Home

Microcoin

1. OPTO S ARE OK ESC The validator checks the operation of the 3 coin detection opto coupler devices and then reports back their condition If an error message comes up indicating that one or more of the optos are faulty you should check the QL coin path for obstructions If there are no obvious signs of obstruction contact your nearest Microcoin Service Centre for advice Press ESC to return to the main diagnostics menu 5 2 1 Test the Outputs of the Validator Press 2 from the main diagnostics menu to start the output test sequence This test will allow you to turn each of the outputs on and ensure that they are functioning correctly with your equipment TEST OUTPUT LINE 1 6 PUSH 0 FOR ALARM O P PUSH CE FOR GATE ESC e To test the output lines you will need to monitor the voltage on each line See your QL user guide for the pin numbers and voltage levels that correspond to each output for your Model Note Some models of the QL have different numbers of output connection pins and not all lines may be available on these models To signal each line to switch press and release button 1 to activate line 1 button 2 for line 2 and continue until all required channels are tested The outputs will pulse at the time set in the pulse width options for QL Note that the pulse widths may require temporary change to be monitored e To test the alarm line press the 0 button Page 15 Version 1 0 April 2001 Microcoin Micromate User Ma
2. QL configuration REPROGRAM AN EXISTING COIN is used only to renew the average coin signature data of a coin that is already programmed into QL No other settings are changed 4 1 1 Program a New Coin Select 1 Program a new coin from the Program with coin menu ENTER COIN CATEGORY NUMBER 1 TO 12 ESC Enter the coin channel for the new coin Refer to the QL label to ensure you do not inadvertently program over and therefore delete an existing coin channel Use the scroll keys to move to a vacant coin channel Page 10 Version 1 0 April 2001 Microcoin Micromate User Manual CAT 11 ENABLED NO VAL 0 MEDIUM OUTPUT 1 PULSES 0 CHANGE Y N MV SCROLL Configure the selected coin channel by pressing YES and proceed as per instructions for Changing Coin Settings section 3 1 Choose MEDIUM discrimination band this can be adjusted later for greater coin acceptance or elimination of frauds if required When the coin channel settings are correct press NO PASS 10 OR MORE SAMPLE COINS ESC ROLL COIN After you roll the first of the coins the display will change to show the number of coins that have been passed CAT 1 VALUE xxx COIN SAMPLE 1 ESC ENTER AFTER 10 The coin sample number will count the number of coins as they are passed The minimum required is 10 samples but to increase discrimination precision more coins can be passed Press ENTER to finish the programming sequence for that coin ENTER COIN CATEGORY NU
3. and all changes that have been made to the config will be discarded If you select YES the changes will be downloaded QL Page 9 Version 1 0 April 2001 Microcoin Micromate User Manual 4 0 Program a Validator To program new coins into a validator press 3 program new coins from the main menu The Micromate then shows the Program New Coins Menu 1 PROGRAM WITH COINS 2 EXTRACT VAL CONFIG ESC TO EXIT AND SAVE V Scroll to see the other options 3 UPDATE FACTORY CFG 4 PROGRAM A NEW CONFIG ESC M BACK 4 1 To Program a Validator Using Coins To program new coins or tokens into a validator you need to have available a minimum of 10 coins or tokens of each denomination selected from a population at random The 10 coins are used to teach QL the average coin signature and acceptance limits for that coin Passing more coins up to say 25 or the same 10 coins a number of times during programming will increase the discrimination accuracy Note During this explanation the term coin will be used to cover both coins and tokens Press 1 to start the programming procedure The Micromate then downloads the QL configuration and displays the following message while this is being done IDENTIFYING VALIDATOR Once the Micromate gets the information it needs it shows the programming using coins menu 1 PROGRAM A NEW COIN 2 REPROGRAM AN EXISTING COIN ESC SELECT 1 OR 2 PROGRAM A NEW COIN is used to add a new coin to an existing
4. diagnostic modes with the exception of the output line test which is also denied To set a VAL CODE press 2 SECURITY ENTER NEW VALCODE ESC Enter a number that you would like to use as the VALCODE 1 99999 for example 1 2 3 Note If you want to disable the VALECODE feature set the number to 0 As you type an asterisk will appear for each number Press ENTER to set SECURITY ENTER NEW VALCODE kkk ESC You will now be asked to confirm the new code Enter the number again and press ENTER to finish CONFIRM NEW CODE KK ESC If the code is entered correctly you will be returned to the operator setting menu If you wish to clear all the config settings from the validator you can use option 3 WARNING THIS OPTION WILL ERASE THE CONFIG CONTINUE Y N WARNING This option WILL erase all coin settings price settings and operator settings It should not be used unless under instruction from a Microcoin Service representative Pressing YES will cause the Micromate to clear all the config information from QL requiring it to be completely reprogrammed Press NO to return to the setting menu When you have finished making all the required changes through the setting menus press ESC to return to the main menu The Micromate will ask you if you want to program the changes you have made to the config into the validator PROGRAM CHANGES INTO VALIDATOR Y N If you select NO you will be returned to the main settings menu
5. INGS 2 1 Check Coin Settings To check the coin information press 1 COIN SETTINGS O P ON 100 OFF 100 ENTER COIN CATEGORY FLASHING ESC The O P shows the ON and OFF pulse widths of the coin and price output lines in milliseconds ms Allowable range is any value between 0 and 65000ms To check the settings for a coin category enter the coin channel No Refer to QL Label CAT 1 ENABLED Y VAL XXX MEDIUM OUTPUT 1 PULSES 1 ESC MY SCROLL CAT 1 Coin category number 1 12 ENABLED Y Coin is enabled Y or N VAL XXX Value of the coin 0 9999 MED Discrimination window narrow medium wide special OUTPUT 1 Output number 1 6 PULSES 1 Number of pulses for each coin 0 9999 Use the scroll keys to check other coin categories 2 2 Check Price Settings Press 2 to go to the Price Settings PRICE XXX ENABLED Y CLEAR EXCESS N ESC PRICE XXX Price value 0 65000 ENABLED Y Price Enabled Disabled CLEAR EXCESS N Clear excess after price reached Press ESC ESC to return to the main menu Page 5 Version 1 0 April 2001 Microcoin Micromate User Manual 3 0 To Change the Settings in the Validator At the main menu press 2 to bring up the Change Settings Menu The Micromate will then download all of the settings from QL into its memory system 1 COIN SETTINGS 2 PRICE SETTINGS 3 OPERATOR SETTINGS ESC 3 1 To Change the Coin Settings To change the settings of a Coin Press1 and enter the Coin Channel No Refer QL
6. Label ENTER COIN CATEGORY NUMBER 1 TO 12 ESC To check Coin Category 1 for example press 1 ENTER CAT 1 ENABLED Y VAL XXX MEDIUM OUTPUT 1 PULSES 1 CHANGE Y N 4 SCROLL Use the scroll keys to view other coin channels Once you have found the channel you want to change press YES Press Esc to return to the Change Settings Menu ENABLED YES 1 YES 0 NO Press 1 to enable the category 2 to disable it The display will now return to the coin category display with the VAL setting flashing and a CHANGE TO at the bottom CAT 1 ENABLED Y VAL XXX WIDE OUTPUT 1 PULSES 1 CHANGE TO Type in the new value and then press ENTER Allowable Range 0 9999 The options for the discrimination band will now be displayed with the current setting flashing at the top DISC BAND MEDIUM 1 NARROW 2 MEDIUM 3 WIDE 4 SPECIAL ESC SELECT BAND Warning Changing this setting may result in changes to the acceptance of genuine coins and frauds It is recommended that you do not change these settings without consulting Microcoin or one of their authorised distributors To change the current band press the number of the new band required The OUTPUT field will now be flashing CAT 1 ENABLED Y VAL XXX WIDE OUTPUT 1 PULSES 1 CHANGE TO Press the appropriate number for the output line from 1 5 if using the PRICE option or 1 6 if the PRICE is disabled and ENTER to set Refer QL label Page 6 Version 1 0 April 2001 Microcoin Mic
7. MBER 1 TO 12 ESC The display will return to the coin category selection menu to allow you to start programming another coin or to exit by pressing ESC Pressing Esc again will bring up the save changes Option Choose Yes to save the new coin programming 4 1 2 To Reprogram the Coin Signature of an Existing Coin Category From the Main menu press 3 then select 1 to get to the Program with Coins Menu 1 PROGRAM A NEW COIN 2 REPROGRAM AN EXISTING COIN ESC SELECT 1 OR 2 Select 2 to start the procedure Note that this option only resets the average coin signature of an existing coin and assumes you know in which channel the target coin is located If you are unsure refer to the QL label or better still use the Check settings option in the Micromate THIS OPTION RESETS THE COIN SIGNATURE ONLY ESC CONTINUE Y N Press YES to continue Page 11 Version 1 0 April 2001 Microcoin Micromate User Manual ENTER COIN CATEGORY NUMBER 1 TO 12 ESC Enter the number of the category you wish to refresh ie 1 PASS 10 OR MORE SAMPLE COINS ESC ROLL COIN Coin selection and accuracy is as discussed above After the first coin is rolled the display will show the category information and the number of coins rolled CAT 5 VALUE 100 COIN SAMPLE 1 ESC ENTER AFTER 10 The coin sample number will count the number of coins as they are passed The minimum required is 10 samples but to increase discrimination precision mor
8. Microcoin Micromate User Manual Microcoin Table of Contents Essential Information 1 0 2 0 3 0 4 0 5 0 6 0 7 0 Connection and Configuration 1 1 Connection 1 2 Switch On 1 3 Configuration for Use Check the Configuration of a Validator 2 1 Check Coin Settings 2 2 Check Price Settings Change the Settings in a Validator 3 1 Change the Coin Settings 3 2 Change the Price Settings 3 3 Change the Operator Settings Program a Validator 4 1 Program with Coins 4 1 1 Program New Coins and Tokens 4 1 2 Reprogram an Existing Coin 4 2 Transfer a Config 4 2 1 Upload and Store a Config 4 2 2 To Program a Stored Config into a Validator 4 2 3 To Update a Factory Config Diagnostics 5 1 Micromate Diagnostics 5 2 Validator Diagnostics 5 2 1 Testing Outputs 5 2 2 Hardware Tests 5 3 Software Verification Battery Changing Glossary Page 1 U Q D B ONOO anaa AKRWOW N Micromate User Manual Version 1 0 April 2001 Microcoin Micromate User Manual Essential Information Before you use the Micromate a few essential concepts and comments It is strongly recommended that if you read nothing else you at least read this page in conjunction with the Glossary and the Micromate Menu Tree Introduction The Micromate allows a user to check and modify the coin and programming settings in QL It will also enable the programming of new coins and tokens and allow diagnostic tests to be done It
9. The display shows the config designator and serial number and from the source validator and asks if you want to continue Press YES to upload the config into the Micromate EXTRACTING DATA If the config in the target validator has been changed from the factory settings the display will show If the source QL is configured as required ignore this warning and press YES THIS CONFIG HAS BEEN CHANGED FROM THE FACTORY SETTINGS YES TO CONTINUE Once the data is uploaded the display returns to the Program New Coins Menu The uploaded config is stored in memory in the Micromate and can be used to reconfigure any number of QLs Note that the source Config is secure in the Micromate even after power off 4 2 2 To Program a Stored Config into a Validator Once you have a config uploaded to your Micromate you can program it into a target QL Connect the Micromate to the target QL and from the Program New Coins Menu select 4 PGM A NEW CONFIG The Micromate checks the compatibility of the source and target QLs to make sure the configuration is suitable for that QL If the second last digit of the Configs are different the process is aborted If the last digit of the configs are different a warning is displayed In this case it is safe to proceed THIS CONFIG CANNOT BE USED WITH THIS VALIDATOR ESC The display shows the current config in the target QL and the config in the Micromate that is to be downloaded If the details are correct pr
10. User Manual 1 2 Switch On A small switch on the right of the housing just above the keyboard will switch power to the Micromate Once switched on the Micromate goes into a self diagnostic mode and then displays the Main Menu 1 3 To Configure the Micromate for Use To check the set up of the Micromate press 4 to bring up the diagnostics menu 1 MICROMATE 2 VALIDATOR 3 VERIFICATION ESC Press 1 to go to the Micromate set up options VERSION X X 1 COMMS VIA CABLE 2 BACKLIGHT ON ESC V SCROLL VERSION This is the software version number of the Micromate 1 COMMS This is the setting for the communication method with the validator The options available are Press 1 to cycle thru options COMMS VIA CABLE Comms via the supplied RJ11 cable default COMMS VIA PC Comms to a PC not supported yet COMMS VIA I RED Comms via an Infra red link 2 BACKLIGHT The option will turn the backlight on or off Press 2 to toggle states 3 POWER SAVE When the power save option is on the Micromate will shut down after 5 minutes of inactivity Press 3 to toggle states Once the settings are complete press ESC ESC to save settings and return to the main menu Page 4 Version 1 0 April 2001 Microcoin Micromate User Manual 2 0 To Check the Configuration of a Validator Pressing 1 at the Main Menu will bring up the View Settings Menu and allow you to check the configuration information in the QL validator 1 COIN SETTINGS 2 PRICE SETT
11. e coins can be passed After sufficient coins have been passed press ENTER to finish the programming sequence for that coin The display will return to the coin category selection menu to allow you to reprogram another coin or to exit by pressing ESC Press Esc again to save changes 4 2 To Transfer a Config from One Validator to Another There may be times when you want to copy the config from one validator to another This can be done by extracting the config from the source validator and then downloading it to the target validator This will usually take less time than setting up the target validator using the settings menus particularly if there are a number of coin categories configured The transfer will bring all the coin category and user settings to the target validator but new average coin signatures will need to be programmed in for each coin channel in the target validator From the main menu select 3 to get to the Program New Coins Menu 1 PROGRAM WITH COINS 2 EXTRACT VAL CONFIG ESC TO EXIT AND SAVE V Scroll down to see the other options 3 UPDATE FACTORY CFG 4 PROGRAM A NEW CONFIG ESC BACK Page 12 Version 1 0 April 2001 Microcoin Micromate User Manual 4 2 1 Upload and Store a Config from a Programmed Validator To start the process connect the Micromate to the source validator From the Program New Coins Menu select 2 EXTRACT VAL CONFIG PULL CONFIG XXXXX XX FROM VAL XXXX CONTINUE Y N ESC
12. e reprogrammed is with the correct VAL CODE for that validator or by returning the validator to a Microcoin authorised Service Centre to have the code reset Refer Change Operator Settings The verification feature is used to check that the code and config data in the validator have not changed A seed number is chosen by the user and this is applied to an algorithm that calculates a number from the config data and from the ROM code These numbers can then be compared to previous readings or other validators of the same type Refer Software Verification Page 19 Version 1 0 April 2001
13. ed the config in any way you can update your validators with the new version of the config without having to roll coins The updating process will transfer the new information into the validator without modifying the coin signature data Note This operation should only be performed to update the config of a QL with an unmodified factory config and having a Config No exactly the same as the Config being uploaded Connect the Micromate to a QL having the revised Factory Config and extract the Config as described above Connect the Micromate to the target QL and select option 3 update a Factory Config from the Program New Coins Menu TRANSFERING CONFIG PLEASE WAIT After the config has been transferred you will be returned to the programming menu Page 14 Version 1 0 April 2001 Microcoin Micromate User Manual 5 0 Diagnostics Select option 4 from the Main Menu 1 MICROMATE 2 VALIDATOR 3 VERIFICATION ESC 5 1 Micromate Diagnostics The Micromate performs a self diagnostic routine every time it is powered up to ensure that it is functioning correctly The diagnostics menu for the Micromate is used to set the Micromate user options as explained in section 1 3 of this user guide 5 2 Validator Diagnostics From the main diagnostics menu press 2 to bring up the validator diagnostics menu 1 SELF DIAGNOSTICS 2 TEST OUTPUTS 3 TEST HARDWARE ESC Press 1 to start the self diagnostics routine in the validator TESTING
14. ess YES CHANGE VAL CONFIG FROM XXXXX XX TO XXXXX XX ESC YES NO You will be asked to program the coin signatures for the new config The Micromate does not distinguish whether a coin category is used or not and so it cycles through each category showing you the settings and asking if you want to program that coin PROGRAM COIN SIG FOR CAT 1 VALUE 0 ESC YES NO Page 13 Version 1 0 April 2001 Microcoin Micromate User Manual If a coin category has no value press NO to go to the next category PROGRAM COIN SIG FOR CAT 5 VALUE 100 ESC YES NO Once you reach a category that does have a value set up press YES to start programming the coins PASS 10 OR MORE SAMPLE COINS ESC ROLL COIN Pass 10 or more of the appropriate coins for that category and then press ENTER to store the values The details of the next category will then come up Continue to program the coins in to the categories until you have finished all 12 Once all of the coins have been programmed you will need to index up to and including Cat 12 the config will then be downloaded into QL TRANSFERING CONFIG PLEASE WAIT After the config is downloaded the display returns to the main programming menu Press ESC to return to the Program New Coins Menu 4 2 3 To Update a Factory Config Occasionally a new version of a factory config will be issued with updated coin data If you are using validators with the same config and you have not modifi
15. grammed into QL This includes all coin category information and user specified settings as well as other factory specific settings not accessible with a Micromate The discrimination band determines how wide the acceptance window will be for a particular coin or token Typical factory setting is MEDIUM band NARROW WIDE and SPECIAL can also be selected Refer Change the Coin Settings 1 Micromate The Micromate display consists of a 20 character x 4 line LCD fitted with software selectable backlight option Some QL versions are fitted with a single digit LED display For use with Quick Learn on board programming facility Each coin category may be enabled turned on to accept or disabled turned off sometimes referred to as Inhibited by the Micromate Refer Change Coin Settings The validator has a gate which opens to allow valid coins to pass through to the accept chute The Micromate can test the operation of this gate Refer Hardware Tests 2 QL The QL validator has 6 parallel output lines Output lines 1 5 are specific coin output lines Output line 6 is shared with coin output line 6 and the PRICE or credit output line Note that if you select output line 6 and the price output is enabled price setting other than 0 both the Coin and Price outputs will be issued on line 6 simultaneously This situation must be avoided Refer Change Coin Settings The Micromate can also be used to turn on each of the outputs during diagno
16. is provided in a sturdy case to protect against everyday knocks and bumps Validator Power QL needs to be connected to a 12Vdc power source via its parallel port to work with the Micromate Micromate Power The Micromate is powered by an internal battery It also has an input for an external 9Vdc power source which should be used during extended programming sessions to preserve the battery Similarly when working from the battery it is recommended that the Backlight be turned off and that the Power Saving feature be turned on Initial Setup When you first use your Micromate set up the operating modes using the DIAGNOSTICS MICROMATE menu see section 1 3 Menus and Navigation The menu structure of the Micromate is self explanatory and designed to prompt the user for the next entry Take time to read each screen A flashing field indicates that the Micromate is requesting data input Key in the data and press Enter For multiple field entry screens pressing ENTER will skip to the next field without changing the existing value Navigating the menus is accomplished by pressing the appropriate number key for the option listed or pressing ESC to return to the previous menu Pressing ESC multiple times will step back through the menu tree and eventually return you to the main menu Where there are arrows at the bottom of the screen use the scroll arrow buttons to access additional options and information The keypad responds best to slo
17. ntil you return to the diagnostics main menu 5 3 Software Verification The Micromate can perform a comparative verification of the program that is used to operate the validator and the configuration data loaded in to customise the validator for a specific job Note This feature has been included primarily for the regulated Gaming Industry Use in other applications may be limited As part of the verification procedures a seed number is entered and this is used with a CRC check to generate a number This number can then be compared to the verification numbers generated by other validators of the same type to check whether anything is different or changed To verify the validator press 3 from the diagnostics main menu SERIAL NO XXXX SOFTWARE REV X XX CONFIG NO XXXXX XX VERIFY Y N The serial number of the validator will be displayed along with the software revision number and the config number To proceed with the verification press YES Page 16 Version 1 0 April 2001 Microcoin Micromate User Manual VAL S N XXXX ENTER SEED ESC Enter a seed number for example 1 2 3 ENTER CALCULATING PLEASE WAIT SEED 123 The display will now show the results of the verification VAL S N XXXX CONFIG CRC XXXXX ROM CRC XXXXX ESC The Config CRC is the checksum of the seed number and the config data stored in the validator This number can be compared to a previous reading taken from the same valida
18. nual e To test the operation of the gate press the CE button A double click will be heard from the validator indicating that the gate has activated e Once you have completed the output tests press ESC to return to the diagnostic main menu 5 2 2 Validator Hardware Tests The QL validator comes equipped with a multi coloured LED and a switch to aid in diagnosis and on board programming There is also the option of a 7 segment display To test these devices press 3 1 TEST 7SEG DISPLAY 2 TEST LED 3 TEST SWITCH ESC e To test the operation of the 7 segment display press 1 This will signal the validator to display the numbers 0 to 9 on the display Watching the display during this time will allow you to see if the display is working and if any segments are not working e To test the multi coloured LED on the side of the validator press 2 This will cause the validator to pulse the LED first green then red then orange before returning the display to the normal green e To test the operation of the programming switch press 3 PRESS THE SWITCH ON THE VALIDATOR Press the programming switch within 30 seconds and the display will show that the switch is OK SWITCH OK If the switch fails or you don t press it within 30 seconds a warning display comes up SWITCH FAILED TO OPERATE If the switch is faulty contact a Microcoin Authorised Service Centre Once you have concluded the hardware tests press ESC u
19. oin Channels has the following information associated with it Coin Value Output Line No of pulses Enabled or Disabled status and Discrimination Band Refer Check Coin Settings This is a number generated by an algorithm within QL that uses both the seed number chosen by the user and the CRC number which is calculated from the software code The checksum can be used to verify that the code and configuration in a validator hasn t changed or that the code in different validators is the same Refer Software Verification Excess credit is generated when the accumulated value of coins accepted exceeds the pre set totalised price or credit value Excess credits can be retained or cleared after the accumulated price output Any retained excess credits will stored in QL as long as it has power Refer Change Price Setting The Coin Signature is a set of values generated within QL for a particular coin when a coin passes through the detect area The Average Coin Signature is a set of numbers stored within QL which represents the average of the coin signatures for a population of those coins The average coin signature is used to form a window of acceptance that a coin signature must fall within to be considered valid Both of these values are specific to any particular QL This setting refers to the physical mode of communication between the Micromate and QL Refer Configuration For Use The CONFIG or configuration file contains all the information pro
20. r Settings 1 COIN SETTINGS 2 PRICE SETTINGS 3 OPERATOR SETTINGS ESC From the Change Settings Menu press 3 to go to the Operator Settings Menu 1 OUTPUT PULSE TIME 2 SET VAL CODE 3 CLEAR ALL SETTINGS ESC Setting 1 allows you to change the output pulse width and spacing for the coin and PRICE outputs Press 1 to bring up the pulse time menu The ONTIME setting will be flashing ONTIME 100 OFFTIME 100 CHANGE TO To change the pulse on time key in the new value eg 50 then press ENTER The ONTIME setting will now show your new setting and the OFFTIME setting will be flashing ONTIME 50 OFFTIME 100 CHANGE TO Key in the new value for the OFFTIME or spacing between the output pulses eg 50 then press ENTER The new settings will be displayed and you will be asked if you want to make any more changes to the new settings ONTIME 50 OFFTIME 50 ANY MORE CHANGES Y N Press YES if you want to go back and change the settings Press NO to keep the new settings and return to the operator settings menu 1 OUTPUT PULSE TIME 2 SET VAL CODE 3 CLEAR ALL SETTINGS ESC To secure a validator against unauthorised changes you can enter a user or VAL CODE The VAL CODE is chosen to allow an authorised user to access the change settings menus but prevent Page 8 Version 1 0 April 2001 Microcoin Micromate User Manual unauthorised changes When enabled the Micromate can access only read only functions and the
21. romate User Manual Note that if you select output line 6 and the price output is enabled price setting other than 0 both the Coin and Price outputs will be issued on line 6 simultaneously This situation must be avoided The PULSES will now be flashing CAT 1 ENABLED Y VAL XXX WIDE OUTPUT 1 PULSES 1 CHANGE TO Type in the number of pulses required 1 9999 and press ENTER The Micromate will now ask if there are any more changes required If you press YES you will be returned to the coin channel you have just edited Pressing NO will return you to the Coin Category selection menu where you can use the scroll keys to select other coin channels to edit When your changes are completed press ESC ESC to return to the main menu You will then be asked if you want to program the changes into the validator PROGRAM CHANGES INTO VALIDATOR Y N Pressing YES will tell the Micromate to download the new settings to the validator Pressing NO will delete all changes to the settings and the validator will not be reprogrammed 3 2 To Change the PRICE Settings The PRICE or Credit totalizer accumulates the value of the coins and tokens accepted by QL until the set Price or credit is reached where upon it issues a pulse on output line 6 The CLEAR EXCESS option determines what happens to any stored credit in excess of the PRICE value If the CLEAR EXCESS option is enabled any stored credits will be cleared If the CLEAR EXCESS op
22. stic testing Refer Hardware Tests Page 18 Version 1 0 April 2001 Microcoin Micromate User Manual OUTPUT PULSE WIDTH POWER SAVING PRICE PULSES VALUE VAL CODE VERIFICATION The output pulse width is the duration of the pulses issued on coin lines 1 6 Both the ON time and the OFF time time between multiple pulses can be specified in mSec Range 0 9999 Refer Change Operator Settings When the power save option is turned ON the Micromate switches itself off after 5 minutes of inactivity Refer Micromate Diagnostics The PRICE Credit totalizer accumulates the value of the coins and tokens accepted by QL until the set Price Credit is reached where upon it issues a pulse on output line 6 Range 0 65000 Refer Change the Price Settings The number of pulses issued on a coin output line for each of the Coin Channels can be programmed by the Micromate Range 0 9999 Refer Change Coin Settings Value of the coin or token in a particular Coin Channel Used in conjunction with the Price setting Generally specified in decimal value ie 1 100 Range 0 9999 Refer Change Coin Settings The VAL CODE is a user defined access code stored within QL to prevent un authorized changes to QL As the code is stored in QL it is validator specific and independent of the Micromate Note If you are going to use the VALCODE feature it is very important to keep records of the code used Once a VALCODE is set the only way the validator can b
23. tion is disabled any stored credits will be saved and further pulses issued until the value of the stored credit is less than the price setting To modify the PRICE settings from the main menu press 2 CHANGE SETTINGS The Micromate will interrogate the validator retrieve the settings and display the change settings menu 1 COIN SETTINGS 2 PRICE SETTINGS 3 OPERATOR SETTINGS ESC Press 2 PRICE SETTINGS to display the current settings with the PRICE flashing PRICE XXX ENABLE Y CLEAR EXCESS NO CHANGE TO To change the PRICE setting enter the new value required 0 65000 and then press ENTER If you wish to disable the PRICE enter a value of 0 This will cause the ENABLE display to change to ENABLE N to confirm the disabling of the PRICE option The CLEAR EXCESS will now be flashing PRICE XXX ENABLE Y CLEAR EXCESS NO 1 YES 0 NO CHANGE TO Press 1 to clear the excess or 0 to save it Page 7 Version 1 0 April 2001 Microcoin Micromate User Manual The settings you have selected will now be displayed and you will be asked whether you want to make any changes to the settings as displayed or to accept them and program them into the validator PRICE XXX ENABLE Y CLEAR EXCESS NO ANY MORE CHANGES Y N If you press YES you will be taken back to the price setting Menu If you press NO the changes will be programmed into the validator and you will be returned to the settings menu 3 3 To Change the Operato
24. tor or from another validator with the same config to see if there are any changes in the code The ROM CRC is the checksum of the seed number and the program software in the validator and can be used to verify that there haven t been any changes to the operation of the validator 6 0 To Change the Battery Ensure the micromate is turned off and disconnect all cables Unscrew the 4 screws on the back cover of the Micromate Holding the Micromate horizontally face down CAREFULLY lift the back cover off the unit Unplug the existing battery and replace it Check the PCB and end cover to ensure they are in position and then replace the back cover screwing up the 4 screws Always use an Alkaline 9V battery as a replacement Note Please dispose of used batteries carefully Page 17 Version 1 0 April 2001 Microcoin Micromate User Manual ALARM BACKLIGHT CATEGORY No CHECKSUM EXCESS CREDIT AVERAGE COIN SIGNATURE COMMS CONFIG DISCRIMINATION DISPLAY ENABLE GATE OUTPUT LINE 7 0 Glossary QL has an alarm output can be configured to pulse in the event of various conditions The Micromate can switch this output during diagnostic testing to ensure correct operation Refer Micromate Diagnostics The Micromate has a display which can be turned On Off Refer Micromate diagnostics QL has 12 Coin Categories or Coin Channels which can be programmed for individual coins or tokens Each of the 12 C
25. w deliberate presses on the individual keys Listen for the confirmation beep QL Configuration Data Configuration data is downloaded from QL into the Micromate where it is edited Any changes made to the configuration are not saved until the end of the editing session Immediately prior to returning to the Main Menu you will be asked Save Changes to the Validator Y N Pressing NO at this point will leave the existing QL Config unchanged Pressing YES will save your changes by returning the modified Config to QL Coins and Tokens Throughout this manual the term coin is used to cover both coins and tokens Micromate Display This manual shows Micromate screen text as BOLD Capitals Flashing text is shown as NORMAL Capitals Page 2 Version 1 0 April 2001 Microcoin Micromate User Manual 1 0 Connection and Configuration of the Micromate 1 1 Connecting the Micromate RJ11 Cable Connector 2 1mm DC Power Socket for link to Validator Connect to 9V 300mA 3 5mm Stereo Plug NAMA Connector for PC connection Not enabled Not enabled Micromate Off j Power Switcr On The Micromate is normally connected to QL via the supplied RJ11 cable The validator also needs to be connected 12Vdc via its parallel output connector Where power is available it is recommended that the Micromate be powered by a 9Vdc 300mA plug pack to preserve the internal battery Page 3 Version 1 0 April 2001 Microcoin Micromate

Microcoin

Contents

Download Pdf Manuals

Related Search

Related Contents