User Manual - Affordable Scales & Balances
Contents
1. If possible insert the terminal cable D back into the cable channel Turn the balance back over into position The cable can also be led out the back or the side of the weighing platform 0 If you would like to place the terminal farther away from the balance we recommend that you use the extension cable from our accessories range see Section 5 6 Setting up the comparator 15 2 7 Transporting the balance Switch off the balance and disconnect it from the power supply Remove any interface cables from the balance 2 7 1 Transporting over short distances Observe the following instructions to transport your balance over a short distance fo a new location Hold the balance with both hands and lift it Carry the balance to the new location Refer to the notes in Section 2 4 1 regarding selection of an optimum O ii location 2 7 2 Transporting over long distances If you would like to transport or send your balance over long distances or if the balance may not be transported in an upright position use the complete original packaging Setting up the comparator 16 2 8 Weighing below the balance Your balance is equipped with a hanger for carrying out weighings below the work surface weighing below the balance O Il Note For below the balance weighing you will need hook 11132565 from the accessories Sec2. 12 Leveling screws 13 RS232C serial interface 14 Slot for second interface optional 15 Connector for terminal cable 16 Aux 1 connection for ErgoSens hand or foot switch 17 Aux 2 connection for ErgoSens hand or foot switch 18 Power cable 19 Fastening for terminal stand optional 20 Adapter plate with base plate 21 Cover 22 Secondary base 23 Pan support Contents 5 Contents 1 VOUr a Ale a A E E E E E svdeeedsensusveddersaies 6 1 1 TOC WI CHION EE E E E E E E E E E E E E E N 6 1 2 Contents of the Supplementary Operating INSHUCTIONS 0 00 cece ttt ee eee ttteeee cent tieeeeenttieeeeennnteeesentiiieeennnes 6 1 3 y Saa E ootnwyeaetotutu danas E E 6 1 4 Disposal iyere oioi aa T a a E E Oea D E a A EE E A tAE E AE O ERa haddadie 6 2 Setting Up the Comparar ccccseccceseeeesseeeeeseeeeeecesenseeeeensecessneeeensneeessneecesneeesnseeenaneeecesaeesseneesaseneeaseaeensananeas 7 2 Siandaid SCIPS INT 25 ticeda at ite Hidcetataesduaiund a tebanandaicee O A benweaa a E danaadcansaee Mpa anadudddnnnadacetaakdanee ae 7 2 2 Setting up the Comparator Without LEVEIMATIC sssssreirisierriinisisssr niri in T nani ERE NEEE ENNAST REARED NRE HRERS 7 2 2 1 PIGCIAG 1S TORMUNG PEE E E E T N E ES weet E E ainowa ww E T 7 2 2 2 SOMME ME TEACING Ol js sciasisesstacacwins aE varmimnenedionoandousnnhamaagynnntndaoageonanatyseeenamned ra tengaeasuine EA AE 8 2 3 Setting up the Comparator With LEVEIMATIC 0 cece
3. Environmental conditions 19 Selecting the location 11 Equipment 7 Self fest 13 Service 18 F Set it up and prepare 7 Factory setting differences 17 Setting the reading angle 8 Setting up the comparator with Levelmatic 9 G Setting up the comparator without Levelmatic 7 General data 19 Setting up the terminal separately 14 Settings for the XP L comparators 17 l Software 25 Input output devices 25 Special instructions for XP L comparators 17 Installing the balance cable in the terminal 9 Standard equipment 19 Installing the Levelmatic 10 Interfaces 24 T Technical data 19 L Terminal 8 Level sensor 11 Transporting over long distances 15 Leveling Assistant 11 Transporting over short distances 15 Leveling the balance 11 Transporting the balance 15 Load the comparator 17 Location 17 To protect your METTLER TOLEDO product s future METTLER TOLEDO Service assures the quality measuring accuracy and preservation of value of all METTLER TOLEDO products for years to come Please send for full details about our attractive terms of service Thank you P11780871 Subject to technical changes and to changes in the accessories supplied with the instruments Mettler Toledo AG 2006 11780871 Printed in Switzerland 0611 2 12 Mettler Toledo AG Laboratory amp Weighing Technologies CH 8606 Greifensee Switzerland Phone 41 44 944 22 11 Fax 41 44 944 30 60 Internet hitp Awww mt com
4. 8x10 6 Rnt Sensitivity offset sd typical 1x10 Rnt 2x10 Rnt 2x10 Rnt 4x10 Rnt 5x10 Rnt Rgr gross weight Rnt net weight sample weight sd Standard deviation a Year annum D Value out of 5 ABA measurements according to OIML R111 D According to OIML R76 with levelmatic error is negligible d In the temperature range 10 30 C Sensitivity drift year after putting into operation for the first time with the ProFACT self calibration function activated Technical data and accessories 21 5 3 Dimensions XP32003L XP64002L 7 003101 XIILLIN 145 Technical data and accessories 22 5 4 Dimensions XP26003L XP64003L 133 216 5 177 425 280 145 Ozz 5 5 Draft shield dimensions XP W64 Technical data and accessories 23 METTLER TOLEDO 749 5 Technical data and accessories 24 5 6 Accessories You can increase the functionality of your balance with accessories from the METTL
5. Chrome nickel steel X5 Cr Ni 18 10 Plastic chrome nickel steel aluminium and glas Chrome nickel steel and aluminium Balance with country specific power cable Draft shield XP W64 XP26003L XP64003L RS232C interface Protective cover for the terminal Ready for below the balance weighing hook optional Feedthrough for antitheft device Supplementary Operating Instructions this document Standard Operating Instructions for XP Precision Balances Operating Instructions WeighCom Application for XP Comparator Balances Production certificate CE declaration of conformity Technical data and accessories 20 5 2 Model specific data Technical data limit values Model XP26003L XP32003L XP64003L XP64002L XP64002L T Maximum load 26 1 kg 32 1 kg 64 1 kg 64 1 kg 64 1 kg Readability 1 mg 5 mg 5 mg 10 mg 10 mg Repeatability at nominal load ABA measured at 3 mg 26 kg 10 mg 30 kg 8 mg 60 kg 25 mg 60 kg 30 mg 60 kg Repeatability at low load ABA measured at 1 2 mg 1 kg 5 mg 2 kg 4 mg 5 kg 10 mg 5 kg 15 mg 5 kg Electrical weighing range 0 26100 g 0 32100 g 0 64100 g 0 64100 g 0 64100 g Pre load with fullrange 0 1 5 kg 0 1 5 kg 0 2 4 kg 0 2 4 kg 0 2 4 kg Linearity electrical weighing range 25 mg 40 mg 50 mg 50 mg 50 mg Eccentric load deviation measured at 2 0 2 g 8 kg 0 25 g 12 kg 0 35 g 24 kg 0 4 g 24 kg 0 5 g 24 kg S
6. ccc cette centr teen nn iE Eai EEN EEE AEDE GEES SOE Er iR 9 2 3 1 Installing the balance cable in the terminal c cee ccceeceeseeeeeeeeeteeeeescssteeeescsteeeeesctieeeeessitteeeeesssteeeeesestieeeeens 9 2 3 2 INSTAL IMG HE LEVEMMOTIC izcsucnsahecesuns vagcesnanchacdasns a oia Madastabchadendnyes enduws EEEE bands NEE AEN AEAEE 10 2 4 Selecting the location and leveling the balance cc cccccsccccesssteceecsesseeeceeessesesssersseeeseeetseeesesenseeeeesnseeeeeens 1 2 4 1 SELECTING ME IOCOTIOM rurce a E Kn ecsunh tonsa ise denen lahwnsaen Shera oadadisva pease EE E 1 2 4 2 Leveling Mo DGIGMGE sis iaices sa saccteesannsdecdeasbonsdeseaen ealecinaaanwsdeicesapateunted sa ENAKI paws ENERE NETE E TEEN KIER ENERE ER ae ikki 1 2 5 POWEE SUDDIY ssissiszsanavviatannrtsacnsawnuddesatiwrndananleudensual vadeesann ys wadasatieadacn dad E dasiwe dann A OE 13 2 6 Setting up the terminal separately XP32O003L and XP64002L s es aa 14 2 6 1 Removing the terminal and placing it within range of the weighing platform ccc ceeeeeeeeceeeeeeeeteeeeeeeeeeeeeeeees 14 2 7 Transporting the DOIONCe scrise a enei nn a Ee i aE En 15 27l Transporting over short GISTONCES sv snoccssnrescernegs nianna a e a paaa aa E aa a ea aaa 15 2 7 2 TIAMSPOMTING over OMGGISTANCES s csistesvasascdccrsrntereataiswnsqocedunshtnwesesen tence tahahstededuh dais eaesanthdaes TRR TERR ETNAS 15 2 8 WEIGHING BELOW THE DGIGNCE ees spoxaualessapadvacersuniacansyopetoumnn
7. leveling process If you press OK instead the balance will return to the weighing operation The status icon however will continue to be displayed and the warning text will reappear after 15 minutes Setting up the comparator 12 Please choose your actual configuration Forward gt lt Backward Forward gt Press the button that matches your site Remove the weighing pan so you can Turn the leveling foot all the way up in the and your configuration monitor the level indicator direction of the red arrow Now press Forward Now press Forward The red arrow indicates the direction in which you need to turn the footscrews Please press the appropriate button to show the leveling direction Please press the appropriate button to show the leveling direction pf Turn the footscrews in the direction indica ted until the air bubble is in the inner circle of the level indicator If you are unable to do this on your first attempt you can press the button again that matches the current position of the air bubble at any time lt Backward Forward gt Press the button that matches the position of the air bubble in the level indicator As soon as the air bubble is in the inner circle of the level indicator the balance has been leveled correctly left figure leveled correctly right figure leveled incorrectly and you
8. quay aantnate 24 6 e a E E E A EE E E EE A E EE 26 Your XP L Comparator 6 1 Your XP L Comparator 1 1 Introduction Thank you for choosing a METTLER TOLEDO balance To operate the balance you should basically follow the Operating Instructions for Standard XP Precision Balances However in these Supplementary Operating Instructions you will find information about how your balance differs from the Standard XP Precision Balances When working with the WeighCom application use the operating instructions WeighCom Application for XP Comparator Balances that were included with the delivery 1 2 Contents of the Supplementary Operating Instructions These Supplementary Operating Instructions contain the following information Scope of delivery Layout of the balance Installing the Levelmatic and cover Location selection and leveling Power supply Transporting Weighing below the balance Instructions for XP L Comparators Cleaning and service Technical data Accessories Index 1 3 Safety first Always operate and use your balance according to the instructions contained in the Standard Operating Instructions for XP Precision Balances The instructions for setting up your new balance must be strictly observed 1 4 Disposal In conformance with the European Directive 2002 96 EG on Waste Electrical and Electronic Equipment WEEE this device may not be disposed of in domestic wast
9. the weighing process Ensure that the connectors can never come into contact with liquids Once connected to the power supply the balance performs a self test and is then ready for operation Note If the display field remains dark even though the power connection is functioning disconnect the balance from the power supply then check that the terminal cable is inserted correctly see Section 2 6 1 Figure 3 Setting up the comparator 14 2 6 Setting up the terminal separately XP32003L and XP64002L 2 6 1 Removing the terminal and placing it within range of the weighing platform The terminal is connected to the weighing platform with a cable The terminal can be removed from the weighing platform and located separately to ensure the optimum setup of your workplace Setting up the terminal separately Switch off the balance Carefully turn the weighing platform over onto the weighing pan Carefully pull the terminal cable D out of the cable channel Remove the screws A and lift the terminal with terminal support C off the weighing platform Open the housing by pressing the 2 buttons I for adjusting the terminal Unplug the cable K and pull it out of the housing through the opening Remove the 2 knurled screws L and detach the terminal support Pull the cable back through the base of the housing and plug it in Close the terminal and place it in the desired position
10. ER TOLEDO range The following options are available Printer RS P42 Printer with connection cable RS232 for recording results 00229265 BT P42 Bluetooth printer with wireless connection to the balance 11132540 Optional interfaces RS232C second RS232C interface 11132500 LocalCAN Connection for max 5 instruments with LocalCAN connection 11132505 MiniMettler downward compatibility to older devices from METTLER TOLEDO 11132510 PS 2 For connection of commercially available keyboards and barcode readers 11132520 BT Bluetooth For wireless connection of up to 7 peripheral devices 11132530 BTS Bluetooth For wireless connection to a BT P42 printer BT BLD auxiliary display or to a PC 11132535 Ethernet For connection to an Ethernet network 11132515 e Link IP65 EBO1 Ethernet connection to the e Link network with IP65 protection 11120003 Cable for RS232C interface for standard interface or option 11132500 RS9 RS9 m f connection cable for computer or RS P42 printer length 1m 11101051 RS9 RS25 m f connection cable for computer IBM XT or compatible length 2m 11101052 RS9 RS9 m m connection cable for devices with DBY socket f length 1m 21250066 Cable for LocalCAN interface option 11132505 LC RS9 Cable for connecting a PC with RS 232C 9 pin length 2m 00229065 LC RS25 Cable for connecting a printer or PC with RS 232C 25 pin m f length 2m 00229050 LC RS open Cable for connecting th
11. METTLER TOLEDO XP L Comparators XP26003L XP32003L XP64003L XP64002L XP64002L T Supplementary Instructions to the Operating Instructions for XP Precision Balances www mt com support Overview XP L Comparator XP32003L XP64002L 1 Terminal for details s Section 5 Operating Instructions for XP Precision Banlances Display Touch sensitive Touch Screen Operating keys SmartSens sensors Type name Weighing pan Points of attachment for terminal or cover Cover 9 Level indicator level sensor 10 Fastening point for anti theft device 11 Cover plate for below the balance weighing hook optional 12 Leveling screws 13 RS232C serial interface 14 Slot for second interface optional 15 Connector for terminal cable 16 Aux 1 connection for ErgoSens hand or foot switch 17 Aux 2 connection for ErgoSens hand or foot switch 18 Power cable 19 Fastening for terminal stand optional OrNoaoarwWND Overview XP L Comparator XP26003L XP64003L with Levelmatic 1 Terminal for details s Section 5 Operating Instructions for XP Precision Banlances 2 Display Touch sensitive Touch Screen 3 Operating keys 4 SmartSens sensors 5 Type name 6 Weighing pan Levelmatic 7 Points of attachment for terminal or cover 8 Cover 9 Level indicator level sensor 10 Fastening point for anti theft device 11 Cover plate for below the balance weighing hook optional
12. can press the Forward button wv If the balance was leveled correctly the status icon will no longer appear in the upper right hand corner of the display Unscrew the fourth leveling screw until it touches the supporting surface lt Backward Forward gt lt Backward Exit Unscrew the footscrew until it lightly Press the Exit button to exit the Leveling touches the supporting surface Assistant and return to weighing mode Now press Forward Note You can also level the balance at any time without using the Leveling Assistant As soon as the warning message appears press the OK button to cancel the dialogue Level the balance by turning the footscrews as described above As soon as the level is correct the status icon in the upper right hand corner of the display will disappear Setting up the comparator 13 2 5 Power supply Your balance has been supplied with a country specific power cable A A First check to see whether the power plug fits your local power supply connection If this is not the case on no account connect the balance to the power supply but contact the responsible METTLER TOLEDO dealer Connect the balance to the power supply Do not connect the balance to outlets that are not grounded Do not use extension cords without PE conductors Important Guide the cables so that they cannot become damaged or interfere with
13. e This also applies to countries outside the EU per their specific requirements Please dispose of this product in accordance with local regulations at the collecting point specified for electrical and electronic equipment If you have any questions please contact the responsible authority or the distributor from which you purchased this device Should this device be passed on to other parties for private or professional use the content of this regulation must also be related Thank you for your contribution to environmental protection 2 Setting up the comparator 7 Setting up the comparator This Section describes how to unpack your new balance set it up and prepare it for operation On completion of the steps described in this section your balance is ready for operation Note The balance must be disconnected from the power supply when carrying out all setup and mounting AN work as well as when the housing of the weighing terminal is opened during everyday operation 2 1 Standard equipment XP L Comparator Weighing platform Weighing pan 280 x 360 mm XP32003L and XP64002L Levelmatic 220 mm and cover XP26003L XP64003L and XP64002L T Terminal with terminal support XP32003L and XP64002L and protective cover Draft shield XP W64 XP26003L and XP64003L Country specific power cable Supplementary Operating Instructions this document Standard Operating Instructions for XP Precision Balances O
14. e MT ComBus system length 4m 21900640 LC CL Cable for connecting a device with METTLER TOLEDO CL interface 5 pin length 2m 00229130 LC LCO3 Extension cable for LocalCAN length 0 3m 00239270 LC LC2 Extension cable for LocalCAN length 2m 00229115 LC LC5 Extension cable for LocalCAN length 5m 00229116 LC LCT Cable branch T connector for LocalCAN 00229118 Cable for MiniMettler interface option 11132510 MM RS9Ff RS232C connection cable for MiniMettler Interface length 1 5m 00210493 Auxiliary display displays only the weight value and unit if defined RS LC BLD Auxiliary display with RS232 amp LC connection and external power supply with table stand 00224200 RS LC BLDS Auxiliary display with RS232 amp LC connection for table stand or balance stand 11132630 BT BLD bluetooth auxiliary display for wireless connection to balance with BTS interface with table stand 11132555 LC AD Auxiliary display active with table stand 00229140 LC ADS Auxiliary display active with table stand 00229150 Technical data and accessories 25 Input output devices ErgoSens programmable sensor for hands off operation cable length 0 6 m 11132601 LC IO Relay interface with digital inputs and outputs switch eight different devices on and off 21202217 LC FS Foot switch with adjustable function for balances with LocalCAN interface 00229060 LC switchbox connect up to three balances with LocalCAN
15. ensitivity offset 1x10 5 Rnt 1x10 5 Rnt 1 5x10 Rnt 1 5x10 8 Rnt 2x10 Rnt Sensitivity temperatur drift 3 3x10 C Rnt 3x10 C Rnt 3x10 8 C Rnt 5x10 6 C Rnt 1x10 6 C Rnt Sensitivity stability 4 1 5x10 a Rnt 2x10 a Rnt 1 5x10 5 a Rnt 3x10 a Rnt 5x10 5 a Rnt Settling time 8 12s 8 125 8 12s 8 12s 8 125 Interface update rate 23 s 23 s 23 s 23 s 23 s Adjustment built in proFACT proFACT proFACT proFACT proFACT Adjustment with external weights 5 kg 5 kg 10 kg 10 kg 10 kg Weighing platform dimensions W x D x H mm 360 x 280 x 185 360 x 280 x 130 360 x 280 x 185 360 x 280 x 130 360 x 280 x 185 Terminal dimensions W x D x H mm 194 x 133 x 58 194 x 133 x 58 194 x 133 x 58 194 x 133 x 58 194 x 133 x 58 Weighing pan dimensions W x D mm 220 Levelmatic 360 x 280 220 Levelmatic 360 x 280 220 Levelmatic Free space above weighing pan mm 350 350 Weight kg 15 7 10 7 15 7 10 7 25 Draft shield dimensions W x D x H mm 634 x 498 x 620 634 x 498 x 620 Typical data for determination of the measurement uncertainty Model XP26003L XP32003L XP64003L XP64002L XP64002L T Repeatability sd typical 1 5mg 6x10 Rgr 4mg 2x107 Rgr 3 5mg 8x10 Rgr 8mg 3x107 Rgr 12mg 6x107 Rgr Differential nonlinearity sd typical V 5x10 2g Rnt V5x10 g Rnt V 4x10 g Rnt V 8x107 g Rnt V 8x107g Rnt Differential eccentric load deviation sd typical 1x10 6 Rnt 3x10 6 Rnt 1 5x10 Rnt 5x10 6 Rnt
16. interface to a printer 00229220 Barcode reader RS232 21900879 e AC adapter 230V EUR 21900882 e AC adapter 115V USA 21900883 Software LabX pro balance network capable solution for management of weighing data 11120301 LabX light balance management of weighing data made easy 11120317 LabX direct balance simple data transfer 11120340 Freeweigh Net 21900895 MC Link Windows software for comparative weighings 11116504 Various Terminal extension cable length 4 5m 11600517 Wall fixture for terminal 111382665 Protective cover for terminal 111382570 Anti theft device steel cable 11600361 Stand for terminal terminal hight over weighing pan 0 3 m 11132653 Draft shield XP W64 to cover the entire balance W x D x H 498 x 630 x 634 mm 11134470 Hook for the hanger 11132565 Reference weights Reference weight E1 20 kg SCS certified 00159221 Reference weight E1 50 kg SCS certified 00159231 Index 26 6 Index A M Accessories 24 Materials 19 Adjustment 11 Model specific data 20 Auxiliary display 24 0 B Optional interfaces 24 Below the balance weighing 16 Overview 3 4 C P Cable for RS232C interface 24 Placing the terminal 7 Cleaning 18 Power supply 13 19 Contents 6 Printer 24 D Protection and standards 19 Dimensions XP26003L XP64003L 22 R Dimensions XP32003L XP64002L 21 Reference weights 25 Display field remains dark 13 Removing the terminal 14 Disposal 6 Draft shield dimensions XP W64 23 S Safety 6 E Scope of delivery 6
17. mponents which can be cleaned repaired or replaced by the user Please contact your METTLER TOLEDO dealer for details of the available service options Regular servicing by an authorized service engineer ensures constant accuracy for years to come and prolongs the service life of your balance 10 Technical data and accessories 19 5 Technical data and accessories In this Section you will find the most important technical data for your comparator Accessories from the METTLER TOLEDO range increase the functionality and open up additional areas of application see Section 5 7 5 1 General data Power supply e Power supply e Power cable Protection and standards e Overvoltage category e Degree of pollution e Protection e Standards for safety and EMC e Range of application Environmental conditions e Height above mean sea level e Ambient temperature e Relative air humidity Materials e Housing e Terminal e Weighing pan e Draft shield e Levelmatic Standard equipment e Delivered with balance e Documentation 115 240V 15 10 50 60Hz 0 4A 3 core with country specific plug Class II 2 Protected against dust and water IP44 See Declaration of Conformity separate brochure 1 1780294 For use only in closed interior rooms Up to 4000 m 10 30 C 0 5 C 24h 40 at 70 2 Sheet aluminum die cast laquered plastic and chrome steel Die cast zinc chromed and plastics
18. nd unloading the balance 3 3 Settings for the XP L comparators 3 3 1 Factory setting differences compared to the standard types AutoZero Is switched off at initial operation and after a factory reset resetting fo the factory settings but can be switched on again when required When changing over to the WeighCom application AutoZero is automatically switched off When changing back to the Weigh application the previous status of AutoZero is restored A When comparing masses AutoZero must not be switched on because it can distort the measurement values ProFACT Is switched off at initial operation and after a factory reset resetting to the factory settings When comparing masses it is not advisable to switch ProFACT on Cleaning and service 18 4 Cleaning and service Every now and then clean the weighing pan the levelmatic depending on the model draft shield depending on the model housing and terminal of your balance using a damp cloth Your balance is made from high quality durable materials and can therefore be cleaned with a standard mild cleaning agent Please observe the following notes Onno account use cleaning agents which contain solvents or abrasive ingredients as this can result in damage to the terminal overlay Ensure that no liquid comes into contact with the balance or the terminal Never open the balance or the terminal they contain no co
19. nphasnn ENERE apy sca cebupiaedan cov EE EEEE EREEREER 16 3 Special instructions for XP L COMparators c cccceecceeeseeeeeeeeeeeseeeeeeeeeeeeeeeeeeeeesaeeseseaeeeeeeeeescaeeesneeeessaesenenaees 17 3 LOCGTION sviascsansavindadateriudeaansdtansraanas vadendad wena denanaleanennanneyavenluhowanandandee E E EEE E ORES 17 32 toad Me comp pardon aeneon as E a E EEEE E e E E AE 17 3 3 Gellings Tor he XP L COMPGGOMS oscense arn E E E ANR E 17 3 3 1 Factory setting differences compared to the standard types cccccceceeeeeeeeeeeeeeceeeeeeceeeeeeeeeeeeeeeecneetnenteereeeeeees 17 4 Cleaning and SOPVICG sii ese evei ucts ccuensiuee cueveteaseces supaveduuetewsuce webeiese aaas ey dupeetanul aaa aiaiai aiiai 18 5 Technical data Gnd decessores san iseveveesic ctsceed essen e cccteavencensuesevestudsxestappedeeuey cunbecaatecwecte censueehvedeeesstutyenevinuspnnns 19 5 1 General daid sisi vatutainna civcooundateacennasandystinned EAEE eE EAE ETa ET eaaa A a 19 5 2 Model specific data esiseinas aaa a a ae aa a aAa aaa ae a anann 20 5 3 Dimensions AP32003L XPB4AOO2L ocrni eenia ennea aE EEE EEE EEEE E REE AATE E EEEE EENES 21 5 4 Dimensions XP26003L XPG4 OOS L iiss sasussavseauarsseinenanwsdedesenws AEAEE EEEE EEE REEE REEE deaaieuunidinnst tadeinehbsbwaededbeaaasadanes 22 5 5 Dratt shield dimensions XP WGA tis sdcsssnwsumedanawsimensanves sdadansvrnededanods daenssdweiaasnuual EAE EAEAN UEN EEEE NAER 23 5 6 EEEE E e E E E E A E E E E E N E E E E E
20. perating instructions WeighCom Application for XP Comparator Balances Production certificate EC declaration of conformity 2 2 Setting up the comparator without Levelmatic 2 2 1 Placing the terminal il The terminal can be attached to the long or short side of the balance Mount the weighing pan Carefully turn the weighing platform over onto the weighing pan Attaching the terminal to the long side Dismantle the cover B by removing the 2 screws A Setting up the comparator 8 Attach the terminal to the terminal support C as shown using the screws A from the cover that was removed Insert the terminal cable D into the cable channel as shown Screw the connector of the terminal cable into the socket E Turn the balance back over into position Attaching the terminal to the short side Dismanile the cover G by removing the 2 screws F Attach the terminal with terminal support fo the points of attachment H with the screws F Insert the terminal cable D into the cable channel as shown Screw the connector of the terminal cable into the socket E Turn the balance back over into position 2 2 2 Setting the reading angle i ee To change the reading angle press in the two buttons A on the back of the terminal The top of the terminal can then be pulled
21. s B seen b Place the attached adapter plate D on the housing base E Put on the cover F Place the secondary base G on the base plate Put on the pan support H Place the Levelmatic weighing pan I on top Setting up the comparator 11 2 4 Selecting the location and leveling the balance 2 4 1 Selecting the location Select a stable vibration free position that is as horizontal as possible The surface must be able to safely carry the weight of a fully loaded balance Observe ambient conditions see Section 5 1 Avoid the following Direct sunlight Powerful drafts e g from fans or air conditioners Excessive temperature fluctuations If the balance is not horizontal from the beginning it will have to be leveled during initial operation see Section 2 4 2 2 4 2 Leveling the balance Your balance has a built in level sensor that constantly checks the correct horizontal alignment and prompts you to make an adjustment if necessary When the level sensor detects that the level is incorrect the warning text at left will appear and a warning beep will sound A status icon will also appear in the upper right hand corner of the display below the time To level the balance press the Info button This will start the Leveling Assistant The Leveling Assistant will guide you step by step through the
22. tion 5 7 Preparing for below the balance weighing Switch off the balance Disconnect the balance from the power supply Remove any interface cable Remove the Levelmatic depending on the model e Levelmatic weighing pan A e Pan support B e Secondary base C e Cover D e Adapter plate with base plate E Tilt the weighing platform backwards until the cover plate G is visible Remove the 2 screws F and the cover plate G The hanger is now accessible Fasten the hooks optional with screws Then return the balance to its normal position and simply reinstall all components in the reverse order Special instructions for XP L comparators 17 3 Special instructions for XP L comparators To fully utilize the high resolution of the balance some specific rules must be observed These will enable you to obtain the best possible results 3 1 Location Take care to choose a good location see also Chapter 2 4 We recommend you fo operate the balance on a stone bench Other surfaces can have a negative effect on the weighing performance 3 2 Load the comparator Because of the high resolution of the balance even minute differences of temperature or humidity can affect the result Make sure that the weighing pan is clean and that the weighing sample is acclimatized Do not touch the reference and test weights with bare hands Always use gloves or working aids that do not damage the weights when loading a
23. up or down until it engages in the desired position A total of 3 setting positions are available Setting up the comparator 9 2 3 Setting up the comparator with Levelmatic 2 3 1 Installing the balance cable in the terminal Place the terminal on the operating surface Note Ensure that a soft clean surface is used so as not to damage the terminal surface Open the housing by pressing the 2 buttons A for adjusting the terminal and swiveling the housing base upwards Pull the cable with the retaining ring B through the opening on the housing base see diagram Return the terminal fo its normal position and open it so that the cable can be accessed Insert the cable into the top housing C Close both parts of the housing until the retaining ring B is positioned in the cable opening of the housing base Place the retaining ring B behind the two guideways and check that it is secure tension relief Note Before closing the housing always check that the plug is inserted AN correctly into the terminal plug in connection Now close the housing by pressing the two buttons A for adjusting the terminal until the housing base engages in the top housing Setting the reading angle see Section 2 2 2 O Il Setting up the comparator 10 2 3 2 Installing the Levelmatic Attach the base plate A fo the adapter plate C using the 4 ZC screw
Download Pdf Manuals
Related Search