Home
"user manual"
Contents
1. 15 Set single zone delay time successfully Note This function will only affect the detectors assigned to the Single Delay Zone Zone B To learn how to assign a detector to a Single Delay Zone please refer to the paragraph Zone Setup of Wireless Accessories of this User Manual page 16 Change system language Send 0033 to set the language system as French R glage de la langue fran ais r ussi Send 0001 to set the language system as English Set English successfully Delete Wireless Accessories by SMS Send Delete wireless accessories successfully Delete RFID Tags by SMS Send Delete RFID tags successfully Press the Tamper Switch at the back of the control panel 3 times in 3 seconds both wireless accessories and RFID tags will be deleted Two beeps indicate that the accessories and RFID tags have been deleted Restore System to Default Settings by SMS Send System has been restored to factory settings Press the Tamper Switch at the back of the control panel 5 times in 3 seconds the system will be restored to factory settings Two beeps indicate that the system has been restored to factory settings Only stored numbers can send SMS to restore the system 13 14 Arm amp Disarm by Phone Call Arm Call the control panel number and hang up when you hear the ring tone the system is armed Disarm Call the control panel
2. in electrical and electronic equipment ROHS Directive ROHS and is deemed to comply with the maximum concentration values set by the European Technical Adaptation Committee TAC Manufactured in China nS ue Images illustrations and text are non contractual ETIGER and the ETIGER logo are registered trademarks and the property of ETIGER Copyright 2014 ETIGER All rights reserved ETIGER EUROPE Rue de la Loi 25 7100 La Louvi re Belgium service etiger com 21 3 S UM 20140328 1 2 C eticeR Wild instinct of Technology www etiger com
3. audio monitoring of the site starts Alarm System Specifications Product name S3 Sim Secual Model S3 S Control panel s power supply Input AC 110 240V 50 60 Hz Output DC 12V 500 mA GSM working frequency 850 900 1800 1900 mHz Standby current 110ma Alarm current 340mA Internal battery backup Lithium Battery 3 7V 800 mAh x 2 BL 5B Internal siren 110dB Wireless accessories supported 10x Remote Controls 50x Wireless Accessories and 50x RFID Tags Radio frequency 315MHz 433MHz 75KHz Housing material ABS plastic Operating condition Temperature 10 C 55 C Humidity lt 80 non condensing Control panel dimensions L x W x H 188 x 132 x 26mm Wireless Remote Control Press the Arm button to arm the alarm system The LED indicator lights up the siren rings out once The system is armed If an intruder is detected the siren rings out The siren turns off after 5 minutes as per default setting In the meantime the system dials the pre stored phone numbers automatically Disarm the system Press the Disarm button to disarm the alarm system The LED indicator turns off the siren rings out twice The system is disarmed 15 16 Home Mode Press the Home Mode button on the remote control The system state LED is on All the sensors in regular zones are armed except those in the Home Mode zone The sensors in the Home Mode zone are disarmed so th
4. control chip with intelligent analysis This technology identifies interferences created by body motion and reduces the false alarm rate With automatic temperature compensation and anti air turbulence technology it easily adapts to environmental changes 1 LED indicator 2 Detection window 3 Bracket 18 LED indications Blinks continuously self testing Blinks once an intruder is detected Blinks twice self testing is complete entering working mode Blinks once every 3 seconds under voltage indication the batteries must be replaced The user will be informed by SMS when the batteries are low if the PIR Motion Detector is registered in the control panel PCB Layout Alarm zone setup Tamper switch Antenna Infrared sensor AA 1 5V LR6 Infrared sensor Detects the infrared rays released by human body motion Do not touch the surface Keep the surface clean Tamper switch When the alarm system is armed the tamper switch will trigger the alarm if the case is opened Usage Open the case and remove the battery activation strip to activate the batteries Self testing will start for one minute Mode Setting Test Button Testing mode Once the self testing is complete press the test button The sensor switches to testing mode and scans once every 10 seconds After 3 minutes the LED blinks twice and the sensor switches to working mode Working mode In working mode if the senso
5. number and hold on until the panel ends the call the system is disarmed Register Wireless Accessories amp RFID Tags Type your 4 digit password Press the Connect Button on the control panel the LED indicator lights up Trigger the accessory for the RFID tag swipe it in front of the blue circle of the control panel once within 15 seconds You hear one beep the registration is successful Default password is 1234 If the accesory has already been registered the control panel will beep twice The first accessory registered is assigned to zone 1 the second accessory registered is assigned to zone 2 etc Zones 1 to 9 can be renamed Zone 10 to 50 cannot be renamed Register Wireless Siren Operation Press the Connect Button of the wireless siren The Connect Button LED indicator lights on Press the Arm button on the control panel The panel beeps once the siren is registered Testing Press the Arm Button on the remote control to make sure that the internal siren and wireless siren both beep once If so they are registered If not the registration has failed register them again If an intruder is detected both the internal siren and the wireless siren will ring out The siren will turn off after 5 minutes as per default setting Important When the alarm is triggered the alarm system sends an SMS and calls the stored numbers If one of the users answers the call the siren stops immediately and
6. C ericerR Wild instinct of Technology S3 Sim Secual Alarm system with GSM transmitter www etiger com Features ARM CPU Auror CPU GSM frequency 850 900 1800 1900 MHz suits all phones Supports up to 10 remote controls 50 wireless accessories and 50 RFID tags Radio frequency security of the accessories more than one million code combinations Built in siren 110dB and call function from the panel Arm disarm the system by SMS phone call or application on iOS or Android Stores up to 5 phone numbers 1 speed dial phone number and 1 SMS number for RFID tag notifications Grid failure SMS alert Accessory low battery SMS alert Built in 800 mAh lithium batteries 5h battery life in standby mode Control Panel Layout Front GSM Signal Indicator Searching GSM network Blinks once every second GSM signal is normal Blinks once every two seconds Status Indicator Touch Keypad Arm Disarm Call Stay Arm Home Mode RFID player Play Voice Memo Record Voice Memo Connect Button Control Panel Layout Back MIC Siren Speaker Tamper Switch Loudspeaker Back up Batteries Box Content S3 Panel x1 AC Adapter x1 PIR Motion Detector x2 Door Window Contact Detector x2 Remote Control x2 RFID tag x2 Documentation x1 Record Play Voice Memo Long press the Record Voice Memo button to record a 10 second voice message The voice message can also be recorded by sending an SM
7. S to the system as explained in page 7 of this manual The Play Voice Memo Button blinks when a message has been recorded Touch the centrer of the circle on the control panel to listen to the voice memo The LED indicator turns off when the voice memo is being played Touch it again to replay the memo SIM Card Slot Power On Off Input for Wired Sensors 24 hour zone Input for Wired Sensors normal zone Output for Electronic Lock Output for Wired Siren 500mA Adapter Interface RFID Tag The RFID tag can disarm the system and unlock the electronic door if connected to a wireless keyboard You can rename RFID tags and store a mobile phone number that will receive an SMS notification when the system is disarmed with a RFID tag Note To start receiving an SMS notification when an gt the system is disarmed by RFID tag you must store an SMS number and rename the RFID Mom tags up to 4 RFID tags can be renamed Administrator Speed Dial Press the Call Button the panel auto dials the pre stored phone number Press the Call Button F to end the call The LED turns off after the call Phone Call Dial a phone number and press the Call Button to start the call Press the Call Button to finish the call Electronic Lock When you disarm the system the output signal of the panel opens the electronic lock automatically SMS Operations Request the Menu Send Important Insert a SIM
8. at users can move inside their home Mute Mode Press the Stay button on the remote control Press the Arm button or the Disarm button When arming or disarming the system the siren does not ring out the system is armed or disarmed in Mute Mode Emergency Mode Regardless the status of the system the alarm is triggered when the Panic button SOS is pressed on the remote control Zone Setup of Wireless Accessories Every detector can be assigned to 4 different categories of zones Home Mode Zone Single Delay Zone Normal Zone and 24 H Zone To assign a detector to a zone open its case and move its jumpers according to the drawing below DO me D3 D3 A Home Mode Zone B Single Delay Zone DO C Normal Zone D3 The PIR motion detector is set in Home Mode Zone by default It is recommended to set the Door Window Contact at the entrance of your home in Single Delay Zone After a zone has been changed the detector must be registered in the control panel again 24 H Zone Note It is recommended to set the smoke detector the gas detector and the outdoor beam sensor at 24 H zone Wireless Door Window Contact Features The ES D3A is a Door Window Contact that can be installed on doors windows and any other objects that open and close The sensor sends signals to the control panel when the magnet installed next to the sensor is deconnected Thanks to the tamper swit
9. card in the control panel before starting SMS operations Make sure the SIM card does not request any PIN code The system sends the first part of the menu 0 Disarm 1 Arm 2 Home mode 3 Two way talk 4 Call back voice memo 00 Settings inquiry Store phone and SMS No Each SMS operation included in this user manual will be illustrated as follows Send You send The first blue speech bubble is the SMS The system sends the second part of the command sent by the user menu The control panel replies 5 Store phone No 6 Store alarm SMS No 7 Store SMS No for RFID tags 8 Store speed dial phone No 22 System setups Control panel s reply The first grey speech bubble is the reply sent by the control panel The speech bubbles that follow are the dialogue between the user and the control panel SMS sent by the user are in blue SMS sent by the control panel are in grey The system is in English as per default setting To change the system s language refer to page 13 Send Home Mode Call Back to Record a Voice Memo Store Phone Numbers Send Send Send The system sends the third part of the menu ae The system will call you back Pick up the phone and leave a 10 second message The call end automatically after 10 seconds a Settings Enquiry Two Way Talk D Disarm the System Send Send Copy Paste then Edit
10. case sensitive Send TEL 1 67890033 2 67890022 3 67890011 4 67890000 5 The system will call you back Pick up the phone and start the two way talk Arm the System Note Send The value of default settings will be changed after having set up the system Store Alert SMS Number Send SMS Mal get Rel i Copy Paste then Edit case sensitive SMS 1 67890033 2 67890022 3 67890011 4 67890000 5 Store alarm SMS No successfully Store SMS No for RFID Tags Notifications Send SMS No for RFID tags 0 20 digits 1 Copy Paste then Edit case sensitive SMS No for RFID tags 0 20 digits 1 67890033 Store SMS No for RFID tags successfully Note To start receiving an SMS notification when the system is diarmed by RFID tag you must store an SMS number and rename the RFID tags up to 4 RFID tags can be renamed Other tags will be attributed a number based on the order of registration to the control panel Refer to the instructions page 14 to learn how to register an RFID tag in the control panel Store Speed Dial Phone Number Send Speed dial phone number 0 20 digits 1 Copy Paste then Edit case sensitive Speed dial phone number 0 20 digits 1 67890033 Store speed dial phone number successfully Change Zone Name Send 91 99 For example for zone 1 send Zone 1 name Zone 1 alarm Copy Paste then Edi
11. ch any attenpt to move the Door Window Contact will trigger the alarm Magnet Transmitter LED indicator LED indications Blinks once the door or window is open and the transmitter sends a signal to the control panel Blinks quickly Low power indication the batteries must be replaced PCB Layout Tamper switch A23 12V Battery Zone setting LED working indicator Installation Open the case and remove the battery activation strip Mount the sensor on the door and the magnet on the door frame Make sure the magnet is placed above of the transmitter Mount the magnet max 1cm away from the transmitter and secure the transmitter and magnet with double sided tape or screws Avoid mounting the sensor in areas with a large amount of metal or electrical wiring such as a furnace or utility room Specifications Power supply DC 12V A23 12V Battery x 1 Static current lt 30 uA Alarm current lt 40 mA Transmitting distance lt 80 m in open area Radio frequency 315 MHz 433 MHz 75 KHz 17 Housing material ABS plastic Operating temperature 10 C 55 C Relative humidity lt 80 non condensing Transmitter dimensions LxWxH 71 x34x 17 5 mm Magnet dimensions LxWxH SIX 2X SMM Wireless PIR Motion Detector Features ES D1A or ES D2A Pet Immune Motion Detector is a high performance wireless PI R motion detector It boasts a digital dual core fuzzy logic infrared
12. king B The LED indicator blinks once when body movement is detected C Adjust the detector angle to achieve the best detection performance 20 Detection Scope 110 Top view Specifications Power supply DC 3V AA 1 5V LR6 Batteries x 2 Static current lt 50uA Alarm current lt 9 5 mA Detection scope 8m 110 Trating distance lt 80m in open area Radio frequency 315 MHz 433 MHz 75 KHz Housing material ABS plastic Operating Condition Temparature 10 C 55 C Relative humidity lt 80 non condensing Detector dimensions L x W x H 108 x 52 x 36 8 mm Bracket dimensions L x W x H 52 x 30x 26 5 mm Standards ne This product bears the selective sorting symbol for waste electrical and electronic equipment WEEE This means that this product must be handled pursuant to European Directive 2002 96 EC in order to be recycled or dismantled to minimize its impact on the environment For further information please contact your local or regional authorities Electronic products not included in the selective sorting process are potentially dangerous for the environment and human health due to the presence of hazardous substances CE In compliance with European laws COMPLIANT This product was designed and manufactured in compliance with Directive 2002 95 EC of the European Parliament and of the Council on the restriction of use of certain hazardous substance S
13. r is triggered more than twice within 3 minutes it will switch to standby mode to save power If a movement is detected within the next 3 minutes the standby mode is extended by 3 more minutes If no movement has detected within these 3 minutes the detectors turns back to working mode Register in the control panel Press the Connect button on the control panel Press the test button of the sensor twice The control panel beeps once the motion detector is registered To check if the registration is complete arm the system and trigger the sensor again If the siren rings out the registration is successful Installation Avoid mounting the detector close to windows air conditioner heater refrigerator oven sunshine and places where the temperature changes fast or where the air stream flows frequently If two detectors are installed in the same detection scope adjust the location to avoid interferences and false alarms Top o Ground B ottom Side view l Fix the bracket on the wall with screws and attach the detector to the bracket Adjust the bracket to change the detection distance and angle It is recommended to mount the detector 2m from the ground O Top view The detector is more sensitive to cross movements than vertical movements Testing A After one minute of self testing press the test button walk in the scope of detection and watch the LED indicator to make sure the detector is wor
14. t case sensitive Zone 1 name Entrance door sensor Change zone name seccessfully Note The user can rename zones 1 to 9 The name of the zone cannot consist of more than 30 English characters per line due to SMS character limit Zone 10 to 50 cannot be renamed 10 SMS Alert for Accessory Low Battery available for two way acessories such as Motion Detectors For accessories assigned to zones that have been renamed an SMS will be sent under the format Zone name low battery Bedroom PIR low battery For accessories assigned to zones that have not been renamed an SMS will be sent under the format Zone number low battery Zone 10 low battery SMS Alert for Accessory Tamper Alarm available for two way acessories such as Motion Detectors For accessories assigned to zones that have been renamed an SMS will be sent under the format Zone name tamper alarm Bedroom PIR tamper alarm For accessories assigned to zones that have not been renamed an SMS will be sent under the format Zone number tamper alarm Zone 10 tamper alarm Rename RFID Tag for SMS Notice Send Change RFID Tag SMS Notice ile 2 Be 4 Copy Paste then Edit case sensitive Change RFID Tag SMS Notice 1 Tom 2 Nurse 3 Nancy 4 David Change RFID Tag SMS Notice successfully Note To start receiving an SMS notification when the system is diarmed by RFID tag you m
15. ust store an SMS number and rename the RFID tags up to 4 RFID tags can be renamed Other tags will be attributed a number based on the order of registration to the control panel Refer to the instructions page 14 to learn how to register an RFID tag in the control panel Entry and Exit Delay Time Send Entry and exit delay time 0 300 sec 0 Copy Paste then Edit case sensitive Entry and exit delay time 0 300 sec 610 Set delay time successfully Note This function can be used if you do not want to bring a remote control or RFID tag with you When the system is being armed one beep will be heard every second to remind you to leave The beep rhythm will speed up during the last 15 seconds If an intruder is detected the alarm will be delayed accordingly Siren Volume and Ringing Time Siren volume 0 Mute 1 Low 2 High 2 Siren ringing time 1 9min 5 Copy Paste then Edit case sensitive Siren volume 0 Mute 1 Low 2 High 2 Siren ringing time 1 9min 5 Set siren volume and ringing time successfully 11 12 Disarm Password Send Disarm password 4 6 digits 1234 Copy Paste then Edit case sensitive Disarm password 4 6 digits 8888 Set disarm password successfully Single Zone Delay Time Send Single zone delay time 0 300 sec 30 Copy Paste then Edit case sensitive Single zone delay time 0 300 sec
Download Pdf Manuals
Related Search
Related Contents
Hitachi 32LD9700C Flat Panel Television User Manual Scarica manuale DuPont WFPF38001C Use and Care Manual Carnets 3 Manual - Porter & Charles FICHA DE DATOS DE SEGURIDAD (REACH Philips 6000 series 50PUK6400 50" 4K Ultra HD Smart TV Wi-Fi Black imagina, cria e constrói Sistema de áudio para automóvel de USB/SDHC e Copyright © All rights reserved.
Failed to retrieve file