Manual - Northwood Technology
Contents
1. 5 Radio work mode with the CD04 6 or 14 km 6 or 14 km module Optional external covering Type CDH Rx tightness class IP56 Type CDH Tx tightness class IP66 Characteristic features of the CDO6 set communication between transmitters and receivers of the RS485 standard with the speed of 2400bps or 9600bps on the basis of the PELCO D protocol a possibility of communicating in the one way mode without confirmation or in two way mode with confirmations the receiver sends feedback to the transmitter concerning the receipt of the order and its correct performance at the same time the transmitter signalizes that the transmission is successful no delays in the transmission all orders are performed immediately a possibility of connecting up to 8 devices of different addresses from 100 to 107 in one bus bar communication can function by means of wire or radio interface with CD04 modules the CD06 Rx receiver can be controlled by means of the CD06 Tx transmitter or by means of the PTZ keyboard the receiver can be set to two work modes bistable and astable the receiver can be divided and half of outlets will work in the bistable mode and the other half in the astable mode it is possible to turn on the EEPROM memory in the receiver in which last states of outlets are registered and in case of breaks in power supply these states will be regenerated one receiver can work in the one way work mode on one address theoretically2. this receiver can control unlimited number of receivers the receiver has a possibility to set addresses for outlets 1 3 and outlets 4 6 separately then the inlets IN 1 IN 3 control the outlets OUT 1 OUT 3 of the first receiver and similarly the inlets IN 4 IN 6 control the outlets OUT 4 OUT6 of the second receiver this option gives a possibility to connect e g four transmitters controlling three outlets in eight receivers in one bus bar Preparing the CDO6 set for work It is recommended to make the first start and configuration of the system in workshop conditions in small distance It can save much valuable time in the configuration of the CD06 set for different applications 1 Connect the modules with one another connecting RS485 wires to appropriate blocks A B of the transmitter and the receiver Connect devices to the inlets IN 1 IN 6 of the transmitter and to the outlets OUT 1 0UT6 of the receiver NO normally open contact NC normally closed contact Z common contact Configure both devices in an appropriate way see section Configuration of the CDO6 set Connect the power supply adaptor to CD06 modules and then to the power supply socket The POWER diode indicator shows the supply state the green light should be on The effect of floating light should appear on the diodes IN 1 IN 6 in the transmitter what shows that the transmitter is synchronized with the receiver At th
3. S network in the two way transmission e the transmitter can control up to 32 receivers only in a one way mode in two way mode the control in a two way mode takes place only in the following way one transmitter gt one receiver or one transmitter gt two receivers of different ID addresses e while controlling receivers by means of the PTZ keyboard it is necessary to remember to turn off the two way mode and to turn on the bistable mode in the receiver e it is not possible to control the CDO6 transmitter and the PTZ keyboard by means of one receiver e the transmitter s inlets have mass on one of outlets so it is not possible to connect a different potential from the same power supply adaptor in this place Each time turn the power supply of the transmitter on the outlet state is changed for an opposite one Most probably a bistable mode and a continuously closed outlet in the transmitter are chosen In the bistable mode the transmitter s inlet should be controlled by the growing impulse that is a change in the state closing opening and not a continuous closing of the inlet Verify the correctness of SETTINGS in the CDO6 Rx PIN5 and PIN6 receiver Apart from the correct connection of RS wires the devices do not communicate with one another Check if the changes in the states of inlets cause light in the TxD transmitter s indicator and the RxD receiver Check the transmission speed settings it should be the s
4. ame in both co operating devices The POWER indicating light does not work Check the correctness of the supply wire connection the level of this voltage and polarity The scope of voltage 10 14V DC The control takes place in a chaotic way and is not in accordance with the transmitter s control Reset the EEPROM memory by means of turning on and off the DIP8 switch in the transmitter or the receiver Check whether the RESPONSE DIP8 switch in both devices is set in the same way In case of using the advanced functions and starting transmission confirmations it is required to have the function switched on in both devices in transmitters and receivers After the control of the transmitter indicators start to blink most probably the function of two way RESPONSE PIN8 ON was turned on in the transmitter and the receiver does not respond or has this function turned off Check the correctness of settings and connections of RS485 wires A longer description of the device with detailed descriptions of all functions and exemplary connections can be found on the following website www camsat com pl Manufacturer CAMSAT Gralak Przemystaw ul Ogrodowa 2a 86 050 Solec Kujawski Offer and information www camsat com pl Service serwis camsat com pl General terms and conditions of a warranty Camsat company gives a warranty of 24 months for transmission sets of the following series TCO 5807 CAM 5816 CDS 5021 CD04 CD06 CDS 5IP 1 In c
5. ase of detecting incorrect work of a device before giving the device to the service it is necessary to make sure that everything was done in accordance with the instruction manual 2 In case of giving or sending the faulty device to be repaired it is indispensable to enclose a detailed description in the written form including faulty action of the device with taking into consideration work environment and the way in which they can be seen 3 One can use the warranty if he shows the proof of purchase a receipt with the claimed device including the purchase date and a description of the damage 4 The warranty repair includes only damages resulting from causes included in the sold device 5 The warranty repair will be made in the shortest time possible not exceeding 14 days counting from the date of accepting the device to be repaired in the service In case of a necessity to import parts the repair date can be exceeded After making the repair the warranty period is exceeded by the time of repair 6 The guarantor is not responsible for losing configuration settings of the device resulting from the repair of the device or its damage 7 The guarantor can refuse making the warranty repair or completely renounce from the warranty in case of stating that seals on the devices or subsystems included in it are broken 8 All remarks concerning the service and resulting from the warranty are made only in the service of the Camsat company CE i
6. e
7. e same time TxD diodes data transmission and RxD diodes data receipt should blink When the floating light effect stops devices are ready to start work Diodes in the transmitter should be set according to the state on the inlets IN1 IN6 If one of the diodes IN 1 IN 6 in the transmitter starts to blink it is necessary to check the correctness of communication It can be caused among others by incompatibility of the transmitter and the receiver the lack of confirmation of data receipt by the receiver in the two way work mode disturbances in the RS485 line etc Co operation of the CDO6Rx receiver with the PTZ keyboard The CDO6 Rx receiver can be controlled by means of any PTZ keyboard with the PELCO D 2400 and 9600 protocol The following PTZ keyboard keys are used in this purpose ZOOM ZOOM FOCUS FOCUS and IRIS IRIS Each of these keys controls an independent transmission outlet in the receiver It is necessary to set the same transmission speed 2400bps or 9600bps and the same ID addresses from ID100 to ID107 in both devices in order to control transmission outlets by means of the PTZ keyboard Setting these addresses takes place in the same way for PTZ video cameras The PELCO D protocol has to be set in the PTZ keyboard Advanced functions of the CD06 set 1 Two way transmission with feedback If the user wants to be informed about the real switching of the receiver outlets it is necessary to start the two
8. nchronizes current states of the transmitter s inlets with the receiver s outlets Retransmission is possible only in the two way mode Turning off the function PIN8 gt ON PIN7 gt ON Permitted connections of several CD06 sets One way transmission a b c d e f g 1 transmitter controlling maximum 32 receivers of the same address maximum 32 transmitters controlling 32 receivers of the same ID address maximum 8 transmitters controlling 8 receivers of different ID addresses 1 transmitter controlling 2 receivers of different ID addresses maximum 4 transmitters controlling 8 receivers of different ID addresses 1 PTZ keyboard controlling up to 32 receivers of maximum 8 different addresses maximum 32 PTZ keyboards controlling 32 receivers of maximum Two way transmission a b c d 1 transmitter controlling 1 receiver of the same ID address maximum 8 transmitters controlling 8 receivers of the same ID address 1 transmitter controlling 2 receivers of different ID addresses maximum 4 transmitters controlling 8 receivers of different ID addresses When several transmitters PTZ keyboards are connected to one network it is necessary to remember that one cannot control several transmitters PTZ keyboards at once in one network it has to be done in turn Configuration of the CD06 set The whole configuration is made by means of switches of the Dip switch type placed at the back of the device T
9. o canGaryr CAMSAT www camsat com CD06 Transmitter and receiver This set is used for remote control turn on off by means of any devices for long distance It uses the RS485 wire interface The CDO6 Rx receiver possesses six transmitters in it of the current load up to 4A each The NO normally open contact points are directed to the term block and the NC normally closed ones are directed to the transmitter It is possible to control outlets in the receiver by means of the CDO6 Tx transmitter or the PTZ keyboard Devices possess the signalling system by means of LED diodes which shows the state of inlets in the transmitter and the state of outlets in the receiver The CD06 set is composed of The CDO6 Tx transmitter The CDO6 Rx receiver Instruction manual Guarantee card Technical data The number of ID addresses 8 Type and number of outlets inlets 6 potential free independently 6 independently controlled inlets controlled outlets of the NO normally open and NC normally closed type The maximum current load of outlets 4a o e O 8 e R R N1 The work mode Bistable and Astable Bistable and Astable The temperature scope of work 0 to 55 C with the external covering Oto 55 C with the external 20 to 55 C covering 20 to 55 C 78x107 28 69x80x28 Co operation with the PTZ keyboard PELCO D with the CD06 Rx receiver with the CD06 Tx transmitter The recommended radio module CD04 CD04 UTP cat
10. ransmitter PIN1 PIN2 PIN3 the address of the following inlets IN 1 IN3 see table No 1 Address settings PIN4 PINS PIN6 the address of the following inlets IN 4 IN6 see table No 1 Address settings PIN7 the transmission speed OFF 2400bps ON 9600bps PIN8 the work mode ON two way with a feedback OFF one way Receiver PIN1 PIN2 PIN3 the address of the receiver see table No 1 setting addresses PIN4 the transmission speed OFF 2400bps ON 9600bps PINS mode for the following outlets OUT1 0OUT3 ON astable OFF bistable PIN6 mode for the following outlets OUT4 OUT6 ON astable OFF bistable PIN7 renewing data after resetting them supply break ON retransmission OFF reading the last states from the EEPROM memory PIN8 work mode ON two way with a feedback OFF one way Address PIN1 PIN2 PIN3 Table No 1 Address settings REMARKS The final reading of settings takes place after resetting the set thus after each change of settings it is necessary to reset both devices It can be realised by changing the PIN8 state or by disconnecting the device from the power supply and connecting it once again Things to keep in mind while designing networks with CD06 devices in order to avoid errors in their functioning FAQ e only one transmitter of a given ID address can be connected to one R
11. way transmission see point Configuration of the CD06 set After turning this function on after receiving the order the receiver sends the confirmation of its performance to the transmitter Then indicators in the transmitter signalize that its orders were performed in a correct way by the receiver and the LED indicators are alight in accordance with the state of outlets in the receiver Turning on the function PIN8 gt ON 2 Reading states from the EEPROM memory before the power cut The receiver and the transmitter are equipped with volatile memory in which the last states of the receiver s outlets and the indicators of the transmitter s inlets are registered After the power cut it is possible to turn on the function in the receiver in order to show all states of outlets from the period before turning it off see point Configuration of the CD06 set The LED indicators and transmitters in the receiver will be set in accordance with the last changes In addition the transmitter immediately sends current states of all inlets to the receiver Turning on the function PIN7 gt OFF PIN8 gt bez znaczenia without meaning 3 Retransmission after the power cut In order to make the transmitter show more detailed values the user can start an additional function of retransmission in the receiver see point Configuration of the CD06 set After turning the power supply on the receiver forces reciprocal communication which sy
Download Pdf Manuals
Related Search