Operating Manual for the KODAK EKTAGRAPHIC III Slide Projectors
Contents
1. 19 Using a Dissolve Control 20 Shutdown EE i Saab a geod ea Cae oo eda es 20 Maintenance ses NP eae ea a ee cee een a os 21 Changing the Projection Lamp 22 Cleaning the Condenser Heat Absorbing Glass and Mirror 23 Troubleshooting 27 Warranty sesini a a etnia Rien Hebe Agee es 29 How to Obtain Service 30 Appendix A jcc Sain Pea a au dea Sw tien oa Rath wee ale et 31 Serial Number The serial number of your projector is printed on the label affixed to the power cord retainer on the base of the projector Record this number as well as the model identification date and place of purchase for future reference KODAK EKTAGRAPHIC III Slide Projector 1 Overview FRONT RIGHT 1 Tray 2 Lock Ring 3 Storage Compartment Remote 4 Elevating Foot 5 Elevating Adjustment Wheel 6 Elevating Foot Release Button 7 Lens 8 Viewer Model ATS 9 Focus Knob 10 Autofocus Models A AMT amp ATS 11 Select Bar 12 Timer Models AMT amp ATS 13 Reverse 14 Forward 15 Power Fan Half Lamp Full Lamp BACK RIGHT 16 Tray Release Latch 17 Lamp Module 18 Raised Index Mark 19 Reading Light Cover 20 Standby Light Model E Plus 21 Special Application Receptac2. Do not immerse this equipment in water or other liquids Do not disassemble this projector Use a qualified service technician when service or repair is required Incorrect reassembly can cause electric shock the next time the projector is used Use only safety electrical low voltage SELV devices The use of an accessory attachment not recommended by the manufacturer may increase risk of damage Keep the air flow vents unobstructed Save These Instructions Operating Manual KODAK EKTAGRAPHIC III Slide Projectors Congratulations You have just purchased a KODAK EKTAGRAPHIC III Slide Projector with a KODAK Extra Bright Lamp Module This new lamp module procides 30 greater light intensity so your images look brighter richer and more saturated This module features a Lamp On indicator on the lamp module door with Kodak Extra Bright Lamp Module Contents Important Safety Instructions 2 OVELVIEN sun sas en ae a ts 2 Introduction si tsar ses hee ar een rene de ee are dla se job 3 Operation s 588 508 i ere sant dames mi ae 3 ST dardi rho eens 3 Loading the Slide Tray 6 Projecting Your Slides 10 Editing Your Presentation 17 Clearing a Gate Jam 18 Using the Built In Viewer
3. A curved field lens works best for e embossed cardboard mounts Embossed mounts have beveled edges around the aperture Kodak Premium Processing and Kodak Processing labs provide embossed mounts Lens Focal Length Use the illustration on the following page to help determine the lens focal Projector Distance length and projector distance KODAK EKTAGRAPHIC III Slide Projector 15 Operation L D 75 mm 13 3 100 mm 17 7 125 mm 22 2 150 mm 26 6 175 mm 31 0 200 mm 35 4 67 D 26 6 8 1 m KODAK EKTAGRAPHIC III Slide Projector Operation Editing Your Presentation Removing the To add or remove slides in the tray you must first remove the lock ring Lock Ring Turn the ring counterclockwise and lift off Removing a Slide Rotate the tray to the slide you wish to remove Firmly press and hold down the select bar to eject the slide Adding a Slide When the lock ring is off you can add a slide to any empty slot See Front Screen Projection on page 7 Replace and secure the lock ring KODAK EKTAGRAPHIC III Slide Projector 17 Operation Clearing a Gate Jam To remove a defective slide or foreign object stuck in the projector gate you need to remove the tray e Slide the tray release latch in the direction of the arrow and e with your other hand lift off the back of the tray Tray release latch Rotate the metal plate on the b
4. power both power switches are set at fan 7 Standby light both projection lamps are SI special applications receptacle properlv installed not burned out and readv both standby lights are operational all thermal fuses are functional Special Application The special application receptacle allows additional external control and Receptacle programming capabilitv It provides 22 5 V low voltage power isolated from the main power line Use this receptacle for e automatic return to zero devices models A and E Plus e a low voltage power supply e a dark shutter switch The receptacle accepts 8 pin plugs and DIN tvpe plugs with 3 or 5 pins at 180 See Appendix A for contact identification descriptions KODAK EKTAGRAPHIC III Slide Projector 13 Operation Single Slides Selecting Slide Projection Lenses 14 A Important All equipment cables and connectors used with the special application receptacle must be assembled by qualified electronic personnel All circuits connected electrically to the projector through this receptacle must have a rating of not more than 30 V rms and must comply with Underwriters Laboratories Inc low voltage limited energy circuit requirements To project single slides slide the power switch to a half or full lamp position Remove the tray and insert a slide upside down into the projector gate Push the slide all the way down After viewing the slide press forwar
5. fading up the light beam in the other projector This eliminates a dark screen interval When using a dissolve control you need to divide your slides into two trays odd and even numbered slides The dissolve control has two connectors that plug into the remote control receptacles in the rear of two projectors Refer to your dissolve control operating manual for additional instructions and features See your dealer in Kodak products for more information on Kodak dissolve controls To shut down e remove and store the tray e slide the power switch to off Your projector will remain warm for several minutes KODAK EKTAGRAPHIC III Slide Projector Maintenance Projection Lamps Lamp Tips To ensure a long life and trouble free operation for your projector e Allow the air to flow freely around the projector e Do not recirculate warm air e Keep the projector dust free e If your projector is chilled bring it to room temperature before operating Quartz halogen 82 V projection lamps Included EXR 300 W 35 hour lamp life at full lamp medium brightness Sampling of other lamps EXY 200 hours less brightness EXW 15 hours maximum brightness FHS 70 hours medium brightness Use combinations of lamp brightness plus half and full lamp settings to approximate image brightness in multi projector presentations Desired EKTAGRPAHIC III Brightness Projector Lamp Maximum EXW High EXR Medium FHS Low EXY Proj
6. fuse is located in the small pull out storage door below the Power Inlet Simply pull the door with your finger Remove the spent fuse with a small object e g pencil tip by pushing the fuse up and removing it from the receptacle Press the spare fuse into the receptacle and close the storage door A Important The EKTAGRAPHIC III BR and ABR Slide Projectors are supplied with a 3 wire grounding power cord to comply with UL122 USA and CSA222 Canada safety and electrical standards We urge you to provide a permanent properly installed 3 wire receptacle as the source of power for this projector For advice and assistance call a licensed electrician or your local power company When used outside the United States of America please use a proper adapter that ensures grounding and polarization Although the Models III BR and ABR are approved to the standards of UL and CSA they are not intended to meet approval in all countries worldwide KODAK EKTAGRAPHIC III Slide Projector Operation Models A Open the storage compartment and remove the remote control AMT and ATS Storage compartment door Remote control Plug the 5 pin cable remote connector into the remote control receptacle aligning the raised dot with the metallic rivet head Rivet head Raised dot This receptacle also accepts plugs for accessories such as Kodak dissolve controls Plug the power cord into a grounded outlet with 110 to 125 volt 60 Hz cu
7. starting positions for multiple projector presentations For an 80 slide tray in the zero position the raised index mark is at slot 20 If you start with slide 6 it will align at slot 26 For a 140 slide tray in the zero position the index mark is at slot 35 So if you start with slide 12 it will align at slot 47 KODAK EKTAGRAPHIC III Slide Projector 9 Operation Projecting Your Slides Lens To insert a lens push the focus knob up and position the lens gear teeth on the lens barrel with the notch on the projector Lamp Slide the power switch to half lamp for longer lamp life or lamp for maximum brightness You may want to keep a spare KODAK EC Lamp Module CAT 831 3587 handy in case the lamp burns out during a presentation Replacing the entire module makes the change quick and easy See Maintenance on page 21 for instructions on changing the lamp module See your dealer in Kodak products to order this module 10 KODAK EKTAGRAPHIC III Slide Projector Operation Forward and Press the forward button on the projector or the remote control to project the Reverse first slide To change slides briefly press the forward or reverse buttons Focus Focus your first slide using the focus knob on the projector or the focus button on the remote control Autofocus On OTt SH Focus Focus Autofocus With autofocus on the projector automatically focuses each slide after you Mode
8. Operating Manual KODAK EKTAGRAPHIC III Slide Projectors PRESENTATION TECHNOLOGIES Important Safety Instructions When using your projector always follow basic safety precautions 1 Read and understand all instructions before using this equipment Operate this projector with 110 to 125 volt 60 Hz current only Incorrect voltage can cause projector malfunction See Startup on page 3 for Models III BR and II ABR which feature a multi voltage selector Close supervision is necessary when any appliance is used by or near children or others who may not understand the need for these precautions Do not leave the projector unattended during use Be careful not to touch hot parts For lamp replacement allow the module to cool before touching the lamp and the surrounding area Do not place the lamp module on heat sensitive surfaces Do not operate your projector if the cord is damaged or if the projector has been dropped or damaged see How to Obtain Service on page 30 6 Position the cord so that it is not tripped over pulled or placed in contact with hot surfaces 7 If an extension cord is necessary use a cord with a current rating at least equal to that of the projector Cords rated for less amperage than the projector may overheat Always unplug the projector from the electrical outlet before cleaning and servicing and when it is not in use Allow the projector to cool before storing
9. Vac 485 Shutter Switch Connects to an internal single pole single throw normallv closed switch Contacts are open when a slide is in the projector gate and the shutter is open These leads connect only to the switch terminals Do not exceed a switching load of 1 A at 30 Vac 7 amp 8 Low Voltage Supply For operating external equipment The current is supplied by a secondary winding on the main motor isolated from the line voltage power and is available whenever the main projector motor is running Supply is 25 5 V 500 mA 1 2 A maximum Contact number 8 is common return for the remote control circuit Contact number 7 is the hot lead and is fused with a slow blowing fuse Replacement requires disassembly of the projector by a qualified technician 6 amp 8 Forward Tray Connects to the forward tray advance circuitry in the projector These contacts are connected internally to the remote control receptacle and an electrical connection made at either receptacle will result in a forward cycle 2 amp 8 Reverse Tray Cycle Connects to the reverse tray advance circuitry in the projector These contacts are connected internally to the remote control receptacle and an electrical connection made at either receptacle will result in a reverse cycle Shell Plug Ground If a plug with a conducting shell is used it is connected to the projector frame chassis through the special application
10. d reverse or the select bar to eject the slide Select bar 2 When buying a lens consider features such as focal length measured in millimetres aperture designed as an f stop and the lens design curved or flat When selecting a lens remember that the shorter the focal length i e the smaller the f number the brighter the projected image Also a curved field lens in combination with cardboard open face mounts from an automated mounting process provide superior projection quality A flat field lens is the best choice for glass mounted slides 1 UL 122 Photographic Equipment Underwriters Laboratories Inc 33 Pfingsten Road Northbrook IL 60062 2096 CSA Specification C222 Number 118 1959 R1965 Picture Machines Appliances CSA 178 Rexdale Boulevard Rexdale Ontario M9W 1R3 Canada KODAK EKTAGRAPHIC III Slide Projector Operation Choosing a Curved The lens you select depends on how you use your projector and what type of or Flat Field Lens slide mount you use So that you may choose the lens that best meets your needs we do not include a lens with the projector To obtain the best results of a projected image insert slides with the emulsion side toward the projection lens slide curve toward the light source A flat field lens works best for general home projection glass mounts plastic mounts mixed mounts non embossed cardboard mounts rear projection applications duplicated slides
11. ector operation on line voltages above 125 volts greatly reduces the lamp life Unplug the projector before changing the lamp Allow for unrestricted flow of air to the exhaust vent to prolong lamp life Gently wipe off any fingerprints with a soft cloth moistened with rubbing alcohol KODAK EKTAGRAPHIC III Slide Projector 21 Maintenance Changing the Projection Lamp 22 Slide the power switch to Off and unplug the projector Allow the projector and lamp to cool for about 10 minutes Push the lamp module release button and remove the lamp module You can replace it with a new lamp module or replace only the lamp Note There is an additional safety latch which reduces the chance of an accident with a loosely inserted lamp module that may cause some resistance To release the latch you may need to apply extra effort when you pull out the module To replace only the lamp lift up the lamp release clip Carefully remove the worn lamp from the socket and place it on a heat resistant surface Insert a new lamp into the socket Push down to tightly seat the replacement lamp Relatch the clip in the forward position and push the lamp module all the way back into the projector until it latches Lamp release clip KODAK EKTAGRAPHIC III Slide Projector Maintenance Cleaning the Condenser Heat Absorbing Glass and Mirror To clean the condenser heat absorbing glass or mirror you must disasse
12. flat field lens plastic or non embosssed mounts See Choosing a Curved or Flat Field Lens on page 15 Curved field lens used for rear Use a flat field lens projection Autofocus motor runs continuously Glass slides in tray Turn off autofocus or use slides with mounts other than glass Autofocus fails to operate Lamp performance Install new lamp and try autofocus again KODAK EKTAGRAPHIC III Slide Projector 27 Troubleshooting PROBLEM CAUSE CORRECTION Slide fails to drop into projection position Tray base plate not properly indexed Rotate the tray base plate until it locks into position Tray not properly positioned on projector Reposition tray on projector Slide mount warped or frayed at corners slide Straighten mount or remount slide Projector not level or tilted too high Set projector on a stand equal with center of screen Uneven illumination on screen Projection lamp not fully seated Check lamp Condenser lens not installed or not positioned properly in mount Check condenser lens Slide mount not seated properly in projector gate Check slide position and slide mount condition Projector won t cycle to next slide Tray not properly positioned Reposition tray Slide or foreign object stuck in gate See Clearing a Gate Jam on page 18 Program does not start with the with the correct slide Tray number i
13. le 22 Remote Receptacle BASE 23 Power Cord 24 Power Cord Retainer 25 Leveling Foot KODAK EKTAGRAPHIC III Slide Projector Introduction Operation Startup Models III BR and ABR Only Take the time to read the instructions in this operating manual to become familiar with your KODAK EKTAGRAPHIC III Slide Projector and how to operate it properly A Important Before you turn on your new KODAK EKTAGRAPHIC III BR or ABR Slide Projector it is critical to set the voltage selector to the proper setting Use the proper fuse for the voltage selection See the fuse label on the back of the projector The voltage selector on the KODAK EKTAGRAPHIC III BR or ABR Slide Projector is located on the base of the projector Using a small object such as a coin you can set the voltage selector for the proper voltage 100 115 130 220 230 and 240 V Fuse Storage Door Power Cord Retainer Volta Selector Power Inlet KODAK EKTAGRAPHIC III Slide Projector 3 Operation EKTAGRAPHIC III BR and ABR Slide Projectors have a sensing capability to automatically set the proper power cycle 50 or 60 Hz This eliminates the need to manually change the two position switch included on models manufactured before November 1996 These projectors are shipped with a detachable power cord that is packaged separately not wound on the Power Cord Retainer A spare fuse is provided The
14. ls A AMT focus your first slide manually Turn autofocus off if glass slides make the and ATS only autofocus motor run continuously Random Projection For random projection of any slide in the tray e press and hold down the select bar e rotate the tray to the desired slide and e release the select bar A Select bar KODAK EKTAGRAPHIC III Slide Projector 11 Operation Screen Image Use the elevating foot to horizontally center the projected image on the screen To release the foot press the release button while lifting the front of the projector to the desired height Use the elevating wheel to make fine adjustments Elevating wheel _ Elevating foot If the image is not level make an adjustment by turning the leveling foot at the rear of the projector Leveling foot Timer To time your slides use the timer switch for slide changes from 3 to Models AMT amp ATS 22 seconds only To interrupt the timer press either the forward or reverse button For manual operation slide the timer switch to Off 3 seconds 22 seconds 12 KODAK EKTAGRAPHIC III Slide Projector Operation Reading Light To illuminate a small area for reading lift the reading light cover while the projector lamp is on Reading light Standby Light A glowing standby light indicates a Model E Plus only ready condition In a dissolve program it indicates that e both projectors are receiving
15. mble the lamp module Slide the power switch to Off and unplug the projector Allow the projector to cool about 10 minutes Push the lamp module release button and remove the lamp module Use a torx head screwdriver to remove the screw Using a flat blade screwdriver apply ample pressure to release each of the metal tabs Lift off the top of the lamp module KODAK EKTAGRAPHIC III Slide Projector 23 Maintenance Condenser Lens You can clean the condenser lens in place or by pulling it out Wear gloves to prevent fingerprints LL Condenser lens Caution Heat Absorbing The heat absorbing glass is fragile Handle it only when cool Glass The heat absorbing glass easily removes for cleaning Models without KODAK Extra Bright Clean both sides of the condenser lens and the heat absorbing glass with a Lamp Module soft lint free cloth Do not leave fingerprints Replace the lens and heat absorbing glass to their original locations Heat absorbing glass 24 KODAK EKTAGRAPHIC III Slide Projector Maintenance Reassem bling the To reassemble the lamp module you will need to align and insert each tab Lamp Module into its appropriate slot Start with the tabs in the rear of the lamp module Insert the remainder of the tabs into slots until all 7 tabs on the top and 2 on the bottom are secured Insert the screw and tighten Then insert and seat the lamp KODAK EKTAGRAPHIC III Slide Pr
16. ner of the film s shiny side Insert your first slide into the first slot in the tray so that the number is visible on the outer circumference of the tray Insert your second slide in the second slot with the emulsion dull side facing your first slide and so on Front Projection KODAK EKTAGRAPHIC III Slide Projector 7 Operation Rear Screen Projection With a Dissolve Control Replace the lock ring by turning it clockwise until it is secure You can easily adapt a show from front to rear screen projection Remove each slide from the tray and turn it around keeping the slide upside down This will give the projected slide a mirror image on the screen ca IN Front Rear Projection Projection Insert your first slide back into the first slot in the tray The number is now visible in the inner circumference of the tray Replace the lock ring by turning it clockwise until it is secure When you use a dissolve control put your slides into two trays one for odd and one for even numbered slides KODAK EKTAGRAPHIC III Slide Projector Operation Tray Place the loaded slide tray on the projector Align the tray index bar with the gate index The tray will drop into position Removing the Tray To remove the slide tray Tray Index bar e press the select bar all the way down align the tray index bar with the gate index Raised Index Mark This feature allows you to coordinate tray
17. ojector 25 Maintenance Mirror To clean the mirror invert the lamp module to reach the mirror Gently clean the mirror with a soft lint free cloth moistened with lens cleaner Mirror When your maintenance is complete push the lamp module back into the projector Thermal Fuses Your projector has two thermal fuses that prevent overheating If your projector will not operate call the Kodak Information Center or Kodak in your country to obtain the name of a service center nearest you see How to Obtain Service on page 30 26 KODAK EKTAGRAPHIC III Slide Projector Troubleshooting Consult this guide before calling for service PROBLEM CAUSE CORRECTION Projector does not operate No power to projector Plug power cord into suitable electrical outlet Set power switch to Lamp No illumination on screen with slide in Power switch on Off or Fan Set switch to Lamp projector gate Lamp burned out Install new lamp or lamp module Lamp not seated in socket Check lamp Slide not in proper focus on screen Slide itself not sharp Examine slide for proper focus focus First slide in tray not properly Focus center of first slide Slide in different type of mount from Focus manually others Projection lens installed improperly Read and follow the instructions for installing the lens Uneven edge to edge focus Slide itself is not sharp Examine slide Curved field lens used with glass Try a
18. or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state KODAK EKTAGRAPHIC III Slide Projector 29 How to Obtain Service Assistance U S 1 800 242 2424 Canada 1 800 465 6325 www kodak com go projectors To obtain service or for assistance in using your KODAK EKTAGRAPHIC Slide Projector contact the Kodak Information Center at 1 800 242 2424 Monday through Friday 8 a m to 8 p m Eastern time In Canada call 1 800 465 6325 Monday through Friday 8 30 a m to 5 p m Eastern time Or call Kodak in your country Shipping To help us get your KODAK EKTAGRAPHIC Slide Projector back to you Instructions promptly please enclose a note giving details of the problem dated proof of purchase and your complete name and shipping address Pack the unit in a sturdy carton with ample packing material to protect the unit during shipping and handling 30 KODAK EKTAGRAPHIC III Slide Projector Appendix A Special Application Receptacle Identification Chart Contacts Function Description 1 amp 3 Zero Position Switch Models A and E Plus Connects to an internal single pole single throw normally open switch Contacts are closed when the slide tray is at any position other than zero These leads connect only to the switch terminals Do not exceed a switching load of 1 A at 30
19. ottom of the tray until it locks into position For a 140 slide tray see Loading the Slide Tray on page 6 Put the tray aside Remove the slide or object from the projector gate by pressing the forward button or removing the slide manually Remount damaged slides to protect your projector and slides from subsequent damage 18 KODAK EKTAGRAPHIC III Slide Projector Operation Using the Built In Viewer Model ATS Only A Important Before opening the viewer you must remove the projection lens from the projector Removing the Turn the focus knob to the horizontal position Push the knob toward the top Lens of the projector as you withdraw the lens Focus knob Lari Opening the Grasp the viewer handle and pull it out from the base of the projector It will Viewer pop into place Slide the power switch to lamp to project your slides Closing the Viewer To close the viewer fold it and push it back into the body of the projector KODAK EKTAGRAPHIC III Slide Projector 19 Operation Reinserting the Lens To reinsert the lens push the focus knob up and position the lens gear teeth on the lens barrel with the notch on the projector Focus knob Z Notch Lens gear teeth Using a Dissolve Control Shutdown 20 One of the more common uses for a dissolve control is a simple two projector fade This feature fades down the light beam in one projector while changing the image and
20. receptacle and to earth ground through the projector s power cable KODAK EKTAGRAPHIC III Slide Projector 31 PRESENTATION TECHNOLOGIES Part No 5B905 12 98 Revision EastmanKodak Company Printed In U S A Presentation Technologies EASTMAN KODKCOMPANY Rochester New York 14650 www kodak com go projectors Kodak Ektagraphic and kodalux are trademarks K
21. rrent only KODAK EKTAGRAPHIC III Slide Projector 5 Operation Loading the Slide Tray A KODAK EKTAGRAPHIC Universal Slide Tray is designed to hold up to 80 slides Be sure that your slide mounts are in good condition frayed or bent mounts may fail to drop into the projector A variety of slide trays are available with capacity up to 140 slides See your dealer in Kodak products for a complete list of Kodak trays and accessories Note Do not attempt to project slides mounted with sticky or loose tape Place the tray over the center post of the projector Align the 0 slot with the gate index the tray will drop into position If your 80 slide tray does not drop easily rotate the metal plate on the bottom of the tray until it locks into position For a 140 slide tray secure the lock ring invert the tray and align the index hole with the index notch Slide and hold the tray release latch in the direction of the arrow and turn the bottom plate until the index hole and notch align Then release the latch ly ll Index notch index 80 Slide Tray 140 Slide Tray KODAK EKTAGRAPHIC III Slide Projector Operation Front Screen Remove the lock ring by turning it counterclockwise and lifting it off Projection Lock ring Check each slide s orientation horizontal or vertical and arrange them in the order you wish to show them Then turn the slides upside down Number each mount in the upper right hand cor
22. s not aligned with the with the raised index mark Reposition tray see Tray on page 9 28 KODAK EKTAGRAPHIC III Slide Projector Warranty Limitations Your Rights Under State Law Kodak warrants this KODAK EKTAGRAPHIC Slide Projector to function properly for four years from the date of purchase If this KODAK EKTAGRAPHIC Slide Projector does not function properly within the warranty period upon submission of dated proof of purchase Kodak will repair it without charge except for worn out projector lamps If Kodak is unable to repair the projector the option of replacement or refund of the purchase price will be available See an audiovisual products dealer in your country for the KODAK EKTAGRAPHIC III ABR Slide Projector s warranty coverage This warranty does not cover circumstances beyond Kodak s control projector lamps or problems caused by failure to follow the care and operating instructions in the manual Any modification to the original design of this projector nullifies this warranty Warranty service will not be provided without dated proof of purchase Kodak makes no other express warranty for this product Repair or replacement is Kodak s only obligation Kodak will not be responsible for any consequential or incidental damages resulting from the sale or use of this projector regardless of the cause of such damages Some states do not allow the exclusion or limitation of incidental
Download Pdf Manuals
Related Search