User`s instruction manual MILKYWAY3
Contents
1. Master Slave mode 1 Press the function button MODE to enter Mode options 2 Press the function button until the LED panel shows SLA 3 Press the Enter button to confirm the setting The laser will now be working in Slave mode To create a Master Slave chain of units one laser has to be designated as the Master unit whilst the remaining units have to be set as Slave units To set the Master unit choose one laser and set it to your desired mode Auto mode Sound to Light mode etc Next connect all other units via DMX cables To achieve this join the DMX output of one unit to the next unit s DMX input until all lasers are connected Set all the Slave units to Slave mode see above The Slave lasers will now duplicate the actions of the Master unit Microphone sensitivity In sound activated mode the sensitivity of the internal microphone can be adjusted via the control panel To set the sensitivity level do the following OOS a G Ti mM Remote control mode The laser can be operated using the supplied handheld infra red remote control To use this remote control firstly remove the plastic tab at the bottom of the remote to activate the internal battery If necessary this can be replaced with a standard CR2025 button cell A On Off button Press button to turn laser On or Off B Music mode Press button to activate Sound to Light mode C Auto mode Press button to activate Auto mode First press is AUTO fast second press is AUTO sl2. by the user to dismantle or modify it in any way Installation instructions This product must be securely mounted with adequate fixings to hold the weight If mounted at height use a safety wire attached to the eyebolt and a secondary fixing point Position the aperture so that its emission is always directed away from people and objects that are able to reflect the emission towards people In this regard the separation distances of 3 metres vertically and 2 5 metres horizontally cited in HS G 95 and shown below must be observed Vertical bird s eye view Laser projection should be at least 3m above audience and should be below balcony level Laser projector Balcony i g NF gr pao es Vertical cross sectional view aoe ieri Ne ez Audience exclusion zone E e E gas o api A ae E J dience v GE a a cg a E oe a ve au PE SR tg least 3m ado win S uid be a pa o see jection sho A ssa08 Laser P se Laser projector Audience allowed in this zone e a gt 3 metres i F rs ae 4 Tr i No PaE dr z A S N Nip DA ae vs Unpacking Please check the contents to ensure that the product has been received in good condition I R remote control x1 pc IEC Power Lead x 1pc Safety Keys x2pcs If you find any accessory is missing or the product has arrived with any problems please contact your retailer at once This product contains no user serviceable parts so make no attempt to try to
3. allow the user to adjust settings as follows Press MODE to navigate through the options Press ENTER to select an option and adjust value using UP and DOWN buttons Press ENTER again to confirm setting Control panel options Automatic fast modes Press ENT for setting press MODE to exit AutS Automatic slow modes Sound activated modes BLOO BL99 0 100 Blue LED WLOO WL99 0 100 White LED ALOO AL99 0 100 Amber LED FLOO FL99 LED strobing time control DLOO DL99 LED gradual change time control RROO RR99I Red LASER strobing time control GRO0 GR99 Green LASER strobing time control M 00 M 99 motor rolling speed control doo1i DMX start address press MODE to exit SLAU Slave mode Stand alone modes THE laser can operate in stand alone mode one of 3 ways Auto or Sound activated Automatic fast Show Stand Alone mode Auto 1 Press the function button MODE to enter Mode options 2 Press the function button until the LED panel shows Auto 3 Press the Enter button to confirm the setting The laser will now be working in Automatic fast Stand Alone mode Automatic slow Show Stand Alone mode Auto 1 Press the function button MODE to enter Mode options 2 Press the function button until the LED panel shows Auto 3 Press the Enter button to confirm the setting The laser will now be working in Automatic slow Stand Alone mode Sound Activated Sound to Light Stand Alone mode Sound 1 Press the function button MODE to en
4. d BSEN60825 1 2007 incorporating corrigendum 2008 Disposal The Crossed Wheelie Bin symbol on the product means that the product is classed as Electrical or Electronic equipment and should not be disposed with other household or commercial waste at the end of its K useful life N agonnology
5. e only and in a dry environment Do not switch on immediately Wait until the unit reaches room temperature Do not shake the device and avoid brute force when installing or operating Do not use the device during thunderstorms and please disconnect the power Do not use solvents or aggressive detergent to clean the device Use a soft and clean cloth Do not modify the device or the connected power cord without authorisation Do not stare into the aperture This product emits hazardous levels of optical radiation and will cause serious injury to the eyes if viewed at close range This product should be securely mounted so that its output emission is always directed away from people and at objects that are able to reflect emission towards people In this regard the separation distances cited in HS G 95 should be observed The symbol Q o m determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 0 5m Replacing the fuse First disconnect from the mains power supply then remove the fuse holder above the IEC Socket to reveal the fuse Replace with the correct fuse rating as stated on the product or in the user manual Then lock the fuse holder cover back into place General maintenance Be sure to power off the fixture before conducting maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently Usa
6. ee MILK YWAY3 User s instruction manual This manual contains important information about the safe installation and use of this product Please read this instruction manual carefully before installing or operating Please keep these instructions in a safe place for future reference Introduction Thanks for choosing our laser device believing this brand new product will bring you unlimited marvel and happiness Before operating this device please read this manual thoroughly and retain it for future reference CAUTION Please read this manual fully before installing or operating this product as it contains important safety information relating to its installation and operation This Class 3B laser product emits hazardous levels of optical radiation and will cause injury to the eyes if viewed directly This product is not suitable for projection directly at audiences or other personnel This product must not be used for any form of audience scanning application and is for professional use only Important information This product is a Class 3B laser and should only be installed and used by personal who are trained in the management of laser radiation and are able to operate in accordance within the guidance given by the Health and Safety Executive HSE in HS G 95 The Radiation Safety of Lasers used for Display purposes This product contains no user serviceable parts Under no circumstances should any attempt be made
7. fix or modify this item yourself as this will invalidate the warranty We recommend you keep the original package and proof of purchase for any possible replacement or returned demand Setting up 1 Unpack the laser ensuring all packaging and tape is removed 2 Always test the laser before fixing in a permanent location 3 Connect the IEC mains plug and switch the rear power switch on 4 Insert the safety key and turn to a quarter turn clockwise At this point ensure that no one is exposed to laser radiation 5 Select which mode you want to operate the laser in 6 Leave the laser to run for 10 minutes before installing in its location Installation When mounting at height attach a safety wire to the eyebolt with an independent fixing Use the integral mounting bracket with a suitable clamp for stand or truss being fixed to When mounting directly to ceiling surfaces be sure to use adequate fixings for the supporting material Connecting to mains earth wire ground must be connected Use the supplied IEC lead to connect to the main power supply as follows International symbol Brown lve b i amwen e o For your safety please kindly pay attention to all of the warnings below Always plug in the power plug last and disconnect from the mains when the device is not in use or before cleaning Do not install and operate the device in rain or extreme heat moisture or dusty environments This device is for indoor us
8. ge and environment are contributing factors in determining frequency As a general rule fixtures should be cleaned at least twice a month Dust build up reduces light output amp performance as well as overheating This can lead to reduced life and increased mechanical wear Unplug fixture from power Use a vacuum or air compressor and a soft brush to remove dust collected on external vents and internal components Clean all glass when fixture is cold with a mild solution to the cloth or tissue and drag dirt and grime to the outside of the lens Gently polish optical surfaces until they are free of haze and lint The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequently depends on the environment in which the fixture operates damp smoky or particularly dirty surroundings can require cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days Front panel 1 2 345 1 Laser aperture 2 LED aperture 3 Power LED 4 I R remote receiver 5 Music LED Rear Panel 6 DMX input 7 DMX output 14 7 6 8109 1312 11 8 Remote power connector 9 Safety eyebolt 10 Safety lock 11 Contorl panel 12 Internal microphone 13 Sensitivity 14 Cool fan 15 IEC mains inlet 16 Mains fuse holder 17 Power switch 1516 17 Control panel FUNCTION SETTING The control panel and display
9. ow D E Color buttons Press buttons to cycle through laser s available color F Pause button Press button to pause the laser effect G Pattern Press the A is red strobing B is green strobing C is buttons blue strobing Use the 0 9 digit buttons to choose strobing speed DMX MODE The laser is equipped with 3 pin XLR connectors for DMX input and output These connectors are wired in parallel Only use a Shielded twisted pair cable designed for 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another DMX output DMX input XLR mounting sockets rear view XLR mounting plugs rear view 1 Shield 2 Signal 3 Signal Caution At the last fixture the DMX cable has to end with a terminator Solder a 120 Ohm resistor between PIN 2 and PIN 3 into a 3 pin XLR plug and plug it in the DMX output of the last fixture DMX parameters omnes ome owo 225 255 Red amp Green alternate strobing ou 005 254 Strobing show fast STROBING 255 255 Strobing to sound CH4 005 127 Clockwise rotation slow fast 134 255 Counterclockwise rotation slow fast CH5 DIMMER 000 255 0 100 DIMMER CH6 ee ie 000 255 0 100 Blue CH7 ane aan 000 255 0 100 Amber CH 8 i ane WHITE 000 127 0 100 White sa 000 255 Strobing Change Control slow fast LED STROBING Specifications MILKYWAY3 Important This product conformed to Laser amp LED Safety standar
10. ter Mode options 2 Press the function button until the LED panel shows Sound 3 Press the Enter button to confirm the setting The laser will now be working in Sound Activated Color mode manual setting mode color 1 Press the function button MODE to enter Mode options 2 Press the function button until the LED panel shows color 3 In color mode press ENT into manual setting submenu setting parameter manually to set the display effect Pressing ENT into next setting till all finished then go back to home menu DMX mode 1 Press the function button mode to enter Mode options 2 Press the function button until the LED panel shows d001 3 Press the Enter button to confirm the setting or change the address using the Up and Down buttons 4 Press the ENT button to confirm the setting The laser will now be working in DMX mod DMX mode DMX address setting 1 Ensure the unit is in DMX mode see above 2 Press the Up or Down buttons to adjust the DMX address 3 Press the Enter button to confirm the setting If multiple connected units are to be controlled in exactly the same way set all units to the same starting address e g 001 If individual control of multiple connected units is required each unit must have its own starting address This address must be at least 10 channels apart e g set the first unit to 001 and the second unit to 011 the third unit to 021 and so on The DMX controller will now control all the connected units separately
Download Pdf Manuals
Related Search