USER MANUAL
Contents
1. DO SV Output TMDS Input DDC RS232 5 0 Connection and Operation 5 1 Connection 1 Connect all source devices to the HDMI inputs on the Switch Splitter 2 Either HDMI or UTP can be selected as signal output for Output A B When choosing the HDMI as signal output connect displays and main unit directly HDMI SWITCH SPLITTER 4x2 matrix by Cat5 over HDMI cable When choosing UTP as signal output connect receivers and main unit over cat5e 6 cable and then connect output of receivers to displays Note HDMI and UTP of each output can not be connected simultaneously 3 Connect the 5V 2A power supply to the Switch Splitter and 5V 2A power Supply to each receiver Note 1 Please make sure to cut off the power before insert IR Extender into the Converter 2 Please make sure to insert the plug of IR Extender into the Converter completely Attention Insert Extract cable genily 5 2 Operation 1 When supplied with power the output A and output B will select Input 1 at the same 2 Selecting source devices by buttons Two buttons on the Switch Splitter are used to select source devices circularly for outputs A and B Once you press the button it will select next available source device 3 Selecting source devices by IR remote 1 Power button The power button of the IR remote can control the power of the Switch Splitter Pressing this button the power on unit will be turned o2. For example If you want display B to view source 3 then you can input B3 and finish with Enter B Turning off an output Sequence number of the output that you want to turn off Enter For example If you want to turn off output B then you can input CB and finish with Enter C Turning off the Switch Splitter OFF Enter D Turning on the Switch Splitter ON Enter E Inquiry QS Enter This order enables you know which input and output are available and the connections of input and output 5 3 CONECTION DIAGRAM HDMI SWITCH SPLITTER 4x2 matrix by Cat5 ILI S re Infrared receiver P N3011
3. USER MANUAL Table of Contents 1 20 MED 3 0 Package 4 0 Panel 5 0 Connection and Operation HDMI SWITCH SPLITTER 4x2 matrix by Cat5 HDMI SWITCH SPLITTER Dear customer Thank you for purchasing this product For optimum performance and safety please read these instructions carefully before connecting operating or adjusting this product Please keep this manual for future reference 1 0 INTRODUCTION This 4X2 Matrix HDMI SWITCH SPLITTER by cat5e 6 offers unprecedented flexibility and convenience by routing high definition audio video from any of four HDMI video sources to any of 2 displays over HDMI cable or 2 remote displays over inexpensive standard CAT5e 6 cable It eliminates the need to disconnect and reconnect sources to a display equipped with one input Two receivers work with the Switch Splitter as a full functional module Full High Resolution HDTV signals are supported up to a resolution of 1080p over HDMI cable 15m or at a maximum distance of 40M over two pieces of CAT5e 6 cable The 4X2 Matrix HDMI SWITCH SPLITTER works with HD DVD players TiVo systems HT PCs and satellite set top boxes that connect to an HDMI display Every source and display is accessible at all times by selecting it wi
4. ff If you press it again the unit will be turned on 2 Other buttons Depending on outputs A B the other buttons of the IR remote can be divided into four groups Each group has five buttons off turn off its outputs 1 2 3 4 are used to select input port accordingly 4 Selecting source devices by RS232 D Introduction of RS232 remote operation RS232 remote operation is mainly based on the super terminal of Windows operation system Its parameter should be ANSI 4800 8 N 1 non 2 Operation A Connect the switch splitter to the COM of PC with a RS232 cable B Chose the right COM when you setting super terminal and then set the parameter as follow Baud frequency 4800 Data bit 8 Parity bit N Stop bit 1 Data stream NON C Inputting your instruction The instruction should be two or three letter and finish with Enter button HDMI SWITCH SPLITTER 4x2 matrix by Cat5 Please input next instruction in three seconds or the Overtime instruction will appear The input instruction should be right or you will be rejected with the wrong instruction If the input or output that you chose is not connected to devices or not in power on mode ineffective instruction will inform you If your instruction is performed you can see the instruction of successful operation 8 Instruction inout method A Selecting source device Sequence number of output A B sequence number of the input 1 2 3 4 Enter
5. ing Temperature 0 C to 0C Operating Humidity 1096 to 85 RH no condensation otorage Temperature 10 C to 80 PowerRequirement Regulatory Approvals Accessories Adapter J __ 10 10 10 Note Specifications are subject to change without notice otorage Humidity 5 to 90 RH no condensation 3 0 Package Contents Before attempting to use this unit please check the packaging and make sure the following items are contained in the shipping carton Packaging of Main Unit 1 HDMI 4X2 Switch Splitter HDMI SWITCH SPLITTER 4x2 matrix by Cat5 2 Remote Control 3 Infrared Extender IR 4 5V 2A DC Power Supply 5 User s Manual Packaging of Accessories 6 Two Receivers 7 Two pieces of Remote Control for Receivers 8 Two pieces of External infrared emitter IE 9 Two pieces of 5V DC Power Supply 4 0 PANEL DESCRIPTIONS Please study the panel drawings below and become familiar with the structure HDMI 4X2 Matrix By CAT 5e 6 Select Select C D Input 34 o Q 6 o o 6 6 o o d Standby 1 2 3 4 1 2 3 15232 IR Ext Power IR OutputA OutputB FE CE Made China x Inputl Inputs 1E4 Input4 Receiver Select IR Power 1 2 3 4 C C
6. th an IR remote front panel buttons or through RS232 port 1 1 FEATURES This product has many features that enable it to perform in a superior manner Among those features you will find Allows any HDMI display to view any source at any time Allows any source to be displayed on multiple displays at the same time HDMI or DVI to HDMI cables are used to connect the inputs and the matrix output Each Output includes one HDMI output and UTP output over cat5e 6 but only one way is available at a time Each UTP output is connected to a Receiver UTP output extends signal up to 40m for 1080p by UTP cable with cross stand inside Each Input includes an infrared Emitter which is used to control the long distance source device by Remote Control Each display s inputs can be switched with the IR remote control front panel buttons or through RS232 Supports highest video resolution 1080p Supports 225MHz 2 25Gbps per channel 6 75Gbps all channel bandwidth Supports 12bit per channel 36bit all channel deep color Supports HDCP Supports uncompressed audio such as LPCM Supports compressed audio such as DIS Digital Dolby Digital Cincluding DTS HD and Dolby True HD HDMI SWITCH SPLITTER 4x2 matrix by Cat5 2 0 SPECIFICATIONS Signal Inputs Output J o S Operating Frequency o 0 Resolutions HDTV J Mechanical 0 00 Warranty Environmental Operat
Download Pdf Manuals
Related Search