Driver`s Ed Guide - Castle Creations
Contents
1. This warranty does not cover damages caused to your motor or controller from abuse Abuse includes but is not limited to the Following incorrect wiring over voltage overloading improper gearing improper motor selection incorrect controller settings insufficient batteries or connectors If you have any questions comments or wish to return your Castle ESC For warranty or non Warranty repair or replacement please contact Castle Creations Inc ESC PROGRAMMING GUIDE 1 Brake Reverse Type Option 1 With Reverse D Option 2 Without Reverse Option 3 Crawler Reverse 2 Brake Amount Option 1 25 Option 2 50 D Option 3 75 Option 4 100 3 Reverse Amount Option 1 25 Option 2 50 D Option 3 75 Option 4 100 4 Punch Control Option 1 High Option 2 Medium Option 3 Low Option 4 Lowest Option 5 Disabled D 5 Drag Brake Option 1 Disabled D Option 2 10 Option 3 20 Option 4 30 Option 5 40 6 Throttle Dead Band Setting 1 Large 0 1500 ms Setting 2 Normal 0 1000 ms D Setting 3 Small 0 0750 ms Setting 4 Very Small 0 0500 ms Setting 5 Smallest 0 0250 ms 7 Voltage Cutoff Option 1 None Option 2 Auto Lipo D Option 3 5v Option 4 6v Option 5 9v Option 6 12v 8 Motor Timing Option 1 Lowest Option 2 Normal D Option 3 Highest 9 Motor Type Option 1 Brushless D Option 2 Brushed Reversing Option 3 Brushed High Power Note D De2. be using with the Castle ESC The ESC may be damaged if this setting does not match the motor type hook up method in the car and this damage is not covered under warranty Option 1 Brushless Default See Brushless Motor Setup diagram on page 9 Uses all three of the ESC motor wires or motor connectors connected to all three of the brushless motor wires If the motor spins the wrong way with forward throttle swap any two of the wires to get the correct direction Applies to sensorless brushless only Reverse motor direction using Castle Link with sensored brushless motors Option 2 Brushed Reversing See Reversing Brushed Motor Setup diagram on page 11 Uses the Red and Black ESC motor wires or outside motor connectors on the ESC to connect to the and side of the brushed motor If the motor spins in the wrong direction with Forward throttle reverse the motor wires For correct motor direction Option 3 Brushed High Power See Figure 3 High Power Brushed Motor Setup on page 12 Connect all three of the ESC motor wires or motor connectors on the ESC to the negative side of the motor You can either use a Y harness from the ESC battery input positive wire to connect to both the battery and the positive side of the motor or use a single wire From the positive ESC input to the positive battery pole and then continue to the positive side of the motor TROUBLESHOOTING IF you re still having difficulties with your C
3. 0 Power Default Allows only 50 of available braking power at Full brake Option 3 75 Power Allows 75 of available braking power at full brake Option 4 100 Power Allows all available braking power at full brake 3 Reverse Amount Sets how much power will be applied in the reverse direction if reverse is enabled Option 1 25 Power Allows only 25 power in reverse Option 2 50 Power Default Allows only 50 power in reverse Option 3 75 Power Allows only 75 power in reverse Option 4 100 Power Allows 100 power in reverse 4 Punch Traction Control This setting controls how fast the throttle position within the ESC can be changed over time This smooths high power starts and limits punch somewhat As explained previously acceleration is a matter of battery capability but you may not want 100 of what the battery can deliver in every situation This setting is crucial to drag racing as it can be used as a traction control to match traction conditions The lower the setting the less throttle change limiting there is For pure burnout and wheelie action use a very low setting or the disabled setting For softer acceleration or for a low grip surface raise it up to a higher setting Don t be afraid to use these settings It may be Fun to watch your car do back flips but sooner or later you are going to want to be able to drive it under some semblance of control This is THE setting to put you back into contr
4. DRIVER S ED GUIDE INSTRUCTION MANUAL FOR ALL CASTLE CREATIONS SURFACE BRUSHLESS POWER SYSTEMS WARNING This is an extremely powerful brushless motor system We strongly recommend removing your pinion gear for your own safety and the safety of those around you before performing calibration and programming functions with this system Please keep your hands hair pets Fuzzy purple shorts and garden gnomes clear from the gear train and wheels of an armed high performance system Rubber tires will grow to extreme size on a high speed vehicle DO NOT hold the vehicle in the air and run it up to Full throttle Tire Failures at speed can cause serious injury Make sure your tires are securely glued to the rims and check them often Always disconnect the battery From the ESC when you are finished using your vehicle The switch on the ESC controls the power that is delivered to the receiver and servo s The controller will always draw current when it is connected to the battery and will completely discharge batteries if they are connected for long durations This may cause failure of your batteries and or ESC Castle Creations will not warranty ESCs damaged by batteries that are left plugged in Castle Creations is not responsible for any damage as a result of batteries left plugged in to your ESC ALWAYS disconnect your batteries after use Your Castle ESC is programmed to sound a tone every thirty seconds to remind you that it is still powered QUIC
5. K START GUIDE Solder a high quality battery connector to the ESC 2 Mount the ESC and motor into the vehicle 3 Plug in the 3 motor wires to the 3 motor wires on the ESC or into the gold bullet connectors on your ESC 4 Plug in the ESC Rx lead to the throttle channel 2 on your receiver 5 Make sure the ESC s switch is off NOTE if no switch is present skip to step 7 6 7 b bP Plug in a battery Holding Full throttle on your transmitter turn the switch ON NOTE if your ESC does not have a switch hold full throttle on your transmitter efore plugging in the battery A After a few seconds you ll hear multiple tones and the red LED will come on with a single continuous beep B Now hold full brake and after a Few seconds you ll hear multiple tones and the yellow LED will come on with a single continuous beep C Now relax to neutral and after a few seconds you ll hear multiple tones and ALL the LEDs will light up D A few seconds later the ESC will arm with a double tone and yellow LED You re ready to go EASY TO USE SOPHISTICATED ENOUGH TO WIN EVERYTHING Castle controllers are extremely simple to set up and optimize for your application Most users may simply plug the controller into their motor radio and battery and run it immediately Advanced users may wish to access the incredible tuning Features using their Windows based PC and the Castle Link interface With Castle Link software you can tune the ESC exactly
6. NOT CUT any part of the wire length from any other motor regardless of brand or type Sei In most cases only the last 1 4 inch or so of most motor wires are able to ncn be soldered If they are clipped shorter you may not be able to solder the remaining portion of the wire and the motor will not run properly if at all IF CASTES ett the motor is supplied with connectors you do not want to use simply neme chand on ort unsolder the original motor connectors from the wires do not cut di them off Use a high quality connector only not included m Connect controller and motor using supplied connectors Receiver There is no polarity on the three ESC to motor wires so do not worry about how you connect them initially You may find it necessary to swap two wires if the motor runs in reverse This will be explained below Note IF running a sensored brushless motor with a sensored ESC DO NOT change the wire orientation Change the motor direction setting with Castle Link REVERSING Brushed Motor Wiring BRUSHED MOTOR MEESE Reversing Brushed Motor Mode WIRING DIAGRAM ior Use this mode if you wish to use reverse Make sure you change the Motor type setting to Brushed Reversing in the ESC before using a brushed motor Use only the red and black motor wires from the ESC or the outside connectors on the ESC In most applications the red wire From the ESC will connect to the red wire or positive side h
7. are calibrated and armed do one last check before going out and experiencing the Castle brushless difference Slowly advance the throttle and check the rotation direction of the motor and the color of the LEDs on the ESC IF the motor is spinning in the right direction and the GREEN LED is blinking green then you are ready for a test run before going into the settings of the ESC IF the ESC shows the green LED with throttle but the wheels spin in the wrong direction you ll need to switch any two of the motor wires example switch from red to red and black to black to red to black and black to red Castle Link capable Castle products may be connected to your PC using the Castle Link USB adapter The Castle Link software will give you access to a whole new world of tuning options You may use Castle Link to tune your throttle curve and brake curve set your drag brake Feel and use the incredible Torque Limit to keep the front end of your car on the ground with all the power you have at your command As new features become available you can install them in your Castle ESC for real time updates All of this ensures your Castle ESC will be the best that it can be To use Castle Link Disconnect the ESC from the throttle channel on the receiver and connect the ESC to the Castle Link adapter chip via the ESC s receiver wire Castle ESCs may also be manually programmed using your transmitter and receiver Manual programming may not provide access to a
8. astle ESC after trying the suggestions offered here please contact Castle Creations technical support at the e mail or phone number in the next section Problem My Castle ESC may or may not arm but it will not calibrate to my transmitter Solution Most calibration issues can be solved by changing settings on the transmitter Make sure you have both your throttle and brake endpoints called EPA or ATV on your radio on the throttle channel out to between 100 to 120 Make sure if you have a Futaba or Futaba made transmitter to have the throttle channel set to the reversed position Problem My ESC calibrates For the full throttle and full brake positions but won t calibrate to the neutral throttle position yellow LED keeps flashing with single beeps Solution Try moving the throttle trim one way then the other usually towards the throttle side is best IF your transmitter has a 50 50 and 70 30 setting For the throttle set it for 50 50 and retry calibration Also if you have changed the dead band to a narrower band you may want to try going back to the normal setting IF you have a Mamba Max Pro and the ESC is not beeping the yellow flashing light at neutral is normal and the ESC is ready for use Problem My vehicle acts like it has turbo lag poor acceleration punch for the first few feet or yards and then it kicks in Solution Make sure you re using high quality batteries and a battery connector capable of high amp fl
9. he ESC switch on 4 The ESC will go through its boot up sequence blinking green 5 There will be a sequence of melodic tones and the light will turn red 6 Keep holding the trigger within 6 8 seconds the light will turn yellow You are in programming mode let the trigger return to neutral When in programming mode the ESC will beep once pause then beep once again and repeat until a change is made with your transmitter IF you accept setting 1 Brake Reverse Type s default option 1 Reverse Lockout you would pull Full throttle to accept option one When the trigger is returned to neutral the beep pattern will change to 2 beeps followed by 1 beep meaning that by selecting option 1 you jump to setting 2 IF at setting 2 Brake Amount you reject option 1 25 by going to Full brake reverse the beep pattern will change to 2 beeps meaning it s still at setting 2 followed by 2 beeps meaning you are now at option 2 under setting 2 Look at the inside back cover of this guide to the Castle Car ESC Programming Guide This shows the programming sequence as settings and options Accept or reject options usually selecting the default unless you want to change that specific setting As an example say you want to turn off the default Voltage Cutoff to run NiMh batteries Work through the settings and options selecting the default options until you get to 7 beeps meaning Cutoff Voltage followed by 1 beep for option 1 None This is the correct setting f
10. in the ESC and now it s looking For the Full brake endpoint red LED blinking STEP 5 Move the throttle trigger to the full brake position and hold Full brake After a few seconds the ESC will flash the red LED and ring 4 times rapidly accepting Full brake endpoint STEP 6 After accepting the Full brake endpoint the ESC will then blink the yellow LED Now relax the trigger to the neutral position The ESC will now ring 4 times and flash the yellow LED rapidly to accept the neutral position After accepting the neutral position the ESC will ring twice flash ALL the LEDs and the yellow LED will illuminate solid yellow for all ESCs except Mamba Max Pro which flashes This is the arming tone and LED indication that the ESC IS NOW ARMED and the car will respond to throttle inputs from your transmitter From this point on when you connect batteries and turn the switch on the ESC will give the initialization tone and flash after a battery is plugged in and the switch is turned on and the arming tone will ring a second or two later IF the ESC is programmed for the Auto LiPo setting it will beep the number of cells in your LiPo pack between the initialization tones and the arming tones After the arming tone plays the ESC is ACTIVE and will respond to throttle application IF you have problems calibrating your transmitter with the Castle ESC please see the troubleshooting guide on page 37 For more tips or visit our website s FAQ pages Once you
11. ll of the Castle ESC s Features Manual Programming Follow these steps to change settings on your Castle ESC without a computer Programming With Your Transmitter You can use your transmitter to change a few of the program settings with your transmitter without a Castle Link or a Field Programming Card For basic use these settings are usually enough to get you going Transmitter programming is very easy simply answering YES or NO toa list of options These are grouped into 9 settings and each setting has several possible options You can only accept one option per setting By answering YES to an option you will jump to the next setting IF you answer NO to an option you will jump to the next option under that setting At each option you can accept it by going to Full throttle on your transmitter or you can reject the option by going to Full brake In programming terms full throttle is YES Full brake is NO The ESC will indicate that it has accepted your selection by producing a continuous skipping tone When you get this tone allow the trigger to go back to the neutral position to change to the next setting or option depending on your selection To get into programming mode on the ESC 1 Turn your transmitter on 2 Plug the battery into the ESC with its switch off Note if your ESC does not have a switch hold full throttle on your transmitter before plugging in the battery 3 Hold full throttle on your transmitter and turn t
12. notes default setting HG castlecreations com Copyright 2014 Castle Creations Inc P N 095 0012 01 Revision Date 09 2014
13. ol Option 1 High Very limited acceleration Good For 2WD vehicles on hard dirt or for general bashing when you want to be gentle on the transmission Option 2 Medium Medium acceleration limiting Good for 2WD vehicles on soft dirt and 4WD vehicles on hard dirt Option 3 Low Light acceleration limiting Good for 4WD vehicles on soft dirt Option 4 Lowest Very light acceleration limiting Good For most situations including 4WD vehicles on dirt and asphalt and 2WD vehicles on asphalt Option 5 Disabled Default Acceleration is only limited by battery ability This setting is good for 4WD sedans on carpet high traction drag racing or bashing where unlimited wheelie power is desired 5 Drag Brake Sets the amount of drag brake applied at neutral throttle to simulate the slight braking effect of a neutral brushed motor while coasting Option 1 Drag Brake OFF Default Vehicle will coast with almost no resistance From the motor at neutral throttle Option 2 Drag Brake 10 Low amount of braking effect From the motor at neutral throttle Option 3 Drag Brake 20 More braking effect From the motor at neutral throttle Option 4 Drag Brake 30 Fairly high braking effect From the motor at neutral throttle Option 5 Drag Brake 40 High braking effect from the motor at neutral throttle You may adjust the neutral throttle width of the controller with this setting Smaller values make the controller enter Forward or b
14. ood on your motor and the black wire to the black wire or negative side hood of the motor The white motor wire or center connector on the ESC is not used After calibration explained later you may need to swap the two motor wires to get the wheels to spin in the right direction Red ESC motor wire to Motor Black ESC motor wire to Motor Use a high quality connector only not included White motor wire not used Steering Servo in CH1 Connect Castle ESC to throttle in CH2 channel On Off In Switch High Power HIGH POWER Brushed Motor Mode BRUSHED MOTOR f Using High Power Brushed Motor Mode will allow for the use of lower turn WIRING DIAGRAM count brushed motors and forward only operation Make sure you change the Motor type setting to Brushed High Power in the ESC before using a brushed motor Connect all three of the ESC motor wires to the negative side of the motor You can either use a Y harness from the ESC battery input positive wire to connect to both the battery and the positive side of the motor or use a single wire From the positive ESC input to the positive battery pole and then continue to the positive side of the motor Battery Motor Use a high quality connector onli not included Steering Servo in CH1 to Motor RADIO CONNECTION Castle ESC Connect to astle throttle Your Castle ESC plugs into the
15. or NiMh Select option 1 by going to Full throttle Once you have changed the setting you want you can unplug power from the ESC to get out of programming mode You do not need to finish all of the settings The ESC will store your changes until you change them again The ESC cannot change settings itself it only does what it is told The next section of the manual gives a description of each of the settings and options and what you can expect when you change an option From default Before you make changes it is a good idea to go over the Castle Car ESC Programming Reference marking the options you wish to change 1 Brake Reverse Type Sets whether reverse is enabled or not and exactly how it can be accessed Option 1 With Reverse Default This setting allows the use of reverse only after the ESC senses two seconds of neutral throttle Use it For race practice sessions and bashing but check with your race director to see if this setting is allowed for actual racing Option 2 Without Reverse Use this setting For actual sanctioned racing events Reverse cannot be accessed under any circumstances with this setting Option 3 Crawler Reverse Reverse or Forward is accessible at any time after the ESC brakes to zero motor RPM even if the vehicle is moving 2 Brake Amount Sets what percentage of available braking power is applied with Full brake Option 1 25 Power Allows only 25 of available braking power at Full brake Option 2 5
16. ow 40 100 amps This behavior is very typical of a battery pack that is having difficulty providing the power your vehicle system requires For top performance Refer to page 7 For recommended battery capacity and C ratings for use with Castle Creations systems For NiCad NiMH packs use copper bars to connect cells rather than welded tabs Problem My battery pack is plugged into the ESC and nothing is working no steering and no throttle Solution Make sure the ESC S receiver plug is plugged into channel 2 on the receiver and that it s plugged in with the correct orientation Double check your solder connections on the battery plug and make sure the battery is showing good voltage The switch on the ESC may be bad Cut the switch off leave the wires attached to the ESC strip back some insulation and twist the bare wires together IF the ESC powers up you can attach a different switch or it is recommend to solder the wires together and cover the connection with heat shrink Doing this will not void your warranty For more troubleshooting tips visit www castlecreations com FAQ TECHNICAL SUPPORT You may contact our world class technical support department via e mail or on the phone From 9am to 5pm Central time Monday through Friday E mail support castlecreations com Phone 913 390 6939 option 1 WARRANTY INFO Your Castle ESC is warranted for one 1 year From date of purchase to be free from manufacturing and component defects
17. power that these connectors can safely handle Invest in connector sets made for high powered electric systems such as our CC Bullets Castle Connectors Traxxas TRX connectors or Deans Ultra plugs POWER Wiring Your Castle ESC has motor connectors on the motor wires or directly on the board and the battery input wires are bare You must add the connector of your choice to the battery leads We recommend a connector rated For 40 100amps such as CC Bullets Castle Connectors Deans Ultra or Traxxas TRX connectors Proper polarity is essential here Make absolutely sure positive connects to positive and negative connects to negative when you plug in your battery If reverse polarity is applied to your ESC from the battery it WILL damage your ESC This WILL NOT be covered under warranty CONNECTIONS Brushless Motor Wiring For brushless motor connection the three wires From the ESC to the motor BRUSHLESS MOTOR have no polarity Connect the red white and black motor wires to the three WIRING DIAGRAM Bae wires coming from the motor or directly to the ESC in any order If you are using a motor other than a Castle Creations motor you may need to either solder on matching male bullet plugs to your motor or solder the ESC wires directly to the motor wires IF you choose to direct solder or to shorten the motor wires you may do so on the Castle Creations NC14XX series NC15XX series NC1717 and NC2028 motors only DO
18. rake reverse with a smaller movement of your throttle trigger for finer control Be careful some transmitters offer better resolution than others IF your ESC will not respond to Neutral throttle make this setting larger Option 1 Large 0 1500 ms Option 2 Normal 0 1000 ms Default Option 3 Small 0 0750 ms Option 4 Very Small 0 0500 ms Option 5 Smallest 0 0250 ms 7 Cutoff Voltage Sets the voltage at which the ESC lowers or removes power to the motor in order to either keep the battery at a safe minimum voltage Lithium Polymer cells or the radio system working reliably NiCad NiMH cells Option 1 None Does not cut off or limit the motor due to low voltage Do not use with any Lithium packs Applications Any racing or bashing situation with 6 8 cell NiCad or NiMH packs Use this setting ONLY with NiCad or NiMH packs With continued driving the radio system may eventually cease to deliver pulses to the servo and ESC and the vehicle will not be under control You will irreversibly damage Lithium Polymer packs with this setting Option 2 Auto Lipo Default This setting automatically detects the number of LiPo cells you have plugged in It will automatically set the cut off to 3 2 volts per cell It will beep the number of cells in your LiPo pack between the initialization tones and the arming tones on initial power up of the controller Option 3 5v Cuts off limits the motor speed acceleration when the pack ge
19. smitter s throttle channel direction to the REVERSE Rev position This is either an external micro switch on the transmitter or an option available within the computer programming of the transmitter Please start by zeroing out any throttle trim that you may have set in your transmitter Don t plug in the battery yet Make sure that the battery polarity and input polarity on the ESC are correct Check the on off switch of the Castle ESC to make sure that it is in the OFF position We recommend removing your pinion gear before calibration as a safety precaution How to Calibrate the ESC Step 1 Start with the transmitter ON the battery disconnected and the ESC S switch in the OFF position if ESC has a switch Step 2 Plug a battery into your Castle ESC NOTE IF your ESC does not have a switch hold Full throttle on your transmitter before plugging in the battery Step 3 Hold Full throttle on the transmitter and turn the ESC s switch ON Keep holding Full throttle on the transmitter IF all your connections are correct you will hear one multi toned initialization ring from the motor all tones are played by the ESC vibrating the motor STEP 4 After a second or two the green LED on the ESC will blink rapidly and the motor will ring 4 times rapidly in a row accepting the full throttle endpoint After the green LED flashes and tones the ESC will blink the red LED At this point the full throttle endpoint has been set with
20. throttle channel of your receiver This is INGE lt ehannel z onoff usually channel 2 Your Castle ESC provides 5 8 volts to the receiver to iii power the receiver and the steering servo No separate receiver battery is needed to power the radio system Some servos can draw more current than the onboard BEC can handle and will require an external BEC or receiver pack Castle ESC receiver plugs are made to be used with any current receiver but you will need to make sure the polarity is correct when plugging into the receiver The signal wire is orange the positive wire is red and the negative is brown Some radio systems use white for signal red for positive and black for negative color scheme Check your receiver documentation for correct connection polarity if it s not marked Note most receivers use negative to the outside of the case and signal towards the inside of the case ESC SETUP ESC Radio Calibration Individual transmitter s signals for neutral Full throttle and full brake vary You must calibrate your Castle ESC so that it will operate effectively with your transmitter Anytime the ESC is powered up with a new transmitter or with different throttle channel settings it will need to be calibrated to know what the transmitter s throttle settings are It will also need to be calibrated after updating with new software via Castle Link IF you are using a Futaba or Futaba OEM brand transmitter you will need to set the tran
21. ts down to 5 volts A good setting For racing or bashing in any vehicle using 8 12 NiMH or NiCad packs Option 4 6v Cuts off limits acceleration when the pack gets down to 6 volts Option 5 9v Cuts off limits acceleration when the pack gets down to 9 volts Option 6 12v Cuts off limits acceleration when the pack gets down to 12 volts 8 Motor Timing Advancing the timing on an electric motor can have varying effects Lowering the timing advance will reduce the amp draw increase runtime reduce motor battery temperature and may slightly reduce top speed and punch Raising the timing advance will increase amp draw decrease runtime increase motor battery temperature and may slightly increase top speed and punch IF you are after maximum top speed it s better to gear up to get it rather than advance the timing too far Option 1 Lowest A maximum efficiency setting giving long runtimes and cooler motor temps Very useful with high Kv low turn motors to increase motor life and reduce motor battery temperatures Option 2 Normal Default The best mix of speed punch and efficiency for all motors Option 3 Highest Increases amp draw reduces runtimes increases motor battery temperatures and may increase top speed punch slightly Use with care and monitor motor and battery temps often DO NOT use any setting above normal with 6000Kv or higher motors 9 Motor Type This setting sets which type of motor you will
22. with point and click ease Note Any mini USB cable will work with the Castle Link you do not have to buy a Castle specific USB cable Please make sure to read this manual completely to get the most from your Castle ESC A WORD ABOUT BATTERIES AND CONNECTORS As with any extremely high powered electric power system the primary limitations to ultimate vehicle performance are the batteries and connectors Use the best batteries and connectors that you can find The better the batteries the more punch you ll have Recommended capacity For 1 18th scale vehicles is 1500mah 1 10th 1 8th and 1 5th scale recommended capacity is 5000mah Do not use 20C continuous discharge batteries We recommend 30C continuous discharge or higher for 1 18th scale to 1 8th scale vehicles or high quality 25C batteries such as Traxxas Power Cells and 35C continuous or higher for 1 5th scale vehicles Using too low of a C rating or capacity will damage your ESC and will not be covered under warranty Hint Look for the batteries with the lowest resistance not necessarily the coolest labels Top of the line cells aren t required for this system to operate normally but the best cells will certainly allow your Castle system to put more power to the ground Poor quality battery connectors can be a roadblock to performance Avoid the common white plastic connectors commonly seen on many battery packs A Fast brushless setup will draw many times the
Download Pdf Manuals
Related Search