Perfect Sun Wolff System 28-2F user manual
Contents
1. Setting the address manually Before connecting your sunbed to the T Max Manager or T Max 1A or 3A the address of your sunbed must first be set Set the address manually as described below Setting the Address 1 Make sure the sunbed display is showing 0 2 Press the red stop button and without releasing it press the green timer button and hold both for three seconds The display should indicate an address number from 1 to 255 1 99 100 128 blinking dot 252 255 blinking dot 3 If you are using a T Max 1A or 3A as a master remote the ad dress of the sunbed must be set to 1 If you are using a T Max Manager each sunbed must be assigned a different address To adjust the address press the green timer button to count up until the desired number from 1 to 128 is achieved Addresses 252 to 255 are not normally used 4 Press the red stop button to return to the normal display mode Using Your Sunbed Before using your sunbed please note the following e Your skin should be free of cosmetics tanning oils or other body lotions prior to tanning except for those specifically made for use with tanning devices However do not remove natural body oils by bathing or showering immediately before tanning e Keep treated hair from contacting sunbed surfaces Many hair prod ucts can damage the sunbed acrylic Wear a shower cap or towel if you use gels mousses sprays or other hair pro2. PI to pro vide the needed power to the wireless unit Remote System Hook up Scenarios Follow the diagrams below and on the next page to see the many differ ent scenarios for hooking up your salon If you need further assistance call T Max directly at 417 297 0361 Scenario 1 T Max Manager Series with Complete Wireless Connect one G2 with Power Injector to the Manager and one G2 to each of the tanning beds Install as many beds as you like with this configuration Units that do not communicate with T Max will need an G2 with Power Injector and an additional 3A to operate If you have an older T Max Manager that doesn t support auto addressing set the address of each sunbed manually as described in Setting the address manually You can place your sunbed at any location in the series K NT v BNI _ Non T Max incorporated units Scenario 2 T Max 3A with Wireless In single sunbed installations the T Max 1A and 3A can offer the same control as the T Max Manager eliminating the need for a Man ager If you re using a 1A in this manner it must have a chip labelled master installed on its circuit board The remote control bypass plug must not be used in this configuration The 3A may be used as a mas ter with no modification C After you have set the T Max Cp 1A s or 3A s address to 0 re fer to your T Max user s guide and the sunbed s addres
3. The lamps will turn on and the timer will begin to count down 2 Lift the canopy lie down on the bench face up lower the canopy as Close to your body as possible with no less than 2 between the canopy acrylic and your body 3 When the timer reaches 0 the lamps turn off If you want to stop your session before time expires press the stop button C 4 Raise the canopy by using the outer edge of the canopy do not push up on the acrylic shield as it may crack The cooling fans run for three minutes after the lamps shut off to aid in cooling the sunbed The timer will indicate as a reminder to clean the sunbed After the sunbed is cleaned press the timer button and the display will return to O 4930646 02 Page 6 into the bench Care and Maintenance Cleaning After Use Clean and disinfect your tanning bed s bench and canopy after each use Use a non abrasive disinfectant cleaner that does not contain ammonia or ammonia derivatives Ammonia may damage the acrylic shield Spray the acrylic lightly with disinfectant and wipe dry with a clean soft cloth Thorough Periodic Cleaning The cooling fans draw air through the bed and will cause a dust build up on the lamps and reflectors When a dust buildup is observed it is necessary to thoroughly clean the inside of the bench and canopy 1 Remove the acrylic shields and lamps 2 With a soft cloth wipe the entire length of each lamp 3 Clean both side
4. rounded part of the side skirts points toward the front of the bed Using 2 tree fasteners in each end attach the front skirt panel to the side skirts Simply hold the pieces together lining up the holes and insert the fasteners until they are tight Using the front leg mounting bolt secure the L shaped Skirt Retaining Bracket so it RETAINING BRACKET LS clamps the front and side skirt to the bench cover Place the retainer bracket so the tab holds the front skirt as shown Repeat for the other side 4930646 02 Page 2 Turn bench over Install hinge brackets to ends of bench such that the short boss engages the stud above the bolt hole and the long boss engages the hole below the bolt hole Secure using 5 16 x 1 Allen head bolts and 5 16 metal washers Tighten bolt snug then an additional half turn 8 Place the bushings re into hinge brackets SHORT BOLT lt lt pf S 9 Lift the canopy and hold it between the hinge brackets Insert 5 16 x 1 1 2 bolts with nylon washers into both hinge brackets Tighten bolts into the endcap threaded inserts until snug then an additional half turn Do not overtighten to avoid damaging threaded inserts The gas springs have a locking PIVOT STUD mechanism Follow the directions below for the type you received Type 1 9 Pry back the With a helper holding the canopy locking clip open align ends of gas spring ball
5. not come on The auto start feature of the remote system is disabled see the instructions provided with your remote system My bed connected to a T Max Manager did not display dL but does indicate ugr 1 Remote device has not been set 2 The sunbed has not been connected to the remote system see Remote Connections a tanning time and the lamps have come on 1 Delay time of T Max Manager has not been set 2 Delay time has expired and session has begun a tanning time but the lamps have not come on Auto start function of T Max Manager has been turned off Press the timer button to turn on lamps If you did not find the solution to your problem above contact your place of purchase for additional assistance Proudly manufactured in the U S A 4930646 02 Page 8 SANANANANANANANANANINENENANANINENENANNINENENANENINENENANENENENENANENENENENANENENENENENENENENENENINENENENING LIMITED WARRANTY amp JK Products amp Services JK warrants your tanning unit to be free of structural defects in amp material and workmanship under normal use for its lifetime JK will at its discretion repair 2 any structural defect which materially affects the performance of the tanning unit or replace 5 the tanning unit SS For twelve 12 months following the purchase date of your tanning unit JK will provide re placements for parts that prove to be defective in material or workmanship with the following amp exceptions fluoresc
6. with a flat joints with pivot studs and push screwdriver into place Be sure rod end is down as shown DO NOT lower canopy 8 O until both gas springs are engaged ad a CAUTION H 13 Failure to engage locking clips may Type 2 Lift and lower NSR A few result in the ball joints working loose Remove locking times to lubricate gas springs allowing the canopy to fall which may clip to install or for optimum performance remove gas spring result in damage to the unit and injury REMOTE PORTS REMOTE CONTROL BYPASS PLUG 15 Plug the three prong 220V AC power cord into a dedicated outlet see Electrical Requirements Connect the canopy to bench power cord to the bench receptacle Align the terminals and firmly push on until seated then tighten the threaded locking ring THREADED LOCKING RING The unit is shipped with a Remote Control Bypass Plug installed Your sunbed will not operate without either the bypass plug or a remote system connected If remote operation is desired see Remote Connections REMOTE PORTS ZS WIRED WIRELESS REMOTE REMOTE PORTS RJ 22 PORT RJ 11 4930646 02 Page 3 RECEPTACLE ON BENCH CANOPY TO BENCH POWER CORD Remote Connections Your sunbed incorporates advanced circuitry allowing it to connect and communicate with most remote control systems If a remote system is to be used first determine whether the remote system is a T Max Sys
7. KALA Suen 20 EF Ultraviolet radiation Follow instructions Avoid overexposure As with DAN G E natural sunlight overexposure can cause eye and skin injury and allergic reactions Repeated exposure may cause premature aging of the skin and skin can cer WEAR PROTECTIVE EYEWEAR FAILURE TO MAY RESULT IN SEVERE BURNS OR LONGTERM INJURY TO THE EYES Medications or cosmetics may increase your sensitivity to the ultraviolet radiation Consult physician before using sunlamp if you are using medications or have a history of skin problems or believe yourself especially sensitive to sunlight If you do not tan in the sun you are unlikely to tan from the use of this product Children the elderly or fair skinned people who always burn easily and either never tan or tan minimally should not use this equipment To use lie down on bench and pull canopy down as far as adjustment will allow maintaining at least 2 inches 5 1 centimeters between your body and canopy clear plastic panel otherwise overexposure may occur Do not use without clear plastic panels in place Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approximately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan Skin T
8. TABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH ARE HEREBY amp DISCLAIMED No one has the authority to change or modify this LIMITED Warranty in any respect To obtain service under this LIMITED Warranty contact JK Products amp Services Proof of purchase including serial number is required gt IN NO EVENT SHALL YOUR DISTRIBUTOR OR THE MANUFACTURER BE LIABLE 2 AT LAW OR IN EQUITY FOR ANY LOSS LIABILITY DAMAGE OR EXPENSE IN AN 4 AMOUNT IN EXCESS OF THE PURCHASE PRICE RECEIVED OR FOR LOSS OF USE B OR PROFITS LOSS OF TIME INCONVENIENCE RENTAL OR SUBSTITUTE PROD 2 UCTS LOSS OF BUSINESS LOSS OF INCOME OR ANY OTHER INCIDENTAL INDI amp RECT SPECIAL OR CONSEQUENTIAL DAMAGES Some states do not allow the exclusion B or limitation of incidental or consequential damages and the above limitation or exclusion will 2 not apply to residents of some states This LIMITED Warranty gives you specific legal rights and you may have other rights which may vary from state to state SS JK Products amp Services Inc makes no guarantees on income return on investment market conditions performance etc with any undertaking using its products and services Past per amp formance is not indicative of future results gt All warranty service must be performed by an authorized service person using only JK autho amp rized replacement parts Use of non authorized parts may void your warranty All labor charges must be authorized
9. by JK prior to the start of repairs and must not exceed the established rates and time allotment policies established by JK Contact JK Products amp Services for the amp authorized Service Center nearest you This warranty is serial number specific and only applies amp to tanning units purchased through an authorized JK Distributor This warranty is extended to the individual or legal entity whose name appears on the original sales document and may not amp be transferred to any other individual or legal entity This warranty is void if the tanning unit is modified in any manner from its original design gt To file a Warranty Claim please follow these steps 1 Locate the silver serial number label located on the back of the unit near the power cord on the canopy Identify the serial number and model number of the unit 2 Proof of purchase must be provided before any claim will be considered 3 Contact Perfect Sun at 1 800 449 3605 or visit www PerfectSunTanning com to fill out an online warranty form 4 If it is determined that a defective part needs to be replaced Perfect Sun will arrange for the pick up or shipment of the replacement part
10. ducts e Your sunbed is designed for individual use Always wear the safety goggles supplied with your sunbed or another approved pair of gog gles as defined under 21 CFR 1040 20 Regular sunglasses do not provide adequate protection from ultraviolet light Exposure Times Follow the guidelines for skin type and exposure times as shown in the table below Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tan ning normally appears after the first few sessions and maximizes after approximately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan Skin Type Sensitive Skin Burns easily and severely and does not tan Il Light Skin Burns easily and severely and tans minimally III Normal Skin Burns moderately and tans average IV Dark Skin Burns minimally tans easily and above average RECOMMENDED EXPOSURE TIMES IN MINUTES Level 1 Week 1 Level 2 Level 3 Level 4 1st 3rd Sessions Level 5 Skin Type sensitive NOT RECOMMENDED FOR TANNING Il Light 3 6 10 14 17 Ill Normal 4 7 11 15 17 IV Dark 5 9 13 17 17 MAXIMUM EXPOSURE TIME IS 17 MINUTES 4930646 02 Page 5 Operation A Timer display Displays remaining time B Timer button Turns bed on Timer display shows remaining time If a lesser time is desired press ti
11. ent lamps are warranted against manufacturer s defects for a period of thirty 30 days acrylics are warranted against manufacturer s defects for a period of one 1 year prorated following the purchase date of your tanning unit Standard ground shipping charges amp will be covered for the entire twelve 12 months of this warranty period Any upgraded shipping method charges will be paid for by the customer gt JK also extends to you a one 1 year parts warranty on all T Max remote system components X External voltage transformers buck boosters are covered by a ninety 90 day parts and labor warranty provided you send back the defective transformer S Labor costs associated with repair or replacement work covered by this warranty will be re imbursed for repair or replacement work required to be performed for a period of ninety 90 amp days following the purchase date of your tanning unit Normal wear and tear damage from amp misuse or abuse damage incurred in transit or damages resulting from unauthorized repairs or modifications are not covered by this warranty Warranty coverage does not include cosmetic amp abnormalities such as scratches nicks dents or other cosmetic changes that do not materially B interfere with the function of the tanning unit gt THIS LIMITED WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY OTHER WAR amp RANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MER CHAN
12. lamp products under 21 CFR PART 1040 20 and ANSI UL Standard 482 Disconnect power cord before attempting to clean relamp or engage in the maintenance of this product SVYSUEM DANGER Shock hazard Disconnect power before servicing or removing any protec tive covers Do not operate this device near water or while you are wet Some medications may increase your sensitivity to ultraviolet light It is recommended that you consult a physician before using this sun bed if taking any medication or if you suspect that your skin might be especially sensitive to sunlight WARNING Wear protective eyewear Failure to may result in severe burns or longterm injury to the eyes CAUTION Use of a voltage source over 230V AC may prevent proper operation of the sunbed and could cause damage and void the warranty Air from the room is used to cool the sunbed Maximum ambient room temperature should be 80 F Place your sunbed no closer than 6 from any wall Make sure nothing obstructs the airflow into the sunbed s endcaps or out of the fan openings A poorly ventilated room may cause the unit to become hot and cause discomfort to the user Electrical Requirements Your sunbed operates from a 220V AC source You should have a NEMA L6 30R electrical outlet below on a dedicated circuit capable of providing 30 Amp service installed in the room in which you will use the unit We recommend installation by a professi
13. me control as the T Max Manager eliminating the need for a Man ager If you re using a 1A in this manner it must have a chip labelled master installed on its circuit board The remote control bypass plug must not be used in this configuration The 3A may be used as a mas ter with no modification After you have set the T Max 1A s or 3A s address to 0 refer to your T Max user s guide and the sunbed s address to 1 simply connect the RJ 22 modular cables described in the T Max user s guide directly into either of the smaller ports located on the canopy and either port on the back of the T Max 1A or 3A NOTE A T Max 1A with a master chip can be substituted for a 3A Scenario 7 Non T Max Remote System wired to unit Most non T Max remote systems control the sunbed by the use of a relay The relay operates the sunbed by connecting and disconnecting a pair of wires leading from the sunbed Refer to the user s manual provided with your remote system to determine if it operates in this way To connect your sunbed to this type of system a remote inter face kit is required Contact your place of purchase to obtain the kit The illustration at right details a typical connection Follow the instructions provided with the kit and from the remote s manual to make the necessary connections Non T Max Remote System using control relay ee ee ee Remote Interface Kit
14. mer button until desired time is displayed C Stop button Interrupts tanning session D Face tanner button Units equipped with facial units only Turns face tanner on and off When used without remote or when connected to a remote system using a control relay 1 Press the timer button B to begin the tanning session The timer dis play A displays the remaining time The lamps will turn on and the timer will begin to count down from the maximum tanning session time If a tanning time less than the displayed time is desired repeat edly press the timer button B to decrease the remaining time 2 Lift the canopy lie down on the bench face up lower the canopy as close to your body as possible with no less than 2 between the canopy acrylic and your body 3 When the timer reaches 0 the lamps turn off If you want to stop your session before time expires press the stop button C 4 Raise the canopy by using the outer edge of the canopy do not push up on the acrylic shield as it may crack The cooling fans run for three minutes after the lamps shut off to aid in cooling the sunbed When connected to the T Max Manager or T Max 1A or 3A 1 If the remote system has been set to allow a pre tanning delay time the timer display A will repeatedly flash the delay symbol dL and then the remaining delay time Press the timer button B or wait until the delay time has expired to begin the tanning session
15. n the cano it has to su CAUTION Start pulling from the Be careful The edges of the middei een acrylic shield may be sharp f p L IUU Replacing Lamps To be assured of maximum tanning effectiveness change lamps after approximately 500 700 hours of use Tanning will continue after this time but at a slower rate We recommend using the lamps specified below Use of uncertified lamps is a violation of Federal regulations and may void your warranty 1 Grasp a lamp at one end and at the middle then turn the lamp a quarter turn The lamp may then be gently removed from its holder 2 To reinstall lamp insert pins on the ends of the lamp into the slots on top of the lamp holder and turn the lamp a quarter turn The following lamps have been certified for use in the 28 2F ETS ELITE Warm Tone Model F71 T12 100W BP O below ETS ELITE Plus Model F71 T12 100W BP below Heraeus E400 HPT Facial Lamps o 9 006900002 Removing Replacing Face Tanner Lamps After removing the canopy acrylic shield replace the face tanner lamp as follows Ti 2 Step 1 Support the face tanner assembly with your hand _ while unscrewing the two retaining screws The face L tanner glass casing will swing downward The lamp can now be exchanged The lamp holders are equipped with spring contacts which enable the lamp to be removed easily Remove the old lamp and discard Install the ne
16. o a T Max remote device it may briefly lose communication with the remote This is normal To erase the indicated hours disconnect power from the sunbed Press and hold the green timer button as you reconnect power Release the button after a few seconds Troubleshooting Problem Solution Sunbed not tanning 1 Clean sunbed see Thorough Periodic Cleaning 2 Ensure supply voltage is between 208 and 230V AC 3 Replace lamps if lamp hours are greater than 800hrs 4 Replace acrylic Lamps fail to light and timer display is blank 1 Check source of AC power Reset circuit breaker or replace fuse if necessary 2 Make sure the unit is plugged into outlet Timer display changes to indicate a tanning time after the timer button is pressed but lamps do not come on Bypass plug is not installed see Electrical Connections A bypass plug other than the one sent with your tanning bed has been used If remote is being used other than T Max Manager the external timer may not be activated Remote wiring is incorrect see the instructions provided with the remote interface kit Timer display continues to show a 0 after the timer button is pressed 1 T Max Manager remote system has not yet been set 2 Sunbed address is not set correctly see Remote Connec tions One or more lamps fail to light 1 Check that lamp is installed correctly 2 Switch unlit lamp with a lamp that lights If the new lamp light
17. onal electrician The outlet must be earth grounded 30 AMP NEMA L6 30R RECEPTACLE Hardware Inventory These items and a small pillow r Y Allen head Bolt 5 1 6 x1 Hinge Brackets Quantity 2 1 left 1 right 5 16 Metal Washer Quantity 2 Bushing Hex Allen Wrench Quantity 2 Quantity 1 Allen head Bolt 5 16 x 1 1 2 Quantity 2 niona Safety Goggles QW Oth exec uantity 1 Quantity 2 i i Tree Fastener Quantity 4 Star Lock Washer SRS Quantity 8 10 32 x 1 2 screw p Quantity 8 Skirt Mounting Bracket Quantity 1 left 1 right Skirt Retaining Bracket Ee Quantity 2 4930646 02 Page 1 Assembly Procedures Remove the six 5 16 x 1 bolts and While the bench is upside down attach 1 5 16 washers installed in the bench the triangular skirt mounting brackets Lay the bench upside down on the Attach the stand legs with the four Locate the two brackets and attach them floor Locate the two stand legs small skirt mounting holes toward as shown with two 10 32 x 1 2 screws the back by installing the center bolt and star lock washers Make sure the first You may have to gently push threaded inserts point toward the stand the sides of the legs in to align holes legs and the wide end is toward what Tighten with the Allen wrench will be the floor Attach the side skirts to the mounting brackets with two 10 32 x 1 2 screws and star lock washers from inside the skirt and into the brackets The
18. s and the old lamp still does not replace old lamp The canopy will not stay up NOTE Gas springs are manufactured to hold the canopy in its fully open position as well as allow it to rest fully closed If left open for an extended period of time some creep down may occur This is considered normal Keep the unit closed when not in use If the canopy will not stay fully open when raised Raise and lower the canopy a few times to lubricate gas spring internal seals 2 Replace gas springs 4930646 02 Page 7 Troubleshooting continued Problem Solution My bed won t work with the T Max Manager remote system 1 The sunbed must first be set to a unique address see Re mote Connections 2 The bypass plug may be installed in the series in an inap propriate location Remove bypass plugs when using T Max products When auto addressing the first bed does not register an address When using the auto address feature of the T Max Man ager you must wait 10 seconds from the time you start the auto address function before addressing the first bed forgot what address set my sunbed to By pressing the stop button and then the timer button and holding both for 3 seconds the timer display will show the sunbed s address number Press the stop button to exit ad dress mode My bed is connected to the T Max Manager remote system and when the delay time has expired the timer display starts counting down but the bed lights do
19. s of the acrylic shields with a non ammonia disin fectant cleaner 4 Wipe the reflectors with a clean damp cloth 5 Re install the lamps and acrylic shields Mechanical Inspection Inspect the unit s mechanical integrity every 400 500 hours of use e Inspect the unit s fasteners verifying that all are firmly in place Pay particular attention to the hinge bolts e Inspect gas springs for signs of wear Replace gas springs that will not hold the canopy in the full open position when raised e Inspect the AC power cord and its connections e Inspect the acrylic Replace if broken cracked or badly scratched Removing Replacing Acrylic Shields The acrylic shields are secured in place by hinged profiles which run the length of the bed both front and back Simply pry up on the inside edge of the profile until it releases its latching action see figure below Continue to pry up the profile across its entire length until it swings back freely Repeat for the other profile The long edges of the acrylic shield are now exposed Standing in front of the sunbed grasp the long exposed edge of the acrylic and carefully slide it toward you until it is removed After changing the lamps replace the acrylic shields by reversing the above directions Close the hinged profile by pushing it back into place until it snaps tight acrylic because ort the tanner Do not install the thinner canopy acrylic NOTE The bench acrylic is thicker tha
20. s to 1 simply connect one G2 with Power Injector to the T Max 3A and one G2 to the tanning bed Scenario 3 T Max Manager Series with Wireless combination Wireless can be easily added to an existing salon already utilizing T Max Connect one G2 with Power Injector to the Manager and one G2 to each wireless ready tanning bed The rest of the salon may be daisy chained t together and connected to the Manager lt Non T Max incorporated units Scenario 4 T Max Manager Series with Wireless combination 2 Connect one G2 with Power Injector to the Manager and one G2 to a wireless ready tanning bed The rest of the salon may be daisy chained together and connected to the wireless equipped tanning bed eliminating the need to wire the Manager to the tanning beds C Ti i i _ Non T Max incorporated units Go straight to the source with all your T Max brand remote questions 417 297 0361 4930646 02 Page 4 Scenario 5 T Max Manager Series with wires As always this tanning bed is fully compatible with a wired T Max system Simply connect the RJ 22 modular cable s described in the T Max Manager manual into the remote port s located on the canopy and follow the instructions that came with your remote system T Max Manager incorporated units Scenario 6 Single Bed wired to T Max 3A In single sunbed installations the T Max 1A and 3A can offer the sa
21. tem or a standard remote system operating with a control relay Follow the appropriate instructions for your system type CAUTION The remote connection is not designed to supply or accept high volt age nor can it provide power to an external timer The sunbed s re mote interface circuitry operates on 5 volts attempting to connect it to any higher voltages will damage the sunbed as well as void your warranty T Max Products The T Max remote systems offer the ultimate in sunbed control while allowing the tanner easy straightforward operation Your sunbed is con figured to directly connect to this system including the new wireless remote system The circuitry inside your sunbed eliminates the need for the T Max 1A or 3A when connecting to the T Max Manager series Your sunbed supports the auto addressing feature of the latest T Max Manager models and the following parameters 5 6 7 8 9 10 15 and 23 See your T Max manual for descriptions of these parameters and how they function T Max Wireless Remote System The T Max G2 eliminates wires in your salon allowing easy setup without hiring an electrician to run wires It also protects your invest ment from damage by isolating each unit from one another Your sun bed arrives wireless ready which means it connects directly to the T Max wireless system Older tanning beds and T Max managers also utilize this system but require a T Max Power Injector
22. w lamp using a clean cloth or paper towel Ensure that the lamp is firmly seated in the lamp holders RETAINING SCREWS 2 Step 2 Note Never take hold of the lamp such that your fingers are in contact with the lamp glass Finger oils will greatly reduce the lamp s opera tional life Step 3 Gently close the face tanner glass casing and lock it closed with the screws Ensure that the screws firmly secure the glass casing Unfiltered light from face tanner can cause severe burns Never turn sunbed on while face tanner is disassembled or when glass filters are removed Immediately discontinue use of this equipment if face tanner glass is broken or any unfiltered light can be seen escaping face tanner assembly Hour Counter This sunbed incorporates an ingenious hour counter function into the timing circuitry It allows the operator of the unit to monitor the hours of use of the lamps making it easy to determine when to change them You may also decide to use this function to monitor other time based maintenance tasks To determine how many hours the unit has been in service since the last reset of the hour counter memory first make sure the timer display shows O Then simply hold the stop button for three seconds The display will show two pairs of numbers which indicate the number of hours of service then return to 0 example Display shows 08 then 54 This equals 854 hours NOTE If the unit is connected t
23. ype Sensitive Skin Burns easily and severely and does not tan Il Light Skin Burns easily and severely and tans minimally III Normal Skin Burns moderately and tans average IV Dark Skin Burns minimally tans easily and above average RECOMMENDED EXPOSURE TIMES IN MINUTES Level 1 Week 1 Level 2 Level 3 Level 4 Skin Type 1st 3rd Sessions Sensitive NOT RECOMMENDED FOR TANNING Il Light Level 5 2 4 6 8 11 Ill Normal 3 5 8 11 11 4 6 9 11 11 MAXIMUM EXPOSURE TIME IS 11 MINUTES IV Dark New lamps emit approximately 10 more ultraviolet radiation during the first 50 hours of opera tion Recommended tanning times should therefore be reduced by approximately 10 during that period WARNING Read these instructions before using this sunlamp product All persons in the room should wear protective eyewear when lamps are on Recommended eyewear provided eyeshields or equivalent eyewear as defined under 21 CFR 1040 20 Other types of eyewear may not provide adequate protection Failure to use protective eyewear may result in severe burns or other eye injury If discomfort develops discontinue use and consult a physician THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE 28 2F ETS ELITE Warm Tone Model F71 T12 100W BP O below ETS ELITE Plus Model F71 T12 100W BP below Heraeus E400 HPT Facial Lamps THIS EQUIPMENT MUST BE EARTH GROUNDED This product is in conformity with performance standards for sun
Download Pdf Manuals
Related Search