USER`S MANUAL - Pdfstream.manualsonline.com
Contents
1. Square Inner Caps 32 and two 1 Round Inner Caps 49 into the Arm Frame 52 Lubricate the upper axle on the Arm Frame 52 Hold the axle between the two Arm Frame Bushings 68 Set the Arm Frame Bushings and the Arm Frame on the welded plate on the Top Frame 67 Place the Arm Frame Bracket 69 over the Arm Frame Bushings Attach the Arm Frame Bracket to the Top Frame with four 1 4 x 1 2 Screws 31 and 1 4 Nylon Jam Nuts 86 The indicated bracket on the Arm Frame must face forward Lubricate 68 8 10 11 Press a 1 3 4 Square Inner Cap 44 into each end of an Arm 46 Apply lubricant to the lower axles on the Arm Frame 52 Slide an Arm 46 onto one of the axles Hold two 1 Retainers 54 and a 1 Round Cover Cap 55 against the lower end of the axle The teeth on the Retainers must bend toward the Round Cover Cap see the inset drawing Tap the Retainers and Round Cover Cap onto the axle Assemble the other Arm 46 to the Arm Frame 52 in the same manner 12 Insert the two 4 1 2 L Pins 60 down through the indicated holes in the Arm Frame 52 and the Arms 46 13 Wet both Arms 46 with soapy water Slide a 7 3 4 Pad 45 onto each Arm Press a 1 Round Inner Cap 49 into the indicated end of a 7 Handle 47 Insert the Handle into one of the Arms 46 Attach the Handle with a 5 12. U Bracket 12 2 Handgrip 57 1 1 1 4 Square Inner Cap 13 1 Seat 58 2 Narrow Swivel Bracket 14 1 5 16 x 2 3 4 Carriage Bolt 59 2 Cable Trap 15 5 3 1 2 Pulley 60 2 4 1 2 L Pin 16 1 3 8 x 3 1 2 Bolt 61 1 5 16 x 2 Bolt 17 1 5 16 x 3 Bolt 62 1 5 16 x 2 Eyebolt 18 2 1 4 x 3 4 Screw 63 1 Stop Bracket 19 2 Weight Bumper 64 1 1 Plastic Stop 20 1 1 4 x 2 Screw 65 6 1 2 x 1 2 Spacer 21 4 3 8 Nylon Locknut 66 1 Long Cable 22 1 1 Metal Spacer 67 1 Top Frame 23 1 Short Cable 68 2 Arm Frame Bushing 24 2 5 16 x 1 1 2 Bolt 69 1 Arm Frame Bracket 25 6 Weight 70 3 3 8 x 2 3 4 Bolt 26 1 Weight Pin 71 1 Stabilizer 27 3 2 Square Inner Cap 72 2 Weight Guide 28 2 Pad Tube 73 2 1 2 x 3 4 Spacer 29 1 Leg Lever 74 1 5 16 x 6 Bolt 30 4 Pad 75 1 Adjustment U Bracket 31 4 1 4 x 1 2 Screw 76 1 V Pulley 32 4 1 1 2 Square Inner Cap 77 1 Top Weight 33 5 5 16 x 2 1 4 Bolt 78 2 P Plate 34 4 3 4 Round Inner Cap 79 1 Weight Tube Bumper 35 1 5 16 x 3 1 4 Bolt 80 1 Weight Tube 36 1 Seat Frame 81 2 4 1 2 Pulley 37 1 Seat Plate 82 1 Large Cable Trap 38 1 1 4 x 2 Carriage Bolt 83 2 Cable Clip 39 1 Nylon Strap 84 1 Chain 40 1 Seat Knob 85 1 Lat Bar 41 1 Backrest 86 4 1 4 Nylon Jam Nut 42 1 Front Upright 87 1 5 16 x 3 1 2 Bolt 43 2 1 4 x 2 1 2 Screw 88 4 2 Square Outer Cap 44 6 1 3 4 Square I
3. WARNING To reduce the risk of serious injury read the following important precautions before using the home gym system 1 Itis the responsibility of the owner to ensure that all users of the home gym system are adequately informed of all precautions 8 Always stand on the foot plate when per forming an exercise that could cause the home gym system to tip 2 Read all instructions in this manual and in 9 The home gym system is intended for use by only one person at a time the maximum user weight is 250 pounds Make sure that the cables remain on the pul leys at all times If the cables bind while you are exercising stop immediately and make sure that the cables are on all of the pulleys 10 the accompanying literature before using the home gym system Use the home gym system only on a level surface Place a mat beneath the home gym system to protect the floor or carpet Inspect and tighten all parts often Replace any worn parts immediately 11 Always disconnect the lat bar from the home gym system when performing an exercise Keep children under 12 and pets away from that does not use the lat bar the home gym system at all times 12 If you feel pain or dizziness at any time while Never release the arms leg lever lat bar or exercising stop immediately and begin cool nylon strap while weights are raised The ing down weights will fall with great force 13 The home gym system is intended for home use
4. MAINTENANCE Inspect and tighten all parts each time you use the home gym system Replace any worn parts immediately The home gym system can be cleaned using a damp cloth and mild non abrasive detergent Do not use solvents TIGHTENING THE CABLES Adjustment Woven cable the type of cable used on the home gym Screw system can stretch slightly when it is first used If there is slack in the cables before resistance is felt the cables should be tightened Locate the adjustment e Adjustment sleeve and adjustment screw near the lower end of the d Sleeve Short Cable 23 Loosen the adjustment screw Pull the end of the Short Cable until there is no slack Slide the adjustment sleeve and the ball against the indicat ed 3 1 2 Pulley 15 Retighten the adjustment screw Make sure that the cables are not too tight or the top weight will be lifted off the weight stack 19 04983 Key No Qty Description Key No Qty Description 1 4 5 16 x 2 1 2 Carriage Bolt 46 2 Arm 2 2 5 16 Nylon Jam Nut 47 2 7 Handle 3 21 5 16 Nylon Locknut 48 6 3 8 x 1 3 4 Bolt 4 1 Base 49 6 1 Round Inner Cap 5 7 3 8 Nylon Jam Nut 50 1 3 8 x 2 1 4 Bolt 6 1 Support Plate 51 2 1 2 x 3 8 Spacer 7 1 1 4 Nylon Locknut 52 1 Arm Frame 8 16 5 16 Flat Washer 53 2 Plastic Bushing 9 5 3 8 Flat Washer 54 4 1 Retainer 10 4 1 4 Flat Washer 55 2 1 Round Cover Cap 11 5 5 16 x 2 3 4 Bolt 56 2 Large
5. Seat Frame with a 5 16 x 2 3 4 Carriage Bolt 14 and the Seat Knob 40 28 Press 3 4 Round Inner Caps 34 into the ends of a Pad Tube 28 Insert the Pad Tube into the Seat Frame 36 Slide a Pad 30 onto each end of the Pad Tube Press 3 4 Round Inner Caps 34 into the ends of the other Pad Tube 28 Insert the Pad Tube into the Leg Lever 29 Slide a Pad 30 onto each end of the Pad Tube 14 29 Slide a Handgrip 12 onto each end of the Lat Bar 85 30 Make sure that all parts are properly tightened The use of all remaining parts will be explained in ADJUST MENT beginning on page 16 of this manual Before using the home gym system pull each cable a few times to make sure that the cable moves smoothly over the pulleys If one of the cables does not move smoothly locate and correct the problem before using the home gym system IMPORTANT If the cables are not properly routed they may be damaged when heavy weight is used See the CABLE DIAGRAMS on page 22 of this manual 15 ADJUSTMENT The instructions below describe how each part of the home gym system can be adjusted Refer to the EXERCISE GUIDE accompanying this manual to see how the home gym system should be set up for each exercise IMPORTANT When attaching the lat bar or nylon strap make sure that the attachments are in the correct starting position for the exercise to be performed If there is any slack in the cable or chain as an exerci
6. to achieve the specific results you want For your safety and benefit read this manual care fully before using the WEIDER 8507 Training System If you have additional questions please call ASSEMBLED DIMENSIONS Height 77 in Width 39 in Length 48 in Backrest Weight Stack Weight Pin ASSEMBLY Assembly requires two people Due to the size Tighten all parts as you attach them unless and weight of the home gym system assemble it in instructed to do otherwise the location where it will be used THE FOLLOWING TOOLS NOT INCLUDED ARE Place all parts of the home gym system in a REQUIRED FOR ASSEMBLY cleared area and remove the packing materials do not dispose of the packing materials until Two 2 adjustable wrenches A lt One 1 phillips screwdriver assembly is completed Before beginning read each assembly step and look at each drawing carefully One 1 rubber mallet For help identifying small parts used in assembly Lubricant such as grease or petroleum jelly refer to the PART IDENTIFICATION CHART and soapy water are also required attached to the center of this manual To simplify assembly the following tools are recom e During assembly be sure that all parts are orient mended A socket set open or closed wrenches or ed as shown in the drawings ratchet wrenches 1 Before you begin make sure that you have carefully read the instructions a
7. with the use or performance of the product or damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyment or use costs of removal installation or other con sequential damages of whatsoever nature Some states do not allow the exclusion or limitation of inci dental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state to state ICON HEALTH amp FITNESS INC 1500 S 1000 W LOGAN UT 84321 9813 Part No 145637 H00715 C 0498 Printed in Canada 1998 ICON Health amp Fitness Inc
8. 6 x 2 1 4 Bolt 33 two 5 16 Flat Washers 8 a 1 2 x 3 8 Spacer 51 and a 5 16 Nylon Locknut 3 Attach a 7 Handle 47 to the other Arm 46 in the same manner 14 Attach a Large U Bracket 56 to one of the Arms 46 with a 3 8 x 2 3 4 Bolt 70 3 8 Flat Washer 9 and 3 8 Nylon Locknut 21 Be sure that the Swivel Bracket 58 is on the inside as shown Do not overtighten the 3 8 Nylon Locknut Attach a Large U Bracket 56 to the other Arm 46 in the same manner 15 IMPORTANT As you assemble the Long Cable 66 and the Short Cable 23 refer to the CABLE DIAGRAMS on page 22 of this manual to make sure that the Cables are properly routed Find the end of the Long Cable 66 that does not have a rubber ball Insert that end of the Long Cable up through the indicated opening in the Top Frame 67 Lay the Long Cable 66 over a 4 1 2 Pulley 81 Attach the Pulley inside the Top Frame 67 with a 3 8 x 2 3 4 Bolt 70 two 3 8 Flat Washers 9 the two 1 2 x 1 2 Spacers 65 and a 3 8 Nylon Locknut 21 16 Remove the 3 8 x 1 3 4 Bolt 48 3 8 Nylon Jam Nut 5 and 3 1 2 Pulley 15 from the indicated bracket on the Top Frame 67 Insert the end of the Long Cable 66 through the bracket and down through the indicated hole Re attach the 3 1 2 Pulley 15 to the brack
9. 9 Model No WESY85070 Serial No Write the serial number in the space above for future reference QUESTIONS As a manufacturer we are committed to providing complete customer satisfaction If you have questions or if there are missing or damaged parts we will guarantee complete satisfac tion through direct assistance from our factory TO AVOID UNNECESSARY DELAYS PLEASE CALL DIRECT TO OUR TOLL FREE CUSTOMER HOT LINE The trained techni cians on our customer hot line will provide immediate assis tance free of charge to you CUSTOMER HOT LINE 1 800 999 3756 Mon Fri 6 a m 6 p m MST CAUTION Read all precautions and instruc I tions in this manual before using U S E R 5 M AN UA L this equipment Save this manual for future reference TABLE OF CONTENTS IMPORTANT PRECAUTIONS cirie A aie ea aa E a 2 BEFORE YOU BEGIN suit oe gta od bee a a ala kana a ead tao dodo eh ena MGM ieee as 3 ASSEMBLY cana tada BAY Bonet did A Sheena MMe eee ia See on cai he ae 4 ADJUSTMENT gt be awe age beatae AO e a i aes eee a 16 TROUBLE SHOOTING AND MAINTENANCE 19 7 20 EXPLODED DRAWING gt suso asia ada a a Aa Ai ie 21 CABLE DIAGRAMS Ai ea a i A a A 22 ORDERING REPLACEMENT PARTS Back Cover Note A PART IDENTIFICATION CHART is attached to the center of this manual Remove the PART IDENTIFI CATION CHART before beginning assembly IMPORTANT PRECAUTIONS
10. ANN E 5 16 x 2 Bolt 61 NAN 5 16 x 2 1 4 Bolt 33 A 3 8 x 1 3 4 Bolt 48 AY 8 3 8 x 2 1 4 Bolt 50 CUI 1 4 x 2 Carriage Bolt 38 Pe O H 1 4 Nylon Locknut 7 VNS O H 1 4 Nylon Jam Nut 86 O 5 16 Jam Nut 2 YA O H 5 16 Nylon Locknut 3 3 8 Nylon Jam Nut 5 3 8 Nylon Locknut 21 1 4 Flat Washer 10 5 16 Flat Washer 8 3 8 Flat Washer 9 Ol e o OLI 1 2 x 3 8 Spacer 51 OL 1 2 x 1 2 Spacer 65 OL 1 2 x 3 4 Spacer 73 OL 1 Metal Spacer 22 1 Plastic Stop 64 5 16 2 1 2 Carriage Bolt 1 5 16 2 3 4 Carriage Bolt 14 AM 5 16 x 2 3 4 Bolt 11 NAN a 3 8 x 2 3 4 Bolt 70 5 16 x 3 Bolt 17 0 5 16 3 1 4 Bolt 35 1 5 16 3 1 2 Bolt 87 AN i 3 8 x 3 1 2 Bolt 16 AM 5 16 6 Bolt 74 ORDERING REPLACEMENT PARTS To order replacement parts simply call our Customer Service Department toll free at 1 800 999 3756 Monday through Friday 6 a m until 6 p m Mountain Time excl
11. et on the Top Frame 67 with the 3 8 x 1 3 4 Bolt 48 and 3 8 Nylon Jam Nut 5 Be sure that the Long Cable is between the Pulley and the top of the bracket 17 Wrap the Long Cable 66 around the V Pulley 76 Attach the Pulley and a Large Cable Trap 82 to the welded bracket on the Top Frame 67 with a 3 8 x 2 1 4 Bolt 50 and 3 8 Nylon Jam Nut 5 Be sure that the Large Cable Trap is turned to the indicated position 18 Note The 3 1 2 Pulley 15 used in this step is pre assembled It is shown removed for easier part identification Route the Long Cable 66 around the 3 1 2 Pulley 15 on the left Arm 46 Tighten the 3 8 Nylon Jam Nut 5 and 3 8 x 1 3 4 Bolt 48 Be sure that the Cable Trap 59 is oriented as shown 10 19 Note The 4 1 2 Pulley 81 shown in this step is pre attached to the Adjustment U Bracket 75 Remove the 3 8 x 1 3 4 Bolt 48 3 8 Nylon Locknut 21 and 4 1 2 Pulley 81 from the Adjustment U Bracket 75 Attach the Adjustment U Bracket 75 to the Front Upright 42 with the 5 16 x 3 1 4 Bolt 35 a 5 16 Flat Washer 8 and a 5 16 Nylon Locknut 3 Thread the Nylon Locknut onto the Bolt until the first two threads of the Bolt are through the Nylon Locknut Wrap the Long Cable 66 around the 4 1 2 Pulley 81 as shown Re attach the Pulley
12. nner Cap 1 User s Manual 45 2 7 3 4 Pad PART LIST Model No WESY85070 Note indicates a non illustrated part Specifications are subject to change without notice See the back cover of the user s manual for information about ordering replacement parts 20 EXPLODED DRAWING Model No WESY85070 RO498A CABLE DIAGRAMS The cable diagrams below show the proper routing of the Short Cable 23 and the Long Cable 66 Use the diagram to make sure that the two cables are assembled correctly The numbers show the routing of each cable Long Cable 66 Short Cable 23 Weight Stack 1 22 3 4 Round Inner Cap 34 1 Round Inner Cap 49 1 Round Cover Cap 55 a N MY 5 16 2 Eyebolt 62 N 1 1 4 Square Inner Cap 57 4 N 4 N NG A 1 1 2 Square Inner Cap 32 1 3 4 Square Inner Cap 44 4 9 NG 2 Square Inner Cap 27 MY Ne J 2 Square Outer Cap 88 MM CMM 1 4 x 1 2 Screw 31 1 4 x 3 4 Screw 18 CMM 1 4 x 2 Screw 20 1 4 x 2 1 2 Screw 43 aM 5 16 1 1 2 Bolt 24
13. only Do not use the home gym system in any commercial rental or institutional setting Keep hands and feet away from moving parts Always wear athletic shoes for foot protection WARNING Before beginning this or any exercise program consult your physician This is especially important for persons over the age of 35 or persons with pre existing health problems Read all instructions before using ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product our Customer Service Department toll free at 1 800 999 3756 Monday through Friday 6 a m until 6 p m Mountain Time excluding holidays To help us assist you please note the product model number and serial number before calling The model number is WESY85070 The serial number can be found on a decal attached to the WEIDER 8507 see the front cover of this manual Before reading further please look at the drawing below and familiarize yourself with the parts that are labeled High Pulley Station Lat Bar Arms Leg Lever Low Pulley Station Foot Plate BEFORE YOU BEGIN Thank you for selecting the versatile WEIDER 8507 Training System The WEIDER 8507 offers an impres sive array of weight stations designed to develop every major muscle group of the body Whether your goal is to tone your body build dramatic muscle size and strength or improve your cardiovascular system the WEIDER 8507 will help you
14. ot attached to the leg lever Next remove the Seat Knob 40 and 5 16 x 2 3 4 Carriage Bolt 14 from the Seat Frame 36 Lift the Seat Frame off the Front Upright 42 ATTACHING THE LEG LEVER TO THE LOW PULLEY STATION To use the Leg Lever 29 the seat must be attached to the front upright see ATTACHING AND REMOVING THE SEAT on page 13 Attach the Chain 84 between the Short Cable 23 and the 5 16 x 2 Eyebolt 35 on the Leg Lever with two Cable Clips 83 ATTACHING THE LAT BAR OR NYLON STRAP TO THE HIGH PULLEY STATION Attach the Lat Bar 85 to the Long Cable 66 with a Cable Clip 83 For some exercises the Chain 84 should be attached between the Lat Bar and the Long Cable with two Cable Clips Adjust the length of the Chain between the Lat Bar and the Long Cable so the Lat Bar is in the correct starting position for the exercise to be performed The Nylon Strap 39 can be attached in the same man ner 17 18 ATTACHING THE LAT BAR OR NYLON STRAP TO THE LOW PULLEY STATION Attach the Lat Bar 85 to the Short Cable 23 with a Cable Clip 83 For some exercises the Chain 84 should be attached between the Lat Bar and the Short Cable with two Cable Clips Adjust the length of the Chain between the Lat Bar and the Short Cable so the Lat Bar is in the correct starting position for the exercise to be performed The Nylon Strap 39 can be attached in the same manner TROUBLE SHOOTING AND
15. pright 42 with a 3 8 x 3 1 2 Bolt 16 a 3 8 Washer 9 anda 3 8 Nylon Jam Nut 5 Be sure that the Short Cable is between the Pulley and the Metal Spacer 24 Attach the Backrest 41 to the Front Upright 42 with two 1 4 x 2 1 2 Screws 43 and 1 4 Flat Washers 10 25 Press a 1 1 2 Square Inner Cap 32 into the Seat Frame 36 Insert the 1 4 x 2 Carriage Bolt 38 into the center hole in the Seat Plate 37 Attach the Seat Plate to the Seat 13 with two 1 4 x 3 4 Screws 18 Insert the 1 4 x 2 Carriage Bolt 38 into the indi cated hole in the Seat Frame 36 Tighten a 1 4 Nylon Locknut 7 with a 1 4 Flat Washer 10 onto the Carriage Bolt Attach the other end of the Seat 13 to the Seat Frame 36 with a 1 4 Flat Washer 10 and the 1 4 x 2 Screw 20 13 26 Press a 1 1 2 Square Inner Cap 32 into the Leg Lever 29 Attach the 5 16 x 2 Eyebolt 62 to the Leg Lever 29 with a 5 16 Flat Washer 8 and a 5 16 Nylon Locknut 3 Lubricate a 5 16 x 2 1 4 Bolt 33 Attach the Leg Lever 29 to the Seat Frame 36 with the Bolt and a 5 16 Nylon Locknut 3 Do not overtighten the Nylon Locknut the Leg Lever must be able to pivot freely 27 Set the bracket on the Seat Frame 36 onto the indicated pin on the Front Upright 42 Attach the
16. se is performed the effectiveness of the exercise will be reduced CHANGING THE WEIGHT SETTING To change the weight setting insert the Weight Pin 26 under one of the Weights 25 Make sure to insert the Weight Pin until the bent end of the Weight Pin is touch ing the Weights and turn the bent end downward The weight setting can be changed from 6 pounds to 81 pounds in increments of 12 5 pounds Note Due to the cables and pulleys the actual amount of resis tance at each exercise station will vary from the weight setting SWITCHING THE ARMS TO THE PRESS MODE OR THE BUTTERFLY MODE To perform the BENCH PRESS exercise switch the Arms 46 to the press mode by inserting the two 4 1 2 L Pins 60 down through the indicated holes in the Arm Frame 52 and the Arms To perform the BUTTERFLY exercise switch the Arms 46 to the butterfly mode by inserting one of the 4 1 2 L Pins 60 down through the hole in the center of the Arm Frame 52 and the Stop Bracket not shown Set the other L Pin aside 16 ATTACHING AND REMOVING THE SEAT Set the bracket on the Seat Frame 36 on the indicated pin on the Front Upright 42 Attach the Seat Frame to the Front Upright with the 5 16 x 2 3 4 Carriage Bolt 14 and Seat Knob 40 For some exercises the Seat 13 must be removed First make sure that the chain is n
17. t the top of this page Press a 2 Square Outer Cap 88 onto each end of the Stabilizer 71 Press a 2 Square Outer Cap onto each side of the Base 4 Press a 2 Square Inner Cap 27 into the end of the Base Insert two 5 16 x 2 1 2 Carriage Bolts 1 up through the Stabilizer 71 Insert two 5 16 x 2 1 2 Carriage Bolts up through the Base 4 Slide the indicated end of the Base 4 onto the 5 16 x 2 1 2 Carriage Bolts 1 in the Stabilizer 71 Tighten a 5 16 Nylon Locknut 3 onto each Carriage Bolt 2 Settwo Weight Bumpers 19 onto the Base 4 as shown Slide the Weight Guides 72 into the Base 4 Attach each Weight Guide to the Base with a 5 16 x 2 3 4 Bolt 11 two 5 16 Washers 8 two 1 2 x 1 2 Spacers 65 and a 5 16 Nylon Locknut 3 3 Slide six Weights 25 on the Weight Guides 72 Be sure that all of the Weights are turned so the pin grooves are on the indicated side Pin Grooves 4 Press the 1 1 4 Square Inner Cap 57 into the Front Upright 42 Attach the 1 Plastic Stop 64 to the center hole in the Stop Bracket 63 with a 5 16 x 1 1 2 Bolt 24 and 5 16 Nylon Locknut 3 Attach the Stop Bracket 63 to the Front Upright 42 with a 5 16 x 2 Bolt 61 5 16 Flat Washer 8 and 5 16 Nylon Locknut 3 Slide the Front Upright 42 onto the two 5 16 x 2 1 2 Carriage Bolts 1 in
18. the Base 4 Thread two 5 16 Nylon Locknuts 3 onto the Carriage Bolts Do not tighten the Nylon Locknuts yet 5 Press the Weight Tube Bumper 79 into the end of the Weight Tube 80 Slide the Top Weight 77 onto the Weight Tube Be sure that the pins on the Weight Tube are resting in the pin grooves under the Top Weight Locate the Short Cable 23 Attach the Short Cable to the Weight Tube 80 with a 5 16 x 1 1 2 Bolt 24 and a 5 16 Nylon Locknut 3 6 Lubricate the insides of the holes in the Top Weight 77 Slide the Top Weight onto the stack of Weights 25 Lubricate 7 Press two 2 Square Inner Caps 27 into the Top Frame 67 Attach the Top Frame 67 to the Front Upright 42 with two 5 16 x 2 3 4 Bolts 11 the Support Plate 6 and two 5 16 Nylon Locknuts 3 Do not tight en the Nylon Locknuts yet Attach the Top Frame 67 to the Stop Bracket 63 with a 5 16 x 2 3 4 Bolt 11 5 16 Flat Washer 8 and 5 16 Nylon Locknut 3 Do not tighten the Nylon Locknut yet Attach the upper ends of the Weight Guides 72 to the Top Frame 67 with the 5 16 x 6 Bolt 74 two 1 2 x 3 4 Spacers 73 and a 5 16 Nylon Locknut 3 Tighten all Nylon Locknuts used in steps 4 through 8 Press two 1 3 4 Square Inner Caps 44 two 1 1 2
19. to the Adjustment U Bracket 75 with the 3 8 x 1 3 4 Bolt 48 and 3 8 Nylon Locknut 21 20 Note The 3 1 2 Pulley 15 used in this step is pre assembled It is shown removed for easier part identification Route the Long Cable 66 around the 3 1 2 Pulley 15 on the right Arm 46 Tighten the 3 8 Nylon Jam Nut 5 and 3 8 x 1 3 4 Bolt 48 Be sure that the Cable Trap 59 is oriented as shown 11 21 Attach the 5 16 3 Bolt 17 two 5 16 Flat Washers 8 and a 5 16 Jam Nut 2 to the indicat ed hole in the Top Frame 67 Slide the end of the Long Cable 66 onto the 5 16 x 3 Bolt 17 Tighten another 5 16 Jam Nut 2 onto the Bolt Note The 5 16 Jam Nut should not be fully tightened against the end of the Cable There must be enough room between the Jam Nuts for the end of the Cable to pivot 22 Assemble the two I Plates 78 two 3 1 2 Pulleys 15 the Long Cable 66 and the Short Cable 23 with two 3 8 x 1 3 4 Bolts 48 and 3 8 Nylon Jam Nuts 5 as shown 12 23 Attach the 5 16 3 1 2 Bolt 87 two 5 16 Flat Washers 8 the 1 Metal Spacer 22 and a 5 16 Nylon Locknut 3 to the Front Upright as shown Wrap the Short Cable 23 around a 3 1 2 Pulley 15 Attach the Pulley to the Front U
20. uding holidays To help us assist you please be pre pared to give the following information 1 The MODEL NUMBER of the product WESY85070 2 The NAME of the product WEIDER 8507 Training System 3 The SERIAL NUMBER of the product see the front cover of this manual 4 The KEY NUMBER and DESCRIPTION of the part s see the PART LIST on page 20 of this manual WEIDER is a registered trademark of ICON Health amp Fitness Inc LIMITED WARRANTY ICON Health amp Fitness Inc ICON warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of ninety 90 days from the date of pur chase This warranty extends only to the original purchaser ICON s obligation under this warranty is lim ited to replacing or repairing at ICON s option the product through one of its authorized service centers All repairs for which warranty claims are made must be pre authorized by ICON This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an ICON authorized service center products used for commercial or rental purposes or products used as store display models No other warranty beyond that specifically set forth above is authorized by ICON ICON is not responsible or liable for indirect special or consequential damages arising out of or in con nection
Download Pdf Manuals
Related Search