ACR USER MANUAL - Whaley Food Service
Contents
1. edit program Access Activate the program menu middle selection button delete program If a pin code has been set test program 1 Use the rotation pad to enter the pin code 2 Press the right arrow to enter the next alphabetic sort number 3 Press OK twice 4 Select the desired action Use arrows to select action 7 2 Adding programs 1 Select add program 2 Press OK program edit program name 7 2 1 Enter the program name 1 1 Enter the first character by using the rotation pad The name can consist of numbers 0 9 e and character or blank The combination is free to choose A name cannot have more than 11 characters including blanks You can create a blank by skipping a position This can be done by pressing the right arrow 2 Press OK or the right arrow to go to the next position Use arrows to edit name 3 Repeat steps 1 and 2 for the letter number of the name if needed Select the next position with the right arrow Press OK twice to store the name and to proceed Select next Press OK SO oS EN 28 40 9123833 1205 LX fri jado ACR LL 7 2 2 Programming cooking step program The table on the screen contains the following columns e Time duration e Temperature Row 1 shows step 1 row 2 shows step 2 etc There can be no more than 9 steps A selected cell shows an orange frame2. ZEE made ACR USER MANUAL ACR SERIES EN Original Instruction 9123833 1205 ZEE fri jado ACR KEEP THIS USER MANUAL FOR FUTURE USE 2012 Fri Jado BV Etten Leur The Netherlands We advise you to contact your supplier for the guarantee period and conditions Further we refer to our General Terms and Conditions for Sales and Delivery that are available upon request The manufacturer does not accept any liability for damage or injury caused by failing to adhere to these regulations or by not observing the usual caution or care in actions operation maintenance or repair activities even if not explicitly described in this manual As a result of constant commitment to improvement it may happen that your unit deviates in detail from what is described in this manual For this reason the given instructions are only a guideline for the installation use maintenance and repair of the unit referred to in this manual This manual has been composed with the utmost care The manufacturer shall however not be held responsible for any mistakes in this manual nor for any consequences thereof The user is allowed to copy this manual for own use Further all rights are reserved and nothing in this manual may be reproduced and or made public in any way Modifications In case of unauthorised modifications in or on the unit every liability on the part of the manufacturer becomes null and void EN 2 40 9123833
3. To alter a cell it needs to be opened by selecting it and pressing OK 1 Setting the time duration 1 Select the time duration of the first cooking step This is the value in the top left of the table 2 Press OK to open the cell The cell background turns orange 3 the time duration of the step to 1 240 minutes using the rotation pad 4 Choose to skip the step 5 Press OK to close the cell The first cooking step can be set as the pre heat step Skip the time setting or enter Press to save program 2 Setting the temperature 1 Use the right arrow to select the cell in the second column 2 Press OK to open the cell 3 Set temperature using the rotation pad 4 Press OK to close the cell 3 Next cooking steps Select the first cell of the next cooking step and repeat steps 1 2 to add another cooking step EN 29 40 9123833 1205 fri jado p 7 2 3 Keeping warm HOLD ACR Steps 2 9 can be set to keep the products warm Skip setting the time duration or enter If setting the temperature the time duration will automatically be set to HOLD A keeping warm step will only be executed if this is the last program step A keeping warm step lasts infinitely and it keeps the unit at the desired temperature The temperature must be set on at least 85 C 185 F 7 2 4 Saving the program 1 Select saving program 2 Press O
4. 4 3 2 Loading the unit with meat baskets 19 4 4 ced E 19 4 5 TINS Ol OIC TT 20 4 5 1 Takingoutthe me dt TONKS caue ek Oe eed sue iE EUR 20 4 5 2 Taking out the meat baskets 20 4 6 Switching Of the SE CREE Eau ERE RR ERR ER ir Ore E o EXEUNT 21 ESTEE 22 5 1 ANE APOL 9 REED 22 5 2 Pre TEE 23 5 3 While 23 5 4 Adding extra time to the active 24 EN 4 40 9123833 1205 fri jado ACR 9 95 ID ESPTUDE 3 24 5 6 Set the timer optional 25 5 7 25 5 8 POWT MET ____ _ _____ 25 TINGS 26 6 1 ONG 26 6 2 Ta sv rets E 26 26 0 2 2 OVENI N cca M 26 6 3 Manag ET ea cece ee nsec ca peste ie eee cw a P 27 gt I 27 6 3 2 Overvi
5. a cloth and cleaning agent 3 Remount the fan plate EN 34 40 9123833 1205 ZEE fri jado ACR 9 MALFUNCTIONS AND SERVICE WHAT TO DO Before you contact your supplier dealer in case of a malfunction there are some items you can check yourself 5 the power supply working properly Check fuses and differential switch e Has the timer clock been properly set Malfunction Possible action Cleaning Leaks water during cleaning e Door not closed correctly e Check door seal replace if necessary Cleaning Oven not clean after cleaning e Not enough detergent check cycle supply e No water supply check e Drain polluted clean e Drain valve not working properly check cleaning e Rinse can empty correctly Fan Fan not spinning e Remove the plug from the socket e Open the door e Remove fan plate see section 8 3 and check what s blocking the fan blade section 8 3 Does not light up e Set OFF in manager menu e Defect refer to section 9 2 Leaks Fat e Fat tray not placed correctly Oven Product is not getting done e Try a lower cooking equally temperature Check fuses and or the differential switch Oven The oven does not heat up Open and close door Check fuses and or the differential switch Replace see section 9 1 9 1 Replacing the mains cord WARNING Hazardous electrical voltage If the mains cord is damaged it must be replaced by the manufacturer his servi
6. been designed for grilling meat products and has a special self cleaning feature Any other use will not be regarded as intended use The manufacturer accepts no liability whatsoever for loss or injury caused by failing to strictly adhere to the safety guidelines and instructions in this manual or due to carelessness during installation use maintenance and repair of the unit referred to in this manual and any of its accessories Use the unit in perfect technical condition only 2 3 Accessories Your unit contains the following standard accessories e Meat forks e User manual For optional accessories refer to section 11 EN 10 40 9123833 1205 EE fri jado ACR 3 INSTALLATION AND FIRST USE 3 1 Unpacking the unit Your unit is shipped using a wooden crate All units are placed on a wooden pallet Y MCN Ay AA N Figure 3 Remove the wooden crate Remove all remaining packing materials from the unit Remove the protective foil from the metal parts Take off the standard accessories Eo All packing materials used for this unit are suited for recycling After unpacking check the state of the unit In case of damage store the packing material and contact the transporter within fifteen working days after receiving the goods EN 11 40 9123833 1205 ZEE fri jado ACR 3 2 Installation and positioning WARNING The unit must be installed
7. by a certified electrician Figure 4 Positioning e The user must have sufficient freedom of movement to properly operate the unit e ambient temperature of the unit must be between 10 and 30 50 and 86 F e Use proper lifting and transport tools to move the unit e Place the unit using a spirit level flat a solid surface Mind the weight of the unit e The distances between the sides and other units walls must be at least 100 mm 4 e he minimum distance between the operator side and possible glass panes or wooden partition walls must be at least 250 mm 10 The same is valid for the customer side e he space between the unit and the surface it is put on must be kept clear for proper ventilation of the electrical compartment e Keep a distance of at least 500 mm 20 of free space above the unit e Incase of a wheeled unit the floor must be flat and levelled e he products inside the unit must be clearly visible e Keep children away from the operating side of the unit Installation Secure the unit to the building structure using the tether bracket refer to the installation manual The unit has a mains plug and must be connected to a wall socket with the proper mains voltage The wall socket must be mounted by a certified electrician A water connection with an aerated valve with a inch thread connection with a minimum continuous flow rate of 15 litres min must be available near the unit The water
8. dry and clean cloth Ready completed 38 5 Close the door message Press start to resume 6 Press START PAUSE operate Press Start to resume Ready in rnin completed 100 EN 14 40 9123833 1205 A fri jado ACR Metal odour To remove both the oil and metal odour that will appear at first use the unit must be heated at the maximum temperature for at least half an hour RM z a Jf 3 Press ON OFF seconds on to switch on the unit Press OK the display the menu Create a new program containing ONE step of 250 C 482 F and a duration of at least 30 minutes See section 7 4 Select tab Operate to return to the operation field 5 Select the new program and press START PAUSE to start See section 4 6 Allow the unit to fully execute the program DIS The unit is ready for use EN 15 40 9123833 1205 fri jado ACR 4 OPERATION AND USE 4 1 Control panel SELECTION BUTTONS DISPLAY SCREEN START ROTOR BUTTON PAUSE ON OK BUTTON OFF STOP CANCEL ROTATION PAD DIAL SELECTION BUTTONS Selecting tabs in display screen ON OFF Switching the unit on and off START PAUSE Starting and ending a program Rotation pad This pad is used for e Navigating through the menu items in the screen e Changing the settings Changing
9. other point through the drum sticks Don t forget to include the wings 2 Leave some space between the products for an even exposure and browning 3 Putthe meat forks onto the rotor disks in such a way that during grilling the chicken breasts face the operator 4 Putthe points of the meat forks through the appropriate holes in the rotor disks see Figure 7 5 The other end of the meat forks must be put through the corresponding holes in the opposite rotor disk Figure 7 6 insert the remaining meat forks in the unit act as follows e Switch on the unit using the on off button e With the door opened use the rotor button to move the rotor to easily insert the next meat fork Keep the rotor button pressed until the rotor reaches the desired position Repeat these steps until all products are loaded 23 Whole uncut chickens should always be grilled using the meat forks This way their natural fat will baste each other giving a perfectly slender cooking result Refer to the You Tube movie Fri Jado instruction for binding and loading chicken EN 18 40 9123833 1205 ZEE fri jado ACR E 4 3 2 Loading the unit with meat baskets accessory Figure 8 If you use meat baskets act as follows 1 Place one end of the accessory on the bolt on the rotor end plate 2 Place the other end of the accessory on the corresponding bolt on the other rotor end plate Make sure the accessory is levelled 3
10. po eight _____ Maximum ambient S mue Sound pressure Frequency X OVE Required power KW Maexnomimacurnt 8 lngh m 22 min 40 Cleaning agent pot mt approx 800 cycle ____ Rinse agent 0 American Models ACR bottom frame 1325 1440 1130 1810 445 ACR bottom 53 3 16 56 11 16 Po epth __ 89071 po eight __ MA Weight Gross 981 ___ Net 8B temperature Sound pressure 4 70 _______________ HzO kw _ 13 35 amp Plg Nome 25 Cleaning agent mL approx 800 cycle ____ Rinse agent Depending on Country EN 37 40 9123833 1205 ZEE fri jado ACR 11 ACCESSORIES For the ACR the following accessories are available uem meat fork V spit Figure 12 A 4 F PK r j X AS eo i Y meat basket chicken rack Figure 13 EN 38 40 9123833 1205 ES fri jado ACR EN 39 40 9123833 1205 A fri jado ACR Fri Jado BV Oude Kerkstraat 2 4878 AA Etten Leur The Netherlands Tel 31 0 76 50 85 400 Fax 31 0 76 50 85 444 EN 40 40 9123833 1205
11. program is executed The changes that are made will be stored during the test mode 1 Select test program select program to test 2 Press OK PROG 1 3 Select the program 4 Press START PAUSE OK PROG 2 PROG 3 The process will be running identically to the normal execution of a cooking program During the process the program can be changed Press OK Apply the changes Select save program Press OK RON Use arrows to select program 9 06 7 6 Sorting programs This function allows you to sort programs alphabetically program 1 Select sorting alphabetically 2 Press OK alphabetic sort 3 Use arrows to select yes programs 4 Press OK yes Use arrows to select option EN 31 40 9123833 1205 fri jado ACR 8 CLEANING AND MAINTENANCE WARNING Do not use aggressive or abrasive materials These will damage the surface which will make it more difficult to remove dirt Clean the inside the removable parts and the accessories thoroughly with cleanser and water before putting the unit into use Follow the cleaning instructions as described in this chapter Treat the outer surface of the interior window with a soft cleaning agent to protect the reflection layer 8 1 Periodic maintenance Clean the interior see section 8 2 Exterior e Clean the exterior using little water cleaning agent a soft brush or a sponge e Dry the exterior with
12. 1205 ES fri jado ACR EN 3 40 9123833 1205 fri jado ACR E CONTENTS INTRODUCTION 6 1 1 E 6 1 2 encad ONCOL CMe ____ 6 1 3 Pictogramis Symbols 6 1 4 S O oa ___ ____ _ 7 TT 7 Uc EE ___ _ _____ ___________ 8 15 23 O tdoor use 4 5 45 paleo oa ones dame asco Los deacon 8 1 4 4 FAV SNCS arate ro HEP oes sc onc ace vaca 9 1 5 Service and technical support sse eee eee eee eee 9 1 6 DUO A 9 1 7 T A E 9 DESCRIP THE UNT eroe E E O 10 2 1 Ee eys sie 10 22 Intended 10 2 3 amp gt Sao 10 INSTALLATION AND FIRST 11 3 1 EIS I ERE 11 3 2 Installation and 12 9 5 alas 13 OPERATION AMD USE e 16 4 1 Ese h 16 4 2 On Ne NR mM 17 4 3 s da mU ad ot 17 4 3 1 Loading the unit with meat forks eee eee eee 17
13. K 7 3 Edit programs 1 Select Edit program 2 Press OK 3 Select the required program 4 Press OK Edit the program name Select the position of the character Change the character using the rotation pad Use a blank to erase a character Repeat steps 1 and 2 if needed Select next Press OK CI Edit the cooking steps 1 Select the cell 2 Press OK The cell background turns orange 3 Set the value using the rotation pad 4 Press OK to close the cell 5 Repeat steps 1 4 if needed 6 Select save program 7 Press OK 7 4 Deleting programs 33 Deleting of a program cannot be undone Select delete program Press OK Select the program Press OK Check whether the program name matches the program you wish to delete Select yes if this is the case Select if not Press OK DES EN 30 40 program select program to edit PROG 1 PROG 2 PROG 3 Use arrows to select program 8 14 program Delete PROG 3 yes Use arrows to select option 9123833 1205 I fri jado ACR pu 7 5 Testing the programs In the test mode the program will run normally but the settings can be changed during the process 23 Changes that are made during testing in the steps that already are passed will not affect the products in the unit However the changes will be stored and will be active the next time the
14. T PAUSE again to resume the program operate Interrupt definitely PROG 1 1 Press STOP CANCEL 2 Select yes 3 Press OK yes Use arrows to select option EN 24 40 9123833 1205 fri jado ACR 5 6 Set the timer optional This function allows the user to automatically start a program on a pre determined date and time To enable this function the timer function in the Manager menu must be set to YES 1 Select the recipe timer off operate 2 Press OK 3 Use the arrows to change the setting timer edit timer program function from OFF to This setting timer function switches the timer off or on 4 Press OK twice program PROG 2 5 Use the arrows to select the desired program and press OK set time 16 25 6 Select Set and press 7 Set the desired time using the rotation pad By set date 11 4 2008 pressing OK you switch form hours to minutes and consequently to save Press OK to save the time setting 8 Select Set date 9 Select the desired date using the right and left arrow 10 Select store to save the timer settings and to quit the menu 11 Once the timer has been set the top left of the display will show a flashing clock sign Use arrows to select action 5 7 Reset alarm signal When an alarm signal has been set it will sound To stop this signal press OK 5 8 Power do
15. Whilst loading the unit with meat baskets you must see to it that the rotor gets evenly loaded so that the mass of the products is evenly spread over de rotor causing an equal balance Also see to it that no meat parts are sticking out of the baskets Figure 9 4 4 Grilling time Grilling time depends on a number of factors e The ambient temperature and draft in the direct vicinity of the unit Grilling temperature The initial product temperature The sort of meat fat or lean and with or without additives The mass and shape of the product The total amount of meat to be grilled in one grilling cycle The end result EN 19 40 9123833 1205 ZEE fri jado ACR 4 5 Taking out the products WARNING After the grilling the interior of the unit and the glass panes are very hot Always use oven gloves when taking out the meat forks or other accessories 4 5 1 Taking out the meat forks When taking out the meat forks it is best to act as follows see Figure 10 Figure 10 1 Hold the meat fork firmly Slightly lift the end with the grips and shift the meat fork into the direction of its points This releases the meat fork 3 Take the meat fork at its other end and take it out of the unit 4 Remove the products from the meat fork 33 Refer to the You Tube movie Fri Jado instruction for unloading chicken from a rotisserie 4 5 2 Taking out the meat baskets accessories For taking out the meat ba
16. a cloth e Use Stainless Steel cleaning spray to remove stains and restoring the gloss Cooking area e Pay attention to proper cleanness of items inside the oven e Put back all accessories Glass panes Open the outer door Open the inner door Clean the glass panes with warm soapy water or grill cleaner Drip tray Flush the drip trays located under the inner glass and the rubber with hot water This to prevent obstruction in the drain and drip trays e Clean the drain with a drill brush Monthly place fan blate 33 For hygiene matters and optimum state of your ACR it is advised to maintain a fixed daily cleaning schedule EN 32 40 9123833 1205 ITE fri jado ACR LL 8 2 Daily Cleaning 8 2 1 Automatic cleaning cycle WARNING Meat forks and meat baskets must be removed from the equipment during the cleaning program 1 Remove all meat forks or other accessories Remove rough fat residues at the drainage grate The drainage must provide a free flow through during cleaning 3 Place the grid on the drainage with the convex side up 4 Check to be sure that there is sufficient cleaning agent and rinse present Otherwise exchange bottle Press the left hand selection key Select CLEAN Press OK D The unit will now clean itself completely independently The screen shows the status of the program operate Contact your supplier for the appropriate cleaning agents Consumption per cle
17. aning cycle approx 800 ml Consumption rinse per cleaning cycle approx 5 select program The following steps will be executed the cleaning program takes about 220 minutes PROG 1 1 Steam Cool down PROG 3 Spraying detergent 4 Soaking PROG 3 5 Steam 6 Rinse timer off 7 Steam 8 Cool down 9 Spraying detergent 10 Soaking 11 Steam 12 Rinse 13 Rinse Use arrows to select program 8 35 14 Blow tubes empty 15 Dry After finishing the cleaning program the unit switches off automatically 8 2 2 Clean the accessories 1 Place the detachable parts in a wide rinsing container filled with hot water and an appropriate cleaning agent 2 Soak these parts for one night and clean them the next day EN 33 40 9123833 1205 ZEE fri jado ACR 8 3 Fan plate and fan blade WARNING Take the power plug from the socket prior applying maintenance The fan plate with grid on the side of the ACR needs to be checked once a month and depending on the pollution even more often This way you can be sure that the ventilation will be optimal If this is not done as instructed the cooking time will increase and the unit can get overheated Figure 11 1 The plate can be detached without using tools by removing the four wing nuts see Figure 11 2 After taking off the plate can be cleaned At the same time the fan can be checked If necessary clean with
18. ce agent or a similarly qualified person in order to avoid hazards EN 35 40 9123833 1205 fri jado 9 2 Replacing a lamp WARNING Remove the power plug from the wall socket ACR Do not touch the lamps with bare hands Use a clean cloth or paper tissues when replacing the lamp WARNING Remove any moisture with alcohol or methyl spirits after the lamp has cooled down 1 Remove the power plug from the wall socket 2 Remove the 4 screws from the lamp holder Beware the frame glass and gasket will come off at the same time 3 Remove the defective lamp Move the lamp along the length to one side of the lamp holder 4 Install a new halogen lamp 240 V 100 W R7s 78 mm First press one side of the lamp into one connection point then put the lamp properly in its place and have it spring into the other connection point 5 Make sure the lamp is properly clamped between the two connection points When it has not been clamped properly it can be moved back and forth along the length until it clicks into the connection points and is firmly clamped 6 Remount the glass frame and gasket EN 36 40 C Aor OD A 9123833 1205 gt fri jado ACR 10 TECHNICAL SPECIFICATIONS WARNING Consult the identification plate to get the proper specifications of the unit The electrical data may vary from country to country European Models ____ ____ ____ Po Depth
19. ew s lt Tc Tas T sidicicccsssncsecesediscnteieansmnsisedeaectenchuarescdsanpbaasieussbevanstaadeaertenstaneseeds 27 6 4 SENIO MIOU cance 27 Te PROGRA NE TE 28 7 1 GENET EAER 28 7 2 as 28 7 2 Enter the program Namie eir 28 4 2 2 Programming COOKING e d 29 03 HOLD RE 30 30 7 3 Sel OS rl 30 7 4 30 7 5 Testing the TOE A 31 7 6 SO RUE AIS edt s MIEL M MEME Ed 31 8 CLEANING AND MAINTENANCE cccsscccccccccssseeccecseesecceeeseesscccesseeseeceeeeseeeeeeesseueeeeeesaaaees 32 8 1 Periodic maintenance sese eee ee eee eee eee 32 8 2 WERT Ru 33 8 2 1 Automatic cleaning cycle eer herr rr YE SF ere e Uo rer eb EL ne vede pa in 33 S22 leanthe vau Midas DR UDIN 33 8 3 Fan eS and fan blade oleae Om 34 9 MALFUNCTIONS AND SERVICE WHAT TO 35 9 1 R placing the mains 35 9 2 a 36 TO TECHNICAL SPECIFICATIONS 37 A CES ORE m 38 EN 5 40 9123833 1205 gt fri jado ACR 1 INTRODUCTION 1 1 General This manual is intended for the user of the ACR Auto Clean Ro
20. f the mains voltage by pulling the plug from the wall socket After that cool down the unit for at least ten minutes e The units equipped with wheels are not suited to pass ledges or obstacles higher than 10 mm 3 8 e When moving the unit always push at the centre of the unit Never on top Never at the bottom e Make sure that the wheels can move freely so they never touch the power lead see Figure 1 Figure 1 1 4 3 Outdoor use restrictions To avoid short circuiting the units may not be used outdoors unprotected Placing under a screen is allowed Figure 2 EN 8 40 9123833 1205 ZEE fri jado ACR 1 4 4 Hygiene The quality of fresh product always depends on hygiene Especially grilling products With the risk of salmonella contamination especially for chicken products you must make sure that grilled products can never be mixed with uncooked products Also contact between grilled products and hands or tools that have been in contact with raw chicken meat must be avoided at all times Hands or tools that have been in contact with raw chicken meat must be cleaned thoroughly 1 5 Service and technical support The electrical schematics of your unit is included In case of malfunctions you can contact your dealer service agent Make sure you have the following data available e Model e Serial number This data can be found on the identification plate 1 6 Storage If the
21. meters Function and values Change pin code Setting the pin code for access to the Manager Menu This pin code can also be used for access to the Program Menu e 0000 9999 Pre heat mode E NO never a pre heating 1X pre heating ONCE after switching on the unit YES always heating Pre heat delta Correction on the pre heat temperature based upon the operation temperature 50 C 90 F 50 C 90 F Lime filter The displayed value shows the remaining capacity of the lime filter in percents Lime filter replaced Reset the lime indicator back to 100 6 4 Service Menu The service menu contains settings for the language and security of the unit This can only be accessed by the supplier or a service technician EN 27 40 9123833 1205 SE fri jado ACR 7 PROGRAM 7 1 General Your dealer has programs that are loaded into the unit by means of a computer These programs vary with the composition of the product and the customer s desire and are customer dependent You can protect the cooking programs and the secured settings by changing pin code 0000 the menu into any other pin code By changing the pin code back into 0000 the protection is removed The program menu is used to store programs yourself A program can have not more than 9 steps In each step both the temperature and time can be set The memory can handle 250 programs add program program
22. ontents of this manual and carefully follow all guidelines and instructions Never change the order of the steps to be performed The management must instruct the personnel on the basis of this manual and follow all instructions and regulations The pictograms labels instructions and warning signs attached to the unit are part of the safety measures They may never be covered or removed and have to be clearly visible during the entire lifetime of the unit Immediately repair or replace damaged or illegible pictograms warnings and instructions e avoid short circuiting never clean the unit using a water hose For cleaning instructions see section 8 e During the grilling process the unit can get very hot e When the door is opened the rotor stops and the heater is de energised e The unit must be cleaned regularly to ensure proper functioning and prevent fire hazard over heating Especially the back of the fan plate e This appliance is not intended for the use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety e Children should be supervised to ensure that they do not play with the appliance EN 7 40 9123833 1205 ZEE fri jado ACR 1 4 2 Moving When moving the unit e Before moving the unit first switch of
23. pressure must be between 200 en 500 kPa 2 and 5 bar preferably at least 300kPa 3 bar Refer to the Installation Manual An open drainage with a diameter of at least 40 mm 1 6 must be available near the unit EN 12 40 9123833 1205 ZEE fri jado ACR 3 3 First use When using the unit for the first time clean the interior thoroughly with soap suds Run the Install program and heat up the unit as described below After commissioning discolouration of the cooking grilling area can occur EN 13 40 9123833 1205 IE fri jado ACR Install Program To be sure that all tubes are filled with detergent and rinse first run the install program e Place a container under fat drain in the support frame e Place bottles of detergent and rinse the support frame Place black cap on the bottle with detergent and make sure the hose strike the bottom Do the same with the white cap on the bottle with rinse NEC operate Run the install program it takes approximately 15 minutes 1 Press ON OFF for 3 seconds to switch on the unit Busy Installing Press START PAUSE message Busy Installing Tubes are filling up and the oven will be rinsed 3 After 15 min message Dry and Clean Rubbers 4 Open the door and dry the rubbers with a
24. skets you can use the same principal as described in section 4 5 1 but it is recommended to act as follows 1 Slightly lift both ends of the meat basket 2 Move either one side towards you and take out the basket from the unit Depending on the number of prepared products you may have to empty the baskets before they can be removed EN 20 40 9123833 1205 fri jado ACR 4 6 Switching off the unit TOL QS 8 EN Press buttons together and hold for approx 3 seconds EN 21 40 9123833 1205 AE fri jado ACR 5 OPERATE 5 1 Starting a program 1 Press the left hand selection button operate Select the required program The total duration of the program is shown in minutes next to the select program name of the program PROG 1 3 Press START PAUSE PROG PROG 3 timer off DAILY CLEAN Use arrows to select program 0 12 Use the rotation pad or arrow buttons to toggle between the programs 35 e timer off 15 the timer program see section 5 6 e CLEAN refer to the automatic cleaning program see section 8 1 EN 22 40 9123833 1205 SE fri jado ACR orn 5 2 Pre heating When the pre heat function is activated the unit will start this function after selecting this program The screen
25. the settings quickly e Increase value rub the pad clock wise with one finger e Decrease value rub the pad counter clock wise with one finger Screen The following tabs are present e Operate Choose between programs See section 5 e Program Creating programs See section 7 e Settings Change settings of programs See section 6 EN 16 40 9123833 1205 ZEE fri jado ACR 4 2 Switching on the unit j PAUSE 4 3 Loading the unit WARNING To protect the operator for possible hot gases the door is equipped with a two step unlocking device To open the door move the handle first clock wise then counter clock wise When the door is open press the rotor button to activate the rotor This allow easy loading or unloading the products Whilst loading the unit make sure that the rotor gets evenly loaded so that the mass of the products is evenly spread over de rotor causing an equal balance Do not allow empty meat forks meat baskets and chicken racks etc in the grilling process 4 3 1 Loading the unit with meat forks The unit will be equipped with a set of meat forks see Figure 5 Figure 5 EN 17 40 9123833 1205 fri jado ACR For preparing chicken or any other poultry you can work as follows see Figure 6 Figure 6 1 Insert one point of the meat fork through the chest at the position of the wings Insert the
26. tisserie The features and controls are being described along with directions for the safest and most efficient use in order to guarantee a long life of the unit All pictograms symbols and drawings in this manual apply to the ACR 1 2 Identification of the unit The identification plate can be found on the outside of the machine and contains the following data e Name of the supplier or the manufacturer Model Serial number Year of construction Voltage Frequency Power consumption 1 3 and symbols In this manual the following pictograms and symbols are used WARNING Possible physical injury or serious damage to the unit if the instructions are not carefully followed WARNING Hazardous electrical voltage WARNING Danger of getting injured by hot surfaces Suggestions and recommendations to simplify indicated actions Recycling symbol Direction of view symbol Qe 8 gt gt 6 40 9123833 1205 gt fri jado ACR 1 4 Safety instructions WARNING The outside of the unit can be very hot WARNING The maximum load on top of the unit may never exceed 50 kg WARNING Always use the brakes on both front wheels 1 4 1 General The user of the unit will be fully responsible for abiding the locally prevailing safety rules and regulations The unit may be operated by qualified and authorised persons only Anyone working on or with this unit must be familiar with the c
27. unit will not be used temporarily and will be stored follow these instructions e Clean the unit thoroughly e Wrap the unit from getting dusty e Store the unit in a dry non condensing environment 1 7 Disposal Dispose of the machine any components or lubricants removed from it safely in accordance with all local and national safety and environment requirements EN 9 40 9123833 1205 fri jado ACR EE 2 DESCRIPTION OF THE UNIT 2 1 Technical description The ACR uses convection heat The rotor is being wheeled by a maintenance free motor with a gear box The fan provides an equally divided heat The glass panes are equipped with a heat reflecting layer to keep the heat inside the grill The plating of the unit is made of stainless steel The mains cable has a CEE form plug The intelligent control keeps the temperature inside the unit fixed to level set by the operator During the entire process the interior of the unit will be illuminated by halogen lamps The intelligent control has a capability to store 250 different programs Each program can consist of a pre heat step with additional maximum 9 steps in which the cooking time and temperature can be set The unit has an automated cleaning program that cleanses the unit Communication through RS232 enables easy read out re work and creating of programs via a PC For this special software is available at Fri Jado 2 2 Intended use The ACR has
28. will display the current temperature on the right and the set pre heat temperature on the left When the set temperature is reached the screen will show Load PROG 2 products and a sound is activated Preheat operate Please wait Do not load oven 5 3 While cooking During the cooking process the display shows a graph with the planned temperature trajectory orange line and the current temperature light orange field Under the graph the program name and the total time is shown In the bottom of the screen the current temperature inside the unit and the remaining time are given When cook correction is switched on the total time and remaining time will be adjusted operate v total time 7 5min progran PROG stepi 2 Current temp 59 C Ready in 75min press power for extra time 15 20 23 40 9123833 1205 SE fri jado ACR 5 4 Adding extra time to the active program During the process extra time can be added by operate following the next steps Extra time in minutes 1 Press the power suton 9 2 Set extra time by rubbing the rotation pad 3 Select the arrow point right to save setting 4 Press OK The display now shows the extra time which will be added to the last cooking step The screen always shows the total amount of extra time Use dial to enter value 5 5 Interrupt a program Interrupt temporarily 1 Press START PAUSE 2 Press STAR
29. wn If no program 15 active and no key 15 touched within the next 60 minutes the unit will switch off automatically Press ON OFF for some seconds to re start the ACR This option can be both switched off or adjusted by a service engineer EN 25 40 9123833 1205 AN fri jado 6 SETTINGS 6 1 General ACR The settings of the unit can be changed by using the control panel There are three kinds of settings e Information e Manager e Service 6 2 Information 6 2 1 Access 1 Activate the settings menu right selection button 2 Select information 3 Press OK 6 2 2 Overview The screen shows for a predefined time an overview with some pre programmed settings Pressing any knob to return to the setting menu instantaneously EN 26 40 information manager service Use arrows to select setting Fri_ Jado ACR Version Serial 192 158 90 1 Ethernet 192 168 0 40 MFMB v1 11 54 1 00 WE fri jado 9123833 1205 gt ACR 6 3 Manager settings The Manager menu is used to set the parameters 6 3 1 Access information 1 Activate the settings menu right selection button manager 2 Select manager 3 Press OK service When a pin code has been set 1 Use the rotation pad to enter the pin code 2 Press OK or the right arrow to enter the next number 3 Press OK twice Use arrows to select setting 8 32 6 3 2 Overview para
Download Pdf Manuals
Related Search