User`s Manual - Sans Digital
Contents
1. Spare Create Vol RAID Set pean Yes a Press key X Button No ii Quick Volume and SCSI Cable poe E RAID Set Setup Password Foreground Faster Completion Note 1 Background Instant Available pupuk PEREEE LEER Note It will cause hard disk push towards the backplane and the tray handle is unable to rotate once the screws do not properly fixed IR35S1 did not set any default RAID level hence please set your desire RAID level after booth the device Please be noted when you set the RAID level plese make sure all hard disk inside the device is Green light PCI Bracket RS232 cable SCSI Card amp2. Front Cover Page 4 Page 5 Product Family Produkt Familie Famile de produit Familia de productos Version 1 0 Famigilia di prodotti a 77 U ERRI an INSTA RA ID a 2 5 Hard disk Enclosure with 10 in 1 Card Input 0000 and press ENTER for 12 times in order to next process Reader Writer Blue backlight LCD Panel with Status and Battery Indicator Three memory card slots supports CF III MD SM MS MS PRO SD Mini SD MMC Card XD etc USB 2 0 host interface backward compatible with USB 1 1 Built in Rechargeable Lithium lon Battery Single button backup from memory card to hard drive Durable and light weight Aluminum Case with Carry bag Pass word 0000 The number of physical drives in a specific RAID set determines the RAID levels that can be implemented with the RAID set RAID 0 requires 1 or more physical drives per RAID set RAID 1 requires at least 2 physical drives per RAID set RAID 1 Spare requires at least 3 physical drives per RAID set RAID 3 requires at least 3 physical drives per RAID set RAID 5 requires at least 3 physical drives per RAID set RAID 3 Spare requires at least 4 physical drives per RAID set RAID 5 Spare requires at least 4 physical drives per RAID set Stripe size default is 64k it could adjust to 4k or 128k mode under stripe size actually 128K size will get much better performance Please refer to the CD enclosed for detail user s manual Triple Int
3. Q compatible terminal or a PC running appropriate terminal emulation software The firmware based terminal array management interface can access the array through this RS 232 port Note You may allow connecting a terminal while the RAID subsystem is at power on state Fan Removable Tray Module 5 LA 1 N amp N S N KA x CE ocra ofo wo FO BOB o i To ensure proper communications between the RAID subsystem and the VT 100 Terminal Emulation User s Guide amp CD Title 1 jj i i ji Pek o f Wipcrses Please configure the VT 100 terminal emulation settings to the values shown below RS232 cable 1 PCI Bracket oWo W MEM sosi Pon epel RS232 cable PCI Bracket RS232 Cable 1 Host Connection Databits 8 IR35S1 Rear Panel Installing HDD in the Removable Tray Module PC Power Supply a Available Capacity xxx GB 2 PCI bracket a Power On Total X Disks Selected Capacity xxx GB RS232 Cable RAID 0 1 Demount the transport holder scsi card 5 RAID 1 l 2 Mount the HDD into the tra kaei y RS232Card i RAID 1 Spare RAID 0 1 Spare Select Stripe Size eG G oer lt gt RAID 3 SSS sees sel Connect to RAID 3 Spare ole oe gaen rs Terminal RAID 5 Motherboard r l RAID 5
4. erface RAID Subsystem Hardware RAID Engine supports RAID 0 and JBOD Triple Host Interface USB 2 0 FireWire 400 Firewire 800 Drive Interface 2x 3 5 SATA Harddrive Fan and Temperature failure detectors with purple warning LED USB 2 0 amp SATA Combo RAID Subsystem Hardware RAID Design supports RAID 0 1 Host Interface eSATA port amp USB 2 0 Drive Interface 2 x 3 5 SATA Hard Disk Hot Swappable Removable Tray Data Auto Rebuilding Hard Disk Fan and Temperature failure detectors No Driver Required SCSI to SATA RAID 5 Subsystem Hardware RAID Design supports RAID 0 1 3 5 0 1 JBOD amp Hot Spare Disk Host Interface SCSI Ultra 320 Drive Interface 5 x 3 5 SATA Hot Swappable Removable Tray Hard Disk Data Auto Rebuilding Hard Disk Fan and Temperature failure detectors to ensure system stability fencscee www sansdigital c om Page 1 Page 2 Page 3 IR35S1 system includes the following Hardware Installation Quick Volume RAID Setup Please contact our distributors in case of any missing or damaged items Front Panel Rear Panel The serial port on the controller s back plane can be used in VT 100 mode The RAID subsystem comes Item Quantity with 10 pin RS 232 serial port which using a null modem cable can be connected to any COM port on a a d K P P z host computer for VT 100 terminal management purposes It can also transfer to external for a VT 100 IR35S1 1 KA cn in S i
Download Pdf Manuals
Related Search