Heathro Fish Pump
Contents
1. Fish Pump Manual 2015 3 11 Rubber Wheel Heathro fish pump is on large rubber wheels so it s easy to move it over uneven terrain Make sure the air pressure is equal on both wheels and fill grease cups regularly 4 Use of Heathro Fish Pump Heathro fish pump is available in three versions electric gas and hydraulic 4 1 Electric model Before you start the fish pump 1 Make sure the main motor and priming motor is turned off 2 Fill priming tank with water until it is full 3 Ensure control cabinet is closed and turn on the main switch 4 Check the main light illuminates on the control cabinet 5 Make sure the valve on top of the swan neck is closed 6 Make sure the faucets nedenp priming tank is closed START THE PUMP PRIMING 1 Check the lights on the control cabinet for priming the pump is on 2 Check for priming the pump turned in the right direction See arrows on the pump If priming pump is turned in the wrong direction viringen for pump control cabinet exchanged 3 Run the priming pump until water flows out of the assault TURN ON MAIN PUMP TURN OF PRIMING PUMP 1 Check the lights on the control cabinet for the main pump is on 2 Make sure the belts are not slipping 3 Run the engine up to the desired speed 4 the pump sucks air to priming the pump runs while the main pump The pump will shake if there is air in the system in this case executable priming pump 5 For optimal use2. a i la Main Primer Mc aac A 40 6 FAA ob T 57 Mains FD ATVSE 31 6 Pushbutton Fl Fuse 056 400 speed K1l 2 Control Relay speed Li 3 Indicator light Main Start CB Overload breaker 1 Power supply 4 Moin Stop Motor AW Ml Prime moator 11k Vale Tite Hama an Ma Fear a Catia TITS Page 10 WWW Vaki is og TF 2015 Fish Pump Manual a Eco D Input 3400 Li Le L U GND W Main Dlsconnect Salt gt I ATVSE In Fi Run Main Stop Malin Start Ki CEI il s VF 1 Prime Start Stop Prime Run Green Red Hii RE at 53 24 I S24 su 5 7 note Prime Pump ML in Impeller Motor gt Ma a Mains Disconnect Pushbutton Fuse 0 5 400 Lontrol Relay Indicator light Overload breaker Power supply EA Motor drive 4 mator 1lkW ale 41 In Selm start Start Moir 2 STOP Stop spee speed Stop Eneroentey Page 11 WWW Vaki is VAKI 2015 Heathro Fish
3. it is very important that the pump sucks air carefully check all connections and hoses on the suction side www vaki is 8 VAKI 2015 Heathro Fish Pump Manual 4 2 Maintenance After the first 24 hours of use 1 Check the belts have proper tension Daily Maintenance 1 Flush the pump and motor with fresh water 2 Check Camlock transitions 3 Check mechanical parts Weekly maintenance 1 Lubricate the wheel bearing 2 Make sure nothing is stuck in the box that hides the belts Check if the belts are ok 3 Check the air in your tires 4 Check all hoses for leaks and transitions 5 Lubricate the bearing on the pump shaft below the pump house IMPORTANT before grease is pumped into the screw on the opposite side of the shaft removed This screw is put in place afterwards To switch on the remote control to the pump First press the POWER button so STOP button so POWER button again Child Hand terminal will start blinking green www vaki is 9 2015 Prime Start Stop Prine Fur breen EL ce Power Red L3 2 l Feza Bednionmte 5 Input 0 ALTIVAR gusting Checked Main Nscormnect Switch 5 Prime Pump 327 35 L L _ 3 p a a L3 S3 L2 51 11 Start FY 3 Fl Impeller Motor GND a i
4. Pump Manual 5 Programming the remote control If it is necessary to program the Hand Held Devices from the remote control box eg If you have a new device is made as follows 1 Open the remote control that is inside the control cabinet 2 Press registration button on the remote control see picture to light LED TOOK A flashes All transmit data is deleted and the device is ready to receive new signals 3 Turn off the power to the remote control for approx 10 sec 4 Turn on your device and contains Press the button at the bottom left down and release e Press the STOP button completely down and release Press the button at the bottom left down and release e Hand Held unit is now ready if the green light is flashing 5 Test the programming is successful 6 Press on the transmitter to the first step until the transmitter signals via an interval tone that receiver is ready for teach in mode Please release button 7 Press registration button in receivership until interval tone stops Please release button 8 Successful teach in process will be signalized by a constant tone 9 Unplug receiver for approx 10 sec 10th Please test the radio system for proper function 11th Please mark conserve transmitter i e with crane or system number in order for immediate identification EEE www vaki is Page 12
5. Wai Heathro Fish Pump User Manual Version March 2015 3 VAKI on Heathro Fish Pump Manual Contents 1 Warranty Terms of Heathro Fish Pump en 2 2 NEED OO ee ee ee ee 3 3 ol Parts ee nee een 4 ee ee E een Bee 4 3 2 er ee ee oo 4 33 MNO UO Teresa E 4 ee ee ee 5 OMA nennen ee een ee 5 3 0 a ee er 5 EF REMO COMMON ee ernennen 6 38 go a lt tc ee E A ee ee ee ee 7 Tran OT cece sete ee Se a ea ee a een aeg 7 ee ee ee 7 IE RUD OCR We ee ee ee ee 8 A UseofHeathro Fish 8 8 065 54 9 5 Programming the remote control ssccsscccvcsecesnssevenceeevsseousacsiwesurieneewsanbeuaiavetausnenesaanioecsasaessencstetaress 12 www vaki is 1 Fish Pump Manual 2015 1 Warranty Terms of Fish Pump VAKI Aquaculture Systems Ltd endorses responsible for defects occurring within one 1 year after delivery by VAKI or its reseller provided that the equipment is installed used and maintained in accordance with instructions for assembly and use undertake to repair defects caused by construction or material faults arising in the fabrication of the equipment Defects mentioned above wi
6. ed remote control and the cabinet there is a dish for good contact with the h ndheldte device It must be recharged with the battery charger supplied www vaki is 6 2015 Fish Pump Manual 3 8 Cranes On top of the swan neck there is a crane this is used to solve vacum formed on the suction side If the hose sucks getting stuck it s easy and open the tap and then get the air into the system and loose vacum On the output side there is another crane applied for and discharge hose for water and relieve the pressure before the hose is removed from the pump 3 9 Transitions There are different sizes of transitions and connections with Heathro fish pump Camlock system is used for quick and safe connection of hoses These are standard size is 6 and 4 but 5 3 can also be ordered The transitions are designed so that there are no sharp edges and the fish has a very gentle treatment during pumping Ensure that the rubber gasket is in place so not the air is sucked to the suction side 3 10 Parts Pack Many customers choose and buy a spare part package consisting of key parts that can be easily replaced 1 coupler element 2 Cover of the coupler element 3 Impellor for the Jabsco pump priming 4 Adapter ring for the motor 5 Jabsco shaft seal 6 EDPM rubber check valve gasket and the aluminum plate 7 Drive belt 2 pcs 8 Jabsco gasket www vaki is 7 a
7. he value displayed on the screen ACC is adjusted to 3 0 from the factory This value indicates how many seconds the drive to use from stop to full speed If a value that increases it will become easier and fine adjust speed 7 Use the up down arrows to adjust to the desired time Factory setting 3 0 corresponding to 2 4 Hz per press of the remote control increased to 6 0s reduced every step to 1 2 Hz Altivar 31 adjusts from to 50 Hz 8 Press Ent to save the new value 9 Press Esc to return to the ACC 10th Press down arrow to scroll to dEC does the same as the ACC but this time set the drive to use from full speed to stop 11th Press enter and the value of dEC will appear on the screen 12th Adjust to the desired value The value of ACC and dEC need not be equal If desired one can have finjustereing the ACC to run slowly speed up while a coarse adjustment has on reducing speed 13th Press Ent to save 14th Press Esc button repeatedly until rdY on screen 15th Test the new setting and adjust if necessary Section 4 14 16th When the adjustment is complete the power is turned off by turning the white shaft of the main switch counterclockwise 17th The door of the cabinet is closed 3 7 Remote Control Wireless remote control is optional and highly recommended With this you can start and stop the priming pump and the main pump and control the speed of the main pump see page 10 of the manual Inside the control box mount
8. iber glass Inside the casing there is an impellor paddle aluminum leading fish and water through the pump The speed can be adjusted as required either directly on the pump or by remote control 3 2 Main engine The main motor drives the agitator with two straps under the pump This engine is AkW and is controlled by a frequency converter Altivar 31 Thus it becomes easy to regulate the engine speed as required If wiring the socket used for the pump is inverted 3 3 Priming motor The priming motor is used for turning priming pump that created the suction that fills the main pump so the main engine can be started This motor is 1 5 kW and has no rotation protection If wiring in the socket used for the pump is inverted the engine will turned the wrong way And may get stuck If so fix the wiring and try a gene Manual force may be required to loosen the drive shaft www vaki is Page 4 a Fish Pump Manual 2015 3 4 Priming tank Priming tank is filled with water before starting the pump and the water in this tank is used to create suction in the system When water starts flowing out of the attack as the main motor is started Two cranes sit nedenpa tank one to empty the priming tank and the other to clear the actual pump housing If the pump is out in freezing temperatures can cause damage if it is not drained after use 3 5 Priming pump Priming the pump is connected to the motor by a shaf
9. ll be repaired or replaced with new ones The equipment must be returned to the manufacturer or his authorized representative for repair VAKI imposes liability for original parts are used as substitutes for a period of one 1 year from date of delivery VAKI is not responsible for Incorrect installation and use or improper care and maintenance e Defects caused by parts or materials components or equipment not supplied by VAKI and are obtained and installed or used by the customer without prior written approval from VAKI Defects caused by modifications to the equipment made by the customer without the written consent of VAKI Improper or unauthorized repairs made by the customer Normal wear and tear on equipment Improper connection of electric hydraulic equipment Defects caused by power surges Damage to electrical cables e Economic losses caused by the equipment is out of service If errors or defects occur on the equipment the customer must report as soon as possible and without unreasonable delay to VAKI or his representative Such report must be submitted no later than two 2 weeks after the guarantee period one 1 year after delivery If the customer does not inform or his authorized representative within the time limits stated above the customer will not be entitled to compensation for errors or defects Repairs to equipment shall be made in accordance with the conditions stated abo
10. t On this shaft there is a link that is easy to replace if necessary see photo below The motor is drawing a arrow showing which direction it should be reversed It is important to empty the priming pump for water if there is danger of frost 3 6 Control cabinet Control Board has seven buttons and lights The bottom is the main power button and can only be turned on if the cabinet is closed Two buttons on and off for priming the pump and two buttons on and off for the main pump It is well possible to drive the priming pump while driving the main pump The black button controls the speed of the main pump and the red light shows if there is power to the pump or not The sensitivity of the speed button can be adjusted as follows www vaki is Page 5 T VAKI or Heathro Fish Pump Manual 1 Turn off the power at the main switch and open the door of the control cabinet The door can not be opened without the main switch is turned off 2 Turn on the power in the cabinet by turning the white shaft of the main switch clockwise It is now current in all components of the closet so avoid contact with live parts 3 The Altivar 31 has four buttons and a screen It should now be rdY the screen It is an up and a down button on the left side and esc and ent knapp h yresiden of the screen 4 Press Ent once and Set appears on the screen 5 Press Ent again and the ACC will appear on the screen 6 Press Ent again and t
11. ve www vaki is 2 Fish Pump Manual 2015 2 Neighborhood Fish pump is designed to work in all weather except at temperatures below O Celsius Use in cold weather can cause damage to hoses and priming system Heathro pump is built on the wagon with 2 large rubber wheels that can carry up to 400 kg per wheel this allows the pump to move over rough and uneven surfaces The pump is designed to move the fish up to 400 g salmonids It is not suitable to pump pebbles or sand Electrical needs An electrical expert must ensure that appropriate socket is on cable VOU www vaki is 3 a Fish Pump Manual 2015 3 Explanation of Parts Heathro Fish pump is made of aluminum and fiberglass and provides a very good treatment of fish during transport The pump is 6 but can be narrowed down to 5 4 3 with transitions The pump is available in three versions an electronic which is the usual in Norway but also hydraulic and petrol driven With great handles and large rubber wheels the pump is easy to move there is need Camlock quick couplings used to obtain a simple and safe connection of hoses 3 1 Thecochlea Heathro pump is a pump and shells made from specially molded form developed by the Canadian praque Supplies They have over 20 years experience in the development and production of various products made of f
Download Pdf Manuals
Related Search