Manual
Contents
1. e Always disconnect the power of the log splitter before performing service or replacing parts 13 GB e Never try to split logs larger than the recommended log size capacity Logs must be free from nails or wires which may fly up or damage the machine The log must be cut square in the end and remove also all branches from the trunk Always cut the log in direction of its grain Do not place the log across the splitter it may damage the splitter e Never force the log splitter in more than 5 seconds with the the cylinder under pressure when you try to cut excessively hard wood Overheated oil may damage the machine under pressure Stop the machine rotate the log 90 degrees and try again If the wood still cannot be split it means that the wood s hardness exceeds the capacity of the machine and it must be rejected in order not to damage the log splitter Special warning when using this log splitter Using this powerful tool may create special hazards Take particular care to safeguard yourself and those around you Hydraulic systems Never operate this tool if there is a hazard presented by hydraulic fluid Before using the log splitter check for hydraulic leaks Be sure that the tool and your work area is clean and free of oil spills Hydraulic fluid can create hazards causing you to slip and fall your hands to slip while using the machine or cause a fire hazard Electrical safety Never operate this tool if there is an electrical hazard2. Never operate a log splitter in wet conditions Never operate this tool with an improper electrical cord or extension cord Never operate this tool unless you are able to plug it into a properly grounded outlet which supplies power as stated on the type tag Physical hazards Log splitting creates special physical hazards Never operate this tool unless you are wearing proper safety gloves hard toed shoes and approved eye protection etc Watch out for splitters in order to avoid puncture injury and jamming the tool Never try to split logs which are too large or small to fit properly into the tool Never attempt to split logs containing nails wires or other debris Clean up as you work accumulated split wood and wood chips can create a hazardous work environment Never continue to work in a cluttered work area which may make you slip trap or fall Keep onlookers away from the tool and never allow unauthorized persons to operate this tool NOTICE No list of warning can include everything The operator must use common sense and operate the log splitter in a safe manner Warning As with all machinery there are certain hazards involved with the operation and use Exercising respect and caution will lessen the risk of personal injury considerably However if normal safety precautions are overlooked or ignored it might result in personal injury to the operator or damage of property 14 GB Electric connections Connect the main lead
3. each log splitter is packed in one carton and place the components neatly so that they may be identified and checked for any possible damage during transit Should any component be found damaged please contact your Texas dealer immediately 15 Fig 1 Display of main components Check all components with reference to the following list Log guiding plates Log pusher Operation handle Wheels and shield Oil pump Motor start switch Motor Supporting legs Main frame Wedge TE TOMMOOWS Wheels and leg assembly Unpack the log splitter carefully with the assistance of another person rest it on the polyfoam block packed together with the machine in a box on a supported surface see Fig 2 Place the main frame on the polyfoam block and fix the supporting leg 72 with two bolts 74 and two nuts 73 and tighten it securely see Fig 3 With the main frame supported by the polyfoam block and fixed with the supporting leg you fix the two wheels 112 on the axle of the wheel frame 113 with the axle circlips 111 Afterwards you cover it with the wheel axle covers 110 Please ensure that the wheels are fixed in a balanced position and are able to rotate smoothly see Fig 3 16 Fig2 Polyfoam block Fig3 Wheel frame Supporting leg Polyfoam block GB Fig4 If you by accident place the log splitter as described in Fig 4 the engine fan cover 18 may leave its housing and interfere with the c
4. end 5 sekunder med cylinderen under tryk Overophedet olie under tryk kan beskadige maskinen Det er meget vigtigt at hvis br ndekl veren ikke kl ver i f rste fors g skal du stoppe maskinen og vende br ndeknuden 90 grader Hvis br ndet stadig ikke kan kl ves betyder det at br ndets h rdhed overstiger maskinens evne og br ndet skal afvises s det ikke beskadiger maskinen Anbefalet hydraulisk olie Vi anbefaler f lgende olie til den hydrauliske cylinder Texaco Rando HDZ32 Eller olie med tilsvarende viskositet DK Opbevaring Brendekl veren opbevares et t rt sted Vedligeholdelse Advarsel F r du udf rer vedligeholdelse er det vigtigt at du tager stikket ud af stikkontakten Skift hydraulisk olie Der henvises til anbefalet hydraulisk olie pa tidligere sider i betjeningsvejledningen Se reservedelsliste pa side 10 1 S rg for at brendefremfgreren B har trukket sig helt tilbage 2 Skru oliepinden 10 af og fjern den sammen med O ringen oliepakningen 11 3 Placer en container under brendeklgveren som kan indeholde mindst fire liter olie Tip derefter maskinen for at t mme olien ned i containeren 4 Tip br ndekl veren den anden vej med oliep fyldningshullet opad Brug en ren tragt til at h lde frisk hydraulisk olie i tanken i en m ngde som tidligere beskrevet i betjeningsvejledningen V r sikker p kun at bruge ren hydraulisk olie af h j kvalitet som er lavet specielt til dette
5. the hydraulic cylinder Texaco Rando HDZ32 Or oil with corresponding viscosity 18 GB Storage Store the log splitter in a dry area Maintenance Warning Before performing any maintenance unplug the tool from the power source Changing the hydraulic oil Please see previous pages for recommended hydraulic oil See spare part list on page 21 1 Ensure that the log pusher B is fully withdrawn 2 Unscrew the dip stick 10 and remove it completely together with the O ring oil seal 11 3 Place a container under the log splitter that can hold at least 4 Litre of oil Afterwards tip the machine in order to empty the oil into the container 4 Tilt the log splitter the other way with the oil fill drain port up By using a clean funnel you shall fill with a suitable quantity of fresh hydraulic oil Be sure to use only clean and high quality hydraulic oil specifically made for this purpose 5 Clean the dip stick 10 and insert it in the fuel tank in order to make sure that the oil level is between the two marks on the dip stick 6 Clean the dip stick 10 and O ring 11 thoroughly and reinstall Be careful not to damage the threads of the aluminium oil cover 15 Warning Be sure to dispose the dirty oil properly Bring it to your local waste oil recycling centre Never dump it on the ground or mix it with trash Refilling of hydraulic oil Please inspect the oil level periodically The level must be in between
6. to a standard electrical outlet which equals the specification listed on the type tag name plate WARNING THIS APPLIANCE MUST HAVE A GROUND CONNECTION IMPORTANT The wires in the main lead are colored in accordance with the following code the codes can vary from country to country Green yellow earth Blue neutral Brown live As the colors of the flexible cord of this appliance may not correspond with the colored markings identifying the terminals in your outlet proceed as follows Connect the green yellow cord to the terminal marked with the letter or earth symbol or the color green or green yellow Connect the brown cord to the terminal marked with the letter or the color red Connect the blue cord to the terminal marked with the letter or the color black Extension leads If an extension cable is to be used it is recommended that water proof cables are used and that the connector is kept well clear of any water Since the cable will produce a voltage drop that will prevent the engine from supplying full power and reduce the machine function it is essential that the conductors in the cable conform the following specifications 0 20 meters diameter of conductor 1 5 mm Never use extension cables which are more than 20 meters long If any doubts please consult a qualified electrician Do not attempt any electrical repairs yourself Mounting Remove all components from the packing case make sure
7. v ske kan v re rsag til fare du kan glide og falde dine h nder kan glide n r du bruger maskinen eller der kan v re brandfare Elektrisk sikkerhed Brug aldrig maskinen hvis der er fejl ved det elektriske system Brug aldrig en br ndekl ver under v de forhold Brug aldrig maskinen med en forkert elektrisk ledning eller forkert forl ngerledning Brug aldrig maskinen uden det er tilsluttet en stikkontakt med jordforbindelse som giver den str m der er indikeret p etiketten og er beskyttet af en 16 Amp kredsl bsafbryder Fysiske farer At kl ve br nde skaber s rlige fysiske farer Brug aldrig maskinen medmindre du b rer rigtige sikkerhedshandsker sikkerhedssko og godkendt jenbeskyttelse osv V r opm rksom p tr splinterne for at undg skader eller blokering af v rkt jet Pr v aldrig p at kl ve br ndestykker som er for store eller for sm til at passe ordentligt til maskinen Pr v aldrig p at kl ve br nde som indeholder s m eller andre metalstykker Ryd op mens du arbejder Kl vet tr og tr splinter som flyder rundt kan skabe et farligt arbejdsmilj Forts t aldrig med at arbejde i et rodet arbejdsomr de som kan f dig til at glide eller falde Hold tilskuere v r fra maskinen og lad aldrig personer som ikke har l st betjeningsvejledningen bruge v rkt jet Bem rk Man kan aldrig lave en fuldst ndig liste over advarsler Brugeren skal bruge sin sunde fornuft og benytte maskinen p en sikker
8. 4x12 Main frame Main frame Connection pole Connection pole Log guiding plate Log guiding plate Cross head screw M4x8 Cross head screw M4x8 Bolt M8x10 Bolt M8x10 Nut M8 Locking washer Nut M8 Locking washer Plastic sleeve plate Log pusher assembly Plastic sleeve plate Log pusher assembly Capacitor Capacitor O Ring oil seal O Ring oil seal Anti dust rubber seal Anti dust rubber seal Protection cover Protection cover Capacitor box cover Capacitor box cover Nut M6 Nut M6 Cross head screw Cross head screw Fixing screw M6x18 Fixing screw M6x18 Wire clamp Wire clamp elolelelelelelrm le lm fleleleleEleleJerlelwlwlwlelelelealrns rmleleElelaqrdeErlearirerelIalreJlJe jlreJlre szA r 22 Fluid screw Fluid screw 3 irla IR le liria ele ly lym lwlasfoflelelnfuJeleluo lume lolelelelelnu pl wolfwlwluofeJelde c 5 en 400H Description 520H Amount Description 400H 520H Fluid Nut Guiding rod Fluid Nut Guiding rod Rotate valve cylinder L Copper washer Rotate valve cylinder L Copper washer O Ring oil seal O Ring oil seal Nut cover assembly Nut cover assembly Spring Spring Nut M10 Nut M10 Fluid valve cylinder Fluid valve cylinder Valve sleeve R Valve sleeve R Oil cylinder cover front Oil cylinder cover front Va
9. Fjeder Stempelstang Fjeder Kabel med stik Motorbolt M8 Kabel med stik Motorbolt M8 O Ring olietetning O Ring olietetning Fjederskive 8mm Fjederskive 8mm Stempel Stempel Fladskive 8mm Fladskive 8mm O Ring olietetning O Ring olietetning Motrik M8 Motrik M8 Stempelring Stempelring Skrue M6x8 Skrue M6x8 Cylinderhus Cylinderhus Motorfod gummi Motorfod gummi Oliepind Oliepind Olietetning Olietetning O Ring olietetning O Ring olietetning Deksel for motor front Deksel for motor front Teflon tetningsring O Ring olietetning Teflon tetningsring O Ring olietetning Motrik M8 Skrue 8mm Motrik M8 Skrue 8mm Skrue M3x10 Skrue M3x10 O Ring olietetning O Ring olietetning D ksel for oliecylinder Deksel for oliecylinder Mellemstykke Mellemstykke Bolt Bolt Rund pind 8x25mm Rund pind 8x25mm Lang bolt Lang bolt Lasering Lasering Deksel for ventilator Deksel for ventilator Gearspindel Gearspindel Lasering Lasering Kugle Kugle Bleserhjul Bleserhjul Tandhjul Tandhjul Motordeksel indv Motordeksel indv Muffe for oliepumpe Muffe for oliepumpe Skrue M4x6 Skrue M4x6 Deksel for oliepumpe Deksel for oliepumpe Fjederskive Fjederskive Fladskive 8mm Fladskive 8mm Fladskive Fladskive Fjederskive 8mm Fjederski
10. IOMS svescessscceedssecechurvecvssenscceves saravsbavesivdecvagdescscuieseveserdecevearesteben aa 13 Electri COMMECHIONS assicstsseceusthsuessitesneredtviate dedi sborecstasseemeanucteerter ees das IEEE ENRE 15 Mounting a new machine 5 cc5 scssce siz seessestevevesadeeupecdetenecsunesuctseesassaauey deadeeisdaaveieeseate 15 Clothing viorii ES rar rese 17 Operation and adjustment possibilities 0 0 eee cee eeseeeeceeeeeeeeceeceaeceseeeeeseeeeeeeenaes 17 SII r renerne 19 Maintenance ccsivccociibviataistencsiecvatslhatectecisscaussbiesilbociashicususticeuiued inedivesinestsnvavetslanitetles 19 Technical SpecwiCatiOns oreesa ea E E dave des Erna 20 Trouble ShOOtUnS cides ccscvsesceseees csssesocovsrssseoevea rere a GEE E ECEE EERE 20 Spare part list asics secs cxstesesencesstiadecesbevesssiss vede Eea ARTER NRC A NEEE NERE 22 We congratulate you with the purchase of your new log splitter We are convinced that this machine will fully meet your expectations In order to obtain the maximum gain of your machine you should read this manual very thoroughly This will spare you many unnecessary hassles You shall especially draw attention to information linked to the following symbol When working with the log splitter the safety prescriptions should be followed carefully Read the manual through thoroughly before you start your machine Make sure that you are able to stop the machine and turn off the engine immediately in case of an accident All inst
11. against the wedge J which splits the logs When the logs have been split you shall release both the engine start switch F and the handle C this will allow the log pusher B to withdraw Warning If the log does not split immediately do not force it by maintaining the thrust for more than a few seconds This can damage the tool It is better to try repositioning the log on the splitter or setting the log aside 8 Stack as you are working This will provide a safer working area by keeping it uncluttered you avoid the danger of tripping or damaging the machine 9 Remember to tighten the bleed screw 14 when you have finished splitting Recommended size of wood to be split The diameter of the log is only indicative A small piece of wood can be difficult to split if it has knots or if its fibres are very tough A larger piece of wood can be split if its fibres are smooth and loose Never force the log splitter to split more than 5 seconds with the cylinder under pressure in order to split excessively hard wood Overheated oil under pressure may damage the machine It is very important that if the log splitter does not split in the first attempt please stop the machine and rotate the log 90 degrees If the wood still cannot be split it means that the hardness of the wood exceeds the capacity of the machine and it must be rejected in order not to damage the log splitter Recommended hydraulic oil We recommend the following oil for
12. al 2004 1 Betjeningsvejledning User Manual Br ndekl ver Power Split 400 H Br ndekl ver Power Split 520 H Log splitter Power Split 400 H Log splitter Power Split 520 H Texas Andreas Petersen A S Knullen 2 DK 5260 Odense S Denmark Tel 45 6395 5555 Fax 45 6395 5558 www texas dk post texas dk DK Indholdsfortegnelse Sikkerhedstorskrifter osse er an EE EERE EE EE Elektriske forbindelser 4 55 saerlig eres Opmontering af My Maske 27k Bek ein sis ccin tests sousiaerteteeettsvecsrsiuatadivatesvensdtesutassieueusdes sided reloncesliseespsunennaeudieatws K rsel og justeringsmuligheder rosiner edge Opbevaring stesis ccszesss sesessecavege vecutues seceuees E EEEE EEE EEEE EEEE EEEE NERSE Vedligeholdelse siscrseensseronsn iniii on eanes KEENE EE EEE EEEE EEE EEEE EEEE Tekniske Speciitk atl Omer ssai EAE EER E NERE E ESE Problemi GSM Sass see aen ene EE ENESE SE E EEEN ORN EEE Reseryedelsli ste eneiinuruenorie en ei EREE E E E EAT ERETTE OOWDANAAANY p Vi nsker dig tillykke med din nye br ndekl ver Vi er overbevist om at denne maskine fuldt ud vil opfylde dine forventninger For at opn det maksimale udbytte af din maskine b r du genneml se denne betjeningsvejledning grundigt Det vil spare dig for un dige besv rligheder Du b r is r v re opm rksom p sikkerhedsforskrifterne som er markeret med dette symbol A Ved arbejde med breendeklgveren b r sikkerhedsanvisningerne f lges n je Gennemles
13. betjeningsvejledningen grundigt inden du starter din maskine Veer sikker pa at du omgaende kan stoppe maskinen og slukke motoren i tilf lde af uheld Samtlige instruktioner omkring sikkerhed og vedligeholdelse af br ndekl veren tjener til din egen sikkerhed e En brendeklgver ma ikke bruges til andet arbejde end som beskrevet i betjeningsvejledningen Sikkerhedsforskrifter Brug kun tilbeh r og originale reservedele Montering af ikke godkendte dele kan medf re for get risiko og er derfor ikke lovlig Ethvert ansvar fraskrives ved ulykke eller anden skade som forarsages p g a montering af uoriginale dele F r maskinen tages i brug b r forhandleren eller anden fagkyndig instruere e Den der betjener maskinen er ansvarlig for andre personer i arbejdsomr det Brug aldrig maskinen n r andre is r b rn eller dyr er i n rheden e Mindre rige ma ikke betjene maskinen e B r altid rebeskyttelse jenbeskyttelse briller og arbejdshandsker e Lad aldrig maskinen k re uden opsyn Sluk for str mmen G aldrig fra maskinen f r den er stoppet helt med at k re e Maskinen m kun l nes ud til personer som er fortrolige med betjeningen af maskinen Betjeningsvejledningen skal under alle omst ndigheder medleveres e S rg for at holde dine h nder v k fra br ndeknuden og kilerne hele tiden R r aldrig ved maskinens bev gende dele n r maskinen er t ndt e Br ndekl veren m kun betjenes af personer som er udh
14. du skal frig re br nde der har sat sig fast Pr v ikke pa at frig re breendet ved at sla pa det med et v rkt j Dette kan beskadige motordekslet 53 eller oliepumpedekslet 64 osv Alle beskrevne sikkerhedsregler i ovenn vnte kapitel g lder nar man skal udf re ovenn vnte proces Producenten er ikke ansvarlig for skader p personer dyr eller genstande som opst r ved forkert brug af maskinen eller hvis man ikke im dekommer de beskrevne bestemmelser Specifikationer Br ndekl ver Power Split 400 H Elektrisk MOtol cee 220 V S0Hz 2 850 0 p m eller 2 HK 1200 Watt Max Kraer 4 Ton 8 000 Lbs Br ndest rrelse 370 mm L x 50 250 mm dia Stempelvandring sc 30 mm Hydraulisk olie mengde 2 6 Liter Dimensi0N cccccccceeseeeeeeees 765 L x 300 B x 490 mm H V G sovsen 39 kg Probleml sning Power Split 520 H 220 V 50Hz 2 850 o p m eller 2 HK 1500 Watt 5 Ton 10 000 Lbs 520 mm L x 50 250 mm dia 30 mm 3 1 Liter 920 L x 300 B x 490 mm H 46 kg Der kan opst problemer n r man bruger br ndekl veren og der anbefaler vi at du bruger probleml sningen der er vist i skemaet Hvis processen bliver udf rt af en uautoriseret person g lder garantien ikke og producenten vil blive frataget alt ansvar for skade p personer dyr og genstande PROBLEM MULIG RSAG PROBLEML SNING Br ndet kl ves ikke Br ndet er ikke placeret korrekt Br ndet o
15. form l 5 Rens oliepinden 10 og s t den ned i tanken for at sikre at oliem ngden er imellem de to markeringer p oliepinden 6 Rens oliepinden 10 og O ringen oliepakningen 11 grundigt og s t det p plads V r forsigtig for ikke at beskadige gevindet p d kslet som er af aluminium 15 Advarsel S rg for at bortskaffe den snavsede olie p den rigtige m de Aflever det p din lokale genbrugsstation Smid det aldrig p jorden og bland det aldrig med affald Genopfyldning af hydraulisk olie 1 Du skal j vnligt tjekke oliem ngden M ngden skal v re imellem de to markeringer p oliepinden Hvis oliem ngden er lav skal du efterfylde det anbefalede olie p maskinen Slibning af kilen 1 Efter lang tids brug og n r det er n dvendigt skal kilen slibes ved hj lp af en fin tandet fil fjern forsigtigt eventuelle skaller eller pletter p ggen Hvordan man fjerner br nde der har sat sig fast 1 Udl s begge h ndtag s br ndefremf reren B tr kker sig helt tilbage 2 Inds t en trekantet tr kile under br ndet og f br ndefremf veren til at skubbe kilen ind under br ndet der har sat sig fast 3 Gentag denne proces ved at bruge st rre og st rre kiler indtil br det der har sat sig fast er l st 8 Advarsel DK Du ma aldrig sla pa br nde der har sat sig fast eller fors ge at frig re brendeknuden med dine egneheender nar maskinen k rer Sp rg aldrig andre om hjelp nar
16. g reducere maskinens funktion er det vigtigt at lederne i ledningen har f lgende specifikationer 0 10 meter lederens diameter 2 5 mm Brug aldrig forl ngerledninger som er over 10 meter lange Hvis du er i tvivl kontakt en elektriker Pr v ikke p selv at lave elektriske reparationer Opmontering af maskine Tag alle komponenter ud af pakningen og l g alle komponenterne p nt s de kan identificeres og tjekkes for eventuel beskadigelse under transport Skulle en af komponenterne v re beskadiget skal du kontakte din TEXAS forhandler med det samme Fig 1 Oversigt over de v sentlige komponenter Tjek alle komponenterne med den f lgende liste med reference til Fig 1 Brendefgrerskinner Brendefremfgrer Handtag Hjulstel og sk rm Fig2 Oliepumpe Motor startkontakt Motor St tteben Hovedstel Kile m TATY pS Samling af hjul og st tteben Tag forsigtigt br ndekl veren ud af pakningen med hj lp fra en anden person Placer den p polyskumblokken pakket sammen med maskinen i l kassen p en plan overflade se Fig 2 Fig3 Hjulstel 113 Polyskumblok Placer hovedstellet p polyskumblokken og s t st ttebenet 72 fast med to bolte 74 og to skruer 73 og stram den sikkert se Fig 3 Med hovedstellet st ttet af polyskumblokken og det p satte st tteben p s ttes hjul p stellet af maskinen Ey St tteben 72 S rg for at hjulene er i balance og at de kan rotere j vnt
17. lve sleeve screw lock R Valve sleeve screw lock R Valve housing Valve housing Screw lock R Screw lock R Valve housing screw Valve housing screw Wheel axle cover Wheel axle cover O Ring oil seal O Ring oil seal Axle circlip Axle circlip Screw lock Fixing screw M8x10 Screw lock Fixing screw M8x10 Rubber wheel Wheel frame Rubber wheel Wheel frame Handle base L Handle base L Supporting plate Supporting plate Handle bar Handle bar Flat washer Flat washer Handle knob Handle knob Handle protection guard Handle protection guard Spring L Spring L Hex nut Hex nut O Ring oil seal O Ring oil seal Flat washer Flat washer Nut sleeve Nut sleeve Bolt Bolt NM PDH FRO FR IN Re RE NININ ete lye NIAJ Rte B102 O Ring oil seal O Ring oil seal Note Responsibility can not be accepted for any translation or printing errors We reserve the right to change specification without prior notification Standard delivery specification may require partial self assembly Texas Andreas Petersen A S Knullen 2 DK 5260 Odense S Denmark Tlf 45 6395 5555 E mail export texas dk www texas dk
18. m de Advarsel Som med alt maskineri er der visse risici involveret i brugen af dette produkt Udvisning af respekt og forsigtighed vil formindske risikoen for personlig skade Hvis de normale forholdsregler ikke im dekommes kan det resultere i personlig skade eller beskadigelse af ejendom DK Elektriske forbindelser Forbind hovedledningen til en standard elektrisk stikkontakt som imgdekommer de specifikationer som star pa typeskiltet ADVARSEL DENNE BRAENDEKLOVER SKAL HAVE JORDFORBINDELSE VIGTIGT Ledningerne i hovedledningen er farvet i henhold til den f lgende kode det kan variere imellem forskellige lande og omr der Gr n gul jord Bla neutral Brun str mf rende Hvis farverne p ledningerne p denne maskine m ske ikke svarer til de farvede markeringer som viser polerne p din stikkontakt skal du g re som f lger Forbind gr n gul til polen der er markeret med bogstavet E jordsymbolet eller som er farvet gr n eller gr n gul Forbind den brune ledning til polen der er markeret med bogstavet L eller som er farvet r d Forbind den bl ledning til polen der er markeret med bogstavet N eller som er farvet sort Forl ngerledninger Hvis en forl ngerledning skal bruges anbefales det at bruge vandt tte stik og undga at den kommer i ber ring med vand Da forl ngerledningen vil bevirke et fald i sp ndingen som vil forhindre motoren i at yde fuld kraft o
19. nde der er l ngere end den viste st rrelse Pr v ikke p at kl ve friskt gr nt br nde T rt br nde er meget lettere at kl ve og vil ikke sidde fast i maskinen s tit som friskt br nde vil 3 Placer str mledningen Find en passende stikkontakt og find en passende forl ngerledning hvis n dvendigt L g ledningen i en rute fra br ndekl veren til stikkontakten som sikrer ledningen og sikrer at ledningen ikke bliver beskadiget under arbejdet S rg ogs for at undg v de forhold 4 Placer br ndekl veren sikkert S rg for at kl veren er placeret sikkert p en j vn og st ttet overflade i en h jde p 60 75 cm v k fra genstande der kan forhindre brugerens bev gelse Benyt aldrig kl veren p jorden da der er fare for at den bliver beskadiget af splinter eller stumper og det er heller ikke bekvemt at bruge den i denne position Det anbefales at anvende en fast stander til br ndekl veren Hvis det er n dvendigt kan du blokere hjulene med kiler for at forhindre dem i at rulle 6 DK 5 Abn udluftningsskruen se fig 6 L sn skruen 14 ved at dreje den 3 4 omgange hver gang kl veren bliver brugt Stram skruen igen n r du er f rdig Fig6 udluftningsskrue 14 6 Placering af br ndet p br ndekl veren S t br ndet p kl veren l ngdevist og liggende fladt p hoved stellet I Br ndet skal ligge fladt p br ndekl veren og skal l gges p br ndef rerskinnerne A Pr v aldrig p at kl
20. ooling fan This will produce a machinery noise while working In order to avoid this remove the fan cover from its housing pull it and re position it properly Engine fan cover Fig Handle Handle assembly Locate the handle 97 98 in the box and screw it inside the fixing hole on the handle base 96 and tighten See Fig 5 Place the safety shield on the plate 114 with 2 bots 119 2 discs 118 and 2 nuts 117 and tighten securely Now the log splitter is ready for use Clothing A When working with the machine please wear tight clothing gloves ear protection and boots with non skid soles Operation and adjustment possibilities Please refer to Figure 1 when you follow these instructions 1 Plan your work site Work safely and save efforts by planning your work before hand Place the logs where they can be easily reached Choose a site where you can stack the split wood or load it onto a nearby truck or other carrier 2 Prepare the logs for splitting This log splitter splits wood in the length of 520 mm and a diameter of 50 250 mm When you split larger pieces do not split logs longer than the shown size Never attempt to split fresh green logs Dry logs are a lot easier to split and will not jam as frequently as green logs would 3 Route the power cord Locate an appropriate power outlet and secure an adequate extension cord if necessary Route the cord from the splitter to the power source in a route
21. or 2 HP 1200 Watt or 2 HP 1500 Watt Max POWO ai eina 4 Ton 8 000 Lbs 5 Ton 10 000 Lbs Wood SIZ osse 370 mm L x 50 250 mm dia 520 mm L x 50 250 mm dia Movement of piston 30 mm 30 mm Hydraulic oil amount 2 6 Ltr 3 1 Ltr DimensiON cccccccceeseeeeeeeees 765 L x 300 B x 490 mm H 920 L x 300 B x 490 mm H WEN avs css csscts sins ten test ees 39 kg 46 kg Trouble shooting Problems may arise when you use the log splitter in case of any problems we recommend that you read the trouble shooting part If the process is carried out by an unauthorized person the warranty will not be valid and the manufacturer will not be responsible for any damages on persons animals or objects PROBLEM POSSIBLE CAUSE SOLUTION The log will not be split The log has been placed Place the log correctly incorrectly The log exceeds the approved Split a smaller piece or use other dimensions or the log is too hard remedies to reduce the size of the for the logs ability log The wedge does not split Sharpen the wedge and inspect for burrs and nicks The oil leaks Locate the leakage by using a piece of paper contact your dealer The hydraulic pressure is too low Contact your dealer The log pusher advances jerkily Air in the circuit Inspect the oil level Fill up if or with strong vibrations necessary If the problem continues contact your dealer Oil leaks from the ram
22. or from Leakage in the tank Check that the bleed screw has other external points been tightened before moving the machine fig 6 The oil seal is worn Contact your dealer GB PLEASE READ THE FOLLOWING CAREFULLY ALL REPAIRS AND REPLACEMENTS MUST BE CARRIED OUT BY AN AUTHORIZED DEALER AND NOT BY THE PURCHASER THE PURCHASER ASSUMES ALL RISKS AND LIABLILITIES ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT OF PARTS THERETO OR INSTALLATION OF THESE Spare part list 140 98 112111 A 21 Reservedelsliste Description Description 400H 520H 400H 520H Hex nut M14 Hex nut M14 Wire clamp bushing Wire clamp bushing Hex nut thin M14 Hex nut thin M14 Wire clamp nut Wire clamp nut Piston Ram Piston Ram Cable with plug Cable with plug Spring Spring Engine bolt M8 Engine bolt M8 O Ring oil seal O Ring oil seal Spring washer 8mm Spring washer 8mm Piston Piston Flat washer 8mm Flat washer 8mm O Ring oil seal O Ring oil seal Nut M8 Nut M8 Square piston ring Square piston ring Cross head screw M6x8 Cross head screw M6x8 Cylinder body Cylinder body Engine rubber foot Engine rubber foot Dip stick Dip stick Oil seal Oil seal O Ring oil seal Teflon seal ring O Ring oil seal Teflon seal ring Engine cover front Nut M8 Engine cove
23. r front Nut M8 O Ring oil seal O Ring oil seal Screw 8mm Screw 8mm Bleed screw M3x10 Bleed screw M3x10 O Ring oil seal O Ring oil seal Oil cylinder cover end Oil cylinder cover end Gear housing Gear housing Two head bolt Two head bolt Round pin 8x25mm Round pin 8x25mm Long two head bolt Long two head bolt Spindle circlip Spindle circlip Engine fan cover Engine fan cover Gear spindel Gear spindel Spindle circlip Spindle circlip Rolling ball Rolling ball Flying fanl Engine cover inner Flying fanl Engine cover inner Gear Oil pump sleeve Gear Oil pump sleeve Cross head screw M4x6 Cross head screw M4x6 Oil pump cover Oil pump cover Spring washer Spring washer Flat washer 8mm Flat washer 8mm Flat washer Flat washer Spring washer 8mm Spring washer 8mm Bearing Bearing Bolt M8x55 Bolt M8x55 Rotator Rotator Bolt M8x30 Bolt M8x30 Rolling needle Stator Rolling needle Stator O Ring oil seal CR head screw M6x20 O Ring oil seal CR head screw M6x20 Switch anti dust cover Switch anti dust cover Carry handle Carry handle Switch Switch Supporting leg Supporting leg Switch base Switch base Nut M6 Nut M6 Capacitor support Capacitor support Bolt M6x14 Bolt M6x14 Crosshead screw M4x12 Crosshead screw M
24. rskive Kobberskive O Ring oliet tning O Ring oliet tning M trik M trik Fjeder Fjeder M trik M10 M trik M10 Ventil D ksel for oliecylinder Ventil D ksel for oliecylinder Ventil R Fjeder R Ventil R Fjeder R Ventilhus Ventilhus Sokkel for h ndtag R Sokkel for h ndtag R Skrue for ventilhus Skrue for ventilhus St vh tte St vh tte O Ring oliet tning O Ring oliet tning L seringi L sering L seskrue L seskrue Hjul Hjul Skrue M8x10 Skrue M8x10 Stel for hjul Stel for hjul Sokkel for h ndtag L Sokkel for h ndtag L St tteplade St tteplade H ndtag H ndtag Fladskive Fladskive Knob for h ndtag Fjeder L Knob for h ndtag Fjeder L Sikkerhedssk rm M trik Sikkerhedssk rm M trik O Ring oliet tning O Ring oliet tning Fladskive Fladskive Muffe Muffe Bolt Bolt R IR PN PE IHL ee IYI NTH epee jwlHI Rie O Ring olietetning O Ring olietetning Bemerk Vi p tager os ikke ansvar for evt trykfejl Vi forbeholder os ret til at ndre specifikationer uden forvarsel Standard leveringsspecifikationer kan kr ve at nogle dele skal samles selv Texas Andreas Petersen A S Knullen 2 DK 5260 Odense S Denmark Tlf 6395 5555 E mail post texas dk www texas dk 12 GB Contents Safety PLESCTIPt
25. ructions regarding safety and maintenance of the log splitters are meant for your own safety Safety prescriptions e A log splitter must not be used for other work than as described in the manual Use only accessories and original spare parts Mounting of non approved parts can lead to increased risk of accident Any responsibility at accidents or other kinds of damage caused by mounting of unoriginal parts is renounced e Before the machine is used you shall receive instruction from the dealer The one who operates the machine has the responsibility towards other persons in the working area Never use the machine when others particularly children or animals are close by e Minors must not use the machine e Always carry ear protection eye protection and working gloves e Never let the machine run unattended Shut off the power Never leave the machine until it has come to a complete stop e Only lend the machine to persons who are confident with the operation Always keep the user manual together with the machine e Make sure that your hands are kept away from the log and wedges all the time Never touch the moving parts when the machine is on The log splitter must only be operated by persons who are rested and in good shape If the work is exhausting remember to take breaks on a regular basis Never use the machine under influence of alcohol drugs or medication e Before start always check that bolts and nuts are fastened
26. se Fig 3 Polyskumblok DK Fig4 Hvis du ved et uheld kommer til at placere brendeklgveren som beskrevet pa fig 4 kan ventilatordekslet 18 skubbes og kollidere med ventilatoren Dette kan give stgj nar du bruger maskinen For at afhj lpe dette skal du tage ventilatordekslet af tr k det og s tte det ordentligt pa plads igen Ventilatordzeksel 18 Samling af handtag Figs Find h ndtaget 97 98 i kassen og skru det fast pa Handtag 97 98 soklen for h ndtaget 96 fastspeend det godt Se Fig 5 Set sikkerhedsskermen pa pladen 114 med 2 bolte 119 2 skiver 118 og 2 m trikker 117 fastspeend derefter Nu er breendeklgveren klar til brug Bekl dning A Ved arbejdet med maskinen er t tsiddende arbejdst j solide arbejdshandsker h rev rn og st vler med skridsikre s ler p budt K rsel og justeringsmuligheder Se venligst figur 1 n r du f lger disse instruktioner 1 Planl g hvor du skal arbejde Arbejd sikkert og spar p kr fter ved at planl gge dit arbejde f r du begynder Stil br ndet hvor du let kan n det Hav et sted parat hvor du kan stable det kl vede br nde eller hav en trailer eller andet st ende t t ved hvor det kl vede br nde kan anbringes 2 G r br ndet klar til at blive kl vet Denne br ndekl ver kl ver br nde p en st rrelse i l ngde af max 360mm og en diameter p 50 250mm N r du skal kl ve store stykker m du ikke kl ve br
27. that safeguards the cord and ensures that the cord will not become damaged or wet during the work session 4 Place the splitter securely Please ensure that the splitter is placed firmly on a level and supported surface in a height of 60 75 cm free from any objects to prevent movement of the operator Never operate this splitter on the ground as you will risk it becoming damaged by bits and pieces it is also uncomfortable to work in this position It is recommended to use a permanent stand for the log splitter If necessary you can block the wheels with wedges in order to prevent them from moving 17 GB Fig6 Air bleed screw 5 Open the air bleed see fig 6 Loosen the bleed screws 14 by turning 3 4 times every time you use the log splitter Retighten this screw when you are finished 6 Where to place the log on the splitter Place the log onto the splitter lengthwise and lying flat on the main frame I The log shall lie flat on the splitter and shall be placed onto the log guiding plates A Never attempt to split the log at an angle Be sure that the wedge J and log pusher B touch the end log squarely on the ends 7 Two hand operation When it is safe to start press the engine start switch F with one hand Wait a few seconds while the engine spins up and creates a pressure in the hydraulic pump When it is safe to proceed you press the handle C with both hands The log pusher B will compress the log and push it
28. the two markings on the dip stick If the oil level is too low you shall refill by using a recommended oil Sharpening the wedge After long periods of operation and when it is required you must sharpen the wedge by using a fine toothed file and carefully remove any burrs or flat spots on the wedge How to free jammed logs 1 Release both handles so that the log pusher B will fully withdraw 2 Insert a triangular wedge of wood under the log and activate the log pusher in order to push the wedge under the log which is stuck 3 Repeat this process by using progressively larger wedges until the jammed log is freed 19 GB Warning You must never hammer on the jammed log or place your hands near the log when you attempt to free it Never ask another person for assistance when you are freeing a jammed log Do not try to free the log by hitting it with a tool and keeping the foot blocked this could cause breakage of the engine cover 53 or the oil pump cover 64 etc All the safety rules described in the chapter above apply when carrying out the operations as described above The manufacturer is not responsible in any way for injury of persons or animals or for damage to objects caused by improper use of the machine or failure to comply with the described regulations Specifications Log Splitter Power Split 400 H Power Split 520 H Electric MOtOL eee eeeeeeeee 220 V 50Hz 2 850 r p m 220 V 50Hz 2 850 r p m
29. ve 8mm Leje Leje Bolt M8x55 Bolt M8x55 Anker Anker Bolt M8x30 Bolt M8x30 Not Not O Ring olietetning O Ring olietetning Hus Stovdeksel for kontakt Hus Stgvdeksel for kontakt Skrue M6x20 Handtag Skrue M6x20 Handtag Kontakt Kontakt Ben Ben Kontaktsokkel Kontaktsokkel Motrik M6 Motrik M6 Kondensatorholder Kondensatorholder Bolt M6x14 Bolt M6x14 Skrue M4x12 Skrue M4x12 Stel Stel Tilslutningspol Tilslutningspol Glideskinne Glideskinne Skrue M4x8 Skrue M4x8 Bolt M8x10 Bolt M8x10 Motrik M8 Motrik M8 Plastik glideplade Plastik glideplade Laseskive Laseskive Brendefremfgrer Brendefremf grer Kondensator Kondensator O Ring olietetning O Ring olietetning Gummitetningsring Gummitetningsring Beskyttelsesdeksel Beskyttelsesdeksel Deksel for kondensatorbox Deksel for kondensatorbox Motrik M6 Motrik M6 Skrue Skrue Skrue M6x18 Skrue M6x18 Kabelklemme Kabelklemme elofeledlelelJelrolelrof edie JlJeJlJedleleleleElwolwfluofeleJlJesleslrwslrmofleEeJeJlJeJlJeJyerlrajleJjJaerielreyleJye le laAlry Skrue 11 Skrue lelelelelnslalroflelolalelelru su wlatseo Beskrivelse Beskrivelse 400H 520H 400H 520H M trik M trik Ventil L Ventil L F rerstang F rerstang Kobbe
30. ve br ndet i en vinkel S rg for at kilen J og br ndefremf rer B r rer ved enderne af br ndet 7 Betjen med to h nder Nar det er sikkert at starte skal du trykke p motorstart knappen F med een h nd Vent et par sekunder mens motoren starter op og skaber tryk i den hydrauliske pumpe N r det er sikkert at forts tte skal du trykke de to h ndtag C ned med begge h nder Br ndefremf reren B vil presse br ndet sammen og skubbe det imod kilen J som kl ver br ndet N r br ndet er kl vet skal du slippe de to h ndtag C dette vil f br ndefremf reren B til at tr kke sig tilbage Advarsel Hvis br ndet ikke kl ves med det samme m du ikke tvinge det ved at fastholde trykket i mere end et par sekunder Dette kan skade v rkt jet Det er bedre at pr ve p at placere br ndet p en anden m de p kl veren eller at s tte br ndet v k 8 Stabl mens du arbejder Dette vil give et mere sikkert arbejdsomr de ved at der ikke bliver rodet og du vil forhindre faren for at falde eller beskadige str mkablet 9 Husk at stramme udluftningsskruen 14 n r du er f rdig Anbefalet st rrelse p br nde St rrelsen p br ndets diameter er kun vejledende Et lille stykke br nde kan v re sv rt at kl ve hvis det har knuder og dets fibre er meget st rke Et st rre stykke br nde kan kl ves hvis dets fibre er bl de og l se Tving aldrig br ndekl veren til at kl ve meget h rdt tr i mere
31. verskrider tilladte dimensioner eller br ndet er for h rdt for maskinens evner Kilen kl ver ikke Olien l kker Hydraulisk tryk er for lavt Placer br ndet korrekt Pr v p kl ve et lille stykke eller brug andre midler til at formindske br ndets st rrelse Slib kilen check efter skaller og pletter Find l kagen ved at bruge et stykke papir kontakt din forhandler Kontakt din forhandler Br ndefremf reren k rer frem i ryk eller med st rke vibrationer Luft i kredsl bet Check oliem ngden P fyld hvis n dvendigt Hvis problemet vedvarer skal du kontakte din forhandler Olien l kker fra cylinderen eller fra udvendige punkter L kage i tanken Oliepakning er slidt Tjek at udluftningsskruen er blevet strammet f r du flytter maskinen fig 6 Kontakt din forhandler DK V R VENLIG AT L SE DET F LGENDE GRUNDIGT ALLE REPARATIONER OG UDSKIFTNINGER SKAL UDF RES AF ET AUT SERVICEV RKSTED OG IKKE AF K BEREN K BEREN PATAGER SIG ALLE RISICI OG FARER SOM OPST R VED K BERENS REPARATIONER UDSKIFTNINGER OG INSTALLATIONEN AF DISSE Reservedelsliste 140 1121 11 meh AKS ER J s 10 Reservedelsliste Beskrivelse Beskrivelse DK 400H 520H 400H 520H Motrik M14 Motrik M14 Kabelforskruning Kabelforskruning Motrik tynd M14 Motrik tynd M14 M trik for kabelforskruning Motrik for kabelforskruning Stempelstang
32. vilede raske og i god form Hvis arbejdet er udmattende b r der holdes j vnlige pauser Efter indtagelse af alkohol m der ikke arbejdes med maskinen e Check altid f r start at bolte og m trikker er sp ndt 2 DK Sl altid str mmen fra breendekldveren f r du yder service pa den og udskifter reservedele e Check altid f r start at bolte og m trikker er sp ndt e Kl v aldrig br ndeknuder som er st rre end den anbefalede br ndest rrelse Der m ikke v re s m eller andet metal i br ndet da disse kan beskadige maskinen Br ndet skal sk res retvinklet i enden og alle grene skal fjernes fra tr stammen Sk r altid br ndet i renes retning Du m ikke placere br ndet p tv rs da det kan beskadige br ndekl veren Tving aldrig br ndekl veren til at kl ve meget h rdt tr med cylinderen under tryk i mere end 5 sekunder Overophedet olie under tryk kan beskadige maskinen Stop maskinen og pr v igen ved at dreje br ndeknuden 90 grader Hvis tr et stadig ikke kan kl ves betyder det at h rdheden overskrider maskinens evne og tr et m afvises for ikke at beskadige br ndekl veren S rlige advarsler ved brug af br ndekl ver Hydrauliske systemer Brug aldrig maskinen hvis der er ut thed i det hydrauliske system F r du bruger br ndekl veren skal du tjekke efter for hydrauliske ut theder V r sikker p at din maskine og omr det hvorp du arbejder er rent og frit for oliesplid Hydraulisk
Download Pdf Manuals
Related Search
Manual manual manualslib manual car manuale digitale manually meaning manual timesheet manual transmission manual wheelchair manually update your device drivers windows manual arts high school manual for courts martial manual definition manual labor manual lawn mower manual muscle testing manually register devices with autopilot manual muscle testing grades manualidades manual transfer switch manual therapy cpt code manual blood pressure cuff manual transmission cars for sale manual handling manual digital manual autopilot enrollment