S4 User Manual.fm - Architecture And Design
Contents
1. Zo Center within the Adjust peak or flat field reflector outer knob inner knob Figure 3 seis Beam focus knob z Figure 4 2 Source Four User Manual Color frame retaining clip The color frame holder is equipped with a spring loaded retaining clip that prevents color frames and accessories from falling out Figure 5 WARNING Make sure all color frame accessories are locked in position with the retaining clip before hanging the Source Four 1 Release the retaining clip by pushing it sideways while gently pulling backwards 2 Insert the color frame 3 Lock the retaining clip by pushing sideways while gently pushing forward Color notes Fixture Soft Focus Sharp Soft Focus ETC does not guarantee the performance Version Tube Back Focus Tube Forward of saturated colors with low temperature 5 v v v ranges For best results always use a high 10 Ca v v quality and temperature color medium iS x 2 2 26 x v v ETC s Source Four color extender may help 36 P2 v x increase your gel life Contact ETC or your 50 x v v dealer for ordering information v Better gel life X Worse gel life Note An optional conical color extender 2 is available for use with saturated colors and 750W HPL lamps Shaping the beam You may shape the beam with the shutters a pattern an optional drop in iris or by rotating the barrel Pattern projection The pattern holder slot is2. clean the reflector remove the lens tube and clean the dust from the reflector with a blast of oil free air You may also wipe the reflector with a clean lint free cloth If either method is not sufficient follow the instructions below You will need a Phillips screwdriver to complete this procedure 1 Remove the barrel rotation knob located at the bottom of the barrel Use a Phillips screwdriver to remove the retainer bolt located on top of the reflector housing Rotate the barrel 45 in either direction Carefully remove the barrel from the reflector housing Dampen a clean lint free cloth with alcohol or distilled water Alcohol is recommended Gently wipe the reflector Insert the barrel into the reflector housing with the iris pattern slot on top Line up the triangles on both parts While pressing in gently rotate the barrel 45 clockwise until it sets into position Then rotate the barrel counterclockwise 45 The barrel should be firmly attached and the triangles should line up again Replace the barrel rotation knob and tighten the retainer bolt 6 Source Four User Manual Source Four User Manual 7 Electronic Theatre Controls North America 3030 Laura Lane Middleton Wisconsin 53562 e USA e Tel 1 608 831 4116 Fax 1 608 836 1736 Europe 5 Victoria Industrial Estate e Victoria Road London W3 6UU e Tel 44 181 896 1000 e Fax 44 181 896 2000 Asia Room 605 606 e To
3. from either side of the Figure 10 fixture 2 Raise or lower the fixture to the desired position within the yoke 3 Replace the yoke s hex bolts washers and locking knobs 4 Tighten the yoke knobs to secure the fixture in position Setting the angle within the yoke 1 Loosen the yoke locking knobs Do not remove them 2 Tilt the fixture to the desired position Figure 11 Yoke locking knob 3 Tighten the yoke locking knobs to secure the fixture in position Figure 11 4 Source Four User Manual Cleaning ETC offers the following recommendations when cleaning and inspecting lenses and reflectors Do not use glass or window type cleaners on lenses glass or polymer or reflectors Do not use abrasive materials such as steel wool Replace lenses if they contain visible damage cracks or deep scratches that may impair their effectiveness Cleaning 19 26 36 and 50 glass lenses 1 Remove the beam focus knob at the bottom of the barrel Remove the lens tube from the barrel Note t is not necessary to remove the lens for cleaning If you do remove the 19 26 or 50 lens make sure the identifying paint dot is not removed during cleaning 2 Dampen a clean lint free cloth with vinegar or household ammonia You may also use water but it will leave spots that can be removed by gently polishing the lens with a clean and dry cloth 3 Starting from the center gently wipe the lens 4 Sl
4. on the top side of the barrel and in front of the shutters It accommodates A size B size and glass pattern holders Figure 6 Note Because the Source Four aperture is three inches wide ETC recommends using A size patterns for maximum pattern effectiveness Use an optional donut in the accessory holder to enhance pattern projection Donut diameter range should be 2 5 to 2 75 inches Drop in iris slot The drop in iris slot is located on the top of the barrel and in front of the pattern holder slot It accommodates either a drop in iris or a motorized pattern device When the slot is not in use a small sheet metal cover secured with two Phillips Screws prevents light leakage Figure 7 1 Use a Phillips screwdriver to loosen the screws on the drop in iris slot cover Do not remove the screws 2 Slide the cover completely forward to expose the slot 3 Insert the iris or motorized pattern device For an iris install the flat side toward the shutters and make sure that the iris handle extends from the slot 4 Slide the slot cover back toward the shutters until it meets the iris handle Leave enough space to move the iris handle 5 Secure the drop in iris slot cover by tightening the screws oss Retaining clip in the e locked position Figure 5 Pattern holders am A size holds 3 diameter patterns B size holds 2 75 and 2 5 diameter patterns Drop in iris slot Figure 7 Source Four User Ma
5. Source Four User Manual Lamp housing Reflector housing Yoke Retainer bolt Shutters Pattern holder slot Drop in iris slot Color frame Color frame TUN N Lens tube Retaining clip Note Safety cable is included for cUL applications HPL lamps Do not use lamps other than the HPL in Source Four fixtures Use of lamps other than HPL will void UL cUL safety compliance and your warranty Lamp code Watts Volts Initial Lumens Color temp Average rated life HPL 750 115 750 115 21 900 3 250 K 300 hour HPL 575 115 575 115 16 520 3 250 K 300 hour HPL 575 115X 575 115 12 360 3 050 K 2 000 hour HPL 575 120 575 120 16 460 3 250 K 300 hour HPL 375 115 375 115 10 540 3 200 K 300 hour HPL 375 115X 375 115 8 068 3 000 K 1000 hour HPL 550 77 550 77 16 170 3 250 K 300 hour HPL 550 77X 550 77 12 160 3 050 K 2 000 hour HPL 750 220 750 220 19 400 3 200 K 300 hour HPL 750 230 750 230 19 400 3 200 K 300 hour HPL 750 240 750 240 19 400 3 200 K 300 hour HPL 575 230 575 230 14 900 3 200 K 400 hour HPL 575 240 575 240 14 900 3 200 K 400 hour HPL 575 230X 575 230 11 780 3 050 K 1500 hour HPL 575 240X 575 240 11 780 3 050 K 1500 hour HPL 375 230X 375 230 7800 3 050 K 1000 hour HPL 375 240X 375 240 7800 3 050 K 1000 hour Table 1 HPL lamp reference To be used with ETC Dimmer Doubler M Lens locations 19 6x16 26 6x12 Red dot Black dot A4 The diffe
6. ide the lens tube back into the barrel with the color frame retaining clip on top Replace the beam focus knob Cleaning 5 and 10 polymer lenses To quickly clean the lenses remove dust with a blast of oil free air If this is not sufficient follow the instructions below You will need a Phillips screwdriver Caution Handle polymer lenses by their edges only Never rub anything dry on a polymer lens 1 Remove the beam focus knob Gently pull the lens tube out of the barrel 2 Use a Phillips screwdriver to remove the brackets that hold the lens in place Remove the lens from the tube 3 Dip the lens in a clean alcohol water mixture 1096 alcohol 4 Use a moistened nylon bristle brush to wash the lens smooth side in a linear non circular motion 5 Use the same brush to lightly wash the lens ridged side by following its ridges 6 Dip the lens in a clean alcohol water mixture 1096 alcohol 7 Dry the smooth and ridged surfaces with an air gun Make sure that the air flow moves liquid away from you 8 Inspect the lens for dirt Repeat steps 3 7 if necessary 9 Set the lens back in the lens tube with the ridged side facing the front of the tube Replace the lens brackets 10 Slide the lens tube back into the barrel with gel frame retainer on top Replace beam focus knob Source Four User Manual 5 Cleaning the reflector WARNING Unplug the fixture before attempting to clean the reflector To quickly
7. irmly When properly installed the top of the lamp s base will be even with the top edges of the retention brackets Caution Improperly installed lamps cause premature lamp failure and socket problems 6 Press lamp retaining clip across lamp base to secure 7 Reinstall the lamp housing by aligning the bolt hole and tightening the knurled bolt Centering and adjusting the lamp The two concentric knobs located on the lamp housing allow you to align the lamp and adjust its field Figure 3 The outer knob centers the lamp within the reflector The inner knob adjusts the lamp s field 1 Turn on the Source Four and aim it at a flat surface 2 Unlock and loosen the outer knob by turning it counterclockwise 3 Gently move the outer knob from side to side and up and down until the lamp is centered within the reflector 4 Once the lamp is centered turn the outer knob clockwise to lock it in place 5 Finally turn the inner knob either clockwise or counterclockwise to achieve an optimum flat field Focusing the beam 1 Loosen the beam focus knob located under the barrel as shown in Figure 4 2 Slide the lens tube forward or backward to achieve the desired beam edge 3 Once the fixture is focused tighten the beam focus knob 8 t HPL Lamp Lamp base Lamp retention brackets lamp retaining clip 4 Knurled bolt Figure 2 Lamp housing Rear lamp housing E Ce
8. nual 3 Rotating the barrel assembly 1 Loosen the barrel rotation knob directly behind the shutters on the underside of the reflector housing Figure 8 Do not remove the barrel rotation knob 2 Rotate the barrel to the desired position up to 25 in either direction from the centered position 3 Once the barrel is positioned tighten the barrel s rotation knob to lock it into position Barrel rotation knob Figure 8 Adjusting the C clamp C clamp The C clamp attaches the fixture to the mounting pipe and allows you to adjust the Pan screw T Pipe bolt position of the fixture once it is mounted Figure 9 y Yoke bolt and 1 Tightly fasten the C clamp to the yoke with the provided yoke bolt and lock lock washer Yoke washer 2 Place the C clamp on mounting pipe then tighten the pipe bolt to secure it 3 Loosen the C clamp pan screw and rotate the yoke to the desired position 4 Tighten the pan screw to lock the fixture into position Figure 9 Adjusting the yoke position The Source Four provides multi positioning capabilities within its yoke for overall High position fixture height and angle ae IR Low position Setting the fixture height within the yoke i The Source Four has a two position yoke for modifying the overall height in which the fixture is mounted Figure 10 To change the height position do the following 3 1 Remove the yoke locking knobs washers and hex bolts
9. rent lenses used in the n oo p UN a Source Four are not interchangeable s oo 1 B oo p mM o When installing a new lens refer to the illustration below for proper placement Also remember to have Excel DRE the lens color designator dot facing JE jJ oo the color frame B oH n a oo a 36 6x9 50 4 5x6 Dotless Yellow dot gt Figure 1 Source Four User Manual 1 Installing or replacing the HPL lamp A lamp must be installed before you use the fixture Note Verify that the HPL lamp you intend to install is suitable for your facility s voltage 115 120 230 and 240 volt HPL lamps are available See the above table Operating HPL lamps above their rated voltage reduces lamp life and can cause premature lamp failure Replace the lamp if it becomes damaged or thermally deformed WARNING Let the lamp cool before replacing 1 Disconnect power to the Source Four before installing the lamp 2 Loosen the knurled bolt on the back of the lamp housing and pull the housing out 3 Holding it by the base remove the HPL lamp from its box Note 7o avoid premature lamp failure do not touch the lamp glass If you do clean it carefully with rubbing alcohol and a clean lint free cloth before operation 4 Line up the flat sides of the lamp base with the retention brackets on either side of the socket as show in Figure 2 5 Push down on the lamp base until the lamp seats f
10. wer Ill e Enterprise Square e 9 Sheung Yuet Road Kowloon Bay e Hong Kong Tel 852 2799 1220 e Fax 4852 2799 9325 World Wide Web http www etcconnect com Email mail etcconnect com Specifications subject to change Source Four is protected by US patent numbers 5 345 371 5 446 637 5 268 613 and 5 544 029 Japanese Patent 2 501 772 US and International Patents Pending 7060M1001 Copyright 1999 Revised 12 99
Download Pdf Manuals
Related Search