry out the checks listed below During machine operation it is possible that the red pilot light of button 7 blinks one of the fol lowing alarm codes appears on the display and some acoustic signals sound every 20 seconds to indicate that the machine is not wor
29. nk drain pipe branch This branch must be above the trap so that the bend is at least 60 cm above the ground Directly into a drain pipe at a height of not less than 60 cm and not more than 90 cm The end of the drain hose must always be ventilated i e the inside diameter of the drain pipe must be larger than the outside di ameter of the drain hose The drain hose must not be kinked potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product www zanussi com Packaging materials O The materials marked with the symbol are re cyclable gt PE lt polyethylene gt PS lt polystyrene gt PP lt polypropylene This means that they can be recycled by dis posing of them properly in appropriate collec tion containers Ecological hints To save water energy and to help protect the environment we recommend that you follow these tips www zanussi com Normally soiled laundry may be washed with out prewashing in order to save detergent water and time the environment is protected too The machine works more economically if it is fully loaded With adequate pre treatment stains and limi ted soiling can be removed the laundry can then be wash
30. nstall the machine on a flat hard floor Make sure that air circulation around the machine is not impeded by carpets rugs etc Check that the machine does not touch the wall or other kitchen units Level the washing machine by raising or lowering the feet The feet may be tight to adjust as they incorporate a self locking nut but the machine MUST be level and stable Any necessary adjustment can be made with a spanner Accurate levelling prevents vibration noise and displacement of the machine during operation Never place cardboard wood or similar materi als under the machine to compensate for any unevenness in the floor www zanussi com If necessary check the setting with a spi rit level Rubber feet kit 4055126249 Available from your authorized dealer The rubber feet are particularly recommended on floating slippery and wooden floors Mount the rubber feet to prevent vibration noises and displacement of the appliance dur ing operation Read carefully the instructions supplied with the kit Water inlet Warning This appliance must be connected to a cold water supply Caution Before connecting up the appliance to new pipework or to pipework that has not been used for some time run off a reasonable amount of water to flush out any debris that may have collected Caution Do not use the hose from your previous appliance to connect to water supply Connect the hose to a tap with a 3 4 thread Alwa
31. pliance has a child safety device we recommend you acti vate It General Safety Before maintenance deactivate the appliance and disconnect the mains plug from the mains socket Do not change the specification of this appliance 2 www zanussi com Obey the maximum load volume of 8 kg refer to the Programme chart chapter If the supply cord is damaged it must be replaced by the manu facturer its service agent or similarly qualified persons in order to avoid a hazard The operating water pressure minimum and maximum must be between 0 5 bar 0 05 MPa and 8 bar 0 8 MPa The ventilation openings in the base if applicable must not be ob structed by a carpet The appliance is to be connected to the water mains using the new supplied hose sets Old hose sets must not be reused A Safety instructions Installation Remove all the packaging and the transit bolts Keep the transit bolts When you move the appliance again you must block the drum Do not install or use a damaged appliance Do not install or use the appliance where the temperature is less than 0 C or where it is exposed to the weather Obey the installation instruction supplied with the appliance Make sure that the floor where you install the appliance is flat stable heat resistant and clean Do not install the appliance where the appli ance door can not be fully opened Always be careful when you
32. r model ZWN7120L Max load 2 kg Special programme for delicate fabrics with hand wash ing care symbol WOOL 40 Main wash Rinses Maximum spin speed at 1000 rpm for model ZWN7100L 900 rpm for model ZWN7120L Max load 2 kg Washing programme for machine washable wool as well as for hand washable woollens and delicate fabrics Note A single or bulky item may cause imbalance If the appliance doesn t perform the final spin phase add more items redis tribute the load manually and then select the spinning pro gramme JEANS 40 Main wash Rinses Maximum spin speed at 1000 rpm for model ZWN7100L 1200 rpm for model ZWN7120L Max load 4 kg With this programme it is possible to wash items like pants shirts or jackets in denim and also jersey realized with hi tech materials The Extra Rinse option will be activated au tomatically 14 SPIN REDUCTION RINSE HOLD ECO2 SUPER QUICK PREWASH EASY IRON EXTRA RINSE SPIN REDUCTION RINSE HOLD SUPER QUICK PREWASH EXTRA RINSE SPIN REDUCTION RINSE HOLD SPIN REDUCTION RINSE HOLD SPIN REDUCTION RINSE HOLD PREWASH EASY IRON Uja uy BE B BE EE www zanussi com Programme Maximum and Minimum Temperature Cycle De scription Maximum Spin Speed Maximum Fabrics Load Type of Laundry Detergent Com iJ soak 30 Prewash Soak for about 40 minutes Stop with water in the tub Max load 8 kg Special programme
33. stubborn stains sults The correct temperature was not selected Check if you have selected the correct temperature Excessive laundry load Reduce the laundry load The programme is still running Wait the end of washing cycle 3 The door lock has not been released The door will not open ERA Wait until the pilot light 9 goes off There is water in the drum Select drain or spin programme to empty out the water The transit bolts and packing have not been removed Check the correct installation of the appliance The support feet have not been adjusted Check the correct levelling of the appliance The machine ibi ates noisy The laundry is not evenly distributed in the drum Redistribute the laundry Maybe there is very little laundry in the drum Load more laundry 20 www zanussi com Possible cause Solution The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum The laundry is redistributed by re verse rotation of the drum This may happen several times before the un balance disappears and normal spinning can resume If after 10 minutes the laundry is still not evenly distributed in the drum the machine will not Spinning starts late or the spin In this case redistribute the load manually and select the spin pro machine does not spin gramme Redistribute the laundry The load is too small Add more items redistribute the
34. washing temperature will be reduced You can use this option if you want to wash normally soiled laundry and at the same time save ener gy Super Quick Short cycle for lightly soiled items or for laundry which needs only freshening up We recom mend you to reduce the fabrics loading Prewash By selecting this option the machine performs a prewash cycle before the main wash phase The washing time will be prolonged This option is recommended for heavily soiled laundry Easy Iron By selecting this option the laundry is gently washed and spun to avoid any creasing In this www zanussi com way ironing is easier Furthermore the machine will perform some additional rinses in some pro grammes On cotton programmes the maximum spin speed is reduced automatically Extra Rinse This appliance is designed to save energy If it necessary to rinse the laundry using an extra quantity of water extra rinse select this option Some additional rinses will be performed This option is recommended for people who are al lergic to detergents and in areas where the wa ter is very soft Start Pause This button allows you to start or to interrupt the selected programme Delay Start The programme can be delayed from 30 min 60 min 90 min 2 hours and then by 1 hour up to a maximum of 20 hours by means of this but ton Door locked pilot light The pilot light 9 illuminates when the pro gramme starts and indicates if the door ca
35. ys use the hose supplied with the appliance 23 The other end of the inlet hose which con nects to the appliance can be turned as showed in the picture Do not place the inlet hose downwards Angle the hose to the left or right depending on the position of your water tap Set the hose correctly by loosening the ring nut After posi tioning the inlet hose be sure to tighten the ring nut again to prevent leaks Caution The inlet hose must not be lengthened If it is too short and you do not wish to move the tap you will have to purchase a new longer hose specially designed for this type of use Water drainage The end of the drain hose can be positioned in three ways Hooked over the edge of a sink us ing the plastic hose guide Environmental concerns A The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent 24 In this case make sure the end cannot come unhooked when the machine is emptying This could be done by tying it to the tap with a piece of string or attaching it to the wall I jj a J 5 Z In a si
Download Pdf Manuals
Related Search