Manual - CF Monitor
Contents
1. sisi 1 x D SUB 9P Connectors female User Controls On front bezel Power On Off push button Brightness Control 2 x hotkeys Mode Status LED On Screen Display control OSD OSM Environmental Considerations Operating Temperature ia EE 5 C to 55 C HUA odiada da 30 to 90 non condensing Storage TOEMIDCRAUUIF OS 2 eegene 20 C to 60 C HUM id 10 to 90 non condensing Compass Safe DistanGe nado 170 cm Standard 100 cm Steering Safety Consideration Even although the test conditions for bridge units provide for a maximum operating temperature of 55 C continuous operation of all electronic components should if possible take place at ambient temperatures of only 25 C This is a necessary prerequisite for long life and low service costs Available Options 17 Bracket Simrad See page 50 Specifications 37 38 Specifications Technical Description TFT Technology 17 0 inch viewable image size a Si TFT Thin Film Transistor Active Matrix PVA Plus Viewing Angle TFT Characteristics PING UMD ura ai ao 1280 x 1024 Pixel Piten CRGB sra 0 264 H x 0 264 V mm Response TIM as 10 ms typical black to white Contrast Ratas o 1500 1 typical HONE Intensidad 280 cd m2 typical Viewable Angles 0oooccccccccccccancanaos 45 Up 55 Down 89 Right Left typical Active Disblay Alea ni 337 92 H x 270 336 V mm Max eet 16 7 millions Dell EE EE 1280 x 1024 O 62. 100 steps CONTRAST Increase decrease contrast level total 100 steps CS Ifthe display is connected to a DVI source adjustment of brightness and contrast is not possible 14 Operation Color temperature Selecting this function will enable the user to modify the warmness of the picture Higher temperature cooler picture Lower temperature warmer picture User can select between 9500K 8000K 6500K and 5000K color temperature measured in Kelvin degrees Press to access the sub menu where the RGB values can be adjusted Use and buttons to adjust these values and MENU to exit Saving is done automatically Frequency and phase some functions not available in DVI mode Selecting this function will enable the user to modify the image horizontal size and fine tune the image quality FREQUENCY Increase decrease the image horizontal size PHASE Fine tune the data sampling position adjust image quality SHARPNESS Increase decrease video image Sharpness level PICTURE TYPE Motion Still Adjustment for best image quality If graphics on screen move a lot select Motion If graphics on screen are mostly still select Still Video adjustment Selecting this function will enable the user to modify the color saturation of the picture tint and sharpness COLOR Increase decrease video color level TINT Increase decrease tint level SHARPNESS Inc
3. Master the Elements www simrad yachting com Manual Simrad Professional Displays English O O O O O 00 00 O O O 0 00 00 0 O 0 0 0 0 0 0 O O O O O 0 0 0 0 0 Oo Oo OD 0 OD Oo Oo OD Oo 0 Oo 0 0 O0 O O O O O O O O O O O O O O O O O O O O O O O O OO O O O O O O Oo 0 O O O O OD 0 0 O O OD O Oo oO 0 E OO O O O O 00 0 0 O O O 0 00 00 0 00 0 00 0 0 0 O O O O 0 O O 0 00 00 0 O O 00 0 O O 0 0 0 0 0 O O O O O O O Oo O O O O Oo O O O O Oo O O 0 0 O 0 O O O O O O O O O O O O O O O O O O O O O 0 0 0 0 O O O O O O O O O O O O O 0 O O O O O O 0 0 O 0 0 O O O O O O 0 0 0 0 0 Oo Oo OD 0 0 0 0 OD 0 0 0 0 0 O0 O O O O O O 0 0 O 0 O 0 OD 0 0 Oo 0 O O Oo 0 Oo 0 OO O O O O O O O 0 0 O 0 O O 0 0 0 O 0 0 0 0 0 0 OO O O O O O O O 0 0 O O O O 0 0 0 O 0 O O 0 0 0 OO O O O O O O 0 O O 0 O O O O 0 O O 0 0 0 Oo 0 0 0 0 O O O O 00 0 0 0 00 0 00 00 0 00 0 0 0 0 0 0 O O O O 00 0 00 00 0 00 0 00 0 0 0 0 0 0 0 90 O O 000 0 0 00 0 0 0 00 0 00 0 00 0 0 0 0 0 O O O O 0 O 0 0 O O 00 0 00 0 00 0 0 00 0 0 0 O O O O 0 O O 0 00 00 0 O O 0 0 00 O 0 0 0 0 0 O O O O O O O O O O O O O O O O O Oo O O O O OO O O O O O O O O O O O O O O O O O O 00 O O 0 0 0 0 O O O O O O O O O O O O 0 O O O 0 00 0 00 0 0 0 O O O O O O 0 0 0 0 O O OD 0 0 O 0 O O 0 0 0 0 0 O O O O O O 0 0 0 0 0 O 0 OD 0 0 O Oo 0 O 0 0 0 OO O O O O O 0 O Oo 0 0 0 O 0 0 0 0 O 0 OD 0 0 0 0 0 O0 O O O O O O 00 0 O 00 0 00 00 0 0 0 0 0 0 0 0 0 O O O O O O O O O O O O 0 O O O Oo 0 O Oo 0 0 O 0 O O O 00 0 00 0 00
4. or 6 50 4 places 11 139 L 130 ei 11 11 e 464 11 11 Drawings 53 Mounting Bracket for 23 Professional Display SIDE VIEW BACK VIEW 989 TOP VIEW 54 Drawings Master the Elements L60 M Im D A9H 8LEZZZOZ 0U 90Q NF enuey SARIdSIG euolssajotd PRIWIS OS UI
5. 27 Trouble shooting Blank page 28 Trouble shooting 5 Spare parts A 44177954 SS 4 pcs of CUSTOM MADE SIMRAD BOLTS M6X30 mm Use a 3mm Allen Wrench tool to fasten the bolts These should only be used to secure the display into a console or similar 4 pcs of CUSTOM MADE SIMRAD Corner Lids Used to cover the CUSTOM MADE SIMRAD BOLTS in each corner of the display Press it into place 4 pcs of CUSTOM MADE SIMRAD mounting nut for the above M6X30 mm bolt For use inside the console 1 pcs of Standard Signal Cable and or DVI cable DSUB 15P Male to DSUB 15P Male Length approx 4m DVI D 24P Male to DVI D 24P Male Length approx 4m E 1 pcs of Standard Power Cable European or US standard Length approx 2m Note Power cables not included in the DC version 20222378 N 1 pcs of User Manual Optional Accessories Ooo Ateno pen Gesoiegen 44177772 10 Bracket Simrad 44177780 E 12 Bracket Simrad 44177798 15 Bracket Simrad 44177087 17 Bracket Simrad 44177806 19 Bracket Simrad 44177814 23 Bracket Simrad 44177988 ON Bracket mounting kit Delivered only with optional bracket amp 4 pcs of RenCol Tristar Knob Male M6x10 mm y 4 pcs of MicroPlastic 6 mm Nylon washer 4 pcs of Bolt with shoulder washer M6x1x20 4 pcs of Flat washer Use a 4 mm Allen Wrench tool to fasten the bolts Spare parts 29 Blank page 30 Spare parts L 6 Specifications All
6. 6 General information 2 Operation SURYA N BETAN 2 1 User controls MENU Used to bring up the On Screen Display OSD menu and also for navigating to the next function Used for navigating up through available options on the menu sub menus Used for decreasing adjusting values in the menu sub menus Used for increasing adjusting values in the menu sub menus Used for navigating down through available options on the menu sub menus ECDIS Calibration Led Only available on ECDIS versions Used to adjust overall brightness of the picture including LED and lights Power LED On Off button Operation 7 DI 8 Operation 2 2 Turning the display on off This display features an Instant ON Delay OFF switch which ensures that the display is not turned off by user accident Power ON To turn the display on press down the power switch The power light indicator will turn green If no RGB signal sync is present NO SYNC message will appear in the display Power OFF To turn the display off press and hold the power switch down for 3 seconds 2 3 Display illumination The image and LED brightness is adjusted by the rotary knob The display features a 100 dimmable image which means it is capable of displaying a completely black image when the dimmer knob is turned fully to the left All visible LED and lights will also dim 2 4 Assignable hotke
7. Increase decrease the horizontal offset HORIZONTAL STRETCH Increase decrease the horizontal stretch VERTICAL CLIPPING Increase decrease the vertical clipping VERTICAL OFFSET Increase decrease the vertical offset VERTICAL STRETCH Increase decrease the vertical stretch S w xl A LS A LN 2 FILL SCREEN Enable full screen expansion for lower resolution image FILL TO ASPECT RATIO Enable full screen expansion for lower resolution image according to aspect ratio ki LETTERBOX Stretches a letterboxed picture to full screen LETTERBOX WITH SUBTITLES Stretches and pans a letterboxed picture to full screen which enables viewing of subtitles in bottom NONLINEAR SCALING MODES Press to access the sub menu HORIZONTAL CLIPPING Increase decrease the horizontal clipping HORIZONTAL OFFSET Increase decrease the horizontal offset HORIZONTAL STRETCH Increase decrease the horizontal stretch VERTICAL CLIPPING Increase decrease the vertical clipping VERTICAL OFFSET Increase decrease the vertical offset VERTICAL STRETCH Increase decrease the vertical stretch Operation 17 Language Number of available languages depend on display models The language selection will affect all text and messages in the OSD menus Video source Selecting this function will enable the user to select the type of input signal to show full ES screen Available inputs are Analog RGB Composite Video S Video and DVI P
8. 3075 H x 0 3075 V mm Response Tie 25 ms typical black to white Contrast de EE 600 1 typical LAGE INLENSICY EE 350 cd m2 typical Viewable Angles sad Up 45 Down 55 Right 70 Left 70 ACUVE DISPlay Alea EE 246 0 H x 184 5 V mm Max ele 262 144 colors 6 bit max RESOIWTION EE 800 x 600 60Hz Recommended Synchronization CN nl een EUREN Digital separate synchronization Composite synchronization Synchronization on green Auto detects VGA gt SVGA interlaced and non interlaced MIE SIGN Al ns Analog RGB 0 7Vp p Input Impedance 75 Ohm Synchronization Range FOMZOM tala 31 5 kHz to 91 1 kHz o E 60 Hz to 85 Hz Supported Signal Inputs Resolutions ROB be DINA Sa aana aa Laa nan tae 640 x 480 to 800 x 600 VIDEO SIN Siri Interlaced NTSC and PAL SECAM video Composite video S Video Power Specifications Power Supply Options ue EEN 24 VDC Model 12 Pro Display DC Bonded 115VAC 60Hz or 230VAC 50Hz Model 12 Pro Display AC Bonded Power Consumption Operating ani di 100 W max 6 3 15 Professional Display Bonded Mechanical Description Eileen EES W 420 16 57 H 330 13 07 D 50 2 07 WEONES tee viaenonwa Tarat 8 kg 17 6 lbs approx w bracket Input Signal Terminal RAIER EEN E e e EE DVI D Input 24 pin Connector RGBA PEL SIINSE dd 15 pin mini D SUB female Input RGB PERSON E 15 pin mini D SUB female Output COMPOSE e e ari Naga Nak a A Na WA donnie A AG AA a BN AN aa aa
9. DVI D Input 24 pin Connector RGBA PEL SIINSE dd 15 pin mini D SUB female Input RGB PERSON E 15 pin mini D SUB female Output COMPOSE e e ari Naga Nak a A Na WA donnie A AG AA a BN AN aa aaa RCA Phono plug S Waeo S ee EE S Video SVHS plug AC Power signal ista Std IEC Inlet Model 12 Pro Display AC Bonded DC PoWer Signal Screw terminal Model 12 Pro Display DC Bonded User Controls On front bezel Power On Off push button Brightness Control 2 x hotkeys Mode Status LED On Screen Display control OSD OSM Environmental Considerations Operating Temperature aia cdas 15 C to 55 C sa IB jag Keli atan NAN TAPA NATE SANGAN NT RA NG PN E Dan 30 to 90 non condensing Storage Temperature so E 20 C to 60 C PUI GICs rae EE 10 to 90 non condensing Compass Sale DISCAN Ce sia n a Standard n a Steering Safety Consideration Even although the test conditions for bridge units provide for a maximum operating temperature of 55 C continuous operation of all electronic components should if possible take place at ambient temperatures of only 25 C This is a necessary prerequisite for long life and low service costs Available Options 12 Bracket Simrad See page 46 Specifications 33 34 Specifications Technical Description TFT Technology 12 1 inch viewable image size Thin Film Transistor TFT a Si TFT Active Matrix TFT Characteristics PIC NUDO anna a a ds 800 x 600 ER OI eng RGB ooo 0
10. Ge isa E Ee Digital separate synchronization Composite synchronization Synchronization on green Auto detects VGA gt SXGA interlaced and non interlaced a aa a Waa A NE D Aa Na aa Kan Ka Analog RGB 0 7V p p Input Impedance 75 Ohm Synchronization Range HORIZON ao a cdta 31 5 kHz to 91 1 kHz NGU KEE 60 Hz to 85 Hz Supported Signal Inputs Resolutions ROD taa da 640 x 480 to 1600 x 1200 BU EE 640 x 480 to 1600 x 1200 VIGO SIN Siria Interlaced NTSC and PAL SECAM video Composite video S Video Power Specifications Power SUDDIY OPDUOAS cari on 24 VDC Model 23 Pro Display DC 115VAC 60Hz or 230VAC 50Hz Model 23 Pro Display AC Beie el ER ann uge ro tersin la sida Operating 100 W max 23 Professional Display DC ECDIS Color calibrated for the Simrad CS68 ECDIS systems 7 Drawings 7 110 Professional Display Bonded FRONT VIEW SIDE VIEW BACK VIEW 303 GRAD GI E D E UR ENENGE NT oni A D El AAA OH BOTTOM VIEW gt ISOMETRIC VIEW 10x45 4 pls PANEL CUTOUT M6 Thread or 6 5 hole Drawings 43 Mounting Bracket for 10 Professional Display 153 BACK VIEW GE View X Normal to this plane scale 1 4 _ _ _ __2 23 e kl 13 VC A 30 64 283 97 345 26 TOP VIEW 44 Drawings 7 212 Professional Display Bonded FRONT VIEW SIDE VIEW BACK VIEW 365 GURAD 613 E E 63 O E BOTTOM VIEW CU
11. satisfactory result This should however be tested in advance before making the decision on how far the unit can be placed from the signal source Tee A General mounting instructions The useful life of the components of all Electronics Units generally decreases with increasing ambient temperature it is therefore advisable to install such units in air conditioned rooms If there are no such facilities these rooms must at least be dry adequately ventilated and kept at a suitable temperature in order to prevent the formation of condensation inside the unit With most Electronic Units cooling takes place via the surface of the casing The cooling must not be impaired by partial covering of the unit or by installation of the unit in a confined cabinet In the area of the wheel house the distance of each electronics unit from the magnetic standard compass or the magnetic steering compass must not be less than the permitted magnetic protection distance This distance is measured from the centre of the magnetic system of the compass to the nearest point on the corresponding unit concerned When selecting the site of a display unit the maximum cable lengths have to be considered The grounding screws of the units must be connected to the body of the ship ground the wire used should have a cross sectional area of at least 6 mm2 Transportation damage even if apparently insignificant at first glance must immediately be examined a
12. the base mounted cable tie clamp Power input DC version Secure the cables check polarity to the screw terminal you may secure the cable further by mounting it to the base mounted cable tie clamp The internal DC power module supports 24 VDC Remote control soocs N The serial remote control connector s features a RS232 RS422 RS485 interface for MA controlling parameters for the internal display controller such as brightness via external software Not available on 10 12 and 15 inch models On 17 inch one connector COM1 is available On ECDIS models 19 and 23 inch two connectors COM1 COM2 are available 24 Installation 3 3 Pin assignments RGB D SUB 15P Connector Female Input and Output vente eege Reserved for monitor ID bit 2 grounded Digital ground Analog ground red Analog ground green Analog ground blue Digital ground Reserved for monitor ID bit O grounded DDC serial data Horizontal sync or composite sync input Vertical sync input DDC serial clock 5V power supply for DDC optional Installation 25 DVI D 24P DVI I 29P connector female 12345678 C1C2 17 18 19 20 21 22 23 24 C3 C4 Pin Number Description T M D S Data2 Digital RED link 1 T M D S Data2 Digital RED link 1 T M D S Data2 4 Shield T M D S Data4 Digital GREEN link 2 T M D S Data4 Digital GREEN link 2 T M D S Data3 Digital BLUE link 2 MOS Da
13. 0 0 0 0 0 0 0 00 0 0 0 0 O O O O O 00 0 0 0 0 00 0 00 0 0 00 0 0 0 0 0 90 O O O O 00 0 0 0 00 0 00 0 00 0 0 0 0 0 0 0 O O O O O 0 0 00 00 0 00 0 0 00 0 0 0 00 0 0 0 O O O O 0 0 00 0 00 0 00 0 00 0 0 00 0 0 0 0 O O O O O O O O O O O O O O OO O O O O O 0 0 OO O O O O O O O O O O O 0 O O O 00 0 O O 0 O 0 0 0 O O O O O O O O O O O O O O O O O O O O O O 0 0 O O O O O O O 0 O O O O 0 00 O 00 0 0 0 0 0 0 0 0 O O O O O O Oo 0 O O O Oo OD 0 0 O Oo O O 0 0 0 O 0 O O O O O O O Oo 0 O 0 O O OD O 0 O O 0 O 0 0 0 0 O0 O O O O O O O 0 O O O O O OD O O O O O O 0 0 0 O O O O O O O O O O O O O O 0 O O O O 0 0 0 0 0 O O OO O O O O O O O 0 O O O O 0 O O O O 0 O Oo Oo 0 0 O O O O O 0 0 00 0 0 0 0 00 0 0 00 0 0 0 0 0 0 0 0 O O 000 00 00 0 00 0 0 00 0 00 0 0 0 0 0 90 O O 00 0 0 0 0 0 0 00 0 00 0 00 0 0 0 0 0 0 0 O O O O 0 0 0 0 0 0 0 0 00 0 00 0 00 0 0 0 0 0 O O O O 0 O O 0 O O 0 00 0 00 0 0 O 0 0 0 0 0 0 O O O O O O O O O O O O OD O O O O 0 O Oo Oo O0 0 0 8 O O O 0 0 0 0 0 00 0 00 0 00 0 0 0 0 0 0 0 0 0 O 0 O 0 0 O 0 0 0 O QO 0 0 O 0 OO OO OF 0 OF O0 OF 0O O A brand by Navico Leader in Marine Electronics MANUAL Professional displays English Document no 20222378 Revision G Date September 2008 The original language for this document is English In the event of any discrepancy between translated versions and the English version of this document the English document will be the official version To the best of our knowledge the content
14. 0Hz Recommended Synchronization Snell Digital separate synchronization Composite synchronization Synchronization on green Auto detects VGA gt SXGA interlaced and non interlaced Video Signal ria Analog RGB 0 7V p p Input Impedance 75 Ohm Synchronization Range HOnZONta baa aa er er liada 31 5 kHz to 91 1 kHz Vertical EE 60 Hz to 85 Hz Supported Signal Inputs Resolutions RGB i iii 640 x 480 to 1280 x 1024 BALA o Kn Be AR 640 x 480 to 1280 x 1024 e meene ak La e GR Tg aa janna KE een Renae canis Interlaced NTSC and PAL SECAM video Composite video S Video Power Specifications Power Supply Options een ann EEN 24 VDC Model 17 Pro Display DC 115VAC 60Hz or 230VAC 50Hz Model 17 Pro Display AC Power Consumption Operating nn 100 W max 6 5 19 Professional Display Bonded Mechanical Description Eileen EES W 490 19 37 H 400 15 77 D 56 2 27 A Lee EEN 13 kg 28 7 lbs approx w bracket Input Signal Terminal NETEP SINAL iaa DVI I Input 24 pin Connector DER en E ee aan ies 15 pin mini D SUB female Input RGB CPC SIG ial E 15 pin mini D SUB female Output COMPOSE VIGO ar e e Be ee e eg RCA Phono plug S Video ee EE S Video SVHS plug AC Power signal viii dia Std IEC Inlet Model 19 Pro Display AC Bonded DC PoWer Signal Screw terminal Model 19 Pro Display DC Bonded Remote Control Only for ECDIS models occocccono 2 x D SUB 9P Connectors female User Controls On front bezel
15. A a a AE A 304 1 H x 228 1 V mm Max e 16 7 millions RESOLUTION EE 1024 x 768 60Hz Recommended Synchronization EEN SIGN Ge er De io ai Digital separate synchronization Composite synchronization Synchronization on green Auto detects VGA gt SXGA interlaced and non interlaced a ese inatatanieteseteniaaataneees Analog RGB 0 7V p p Input Impedance 75 Ohm Synchronization Range HOnZONCA EEN 31 5 kHz to 91 1 kHz uge KEE 60 Hz to 85 Hz Supported Signal Inputs Resolutions RGB NEE 640 x 480 to 1024 x 768 Ale le State Interlaced NTSC and PAL SECAM video Composite video S Video Power Specifications Power Supply Options ue 24 VDC Model 15 Pro Display DC Bonded 115VAC 60Hz or 230VAC 50Hz Model 15 Pro Display AC Bonded Power Consumption Operating seiersen EEN NNN EEN EEN EEN EEN EEN 100 W max 6 4 17 Professional Display Mechanical Description DIMENSIONS EE W 490 19 37 H 380 15 07 D 55 2 27 VU Lee LEE 9 2 kg 20 3 lbs approx w bracket Input Signal Terminal DVI D CPC SIS NA EE a iaa oa DVI D Input 24 pin Connector RGBA PEL SIINSE dd 15 pin mini D SUB female Input RGB PERSON E 15 pin mini D SUB female Output COMPOSE e e ari Naga Nak a A Na WA donnie A AG AA a BN AN aa aaa RCA Phono plug S Waeo S ee EE S Video SVHS plug AC UPOWE SIN ada Std IEC Inlet Model 17 Pro Display AC DE POWer Signal its Screw terminal Model 17 Pro Display DC Remote control Serial control interface
16. Disable the special password key before entering the OSD menu See page 10 for info USER TIMEOUT Adjust the OSD menu timeout period in a step of 5 seconds Max is 50 Seconds 18 Operation HA FREEZE Press to freeze the display area including PIP view 4 ZOOM Press to access the sub menu ZOOM LEVEL Zooms in the display area from center HORIZONTAL PAN Pan the display area horizontally VERTICAL PAN Pan the display area vertically DIRECT ACCESS 1 amp 2 Press to access the sub menu Define the hotkey function or front under hatch buttons to one of these OSD functions Brightness Contrast Zoom Video Source PIP No Function Test Pattern By pressing the assigned hot key the sequence of the selected input video source are Analog RGB1 Analog RGB2 DVI Composite Video S Video CALIBRATE RGB GAIN ae Color Calibration Press to automatically adjust it 2 DISPLAY ORIENTATION Press to access the sub menu 14 Will flip inverse the display area including PIP view Press to choose between Normal Horizontal Inverse Vertical Inverse Inverse LOAD FACTORY DEFAULTS Press to access the sub menu LOAD USER DEFAULT Load your own personal custom settings SAVE USER DEFAULT Save your own personal custom settings LOAD FACTORY DEFAULT Will reset the VGA controller settings to the factory preset Use caution
17. E Zem ABADAL PEZ Uptional holes 46 50 Screwed from backside of panel NOT MARKED BY AN ARROW gt 6 places PANEL CUTOU Metric thread M6 or 06 50 4 places 344 Drawings 49 Mounting Bracket for 17 Professional Display SIDE VIEW BACK VIEW 460 TOP VIEW 50 Drawings 7 5 19 Professional Display Bonded ECDIS FRONT VIEW SIDE VIEW BACK VIEW 490 SILLA D 8080 me O BOTTOM VIEW E x HIEN o HE m 00 E te E PS oc mi E 1 EE ISOMETRIC VIEW Uptional holes 6 50 Screwed from backside of panel lt NOT MARKED BY AN ARROW 6 places PANEL CUTOUT Metric thread M6 or 46 90 4 places Drawings 51 Mounting Bracket for 19 Professional Display SIDE VIEW BACK VIEW 470 52 Drawings 7 6 23 Professional Display AC DC ECDIS FRONT VIEW SIDE VIEW BACK VIEW 619 00080 500 460 0 BOTTOM VIEW ADAN gl ISUMETRIC VIEW 3 2 11 11 A Ee Optional holes 6 50 Screwed from backside of the panel NOT MARKED BY AN ARROW 6 places PANEL CUTOUT QU mM CU Metric thread M6
18. ECDIS isaka eaaa aana a nana a anana n anane 53 Introduction 3 Blank page 4 Introduction 1 General information 1 1 Display types This manual describes the 10 to 23 Simrad professional displays The following type designations are used size productname supply voltage mme 10 Pro display AC bonded 115 230V AC JH 10T06 SYE D1 10 Pro display DC bonded JH 10T06 SYE D2 12 Pro display AC bonded JH 12104 SYE D1 12 Pro display DC bonded JH 12104 SYE D2 15 Pro display AC bonded JH 15T06 SYE D1 15 Pro display DC bonded JH 15T06 SYE D2 17 Pro display AC JH 17T02 SYE A1 19 Pro display AC bonded 19 Pro display DC bonded 19 Pro display DC bonded 19 Pro display DC ECDIS e Identical to 19 IMO Radar display When delivered for the IMO Radar system the monitor will be labeled CF19 on the front 1 2 Display identification The display identification is found as plain text and with a code on the product label located on the back side of the monitor Product name 19 Pro Display DC Bonded LTT NI C Product ID ID 26057109BA023 26057109 BA 023 DU III oss A Sa steering PIN 26057109 Supply 24V DC part no Se www simradyachting com serial number OA NN A LU JH 19703 SYE D2 023 The display could also be identified by the sticker located on the front cover Refer Adding product labels page 23 General information 5 Blank page
19. Having a PIP view simultaneously will not interfere or change the menu structure in any way Frequency and Phase Frequency B O Phase aa Picture Type Motion A o Up Down select modify Operation 11 12 Operation L Mode 2 Function layout in PC MODE Advanced OSD Menu Service menu To be in PC MODE a computer signal must be present in full screen i e Windows or other operating system radar system Having a PIP view simultaneously will not interfere or change the menu structure in any way Brightness and Contrast Brightness 50 Contrast 50 Up Down select modify Mode 3 Function layout in VIDEO MODE Simplified OSD Menu User menu ES To be in VIDEO MODE a video signal must be present in full screen i e from a camera VCR or DVD player Video Adjustment Color Tint Sharpness Picture Type Motion Video Type DVD Up Down select modify Operation 13 Mode 4 Function layout in VIDEO MODE Advanced OSD Menu Service menu CS Note that to be in VIDEO MODE a video signal must be present in full screen i e from a camera VCR or DVD player Brightness and Contrast Brightness Contrast Up Down select modify Brightness and contrast Selecting this function will enable the user to adjust brightness and contrast for the display BRIGHTNESS Increase decrease brightness level total
20. Power On Off push button Brightness Control 2 x hotkeys Mode Status LED On Screen Display control OSD OSM Environmental Considerations Operating EELSTEN E 15 C to 55 C el nelle GE 30 to 90 non condensing Storage TPEMPCrAUUIFOS sa aa a 20 C to 60 C HARI rada 10 to 90 non condensing Compass Safe Distance EEN EEN 170 cm Standard 120 cm Steering Safety Consideration Even although the test conditions for bridge units provide for a maximum operating temperature of 55 C continuous operation of all electronic components should if possible take place at ambient temperatures of only 25 C This is a necessary prerequisite for long life and low service costs Available Options 19 Bracket Simrad See page 52 Specifications 39 40 Specifications Technical Description TFT Technology 19 0 inch viewable image size Active Matrix Thin Film Transistor TFT MVA Premium TM Technology TFT Characteristics PING UMD ura ai as 1280 x 1024 Pixel Piten CRGB seria 0 294 H x 0 294 V mm Response Nu sia ia 15 ms typical black to white Contrast Ratas Ee 600 1 typical HONE Intensiva 250 cd m2 typical Viewable Anales is 85 deg typical Up Down Right Left ee NR Ee EE EE 376 32 H x 301 056 V mm Max eet 16 7 millions Dell EE EE 1280 x 1024 O 60Hz Recommended Synchronization Snell Digital separate synchronization Composite synchronization Synchronization on green Auto de
21. a RCA Phono plug S Waeo S ee EE S Video SVHS plug AC Power signal ista Std IEC Inlet Model 15 Pro Display AC Bonded DC PoWer Signal Screw terminal Model 15 Pro Display DC Bonded User Controls On front bezel Power On Off push button Brightness Control 2 x hotkeys Mode Status LED On Screen Display control OSD OSM Environmental Considerations Operating Temperature aa idas 15 C to 55 C A ANON EO A 30 to 90 non condensing Storage JEE ee a EE E 20 C to 60 C PUI ENE EE 10 to 90 non condensing Compass Safe Distance EEN 130 cm Standard 85 cm Steering Safety Consideration Even although the test conditions for bridge units provide for a maximum operating temperature of 55 C continuous operation of all electronic components should if possible take place at ambient temperatures of only 25 C This is a necessary prerequisite for long life and low service costs Available Options 15 Bracket Simrad See page 48 Specifications 35 36 Specifications Technical Description TFT Technology 15 0 inch viewable image size Thin Film Transistor TFT MVA Technology TFT Characteristics PIXC NUMDE iaa A AAA AA AAA A 1024 x 768 NK Pitch RGB ai 0 297 H x 0 297 V mm Response TG ti as 30 ms typical black to white COMEFASE ROD eege ee e EE 350 1 typical ant TA SI SARA EE 600 cd m2 typical Viewable Angles rs A 60 Left Right 45 Up Down typical Active Display Ar
22. and make sure you don t bend any of the pins inside the signal cable connector To reduce tension of the signal cable secure it to the base mounted cable tie clamp Connect the other end of the cable to the signal output of your computer and fasten it there also DVI In Connect the DVI cable to the DVI connector female on the rear side of the TFT display If possible screw the DVI cable to the DVI connector and make sure you don t bend any of the pins inside the DVI cable connector To reduce tension of the DVI cable secure it to the base mounted cable tie clamp Connect the other end of the cable to the DVI output of your computer and fasten it there also Ce For 17 displays DVI I connector for other models DVI D connector RGB Out MAA This is a cloned signal from the SIGNAL INPUT which can be redirected to another 4 display e anasi nit A NM Connect the signal cable to the D SUB 15P Connector female on the rear side of the TFT display If possible screw the signal cable to the D SUB connector and make sure you don t bend any of the pins inside the signal cable connector To reduce tension of the signal cable secure it to the base mounted cable tie clamp Connect the other end to the signal input on the second display and fasten it there also Power input AC version The internal AC power module supports both 115VAC 60Hz and 230 50Hz power input You may secure the cable further by mounting it to
23. d that it is properly seated installed on the computer Make sure that a supported video mode has been selected on the display or on the video card system If it is impossible to position the image correctly e the image adjustment controls will not move the image far enough then test it again using another graphics card for the PC system This situation can occur with a custom graphics card that is not close to standard timings or if something is in the graphics line that may be affecting the signal such as a signal splitter please note that normally a signal splitter will not have any adverse effect A faulty TFT panel can have black lines pixel errors failed sections flickering or flashing image Incorrect graphics card refresh rate resolution or interlaced mode will probably cause the image to be the wrong size it may scroll flicker badly or possibly even no image is present Sparkling on the display may be a faulty TFT panel signal cable If unit after unit keeps failing consider and investigate whether you are short circuiting the equipment or doing something else seriously wrong Note that this problem will not occur on bonded products For non bonded products do the following Power on the TFT product and set brightness to 100 Turn off any automatic screensavers on PC or similar During minutes the dew will be gone To speed up the process use a fan heater for a reasonable time Do not overheat the TFT product
24. ed full screen Operation 9 10 Operation OSD keycode See the Utilities section page 18 for reference of location The OSD menu is set to RADAR ECDIS mode as default and a special keycode has to be entered before the OSD menu will be accessible This is to prevent accidental entering of the OSD menu which may block vital information from radar charts etc The special keycode is by factory default set to 321 The keycode field will be located in the lower right corner of the screen and looks like this 000 If the OSD menu is set to YACHTING the OSD menu will be accessible without entering any keycode How to access the ADVANCED OSD menu in RADAR ECDIS MODE To access the Advanced OSD Menu you must enter the special keycode 321 to gain access to the OSD MENU Use the increase decrease and up down buttons to enter the code In RADAR ECDIS mode the OSD menu is always in ADVANCED MODE see next page for explanation How to access the ADVANCED OSD menu in YACHTING MODE To access the Advanced OSD Menu you must press and hold the DOWN button while turning power on When picture appears release the DOWN button and press MENU to access the advanced functions 2 7 OSD menu overview Mode 1 Function layout in PC MODE Simplified OSD Menu User menu To be in PC MODE a computer signal must be present in full screen i e Windows or other operating system radar system
25. el Power On Off push button Brightness Control 2 x hotkeys Mode Status LED On Screen Display control OSD OSM Environmental Considerations Operating Re e le ee 15 C to 55 C HUA odiada da 30 to 90 non condensing Storage TEMPE atUrE ege 20 C to 60 C FEI ICV aaa AA eds 10 to 90 non condensing Compass Safe DistaNCe as iriri a N 215 cm Standard 135 cm Steering Safety Consideration Even although the test conditions for bridge units provide for a maximum operating temperature of 55 C continuous operation of all electronic components should if possible take place at ambient temperatures of only 25 C This is a necessary prerequisite for long life and low service costs Available Options 23 Bracket Simrad See page 54 Specifications 41 42 Specifications Technical Description TFT Technology 23 1 inch viewable image size Thin Film Transistor TFT MVA PremiumTM Technology TFT Characteristics PING NU MIDES rra A AAA as 1600 x 1200 NK Pitch CRG BE ai 0 294 H x 0 294 V mm Response TIIME ti Penta Raabe tee 20 ms typical black to white COMEFASE ROD eege ee e EE 500 1 typical ant Intensivo aa 250 cd m2 typical Viewable Angles EEN 85 deg typical Up Down Right Left CR gt 10 Active Ee EE EE 470 4 H x 352 8 V mm MACU sala E AAK A A A BAANG aaa a a aa ee a NA AA A a MAA aga aa Ga 16 7 millions eil ee EE 1600 x 1200 O 60Hz Recommended Synchronization Sy SIGN
26. en AUTO COMP or SVID AUTO automatic detection of Composite or S Video COMP manual select composite video signal only SVID manual select S Video signal only HORIZONTAL POSITION Adjust the position of the PIP window horizontally VERTICAL POSITION Adjust the position of the PIP window vertically ADVANCED SETTINGS Press to access the sub menu BRIGHTNESS Increase decrease the image brightness of the PIP window CONTRAST Increase decrease the image contrast of the PIP window SHARPNESS Increase decrease the image sharpness of the PIP window TINT Increase decrease the tint of the image of the PIP window COLOR Increase decrease the color of the image of the PIP window Rotation Selecting this function will enable the user to rotate the image to either landscape or portrait format Graphic scaling modes Selecting this function will enable the user to configure the graphic scaling of the PC or VIDEO image Scaling methods in PC DVI MODE ONE TO ONE FILL SCREEN FILL TO ASPECT RATIO NOLINEAR SCALING MODES Scaling methods in VIDEO MODE NORMAL LETTERBOX LETTERBOX WITH SUBTITLES NOLINEAR SCALING MODES ONE TO ONE Press to access the sub menu HORIZONTAL PAN Increase decrease the horizontal pan VERTICAL PAN Increase decrease the vertical pan NORMAL Press to access the sub menu HORIZONTAL CLIPPING Increase decrease the horizontal clipping HORIZONTAL OFFSET
27. go back to the previous menu To begin understanding the menu and its usage just follow these steps for a quick start 1 Press the MENU button The OSD menu will show all the available functions you can adjust or control You can move to the next icon by pressing MENU Select options within icon menu by pressing UP or DOWN buttons The selected option will turn yellow Use or buttons to increase decrease values AA D 5 Move the selection left or right by using or buttons The selected option will turn green 6 To confirm the selection press button The OSD menu consists of 4 modes Icon beside function indicates if its available in that mode Mode 1 Available functions in PC MODE Simplified OSD Menu Logo will appear User can adjust the most common functions needed to operate the display Mode 2 Available functions in PC MODE Advanced OSD Menu No logo will appear User can access more advanced functions Service menu Mode 3 Available functions in VIDEO MODE Simplified OSD Menu Logo will appear User can adjust the most common functions needed to operate the display Mode 4 Available functions in VIDEO MODE Advanced OSD Menu No logo will appear User can access more advanced functions Service menu PC MODE When RGB signal i e Windows or other operating system is displayed full screen VIDEO MODE When video signal i e CAMERA VCR DVD is display
28. in this publication was correct at the time of printing As we are continuously improving our products we retain the right to make changes to the product and the documentation at any time Updated manuals are available from our website www simrad yachting com and are free to download Copyright 2008 by Navico Holding AS 2 Introduction Copyright All rights reserved No part of this document may be reproduced or otherwise copied without prior written permission of Navico Holding AS 2007 by Navico Holding AS About this manual This manual holds information for installing and using the Simrad professional displays Important text that requires special attention from the reader is emphasized as follows Used to draw the reader s attention to a comment or some important information Used when it is necessary to warn personnel that a risk of damage to the equipment or injury death exists if care is not exercised Sections The document includes the following sections 1 General information Information about display types and how they are identified 2 Operation Description of keys and OSD menu 3 Installation Mechanical installation cable connection and plug description 4 Trouble shooting List of probable faults and recommended action to fix the problem 5 Spare parts List of standard and optional spare parts for the displays 6 Specifications Mechanical and technical specifications for the various display mode
29. ls 7 Drawings Mechanical drawings and panel cut outs for all display models Content 1 General INFOFMALION ii nen 5 EA DISDIOY LY DSS a A 5 1 2 Display identificat ON siaga aa a AAN a a NAAS KAGAN JA AA 5 Seilen EE 7 ZA USE CON Ul OlS EE 7 22 TURAING TNS display ONO EE 8 273 DISPIAy MUIMUIM ALON csi ia 8 2 4 Assignable eg TEE 8 25 ECDIS Callbration LED EE 8 ZO OS D IMenU id A A AA AA Aa 9 LIL O50 EIERE ENEE eg 11 CR EU E e Vu EEN 21 3 1 Installation recommendations EE 21 312 PAN en Re eieiei d Le Lu EEN 23 2S PANAS SIGIT ia anes E ria ee teers E SE aia 25 4 TLroublesieotpnggexsgetgekkgiugegeg gett A A EEN ege 27 5 Spare parts sasukane a naa aaa iaa 29 le lh d Le de Tu CR NENGENA NENGGE NENEKA 31 6 1 10 Professional Display Bonded cc cece cee saene aana anaa anana anana a nane 31 6 2 12 Professional Display Bonge 33 6 3 15 Professional Display Bonded cccccccccccccoccccrccnnrrnnrrr rr rr 35 6 417 Professional DISDIA Visio aa 37 6 5 19 Professional Display Bonded occcccccccccccccccnccnnr rn rr rr rr 39 66 23 Professional DISPIAY ii 41 7 Drawings OA 43 7 1 10 Professional Display Bonded ae EEN 43 7 2 12 Professional Display Bonded ccccccccccccnocccorccnnrrnnrrr rr rr rr 45 7 3 15 Professional Display Bonded ae EEN rn rr rr rr 47 KALI Oe e te ERT e E EE 49 7 5 19 Professional Display Bonded ECDIS ss s asa cece ee anana aana nana 51 7 6 23 Professional Display AC DC
30. mage size Thin Film Transistor TFT a Si TFT Active Matrix TFT Characteristics PING NUMIDG iaa AAA ARA AA AAA 800 x 600 NK Pitch RGB ai 0 264 H x 0 264 V mm Response TG to das 25 ms typical black to white COMEFASE ROD ridad 700 1 typical ant TA SI SATYA EE 400 cd m2 typical Viewable e iia da Up 85 Down 85 Right 85 Left 85 Active Display AV EE 211 2 H x 158 4 V mm Max lee 262 144 colors 6 bit max RESOLUTION darla 800 x 600 O 60Hz Recommended Synchronization SVNG SIGN Gls er De iodas Digital separate synchronization Composite synchronization Synchronization on green Auto detects VGA gt SVGA interlaced and non interlaced a O O Analog RGB 0 7Vp p Input Impedance 75 Ohm Synchronization Range HORIZON atada dial 31 5 kHz to 91 1 kHz NGU KEE 60 Hz to 85 Hz Supported Signal Inputs Resolutions RGB DVIS aaa 640 x 480 to 800 x 600 video ele EE Interlaced NTSC and PAL SECAM video Composite video S Video Power Specifications Power Supply Options ue EEN 24 VDC Model 10 Pro Display DC Bonded 115VAC 60Hz or 230VAC 50Hz Model 10 Pro Display AC Bonded Power Consumption Operating aieiaiee AN EEN NN NENNEN A EEN EEN EEN 100 W max 6 2 12 Professional Display Bonded Mechanical Description DIMENSIONS 2 ac NG Na a a W 365 14 47 H 259 10 27 D 60 2 47 WEONES NE Pa a Nan 6 kg 13 2 lbs approx w bracket Input Signal Terminal DVI D CPC SIGN ala ME Nn iaa aa
31. me na AEB woo w OQd CH MORA e n een AC LG ENO eg Je e 90999 ISOMETRIC VIEW PANEL CUTOUT M6 Thread or 6 3 hole 4 pls Drawings 45 Mounting Bracket for 12 Professional Display View X Normal to this plane scale 1 4 153 BACK VIEW o ew Ee d Jee ees 30 64 283 97 345 26 TOP VIEW 46 Drawings 7 3 15 Professional Display Bonded FRONT VIEW BACK VIEW SIDE VIEW BOTTOM VIEW TOP VIEW DODOA KA UD ISOMETRIC VIEW ave IST i L 394 Optional holes 6 90 Screwed from backside of panel NOT MARKED BY AN ARROW 6 places g 6 PANEL CUTOUT 4 places Metric thread M6 or We 20 Drawings 47 Mounting Bracket for 15 Professional Display SIDE VIEW BACK VIEW 400 TOP VIEW 48 Drawings 7 4 17 Professional Display FRONT VIEW 490 SIDE VIEW RR BUTTOM VIEW E gt 000000000 e 0000000000 e 0000000000 0000000000 e 0000000000 992000000 cu ae P VIEW 20 450 INN 00000000000000000000000000000000000000000000000000000000000000000000000 P L 454 Se lol e U E Ee ET
32. nd be reported to the freight carrier The moment of setting to work of the equipment is too late not only for reporting the damage but also for the supply of replacements Adding product labels SIMRAD The monitor is delivered with a set of product labeling stickers The sticker that matches the system should be attached to the front of the monitor O FH bla E 3 2 Physical connections The illustration below shows an example on connector layout RGB OUT RGB IN DVI IN REMOTE CONTROL COMPOSITE IN S VIDEO IN POWER INPUT Composite In PAL NTSC SECAM VIDEO Connect your composite video signal cable into the RCA jack plug To activate the Picture In Picture function the TFT display must be configured via the OSD menus Note that Composite Video must be selected as the incoming video source Installation 23 S VIDEO In og 9 Connect your S Video SVHS video signal cable into the mini 4 way din plug It can only be inserted one way and make sure you don t bend any of the pins inside your cable To activate the Picture In Picture function the TFT display must be configured via the OSD menus CS S Video must be selected as the incoming video source RGB In seees Y Connect the signal cable to the D SUB 15P Connector female on the rear side of the TFT mai y display If possible screw the signal cable to the D SUB connector
33. rease decrease video image Sharpness level PICTURE TYPE Motion Still Normal Adjustment for best image quality If graphics on screen move a lot select Motion If graphics on screen are mostly still static select Still If general motion non flicker mode select Normal VIDEO TYPE Change to best match the source signal DVD VCR Video system Selecting this function will enable the user to select video system and input signals AUTO Automatic detection of NTSC or PAL system Not applicable in SECAM NTSC NTSC 4 43 Manual select NTSC system PAL PAL M Manual select PAL system SECAM Manual select SECAM system Status Selecting this function will display graphic information such as resolution and frequency Operation 15 312 EB wl 16 Operation Position no function in DVI mode Selecting this function will enable the user to position the image within the display area IMAGE UP DOWN Position the image vertically using UP or DOWN buttons IMAGE LEFT RIGHT Position the image horizontally using or buttons Picture in picture Selecting this function will enable the user to configure PIP window size input signal source horizontal and vertical position and more PIP SIZE Select PIP window size Scale level from O to 24 If the value is set to O the PIP function is turned OFF PIP SOURCE Select video source to be displayed in PIP window Choose betwe
34. recommend installing the unit in a vertical position 30 degrees to improve the airflow through the unit Exposure to direct sunlight can cause a considerable increase in the temperature of the unit and might under certain circumstances lead to over temperature This point should already be taken into consideration when the bridge equipment is being planned sun shades distance from the windows ventilation etc Space necessary for ventilation for cable inlets for the operating procedures and for maintenance must be provided To further improve the cooling of the unit we recommend installing Cooling Fans underneath blowing upwards into the unit air inlet This may be required in high temperature applications and also when there is reason to expect temperature problems due to non optimal way of mounting If the push buttons of the display are not illuminated an external dimmable illumination IEC 60945 6 5 c e g Goose neck light is required for navigational use Information about necessary pull relievers for cables is given in the installation drawings Attention must be paid to this information so that cable breaks will not occur e g during service work Ergonomics 1 Adjust the unit height so that the top of the screen is at or below eye level Your eyes should look slightly downwards when viewing the middle of the screen Adjust screen inclination to remain gaze angle to the centre of the screen approximately perpendic
35. ressing will activate the input and pressing will detect automatically Utilities Selecting this function will enable the user to configure the OSD menu define hotkeys a and miscellaneous operations USER SETTING Press to access the sub menu IA DPMS Disable Enable the DPMS function DISPLAY INPUT Disable Enable input source name upon power up AUTO SOURCE SELECT Off Disable auto source select function Low Auto source select enabled ONLY in power up High Auto source select ALWAYS enabled GAMMA 1 0 1 6 2 2 Adjusts gamma on TFT display SERIAL ADDRESS Set serial Remote Channel from 0 to 15 This function is only available on 17 and newer revisions of 10 12 15 19 and 23 OSD SETTING Press to access the sub menu OSD H POSITION Position the OSD menu horizontally OSD V POSITION Position the OSD menu vertically OSD BACKGROUND Choose between Opaque default or Translucent OSD MENU ROTATE Choose between Normal Rotate Will position the menu either horizontally or vertically OSD MODE Choose between Normal Toggle Normal Always display the Simplified OSD mode Toggle Display the last saved OSD menu mode OSD LOCK MODE Choose between Radar ECDIS default or Yachting Radar ECDIS Enable the special password key input mode before entering the ADVANCED MENU Note Code is by factory default 321 See page 10 for more info Yachting
36. specifications are subject to change without prior notice 6 1 10 Professional Display Bonded Mechanical Description DIMENSIONS EE W 303 11 95 H 220 8 75 D 58 2 37 VU el he 4 kg 8 8 lbs approx w bracket Input Signal Terminal BER Den SION dt oro DVI D Input 24 pin Connector PB EE Eege 15 pin mini D SUB female Input Deen SIDA KEE 15 pin mini D SUB female Output COMDOSICS VIGO sra RCA Phono plug so ES le lp E S Video SVHS plug AC Ge el EE Std IEC Inlet Model 10 Pro Display AC Bonded DC Power signal ascii Screw terminal Model 10 Pro Display AC Bonded User Controls On front bezel Power On Off push button Brightness Control 2 x hotkeys Mode Status LED On Screen Display control OSD OSM Environmental Considerations Operating o e A 15 C to 455 C a EE 30 to 90 non condensing Storage RR unt tee 20 C to 60 C allari ele EE 10 to 90 non condensing Compass Safe Distance curtido n a Standard n a Steering Safety Consideration Even although the test conditions for bridge units provide for a maximum operating temperature of 55 C continuous operation of all electronic components should if possible take place at ambient temperatures of only 25 C This is a necessary prerequisite for long life and low service costs Available Options 10 Bracket Simrad See page 44 Specifications 31 32 Specifications Technical Description TFT Technology 10 4 inch viewable i
37. tects VGA gt SXGA interlaced and non interlaced Video Signal ria Analog RGB 0 7V p p Input Impedance 75 Ohm Synchronization Range HOnZONta baa aa er er liada 31 5 kHz to 91 1 kHz Vertical EE 60 Hz to 85 Hz Supported Signal Inputs Resolutions RGB i iii 640 x 480 to 1280 x 1024 BALA o Kn Be AR 640 x 480 to 1280 x 1024 e meene ak La e GR Tg aa janna KE een Renae canis Interlaced NTSC and PAL SECAM video Composite video S Video Power Specifications Power Supply Options c 0ccccccccccccccnccnnnnnnnnns 24 VDC Model 19 Pro Display DC Bonded 115VAC 60Hz or 230VAC 50Hz Model 19 Pro Display AC Bonded POWer e ei ER ia ning ee KEE Operating 100 W max 19 Professional Display DC ECDIS Color calibrated for the Simrad CS68 ECDIS system 6 6 23 Professional Display Mechanical Description Eileen EES W 615 19 37 H 500 15 77 D 54 2 17 AA Lee LEE 17 kg 37 5 lbs approx w bracket Input Signal Terminal DVI D CPC SIGN ala ME Nn iaa aa DVI D Input 24 pin Connector RGBA PEL SIINSE dd 15 pin mini D SUB female Input RGB PERSON E 15 pin mini D SUB female Output COMPOSE e e ari Naga Nak a A Na WA donnie A AG AA a BN AN aa aaa RCA Phono plug S Waeo S ee EE S Video SVHS plug AC UPOWE SIN ada Std IEC Inlet Model 23 Pro Display AC DC POW ECE SiN its Screw terminal Model 23 Pro Display DC Remote Control Only for ECDIS models susi sarean 2 x D SUB 9P Connectors female User Controls On front bez
38. tos Seta T M D S Data0 5 Shield T M D S Data5 Digital RED link 2 DDC Display Data Channel T M D S Transition Minimized Differential Signal PIN C1 C2 C3 C4 Only present on DVI I connectors 26 Installation No picture LED behavior Scrolling unstable image Display area is not centered sized correctly Image appearance Continued failure Dew condensation behind glass 4 Trouble shooting If for some reason there should be something wrong with the picture quality or no picture present check the symptoms carefully and try to cure it with the hints below Recommended action Power Switch and computer power switch should be in the ON position The signal cable should be completely connected to the video card computer Check the connector for bent or pushed in pins If the LED in front is red no external VGA signal is present If there is no light at all in the LED try to turn the brightness knob If it s still black no power is present to the unit Check your external power source A lack of image is most likely to be caused by incorrect connection lack of power failure to provide a signal or incorrect graphic card settings Signal cable may not be completely connected to computer or TFT display Check the pin assignments and signal timings of the display and your video card with respect to recommended timing and pin assignments Make sure that the video card is compatible an
39. ular to the line of gaze When screen are to be operated both from a sitting position and from a standing position a screen inclination of about 30 to 40 from a vertical plane has turned out to be favorable Units in the bridge wing area must be installed or mounted by suitable alignment or bulkhead deckhead mounting in such a way that reflections of light from the front pane of the unit are not directed into the observer s viewing direction The use of ordinary commercial filter plates or filter films is not permitted for items of equipment that require approval by optical effects aids of that kind can Suppress small radar targets for example Installation 21 22 Installation Cables Use only high quality shielded signal cables with separate coax for Red Green and Blue video signal If you are using DVI D use only high quality DVI cables Cable entries amp connectors marked area Illustration only Back View Maximum cable length The RGB DVI cable should generally be kept as short as possible to provide a high quality output on the unit The maximum cable length will depend on the signal resolution and frequency but also on the quality of the signal output from the computer We recommend using 60Hz vertical frequency Cables up to 10 meters generally provide good picture quality even with a 1600x1200 UXGA 60Hz signal In most cases especially with lower resolutions even longer cables will provide a
40. when using this function as this will override your current settings Does not affect USER DEFAULTS SETUP DCC Reset optimize image information This function will setup correct DDC Display Data Channel information It allows the display module to send its specifications to the display controller This information is used by the OSD menu Note This function is not available on older models TEST PATTERN Shows a generic test pattern Volume q This function is not implemented and has no operational effect Operation 19 Exit menu Selecting this function will exit the OSD menu Press to exit and save the current settings CS The OSD settings will also automatically be stored in memory when the OSD exit on user timeout 20 Operation 3 Installation 3 1 Installation recommendations Installation and mounting of displays 1 The displays are intended for various methods of installation or mounting panel mounting bracket mounting ceiling wall mounting etc for details please see the relevant mechanical drawings Adequate ventilation is a necessary prerequisite for the life of the display The air inlet and outlet openings must definitely be kept clear coverings which restrict ventilation are not permissible Do not install the unit in a horizontal position laying down as this will cause heat to build up inside the display which will damage the LCD Panel To prevent this problem we
41. ys The user can assign various display functions as hotkeys to the increase decrease keys This will enable the user to quickly adjust the brightness image size contrast or other functions to control the image To assign these hotkeys enter the UTILITIES MENU DIRECT ACCESS menu and change them to the desired hotkey function Default hotkeys are set to increase decrease contrast 2 5 ECDIS Calibration LED The calibrated led indicator is only active for displays which are calibrated for ECDIS Each ECDIS factory prepared display has its individual backlight brightness setpoint where it is in accordance with the ECDIS standard To adjust the backlight brightness to this setpoint turn the brightness knob until the led indicator is on emits green light For verification a small sticker on the back cover are placed over the setpoint adjust hole Do NOT remove the sticker and attempt adjust doing so will make the ECDIS calibration invalid 2 6 OSD menu The On Screen Display OSD menu controls are as default located on the right side of the display In the OSD menu you can select other display locations for the menu The selection will be stored in the display The On Screen Display OSD menu contains several functions that will let the user to adjust or setup the display to their preferred setting The functions are shown as easy understandable icons Some of the menus have sub menus use to access and MENU to
Download Pdf Manuals
Related Search