USER MANUAL DG 2220
Contents
1. Press to enter confirm setting Press to bring cursor from the START MIN to STOP HOUR menu Press to open STOP HOUR setting z will appear Press or to correct HOUR Press to enter confirm setting Press to bring cursor from the START MIN to STOP HOUR menu Press to open STOP HOUR setting z will appear Press or to correct HOUR Press to enter confirm setting Use the same procedure for the rest of the days of the week After this you must program the NIGHT PROGRAM Note If you do not want the processor to turn ON on e g Sundays just enter too in the PROGRAM NO under the SUNDAY menu DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SOR TLF 45 57860100 FAX 45 57860119 November 2 1999 20 NIGHT PROGRAM This program along with the Week Program will enable you to cut down waiting for the warming up time and by decreasing the temperature in the tanks during the night will result in energy savings To set the NIGHT PROGRAM go to the PROGRAM NO menu Press or to the PROGRAM NO menu Press to open PROGRAM NO setting will appear Press to bring cursor to NIGHT PROGRAM Press gt to open NIGHT PROGRAM Following will appear in the Display PROGRAM NO l NIGHT DEV TEMP 20 C FIX TEMP 20 C AOX DELAY 60 MIN AOX DEV 20 mL AOX FIX I 20 mL Press to bring cursor from DEV TEMP menu Press to open DEV TEMP setting will appear Press or to correct NIGHT DEV TEMP Press to enter confirm2. Conveyor or the Imagesetter as a normal D Sub 9 Pol Male or D Sub 15 Female on request see enclose drawing DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 34 SCREEN D SUB 9 POL Male SCREEN D SUB 15 POL Female F1 LO FILTER Q Q F2 LC FILTER FILM SENSOR OUT Q Q F3 LC FILTER OPTO ERRO 4N37 ETE CF ER FILT 4 KI F5 LC FILTER OOOOO ONAN F OPTO WAIT 4N37 F6 ly Z LC FILTER 2 4 PART OF POWER BOARD 4 TO EARTH DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SOR TLF 45 57860100 FAX 45 57860119
3. setting Use same procedure to set the other parameters Note If you use the automatic ON OFF function Do not turn OFF the MAIN POWER switch DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 21 TIME ADJUSTMENT The built in clock shows time day date month and year To adjust use the following procedure Press A or V to the TIME menu Press TIME will appear Press ADJUST will appear Press gt to open ADJUST menu Following will appear in the Display ADJUST TIME YEAR XX MONTH XX DAY XX DATE XX HOUR XX MINUTES XX Press to open ADJUST YEAR setting will appear Press or to correct YEAR Press to enter confirm setting Press to bring cursor from YEAR to MONTH menu Press to open ADJUST MONTH setting will appear Press or to correct MONTH Press to enter confirm setting Use the same procedure to program the remaining parameters NOTE The clock Is a 24 hour clock according to international standard 00 00 11 69 a m 12 00 23 69 p m DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 DAYLIGHT DEVELOPING not installed DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 22 November 2 1999 23 WASH SECTION The wash section is intended to remove any excessive chemistry from the film paper before it enters the dryer
4. No water will come into the tank before the processor is turned ON because there is a built in electric valve which only opens in case of LOW LEVEL or when in PROCESS mode This reduces water consumption Replenishment Mix some additional Developer and Fixer in separate containers Place these under the processor and insert the 1 2 red hose into the Developer and the 1 2 blue hose into the Fixer container Now you can turn the processor ON and set up the programs according to your needs Press the MAN REP DEV and MAN REP FIX buttons for a few seconds to make sure chemistry is pumped up through the system DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 14 CREATING PROGRAMS Choosing a program gt To enter open a program lt To exit a program re To bring cursor up or to increase value in any program when it has been opened Vv To bring cursor down or to decrease value in any program ei when it has been opened SET To enter confirm setting SYMBOLS IN THE DISPLAY Means you can move the cursor up or down from one program to the other Means you can enter a program and change values When the processor has been turned ON on the Control Panel you will find following in the Display MAIN MENU D 30 dev temp F 30 fix temp S 30 speed READY or DEV TEMP if dev temp LOW
5. ON button With Main supply ON 2 ON Processor can be in READY MODE NIGHT MODE or WARMING UP 3 OFF Processor is not powered when the Emergency Stop is activated or the Main supply is OFF The internal clock runs on a battery Darkroom As soon as film paper is detected by one or more of the sensors the processor will start running and the dryer section will be activated Replenishment will take place in relation to the chosen amount per sq mtr ft depending on number of activated sensors After the material leaves the sensors the processor has to run X minutes and seconds After completion of this running time the processor will resume READY MODE and maintain bath temperatures A new film can be entered approx 5 sec after the trailing edge has left the sensor Daylight only installed on request Entering a film through the Daylight slot starts the same sequence as the Darkroom mode but the amount of replenishment is equal to one sensor activated Rewash only installed on request Entering a film paper through the Rewash slot starts the same sequence as the Darkroom mode but without replenishment No input The NO INPUT on the Control Panel will be lit 5 sec after the film paper has left the Darkroom entry This also applies when using the Daylight or Rewash slots Ready mode In the READY mode the processor mainta
6. is Page 8 CONTROL PANE E oes ie en ee ee ees aska ee ER ee ee Page 10 PREPARATIONS ae De oe Ge oe Qa AS A aus Page 13 CREATING PROGRAMS Page 14 CHOOSING a programi se eiae ana GE DR GR ee RE EE ee Page 14 Developer temperature setting ee ee ee EE ee ee Page 15 Fixer temperature setting Page 15 Developing time setting ees ESE Se Page 15 Dryer temperature setting a a ee ee ee ee ee Page 15 Developer replenishment ee EE ee ee ee ee ee ee ee ee Page 16 Fixer replenishment ss ee ee ee ee ee ee Page 16 Anti oxidation delay ee GE ee dad Gee Page 16 Anti oxidation Dev Repl ae ee ER ER OE Ek Page 16 Anti oxidation Fix Repl Ge OE EE EG Ee Page 17 WEEK PROGRAMS as des a Ge lQ ie Ge ed si DA Page 18 NIGHT PROGRAMS erra reta GE DO DE Ous De ce od Page 20 TIME ADJUSTMENT Page 21 WASHSEGTION uuu es Sie Ke AAE E EE AEN GE KG ie Ge Page 23 STATUS PROGRAM cern acrid oge ee Eed anaes Page 24 TOOLS MENU SEE SS ONSE GED Gee Ge Ge DNE GE GER GE yeh ROG SE DE ee Page 25 DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 5 MAINTENANCE aig a tela Ge Ge oe Ge Page 26 Rou
7. 0 600 550 500 450 400 350 300 250 200 150 100 50 0 5 0 0 05 04 0 2 03 04 0 5 0 6 in FOR EX 0 4 cc in 620 ml m DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 18 WEEK PROGRAMS You have the possibility to program the processor to turn ON and OFF at a set time any day of the week Note If you use these programs you must program the NIGHT PROGRAM in order to make these function Press to make sure that you are out of the programs Press A or to the WEEK PROGRAM menu Press will appear Press or to the correct day e g MONDAY Press to open MONDAY setting MONDAY PROGRAM NO i 0 START HOUR 08 MIN I 00 STOP HOUR 17 MIN 00 Press to open PROGRAM NO setting will appear Press or to choose PROGRAM NO e g 1 Press to enter confirm setting will appear Press to bring cursor from PROGRAM NO to START HOUR menu Press to open START HOUR setting z will appear Press or to correct hour Press to enter confirm setting DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 19 Press to bring cursor from START HOUR to START MIN menu Press to open START MIN setting z will appear Press or to correct MINUTES
8. Inspect the dryer section and make sure that the assembly is correctly fitted and in good order Clean all rollers in the dryer section C Drain the fixer bath and refill with a new chemistry solution D Drain the water bath and remove the roller rack Wash the bath and clean the rack before reinstalling and refilling with clean water Film is sticky A Drain the fixer bath and refill with a new chemistry solution B Drain the water bath and remove the roller rack Wash the bath and clean the rack before reinstalling and refilling with clean water Clean all rollers in the dryer section Film is not drying properly A Check temperature setting B Check dryer blower setting C Qualified investigation is necessary Film is jamming in one of the baths A Remove the roller rack and clean it thoroughly Ensure that the rack and its rollers are in their correct locations and that the rollers are turning evenly and freely Film is jamming due to the crossover guide A Ensure that the roller racks are in their correct location and that the crossover guides are correctly fitted DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 32 Phototypesetting paper is jamming A Be sure that the leading corners are folded back correctly emulsion to emulsion at a 45 angle or attach a piece of film as a leader B Make the same investigations that are made for film Processor stops be
9. November 2 1999 1 USER MANUAL DG 2220 DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 THIS PAGE IS NOT IN USE DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 3 NOTICE All statements technical information and recommendations contained herein are based on tests we believe to be reliable but accuracy of completeness thereof is not guarantied and the following is made in lieu of all warranties expressed or implied Before using user shall determine the suitability of the product for his intended use and user assumes all risks and liability whatsoever in connection therewith The processor is to the best of our knowledge suitable to work with all types of chemistries known to the graphic market No statement or recommendation not contained herein shall have any force or effect in any agreement signed by officers of sellers and manufacturer Sincerely Yours DANAGRAF A S DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 4 TABLE OF CONTENTS NOTICE xu Sucuasuqasiuqusquawiiasauquaqaiosaakunwqpamaypaus saunas EEE dud senna Page 3 TABLE OFGONTENT uya uha ua GE ce irs acl eth heels ad Page 4 INTRODUCTION ER EE Page 6 TECHNICAL DATA ees ee Si ee Qy en satan octane Page 7 GENERAL DESGRIPTION ses veg sua ES BES EN Ge SA SR Dee saab se Be Ge wed Gee
10. The water should normally be connected to an In house water pipe with natural pressure There is a built in restrictor in the electrical water solenoid to ensure the correct amount of water circulation The water tank can also be connected to an external water cleaning unit which cleans and circulates the water This will save a lot of water and ensure that the water going to the drain is perfectly clean to comply to local laws and regulations Rewash not installed DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 24 STATUS PROGRAM In this program you can check the total running time of the processor the amount of developed film and the amount of used developer and fixer for replenishment Press or to the STATUS menu Press to open the STATUS menu Following will appear in the Display STATUS POWER ON 1 XXX HR FILM XXX M DEV REPL XXX L FIX REPL XXX L Parameters 2 3 and 4 can be reset to zero when you change chemistry Press to bring cursor to RESET Press gt to open ARE YOU SURE gt will appear Press to reset values DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SOR TLF 45 57860100 FAX 45 57860119 November 2 1999 25 TOOLS MENU This sub menu utilizes a few tools which might be needful The menu consist of the following Fil Dev Low Filling Full Fill Fix Low Filling Full Motor Off On The statusline the empty line
11. above Fill Dev will be filled with when the motor is running This makes it possible for service engineers to see whether the tacho sensor is working or not When the motor is off the line is left blank The Fill Dev and Fill Fix options makes it possible for the user of the Processor to fill up the bath by using the replenish pumps The message after the Fill Dev or Fill Fix tells you what state the Processor is in Low Filling or Full If you have a low level in either of the Dev or Fix baths use the following procedure to fill up the bath automatically Press or to the TOOLS menu Press TOOLS will appear Now the following menu will appear Fill Dev Low Full Fill Fix s Low Full Motor Off If either of the Dev or Fix is Low the following procedure will apply Press or to the menu showing Low Press to open menu Now the Processor will start filling up the chosen bath When the level has been corrected the replenishpumps will stop Press to stop the filling and to exit to the Main menu If you have a Film Jam you can use the Motor menu to drive out the material However this feature should only be used when the no material is stuck around any of the rollers To use this feature use the same procedure as above described DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 26 MAINTENANCE Routine cleaning The most effective way to avoid operating difficult
12. ber 2 1999 TEGHNIGAL DATA FOR PROCESSOR DG 2220 Height including stand Width Length incl Daylight Cassette Weight Power Supply Power consumption total Max film width Min film width Min film length Developing time Internal clock 9 User 1 Night Program Automatic water solenoid for water saving Automatic water re circulating unit optional Automatic air cleaning unit optional Automatic On Off function Automatic replenishment Anti oxidation programs Tank capacity dev fix water Circulation dev fix water Adjustable temp dev fix Adjustable temp dryer Daylight developing and Rewash Slot only installed on request Counter for hours of operation Counter for amount of film processed Counter for amount of replenishment Filter replacement warning dev water air Motor overload warning Water connection Working range 10 45 C 50 113 F 1090 mm 46 4 945 mm 37 2 1900 mm I 74 8 235 Kg 518 Ibs 220V 50 60Hz 3550 W 560 mm 22 30 mm 1 2 120 mm 4 7 20 99 sec 0 1995 mL 22 5 L 6 0 US Gal 22 L 6 0 US Gal 15 45 C 59 113 30 60 C 86 140 F r3 3 4 30 90 humidity DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SOR TLF 45 57860100 FAX 45 57860119 November 2 1999 8 GENERAL DESCRIPTION The processor can be in one of the following modes 1 OFF Processor is powered For startup push the
13. duce it if necessary Consider the possibility that the developer has been contaminated with fixer solution If so it is necessary to drain out the bath and wash it thoroughly Take whatever action is necessary to eliminate the reason for the contamination before refilling the bath with the new chemistry solution the machine must stand level and steady at all times Investigate whether the problem occurred because the film was exposed in faulty conditions non lightproof Film has dual tone dichroic stains A The fixer bath should be drained washed out and refilled with a new chemistry solution This problem is usually caused by excessive carry over or spilling into the fixer bath Film has a milky appearance A Check level of fixer bath and manually replenish if necessary Consider increasing the replenishment rate Also ensure that the replenishment container is not empty and that the hose is not bend or blocked Check the chemistry manufacturer s recommended fixer temperature and reduce it if necessary Drain the fixer bath and then refill it with a new chemistry solution Follow the manufacturer s mixing instructions carefully DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 31 Film has stripes lengthwise A Remove and clean the crossover guides Film is scratched A Check that the crossover guides are fitted correctly and check for possible damage B
14. efreshing the fixer LIGHT ON OFF Here you can turn OFF the light in the DISPLAY if developing red light sensitive materials gt To enter open a program lt To exit a program A To bring cursor up or to increase value in any program when it has been opened V To bring cursor down or to decrease value in any program when it has been opened SET To enter confirm setting DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 13 PREPARATIONS After the processor has been installed by a qualified technician you can prepare to fill up the tanks with chemistry and water NOTE Fixer Always follow the instructions given by the film and chemistry manufacturer It is strongly recommended to put the fixer into the tank before the developer in order to prevent splashing into the developer tank This will cause contamination of the developer and result in a poor developing process The fixer tank is the center tank marked with blue Developer Water Before filling the developer into the dev tank check and make sure that no splashing has occurred when filling the fixer tank If so clean thoroughly The dev tank is marked with red NOTE Make sure that the valve on top of the Developer filter if installed is in the OPEN position before you fill the tanks and turn on the machine If the processor is connected to a water pipe turn it on
15. eing used suits the film being used film is variable from package to package so check the emulsion references Check that the camera lamps are all O K Increase exposure time if necessary Check the film manufacturers recommended development time and increase the time if necessary Check the chemical manufacturer s recommended development temperature and increase it if necessary Investigate whether the developer has become oxidised possibly through lack of use If it has a strong brown colour it should be replaced Check the manufacturer s mixing instructions for the developer and replace the mixed solution if it is too weak DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 30 G Consider the possibility that the developer has been contaminated with fixer solution If so it is necessary to drain out the bath and wash it thoroughly Take whatever action is necessary to eliminate the reason for the contamination before refilling the bath With the new chemistry solution the machine must stand level and steady at all times Flush out the developer replenishment system using the manual replenishment button 7 to pump warm water from a container Follow the instructions in the CHEMISTRY PREPARATION section of this manual when you are refilling the bath Film has a foggy appearance A B C Check the chemistry manufacturers recommended development temperature and re
16. fore film paper exits A Qualified investigation is necessary DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 33 ELECTRONIC INTERFACE TO TRANSPORTER Buffer or Conveyor The communication from the Imagesetter trough Transporter Buffer or Conveyor Is normally two signals Wait and Error The Danagraf electronic is prepared for this communication and can be switch ON and OFF in the Service Program Wait signal indicate a smaller fault not so critical in the processor it can be low level to low high temperature maximum of film In process 3 or the Processor In OFF mode If wait signal arise the Buffer Imagesetter shall wait until the Processor return to normal condition Maximum film in process 3 in the Danagraf electronic is for controlling how many film will be lost if a Jam arise Error signal is indicate a critical fault in the Processor it means a film Jam If a film Jam arise it is necessary to remove all film in the Processor before a new film can be developed The film Jam will arise if a detected film from the inlet sensors not in time has been detected of the exit switch or gets stuck in the exit The Danagraf electronic in On Line mode can be switch ON or OFF normal or invert for the Imagesetter signal the normal communication from the Imagesetter is a wait and wait return and Error and Error return Danagraf can supply the cable to the Buffer
17. ies is to regularly clean the processor its hoses and the replenishment pumps Chemistry is subject to oxidisation and even though the machine has its own program to eliminate this problem the operator should pay special attention to preserving the chemistry and removing crystallized deposits from the equipment The use of floating lids on the replenishment containers to keep out the air can help a great deal to preserve the chemistry which will also give better results and create fewer problems The following suggestions are simple but extremely necessary They will help enormously to avoid spoiled work wasted time lost tempers and unnecessary expense NOTE When you remove the top cover the processor can not run for your safety Be careful always to mount the various parts in the correct position after cleaning Every day Clean the film feed table and the lightproof compartment Use separate damp cloths to clean guides and each set of upper rollers Feed one or two old films before commencing the days work Every week in addition to above Turn OFF the processor and remove all three roller racks Clean them carefully with lukewarm water using separate cloths for each rack NOTE Racks can be removed and refitted without draining out the chemicals but once again it is essential to make sure that not one drop of fixer goes Into the developer bath If this happens the developer must be drained and the bath must then be
18. ins operational tempera ture and the exhaust fan will run as soon as the processor is powered up Whenever the chemistry is warming up the circulation pumps will be running Replenishment takes place according to settings DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 Night Prog Week Prog Time Status Levels Online mode The processor will maintain the chosen temperatures in developer and fixer bath The ANTI OX program will maintain the chemistry balance and turn the rollers to avoid crystallization according to setting NOTE Film or paper input is not possible in this program Start and shut down times for each day of the week are programmable together with the Night Program settings The built in clock shows time day date month and year Setting and adjustment is possible Runs on a battery during power failure This menu shows Total operation time Square meter of processed material 2 Amount of Developer replenish used 3 Amount of Fixer replenish used 4 Position 2 3 and 4 can be reset The developer fixer and water tanks have individual level control If the NO INPUT indicators begin to flash the dev and the fix tanks will automatically be refilled The pumps will work for max 40 sec to minimize damage in case of a leakage You can also press the MAN REP L button and the pump s will pump as long as it is act
19. ivated in order to restore correct level In case of low level the heater and the circulation pump will automatically stop to prevent overheating See ONLINE appendix DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 CONTROL PANEL 10 The Processor is equipped with a Tip Touch control panel which ease the users control of the Process The panel is designed to offer the user the best possible control giving a very comprehensive data read out without being to complex MOTOR OVERLOAD FILTER CHANGE ON MAN MAN CIGH OFF REP REP ON DEV J FIX JL OFF lt gt DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 11 NO INPUT The NO INPUT indicator Is lit wnenever the status of the processor is not normal The status Is not normal when Temperature it too low in Dev Fix Temperature is too high in Dev Fix LOW LEVEL in any tank Processor Is In PROCESS MODE either through Darkroom Daylight or Rewash feeding NOTE For Through the Wall installation the processor is equipped with a red indicator light on the exit side Indicating a NO INPUT status ANTI OX This is lit whenever the ANTI OX program is active This can be programmed individually to give an amount of replenish of Developer and Fixer from 0 99
20. ml at any set time interval from 5 60 min The rollers also turn to prevent crystallization and will run for minimum 5 sec If the processor is in READY MODE but has not been used for a longer time the ANTI OX program will automatically work depending on the setting MOTOR OVERLOAD This is lit if an abnormal high load Is on the motor E g in case of a film jam Then you must turn OFF the processor on the panel remove the cause and turn it ON again FILTER CHANGE When this is lit one of the following filters needs to be changed Water filter optional external unit Air Cleaner filter optional external unit For details go to the chapter Maintenance DISPLAY This is a LCD display with a possibility of 4 lines of information at a time of all the MENU s and PROGRAM s ON OFF With this you can turn the processor ON or OFF manually if you do not use the programmable TIMER for automatic ON OFF function DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 12 MAN REP DEVO This enables you manually to pump up more developer in case of LOW LEVEL after chemistry change or if the automatic setting has been to low for refreshing the developer MAN REP FIX This enables you manually to pump up more fixer in case of LOW LEVEL after chemistry change or if the automatic setting has been to low for r
21. or HIGH PROGRAM 1 Press z will appear Press or to choose Program number e g to open Program No 1 Press to open Program No 1 Following Menu will appear PROGRAM NO 1 1 94 NIGHT DEV TEMP 30 C 15 45 C 59 113 F FIX TEMP 30 C 15 45 C 59 113 F DEV TIME 30 SEC 20 99 sec DRY TEMP 53 C 30 60 C 86 140 F DEV REPL 400 ml m 0 1995 ml m FIX REPL 300 ml m 0 1995 ml m AOX DELAY 60 min 5 60 min AOX DEV 50 ml 0 99 ml AOX FIX 30 ml 0 99 ml NOTE There are 10 different factors in each program that can be set individual to have and maintain a perfect balance in the chemistry DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 15 Developer temperature setting Press to open DEV TEMP setting will appear Press or to correct temperature Press to enter confirm setting Fixer temperature setting Press to bring cursor from the DEV TEMP to FIX TEMP menu Press to open FIX TEMP setting will appear Press or to correct temperature Press to enter confirm setting Developing time setting Press to bring cursor from DRY TEMP menu to DEV TIME menu Press to open DEV TIME setting will appear Press or to correct time Press to enter confirm setting Dryer temperature setting Press to bring cursor from the DEV TIME menu to DRY TEMP menu Press to open DRY TEMP se
22. pected that REAL technical problems will be rare and if encountered will involve the chemistry and materials or the routine cleaning The following pages will provide answers to the most common problems that can be encountered when processing work DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 29 Film quality hints and trouble shooting Image is too dark A If the material is film that has been exposed on a camera make a new test exposure to check that the time being used suits the film being used film is variable from package to package so check the emulsion references Change exposure time if necessary Check the film manufacturer s recommended development time and reduce the time if necessary Check the chemistry manufacturer s recommended development temperature and reduce it if necessary Check the manufacturer s mixing instructions for the developer and replace the mixed solution if it is too strong Reduce developer replenishment setting for a while If good results are restored maintain a lower replenishment rate Image is too light A Check level of developer bath and manually replenish if necessary Consider increasing the replenishment rate Also ensure that the replenishment container is not empty and that the hose is not bend or blocked If the material is film that has been exposed on a camera make a new test exposure to check that the time b
23. thoroughly cleaned and refilled DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 27 Occasionally in addition to above Drain all three baths and empty the replenishment containers Fill the baths and replenishment containers with water and ensure that the racks baths hoses and containers are thoroughly washed by flushing and pumping water through each bath system After refilling the baths repeatedly press the manual replenishment buttons for the developer and fixer to eliminate any air pockets in the system DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 28 TROUBLE SHOOTING General guality control statement If there is a reduction in the quality of the processed materials it can probably be solved by checking the control settings the operational procedures or by giving a little extra attention to the routine cleaning A small amount of time invested in SELF HELP will usually avoid a lot of wasted time and possible expense which will result from calling in a service technician If however the problem seems to be electrical or mechanical do not attempt such complex trouble shooting unless you are well qualified to do so Great care has been taken in the development specification and manufacture of this equipment to ensure that it will give many years of reliable performance and quality It should therefore be ex
24. tine Cleans uqu OE EE N IE HG N Page 26 Evry dad ee ds ie ee Ras ie ee oe eg ee ie ee DE ED ee Aa Page 26 Every Week GE uu Ee ED ton De ocak te Page 26 Occasionally EE ED DE ED DE DE DE Ee Ge oor Ee ER Ee mentors Page 27 TROUBLESHOOTING Sau anu Ge Ee De ee ei Page 28 General quality control statement Page 28 Film quality hints and trouble shooting Page 29 ONLINE appendiks a a au Qala a asa AS De Page 33 DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 6 INTRODUCTION This Graphic Film Processors is equipped with the revolutionary Tip Touch control panel This feature presented as a built in control pad enables even the unskilled operator to perform all processor settings in a logic way with visual control of all data input At any time the operator can check the status of the chemistry temperatures processing speed etc The ergonomic design working height accessibility and multitude of features will economise your operating as well as your maintenance time and guarantee a high standard of reliability The user of this Graphic Processors will be able with help of this selfexplaining manual to operate the unit to its full extend and produce quality output from the beginning GOOD LUCK DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 Novem
25. tting will appear Press or to correct temperature Press to enter confirm setting DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 16 Developer replenishment Press to bring cursor from DEV TIME menu to DEV REPL menu Press to open DEV REPL setting will appear Press or to correct amount Press to enter confirm setting Fixer replenishment Press to bring cursor from the DEV REPL to FIX REPL menu Press to open FIX REPL setting will appear Press or to correct amount Press to enter confirm setting Anti oxidation delay Press to bring cursor from FIX REPL menu to AOX DELAY menu Press to open AOX DELAY setting will appear Press or to correct time Press to enter confirm setting Anti oxidation Day repl Press to bring cursor from the AOX DELAY to AOX DEV menu Press to open AOX DEV setting z will appear Press or to correct amount Press to enter confirm setting DANAGRAF A S INDUSTRIVEJ 11 13 DK 4180 SORG TLF 45 57860100 FAX 45 57860119 November 2 1999 Anti oxidation Fix repl Press to bring cursor from the AOX DEV to AOX FIX menu Press to open AOX FIX setting will appear Press or to correct amount Press to enter confirm setting For converting between cc sq in ml m ml m 1000 950 900 850 800 750 700 65
Download Pdf Manuals
Related Search