User Manual - Comkit Online
Contents
1. Requires 200mm space above top panel EEE 222222 TOTO SKOPE VF Series Shelves The freezer is supplied with five wire shelves which may be positioned at different heights to suit various products Always ensure that the shelf clips are securely engaged in each of the shelf support strips Support strips are marked for easy location of shelf clips To fit the wire shelves 1 Unpack the shelves and shelf clips from inside the cabinet 2 Establish the desired position for the shelves and securely engage a shelf clip in each of the shelf support strips 3 Sitthe shelves on the shelf clips 4 The ticket strips clip into place on the front of each shelf Optional Door Lock Cabinets fitted with optional door locks have a key barrel type lock at the top each door Use the supplied keys to lock and unlock the door as necessary Installation User Manual SKOPE VF Series 2 Operation Automatic Start Up After the cabinet has been positioned in a suitable place plug it in and check the following activity Item Activity The condenser fan starts and runs at a slow speed When the Condenser Fan compressor starts the condenser fan will run at full speed The lights that illuminate cabinet interior and top sign where applicable will come on when the freezer is turned on The light s can be switched on and off via the electronic controller ng see over page Cabinets fitted with solid doors u2. 1 x side light 22 Watt T8 LED tube 026mm x 1500mm VF1000 1 x centre pillar light Twin 22 Watt T8 LED tube 26mm x 1500mm To replace the cabinet interior side light model VF650 1 Disconnect the freezer from the power supply 2 Remove the diffuser by squeezing it until it is released from the aluminium housing and then push the diffuser out of the way 3 Rotate the LED tube until the pins on the ends of the tube align with the slots then slide it out 4 Fita new LED tube Ensure the LED tube is fitted with the power end at the top 5 Refit the diffuser by slipping the back section into the housing then squeezing and snapping the front section of the diffuser into place as you work down the length of the light To replace the cabinet interior centre pillar light model VF1000 1 Disconnect the freezer from the power supply 2 Rotate the LED tube until the pins on the ends of the tube align with the slots then slide it out 3 Fita new LED tube Ensure the LED tube is fitted with the power end at the top Servicing 13 User Manual SKOPE VF Series Sign Light Not as standard lit sign freezers only The sign unit is lit by one LED tube 14 see table below for details which can be replaced by removing the front sign panel Sign light specifications Model LED Tube Specification VF650 1 x 9 Watt T8 LED tube O26 x 600mm VF1000 1 x 12 Watt T8 LED tube G26 x 900mm
3. To replace the sign light 1 Disconnect the chiller from the mains power supply 2 Remove the sign assembly Lift the assembly up and off the sign sides and unplug it from the cabinet 3 Seperate the light sign light assembly from the sign panel by undoing the two fixing screws on each side of the sign panel 4 Remove the top of the sign light assembly by undoing the four fixing screws on the top of the sign light assembly A 5 Remove the plastic sign panel and artwork if present from the sign light assembly 6 Rotate and remove the failed LED tube 7 Fitthe new LED tube 8 Refitthe clear front panel and artwork if present and screw the sign top cover back onto the top of the sign assembly 9 Refit and fix the sign light back onto the sign panel assembly 10 Plug the sign assembly back into the cabinet and slot the assembly back onto the sign sides Servicing User Manual Servicing User Manual Troubleshooting SKOPE VF Series For questions about the electronic controller see page 11 For problems with the cabinet and refrigeration cassette use the following table Problem e Cabinet not e Loss of power operating supply e No controller display e Interior light not on Failed LED tube e Blown cabinet fuse e Power consumption Unit operating too is higher than hot expected e Cabinet doors are opened excessively e Product is too warm Restricted airflow to c
4. by placing objects up against the refrigeration cassette Do not probe any opening Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance o Only use this appliance with the voltage specified on the cabinet rating label affixed to the refrigeration cassette o Ensure the appliance has adequate ventilation as this is essential to economical high performance Be careful not to touch moving parts and hot surfaces For your own safety and that of others ensure that all electrical work is done by authorised personnel o lf the power supply flexible cord becomes damaged it must be replaced by an authorised service agent or similarly qualified person in order to avoid a hazard o Ensure all necessary safety precautions are observed during installation or removal of the refrigeration unit o This appliance is not designed to be stable while in motion Use extreme caution when moving or transporting the appliance WARNING Always isolate the freezer from the mains power supply before attempting any maintenance CAUTION Never overload the power supply which could damage the freezer and product See the rating label inside the cabinet for the safe power supply and current draw A Installation User Manual Power Cord Freezer Location Ventilation Installation User Manual SKOPE VF Series Positioning the Cabinet The freezer has a flexible power cord fitted with a
5. 3 pin plug which exits from the top rear of the cabinet Pull the power cord around so that it s not trapped before you position the cabinet The location of the freezer may be the single most important decision that will extend its life and ensure economical high performance We recommend that you put the freezer in the coolest place possible because it will use less power and last longer Although the freezer operates in environs up to 40 C 104 F we suggest that you not constantly run it at the upper end Avoid direct sunlight warm draughts etc Allow adequate space for doors to open and close properly Self closing doors have internal torsion bars pretensioned at the factory and must be unobstructed Ensure the cabinet sits on a level surface so that the doors shut and correctly seal Level footing also prevents the condensate tray from overflowing See diagram below for ventilation guidelines When positioning the freezer ensure there is at least a 200mm space above the top panel Adequate ventilation around the refrigeration unit is essential for efficient operation The air surrounding the refrigeration unit must not exceed 40 C Keep the ventilation slots at the top of the cabinet clear at all times and never store cardboard cartons or other objects on top of the freezer 35 C to 40 C ambient Requires 400mm space above top panel 25 C to 35 C ambient Requires 300mm space above top panel Less than 25 C ambient
6. 5 Power COMA ima ion a awed ae hae e ed ia 5 Freezer LOCANON reir era od tes be oon 5 VENUIAUON e za are aen a o a B AA an A 5 SCI OS esa india eren dae Dado stos 6 Optional Door Lock naana aaa aaa aaa eee 6 2 Operation Automatic Start Up 0 0 0 00 7 Loading Product suse y ide ise cnet de we tec Be ek oe te me are ow uh 7 Electronic Controller ee 8 WAWOGUCUON amen 4 ba ea Shas aS ees bbe Code eee waved 8 FACIAL sata cos aa edito ace ed B ae ee 8 BE abana cents testa es a eenen ten bea oe 9 Continuous Cycle 0 0 ees 9 Temperature Setpoint naaa aaa cee eee 9 Controller Reset ee 10 EEE 11 3 Servicing CICANING 22S omen vanen went etn benk bas os sds 12 Cabinet sro coe en ee be er rd eed EE Dee ee 12 Condenser Coil eee 12 OMG ze tect sae space do aa a kB toba B ea 13 Interior Light anaana 0 eee 13 Sgn GION sacos chews ote oases Bee es Rn Sed oe eae Ss 14 Troubleshooting 5 corra duets ce new a de ieai tii ae aa ans 15 SKOPE VF Series 1 Installation Safety First Always observe safety precautions when using any electrical appliance Read these instructions carefully and retain them for future reference o When the appliance is used by or near young children or infirm persons close supervision is necessary especially to ensure children do not play with it Do not use this appliance for other than its intended use Do not cover the grilles or block the entry or exhaust of airflow
7. CONTINUOUS CYCLE On when freezer is running in continuous run mode Operation User Manual Defrost Continuous Cycle SKOPE VF Series To ensure efficient operation the electronic controller forces a defrost cycle when required During a defrost cycle the compressor stops DEF and the 2 will display on the electronic controller faceplate The freezer will resume normal operation once the defrost cycle has finished A manual defrost can also be initiated by pressing and holding the F button The continuous cycle can be used to pull down the temperature of product inside the freezer quickly During a continuous cool down the compressor runs continuously for a set time To start a continuous cycle 1 While the freezer is switched on and running press and hold the and y buttons for five seconds The amp symbol will display during a continuous cycle To stop a continuous cycle 1 The electronic controller will automatically stop the continuous cycle after a period of time The continuous cycle can be stopped by pressing and holding the A and e y buttons for five seconds Temperature The freezer temperature setpoint is factory set at 21 C If necessary the Setpoint standard setting can be adjusted between 26 C and 16 C Operation User Manual SKOPE do not recommend that the setpoint be changed unless it is absolutely necessary and then only by small increments at a time To view and adj
8. SKOPE VF Series 3 Servicing Cleaning Cabinet Periodically wipe the inside and outside of the cabinet with a damp cloth taking care to keep moisture away from electrical parts As with any maintenance ensure the cabinet is disconnected from the power supply before cleaning Condenser To ensure trouble free performance we strongly urge monthly cleaning with Coil a soft brush to remove dust and fluff A more thorough cleaning is recommended every six months by qualified service personnel The condenser coil must be kept clean for efficient and reliable operation WARNING Disconnect the freezer from the power supply before cleaning the condenser coil To clean the condenser coil 1 Disconnect the freezer from the power supply 2 Remove the sign assembly Lift the assembly up and off the sign sides and if necessary unplug it from the cabinet 3 Clean the condenser coil with a soft brush 4 Refit the sign assembly and reconnect the freezer to the power supply Servicing User Manual 12 SKOPE VF Series Lighting This freezer is designed for use with LED tubes and is not compatible with fluorescent tubes IMPORTANT DO NOT use fluorescent tubes Interior Light The cabinet interior is lit by one side light or one centre pillar light see table below for details which can be replaced without moving shelves or removing product Interior light specifications Model LED Tube Specification VF650
9. VF Series SKOPE Glass Door Vertical Freezer EEDE i iad ww Ga User Manual MAN10521 Rev 1 0 May 2012 KAOT 66A AAAA LLL AAA SKOPE Refrigeration VF Series SKOPE Glass Door Vertical Freezer User Manual MAN10521 Rev 1 0 May 2012 O 2012 SKOPE Industries Limited All rights reserved SKOPE Industries Limited reserve the right to alter specifications without notice SEKO EE is a registered trademark of SKOPE Industries Limited SKOPE INDUSTRIES LIMITED Head Office PO Box 1091 Christchurch New Zealand Freephone 0800 947 5673 Fax 03 983 3896 E mail enquiry skope co nz Website www skope co nz Trademark Infringement The SKOPE trademark on this product is infringed if the owner for the time being does any of the following e Applies the trade mark to the product after their state condition get up or packaging has been altered in any manner e Alters removes including part removal or obliterates including part obliteration the trade mark on the product e Applies any other trade mark to the product e Adds to the product any written material that is likely to damage the reputation of the trade mark Notice of the above contractual obligations passes to e Successors or assignees of the buyer e Future owners of the product SKOPE VF Series User Manual CONTENTS 1 Installation Safety First eee 4 Positioning the Cabinet 0 0 0 0 cee on
10. abinet e Warm cabinet e Blocked condenser temperatures e Compressor e Poor ventilation operating for long around refrigeration periods more than 1 unit hour Possible Cause Suggestions e Check mains power supply e Replace LED tube see page 13 e Contact an authorised service agent to replace it e Clean the condenser coil see page 12 e Ensure the cabinet has good ventilation around the refrigeration unit see page 5 e Ensure the cabinet is in a cool spot e Ensure doors are closed more often e Ensure product is not blocking airflow slots e Ensure there is space around individual product pieces e Clean the condenser coil see page 12 e Ensure the cabinet has good ventilation around the refrigeration unit see page 5 15 SKOPE Contacts SKOPE Industries Limited NEW ZEALAND CONTACT Head Office PO Box 1091 Christchurch New Zealand Freephone 0800 947 5673 Fax 03 983 3896 E mail enquiry skope co nz Website www skope co nz AUSTRALIAN CONTACT A B N 73 374 418 306 PO Box 7543 Baulkham Hills B C NSW 2153 Australia Freephone 1800 121 535 Fax 1800 121 533 E mail enquiry skope com au Website www skope com au
11. plays and related alarms Alarms signal unexpected operational changes in the freezer and stop when action is taken to resolve the problem Code Display Alarm Icon Description a Product HIGH FIA A temperature Flashing alarm Flashing l A Flashing ZT Lt A Flashing A Flashing 7 A Flashing NI ZN NI l Gm A Product LOW temperature alarm Door open alarm High ambient alarm High pressure alarm Control probe fault Evaporator probe fault Ambient probe fault Defrost over time limit Real time clock fault Controller E prom error Controller E prom error Start defrost request End defrost request Initial Action 1 Check the cabinet product loading to ensure ventilation slots are not blocked and that product does not overhang the shelves 2 Ensure the cabinet is installed with good refrigeration unit ventilation 3 Check and clean the condenser coil see page 12 Unplug cabinet from the power supply for 1 minute then reconnect to power supply If problems persist contact SKOPE Check door is closed Check ventilation and operating conditions see page 5 Check and clean the condenser coil see page 12 Contact an authorised service agent to replace probe Unplug cabinet from the power supply for 1 minute then reconnect to power supply If problems persist contact an authorised service agent None 11
12. rature and signals temperature alarms lt uses temperature probes to collect data and runs the freezer accordingly The electronic controller is pre programmed and usually requires no initial setup or additional programming SKOPE does not recommend that the settings be changed unless necessary Faceplate Because the electronic controller plays such an important role it s helpful to know the parts of the faceplate you may use No uh Description Prg mute To initiate program sets press for 5 seconds Mutes the audible alarm buzzer UP aux To switch light s on and off To scroll settings UP in program mode Set If pressed for more than 2 seconds displays and or enables changing the temperature setpoint see page 12 DOWN def To scroll settings DOWN in programme mode COMPRESSOR ON when the compressor and condenser fan starts Flashes when activation of the compressor is temporarily delayed FAN Shows when fan is operational DEFROST ON when the defrost is activated Flashes when the activation of the defrost is temporarily delayed due to procedures in progress 8 auX AUX na 9 A ALARM Flashes in the event of alarms 10 11 12 13 14 15 Se ej 2 al 9 y CLOCK On when real time clock is enabled LIGHT On when the cabinet lighting is activated A SERVICE Flashes in the event of malfunctions DISPLAY Shows the cabinet temperature HACCP HACCP n a 5
13. se an automatic light switch to turn the light on and off with door openings An electronic controller runs the freezer and is visible on the Electronic control panel above the door s The electronic controller Controller display panel shows the cabinet temperature The compressor starts about one minute after the lights go on The compressor turns off when the product temperature Compressor reaches around 21 C and turns on again when it reaches about 18 C The evaporator fan will not operate until the evaporator probe senses a temperature of 8 C on the evaporator coil When the evaporator coil is below 8 C the evaporator will run at slow speed or fast speed as required Evaporator Fan Loading Product Let the freezer run for 30 minutes before loading it with product the first time When loading the freezer o Allow adequate air space around each item to ensure even cooling and efficient operation of the freezer Do not exceed a maximum load of 20kg per shelf Remove some product if the shelves are flexing Do not let anything overhang the shelves because this might stop the doors from shutting or even break something a Do not load product above the load limit indicators shown on the cabinet interior sides see image below LOAD LIMIT Operation 7 User Manual SKOPE VF Series Electronic Controller Introduction The electronic controller controls the freezer displays the freezer tempe
14. ust the temperature setpoint 1 To view the setpoint press and hold the Set key for 2 seconds until the setpoint value flashes 2 To adjust the setpoint press either the ax and keys to display the required setpoint value 3 Press the Set key again to memorise the new setpoint value If this is not done within 60 seconds changes will be lost and you will need to repeat the above procedure SKOPE VF Series Controller To delete program modifications and reset the controller to SKOPE default Reset program or when a replacement controller is being fitted a Controller Reset 10 def Press the A or w keys to select Immediately press the Set key to must be performed To reset the controller Disconnect the freezer from the power supply Prg 2 Press and hold the key while mute plugging the freezer into the power supply this may require two people After a few seconds the controller is reset and program mode bn0 is displayed The controller must never be left in program mode bn0 as failure will occur bn1 for SKOPE default program confirm the preferred program If not confirmed within 60 seconds the freezer will remain in program mode bn0 and cause failure If this occurs repeat the above procedure Operation User Manual Operation User Manual SKOPE VF Series Alarms The following table explains messages that the electronic controller dis
Download Pdf Manuals
Related Search