Home

Expression 33000 Zoom

1. from 0 100 Channel 7 Amber Dimmer must be open A 0 255 Gradual adjustment Blue from 0 100 Channel 8 Macro Colors No Function Full Power Only when menu 4 Special Power Normal has been set to Normal Red 100 Green Up Blue 0 Red Down Green 10076 Blue 076 Red 0 Green 100 Blue Up Red 0 Green Down Blue 100 Red Up Green 076 Blue 10076 Red 100 Green 0 Blue Down Red 100 Green Up Blue Up Red Down Green Down 100 Red 100 Green 100 Blue 100 White 100 White 3200K White 3400K White 4200K White 4900K White 5600K White 5900K White 6500K White 7200K White 8000K White 8500K White 10000K Channel 9 Dimmer intensity 0 255 From black to brightest Channel 10 Shutter Strobe Dimmer must be open A 09 Open 10 255 Strobe effect from slow fo fast 0 10 flashes sec Channel 11 Zoom 0 255 Channel 12 Control 25 DMX Protocol 14 Channels G1 Channel 1 Horizontal movement Pan Push the slider up in order fo move head horizontally PAN Gradual head adjustment from one end of the slider to the other 0 255 128 center The head can be turned by 540 and stopped at any position you wish Channel 2 Pan fine 16 bit Channel 3 Vertical movement Tilt Push the slider up in order to move head vertically TILT Gradual head adjustment from one end of the slider to the other 0 255 128 center The head ca
2. Connection Lockable Volex IEC and 5 pin XLR In and Out e IP rating IP 20 Less heat Forced cooling fan e Fan Speed Control Bright LCD display Control DMX 512 Master Slave Fuse T5A 250V Overview Fig 1 1 Lens 2 Menu Buttons LCD Display Backside Fig 2 3 Earth 4 ON OFF 5 IEC power connector Fuse T5A 250V 6 DMX signal connector IN 3 pin 7 DMX signal connector OUT 3 pin 8 DMX signal connector IN 5 pin 9 DMX signal connector OUT 5 pin Installation Remove all packing materials from the Expression 33000 Check that all toam and plastic padding is removed Connect all cables Do not supply power before the whole system is set up and connected properly Always disconnect from electric mains power supply before cleaning or servicing Damages caused by non observance are not subject to warranty Set Up and Operation Follow the directions below as they pertain to your preferred operation mode Before plugging the unit in always make sure that the power supply matches the product specification voltage Do not attempt to operate a 120V specification product on 230V power or vice versa Fixture Linking You will need a serial data link to run light shows of one or more fixtures Using DMX 512 controller or to run synchronized shows on two or more fixtures set master slave operating mode The combined number of channels required by all the fixtures on a s
3. Expression 33000 Zoom ORDERCODE 41368 SHOWELECTRONICS FOR PROFESSIONALS Congratulations You have bought a great innovative product trom Showtec The Showtec Expression 33000 brings excitement to any venue Whether you want simple plug amp play action or a sophisticated DMX show this product provides the effect you need You can rely on Showtec for more excellent lighting products We design and manufacture professional light equipment for the entertainment industry New products are being launched regularly We work hard to keep you our customer satisfied For more information iwant showtec info You can get some of the best quality best priced products on the market from Showtec So next time turn to Showtec for more great lighting equipment Always get the best with Showtec Thank you Showtec Showtec Expression 33000 Product Guide Warning OS O D TOT vente a ee ie ice OO eran T E Rec So T Features and Overview Backside OVS NETTO Set Up and Operation Fixture Linking Blo 16 e A Meer c rere eat weal nw T senor ot T T
4. 4900K 211 215 White 1 4200K 206 210 White 1 3400K 201 205 White 1 3200K Red 100 Green 100 Blue 100 hite 171 200 151 170 ed Do 131 150 Red 100 Green Up Blue 111 130 Red 100 Green 0 91 110 Red Up Green 0 Blue 100 71 90 Red 0 Green Down Blue 100 51 70 Red 0 Green 100 Blue Up 31 50 Red Down Green 100 Blue 0 11 30 Red 100 Green Up Biue 0 6 10 Full Power 0 5 No Function 2 Maintenance The operator has to make sure that safety relating and machine technical installations are to be inspected by an expert after every year in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are to be inspected by a skilled person once a year he following points have to be considered during the inspection 1 All screws used for installing the device or parts of the device have to be tightly connected and must not be corroded 2 There may not be any deformations on housings fixations and installation spots 3 Mechanically moving parts like axles eyes and others may not show any traces of wearing 4 The electric power supply cables must not show any damages or material fatigue The Showtec Expression 33000 requires almost no maintenance However you should keep the unit clean Otherwise the fixture s light output will be significantly reduced Disconnect the mains power supply and then wipe the cover with a damp cloth Do not imm
5. Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires Before your initial start up please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device To maintain perfect condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Please consider that damages caused by manual modifications to the device are not subject to warranty his device contains no user serviceable parts Refer servicing to qualified technicians only IMPORTANT Ihe manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to The device e Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution e Never remove warning or informative labels from the unit Never use anything to cover the ground contact e Neverrun the device without lamp Never ignite the lamp if the objective lens or any housing cover is open as discharge lamps may expose and emit a high ultraviolet radiation which may cause burns Never lift the fixture by holding it at the projector head as the mechanics may be damaged Always hold the fixture at the transport handles Never place
6. O C 2 L N Q O gt D O zt 2 N o 2 D 3 D 2 C see menu 7 8 and 9 You have enter password UP DOWN UP DOWN in menu EXTRA A When you use the menu button the 3 hidden menus will now appear 1 Intro Menu 15 DMX Addressing With this menu you can set the DMX address EE i 1 Press Menu until the display shows Intro 2 Press Enter and use the Up Down buttons to go to the Address menu 3 Press enter to open this menu You can choose 512 different DMX addresses Use the Up Down buttons to select the required address from 000 512 4 Once you have set the desired DMX address press the enter button to store your DMX address Reset With this menu you can reset the device A 1 Press Menu until the display shows Intro 2 Press Enter and use the Up Down buttons go to the Reset menu 3 Press enter to open this menu You can choose Yes No mode Use the Up Down buttons select one 4 Once you have set Yes the device will reset and will take 15 seconds reset Fans With this menu you able to control the fan speed of the device EE 1 Press Menu until the display shows Intro 2 Press Enter and use the Up Down buttons to go to the Fans menu 3 Press enter to open this menu Use the Up Down buttons set the desired fan speed DMX Active With this menu you able to c
7. 100 Channel 10 Amber Dimmer must be open 0 255 Gradual adjustment Blue from 0 100 Channel 11 Macro Colors Red 0 Green 100 Blue Up Red 100 Green 0 Blue Down 221 225 White 5600K 216 220 White 4900K 226 230 White 5900K Channel 12 Dimmer intensity 0 255 From black to brightest Channel 13 Shutter Strobe Dimmer must be open A Open 10 255 Strobe effect from slow fast 0 10 flashes sec Channel 14 Zoom 0 255 Zoom Channel 15 Control 200 219 Reset activated after 5 seconds 180 199 220 235 23 DMX Protocol 12 Channels Basic Channel 1 Horizontal movement Pan Push the slider up in order fo move head horizontally PAN Gradual head adjustment from one end of the slider to the other 0 255 128 center The head can be turned by 540 and stopped at any position you wish Channel 2 Vertical movement Tilt Push the slider up in order to move head vertically TILT Gradual head adjustment from one end of the slider to the other 0 255 128 center The head can be turned by 270 and stopped at any position you wish Channel 3 Red Dimmer must be open A 0 255 Gradual adjustment Red from 0 100 Channel 4 Green Dimmer must be open A 0 255 Gradual adjustment Green from 0 100 Channel 5 Blue Dimmer must be open N 0 255 Gradual adjustment Blue from 0 100 Channel 6 White Dimmer must be open 0 255 Gradual adjustment
8. 7 UP DOWN ENTER ENTER 1 Press Menu until the display shows Invert 2 Press Enter and use the Up Down buttons scroll through the options Pan Tilt Dimmer Use 3 Press enter to open this menu Use the Up Down buttons to select one of the options 4 Once you have set the desired mode press the enter button store your setting 3 Range ENTER ENTER 7 ENTER UP DOWN ENTER ENTER 1 Press Menu until the display shows Range 2 Press Enter and use the Up Down buttons scroll through P Start P Finish T Start T Finish Use 3 Press enter to open this menu Use the Up Down buttons to set the desired value 4 Once you have set the desired mode press the enter button store your setting 4 Special ENTER ENTER ENTER ENTER ENTER ENTER ENTER UP DOWN 1 Press Menu until the display shows Special 2 Press Enter and use the Up Down buttons to choose BlackDelay Reset Power Color Fan DMX Error 3 Press enter to open this menu Use the Up Down buttons to set the desired setting 4 Once you have set the desired mode press the enter button to store your setting 18 5 Edit ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER UP DOWN 1 Press Menu until the display shows Edit 2 Press Enter and use the Up Down buttons scroll through the options Step Pan Tilt Soeed Red Green Blue
9. White Amber Dimmer Strobe Zoom Time Use 3 Press enter to open this menu Use the Up Down buttons to set the desired setting 4 Once you have set the desired mode press the enter button to store your setting Note If you want to circulate the created steps please set the last step as O For example when you have 3 steps the setting should be Step Time 4 Use Yes Step 2 Time 5 Use Yes Step 3 Time 0 Use Yes 6 Extra Password 6 1 Press Menu until the display shows Extra 2 To see menu 7 8 and 9 you have to enter password Up Down Up Down in menu 6 1 When you use the menu button the 3 hidden menus will now appear he Access Password UP DOWN UP DOWN When you have pressed ENTER in menu KEYLOCK ON it will take 30 seconds before the Expression 33000 is locked When the password is activated the display will ask for password each time the fixture is powered 19 7 Calib ENTER UP DOWN ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER 20 7 Calib 1 Press Menu until the display shows Calib 2 Press Enter and use the Up Down buttons to choose the different color temperatures 3 There are 11 pre programmed White colors and RGB TO WHITE They can be edited by mixing Red Green and Blue 8 Zoom 1 Press Menu until the display shows Zoom 2 Press Enter and use t
10. T One Expression 33000 Built en Multiple Expression 33000 Master Slave control Multiple Expression 33000s DMX control PASS Se T TTD CO OI VOCS TRE T T Uu Tm SIT m T UL T VER cee cea ers ces Gas Main Menu Options 1 Intro Menu s M m T UL Built in Programs Auto Auto 2 Custom Mode Slave Mode XS MIL os T eas eaveaneeere Channels Advanced Basic Mode Display Mode Info version Invert c O Q 7 8 Loom 9 NP O eee 16 Channels ADVANCED 12 Channels BASIC 11 Channels G1 TCISD ed PEDIG FU TRO IONS SO ON remm NO LIGNT No Movement ALPIOOGUCI m de ee a me ee node Product Specifications 2 28 28 28 28 Unpacking Instructions Immediately upon receiving this product carefully unpack the carton and check the contents ensure that all parts are present and have been received in good condition Notify the dealer immediate
11. any material over the lens Never look directly into the light source Never leave any cobles lying around Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened Do not insert objects into air vents Do not connect this device to a dimmerpack Do not switch the device on and off in short intervals as this would reduce the lamp s life Do not touch the device s housing bare handed during its operation housing becomes very hot Allow the fixture to cool for at least 5 minutes before handling Do not shake the device Avoid brute force when installing or operating the device Only use device indoor avoid contact with water or other liquids Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened Only operate the device after having familiarized with 15 functions Avoid flames and do not put close to flammable liquids or gases Always replace the lamp when It is damaged or deformed due fo the heat Always keep case closed while operating Always allow free air soace of at least 50 around the unit for ventilation Always disconnect power from the mains when device 15 not used before cleaning or when replacing lamp Only handle the power cord by the plug Never pull out the plug by tugging the power cord To ensure the longest and most efficient use of the lamp always wait 15 minutes before re applying power after a shutdown Failur
12. e display will blink once and the device will be in slave mode Run Test With this menu you are able to test the device 1 Press Menu until the display shows Intro 2 Press Enter and use the Up Down buttons to go to the Run menu 3 Press enter to open this menu Scroll through the menu until the display shows TEST 4 When you press ENTER the display will blink once and the device will start an internal test Channels Advanced Basic Mode ENTER ENTER 1 Press Menu until the display shows Intro 2 Press Enter and use the Up Down buttons to go to the Channels menu 3 Press enter to open this menu You can choose Basic 12CH Advanced 15CH or 14CH mode Use the Up Down buttons select one 4 Once you have set the desired mode press the enter button to store your setting Display Mode ENTER ENTER 1 Press Menu until the display shows Intro 2 Press Enter and use the Up Down buttons to go to the Display menu 3 Press enter to open this menu You can choose 60 close or Bright mode Use the Up Down buttons select one 4 Once you have set the desired mode press the enter button fo store your setting ENTER ENTER ENTER ENTER 17 Info version OEE 1 Press Menu until the display shows Intro 2 Press Enter and use the Up Down buttons go to the Info menu 3 Press enter to see your expression 33000 version number 2 Invert ENTER ENTER
13. e is no data received at the DMX input the LED on the control panel will not flash The problem may be The XLR cable from the controller is connected with the input of the Expression 33000 The controller is switched off or defective the cable or connector is detective or the signal wires are swapped in the input connector Note It s necessary to insert a XLR termination plug with 120 Ohm in the last fixture in order to ensure proper transmission on the DMX data link 11 Menu Overview ENTER UP DOWN UP DOWN ENTER UP DOWN ENTER UP DOWN ENTER UP DOWN ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER 12 UP DOWN UP DOWN ENTER UP DOWN UP DOWN UP DOWN ENTER UP DOWN ENTER ENTER UP DOWN ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER 13 Once you have entered a step you will see menu 5 2 5 12 A UP DOWN UP DOWN UP DOWN UP DOWN UP DOWN UP DOWN UP DOWN UP DOWN UP DOWN ENTER ENTER ENTER ENTER ENTER ENTER ENTER ENTER 14 UP DOWN UP DOWN UP DOWN UP DOWN UP DOWN MAIN MENU Y D N N L 2 D lt O m
14. e to do so could result in premature aging of the lamp and failure to the electronics that drive if Make sure that the device is not exposed to extreme heat moisture or dust Make sure that the available voltage is not higher Than stated on the rear panel Make sure that the power cord is never crimped or damaged Check the device and the power cord from time to time If the lens is obviously damaged it has to be replaced So that its functions are not impaired due to cracks or deep scratches If device is dropped or struck disconnect mains power supply immediately Have a qualified engineer inspect for safety before operating If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature If your Showtec device fails to work properly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Showtec dealer for service For adult use only Movinghead must be installed out of the reach of children Never leave the unit running unattended Never attempt to bypass the thermostatic switch or fuses For replacement use lamps and fuses of same type and rating only Replace the lamp if it becomes defective or worn out or before usage exceeds the maximum service life Allow the fixture to cool d
15. erial data link determines the number of fixtures the data link can support Important Fixtures on a serial data link must be daisy chained in one single line To comply with the EIA 485 standard no more than 30 devices should be connected on one link Connecting more than 30 fixtures on one serial data link without the use of a DMX optically isolated splitter may result in deterioration of the digital DMX signal Maximum recommended data link distance 100 meters Maximum recommended number of Expressions on DMX data link 30 fixtures Data Cabling To link fixtures together you must obtain data cables You can purchase DAP Audio certified DMX cables directly from a dealer distributor or construct your own cable If you choose to create your own cable please use data grade cables that can carry a high quality signal and are less prone to electromagnetic interference DAP Audio Certified DMX Data Cables DAP Audio cable for allround use bal XLR M 3 p gt XLR F 3 p Ordercode FLO1150 1 5m FLO13 3m FLO16 6m FLO110 10m FLO115 15m FLO120 20m e DAP Audio cable for the demanding user with exceptional audio qualities and connector made by Neutrik Ordercode FL71150 1 5m FL713 3m FL716 6m FL7110 10m Fig 3 Control Modes There modes Select built in programs e Master Slave e DMX512 Basic 12CH Advanced 15CH or GI 14CH One Expression 33000 Built in Progra
16. erse in liquid Wipe lens clean with glass cleaner and a soft cloth Do not use alcohol or solvents The front lens will require weekly cleaning as smoke fluid tends to build up residues reducing the light output very quickly The cooling fans and the internal lenses should be cleaned monthly with a soft brush Please clean internal components once a year with a light brush and vacuum cleaner Keep connections clean Disconnect electric power and then wipe the DMX and audio connections with a damp cloth Make sure connections are thoroughly dry before linking equipment or supplying electric power Replacing a Fuse Power surges short circuit or inappropriate electrical power supply may cause a fuse to burn out If the fuse burns out the product will not function whatsoever If this happens follow the directions below to do SO 1 Unplug the unit from electric power source 2 Insert a flat head screwdriver into a slot in the fuse cover Gently pry up the fuse cover The fuse will come ouf 3 Remove the used fuse If brown or unclear it is burned out 4 Insert the replacement fuse into the holder where the old fuse was Reinsert The fuse cover Be sure to use a fuse of the same type and specification See the product specification label for details Troubleshooting No Light No Movement All Products This troubleshooting guide is meant to help solve simple problems If a problem occurs carry out the steps below in sequence unti
17. he Up Down buttons to choose Pos or Pos2 3 If you use Yes the device will return the factory default setting 4 Press enter to open this menu Use the Up Down buttons to set the desired setting ENTER ENTER ENTER 9 Default 1 7 ES 1 Press Menu until the display shows Default 2 Press Enter and use the Up Down buttons to choose Yes or No 3 If you use Yes the device will return to the factory default setting 21 DMX Protocol 15 Channels Advanced Channel 1 Horizontal movement Pan Push the slider up in order fo move head horizontally PAN Gradual head adjustment from one end of the slider to the other 0 255 128 center he head can be turned by 540 and stopped at any position you wish Channel 2 Pan fine 16 bit Channel 3 Vertical movement Tilt Push the slider up in order to move head vertically TILT Gradual head adjustment from one end of the slider to the other 0 255 128 center The head can be turned by 270 and stopped at any position you wish Channel 4 Tilt fine 16 bit Channel 5 PAN TILT Speed Channel 6 Red Dimmer must be open A 0 255 Gradual adjustment Red from 0 100 Channel 7 Green Dimmer must be open A 0 255 Gradual adjustment Green from 0 100 Channel 8 Blue Dimmer must be open AN 0 255 Gradual adjustment Blue from 100 Channel 9 White Dimmer must be open 0 255 Gradual adjustment Blue from 0
18. k reversed correctly but all respond erratically or not at all to the controller Check data quality If much lower than 100 percent the problem may be a bad data link connection poor Poor data quality quality or broken cables missing termination plug or a defective fixture disturbing the link Inspect connections and cables Bad data link connection Correct poor connections Repair or replace damaged cables Data link not terminated with 120 Insert termination plug in output jack Fixtures reset eae Ohm termination plug of the last fixture on the link oe t addressing of the fixt Check add tt some respond ncorrect addressing of the fixtures eck address setting Bypass one fixture at a time until normal operation is regained unplug One of the fixtures is defective and both connectors and connect them disturbs data transmission on the directly together link Have the defective fixture serviced by a qualified technician Install a phase reversing cable erratically or not at all to the controller 3 pin XLR Out on the fixtures does between the fixtures or swap pin 2 not match pins 2 and 3 reversed and 3 in the fixture that behaves erratically Shutter closes The shutter has lost its index Contact a technician for servicing if suddenly position and the fixture is resetting the problem persists the effect The power supply settings do not Disconnect fixture Check settings No light ma
19. l a solution is found Once the unit operates properly do not carry out following steps If the light effect does not operate properly refer servicing to a technician Response Suspect three potential problem areas the power supply the lamp the fuse 1 Power supply Check that the unit is plugged into an appropriate power supply 2 Ihe LEDs Return the Expression 33000 to your Showtec dealer 3 The fuse Replace the fuse See page 28 for replacing the fuse No Response to DMX Response Suspect the DMX cable or connectors a controller malfunction a light effect DMX card malfunction 1 Check the DMX cable Unplug the unit change the DMX cable then reconnect to electrical power Try your DMX control again 2 Determine whether the controller or light effect is at fault Does the controller operate properly with other DMX products If not take the controller in for repair If so take the DMX cable and the light effect to a qualified technician See next page for more problem solving 28 Probable cause s No power fo the fixture Check that power is switched on One or more and cables are plugged in Primary fuse blown Replace fuse completely dead Fixtures reset The controller is not connected Connect controller 3 pin XLR Out of the controller Install a phase reversing cable does not match XLR Out of the first between the controller and the first fixture on the link i e signal is fixture on the lin
20. lation yourself Always let the installation be carried out by an authorized dealer Procedure the projector is lowered from the ceiling or high joists professional trussing systems have be used Usea clamp to mount the projector with the mounting bracket to the trussing system e The projector must never be fixed swinging freely in the room The installation must always be secured with a safety attachment e g an appropriate safety net or safety cable e When rigging derigging or servicing the projector always make sure that the area below the installation place is blocked and staying in the area is forbidden The Expression 33000 can be placed on a flat stage floor or mounted any kind of truss by a clamp Mounting a clamp to the underside of the Expression moving head Eye for safety cable Unlocked Locked Improper installation can cause serious damage to people and property 4 Connection with the mains Connect the device to the mains with the power plug Always pay attention that the right color cable is connected the right place International EU Cable UK Cable US Cable BROWN YELLOW COPPER FASE BLUE BLACK SILVER NUL YELLOW GREEN GREEN GREEN EARTH Make sure that the device is always connected properly to the earth ae A Return Procedure A Returned merchandise must be sent prepaid and in the original packing call tags will not be issued Package must be clearly labeled with a Re
21. ly and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling Save the carton and all packing materials In the event that a fixture must be returned to the factory it is important that the fixture be returned in the original factory box and packing Your shipment includes e Showtec Indigo 33000 LED with Volex IEC powercable 1 5m e 2 brackets for truss mounting Safety cable e User manual LED Expected Lifespan LEDs gradually decline in brightness over time HEAT is the dominant factor that leads to the acceleration of this decline Packaged in clusters LEDs exhibit higher operating temperatures than in ideal or singular optimum conditions For this reason when all color LEDs are used at their fullest intensity life of the LEDs is significantly reduced It is estimated that a viable litespan of 40 000 to 50 000 hours will be achieved under normal operational conditions If improving on this lifesoan expectancy is of a higher priority place care in providing for lower operational temperatures This may include climatic environmental and the reduction of overall projection intensity CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing SAFETY INSTRUCTIONS Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions of this manual CAUTION
22. ms 1 Fasten the effect light onto firm trussing Leave at least 0 5 meter on all sides for air circulation 2 When the Expression 33000 is not connected by a DMX cable it functions as a stand alone device Please see page 16 for more information about the built in programs Multiple Expressions Master Slave control 1 Fasten the effect light onto firm trussing Leave at least 0 5 meter on all sides for air circulation 2 Use a 3 p XLR cable to connect the Expression 33000 The pins l Earth 2 Signal 3 Signal 3 Link the units as shown in Fig 4 Connect a DMX signal cable from the first Unit s DMX out socket to the second unit s in socket Repeat this process link the second third and fourth units You can use the same functions on the master device as described on page 16 Built in Programs This means on the master device you can set your desired operation Mode and all slave devices will react the same as the master device Multiple Expressions Master Slave control Multiple Expressions DMX Control 1 Fasten the effect light onto firm trussing Leave at least 1 meter all sides for air circulation 2 Always use a safety cable ordercode 70140 70141 3 Use 3 p XLR cable to connect the Expressions and other devices Occupation of the X LR connecti on DMX OUTPUT DMX input XLR mounting socket XLR mounti ng pl ug 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Sig
23. n be turned by 270 and stopped at any position you wish Channel 4 Tilt fine 16 bit Channel 5 PAN TILT Speed 0 255 From Max Speed 0 to Min Speed 255 Channel 6 Red Dimmer must be open A 0 255 Gradual adjustment Red 0 100 Channel 7 Green Dimmer must be open A 02255 Gradual adjustment Green from 0 100 Channel 8 Blue Dimmer must be open AN 0 255 Gradual adjustment Blue from 100 Channel 9 White Dimmer must be open 0 255 Gradual adjustment Blue from 0 100 Channel 10 Amber Dimmer must be open A 0 255 Gradual adjustment Blue from 0 100 Channel 11 Dimmer intensity 0 255 From black to brightest Channel 12 Shutter Strobe Dimmer must be open A Open 10 255 Strobe effect from slow fast 0 10 flashes sec Channel 13 Zoom 0 255 Zoom Channel 14 Control No Function Blackout during Pan Tilt movement Disabled blackout during Pan Tilf movement Fan Auto activated after 5 seconds Fan Slow activated after 5 seconds Fan Normal activated after 5 seconds Fan Fast activated after 5 seconds Auto activated after 5 seconds Auto 2 activated after 5 seconds Channel settings 41368 Indigo 33000 Fixture settings 2 15 55 255 251 255 White 1 10000 246 250 White 1 8500K 241 245 White 1 8000K 236 240 White 1 7200K 231 235 White 1 6500K 226 230 White 1 5900K 221 225 White 1 5600K 216 220 White 1
24. nal The transformation of the controller line of 3 pins and 5 pins plug and socket 5 Pins canon socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4 N C Pin 5 N C 3 Pins canon plug Pin 1 GND screen Pin 2 Signal Pin 3 Signal 5 Pins canon plug Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4 N C Pin 5 wi 3 Pins canon socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal 4 Link the units as shown in figure 5 Connect a DMX signal cable from the first unit s DMX out socket to the second unit s in socket Repeat this process to link the second third and fourth units 5 Supply electric power Plug electric mains power cords into each unit s IEC socket then plug the other end of the mains power cord into proper electric power supply sockets starting with the first unit Do not supply power before the whole system is set up and connected properly Multiple Expressions DMX Set Up DMX 512 SSS Cu vem poo p MEM M eS ee EE SLMS es SM M O VR ROO A MUR EES TEI M 4 1 OR 6 Mim n Note Link all cables before connecting electric power 10 The Expression 33000 can be operated with a controller in control mode or without the controller in stand alone mode C
25. of the delivery Any return shipment has to be made post paid at all times Return shipments must be accompanied with a letter defining the reason for return shipment Non prepaid return shipments will be refused unless otherwise agreed in writing Complaints against us must be made known in writing or by fax within 10 working days after receipt of the invoice After this period complaints will not be handled anymore Complaints will only then be considered if the client has so far complied with all parts of the agreement regardless of the agreement of which the obligation is resulting Description of the device Features The Showtec Expression 33000 is a moving head with high output and great effects Input voltage 100 240V AC e Peak power 588 Watt e Continuous Power 313 Watt Volex IEC power connector LED Quantity 22x Red 22x Green 22x Blue 12x White 12x Amber e Electronic zoom 8 40 degrees Output Lux 2m 33000 Lumen 2m 5600 e Dimmer 0 100 electronic dimmer e Strobe 0 20 7 e RGBW Color mixing 8 to 40 degrees zoom function Fast pan and tilt movement DIM 4 technology to simulate a halogen dimming curve Lightweight Color temperature presets 3200 10 000K Pan 0 540 ilt O 270 e Pan Tilt resolution 8 16 bit Special Pan Tilf movement blackout e User selectable pan tilt ranges e Basic 12CH Advanced 15CH or G1 14CH operating modes
26. ontrol Panel A A LCD Display D Up Button B MENU button E Down Button C ENTER Button Control Mode The fixtures are individually addressed on a data link and connected to the controller The fixtures respond to the DMX signal from the controller When you select the DMX address and save it the controller will display the saved DMX address the next time DMX Addressing The control panel on the front side of the base allows you to assign the DMX fixture address which is the first channel from which the Expression 33000 will respond to the controller Please note when you use the controller the unit has 15 channels When using multiple Expressions make sure you set the DMX addresses right Therefore the DMX address of the first Expression 33000 should be 1 001 the DMX address of the second Expression 33000 should be 1 15 16 016 the DMX address of the third Expression 33000 should be 16 15 31 031 etc Please be sure that you don t have any overlapping channels in order to control each Expression 33000 correctly If two or more Expressions are addressed similarly they will work similarly For address settings please refer to the instructions under Addressing Controlling After having addressed all Expression 33000 fixtures you may now start operating these via your lighting controller Note After switching on the Expression 33000 will automatically detect whether DMX 512 data is received or not If ther
27. ontrol the device by DMX 1 Press Menu until the display shows Intro 2 Press Enter and use the Up Down buttons go the Run menu 3 Press enter to open this menu Scroll through the menu until the display shows DMX512 4 Once you have set DMX control press the enter button to store your setting The device will be DMX Controlled Built in Programs Mode With this menu you can select 3 different Programs when using the Expression 33000 El 1 Press Menu until the display shows Intro 2 Press Enter and use the Up Down buttons go to the Operation menu 3 Press enter to open this menu Scroll through the menu until the display shows Auto1 Auto2 Custom You have 3 options control the device as a stand alone device 4 Once you have chosen your desired mode press the enter button to store your setting The device will start the built in program 16 Built in Programs Auto_1 Auto_2 The device will play its built in stand alone programs Custom Mode For a custom program to run you have to enter some values first For more information please see Edit menu Slave Mode With this menu you are able to set the device as a slave device EU 1 Press Menu until the display shows Intro 2 Press Enter and use the Up Down buttons to go to the Run menu 3 Press enter to open this menu Scroll through the menu until the display shows Slave 4 When you press ENTER th
28. ovement blackout User selectable pan tilt ranges IP rating IP 20 Less heat Forced cooling fan Fan Speed Control Bright LCD display Control DMX 512 Master Slave Output Lux 2m 33000 Lumen 2m 5600 60 mm 5 148 230 mm 200 mm 310 mm 34 Max ambient temperature ta 40 C Max housing temperature fg 80 C Cooling 2 axial fans 1 fan in the projector and 1 in the base 60x 0x20mm Fan in the base 95x95x25mm Fan in the head Motor high quality stepping motor controlled by microprocessors Minimum distance Minimum distance from flammable surfaces 0 5m Minimum distance to lighted object 1 3m Design and product specifications are subject to change without prior notice Website www Showtec info Email service highlite nl 30 339 mm 265 mm 296 2011 Showtec
29. own for 15 minutes before opening the fixture and replacing lamp Protect your hands and eyes with gloves and safety glasses This device falls under protection class Therefore it is essential to connect the yellow green conductor fo earth During the initial start up some smoke or smell may arise This is a normal process and does necessarily mean that the device is defective Repairs servicing and electric connection must be carried out by a qualified technician WARRANTY Till one year after date of purchase CAUTION EYEDAMAGES AN Avoid looking directly into the light source meant especially for epileptics OPERATING DETERMINATIONS e This device Is not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects The minimum distance between light output and the illuminated surface must be more than 1 meter The maximum ambient temperature ta 45 C must never be exceeded f this device is operated in any other way than the one described in this manual the product may suffer damages and the warranty becomes void e Any other operation may lead to dangers like short circuit burns electric shock lamp explosion crash etc You endanger your own safety and the safety of others Rigging Please follow the European and national guidelines concerning rigging trussing and all other safety issues Do not attempt the instal
30. tch local AC voltage and and correct if necessary frequency LEDs damaged Disconnect fixture and return your dealer Allow fixture to cool Lamp cuts out Fixture is too hot Clean fan intermittently Make sure air vents at control panel and front lens are not blocked Turn up the air conditioning The power supply settings do not Disconnect fixture Check settings match local AC voltage and and correct if necessary frequency 29 Product Specification Model Showtec Expression 33000 Voltage 100 240V 50Hz Peak power 588 Watt Continuous Power 313 Watt Fuse T5A 250V Dimensions 310x296x460mm LxWxH Weight 10 15 kg Operation and Programming Signal pin OUT pin 1 earth pin 2 pin 3 Set Up and Addressing LED control panel DMX Channels Basic 12CH Advanced 15CH or G1 14CH operating modes Signal input 3 and 5 pin XLR male T Signal output 3 and 5 pin XLR female F Electro mechanical effects LED Quantity 22x Red 22x Green 22x Blue 12x White 12x Amber Volex IEC power connector Electronic zoom 8 40 degrees Dimmer 0 10076 electronic dimmer Strobe 0 20Hz RGBW Colormixing 8 to 40 degrees zoom function Fast pan and tilt movement DIM 4 technology to similute halogen dimming curve 23 mm Lightweight Colortemperature presets 3200 10 000K Pan 0 540 Tilt 0 270 E omm 35 Pan Tilt resolution 8 16 bit Special Pan Tilt m
31. turn Authorization Number RMA number Products returned without an RMA number will be refused Highlite will not accept the returned goods or any responsibility Call Highlite 0031 455667723 or mail aftersalesghighlite nl and request an RMA prior to shipping the fixture Be prepared to provide the model number serial number and a brief description of the cause for the return Be sure to properly pack fixture any shipping damage resulting from inadequate packaging is the customer s responsibility Highlite reserves the right to use its own discretion to repair or replace product s As a suggestion proper UPS packing or double boxing is always a safe method to use Note If you are given an RMA number please include the following information on a piece of paper inside the box 1 Your name 2 Your address 3 Your phone number 4 A brief description of the symptoms Claims The client has the obligation to check the delivered goods immediately upon delivery for any short comings and or visible defects or perform this check after our announcement that the goods are at their disposal Damage incurred in shipping is the responsibility of the shipper therefore the damage must be reported to the carrier upon receipt of merchandise It is the customer s responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping Transportation damage has to be reported to us within one day after receipt

Expression 33000 Zoom

Contents

Download Pdf Manuals

Related Search

Related Contents