1R/10Amp/24V/T
Contents
1. Grounding option 2 and 3 should be used with caution as for these configurations the controllers positive wires cannot be allowed make electrical contact to the ground or the car frame CAUTION Eco Online Solar Regulator Kit Installation and User Manual Page 18 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved When using Option 3 never mount the regulator near grounded chassis parts and always secure the wires going into the regulator as they could become loose and potentially fall out touching chassis parts WARNING 18 1 Frame Grounding Option Solar Panel FRAME ONLY Ground 18 2 Forbidden Grounding Options Not Allowed Car Chassis Not Allowed Eco Online Solar Regulator Kit Installation and User Manual Page 19 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 19 Specifications Description Nominal System Voltage 12VDC 24VDC Battery Voltage Range 18V 32V Recommended Solar Panel 72 cell NTTV Night Time Threshold Voltage 10V DTTV Day Time Threshold Voltage 12V Maximum Short Term Current Maximum Continuous Current 10A Charge Circuit Voltage Drop Discharge Circuit Voltage Drop Self consumption Temperature Compensation Coefficient Terminal size Operating temperature Storage temperature Humidity Enclosure Regulator Physical Dimensions length 140mm x width 65mm x height 34mm Compensates equalize boost float and low voltage d2. The first choice you have to make is whether you will be connecting your 12V 24V load direct to the battery or through your regulator Solar Charging Setup Options Option 1 Option 2 Load Connection Load Connection Through Regulator Direct To Battery Option 1 Recommended Advantages Option 2 Advantages Regulator will protect the battery from low voltage Regulator and regulator to battery wire need only be deep discharge sized to the maximum power of the solar panels Regulator can control the load running time overnight Option 1 Disadvantages Option 2 Disadvantages Expensive high gauge wire will be needed if you have a No deep cycle protection for the battery high power load and a long battery to regulator distance Needs extra timing devise if you want a timed system You ll need to size your regulator to handle the load Eco Online Solar Regulator Kit Installation and User Manual Page 6 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 7 Recommend Position of Regulator We recommend the regulator be positioned near the battery The regulator should not be mounted in the same compartment as flammable objects or items that can leak flammable gas or vapour such as lead acid batteries solvent gas or oil sources If installing in the same compartment as lead acid batteries there should be WARNING sufficient ventilation Do not allow the regulator to be exposed to rain or moistur
3. DANGER charging instructions Please note panels can produce up to 30 more power than the panels rated power under extraordinary solar conditions EcoOnline recommend de rating the regulator Solar panel wattages and connected loads should not exceed 120W solar power at STC for a 12V system or 7 5Amp continuous load for the 10Amp regulator If appliances are connected to the battery through the regulator WARNING then the total surge start up current from all connected appliances should not exceed the 10Amp rated current for the regulator This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for WARNING their safety Children should be supervised to ensure that they do not play with the appliance This regulator is to be used for charging Sealed AGM Gel or Flooded Lead Acid type batteries only Not to be used for charging any other battery chemistries apart from Lead Acid You should check that the maximum voltage of the charging profile you select does not WARNING exceed the battery manufacturers recommended maximum charging voltage Always use appropriate gauge wires Never exceed the rated Ampacity amp rating of a wire Keep in mind that wires situated in highly insulated environments cannot dissipate heat and
4. Trouble Shooting Guide Firstly connect battery to regulators battery terminals Note battery MUST be at least 6V Does the regulator battery light turn ON Note battery light is typically very faint Battery regulator light turns ON X Battery regulator light stays OFF Next connect solar panel to regulator solar ports Measure voltage across the regulators battery Measure charging current using multi meter connection screws X Solar regulator light X Solar regulator light 0 Volts Measured X Battery voltage stays OFF ON solid NO current Re check battery measured but still no Recheck connection Return regulator to connections amp fuse as regulator lights else return regulator EcoOnline for a OV volts signifies Return regulator to to EcoOnline fora Warranty Claim improper connection EcoOnline for a Warranty Claim and or completely dead Warranty Claim battery Eco Online Solar Regulator Kit Installation and User Manual Page 23 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved
5. cause injury or death if the user does not follow the instructions DANGER Indicates a SAFETY issue that may cause injury or death if the user does not follow the instructions WARNING Indicates a SAFETY issue that may cause injury or property damage if the user does not follow the instructions CAUTION LIN Refers to critically important information related to the correct functioning of the system Read Carefully 7 9 Tip Refers to useful information for the optimal operation of the system Eco Online Solar Regulator Kit Installation and User Manual Page 3 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 2 Safety Requirements Lead acid batteries generate dangerous explosive gases during normal operation always provide adequate ventilation to the outdoors Wear eye protection and gloves at all times when working around lead acid batteries Be mindful of sources of ignition such as sparks DANGER from shorts fuses open flames or cigarettes Note batteries store a large amount of energy Never short circuit a battery s positive and negative terminal Have fresh water available to wash and clean any contact with battery acid When sizing your solar array and battery you must check that the maximum current produced by the chosen solar panel s array can never exceed the maximum allowable charging current for the battery being charged Always follow the battery manufacturer s
6. heavy object can be place on the frame legs Read Carefully to secure again overturning Eco Online Solar Regulator Kit Installation and User Manual Page 13 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 12 Mounting the Charging Regulator Mount vertically Observe Clearance Back heat sink PtP ty ty ty a must have good Cool Air Flow air flow ZISIS SIISII SIII 150mm The controller must be mounted on a vertical non flammable surface in a cool dry sheltered location with adequate ventilation Note the heat sink will get hot under WARNING operation Ensure that there is sufficient air flow around the back of the controller 13 Regulator Connections Use 10mm for 10A Reg Use 13mm for 15 20A Regs When inserting wire into the 10Amp regulator use exactly 10mm bare wire WARNING DO NOT solder these wire tips before connecting to the regulator Soft solder can corrode arch melt and or soften resulting in the cables falling out Unscrew the regulators connection ports fully before inserting wire Make sure the wire is inserted between the regulators gripping teeth and that the connections are tight Loose connections can generate heat due to excessive resistance Make sure there are no WARNING protruding wire strands You should do a pull test to make sure wires can t be pulled out For mobile applications always secure all wiring to a solid surface Unsecured wires and conne
7. regulations in your area We recommend roof mounting of panels be performed by a qualified professional that can advise on appropriate mounting means for your situation WARNING Generally when mounting panel we also recommend e Panel s should be mounted as close to the ground as possible for ease of maintenance reduced wind loading shorter wire runs and a reduced chance of lighting strike e Electrical connections in junction box MUST be soldered on e The underside moisture barrier should not be scratched as this the will severely limit panel lifetime e Donot use self taping screws into the side of frame when installing panels use the bolt holes on the back with locking bolt amp nut set or commercially available mounting means e Panels should be installed with 20mm to 50mm underside ventilation gap 11 2 Portable Folding Solar Camping Panel s We recommend portable folding panels are placed on a secure flat non flammable surface exposed to the sun As a precaution do not place panels on or in dry flammable grass for example WARNING For portable folding panels with a regulator on the back we also recommend you discontinue use if the outside temperature is greater than 40DegC Note the regulator and fuse holder must have air flow during use do not cover system components WARNING LIN We recommend the portable folding panels be put away in very strong wind or if there is a chance of lighting In moderate winds a
8. EcoOnline Timed 12V 24V Solar Regulator For the EcoOnline Solar Kits using the 1R 10Amp 24V T Solar Charge Controller Installation Manual amp User Manual Revised 31 01 2015 La Optex Solar Pty Ltd ww r Tm www EcoOnline com au a Eco Online com au email info EcoOnline com au energy smart solutions Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved This publication is protected by copyright law and unless otherwise specified is for your personal and non commercial use only No part of this publication may be reproduced or distributed by any process electronic or otherwise without the specific written permission of Optex Solar Pty Ltd Trademarks appearing in this manual are the sole property of Optex Solar Pty Ltd or their respective owners Nothing in this publication shall be construed as granting any express or implied license to use any intellectual property of Optex Solar Pty Ltd otherwise than for personal and non commercial use only Optex Solar Pty Ltd must not to the full extent permitted by law be held liable for any claim cost including legal costs damage expense loss including fines penalties set offs and consequential loss or liability arising from the use or misuse of any product described in this publication unless expressly provided otherwise in this publication Information as well as any products described in this publication are subject to change without notice Eco Online So
9. any manual updates and download the latest installation manual from www EcoOnline com au downloads WARNING The following inspections and maintenance tasks are recommended at least two times per year for best controller performance e Check that the controller is securely mounted in a clean and dry environment e Check that the air flow and ventilation around the controller is not blocked Clear all dirt or fragments on the heat sink e Check fixings holding wiring in place e Check all wires to make sure insulation is not damaged from UV exposure frictional wear moisture corrosion fatigue insects or rats etc Maintain or replace the wires if necessary e Make sure all terminal connections are tight Inspect regulator connections for loose corroded broken wires or signs of high temperatures such as discoloured or burnt areas e Confirm that all the system components are ground connected tightly and correctly if the system is grounded e Check that any fuses and fuse holders are not corroded and or lose and or warm or hot during operation Replace as needed Fatigued weathered loose and or corroded wiring or electrical connections poses a fire risk even at low voltage The systems wiring should be checked periodically for any wear cracking resulting from UV damage of insulation on wiring and corrosion of any solder or WARNING controller connections Any affected parts should be replaced at the first sign of damage 22
10. ar panels should be around 21V This should be doubled for a 24V system CAUTION 10 3 In Parallel Connection Using Twin Core Wire for 12V system 12V 12V Parallel Connection A Use cut wire plug to seal 12V 10 4 In Parallel Connection Using Single Core Wire for 12V system 12V 12V Parallel Connection 12V Eco Online Solar Regulator Kit Installation and User Manual Page 11 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 10 5 In Series Connection Using Twin Core Wire for 24V system 12V 12V Connection E E AE 7 Series xy 3 Ss re 1 ff k Use cut wire plug to seal 10 6 In Series Connection Using Single Core Wire for 24V system 12V EF Pry 7 ae l Series Connection For a 24V system the battery voltage must be greater than 18V for the controller to recognize and set the system as a 24V system CAUTION LIN Panels wired in series must be of equal power and face exactly the same direction Panels wired in parallel can face different directions Read Carefully Eco Online Solar Regulator Kit Installation and User Manual Page 12 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 11 Mounting the Solar Panel s 11 1 Mounting on Building Roof or Caravan If the panels are to be mounted on a building roof always check council building
11. close to the battery but no closer than 150mm from the battery terminals WARNING Eco Online Solar Regulator Kit Installation and User Manual Page 8 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved For the battery to regulator wire if you are also connecting the load through the regulator you need to consider max load current not just the max charging current You may need a substantially higher gauge wire WARNING Step 2 Measure and cut the battery to regulator cables For the ve positive line cut the wire at the chosen fuse holder location Strip and tin solder all wires appropriately in preparation for a lap splice follow Section 16 below NOTE Before you solder don t forget to thread all FOUR heat shrink tubes Step 3 Solder the fuse holder in line at both ends using a lap splice Tape down ends to hold in place during soldering Clean flux residue from the solder using suitable solvent Step 4 Use a heat gun to the heat shrink the first sleave You ll need a glove to protect your fingers when you press the hot heat shrink firmly around the wire so that the hot adhesive creates a good Seal Step 5 Use a heat gun to the heat shrink the second sleave The fuse assembly is complete and ready for mounting Note Fuse assembly is only dust proof and should not be exposed to the sun and moisture Fuse assembly and wire should be fixed in place to prevent wire movemen
12. ctions that vibrate or work themselves lose will become resistive which could lead to excessive heating and or fire WARNING Eco Online Solar Regulator Kit Installation and User Manual Page 14 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 14 Wiring and Connection Order Solar Charging Regulator Connection oder DOWDVOS Always power the regulator ON by connecting the battery first before making other connections The regulators light s should come on This will activate the units numerous rotection mechanisms WARNING P When wiring your system never run a 12 24V cable near or in the same compartment or conduit as other 240V cables due to the chance of mistaking the two cables at some later point in time during installation or servicing WARNING AN Depending on the installation we recommend wiring be performed by an experienced and or qualified person such as an electrician WARNING 15 Auto Voltage Selection 12V or 24V System Note the controller will sense and set the system voltage from the battery voltage If the battery voltage is lower than 18V it will recognize the system as 12V If the battery voltage is greater than 18V it will recognize the system as 24V WARNING Eco Online Solar Regulator Kit Installation and User Manual Page 15 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 16 Lap Splice Soldered Connection A solder
13. e WARNING Please note when choosing a location for the regulator it is preferable that the regulator and battery compartments have similar ambient temperature characteristics so that the temperature compensation function on the regulator functions accurately Eco Online Solar Regulator Kit Installation and User Manual Page 7 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 8 Fuse and Technical Wiring Diagrams Wiring Diagram for Wiring Diagram for Load Through Regulator System Load Direct from Battery System Solar Charging Regulator Solar Charging Regulator Fuse The 1R 10Amp 24V T regulator should have a 15Amp fuse You should check with your battery supplier as to the type of fuse to use as some batteries and or banks of batteries connected in parallel are capable of very high short circuit currents and may WARNING require a special current limiting fuse Note the fuse assembly should be close to the battery but no closer than 150mm from the battery terminals WARNING Always use appropriate gauge wires Never exceed the rated Ampacity amp rating of a wire Keep in mind that wires situated in highly insulated environments cannot dissipate heat and hence will have a much lower Ampacity This could lead to a fire hazard WARNING 9 Fuse Assembly Step 1 Choose a conveniently accessible rain sheltered location for the fuse assembly AN Note the fuse assembly should be
14. ed lap splice can be used with this kit to make connection but ONLY for applications where the wiring and splice joins are to be fixed in place WITHOUT potential for tension or repetitive bending movement across splice joins Use ONLY rosin core solder that is WARNING specifically approved for electrical work Overlap area should be at least 3 wire diameters but no more than 5 diameters Wire overlap must be well pre tinned with solder DO NOT nick wire while stripping insulation DO NOT allow solder to diffuse into the length of the wire more than 5 wire diameters from tip Solder the overlapping wire ends together across the entire overlap using sufficient heat to fully melt the solder Tape down ends to hold in place during soldering Clean flux residue from the solder using suitable solvent Cut off any protruding wire strands DO NOT allow movement during the solder solidification process Use a heat gun to heat adhesive lined heat shrink sleave Press ends to seal DO NOT use a naked flame or soldering iron to shrink heat shrink sleave Apply secondary heat shrink sleave to immobilize the splice to protect against metal fatigue of solder Press ends to seal DO NOT expose the stiff splice to tension or metal fatiguing bending forces When mounting soldered splice should be fixed in place at both ends Eco Online Solar Regulator Kit Installation and User Manual Page 16 Copyright 2012 Optex So
15. hence will have a much lower Ampacity This could lead to a fire hazard WARNING If you are unskilled in making safe electrical connections we recommend all electrical connections be carried out by a certified electrician Loose corroded or fatigued electrical connections can become resistive and overheat creating a fire hazard WARNING An appropriate fuse must be installed on the positive regulator to battery connection Some batteries and or banks of batteries connected in parallel are capable of very high short circuit currents and may also require a current limiting fuse You should check with your WARNING battery supplier as to the type of recommend fuse Eco Online Solar Regulator Kit Installation and User Manual Page 4 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved Do not expose this regulator or system components including solder joins to water and or high humidity and or corrosive environments such as those involving marine applications WARNING Always disconnect all connections to the regulator before attempting any maintenance or cleaning to reduce risk of electric shock Note there are no serviceable parts inside the controller do not attempt to repair the controller Incorrect re assembly can cause fire WARNING Only use 12V nominal 36 cell solar panels with this regulator Or 72 cell panel s for a 24V system WARNING What follows are general installation guidelines they s
16. hing e Press Control Button again to toggle through LED number selection e Once selected wait 8 seconds until lights stop flashing Settings are now saved e Repeat to program all three Selection Light types Battery Type Mode amp Timer 1 and Timer 2 20 2 Timer Mode Specifics Timer 1 Timer 2 1r Load OFF r Midnight Hors Before Hours After Load ON Sunset Sunrise Timer 1 When the solar module voltage drops below the Night Time Threshold Voltage NTTV at sunset the controller will turn ON the load after a 10 minutes delay for the specified number of hours Timer 2 The controller will turn the load ON for a specified number of hours before sunrise and turn OFF the load 10 minutes after sunrise when the module voltage reaches the Day Time Threshold Voltage DTTV Note the regulator may take a few days to learn and predict sunrise times 20 3 Mode amp Timer 1 Dusk to Dawn 0 When the solar module voltage drops below the NTTV at sunset the controller will turn on the load after 10 minutes delay When solar module voltage increases above the DTTV the solar controller will turn off the load after a 10 minutes delay Eco Online Solar Regulator Kit Installation and User Manual Page 22 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 21 System Maintenance Important before carrying out any system maintenance you MUST check for
17. hould NOT be taken to be appropriate for all installation situations if in doubt please seek advice from a certified electrician WARNING 3 Warranties EcoOnline offers the following Warranties e 3 year limited Warranty on all Regulators See EcoOnline com au Terms and Conditions page for further details 4 Included Kit Components depending on the kit purchased 10Amp Solar Charging Two core 1 0mm7 1 5mm Single core 2 5 4 mm 10Amp Fuse holder Regulator 5m Solar Wire 10Amp Wire 15Amp fuse kit Eco Online Solar Regulator Kit Installation and User Manual Page 5 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 5 Designing Your Charging System Firstly please visit our online sizing calculators to size your system They will help you understand important factors involved in sizing a solar charging regulator system Do not assume the supplied components are suitable for all situations 1 Solar Panel Sizing Calculator this will help you understand the factors involved in a sizing solar panels 2 Solar Regulator Calculator this will help you understand the factors involved sizing a regulator 3 Solar Wire Sizing Calculator this will help you understand the factors involved in sizing wire gauges A charging system must be sized right for efficiency reliability and safety If in doubt please seek advice WARNING 6 Connecting the Load Direct to Battery or Through the Regulator
18. isconnect voltages SEALED 1 VRSLAB also Sealed or Maintenance free Advanced Glass Mat AGM Liquid Note some wet cell batteries have sealed tops and are marketed as maintenance free however these are still classed as FLOODED type batteries Battery Voltage Charging Parameters at 25 C Charging SEALED GEL FLOODED Equalize Charging Voltage 14 6V 29 2V 14 8V 29 6V Boost Charging Voltage 14 6V 29 2V Float Charging Voltage 13 8V 27 6V Boost Reconnect Charging Voltage 13 2V 26 4V Low Voltage Reconnect Voltage 12 6V 25 2V Under Voltage Warning Voltage 12 0V 24 0V Low Voltage Disconnect Voltage 11 1V 22 2V Discharging Limit Voltage 10 8V 21 6V Equalize Duration Qhours 2 hours Boost Duration 2 hours Under Voltage Warning Reconnect Voltage 12 2V 24 4V 12 2V 24 4V 12 2V 24 4V Eco Online Solar Regulator Kit Installation and User Manual Page 20 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 20 Operating Instructions 4 Mode amp Timer 1 1 Sol 2 Batter r Selection Light Charging Status Light 6 Work Status Light 3 Battery Type 5 Timer 2 Mode Selection Light Selection Light Display Mode amp Timer 1 Fa 2 n p G eit Control a Button Temperature a t Sensor cearvohege Ea EcoOnline como Timed Solar Charge Controller 1 Solar Charging Status Light Indicating Light Charging Status GREEN ON Solid Cha
19. lar Pty Ltd All rights strictly reserved 17 Connector Dismantling Procedure if required main body pin d housing oe A Definitions Step 1 Hold connector by main body unscrew end caps for both connectors use second pliers if required Step 2 With end cap removed hold female connector by pin housing unscrew main body use second pliers if required Step 3 With end cap removed hold male connector by pin housing using a spanner unscrew main body use second pliers if required _ _ Note you may need to compress the main body of the connector to break the glue seal Read Carefully This should be performed by gently compressing the main body using a pair of pliers until vou hear the seal break Note the 10Amp limit for these connectors We recommend connectors are not mounted such that they are continuously exposed to rain and water ingress WARNING Eco Online Solar Regulator Kit Installation and User Manual Page 17 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 18 System Grounding Grounding the regulator is not technically required for simple camping type stand alone solar systems If for some reason grounding is required it should be noted that this is a positively ground regulator See below for allowed grounding configurations CAUTION Grounding Option 1 Sf ok Grounding Option 2 Jf Caution Car Chassis Grounding Option 3 Jf Caution
20. lar Regulator Kit Installation and User Manual Page 1 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved Contents L KYT ater teeters E ero ene cd nnaenenstuaawecnsue toa cones ane odaudanen N 3 E SVU We SOI SUMS 1S a sacs oscreseeeate dats sacociendea eed oaes ranch casesneneastana auicubonetutanotaaeoseventand aaau conansesesieeiaesteves 4 WARTS gies cerry cect sce ecco tees E E E E stare 5 A4 included KIL COMP ONO IIS seser eee E E EEA E EN 5 5 D signing Your Carole Sy SUC a eee eee atc cuteness nT T 6 6 Connecting the Load Direct to Battery or Through the REgulator ccccccccsseccecessececeesececeeeecceeeeeceseeneceeseneeeeeas 6 7 Rec mmend Position OL ROS WAU ON ch cei sree Seance ceteenens sa beste seatc ooa settee te essa lou avannn bos oeene a 7 8 F seand Technical WINS Doe Anns ac decane ntanceaGjacud oases aecenasceaeaneacasaebneasdaiineasuannecdustonsadud E EE ES 8 T gl SL oo 11ST 6 8 6 AY ene nee ee ar nn nS en enone eee eee eee 8 10 SOl PANE AVIEN lt a ee ee re ee ee ee ee eee 10 11 Mounting the Solar Panells tase ceccese ce ctecinces oa cesceec sc uratnceeaeancededsacsncdtoenceuisne en Eea Ea ANE aia 13 12 Mounting the Charging Regulator sssssesssesseresrresssreressrrrssrrreserressreressrrnssrereserresseereserressrerosetreserereseereserereseerese 14 13 Recul or Oe gat s c de 9 Ramee ene eset sea te er mn ore E E E ne ee ee eee eee 14 14 Wiring and Connection OF GEL ccdesncdicaicessseccvarsavce
21. rging normal GREEN Fast flashing Battery over voltage 2 Battery Status Light Indicating Light Voltage Status GREEN Slow flashing Battery Full ORANGE ON Solid Under voltage GREEN ON Solid Battery Normal RED ON Solid Depleted 3 Battery Type Selection Light ON 6 Work Mode Display Charging Mode SEALED 1 GEL 2 or FLOODED 3 4 Mode amp Timer 1 Selection Light ON Timer Mode Timer disabled Dusk to Dawn Load will run all night Load will run for 1 to 15 hours 10min after sunset Test Mode Same as 0 without the 10min delay ON OFF Manual Mode 5 Timer 2 Selection Light ON 6 Work Mode Display Timer Mode Timer disabled Load will run for 1 to 15 hours before sunrise Eco Online Solar Regulator Kit Installation and User Manual Page 21 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved _ _ Notes If Mode amp Timer 1 is set to Dusk to Dawn 0 or Test 16 or ON OFF Mode 17 Read Carefully then Timer 2 will be disabled 6 Work Mode Display Indicating Lights Controller Status Red letter L ON solid Overload or short circuit Red Letter H flashing Controller overheated 20 1 Mode Selection To program the regulators Battery Type and Mode amp Timer and Timer 2 e Press Control Button to toggle through and select the Selection Light you would like to program e Once selected hold down Control Button for 5 second until Work Mode Display starts flas
22. sevenuseesedteokdersesansosdsunbsecoptssaetdduntslecsntecsendaensausiuecesenl hebsevessenteedess 15 15 Auto Voltage Selection 12V or 24V System c cccssesscsossescncosssescouesscueusesensoussectousssencusuessouessencussseneousressenssss 15 16 Lap Splice Soldered COM CCU OU esisin E 16 17 Connector Dismantling Procedure if required cccccccccssseccccceeseeccceeeeeeecceeeeuseececeeeeneceesseeusecceseeeneeeeeseaeenes 17 18 BS a ORINE oca A A 18 19 PECCATO E E E eee ee eee en ee 20 20 ODS ra NS TUTON aa E R E EN 21 21 System MaiINteMance ccscccseccscccscccseecseeceeceuecusceusceuscessceseceseceseccsecesectseetaeeteetaeesaeesseesaueseusseusseussesssesseessenses 23 22 TOUDE OO NS AE eenean E E een nesedeaneesesacoesstnncedesteees 23 Eco Online Solar Regulator Kit Installation and User Manual age Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 1 Key Terms Congratulations on the purchase of your EcoOnline Solar Regulator Kit Please print this manual out for your reference Please take the time to read the manual before starting any work Particular attention should be given to text contained in the following key terms Please note EcoOnline has a strong product safety policy do not install products without reading safety guidelines in the manual Please report any product safety issues or near misses to info EcoOnline com au no matter how trivial Indicates a SAFETY issue that is likely to
23. t and fatigue There should be no flammable objects in contact with or above and below the fuse WARNING assembly If the solder or fuse connections become corroded or fatigued over time resistive heating in these connections can result in a fire Depending on the installation the entire fuse assembly should be placed in an electrical junction box Eco Online Solar Regulator Kit Installation and User Manual Page 9 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved 10 Solar Panel Wiring 10 1 Solar Connection Using Twin Core Wire and Connector for 12V system 5 Cut and strip supplied 2 core solar wire 10Amp max Use male connector Note Choose location of the connection point carefully end on the solar side connectors not for permanent outdoor exposure 10 2 Solar Connection Using Single Core Wire and MC4 Connectors for 12V system Use approved MC4 connector crip tool NEVER screw clamp solder tinned wires to the junction box terminals Positive and negative wires must be soldered onto the solar panels terminals in the junction box WARNING Eco Online Solar Regulator Kit Installation and User Manual Page 10 Copyright 2012 Optex Solar Pty Ltd All rights strictly reserved Always check that the solar modules are wired for the same voltage as the battery by using a multimeter Open circuit voltage of a 12V nominal or 36 cell solar panel or in parallel connected sol
Download Pdf Manuals
Related Search
1R/10Amp/24V/T