B.Braun Infusomat fmS - Frank`s Hospital Workshop
Contents
1. Check regularly Check for cleanliness completeness and damage Use only according to Instructions for Use Check each time when switching on self check audible alarm process and alarm control indication Cleaning Clean using mild soap suds Do not use spray disinfectants at the mains power connection Recommended disinfectant for wiping available from B Braun e g Meliseptol Before operation the device allow to vent for at least 1 min Do not spray into openings in the device Be sure to observe the instructions provided concerning waste disposal and hygiene for batteries and disposables Items included Infusomat fmS Power Cord Drop Sensor Pole Clamp Instructions for Use Ordering Infusomat fmS 230 V Infusomat fmS 200 240 V Infusomat fmS 100 120 V Recommended accessories for Infusomat fmS Connecting lead for potential equalisation MFC Connecting lead for staff call MFC Connecting lead for ambulance cars 12 V DC MFC RS 232 interface lead with electrical isolation Short stand with drop chamber holder Original Infusomat infusion set CVP with line for CVP measuring 340 cm Original Infusomat infusion line 250 cm Original Infusomat infusion set 5 um with 5 um filter 275 cm Original Infusomat infusion set K with injection port 270 cm Original Infusomat infusion line S black for light sensitive drugs 250 cm Original Infusomat infusion set E for enteral nutrition2. C with OIL infusion set Mechanical occlusion pressure limit under fault conditions Alarm in case of incorrect dosage KOR rate KVO Technical sensitivity Air bubbles gt 0 01 ml Alarm triggering With air bubble size of typ 0 3 ml limit value 0 4 ml or 1 5 ml h cumulative value of 1 h as of air bubble volume 0 01 ml 1 Can be set from 0 01 to 0 3 ml via service program only 2 Can be set from 0 5 to 3 5 ml h via service program only typ 5 measured values of second hour acc to IEC EN 60601 2 24 0 1 999 9 ml h 0 1 ml h increments 0 1 9999 9 ml in 0 1 ml increments low medium high rate app 0 4 bar app 0 8 bar app 1 2 bar 1 ml h 15 min 21 min 30 min 25 ml h 36 sec 52 sec 72 sec 100 ml h 9 sec 13 sec 18 sec 0 25 ml 0 35 ml 0 5 ml Occlusion alarm pressure max 1 6 bar 160 kPa max bolus volume 2 ml In case of incorrect dosage of max 0 6 ml due to apparatus malfunction the pump switches off automatically Delivery rate gt 10 ml h 3 ml h Delivery rate lt 10 ml h 1 ml h Delivery rate lt 1 ml h STOP 17 Warranty TSC Service Cleaning Responsibility of the Manufacturer The manufacturer assembler installer or importer considers himself responsible for the effects on safety reliability and performance of the equipment only if e assembly operations extensions re adjust ments modifications or repairs are carried
3. Press key below END Set Date Clock gt Set date Press key below DAT enter date and confirm with DAT Set time Press key below TIME enter time and confirm with TIME gt Exit selection Press key below END Dosage Calculation Overview The dosage calculation automatically calculates the delivery rate in ml h Setting parameters 1 Concentration per ml or quantity per volume of infusion bottle Entry mcg mg IU or mmol each from 0 001 to 99999 5 digit decimal point counts as one digit 2 Selection for weight and time related or only time related dosage Entry of body weight from 0 01 kg to 200 kg 3 Entry of dosage a Weight and time related in mcg kg mg kg IU kg mmol kg each per min h or 24 h b Only time related in mcg mg IU or mmol each per min h or 24 h Dosage Calculation Operation Press key below SF repeatedly until DOSAGE CALC OFF appears Press key below ON gt Select quantity unit Select with key below mcg Note After numerical entry change of quantity unit is not possible anymore Remedy delete numbers gt Enter concentration by moving flashing star to desired entry position with arrow keys Confirm all numbers with OK Entry of concentration per 1 ml or per volume of infusion bottle gt For dosage by body weight enter body weight and confirm Otherwise confirm O kg Select desired quantity and time unit gt Enter values
4. fluid manager system Flow Inhibitor Opening door clamps off infusion line automatically Peristaltic Pump For precise and reliable dosage Function Keys VOL Infusion Volume Press key below VOL Enter volume 0 1 9999 9 ml Confirm Press again key below VOL TIME Infusion Time Press key below TIME Enter time e g 50 min as 5 0 or 2 h 30 min as 2 3 0 Confirm Press again key below TIME RATE Delivery Rate Only active when rate is calculated automatical ly The key below RATE confirms the calculated rate SF Special Functions If activated dose calculation bolus function standby drug selection occlusion pressure drop control piggyback battery capacity data lock contrast date time Operation Infusion 1 Ensure reliable installation Never position infusion bottle below pump level gt Connect staff call Insert spike vertically into infusion bottle Fill lower part of drop chamber to max 2 3 gt Open roller clamp 2 Filling and Venting Fill infusion line from bottom to top gt Close roller clamp 3 Insert Infusion Line Press door opener gt Insert infusion line Locate clips first on top then on bottom Keep infusion line in place at air sensor gt Close door In the area of the peristaltic pump segments and free flow clamp the infusion line will be positioned self acting gt Open roller clamp completely There may not be a con
5. at flashing star as described and confirm with OK Automatically calculated values rate or dosage are displayed First check rate displayed for plausibility then confirm RATE Value is displayed gt Start infusion Note Dosage value with unit is displayed down on the right As the automatically calculated value of the rate is rounded the dosage value may change insignificantly Info Request Press key below INFO 1x Infused Volume Run Time 2x Infused Volume Actual Dose 3x Battery Capacity Operating Hours Change Rate Dosage gt Press STOP gt Enter new dosage value and confirm with RATE Start infusion again Change Rate or Dosage without Interruption of Infusion During infusion a star is flashing down on the right gt Enter new value and confirm with RATE Pump operates with new rate dosage Note Alternatively the star can be moved with the arrow key to change the rate in ml h Change Concentration with Dosage Calculation Activated Press key below SF repeatedly until DOSAGE CALC ON appears and confirm with OK gt Press CLR Concentration is cleared Enter new value and confirm Change dosage gt Press key below SF repeatedly until DOSAGE CALC ON appears and confirm with OK gt Change values move flashing star as described and confirm entries with OK 11 Special Functions gt Check entered or calculated rate for plausi bility and confirm
6. with bottle connection total length 250 cm pressure proof Original Infusomat infusion line with Y connector for Piggyback mode Piggyback connection infusion line Art Nr 871 5548 871 5440 871 5416 870 1628 871 1682 871 1674 871 1661 870 1644 870 0010 870 0036 870 0052 870 0087 870 0125 873 1934 825 0715 825 0740 19 BBRAUN HOSPITAL CARE B Braun Melsungen AG P O Box 11 20 D 34209 Melsungen Tel 49 0 56 61 71 0 Fax 49 0 56 61 71 20 44 Material No 3891 2341 Drawing No M671010100F04 05 01 Printed on pulp bleached 100 chlorine free
7. At the moment of an event also the volume infused from switching on is recorded The history function is activated ex works After a software update the function has to be installed again service programme menu 560 calibration history card With this programme the function also can be deactivated A faultless time related recording requires exact setting of time and date 8 Recording the data The protocol of events only can be transferred to a computer via interface MFC interface lead For this a terminal programme installed in the computer has to be selected settings 9600 baud 1 start 8 data 1 stopbit For the data transfer the Infusomat fmS has to be switched off and connected to mains The protocol can be requested with key and begins with the latest event Data are screened in the terminal programme of the computer To stop data transfer Press key below END The history function mainly is used for failure analysis for the technical service A data transfer via fm system is not possible Special Functions Select Special Mode SF Depending on the version several functions may be deactivated Contact service gt To set special functions press key below SF repeatedly until desired special function is displayed Then follow Instructions for Use as described Activate Bolus Function For additional boli Pressing key below ON activates the function function is maintained after switch
8. Infusomat fmS Instructions for Use Software IFME IFMe BIBRAUN Patient Safety Attention Consult accompanying documents A Read Instructions for Use prior to use Application only under regularly supervision by specially trained staff Operation gt Ensure the unit is properly positioned and secured gt Prior to use check audible and visual alarms during self test Also check the device for possible damage If staff call is used we recommend to check the equipment once after connecting the pump gt Connect to patient only after switching on the device Interrupt the connection during changing administration set s to prevent incorrect dose delivery gt Select cannula catheter suitable for use with the intended medical application gt Position the infusion line free of kinks gt Recommended change of disposables after 24 h consider national hygiene regulations gt Compare displayed value with entered value Start infusion only if values are corresponding Installation in medically used rooms must comply with the appropriate regulations e g VDE 0100 VDE 0107 or IEC publications Possible explosion hazard if used in presence of flammable anaesthetics Air in line cannot be detected by the air detector at stop cocks infusion ports and additional administration set components Other components Variations in pressure e g as caused by change of level can affect the acc
9. ccur which lead to a device alarm with permanent alarm tone see also alarm conditions page 13 Interferences may occur e g at electro magnetic fields gt 10 V m resp electro magnetic discharges gt 8 kV A Special Function without drip control see page 10 Infusomat fmS Contents Infusomat fmS Overview Page 4 Operation Page 6 Additional Settings Page 7 Special Functions Page 8 Alarm Conditions Page 13 Start up Graphs and Trumpet Curves Page 15 Technical Data Page 16 Warranty TSC Service Cleaning Page 18 Ordering Page 19 Technical Safety Check The Infusomat fmS is according to IEC EN 60601 1 resp IEC EN 60601 2 24 a volumetric infusion pump for infusion of small and large volumes at highest accuracy and is suitable for intravenous and intra arterial applications for blood transfusion and for enteral nutrition The medical specialist has to decide on the suitability of the application The decision has to be made on the basis of the specified properties and technical data For further details please refer to the Instructions for Use Overview Handle For easy transport Ar AW jr Display EHE All important information in plain text Green DAT 3 A 7 background illumination only if connected to o F mains or a key is pushed at battery operation Keypad for Input Correct Input CLEAR Display reset to 000 0 Red LED indicates alarm condi
10. com mercially available external computer this must satisfy the requirements acc to IEC EN 60601 1 as well as the single fault fail safe condition acc to IEC EN 60513 gt Documentation All operating data of the Infusomat fmS can be requested and logged via external computer Start up Graphs and Trumpet Curves Start up Graphs Trumpet Curves 2 ml h flow Delivery rale 1 ml h deviation Delivery rafe 1 ml h VCC Sess HE Tee IN TT TTT TPS T T Bea zn pmin i 30 60 90 t min 120 2 5 11 19 pAt min 31 50 ml h flow Delivery rate 25 mi h 10 deviation Delivery ratk 25 ml h 0 30 60 90 t min 120 2 5 11 19 pAt min 31 ml h flow Delivery ratd 100 ml h 10 deviation Delivery rate 100 ml h 150 5 Epmax Epmin 50 5 0 30 60 90 t min 120 2 5 11 19 pAt min 31 The graphs show the accuracy uniformity of flow in relation to time Allow for the following The delivery behaviour resp delivery accuracy is essentially influenced by the types of disposables used Significant deviations may be encountered if use is made of disposables others than those stated in the order data Trumpet Curves Start up Graphs Measurement interval Measurement duration Flow At 0 5 min p x At min At 0 5 min T 120 min Q ml h Measured values for second and last hour in each case Measurement interval Observation i
11. e g mg or in quantity of active agent per kg weight mg kg the bolus may be administered During bolus administrati on all three values are displayed Standby Pause In case of extended interruptions set values are retained Press STOP Press key below SF until Standby is displayed Press key below ON gt Enter length duration of interruption interval or confirm time displayed Correction Press C Display 00h 00m New entry gt Confirm TIME Timer for interruption on display is running Alarm at the end of interruption interval gt End of interruption interval Press key below END Special Functions Drug Display 9 selectable drug names can be stored input via service program only gt Select with key below Drug is displayed also during infusion gt Key below CLR deletes drug name from display gt Exit selection Press key below END Occlusion Pressure Due to variable pressure limits shortened alarm times are possible Occlusion pressure high medium low See Technical Data gt Select pressure with key below or Exit selection Press key below END select pressure as low as possible Switch off Drop Control Caution No alarm will be emitted if the drop control is switched off and the roller clamp is closed underdosage No alarm will be emitted in case of occlusi on within the infusion line and pressure sensor fails Drop control may only be
12. ew rate Press key below RATE Rate is transferred to the upper level as large numbers gt Pump operates at new rate If new rate is not confirmed within 10 sec infusion continues at previous rate Target Volume Volume Pre selection The target volume will be administered independent on the infused volume gt Press key below VOL gt Enter target volume via keypad and confirm with VOL Values between 0 1 and 9999 9 ml After confirming the display shows the residual volume instead of the target volume Note When target residual volume has been administered the device switches to KOR mode Stop pump and press VOL Clear displayed residual volume with C in display appears target volume ml and confirm with VOL If desired enter new target volume To continue infusion the target volume has to be displayed as ml or a new target volume has to be set Target Time Time Pre selection Press key below TIME Enter target time via keypad 50 min 50 2 h 30 min 2 3 0 gt Confirm Press key below TIME again instead of the target time the residual time is displayed now Correction Press C Display h m New entry Note When pre selected time has been expired the device switches to KOR mode Stop pump and press TIME Clear resid time with C in display appears target time h m and confirm with TIME If desired enter new target time To continue infusion t
13. he target time has to be displayed as h m or a new target time has to be set Rate Calculation Displayed delivery rate must be 000 0 gt Enter volume and time The delivery rate is calculated automatically and displayed rounded to one decimal place gt Confirm Press key below RATE gt Start infusion with START STOP Clear Time Volume Press STOP then key below VOL or TIME gt Press C to clear 1x Target Vol Time ml h m 2x Infused Volume Real Time 0 0ml 00h00m Additional Settings KOR Mode KVO After expiring of the pre selected time or infusi on of the pre selected volume automatic reduc tion to keep open rate KOR gt KOR and delivery rate flash alternately Deactivation and alarm after 30 min gt Switch off with START STOP Special Functions Status request Only when infusion is running Press 1 x resp 2 x key below INFO for actual values The display disappears after 10 sec or after all information has been requested Press 3 x key below INFO for battery capacity in h min and hours of operation History Function In connection with the software IFME the Infusomat fmS is equipped with a history func tion memory of events This permanent memory records the last 350 events time and date related Set delivery rate Changes of the rate Switching on off Start Stop of infusion Remote Control Operating and device alarms
14. ine 8250740 Y connector Ih Drop chamber U Roller clamp Infusion pump to patient Start infusion Pump delivers the piggyback volume with the set piggyback rate As soon as the programmed piggyback volume has been infused delivery continues with keep open rate KOR resp after 30 min KOR operation the pump stops and activates an alarm The operator must switch over to the primary infusion manually Close clamp of secondary medication and re open clamp of primary infusion Please note The Piggyback mode requires the input of a target volume resp a target time for the primary as well as for the secondary infusi on It also is possible to start with the primary infusion after entering the Piggyback values switch back to primary with END In STOP mode it is always possible to switch over bet ween Piggyback and primary mode Alarms Operating alarms Remedy failure and restart infusion Drop Alarm Pressure Alarm Infusion bottle empty gt Roller clamp closed gt Flow Close roller clamp Infusion STOP There may not be a continuous drip Insert new infusion line if necessary gt Occlusion Insert infusion line free of kinks and check the free flow consider bolus gt Condensed drop chamber Shake to remove gt Drop sensor fitted connected Replace drop sensor if necessary Air Alarm gt Air in administration set Insert infusion line correctly Vent and rese
15. ing on again To change bolus rate Press key below RATE Enter new value and confirm Correction Press C and re enter Exit bolus function Press key below END Bolus application during infusion Bolus with volume pre selection Press key below BOL and release Display BOLUS RELEASE gt Enter bolus Values between 0 1 and 99 9 ml if no entry is made within 10 sec function is exited automatically Press key below YES Bolus is administered After the bolus application the infusion continues at basic rate To stop bolus Press key below STOP Bolus without Volume Pre selection Press and hold BOL until a second BOL is displayed gt Hold both BOL keys Bolus is administered as long as both keys are pressed Per ml bolus administered a short audible signal sounds Interval bolus Automatic bolus in set time interval In case of manual bolus administration the interval bolus is skipped gt Select bolus function under SF Press key below VOL TIME or RATE Enter values and confirm After value below TIME has been confirmed interval times runs automati cally Exit function with END set basal rate and start Remaining interval time is displayed in h min sec A bolus on demand is possible at any time during infusion at basal rate Bolus and dosage calculation gt Operation as in volumetric mode Depending on the settings in ml volume quantity of active agent
16. is off Pump switches off automatically after a few seconds gt Switch on device again In case of repeated device alarm inform service 13 Alarms Mains Operation 12 V DC or Battery gt Check mains voltage as per type plate gt Plug in mains power lead at rear screw in 12 V DC lead in ambulance car gt In case of mains power failure or if 12 V DC or mains power is not connected the unit auto matically will be switched to integrated rechargeable battery Charge Battery gt Charge battery in case of first use battery alarm non use gt 2 months Battery is charged if 12 V DC or mains are connected even during infusion Charging Time gt Approx 16 hours Longer charging is not detrimental Capacity A fully charged battery is sufficient for more than 3 5 h with highest delivery rate Rechargeable Batteries Ageing After 2 years the original capacity is only approx 50 The lifetime of the battery can be extended by completely discharging from time to time and recharging afterwards Interface Interface Operation Connection to interface input via MFC plug Interface descriptions available from B Braun Send Proposal The delivery rate and a drug can be entered in the Infusomat fmS as proposal via an external computer Both items of data must be checked on the Infusomat fmS and acknow ledged gt Remote Control Via fm controller possible When using a
17. nterval 15 Technical Data Type of unit Classification acc to IEC EN 60601 1 Class acc to Directive 93 42 EEC Rated voltage current External extra low voltage Staff call EMC Time of operation Operating conditions Relative humidity Temperature Atmospheric pressure Storage conditions Relative humidity Temperature Atmospheric pressure Battery type rechargeable Operating time of rech battery Recharging time Weight Dimensions WxHxD 16 Volumetric infusion pump 9 defibrillator proof CF equipment Protection Class I IP 22 Moisture protection drip protected Il b 230 V AC 0 06 A 50 60 Hz Mains fuse T 0 16 A or 200 V 230 V 240 V AC 0 06 A 50 60 Hz Mains fuse T 0 16 A or 100 V 110 V 120 V AC 0 12 A 50 60 Hz Mains fuse T 0 315 A Mains voltage can be selected at appliance inlet 12 V DC Max 24V 1A 24VA Arbitrary connection polarity VDE 0834 EN 55011 IEC EN 60601 1 2 and IEC EN 60601 2 24 100 continuous operation 30 90 without condensation 10 C 40 C 700 mbar 1060 mbar 10 90 25 C 55 C 500 mbar 1060 mbar NiCd 7 2 V 1 2 Ah gt 3 5 h at highest delivery rate gt 16h Approx 3 1 kg 140 x 240 x 200 mm Air detector Accuracy of set delivery rate Delivery range Delivery pre selection Occlusion alarm pressures Alarm reaction time Max bolus volume measured at 22
18. out by persons authorised by him e the electrical installation of the relevant room complies with the appropriate require ments e g VDE 0100 0107 and or the IEC publications resp national requirements e the equipment is used in accordance with the Instructions for Use and e the Technical Safety Checks are carried out regularly The CE mark confirms that this medical prod uct complies with the Council Directive on Medical Devices 93 42 EEC dated 14th June 1993 B Braun Melsungen AG Warranty B Braun provides as from the date of delivery a warranty of 2 years for every Infusomat fmS This covers repair or replacement of parts dama ged as a result of design manufacturing errors or material defects Modifications or repairs to the unit undertaken by the owner or by third parties invalidate the warranty Inspection on Delivery Despite careful packaging the risk of transport damage cannot be entirely prevented Upon delivery please check that nothing is missing Do not use a damaged device Contact the service department 18 The warranty does not cover the following Elimination of faults attributable to incorrect inexpert handling or to normal wear and tear and rechargeable batteries Technical Safety Check Service The Technical Safety Check is recommended to be carried out every 2 years and should be documented Servicing work must be carried out exclusively by personnel instructed by B Braun
19. switched off where underdosage is not critical for the patient or where the patient is maintained under constant observation Operation without drop control only with volu me pre selection Set infusion volume The volume in the infusion bottle has to be suf ficient gt Press key below SF as many times as necessary for drop control to appear Press key below OFF no drop control appears gt To switch on again Press key below ON 10 Exit from selection Press key below END Check Battery Capacity Remaining battery life time is displayed e g battery capacity 02 h 30 min In addition the operating hours are displayed To switch off display again Press key below END gt With device switched off and mains power lead detached Briefly press O Short display of remaining battery life time after 3 sec Device switched off and mains power lead connected Permanent display of remaining bat tery life time Battery replacement is recommended if a remaining life time of less than 2 h is displayed after 16 h charging time Data Lock Interlocks keys to prevent unauthorised use Press key below ON Keys are interlocked Key release Press decimal point key then key below END Loudness control only Software IFME The loudness of the audible alarm can be adju sted in 9 steps gt Increase with key below resp decrease with key below Exit selection
20. t fluid level in drop chamber Standby Alarm Alarm after pre selected pause Switch to Standby with key below SF Then end pause with key below OFF or extend pause with key below ON Battery Pre Alarm gt Battery pre alarm 30 min before battery is discharged Alternately rate and AAA A are displayed battery indicator flashes audible alarm every 9 sec Alarm can be cleared by pressing B key The alarm continues in short intervals until the bat tery is fully discharged Battery Alarm Alternately rate and AAA A are displayed The text display shows battery discharged connect to mains battery indicator flashes red alarm indicator is on audible alarm every 4 sec operating indicator off staff call gt Switch off device Connect to mains power or 12 V DC power source KOR Alarm KVO Pre alarm audible alarm every 9 sec max 30 min End of infusion alarm Permanent interval signal tone also via staff call Delay of Alarm Tone gt When connected to staff call the alarm tone on the device can be suppressed for 10 min This function can be activated via service only Further Alarms Displays gt pump door open Close door invalid rate Enter different value Device Alarms When display indicates device alarm an audible alarm sounds permanently gt Press ON OFF key repeatedly until display indication do not press any key until display
21. tinuous drip Place drop sensor on drop chamber if necessary use an appropriate adapter 4 Switch On with Cf Green mains power control or yellow battery control alarm tone and display LED s are briefly activated 5 Puncture 6 Setting the Delivery Rate In the range 0 1 999 9 ml h and check selectable in 0 1 ml h increments Correction Press C then set new rate Select additional settings if desired see page 7 upper clip H Original Infusomat line with silicone pump element 7 Press START Operating symbol appears on the display and the green operating indicator lights 8 Stop the infusion Press STOP Green operating indicator goes out gt Close roller clamp gt Press door opener Infusion line will be clamped off when opening the door Remove infusion line First bottom then top Replacement Insert new infusion line as described Then press START again gt To end switch off Press f for 2 sec Additional Settings To Change the Delivery Rate gt Press START STOP Green operating indicator goes out gt Press C Display reset to 000 0 gt Enter new delivery rate No setting possible when C has not been pressed gt Press START STOP to restart infusion Alarm if no restart within 2 min To Change the Rate Without Interrupting the Infusion Function can be deactivated by Service staff gt Enter n
22. tion Additionally AAA A is flashing in the display Possible alarms drop alarm air alarm pressure alarm pump door open battery alarm standby alarm Operating Indicator Additional operating control indicator in display Holder for Drop Chamber Adapter for Drop Sensor Universal Pole Clamp Prevents unintended Replaceable depending on drop Attach the Infusomat fmS from movement swaying chamber size Press lateral and pull above clicking into its place To off release press the black button Guide for Short Infusion Pole fl Fj Mains Power Connection protect against ingress of moisture In case of mains power failure the pump switches to battery operation Battery operation time gt 3 5 h at highest delivery rate Automatic over load protection Mains fuse directly above the mains power connector Potential Equalisation To be connected for 9 CF applications Mains Power Supply For operation with fluid manager system Door Opener Aluminium Housing Easy care drip water protected resistant to disinfectants Special Functions SF Function Keys Soft keys Mains Power Switch ON OFF Suppress alarm tone for 2 min Infusion START STOP Multi Function Connector MFC Connection for staff call ambulances 12 V DC and inter face for fm anaes thesia fm intensive Optical Interface Infrared Interface for operation on
23. uracy of the device gt Where several infusion lines are connected on one single vascular access the possibility of their exerting a mutual influence vice versa cannot be excluded Refer to respective manufacturer s information for possible incompatibilities of equipment resp drugs Use only compatible combinations of equipment accessories working parts and disposables gt It is recommended to use original Infusomat infusion lines only gt The use of not recommended resp incompatible disposables may influence the technical specification Connected electrical equipment must comply with the relevant IEC EN publications e g IEC EN 60950 for data processing equipment The user operator is responsible for the system configuration if additional equipment is connected The international standard IEC EN 60601 1 1 has to be taken into account Safety Standards The Infusomat fmS satisfies all safety standards for medical electrical devices in compliance with IEC EN 60601 1 and IEC EN 60601 2 24 gt The EMC limits electro mangnetic compatibility according to IEC EN 60601 1 2 and IEC EN 60601 2 24 are maintained If the equipment is operated in the vicinity of other equipment which may cause high levels of interference e g HF surgical equipment nuclear spin tomography units mobile telephones etc maintain the recommended protec tive distances for these devices Under certain conditions malfunctions may o
24. with key below RATE Rate is displayed Start infusion Switch off Dosage Calculation The dosage calculation remains activated until it is switched off in Special Functions If the Infusomat fmS is switched off in the meantime all previous values except the body weight are maintained Switch off from Basic Menu gt Press key below SF display DOSISCALC ON Press DOSISCALC OFF Dosage calculation is deactivated gt With key below END back to basic menu Piggyback Function The piggyback mode offers the possibility to interrupt the current primary infusion tem porarily in order to administer a piggyback secondary medication Above the pump the piggyback infusion line 8250740 is connected with a Y connector to the administration set Infusomat line 8250715 Close clamp of pri mary infusion All infusion lines must be primed gt Select Special Function Piggyback with key SF gt Key below ON activates function remains active also after switching on the Infusomat again gt Enter primary rate and volume and confirm The softkey PIGY only will be displayed after a target volume had been entered before Press key below PIGY enter piggyback rate and volume and confirm 12 Secondary infusion e g 100 ml bag volume with delivery rate 10 ml h Primary Infusion e g 1000 ml bag volume with delivery rate 25 ml h clamp X Infusomat line 8250715 X clamp Piggyback l
Download Pdf Manuals
Related Search