Home

MANUAL EQUIPOS ACUSTOMAGNÉTICOS 58 KHz

image

Contents

1. s not detecting the system when exit from it EDITION MODE 1 SWITCHES System works with the configuration selected on the TX board selectors 2 PROGRAM works with setting configuration from the program TRANSMISSION It must works at 100 of power Transmitter power might be modified from the software moving potential cursor TX patented to reduce the tag label detection area 1f 1t would be necessary Transmission may be locked in BLOCK cell In this way system continues operating in RECEPTION mode This 1s helpful when system is beeping and we do not know exactly if is caused by tag label or other interferences once locked transmission system to stop beeping we may determinate clearly that there are some tag label around JE SISTEMAS ANTIHURTO S L 14 ALARM INHIBIT 1 2 ALL System works normally but without acoustic light warning Is useful to figure out where noise comes from avoiding continuous system beep Tick INHIBITED SABOTAGE System alerts when a LRAD Noise generator system is locking 1t and therefore tag labels detection Tick INHIBITED DELAYS Window Fixed value Synchro go to pag n 17 CHANNEL 1 CHANNEL 2 1 2 3 4 5 GAIN Values from 1 250 System sensitivity Increase Gain it means more detection more noise Useful value for detection setting Always be set at minimum with optimums tag labels detection SIGNAL THRESHOLD Value from 0 1
2. S L 19 11 SECURITY RECOMMENDATIONS Following information represent different security measures technician and installer must know while wiring or keeping acustomagnetic systems Systems must be far from wet areas Avoid installing the system near neon tubes or lamps before testing it We must switch off power supply when board cables were handled Exist danger of electric contact with wet hands If we manipulate connectors only in case we manipulate connector that comes from power supply we must unplug it So we avoid the sudden lost of electric current of TX antenna that may damage it Keep labelled products away from the antennas at least 1 5 m minimum Wiring between antennas must be done in the ground floor straight line never must be done over the antennas or in doorframes 12 BEFORE INSTALLATION Congratulations on purchasing one of the best AM systems in the market Once received the system inspect all packages carefully for possible damage If you find any contact the carrier Place the packages in a clean and level surface with enough room to move Inspect the equipment and make sure everything is properly assembled and in perfect condition and no damage as a glimpse broken housings cables pinched bent pins etc If any item is damaged DO NOT connects your computer or makes any connections unless instructed by Technical Support EL A S SISTEMAS ANTIHURTO S L 20
3. port COM haven t been installed yet see image 4 as you can see in image 4 number 2 in Other devices gt USB serial port it s not installed If click Serial Port in USB Port with right button of the mouse you may install drivers from the CD following same steps than before When installation is already finish you will see the USB Serial EAS in Control Panel gt Device Manager gt Port COM amp LPT as seen in the image below Archivo Acci n Ver Ayuda e0 n S BA a 34 danil amp Adaptadores de pantalla x Adaptadores de red 3 Bater as Controlador de tecnolog a de memoria cg Controladoras ATA ATAPI IDE o Controladoras de bus serie universal y Controladoras de sonido y video y dispositivos de juego 2 Dispositivos de imagen ds Dispositivos de interfaz de usuario HID 4 Dispositivos del sistema 4 Equipo Bi Monitores M Mouse y otros dispositivos se aladores E Procesadores 79 Puertos COM y LPT a USB lt gt Serial EAS COM5 PA ASK 3 Teclados ca Unidades de disco Unidades de DVD o CD ROM Imagen 5 Then the USB will be installed and ready to use JE SISTEMAS ANTIHURTO S L 12 2 Connection Pc Transmiter To make this we use an input MINI USB connecting the input connector J9 Board TX USB al PC Following step is shown in parameters patch of system with program point 6 SET PROGRAM PARAMETERS TX RX and MONO BUTTON DESCRIPTION There are several buttons on
4. program screen Up in left we have 3 buttons First button on the left Read parameters shows us actual configuration of system We must press 1t at the beginning of each setting to see the configuration stored in the Tx board Button x apply changes store in board memory all data we have insert in cells If we don t push this button transmitter board won t store in changed made Third button WD analyzer shows us analysis in real time of position system with modified parameters JE SISTEMAS ANTIHURTO S L 13 M Barrera Acustomagnetica g Ni hs lt AS LE O COMA y E Node O edition radar TRA Options MODE CHANNEL 1 CHANNEL 2 C switches program Gain 20 Gain 20 TRANSMISSION UC TS Signal threshold 20 Signal threshold 20 5 Sabotage threshold 80 Sabotage threshold 80 TA Power n pone Real noise 69 Real noise 0 eee s Se D ae Reading Level 29 gq _ Reading Level O Alarm inhibit all sabotage DELAYS window 70 synchro 2 General Information Firmware version EAS 10CPNL Software version 7 0 0 276 N de serie 0000000297 The three next buttons Bl ul you can use them to choose the program language The top right button that shows a door is the exit of program It s important the connector cable between PC and TX board be connected before exit the program if not will be an error in program because it
5. we use them to change manually parameters such as power gain and other variables SW1 potency consist of eight selectors 1 in ON syst Transmitted at 50 3 slave 2 in ON syst Transmitted at 75 5x l and 2 in ON syst Transmitted at 100 6 inhibir bluetoolth 4 in ON reverses the phase of the syst 7 inhibit sabotage alarm 8 x SW2 gain consist of eight selectors where the first six are corresponding to the gain adjustment in geometric progression 1 in ON creates a value 8 7 without alarm 1 and 2 in ON creates a value 16 8 without emmision 1 2 and 3 in ON creates a value 32 1 2 3 and 4 in ON creates a value 64 1 2 3 4 and 5 in ON creates a value 128 1 2 3 4 5 and 6 in ON creates a value 256 M Barrera Acustomagnetica Node 1 edition radar optione SWITCHES SWi1 power 4 invert phase 6 inhibit bluetooth 7 inh alm intert 7 no slarm o 8 no emission Compatibility durati E ro V compatible DURATION OF SABOTAGE Time that must be blocked by the real noise system to give us the alarm COMPATIBILITY Modifies the best position of detection tag labels vertical horizontal JE SISTEMAS ANTIHURTO S L 18 VERY IMPORTANT Reset transmitter board The way to reset emitter board is simple Switch Off power supply and placed all the CPU switches SWI and SW2 in OFF and
6. 00 Horizontal yellow line in the Oscilloscope System advises when tag label is detected 58 KHz tag label signal has to overtaken the threshold green line on the oscilloscope to achieve system trigger As higher threshold signal more 58 KHz signal will needs system to trigger If there is environmental noise real noise nivel de lectura and it causes false alarms we can avoid it increasing the threshold SABOTAGE THRESHOLD Value from 0 100 Red horizontal line in the Oscilloscope Minimum determinate interference level to triggers the acoustic light signal Standard value is 80 REAL NOISE It can be seen on the oscilloscope represented by irregular red lines System informs about real environmental noise close frequencies of 58 kHz READING LEVEL It can be seen through the oscilloscope represented by green lines level of 58 kHz tag labels that system detects If we have on the oscilloscope 58 kHz lecture signal and once locked the transmission this has disappeared that mean there are tag labels around Otherwise it will mean that there is any LRAD Noise generator device around at 58 KHz Avoiding false alarms is recommendable reduced the Gain or increase the Signal Threshold JE A S SISTEMAS ANTIHURTO S L 15 Ml Barrera Acustomagnetica e Ni ho Gal ca Mom EZ ES Node 1 ul edition radar TRA Options MODE CHANNEL 1 CHANNEL 2 C switches le program ra 1100 ayer 20 pa Le ee Signal thresho
7. ES SSS SISTEMAS ANTIHURTO S L SSHKhbz ACOUS TO MAGNETIC SYSTEMS WIRING HANDBOOK E Z SISTEMAS ANTIHURTO S L 4 de Revisi n 1 06 2012 INTRODUCTION SYSTEM DESCRIPTION a TRANSMITER ANTENNA TX b RECEIVER ANTENNA RX c POWER SUPPLY DIFFERENT CONFIGURATIONS ANTENNAS WIRING PC CONEXION 1 Drivers installation 2 Connexion Pc Tx 6 PARAMETERS SETTINGPROGRAMM 1 Button description 7 8 9 10 SYNCHRONIZATION OPTIONS COMMON PROBLEMS SAFETY RECOMMENDATIONS JE 4L 3 SISTEMAS ANTIHURTO S L 2 1 INTRODUCTION E A S SISTEMAS ANTIHURTO S L design manufacture acousto magnetic technology systems These acousto magnetic systems when they are installed and in function their working frequence is 58 Khz Acousto magnetic technology is typified to make high efficiency in system high detection and small number of false alarms The installation software is very easy to use You can vary several parameters in order to match magnetic field generated by antennas 58 KHz There are different kind and size of acousto magnetic alarm tag labels with a maximum detection field maximum distance that alarm tag label is detected by acustomagnetic system JE SISTEMAS ANTIHURTO S L 3 According to space features that antennas have to cover we have to choose suitable alarm tag label so the patch has to be done between system and selected alar
8. e must change bulbs of place put them as far as possible of system or replace them with another working in different frequency range With the two antennas put in their places TX antenna will be put nearer of power supply and always one front the other we make cable assembly Configuration is Power Supply Blue Grevy Black Red Yellow 2 White 1 Photo 8 Photo 9 Cable between 2 antennas photo 10 has to be connected in the RX board through RJ45 connector and in the TX board photo 11 Colours code have to be the same in both connexions pin to pin Photo 10 Photo 11 JE SISTEMAS ANTIHURTO S L 8 When we have assembled cables between antennas and cable of power supply to transmitter board we can switch on power supply to make this possible we press the switch on off of one side of power supply TX board shows us 1f system 1s working properly To obtain this well operation leds line must be completely switched on are located in the upper half part of the board In the case this not happen we must go changing jumpers position to get both led lines switch on Jumpers Photo 13 When system 1s switched on right we connect TX board with computer to match with the program JE SISTEMAS ANTIHURTO S L 9 5 PC CONEXION 1 Drivers installation Plugging in and turning on a device To install any USB device just plug 1t in to your computer Then turn 1t on before connecting it Next d
9. ecide which USB port to connect your device to You can use any port the next time you plug in the device Imagen 1 Plug the device into the USB port Windows can t detect new hardware You have to install it manually from control panel Device manager gt _Other devices gt USB serial EAS E plants A ix ASPEN BUC r de d PORT ese Ben By Adeptadores de par sita Adiptadores de red Y Beteries E Controlador de tecnolog a de memora ca Controladoras ATA ATAPI DE Y Controladores de bus sene universal Controladoras de sonido y video y dispositivos de juego 2 Dispositivos de imagen Oy Dispositivos de interfaz de usuario HID e Dispositivos del sistema EB Dispositivos portat es MM Equipo E Monitores PL Mouse y otros dapoutwes se aladores a y Otros dispositivos dy USB lt gt Serial EAS D Procesadores Teclados Urndedes de dace eb Vnidedes de DVD o CD ROM E A MAA AFR 4 ARANA PRAGA Imagen 2 Ec Z S SISTEMAS ANTIHURTO S L 10 Then appears the following message How do you wish you to search driver software Then you click on Search device software on the computer 1 ANA i Archivo Acci n Ver suis le S Em As T cs a Ey danil C mo desea buscar el software de controlador a IT i v Y Yv w v Y Buscar autom ticamente software de controlador actualizado Windows buscar en el equipo y en Internet el software de con
10. ing to detection wished Range door is even 1 20 metres by each side with Hammer tag Dual System In this configuration the TX board is assembled in One antenna and RX board in other one Each antenna is put in each side of the door Range door is even 2 50 meters Three antenna system TX board goes in one antenna and the other two RX boards each one in a different antenna Transmitter antenna goes between the two leaves of the door and each receiver antenna in each side of door Range big door For more types ask connections in factory FE A SISTEMAS ANTIHURTO S L 7 4 ANTENNAS WIRING In acustomagnetic system wiring we need a less space to put antennas If it s possible we leave a space of 5 10 cm between the wall or exit door and outside limit of each one of antennas We make the hole in the ground to fix each antenna on its ends If there 1s pre wiring each antenna will be put in each hole to coincide cable pass holes with holes of the bottom of antenna It s important observing around where antennas it s going to be wired because if there is a bulb with neon lights that works in frequency range of 50 60 KHz or other acustomagnetic system wired in proximities In case of being systems in proximities we only have to synchronize them see parameter patch with program and synchronization but in case of being near a bulb of neon light this can make interferences with system working To solve the problem w
11. is as you can see in the picture below with a few signals JE SISTEMAS ANTIHURTO S L 16 El Acousto magnetic barrier a S edition radar Identify barriers Gl Mo 1 Lines you see on the screen are signals from other systems AM We need to place our system with one of these signals to synchronize our system with the rest 4a Slide cursor on the oscilloscope across the screen to locate first vertical white line at the beginning of the signal to keep this one within our block Block from 1ts white line to green line We could see that N of RS change unless good sync being in O 5 When we are synchronized with rest of the system signals click Send and then click on Detect Barrera and return to Edit mode 6 In edit mode we can see Synchronization box show us same value of RS as Radar screen IMPORTANT Click Read Parameters to review that system has stored the synchronization delay value properly Is in this moment when we are really in sync with the other systems around us of 58Khz 9 OPTIONS In the tab Options we find three blocks of cells Cells show us the information of some established parameters such as duration the acoustic warning or light indicator rhythm JE A S SISTEMAS ANTIHURTO S L 17 System works in Selector way let s see its configuration Block selectors show us the status of switches SW1 and SW2 Both are situated in the TX board
12. ld 20 E Signal threshold 20 Sabotage threshold 80 x Sabotage threshold 80 TA Power R ek Real noise 702 S Real noise 0 LE Reading Level ES E A Reading Level 0 Alarm inhibit M iall M sabotage DELAYS window 70 synchro 2 General Information Firmware version EAS 10CPNL Software version 7 0 0 276 N de serie 0000000297 7 SYNCHRONIZATION Box Sincro on the Retardos square When we installed a system where there 1s Other as them emitting at 58 kHz It must be necessary be synchronized with them Otherwise we can come across that system starts to give false alarms or trigger the others This is caused because our transmission signal enters in other systems reception or upside down a SYNCHRONIZATION PROCEDURE What is synchronism AM Systems emitted discontinuously way that means that do not emit all the time but intermittently and at a specific time Provided that AM System is installed has to be synchronized with the rest around Procedure is quite simple with our software 1 Open the program 2 In Radar click in Detector Barrier 3 Oscilloscope screen 1s divided in two by the yellow line which creates two separate screens one for channel 1 and one for channel 2 if you re working with l or 2 RX GAIN mark 10 automatically but it may be changed in order to detect farest signals 4 If there is a system close to our system oscilloscope screen will reflect th
13. m tag label SISTEMAS ANTIHURTO S L 4 2 SYSTEM DESCRIPTION a TRANSMITTER ANTENNA TX Transmitter antenna is made up of 2 loops Each loop is joined to an electronic transmitter board photo 3 in the top connectors X5 amp X6 Photo 3 TX Board Panne ddd gt 7 gt E X5 Photo Monnoantena ANTENNA LOOP MINI USB CONNECTOR PC LITTLE BUZZER LED MASTER SLAVE CONNECTION POWER SUPPLY JE 4L S SISTEMAS ANTIHURTO S L 5 B RECIEVER ANTENNA RX Receiver antenna is made up of two loops as transmitter antenna The two ends of each loop are connected to RX board they come one from up and the other one from down Photo 6 Lower loop Upper loop a Al koa RX Board S1 Buzzer Light out C POWER SUPPLY Power supply transforms net voltage 220 V in optimum voltage to system working This power supply is composed by a coil of 1 Amp a board with 3 fuses electric current way in with switch on off with fuse carrier and connector cables between board and coil In photo 7 is shown power supply installed Connexion of Power Supply is of 6 strands keeping free n 1 JE SISTEMAS ANTIHURTO S L 6 Power Supply Photo 7 Interruptor on off 3 DIFFERENT CONFIGURATIONS There are 3 possible configurations to install acousto magnetic systems Monoantenna Is a system of an unique antenna This antenna can be put in a side of the door or in the middle accord
14. then connect the power supply again At this moment Emitter board make a scanning that can be viewed on LEDs Switch Off power supply again and CPU selectors will return to the initial configuration Switch On power supply connect to the program and start with the setting Once is reset the configuration is SELECTOR mode so when we connect to the PC first thing we have to change is Program mode to make the other changes be stored in the CPU 10 MOST FREQUENT PROBLEMS PROBLEM CAUSE REASON SOLUTION There are low or not detection Insufficient increase value Increase value of that channel areas Faulty alarm label Prove with other tag label of the same sort System detects alarm tag label Wrong buzzer connections Change connection cables of but doesn t beep Inhibition alarm cell of the buzzer in the Rx board program selected Click in alarm inhibition cell Faulty buzzer and button of modif Parameters or take off the selector Change buzzer of the system Analyst detects much electric Unfavourable environment for Look at environment of system noise the system by the presence of Modify Gain values of selected ballasts pc s TV s channel Badly synchronized Bring close distance between antennas if it is possible Well synchronized Tx board turn but without Tx board without set or bad Check RJ45 connection with detection tag labels connection to RX RX E A S SISTEMAS ANTIHURTO
15. trolador m s reciente para el dispositivo a menos que haya deshabilitado esta caracter stica en la configuraci n de instalaci n del dispositivo Buscar software de controlador en el equipo Buscar e instalar el software de controlador de forma manual gt a TN e ar dE gt 2 O Ieee E 4 o y E w vw Y w Imagen 3 Insert CD Then select folder Drivers USB EAS The installation progress will be running a errant a dynia M A A A AA C Andere cum Ve Anes ETS EA ES qe el lt crtotecerm de ten re rr Y rr iras ae oe O Corcertuds ak UD Cerrertete ee oH Ceeceemede oc US Y Cercerteds ue VA y ecb IO fared UIB Ural Her Tort 2924 Y telle ION Ferro LSS Verena Hor Cortar SO HAT Fond USE Lime Hoa Cer 202 DiN 100 Parra LISE ewer Mart Cortcty AO Y Pete DE end USE renal Hen Cortete 18 miN 100 Fond US arias Hon Coetic er 2438 O teh IO Formo LS Erie cad Hert Contratar MISA D SIR NOS rnb LEO Eee ned Han Corri BC TA Sarl LAS SSS Corbadetenn de sreda y vides p beses de page Fe oo de rage QG Topos de rentar te marw HR MD Dip del ctra MD corr ce antiu we Veste be te dhe E Unidades de VO CD ROM Imagen 4 E Z SISTEMAS ANTIHURTO S L 11 When installation in finished would appear this again Hardware can t be found Thus you can see number 1 that USB Serial EAS has been recognized by Windows System But the drivers of

Download Pdf Manuals

image

Related Search

Related Contents

1769-IN026C-EN-P, Compact I/O Thermocouple/mV Input Module  Sony KDL-20S40xx Flat Panel Television User Manual  "取扱説明書"  Manual - Microh DJ  Digitus PCI-Parallel card  Philips 29PT5458 29" real flat TV  MODE D`EMPLOI    DOMINO Version 2.5.0 additional service manual for new - S-MED    

Copyright © All rights reserved.
Failed to retrieve file