Home

Owner`s Manual - Yacht Supply Depot

Contents

1. 11 Manually Controlling the Antenna 18 Updating Satellite Frequency Data 19 Displaying the Calibration Score wesc 81 Displaying the Antenna Software Version 82 Displaying the Antenna Serial Number 83 TracVision M5 M7 User s Guide Appendix A Advanced Settings and Functions Data Output Settings Overview This section explains how to modify the GyroTrac sensor s data output settings The TracVision system s GyroTrac sensor transmits up to five selectable message types simultaneously to external navigation devices connected to the ADCU One output port is dedicated to the sine cosine signal format Three serial ports allow outputs of NMEA 0183 KVH RS 422 and Cetrek proprietary signal formats Each of these message formats are described in the following sections Sine Cosine Data Output The TracVision system s GyroTrac sensor can be configured to provide either 3 wire or 4 wire sine cosine output but not both The sine cosine output is commonly used in ComNav Robertson and other autopilot systems TIP The B amp G 4 wire sine cosine output also known as the differential sine cosine is a substitute of the Halcyon compass output The reference voltage should be set to 3 5 volts NOTE The maximum current that can be drawn from the sine cosine output is 10 mA Sin
2. Compass Yes Next Return Select Next as required then select Yes Pitch Roll amp Yaw Rate of Turn Les Next Return Latitude Longitude Yes D Next Return Antenna display Yes QNext Return TracVision M5 M7 User s Guide Chapter 2 Operation Product Care Please consider the following antenna care guidelines for maintaining peak performance Periodically wash the exterior of the antenna dome with fresh water and mild detergent Avoid harsh cleansers and volatile solvents such as acetone and do not spray the dome directly with high pressure water If you wish to paint the dome use only non metallic automotive paint without a primer coat Any paint that contains metal will block satellite signals and impair reception im TracVision M5 M7 User s Guide Chapter 3 Settings 3 Settings This chapter contains information on system settings and how to modify them using the ADCU Contents Manually Setting Latitude and Longitude 33 Setting the LNB Skew Angle Linear Versions Only 34 Connecting d o ON m 40 DISH 1000 SERIO nra a treu tease 42 Dual Sat or Single Satellite Setups 46 European Tri Sat Mode Setup 52 Setting Instant On Mode eene 55 Setting Sleep Mode inner eate tois 56 Adjusting Display Brightness eese 57 Restarting t
3. Lr TracVision M5 M7 User s Guide Chapter 3 Settings Setting the LNB Skew Angle Linear Versions Only To optimize satellite signal reception you need to adjust the skew angle on the LNB whenever you change your geographic location or change which satellites are set up for tracking IMPORTANT If an active GPS is not connected be sure to enter your latitude and longitude manually before performing this procedure see Manually Setting Latitude and Longitude on page 33 TIP For information on how skew works see Circular and Linear Versions on page 9 TracVision M5 M7 User s Guide Chapter 3 Settings Determining the Skew Angle Use the flowchart in Figure 3 2 to determine the skew angle of the currently selected satellite using the ADCU NOTE If you wish to determine the average skew for two or three satellites determine the skew angle for each satellite by performing the procedure below then divide by the number of installed satellites TIP Sky Mexico subscribers can also refer to Figure 1 5 on page 10 for approximate skew settings for the PAS 9 satellite Figure 3 2 Determining the Skew Angle Using the ADCU lt Default Display gt Menu Setup display type Enter Next Return Select Next until Get antenna status is displayed Get antenna status nteD Next Return Then select Yes to confirm your selection Get system error Yes Next Retu
4. If you do not have a GPS connected to the ADCU you need to enter your vessel s latitude and longitude into the system Use the flowchart in Figure 3 23 to manually set the latitude and longitude values TIP For your convenience you can determine your approximate latitude and longitude using the Position Grids provided in Appendix E on page 107 Figure 3 23 Setting Latitude and Longitude Manually Default Display Menu Setup display type Enter Next Return Select Next until Control antenna is displayed Control antenna nteD Next Return Then select Yes to confirm your selection Man control antenna Press or to toggle each digit to the desired value then press Enter to accept each digit Longitude HEHE EnteD C Jj Latitude N Longitude IHHEE Set Lat Long Yes Next Return Select Next until Restart antenna is displayed Yes Next Return Restart antenna Yes gt Next Return Oog Antenna restarted Set Lat Long Yes Next Return O Press or to toggle each digit to the desired value then press Enter to accept each digit Latitude THEN Step 3 Adjust the LNB Skew Angle Now that you have installed the desired Tri Sat group you need to adjust the antenna s LNB skew angle to optimize signal reception Follow the instructions in Setting the LNB Skew Angle Linear Versio
5. Satellite Location Satellite Installation Name 26 0 E Arabsat ARABSAT 19 2 E Astra 1 ASTRA1 282 E Astra 2N ASTRA2N 282 E Astra 2S ASTRA2S 70 E Eutelsat W3A EUTEL W3A 30 00 W Hispasat HISPASAT 13 0 E Hotbird HOTBIRD 13 0 E Hotbird WB HOTBIRDWB 7 0 W Nilesat NILESAT 160 0 E Optus D1 OPTUS_D1 156 0 E Optus C1 OPTUS C1 58 0 W Pas 9 PAS_9 110 5 E Sinosat 1 SINOSAT 5 0 E Sirius SIRIUS 0 8 W Thor THOR 42 0 E Turksat 1C TURKSATIC NOTE Reception of this satellite requires special hardware Please contact your local KVH authorized dealer distributor or KVH Technical Support for details NOTE If you wish to only track one of the satellites listed above type NONE to substitute the second satellite For example to install only the Astra 1 satellite type SATINSTALL ASTRA1 NONE TracVision M5 M7 User s Guide Chapter 3 Settings Step 2 Configure the TracVision System Now you need to configure the TracVision system to track your selected satellites Use the flowchart in Figure 3 17 to configure your selected satellite s TIP For your convenience you can determine your approximate latitude and longitude using the Position Grids provided in Appendix E on page 107 Figure 3 17 Dual Sat or Single Satellite Setup Default Display Installing sats Menu Please wait lt SAT NAME1 gt and Setup display type lt SAT NAME2 gt i 11 Enter Next Return s instalted Select Nex
6. GyroTrac Sensor Grounding Block M cad d Circular Sky Mexico Systems Only Receiver 1 Controls satellite selection Receiver 2 969 999 UJ A zi TracVision M5 M7 User s Guide Appendix C Receiver Wiring Diagrams Wiring Diagram for Three or Four Receivers Circular Versions Vessel Power 12 VDO O TE D R c le m c 2 o E o gt E 5 D E o RF1 I I I I I I GyroTrac Vessel Power Sensor 12 VDC ESI L1 sg Grounding B Block Vessel AC Ground e Receiver 4 Power Satellite In Rx3 Receiver 2 Hil fj e Receiver 1 d rJ le HE m o0007 wWo NOTE Only the Eagle Aspen multiswitch KVH Part 472 0310 is approved for this configuration y S P pp 8 100 TracVision M5 M7 User s Guide Appendix C Receiver Wiring Diagrams Wiring Diagram for Three or Four Receivers Linear Quad output Versions Vessel Power 12 VDC D TI d9 em oO o em 2 o E o gt jmd e ru o Kj wo
7. TracVision M5 M7 User s Guide Appendix A Advanced Settings and Functions 5 Use the flowchart in Figure A 5 to scan the frequency data of the selected satellites TIP Scanning satellite frequencies might take up to 10 minutes Figure A 5 Scanning Frequency Data Default Display Menu Setup display type Enter Next Return Select Next until Control antenna is displayed Control antenna amp nteD Next Return Then select Yes to confirm your selection Man control antenna Yes Next Return Select Next until Sat frequency scan is displayed Sat frequency scan Yes Next Return Select or as required then select Enter valid range is 01000 39999 kilosymbols per second CD Ert GD Select or as required then select Enter valid codes are 1 2 2 3 3 4 5 6 6 7 and 7 8 Set FEC Code Scan frequencies Please wait Update frequency Updating frequency Please wait Restart antenna Yes gt No TracVision M5 M7 User s Guide Appendix A Advanced Settings and Functions Displaying the Calibration Score Use the flowchart in Figure A 6 to display the calibration score For information on interpreting the calibration score see Interpreting the Calibration Score on page 92 IMPORTANT If the system is currently configured to use an external compass you must set the TracVision system
8. DIRECTV DISH ExpressVu D12 311 4100 D11 3100 D10 High definition receivers DIRECTV DISH ExpressVu HD not 211k 6100 supported 211 KVH Technical Support at 1 401 847 3327 TracVision M5 M7 User s Guide Chapter 2 Operation DISH Network ExpressVu Receiver Configuration If your TracVision M5 M7 system is set up for DISH Network or ExpressVu service your receiver s should have also been configured during installation In most cases you do not need to reconfigure your receiver s However Figure 2 20 lists special scenarios that require DISH Network ExpressVu receiver configuration Figure 2 20 Receiver Configuration Requirements Receiver Configuration is Required When e DISH 1000 only You change satellite coverage areas see Figure 2 5 on page 15 e You add a receiver e You have reconfigured a receiver for home use If you need to configure a receiver s for DISH Network ExpressVu service follow the instructions for your selected service type in Chapter 3 Settings on page 31 Linear Receiver Configuration If the TracVision system does not include a multiswitch you can configure the receiver s to enable automatic satellite switching TracVision systems with a multiswitch installed require switching satellites manually using the ADCU which does not require receiver configuration To configure the receivers for automatic switching set up the satellites in the receiver in the sa
9. ie E a o em um Vessel Power 12 VDC GyroTrac Sensor Receiver 1 Satellite S 997090 1t amp Controls satellite w selection Receiver 2 Jj Receiver 3 Satellite In elu C a HHT Satellite In i 6967000 ELT E zs lolo gt Receiver 4 Satellite In li a 9 Of NOTE If you wish to connect more than four receivers you will need to install an active powered multiswitch such as Spaun model SMS5602 NF You can purchase this multiswitch from KVH KVH Part 19 0413 101 TracVision M5 M7 User s Guide Appendix D ADCU Wiring Diagrams Appendix D ADCU Wiring Diagrams This appendix provides ADCU wiring diagrams for both required and optional equipment For installation instructions refer to the Installation Guide Contents ADCU Wiring Diagram Required 105 ADCU Wiring Diagram Optional Equipment 106 i 103 TracVision M5 M7 User s Guide Appendix D ADCU Wiring Diagrams ADCU Wiring Diagram Required Antenna Data Green White White Green Blue White White Blue Brown White White Brown Orange White White Orange Gray White 777 7 White Gray Yellow Lab
10. eeeeen 110 107 European Position Grid TracVision M5 M7 User s Guide Appendix E Position Grids If you wish to determine your approximate latitude and longitude use the position grid and table in Figure E 1 Figure E 1 Approximate Latitude and Longitude Grid Latitude Longitude 1 67 N 7 W 2 67 N rE 3 67 N 22 E 4 65 N 45 E 5 63 N 7 W 6 63 N TUE 7 63 N 22 E 8 57 N 7 W 9 57 N LE 10 57 N 22 E 11 55 N 40 E 12 53 N 7 W 13 53 N 7 E 14 50 N 22 E 15 47 N 7 W 16 47 N 7 E 17 43 N 7 W 18 43 N TE 19 43 N 22 E 20 43 N 37 E 21 36 N 7 W 22 36 N 7 E 23 36 N 22 E 24 36 N 37 E i 109 TracVision M5 M7 User s Guide Appendix E Position Grids North American Position Grid If you wish to determine your approximate latitude and longitude use the position grid and table in Figure E 2 Figure E 2 Approximate Latitude and Longitude Grid Latitude Longitude 1 55 N 125 W 2 55 N 110 W 3 55 N 90 W 4 55 N 70 W 5 55 N 55 W 6 45 N 125 W 7 45 N 110 W 8 45 N 90 W 9 45 N 70 W 10 45 N 50 W 11 40 N 125 W 12 40 N 110 W 13 40 N 90 W 14 40 N 70 W 15 32 N 125 W 16 32 N 110 W 17 32 N 90 W 18 32 N 75 W 19 27 N
11. you need to subtract 180 to get the equivalent negative skew angle and set the LNB to that angle instead For example if the skew angle is determined to be 30 set the skew to 150 IMPORTANT Be sure to keep the LNB fully inserted in the choke feed to ensure optimum performance Figure 3 6 TracVision M5 LNB Skew Angle Adjustment Choke Feed Negative Positive k Skews 0 Skew Skews TracVision M5 M7 User s Guide Chapter 3 Settings 4b TracVision M7 Only Adjust the LNB clockwise or counter clockwise until the skew arrow on the LNB points to the skew angle that you determined earlier IMPORTANT Be sure to keep the LNB fully inserted in the choke feed to ensure optimum performance Figure 3 7 TracVision M7 LNB Skew Angle Adjustment Choke Feed Negative I Positive Skews I Skews 0 Skew 5 Tighten the two M4 socket set screws to secure the LNB in place Apply 9 in lbs 1 Nm of torque if possible 6 Reinstall the radome 7 Restore power to the TracVision system TracVision M5 M7 User s Guide Chapter 3 Settings Connecting a PC Follow the instructions below if you need to connect a PC to the TracVision M5 M7 system This procedure requires a PC with Windows HyperTerminal or equivalent and a serial data cable TIP If you are a KVH authorized technician you can use the KVH Flash Update Wizard instead of Hy
12. ADCU see Figure 2 17 and Figure 2 18 IMPORTANT Pressing a button on the ADCU to manually switch satellites disables DiSEqC monitoring for automatic switching The antenna must be turned off then back on to restore DiSEqC communications Figure 2 17 Manual Satellite Switching Receiver ADCU Controls Quad output LNB Version Shown GyroTrac Sensor Buttons used to switch satellites All Receivers Changes channels on current satellite Wf oum om m o m m m m m x m mm m Figure 2 18 Manually Switching Between Satellites ADCU Displays Three Satellites Installed Two Satellites Installed Tracking Sat AD Tracking Sat A Sat B Menu KSat C amp Sat B Menu Press Press Press for Sat B for Sat C for Sat B Selected Selected Satellite Satellite 23 TracVision M5 M7 User s Guide Chapter 2 Operation Receiver Requirements This section lists U S and Canadian circular receiver models that are compatible with the TracVision M5 M7 system and explains linear and circular receiver setup requirements To ensure compatibility with your TracVision M5 M7 system be sure to use a KVH validated receiver for your selected service type see Figure 2 19 Circular Receiver Compatibility Figure 2 19 KVH Validated U S and Canadian Receivers Standard definition receivers NOTE For information on connecting different receiver models contact
13. Compass screen displays the magnetic heading value see Turning the System On Off on page 14 for details on GPS initialization Figure 2 23 Compass Screen with Magnetic Heading Magnetic Heading HHH H When GPS is connected and is properly initialized the Compass screen displays both magnetic heading and true heading values Figure 2 24 Compass Screen with Magnetic and True Heading Mag HDG True HDG HHH H HHH TracVision M5 M7 User s Guide Chapter 2 Operation Pitch Roll and Yaw The pitch roll and yaw display type displays the vessel s pitch roll and yaw values Figure 2 25 Pitch Roll and Yaw Screen Pitch Roll Yaw H H Rate of Turn The rate of turn display type displays the vessel s magnetic heading and rate of turn values Figure 2 26 Rate of Turn Screen Mag HDG Rate sec HHHH HHHH Latitude Longitude When GPS is connected and is properly initialized the Latitude Longitude screen displays the vessel s latitude and longitude values see Turning the System On Off on page 14 for details on GPS initialization Figure 2 27 Latitude Longitude Screen Latitude HEN Longitude E UN TracVision M5 M7 User s Guide Chapter 2 Operation Changing Display Types Use the flowchart in Figure 2 28 if you wish to change the display type Figure 2 28 Changing Display Types Default Display Cenu Setup display type nteD Next Return
14. Figure A 3 to modify the heading reference source Figure A 3 Setting the Heading Reference Source Default Display Menu Setup display type Enter Next Return Select Next until Setup configuration is displayed Setup configuration nteD Next Return Then select Yes to confirm your selection Set brightness Yes Next gt Return Set heading int ext Next Return Reference Internal Int CEnted CExt Select Int for internal or Ext for external then select Enter TracVision M5 M7 User s Guide Appendix A Advanced Settings and Functions Manually Controlling the Antenna Use the flowchart in Figure A 4 if you wish to manually control the antenna NOTE If you are performing this procedure as part of a satellite frequency scan update procedure be sure to select NO at the Make Antenna Track screen TIP Once you have finished positioning the antenna the system will revert to automatic control Figure A 4 Manually Controlling the Antenna lt Default Display gt Menu Setup display type Enter Next Return Select Next until Control antenna is displayed Control antenna nteD Next Return Then select Yes to confirm your selection Man control antenna Next Return Finding limit switch Please wait Select or as required then select Enter Make antenna track No Cancel TracVisi
15. Position Group Name Satellites Position Hotbird WB A Europe WB Astra 1 B Astra 25 C Hotbird A Europe Astra 1 B Astra 25 C Hotbird WB A Scandinavia Sirius B Thor C NOTE To enable automatic switching the receiver must be set up to match the TracVision system s satellite position settings A B or C Refer to Linear Receiver Configuration on page 25 for more information TracVision M5 M7 User s Guide Chapter 3 Settings Step 1 Configure the TracVision System Follow the steps below to set up the TracVision system for your desired European Tri Sat Mode You will enter PC commands into the HyperTerminal window An example is provided in Figure 3 22 1 Connect a PC to the maintenance port as described in Connecting a PC on page 40 You will enter the following PC commands into the HyperTerminal window 2 Type HALT then press Enter 3 Usethe table below to enter the following SATINSTALL command then press Enter For Group Type Europe WB SATINSTALL TRISAT EWB Europe SATINSTALL TRISAT EUR Scandinavia SATINSTALL TRISAT SCN 4 Type ZAP then press Enter to restart the antenna Wait one minute for system startup Figure 3 22 Example European Tri Sat Mode Europe WB Group HALT SATINSTALL TRISAT EWB ZAP TracVision M5 M7 User s Guide Chapter 3 Settings Step 2 Update Latitude and Longitude Data if necessary
16. components 3 5 TRAGVISION KVH Antenna Unit The antenna unit houses the antenna positioning mechanism LNB low noise block and control elements within a radome Weathertight connectors join the power signal and control cabling from the belowdecks units GyroTrac Sensor The GyroTrac digital magnetic compass sensor provides a three axis gyro stabilized heading reference allowing superior open water performance in any sea condition It is also compliant with the IP67 standard the unit is waterproof to a depth of 1 meter ADCU Advanced Digital Control Unit The ADCU is the system s user interface providing access to the system and its functions through an LCD with three buttons The ADCU also serves as the system s junction box allowing the system to interface with the GyroTrac sensor and supply and receive data to from the TracVision M5 M7 and other onboard equipment i TracVision M5 M7 User s Guide Chapter 1 Introduction System Features Your TracVision M5 M7 uses integrated DVB technology to quickly acquire and track the correct satellite switch between your selected satellites and send TV signals to the receiver In motion Tracking The TracVision system uses a state of the art actively stabilized antenna Once the satellite is acquired the antenna s internal gyros continuously measure the heading pitch and roll of your vessel and send commands to the an
17. configuration see Figure 3 13 and Figure 3 14 If your values do not match turn off the antenna then turn it back on and repeat Steps 4 8 Figure 3 13 DISH 1000 61 Second Check Switch Results on TV Screen Port 1 2 3 Satellite 119 110 61 Trans OK OK OK Status Reception Verified Switch SW64 Figure 3 14 DISH 1000 129 Second Check Switch Results on TV Screen Port 1 2 3 Satellite 119 110 129 Trans OK OK OK Status Reception Verified Switch SW64 10 Exit the menu and allow the receiver to download the program guide NOTE You do not need to perform this procedure again unless you add another receiver you reconfigure a receiver s for home use or you move to a different DISH 1000 satellite coverage area see DISH 1000 Required for TurboHD Service on page 15 EB TracVision M5 M7 User s Guide Chapter 3 Settings Dual Sat or Single Satellite Setups The following instructions explain how to configure the TracVision system to track one or two satellites of your choice from the antenna s satellite library For operation instructions refer to Operation on page 11 IMPORTANT Be sure to stop the vessel in a blockage free area before performing this procedure Excessive motion or satellite blockage can prevent proper configuration NOTE Be sure to only install satellites that your TracVision M5 M7 system c
18. control to change channels on the currently selected satellite If you need to switch satellites simply use the buttons on the front of the ADCU see Figure 2 13 and Figure 2 14 You can use the receivers remote controls to switch between the channels on the currently selected satellite Figure 2 13 Dual Sat Manual Mode Receiver ADCU Controls GyroTrac Sensor Buttons used to switch satellites All Receivers Changes channels on current satellite poer Press for Selected Sat B Satellite TracVision M5 M7 User s Guide Chapter 2 Operation Changing Channels and Switching Between Satellites Linear Versions During installation your TracVision system should have been set up to track the satellite s of your choice and the channel guides for your selected satellite service should have been downloaded Since some channels might be located on another satellite changing channels might require switching between satellites Switching satellites occurs automatically with most TracVision system configurations However if the TracVision system includes a multiswitch manual satellite switching is required NOTE To enable automatic switching the receiver must be properly configured see Linear Receiver Configuration on page 25 for more information TracVision M5 M7 User s Guide Chapter 2 Operation Automatic Satellite Switching The TracVision system can switch between satellites
19. displayed Set Gyro offsets Setup data outputs Yes Next Return Enter Next Return Then select Yes to confirm your selection Setup configuration Next Return Then select Yes to confirm your selection Set offset Pitch eturn Yes Next R Select or as required then select Enter Set Pitch Set offset Roll Return Select or as required then select Enter Set Roll Set offset Yaw Yes Next Return Select or as required then select Enter Set Yaw LER TracVision M5 M7 User s Guide Appendix C Receiver Wiring Diagrams Appendix C Receiver Wiring Diagrams This appendix provides receiver wiring diagrams for basic configurations Wiring diagrams vary according to the number of receivers installed and the TracVision system configuration circular linear and dual quad output For installation instructions refer to the Installation Guide Contents Wiring Diagram for One or Two Receivers 99 Wiring Diagram for Three or Four Receivers Circular Ver SIS dv bc d te 100 Wiring Diagram for Three or Four Receivers Linear Quad output Versions esee 101 TracVision M5 M7 User s Guide Appendix C Receiver Wiring Diagrams Wiring Diagram for One or Two Receivers Vessel Power 12 VDC Vessel Power 12 VDC
20. system for DISH 500 or ExpressVu use For operation instructions and additional information on DISH modes refer to Changing Channels and Switching Between Satellites Circular Versions on page 15 NOTE If you are connecting multiple receivers repeat this process for each additional receiver You will need to connect each receiver one at a time to the RF1 cable and perform the steps below Then once you have completed this process for each receiver you can reconnect them as desired 1 Ensure the receiver you wish to configure is connected to the TracVision system s RF1 cable 2 Apply operating power to the TracVision system Then turn on the TV s and receiver s Wait until the tracking screen for your selected configuration is displayed Figure 3 18 Tracking Screen Tracking lt Sat A gt lt Sat B gt Menu 3 Using the receiver s remote go to the Point Dish Signal Strength screen press MENU 6 1 1 on most models 4 Choose Check Switch then press SELECT 5 Choose Test then press SELECT TracVision M5 M7 User s Guide Chapter 3 Settings 6 Wait at least 15 minutes before proceeding Disregard messages on the TV stating the test is complete you must wait 15 minutes before proceeding IMPORTANT Please be patient The Check Switch test takes approximately 15 minutes to complete Disregard any messages on the TV stating the test is complete the antenna must perform addition
21. to the Troubleshooting chapter to help identify the cause of a system problem Notifications Used in this Manual This manual uses the following notifications to call attention to important information A CAUTION This is a danger warning or caution notice Be sure to read these carefully to avoid injury IMPORTANT This is an important notice Be sure to read these carefully to ensure proper operation and configuration of your TracVision system NOTE Notes contain useful information about system settings TIP Tips contain helpful information allowing you to get the most out of your TracVision system TracVision M5 M7 User s Guide Chapter 1 Introduction Typographical Conventions This manual uses the following typographical conventions Text Example Description lt SAT NAME gt Text in brackets or the pound sign indicates a HHH variable portion of the Advanced Digital Control Unit ADCU display HALT Bold text in capital letters indicates a command to be entered via a PC X Bold text in italicized capital letters indicates a variable portion of a command to be entered via a PC ADCU Advanced Digital Control Unit Interface Conventions When instructions indicate to select a specific ADCU menu option press the ADCU button located directly beneath the menu option Figure 1 1 Example of ADCU Menu Option and Corresponding Button Compass Yes Re
22. to use an internal heading reference before performing this procedure See Setting the Heading Reference Source on page 77 for more information Figure A 6 Displaying the Calibration Score Default Display Menu Setup display type Enter Next Return Select Next until Control Compass is displayed Control compass Next Return Then select Yes to confirm your selection Set AutoCal On Off Yes Next Return Read Cal score Yes Next Return Acc MagEnv Cal CAL lt GHHHt Press center button to exit TracVision M5 M7 User s Guide Appendix A Advanced Settings and Functions Displaying the Antenna Software Version Use the flowchart in Figure A 7 if you wish to display the antenna software version Figure A 7 Displaying the Antenna Software Version Default Display Menu Setup display type Enter Next Return Select Next until Get antenna status is displayed Get antenna status nteD Next Return Then select Yes to confirm your selection Get system error Yes Next Return Get version Yes Next Return Antenna type Antenna ver TracVision M5 M7 User s Guide Appendix A Advanced Settings and Functions Displaying the Antenna Serial Number Use flowchart in Figure A 8 if you wish to display the antenna serial number Fig
23. 83 W 20 27 N 78 W 110 KIVIHI KVH Industries Inc KVH Europe A S 50 Enterprise Center Middletown RI 02842 5279 U S A Kokkedal Industripark 2B 2980 Kokkedal Denmark Phone 1 401 847 3327 Fax 1 401 849 0045 Phone 45 45 160 180 Fax 45 45 160 181 E mail info kvh com Internet www kvh com E mail info kvh dk Internet www kvh com Copyright 2006 KVH Industries Inc KVH and TracVision are registered trademarks of KVH Industries Inc
24. Available Satellites Available Satellites Buttons Not Used Buttons Not Used Selected Selected Satellite Satellite TracVision M5 M7 User s Guide Chapter 2 Operation DISH 1000 Manual Mode Required for Three or More Receivers Since multiswitches interfere with communications between the receivers and the antenna the system must be set up in Manual mode when three or more receivers are installed When Manual mode is enabled you can switch between your selected satellites using the buttons on the front of the ADCU see Figure 2 8 and Figure 2 9 You can use the receivers remote controls to switch between the channels on the currently selected satellite Figure 2 8 DISH 1000 Manual Mode Receiver ADCU Controls GyroTrac Sensor Buttons used to switch satellites Grounding e Block All Receivers Changes channels on current satellite III for 110 for 61 for 110 for 129 Selected Selected Satellite Satellite TracVision M5 M7 User s Guide Chapter 2 Operation Dual Sat Mode DISH 500 ExpressVu DIRECTV and Custom Dual Sat Setups Dual Sat Mode is used with several service configurations Figure 2 10 lists each Dual Sat service configuration the satellites tracked for each service and the available satellite switching modes Figure 2 10 Dual Sat Modes Available Service Satellites Tracked Switching Mode s DIRECTV DIRECTV 101 and 119 Auto or Manual DIS
25. H 500 DISH 119 and 110 Auto or Manual ExpressVu ExpressVu 91 and 82 Auto or Manual Custom Selected by user Manual TracVision M5 M7 User s Guide Chapter 2 Operation Dual Sat Automatic Mode Preferred Mode for One or Two Receivers The antenna switches between satellites automatically while you change channels using the primary receiver s remote control The primary receiver is the receiver connected to the antenna s RF1 cable see Figure 2 11 and Figure 2 12 If an optional secondary receiver is connected you can use its remote control to switch between the channels on the currently selected satellite NOTE Custom Dual Sat configurations must use Manual mode Figure 2 11 Dual Sat Automatic Mode Receiver Controls GyroTrac Sensor Grounding Primary Receiver Automatically switches satellites channels Secondary Receiver optional Changes channels on current satellite Available Satellite Button Not Used Selected Satellite i Chapter 2 Operation TracVision M5 M7 User s Guide Dual Sat Manual Mode Required for Three or More Receivers and All Custom Dual Sat Setups Circular TracVision M5 M7 systems with three or more receivers require the use of a multiswitch Since multiswitches interfere with communications between the receivers and the antenna the system must be set up in Manual mode When manual mode is enabled you can use the receiver s remote
26. M7 User s Guide Chapter 4 Troubleshooting Satellite Coverage Issue Television satellites are located in fixed positions above the Earth s equator and beam TV signals down to certain regions of the planet not worldwide To receive TV signals from a satellite you must be located within that satellite s unique coverage area TIP For your convenience KVH provides links to several websites that offer satellite coverage information Simply visit our website at www kvh coml footprint Figure 4 2 Location and Coverage Area of DIRECTV 101 Satellite e Equator Satellite Signal Blocked Since TV satellites are located above the equator the TracVision antenna must have a clear view of the sky to receive satellite TV signals Anything that stands between the antenna and the satellite can block the signal resulting in lost reception Common causes of blockage include boat masts trees buildings and bridges Heavy rain ice or snow might also temporarily interrupt satellite signals Figure 4 3 Example of Satellite Blockage Blocked p li i NOS M ue f dl Do D X TracVision M5 M7 User s Guide Chapter 4 Troubleshooting Radar Interference The TracVision M5 M7 antenna must be kept out of line with nearby radars as their energy levels might overload the antenna s front end circuits Refer to the TracVision M5 M7 Installation Guide for de
27. S S X TracVision M5 M7 User s Guide Chapter 4 Troubleshooting Causes and Remedies for Operational Issues This section addresses the most common operational issues that can affect the performance of the TracVision M5 M7 system If your TracVision system requires service you can visit any KVH authorized dealer or distributor for assistance To find a KVH authorized dealer near you visit www kvh com wheretogetservice Receiver Fault or Improper Receiver Configuration Receiver Fault Your satellite TV receiver might be set up incorrectly or defective First check the receiver s configuration to ensure it is set up for the desired programming In the case of a faulty receiver refer to your selected receiver s user manual for service and warranty information Improper Receiver Configuration Linear Versions Only To enable automatic satellite switching the receiver s must be set up for the same satellites and in the same order they are set up in the antenna NOTE Linear TracVision systems with a multiswitch installed require manually switching satellites using the ADCU which does not require receiver configuration TracVision Satellite Receiver Satellite DiSEqC Setting Satellite A Alternative lor A DiSEqC 1 Satellite B Alternative 2 or B DiSEgC 2 Satellite C Alternative 3orC DiSEqC 3 NOTE Only European Tri Sat configurations track three satellites TracVision M5
28. TRACVISION e B KVH INDUSTRIES TracVision M5 M7 EY IO EE CHI Configuration TRADViISiOG a C o p a o n LC e 2 e i I TracVision M5 M7 User s Guide TracVision M5 M7 GyroTrac Configuration User s Guide This user s guide provides all of the basic information you need to operate set up and troubleshoot the TracVision M5 M7 satellite TV antenna system For detailed installation information please refer to the TracVision M5 M7 Installation Guide aa TRACVISiO KVH EE TRACVISIO Pass kvi Please direct questions comments or suggestions to KVH Industries Inc KVH Europe A S 50 Enterprise Center Kokkedal Industripark 2B Middletown RI 02842 5279 USA 2980 Kokkedal Denmark Tel 1 401 847 3327 Tel 45 45 160 180 Fax 1 401 849 0045 Fax 45 45 160 181 E mail info kvh com E mail info kvh dk Internet www kvh com Internet www kvh com If you have any comments regarding this manual please e mail them to manuals kvh com Your input is greatly appreciated OMe KVH Part 54 0419 01 Rev D KVHVl j ISO 2007 2009 KVH Industries Inc All rights reserved NASDAQ s 9001 U S Patents Pending i i TracVision and KVH are registered trademarks of KVH Industries Inc The unique light colored dome with dark contrasting base is a registered trademark of KVH Industries Inc DVB Digital Video Broadcasting is a registered trademark of the DVB Projec
29. Wiring If the system has been improperly wired the antenna will not operate correctly Refer to the wiring diagrams provided in Appendix C on page 97 You can also refer to the TracVision M5 M7 Installation Guide for complete system wiring information or visit any KVH authorized dealer or distributor for assistance To find a KVH authorized dealer near you visit www kvh com wheretogetservice im TracVision M5 M7 User s Guide Chapter 4 Troubleshooting Loose RF Connectors KVH recommends that you periodically check the system s cable connections A loose RF connector can reduce signal quality or prevent automatic satellite switching using the receiver s remote control Refer to the TracVision M5 M7 Installation Guide for complete system wiring information or visit any KVH authorized dealer or distributor for assistance To find a KVH authorized dealer near you visit www kvh comlwheretogetservice Type of Multiswitch Used If your TracVision system s configuration requires a multiswitch an active powered multiswitch must be used to ensure proper antenna performance Refer to the wiring diagrams in Appendix C on page 97 for detailed information Cable Unwrap If your vessel makes several consecutive circles in the same direction the antenna will rotate 720 before reaching the end of its internal cable If this occurs the system will automatically unwrap the cable by quickly rotating the antenna dish in the o
30. al operations before proceeding 7 After waiting 15 minutes repeat Steps 3 5 to runa second Check Switch test NOTE Each Check Switch test takes approximately 15 minutes 8 Verify the values on your TV match those required for your selected configuration see Figures 3 19 and 3 20 If your values do not match turn off the antenna then turn it back on and repeat Steps 4 7 Figure 3 19 DISH 500 Second Check Switch Results on TV Screen Port 1 1 2 2 Satellite 119 119 110 110 Trans Odd Even Odd Even Status Reception Verified Switch SW42 Figure 3 20 ExpressVu Second Check Switch Results on TV Screen Port 1 1 2 2 Satellite 91 91 82 82 Trans Odd Even Odd Even Status Reception Verified Switch SW21 9 Exit the menu and allow the receiver to download the program guide NOTE You do not need to perform this procedure again unless you add another receiver or you reconfigure a receiver for home use E TracVision M5 M7 User s Guide Chapter 3 Settings European Tri Sat Mode Setup This section explains how to configure the TracVision system to track three satellites within predefined linear satellite groups for European locations see Figure 3 21 For operation instructions refer to Changing Channels and Switching Between Satellites Linear Versions on page 21 Figure 3 21 European Tri Sat Groups Satellites TracVision
31. an track in your geographic location For your convenience KVH provides links to several websites that offer satellite coverage information Simply visit our website at www kvh comlfootprint TracVision M5 M7 User s Guide Chapter 3 Settings Step 1 Select Satellites You can select up to two satellites from either the circular satellite library see Figure 3 15 or the linear satellite library see Figure 3 16 on page 48 Figure 3 15 Circular Satellite Library Satellite Satellite Service Location Installation Name AsiaSat 4 1222 E ASIASAT 72 00 W DSS 72 101 0 W_ DSS 101 DIRECTV 110 00 W DSS 110 119 00 W DSS 119 DIRECTV Latin os gow GALAXY3CN America 61 5 W ECHO_61 DISH Network 110 0 W ECHO_110 119 0 W ECHO 119 129 0 W ECHO 129 91 0 W EXPRESSTV ExpressVu 82 0 W EXPRESSVU NOTE Reception of these satellites requires special hardware Please contact your local KVH authorized dealer or KVH Technical Support for details NOTE If you wish to track only one of the satellites listed above type NONE to substitute the second satellite For example ExpressVu subscribers who wish to track just the 91 satellite should type SATINSTALL EXPRESSTV NONE EM TracVision M5 M7 User s Guide Chapter 3 Settings Lr Figure 3 16 Linear Satellite Library
32. atellites Tracked DISH 1000 61 DISH 110 119 and 61 DISH 1000 129 DISH 110 119 and 129 During installation your TracVision system should have been set to the DISH 1000 configuration that best suits your geographic location see Figure 2 5 and local channels requirements If you change satellite coverage areas refer to DISH 1000 Setup on page 42 to change your DISH 1000 configuration Figure 2 5 Regional DISH 1000 Configuration Recommendations _ DISH 129 Satellite Recommended P DISH 61 Satellite Recommended 15 Chapter 2 Operation TracVision M5 M7 User s Guide DISH 1000 Automatic Mode Preferred for One or Two Receivers The antenna switches between satellites automatically as you change channels using the primary receiver s remote control The primary receiver is the receiver connected to the antenna s RF1 cable see Figure 2 6 and Figure 2 7 If an optional secondary receiver is connected you can use its remote control to switch between the channels on the currently selected satellite Figure 2 6 DISH 1000 Automatic Mode Receiver Controls GyroTrac Sensor 3 Grounding Block Automatically switches satellites channels Secondary Receiver optional Changes channels on current satellite Figure 2 7 DISH 1000 Automatic Mode ADCU Displays DISH 1000 61 DISH 1000 129 Tracking QISH 119 Tracking QISH 119 OR kmb wes Cm
33. automatically as long as the primary receiver is set up for DiSEqC communicatons and a multiswitch is not installed With DiSEqC set up the primary receiver sends satellite switching commands to the antenna as necessary when you change channels using the primary receiver s remote control The primary receiver is the receiver connected to the antenna s RF1 cable see Figure 2 15 If an optional secondary receiver is connected you can use its remote control to switch between the channels on the currently selected satellite Figure 2 15 Primary Secondary Receiver Control Dual output version shown GyroTrac Sensor Grounding Block ol Sky Mexico Systems Only Primary Receiver Automatically switches satellites channels Secondary Receiver optional Changes channels on current satellite Figure 2 16 Automatically Switching Between Satellites ADCU Display Three Satellites Installed Two Satellites Installed Tracking Sat AD Tracking Sat A Menu amp Sat C KSat B Menu Available Satellites Available Satellite Buttons Not Used Button Not Used Selected Selected Satellite Satellite TracVision M5 M7 User s Guide Chapter 2 Operation Manual Satellite Switching If the TracVision system includes a multiswitch you can use the receivers remote controls to change channels on the currently selected satellite If you need to switch satellites simply use the buttons on the front of the
34. core Be sure to verify that the calibration yielded acceptable results If the calibration did not yield acceptable results you will need to restart recalibration Displaying the Calibration Score Use the flowchart in Figure B 4 to display the calibration score Figure B 4 Displaying the Calibration Score Default Display enu Setup display type Enter Next Return Select Next until Control Compass is displayed Control compass nte2 Next Return Then select Yes to confirm your selection Set AutoCal On Off Yes Next Return Read Cal score Yes Next Return Acc MagEnv Cali CAL lt HHHH Press center button to exit J TracVision M5 M7 User s Guide Appendix B Recalibration Interpreting the Calibration Score Each calibration results in a calibration score that is stored in the system s memory The calibration score contains an accuracy rating a magnetic environment rating and the number of calibrations performed Figure B 5 Calibration Score Screen Acc MagEnv Cali CAL lt 1 GOOD 1 Accuracy Magnetic Calibration Rating Environment Number Rating Accuracy Rating The accuracy rating indicates the degree of accuracy the GyroTrac will provide based on the quality of the last calibration Figure B 6 lists five possible accuracy rating levels Figure B 6 Accuracy Rating Levels Accuracy Rati
35. e to the RF1 cable and perform the steps below Then once you have completed this process for each receiver you can reconnect them as desired IMPORTANT This procedure must be performed while the vessel is stopped in calm waters 1 Ensure the receiver you wish to configure is connected to the TracVision system s RF1 cable 2 Turnon the TV and receiver 3 Apply power to the TracVision system Wait until the tracking screen for your selected DISH 1000 configuration is displayed Figure 3 12 Tracking Screens Tracking DISH 119 DISH 1000 61 Mode Menu 61 Tracking DISH 119 DISH 1000 129 Mode Menu 129 4 Using the receiver s remote go to the Point Dish Signal Strength screen press MENU 6 1 1 on most models 5 Choose Check Switch then press SELECT 6 Choose Test then press SELECT 7 Wait at least 15 minutes before proceeding Disregard messages on the TV stating the test is complete you must wait 15 minutes before proceeding IMPORTANT Please be patient The Check Switch test takes approximately 15 minutes to complete Disregard any messages on the TV stating the test is complete the antenna must perform additional operations before proceeding TracVision M5 M7 User s Guide Chapter 3 Settings 8 After waiting 15 minutes repeat Steps 4 6 to runa second Check Switch test 9 Verify the values on your TV match those required for your selected DISH 1000
36. e Installation Guide you need to adjust the sensor offset values to compensate for variances when pitch roll and azimuth references cannot be met NOTE The maximum offset values for pitch and roll are 45 the maximum offset value for azimuth is 180 NOTE Pitch roll and yaw settings are determined by the GyroTrac sensor not external hardware Step 1 Zero All Offset Values Use the flowchart in Figure 3 on page 95 to enter zeros for all measurements Step 2 Record the Difference in Offset Values Now you need to record the difference in the offset values displayed Navigate to the Pitch Roll and Yaw display Then record the values displayed for pitch roll and yaw see Pitch Roll and Yaw on page 27 for more information Step 3 Enter Inverse Offset Values Use the flowchart in Figure 3 on page 95 to enter the inverse values for the measurements you recorded earlier positive becomes negative negative becomes positive An example of offset value compensation is provided in Figure B 8 Figure B 8 Example of Offset Compensation For Recorded Offset Enter Offset 10 0 10 0 12 6 12 6 TracVision M5 M7 User s Guide Appendix B Recalibration Figure 3 Setting Sensor Offset Values lt Default Display gt Menu Set brightness Yes Next Return Select Next spl gt until Set Gyro Setup E CY e offsets is aS psec
37. e cosine setup requires the following to be selected Magnetic or true heading Reference voltage valid range is 0 6 5 volts default value is 2 5 volts e Swing voltage valid range is 0 6 5 volts default value is 1 67 volts TracVision M5 M7 User s Guide Appendix A Advanced Settings and Functions Use the flowchart in Figure A 1 to modify the sine cosine data output settings or restore the original sine cosine settings NOTE If an active GPS connection is not detected Only Mag Available is displayed If the ADCU is receiving data from an external gyro all compass outputs are automatically configured as True North causing Only True Available to be displayed Figure A 1 Sine Cosine Data Output Settings Default Display Menu Setup display type Enter Next Return Setup data outputs nteD Next Return Then select Yes to confirm your selection Set sine cos levels Yes Next Return Select magnetic or true as required then select Enter Sine cosine is Mag as required then select TracVision M5 M7 User s Guide Appendix A Advanced Settings and Functions Serial Port Outputs Serial ports 1 and 2 can be individually programmed to output any of the message formats described in this section serial port 3 is disabled when a TracVision system is connected to the ADCU Up to four NMEA 0183 listening devices can be connected to each of the serial ports Serial por
38. e screen after system self testing is complete Figure 2 3 Tracking Satellite Screen Tracking Sat A Sat B Menu Sat C Available Satellites Selected Satellite Turning Off the System Follow the steps below to turn off your TracVision system 1 Remove operating power from the TracVision system 2 Turn off your satellite TV receiver and TV TracVision M5 M7 User s Guide Chapter 2 Operation Changing Channels and Switching Between Satellites Circular Versions During installation your TracVision system should have been set up to track the satellite s of your choice and the channel guides for your selected satellite service should have been downloaded Since some channels might be located on another satellite changing channels might require switching between satellites With most TracVision configurations satellite switching occurs automatically while you change channels using the primary receiver s remote control Find your selected service and configuration in the following sections for complete details TIP The primary receiver is the receiver connected to the antenna s RF1 connector DISH 1000 Required for TurboHD Service When the TracVision M5 M7 system is configured for DISH 1000 you can view the DISH HDTV programming for your geographic area You can configure the system for either DISH 1000 61 or DISH 1000 129 use Figure 2 4 DISH 1000 Configurations Configuration S
39. el Red Label Green Label Blue Label 1 L L Vessel Power GyroTrac Sensor Li 12 16 VDC Green White Ground In Black Orange White 12 VDC Power In Red i White Orange Blue White GyroTrac White Blue Sensor White Green A 105 TracVision M5 M7 User s Guide Appendix D ADCU Wiring Diagrams ADCU Wiring Diagram Optional Equipment TILL e Yellow Label Red Label Green Label Blue Label White Label 2 3 4 3 6 7 8 3 19 11 E 34 15 16 17 18 19 20 2 2 25 26 27 28 29 30 3 3r 35 34 36 36 BEBHEENEENNNEEE HEEHHERERE ENHEERHERBEENEERE uM n M X e eod EE Serial Port 1 Display Power TX1A TXIBG s seee58 Ground Sine Cosine Ground 1 Ref Voltage Cosine inverted 1 Cosine Sine inverted Sine Duplicate Serial Port 1 Ground scescs 52 gt i TX1B TX1A KVH Display Power GPS Ship s Gyro GPS B or HDG B GPS A or HDG A l Serial Port 2 Ground TX2A 106 TracVision M5 M7 User s Guide Appendix E Position Grids Appendix E Position Grids This appendix contains European and North American position grids for determining your approximate latitude and longitude Contents European Position Grid side tit 109 North American Position Grid
40. ellite Equator In addition since TV satellites are located above the equator the TracVision antenna must have a clear view of the sky to receive satellite TV signals Anything that stands between the antenna and the satellite can block the signal resulting in lost reception Common causes of blockage include boat masts trees buildings and bridges Heavy rain ice or snow might also temporarily interrupt satellite signals Figure 2 2 Example of Satellite Blockage dq Q IN Il ill m pasii M ft Blocked Dann pat TracVision M5 M7 User s Guide Chapter 2 Operation Turning the System On Off Since power to the TracVision system is controlled by the vessel power you can turn the system on or off by applying removing vessel power Turning On the System Follow the steps below to turn on your TracVision system IMPORTANT Avoid turning the vessel or changing channels for one minute after turning on the system 1 Make sure the antenna has a clear view of the sky 2 Turn on your satellite TV receiver and TV 3 Ifa GPS is connected ensure the GPS receiver has obtained an accurate position 4 Apply operating power to the TracVision system TIP When operating power is applied to the ADCU the ADCU initiates a startup sequence The LCD updates as diagnostic tests are performed 5 Wait one minute for system startup The ADCU will display the Tracking Satellit
41. ge area see Figure 1 5 Figure 1 5 Approximate Skew Settings for the PAS 9 Satellite 50 445 For complete details about adjusting the LNB s skew see Setting the LNB Skew Angle Linear Versions Only on page 34 2 Operation TracVision M5 M7 User s Guide Chapter 2 Operation This chapter explains everything you need to know to operate the TracVision system Contents Receiving Satellite TV Signals 13 Turning the System On Off oec ren gatti oni ani 14 Changing Channels and Switching Between Satellites Circular Verstolts icdevadea cvi decet eve ee e I5 Changing Channels and Switching Between Satellites Linear Versions ordinat enti aarnen catre rv 21 Receiver Requirements eene 24 ADCU Display IV DOS sila abun tatenca tsm ataodatiadetegds 26 Product Care s odd cmt eR 29 TracVision M5 M7 User s Guide Chapter 2 Operation Receiving Satellite TV Signals Television satellites are located in fixed positions above the Earth s equator and beam TV signals down to certain regions of the planet not worldwide To receive TV signals from a satellite you must be located within that satellite s unique coverage area TIP For your convenience KVH provides links to several websites that offer satellite coverage information Simply visit our website at www kvh coml footprint Figure 2 1 Location and Coverage Area of DIRECTV 101 Sat
42. he TracVision System sss 58 TracVision M5 M7 User s Guide Chapter 3 Settings Manually Setting Latitude and Longitude When a GPS receiver is detected the TracVision system does not require manually set latitude and longitude values However if an active GPS is not connected you can use the flowchart in Figure 3 1 to manually set the latitude and longitude values in the antenna which will speed up satellite acquisition TIP For your convenience you can determine your approximate latitude and longitude using the Position Grids provided in Appendix E on page 107 Figure 3 1 Setting Latitude and Longitude Manually Default Display Press or to toggle each Menu digit to the desired value then press Enter to accept each digit Longitude EnteD C j Setup display type Enter Next Return Select Next until Control antenna is displayed Control antenna nteD Next Return Then select Yes to confirm your selection Man control antenna Yes ext Return Latitude HHN Longitude HE Set Lat Long Yes Next Return Select Next until Restart antenna is displayed Restart antenna Yes Next Return OG Antenna restarted Set Lat Long Yes Next Return Press or to toggle each digit to the desired value then press Enter to accept each digit Latitude N Ente C 7
43. ibration score Turn off autocalibration IMPORTANT If the system is currently configured to use an external compass you must set the TracVision system to use an internal heading reference before performing this procedure See Setting the Heading Reference Source on page 77 for more information J TracVision M5 M7 User s Guide Appendix B Recalibration Step 1 Clear the Existing Calibration Score Use the flowchart in Figure B 1 to clear the existing calibration score NOTE If the System Halted Power System Off On message is displayed during this procedure turn the system off wait 10 seconds then turn the system on Wait one minute for initialization before restarting the procedure NOTE Be sure to turn the system off after completing this procedure Wait 10 seconds then turn the system on Figure B 1 Clearing the Existing Calibration Score Default Display enu Setup display type Enter Next Return Select Next until Control compass is displayed Control compass nte2 Next Return Then select Yes to confirm your selection Set AutoCal On Off Yes Next Return Select Next until Clear COMPASS Cal is displayed Clear COMPASS Cal Yes Next Return Then select Yes to confirm your selection AutoCal resetting Please wait AutoCal reset done Turn system Off On TracVision M5 M7 User s Guide A
44. me order they were set up in the TracVision system see Figure 2 21 Figure 2 21 Antenna Receiver Synchronization Settings TracVision Satellite Receiver Satellite DiSEqC Setting Satellite A Alternative lor A DiSEqC 1 Satellite B Alternative 2 or B DiSEqC 2 Satellite C Alternative3 or C DiSEqC 3 NOTE Only European Tri Sat configurations track three satellites Chapter 2 Operation TracVision M5 M7 User s Guide ADCU Display Types The ADCU has several display types The default antenna display type displays satellite tracking information The ADCU can also display navigational data when one of the following display types is selected compass pitch roll and yaw rate of turn and latitude longitude Display Type Data This section describes each display type and the data displayed If you wish to change the display type refer to Changing Display Types on page 28 Antenna The antenna display type is the TracVision M5 M7 system s default display type When the ADCU is set to the antenna display type satellite tracking information is displayed Figure 2 22 Tracking Satellite Screen Tracking Sat A Sat B Menu Sat C Available Satellites Selected Satellite Compass The compass display type displays the vessel s heading information If GPS is not connected or if GPS is connected but was not properly initialized prior to turning on the TracVision system the
45. ness Yes Next Return Min Bright Max kkkkkkkkkxk Press to Press to Press to Dim Accept Brighten TracVision M5 M7 User s Guide Chapter 3 Settings Restarting the TracVision System Use the flowchart in Figure 3 27 if you wish to restart the TracVision system Figure 3 27 Restarting the TracVision System lt Default Display gt Menu Setup display type Enter Next Return Select Next until Control antenna is displayed Control antenna nteD Next Return Then select Yes to confirm your selection Man control antenna Yes Next Return Restart Antenna Yes gt Next Return Ou Antenna restarted TracVision M5 M7 User s Guide Chapter 4 Troubleshooting 4 Troubleshooting This chapter identifies potential basic problems along with their possible causes and solutions It also explains how to get technical support Contents Five Simple CCS scat ab atlid ta tbat tutti atn 61 EITOI MOSSQUBS Loses nti ed IERI DEED pha 62 Troubleshooting MEX ront Rh a ERI ERR 64 Causes and Remedies for Operational Issues 65 Technical UD DORE S Esca blac dots doin ho meat 69 im TracVision M5 M7 User s Guide Chapter 4 Troubleshooting Five Simple Checks If you are experiencing a problem receiving satellite TV with your TracVision system perform the five simple checks below TIP You can also try resetting the satellite TV receiver Tu
46. ng Accuracy s Better than 1 lt 2 Better than 2 4 Better than 4 8 Better than 8 BAD CAL Recalibrate Magnetic Environment The magnetic environment rating GOOD POOR BAD indicates the quality of the installation location If the quality is POOR or BAD the GyroTrac sensor should be moved to a more favorable magnetic environment and recalibration should be restarted Calibration Number The calibration number indicates the number of times the sensor has been calibrated This is primarily used to verify that a new calibration has been accepted by the system TracVision M5 M7 User s Guide Appendix B Recalibration Step 5 Set Autocalibration to Off Use the flowchart in Figure B 7 to turn off autocalibration Figure B 7 Setting Autocalibration to Off lt Default Display gt Menu Setup display type Enter ext Return Select Next until Control compass is displayed Control compass nteD Next Return Then select Yes to confirm your selection Set AutoCal On Off Yes Next Return On Select Off then select Enter TracVision M5 M7 User s Guide Appendix B Recalibration Setting the Sensor Offset Values The GyroTrac sensor must be mounted as close to level in pitch and roll as possible with its long axis parallel to the vessel s centerline If the GyroTrac sensor was not mounted according to the guidelines in th
47. ngitude into the system Use the flowchart in Figure 3 11 to manually set the latitude and longitude values When the TracVision system uses current latitude and longitude data satellite acquisition time is minimized TIP For your convenience you can determine your approximate latitude and longitude using the Position Grids provided in Appendix E on page 107 Figure 3 11 Setting Latitude and Longitude Manually lt Default Display gt Press or to toggle each Menu digit to the desired value then press Enter to accept each digit Longitude Setup display type Enter Next Return Select Next until Control Latitude N antenna Longitude HEHE is displayed Control antenna nteD Next Return Set Lat Long Yes Next Return Then select Yes to Select Next confirm your selection until Restart antenna Man control antenna Yes Next Return is displayed Restart antenna Yes gt Next Return Oo Antenna restarted Set Lat Long Yes Next Return Og Press or to toggle each digit to the desired value then press Enter to accept each digit Latitude N LE TracVision M5 M7 User s Guide Chapter 3 Settings Step 3 Configure the Receiver s NOTE If you are connecting multiple receivers repeat this process for each additional receiver You will need to connect each receiver one at a tim
48. ns Only on page 34 to adjust the skew angle TracVision M5 M7 User s Guide Chapter 3 Settings Setting Instant On Mode When Instant On mode is enabled the antenna can immediately receive signals on startup if the vessel has not moved since the antenna was last shut off However if the system is turned off then the vessel moves after last acquiring the satellite via Instant On the antenna will undergo its standard initialization process once it is turned back on resulting in a brief delay NOTE Instant On is disabled by default and is not recommended for DISH Network or ExpressVu configurations Use the flowchart in Figure 3 24 if you wish to enable Instant On mode or if you wish to restore the original setting Figure 3 24 Enabling Disabling Instant On Mode lt Default Display gt Menu Setup display type Enter Next Return Select Next until Control antenna is displayed Control antenna nteD Next Return Then select Yes to confirm your selection Man control antenna Yes Next Return Select Next until Set instant on off is displayed Set instant on off Yes Next Return INSTANT mode OFF Select On or Off as required then select Enter TracVision M5 M7 User s Guide Chapter 3 Settings Setting Sleep Mode When the vessel has come to a stop and holds its position for one minute e g at a dock the antenna unit enter
49. ns how to configure the TracVision system for DISH Network s three satellite service e g TurboHD For operation instructions and additional information on DISH modes refer to Changing Channels and Switching Between Satellites Circular Versions on page 15 Step 1 Configure the System 1 Stop the vessel in a blockage free area 2 Connect a PC to the TracVision system as described in Connecting a PC on page 40 You will enter the following PC commands into the HyperTerminal window An example is provided in Figure 3 10 3 Apply operating power to the TracVision system Turn on the TV s and receiver s 4 Type HALT then press Enter 5 Type the appropriate SATINSTALL command from the table below then press Enter To Configure Type DISH 1000 61 SATINSTALL TRISAT DISH61 DISH 1000 129 TIP Be sure to select the appropriate DISH 1000 configuration for your geographic area Refer to DISH 1000 Required for TurboHD Service on page 15 for more information 6 Type ZAP then press Enter to restart the antenna Wait SATINSTALL TRISAT DISH one minute for system startup Figure 3 10 Example Configuring DISH 1000 61 HALT SATINSTALL TRISAT DISH61 ZAP TracVision M5 M7 User s Guide Chapter 3 Settings Step 2 Update Latitude and Longitude Data if necessary If you do not have a GPS connected to the ADCU you need to enter your vessel s latitude and lo
50. on M5 M7 User s Guide Appendix A Advanced Settings and Functions Updating Satellite Frequency Data If the antenna is unable to find a satellite or if you are unable to receive certain channels the satellite s frequency data might have changed The satellite frequency scan feature allows you to update the frequency data of any satellite stored in the system s library With the desired satellite band and polarization selected the system will automatically search for the frequency with the strongest signal The system will then update that satellite s programmed data with the new frequency and associated network ID and store it in the satellite library You will need to enter the following information Symbol rate FEC code TIP You can find satellite information on the web at www lyngsat com or www satcodx com neither website is affiliated with KVH To update the satellite frequency data follow the steps below IMPORTANT The vessel must remain stationary throughout this procedure 1 Track the satellite you wish to update by choosing a valid polarization band 2 Set your satellite receiver to signal meter mode Refer to your selected receiver s user manual for details 3 Ensure your TV signal meter indicates that you have a strong signal 4 Using the receiver select the desired polarization and band you wish to update Refer to your selected receiver s user manual for details J
51. perTerminal Enter commands in the Wizard s TracVision Antenna Comms window You do not need to flash the antenna to enter commands 1 Connect a serial data cable from the maintenance port DB9 connector located on the back of the ADCU to the serial port on your PC Figure 3 8 Connecting a PC to the ADCU PERE RRR EE EEREEEEEEEEE d e o 0 59 58 57 56 55 54 53 52 5I 50 49 IS 47 46 45 4i 43 32 41 40 35 38 37 9000 Maintenance Port 12345678 TIEHTTITITEIT ps 26 27 28 29 30 31 32 33 M 35 36 TIP If your computer does not have a DB9 serial COM port you can use the following USB to RS232 adapters IO Gear Part GUC232A visit www iogear com Belkin Part tt F5U109 or Belkin Part F5U409 visit www belkin com TracVision M5 M7 User s Guide Chapter 3 Settings 2 Open HyperTerminal and establish the following settings Bits per second 9600 Data bits 8 Parity None Stop Bits 1 Flow Control None Figure 3 9 HyperTerminal Settings COM1 Properties TIP To view characters on the screen as you type set up HyperTerminal to echo typed characters Select Properties from the File menu select ASCII Setup at the Settings tab then select Echo typed characters locally at the ASCII Setup window E TracVision M5 M7 User s Guide Chapter 3 Settings DISH 1000 Setup This section explai
52. ppendix B Recalibration Step 2 Set Autocalibration to On Use the flowchart in Figure B 2 to turn on autocalibration Figure B 2 Setting Autocalibration to On lt Default Display gt Menu Setup display type Enter ext Return Select Next until Control compass is displayed Control compass Ente Next Return Then select Yes to confirm your selection Set AutoCal On Off Yes Next Return AutoCal is On nteD Select On then select Enter ON Off TracVision M5 M7 User s Guide Appendix B Recalibration Step 3 Recalibrate the System a Select a calm day and a clear area Excessive pitching and rolling can distort calibration data b Write down your approximate heading You will use this information later in this procedure c Steer the vessel at a slow steady speed through two full circles that take at least two minutes each to complete Use the heading information you recorded earlier to confirm that you completed each full circle see Figure B 3 TIP The circles do not have to be perfectly round but ensure that you have turned 360 for each circle Figure B 3 Timing Calibration Circles 2 Minutes 1 Minute 30 Seconds 30 Seconds 1 Minute TracVision M5 M7 User s Guide Appendix B Recalibration Step 4 Verify the Calibration Score This section explains how to display and interpret the calibration s
53. pposite direction During this time your TV picture will freeze momentarily TracVision M5 M7 User s Guide Chapter 4 Troubleshooting Technical Support The TracVision M5 M7 antenna is a sophisticated electronic device KVH authorized technicians have the specialized tools and expertise necessary to diagnose and repair a system fault Therefore if you experience any operating problem or require technical assistance please call or visit your local authorized TracVision dealer or distributor To find a KVH authorized dealer near you visit www kvh com wheretogetservice If you need help finding an authorized technician please contact KVH Technical Support North South America Australia Phone 1 401 847 3327 E mail techs kvh com Mon Fri 9 am 6 pm ET 5 GMT Sat 9 am 2 pm ET 5 GMT Europe Middle East Asia Phone 45 45 160 180 E mail support kvh dk Mon Fri 8 am 4 30 pm 1 GMT Please have your antenna serial number handy before you call see Displaying the Antenna Serial Number on page 83 for more information TracVision M5 M7 User s Guide Appendix A Advanced Settings and Functions Appendix A Advanced Settings and Functions This appendix contains information on advanced settings and functions This information should only be utilized by KVH authorized technicians Contents Data Output Settings 9 educunt ust senta th puteos 13 Setting the Heading Reference Source
54. rcularly polarized satellite signals e g North America or linearly polarized satellite signals e g Europe or Latin America Figure 1 3 illustrates the difference between these two polarizations Figure 1 3 Polarizations of Satellite Signals Circular Linear Signals transmitted in two Signals transmitted in vertical corkscrew patterns one and horizontal waves offset running clockwise and one exactly 90 from each other running counter clockwise LNB Skew Angle Since linear satellite signals are oriented in a precise cross pattern the TracVision antenna s receiving element called an LNB low noise block must be oriented in the same way to optimize reception This orientation adjustment is referred to as the LNB s skew angle Figure 1 4 illustrates how skew determines the amount of a linear signal that the LNB collects The more signal the better the reception Figure 1 4 How Skew Works Bad Skew Good Skew Ideal Skew AP Cdp Wn A Satellite Signal 55 LNB Signal Collector i TracVision M5 M7 User s Guide Chapter 1 Introduction The correct skew setting varies depending on your geographic location since the orientation of your antenna to the satellite changes as you move For example if your antenna is tracking the PAS 9 satellite for Sky Mexico programming the ideal skew setting ranges from 30 to 70 depending upon your location within the satellite s covera
55. rn Select Next until Get skew angle is displayed Get skew angle Yes Next Return Skew angle HEE Press any button to exit TracVision M5 M7 User s Guide Chapter 3 Settings Adjusting the Skew Angle Once you have determined the proper skew angle follow the steps below to adjust the antenna s LNB skew angle A CAUTION To avoid bodily injury be sure to turn off the antenna and disconnect power to all wired components 1 Using a Phillips head screwdriver remove the screws securing the radome Then remove the radome and set it aside in a safe place 2 Locate the LNB assembly on the back of the antenna reflector see Figure 3 3 Figure 3 3 Location of LNB on Back of Antenna Reflector Reflector TracVision M5 M7 User s Guide Chapter 3 Settings 3 Using a 2 mm allen hex key loosen the two M4 socket set screws securing the LNB The location of the screws varies according to TracVision model refer to Figure 3 4 or Figure 3 5 Figure 3 4 TracVision M5 Set Screws Reflector M4 Socket Set Screws M4 Socket Set Screws Reflector i Chapter 3 Settings TracVision M5 M7 User s Guide 4a TracVision M5 Only Adjust the LNB clockwise or counter clockwise until the skew arrow on the LNB points to the skew angle that you determined earlier Due to physical constraints if the skew angle is greater than 15
56. rn off and unplug the receiver wait one minute then plug it back in and turn it back on Can the antenna see the satellite The antenna requires an unobstructed view of the sky to receive satellite TV signals Common causes of blockage include boat masts trees buildings bridges and mountains Is there excessive dirt or moisture on the antenna dome Dirt buildup or moisture on the dome can reduce satellite reception Clean the exterior of the dome periodically Is it raining heavily Heavy rain or snow can weaken satellite TV signals Reception should improve once the inclement weather subsides Is everything turned on and connected properly Make sure your TV and receiver are both turned on and set up for the satellite input Finally check any connecting cables to ensure none have come loose Linear Versions Only Is the antenna s LNB set to the correct skew angle To optimize reception the antenna s LNB needs to be set to the correct skew angle for the satellite s you want to track See Setting the LNB Skew Angle Linear Versions Only on page 34 for details im TracVision M5 M7 User s Guide Chapter 4 Troubleshooting Error Messages This section describes potential error messages displayed on the ADCU No GPS Data While System Powerup The No GPS data while system powerup message is not a true error message This indicates that no GPS was detected during TracVision M5 M7 initiali
57. rom antenna error message indicates a communication failure between the ADCU and the antenna This is usually the result of either the antenna being disconnected from the ADCU or the antenna not being turned on If the antenna is not intentionally turned off check for loose cable connections or restart the system For more information on restarting the system refer to Restarting the TracVision System on page 58 TracVision M5 M7 User s Guide Chapter 4 Troubleshooting SYMPTOM Antenna not switching satellites o No picture on TV set Ea ES Certain channels do not work X Hp Intermittent picture for short intervals EER System works at dock but not on the move EN X Pixelating television picture Snowy television picture xf fo fof de 4 ig Troubleshooting Matrix The troubleshooting matrix in Figure 4 1 identifies potential operational symptoms and their causes and remedies Causes and Remedies for Operational Issues on page 65 contains detailed information on the causes and remedies listed below Figure 4 1 Troubleshooting Matrix Ss ww g S 8 E E gt eo e 8 o CLs 4i j of d 8 3 38 g amp 8 S s 8 E 2 PI w E amp o S ela s amp s el lt s e amp s s o Oo amp S oa S S S 5 8 E 2 L 8 8 e amp S E SEJE amp J E J T olo S o s3 S29 m c sS 9 3 38 8 3S 3 8 S o Cf 2 8 8 8 8 2 ES 8 O T a
58. rre prarimescdordom rires usdenc ibt erdtUs Setting SSS Mode cust iret idet idulsdetatei iu aet e e Ufodd Adjusting Display Brightness 5 5 2 rrr teens Restarting the TracVision System sseenne is TracVision M5 M7 User s Guide Table of Contents Troubleshooting Five Simple Sa 6 comer ance en perdon vet trien fnt 61 Error Message i atta atl taut eerie 62 Troubleshooting Matrix i e re tere aret a 64 Causes and Remedies for Operational Issues s 65 Technical SUDBOLE ceo doom RR ER R EN 69 Advanced Settings and Functions Data Output Settings 55d casta ait status tun Decet Byte rs RR nd 13 Setting the Heading Reference Source ees 71 Manually Controlling the Antenna eene 18 Updating Satellite Frequency Data nnne 19 Displaying the Calibration Score enne 81 Displaying the Antenna Software Version eese 82 Displaying the Antenna Serial Number eese 83 Recalibration Recalibrating the System e n merits 87 Setting the Sensor Offset Values eene 94 Receiver Wiring Diagrams Wiring Diagram for One or Two Receivers 99 Wiring Diagram for Three or Four Receivers CIPCULSTCVBESIOTIS 2 oeil irit ricco teo dudo odo Ededecuce Ped ont 100 Wiring Diagram for Three or Four Receivers Linear Quad o
59. s Sleep Mode which locks the antenna in place to conserve power As soon as the vessel moves beyond a 1 2 window or the signal level changes significantly Sleep Mode automatically turns off and the system begins tracking the satellite again or enters Search Mode to find the satellite Use the flowchart in Figure 3 25 if you wish to disable Sleep Mode or if you wish to restore the original Sleep Mode setting Figure 3 25 Setting Sleep Mode On Off Default Display Menu Setup display type Enter Next Return Select Next until Control antenna is displayed Control antenna amp nteD Next Return Then select Yes to confirm your selection Man control antenna Yes Return Select Next until Set sleep on off is displayed Set sleep on off Yes Next Return O SLEEP mode ON Select On or Off as required then select Enter TracVision M5 M7 User s Guide Chapter 3 Settings Adjusting Display Brightness You can adjust the brightness of the ADCU s LCD screen to suit your preferences Use the flowchart in Figure 3 26 if you wish to adjust the display brightness Figure 3 26 Setting Display Brightness lt Default Display gt Menu Setup display type Enter Next Return Select Next until Setup configuration is displayed Setup configuration amp nteD Next Return Then select Yes to confirm your selection Set bright
60. t DIRECTV is an official trademark of DIRECTV Inc DISH Network is an official trademark of EchoStar Communications Corporation ExpressVu is a property of Bell ExpressVu a wholly owned subsidiary of Bell Satellite Services All other trademarks are the property of their respective owners TracVision M5 M7 User s Guide Table of Contents Table of Contents Introduction Usi g this M GNU a csse vu pv a al alo nad pdt n buta Syste ni OVEIVIGW s dee ed eek t Wadi a Dn re ae b vane d cede use Circular and Linear Veretenis vd aa axiad ad ax ed bebe a eee Operation Receiving Satellite TV Signals enne Turning the System On Off sssssssseeeneennnnnnn Changing Channels and Switching Between Satellites Circ lar VERSIONS S atn dfe bero DC Db EP OPE HT Changing Channels and Switching Between Satellites Linear Versin S nanciare epe fet upra ev ea atn kt a Receiver Requirements sseeeeeeeennennnnennnnnnnnnnns ADCU Display TYPES putinii PROUT EIA SEEE EEE AAAA AAAA AEAEE Settings Manually Setting Latitude and Longitude Setting the LNB Skew Angle Linear Versions Only Connecting a PC UPC NCC CTUM nU DISH EBOUES OBI aes fd osten danfan iof fes Dual Sat or Single Satellite Setups ess European Tri Sat Mode Setup seen Setting Instant On Mode 2 noo
61. t 1 also has a pass through duplicate port Bach serial port can be independently programmed to output data at a rate from 1 Hz to 20 Hz selectable in 1 Hz increments The default data rate is 10 Hz NOTE Serial port 3 is disabled If serial port 3 is selected the No Port 3 TV Setup screen will be displayed Press any key to exit the screen Message Formats NMEA The NMEA message format conforms to the NMEA 0183 version 2 20 standard for message structure The following NMEA outputs can be selected BWC GGA GLL HDG HDM HDT VTG and XTE NOTE The data rate of serial port 1 is 4800 baud the default data rate of serial port 2 is 9600 baud However if serial port 2 is selected for NMEA output the baud rate is automatically changed to 4800 baud KVH RS 422 The KVH message format is an RS 422 message format giving stabilized pitch roll and yaw data Data output from port 1 will be 4800 baud while data port 2 will be 9600 baud this message can be used for any device that is able to receive this data rate Cetrek Proprietary The Cetrek proprietary message format is a stabilized heading output for use with Cetrek autopilot systems If an active GPS connection is detected you can select either magnetic or true heading J TracVision M5 M7 User s Guide Appendix A Advanced Settings and Functions Use the flowchart in Figure A 2 to modify the serial output settings or if you wish to restore the original outpu
62. t No GPS Installed GPS Installed until Control antenna is displayed Press or to toggle each Control antennae a giu e ie E EnteD Next Return press er to accept each digit Latitude N Then select Yes to confirm your selection ee Enter lt gt Man control antenna Yes Next Return Press or to toggle each Select Next digit to the desired value then until Install press Enter to accept each digit satellite Longitude HHE is displayed C D GnteD C 3 Latitude N Install satellite Ye Next Return Longitude IHHEE Install A SAT NAME p ia Cancel Restart antenna Select Next until the Yes No desired satellite is displayed then select Yes Install B lt SAT NAME gt Cancel i i E d Select Next until the desired satellite is displayed then select Yes NUN TracVision M5 M7 User s Guide Chapter 3 Settings Step 3 Configure the Receiver s if required Linear configurations without a multiswitch DISH Network and ExpressVu subscribers require receiver configuration The following sections explain how to configure the receiver s for TracVision use Linear Configurations If your TracVision system does not include a multiswitch you can configure the receivers to enable automatic switching See Linear Receiver Configuration on page 25 for more information Circular Configurations This section explains how to configure the TracVision
63. t settings Figure A 2 Serial Output Settings Default Display Menu Setup display type Enter Next Return Setup data outputs ented Next Return Then select Yes to confirm your selection Set sine cos levels Yes Next Return Set serial outputs Next Return D NMEA Configuration Select output B WC Yes gt Cancel Select Next to toggle output types BWC GGA GLL HDG HDM HDT VTG and XTE as required then select Yes Setting selection Please wait Select output BWC Yes Next Select Cancel to accept the selection 4 Select serial port 1 Cancel f Select Next to toggle ports as required then select Yes Serial port 1 config Output Data NMEA Set speed 10 Hz Select or as required then select Enter Resetting outputs No O Outputs erasing Please Wait Select output type E P J B Cetrek Configuration Cetrek data is Mag nteD Cru Select Mag or True then select Enter This displays only if a valid GPS connection is detected TracVision M5 M7 User s Guide Appendix A Advanced Settings and Functions Setting the Heading Reference Source You can set the heading reference source to internal default or external When internal heading data is selected the system receives heading data from the GyroTrac s sensor You can select external heading data if an external compass is connected to the system Use the flowchart in
64. tails or visit any KVH authorized dealer or distributor for assistance To find a KVH authorized dealer near you visit www kvh com wheretogetservice Satellite Frequency Data Changed If some channels work while one or more other channels do not or if the antenna cannot find the selected satellite the satellite s frequency data might have changed You can visit any KVH authorized dealer or distributor for assistance To find a KVH authorized dealer near you visit www kvh com wheretogetservice Vessel Turning During Startup If you turn the vessel during the first minute after system startup the gyro calibration that occurs during startup might become invalid causing the TracVision M5 M7 system to track improperly To solve this problem simply turn off the TracVision M5 M7 system for at least ten seconds Then turn on the TracVision system ensuring the vessel is either motionless or traveling in a straight line for the first minute after startup Insufficient Power If the power cable to the antenna unit is more than 50 ft 15 m long the power level can decrease over the length of the cable resulting in a voltage level at the antenna that is too low to power the system Refer to the TracVision M5 M7 Installation Guide for details on supplying adequate power to the antenna or visit any KVH authorized dealer or distributor for assistance To find a KVH authorized dealer near you visit www kvh com wheretogetservice Improper
65. tenna motors keeping the antenna pointed at the satellite at all times even while you re on the move Satellite Tracking and Switching Your TracVision system tracks your selected satellites as long as the vessel is located within the selected satellites coverage area During installation your TracVision system should have been set up to track your desired satellites allowing you to switch between them quickly and easily Satellite Library The TracVision M5 M7 includes a pre programmed satellite library of the most popular satellite services offering a wide variety of satellite services to choose from For complete information on the satellite library see Settings on page 31 TIP You can add two more satellites of your choice to the satellite library For complete information on adding satellites to the library refer to the associated Application Note on the KVH Partner Portal KVH authorized technicians only Navigational Data Besides displaying satellite tracking information the ADCU can also display navigational data including magnetic heading true heading pitch roll yaw rate of turn and latitude and longitude position data NOTE Some displays require an active GPS connection For more information on display types see ADCU Display Types on page 26 TracVision M5 M7 User s Guide Chapter 1 Introduction Circular and Linear Versions Your TracVision system is configured to receive either ci
66. turn TracVision M5 M7 User s Guide Chapter 1 Introduction Related Documentation In addition to this User s Guide the following documents are provided with your TracVision system Document Description Installation Guide Complete product installation instructions Product Registration Form Details on registering the product Warranty Statement Warranty terms and conditions Contents List List of every part supplied in the kit im TracVision M5 M7 User s Guide Chapter 1 Introduction System Overview Your TracVision M5 M7 is a state of the art actively stabilized antenna system that delivers live satellite TV to your vessel s audio video entertainment system A basic system is illustrated below Figure 1 2 TracVision System Diagram Typical Installation TracVision Antenna Vessel Power 12 16 VDC Pm TRAGVISION eas KlviHr Vessel Power 12 16 VDC Satellite Receiver s TV s Purchased Separately Advanced Digital Control Unit ADCU Optional Interfaces GyroTrac Sensor Autopilots GPS or Ship s Gyro Plotters Radars Remote Displays TIP TracVision receiver wiring diagrams are provided in Appendix C on page 97 ADCU wiring diagrams are provided in Appendix D on page 103 System Components TracVision M5 M7 User s Guide Chapter 1 Introduction The TracVision M5 M7 includes the following
67. ure A 8 Displaying the Antenna Serial Number lt Default Display gt Menu Setup display type Enter Next Return Select Next until Get antenna status is displayed Get antenna status nteD Next Return Then select Yes to confirm your selection Get system error Yes Next Return Select Next until Get serial number is displayed Get serial number Yes Next Return Antenna serial THHHEHHHBHIE TracVision M5 M7 User s Guide Appendix B Recalibration Appendix B Recalibration This appendix explains how to recalibrate the system and set gyro offset values This information should only be utilized by KVH authorized technicians Contents Recalibrating the System eso repe 87 Setting the Sensor Offset Values 94 TracVision M5 M7 User s Guide Appendix B Recalibration Recalibrating the System During installation the TracVision M5 M7 system should have been properly calibrated However if the GyroTrac sensor is moved to another location or if additional metallic equipment is installed or removed near the GyroTrac sensor KVH recommends recalibrating the system This section explains how to recalibrate the system To perform this procedure you will need to perform the following Clear the existing calibration score Turn on autocalibration Recalibrate the system Verify the cal
68. utput Versions nn 101 ADCU Wiring Diagrams ADCU Wiring Diagram Required neee 105 ADCU Wiring Diagram Optional Equipment 106 Position Grids European Position Gd ss oo oe etre prit rper EE ed 109 North American Position Gd usse coe ret Y a roms 110 TracVision M5 M7 User s Guide Chapter 1 Introduction 1 Introduction This chapter provides a basic overview of this manual and your TracVision system Contents Dein this Manual ttt tbl cantata bbe 3 System OUSCVIB Wo dtt xp a uu ev e dtd 6 Circular and Linear Versions 9 im TracVision M5 M7 User s Guide Chapter 1 Introduction Using this Manual This manual provides complete operation setup and troubleshooting information for your TracVision system as well as wiring diagrams for various TracVision M5 M7 configurations Who Should Use This Manual The user should refer to the Operation chapter to learn how to operate the system The user installer or servicing technician should refer to the Settings chapter for information on configuring the system and the Receiver Wiring Diagrams appendix for information on connecting additional receivers The user and or servicing technician should refer to the Advanced Settings and Functions appendix for information on advanced settings and operational procedures The user and or servicing technician should refer
69. zation If no GPS receiver is connected or if the GPS receiver was not initialized prior to turning on the TracVision system some navigational display types will be unavailable TIP For information on ADCU display types refer to ADCU Display Types on page 26 If a GPS receiver is connected but was not initialized prior to turning on the TracVision system simply turn off the TracVision system initialize the GPS receiver then turn the TracVision system back on The TracVision system will detect the GPS sensor during initialization Refer to Turning the System On Off on page 14 for more information Antenna Response Incorrect The Antenna response incorrect error message indicates that the ADCU received an incorrect response from the antenna when requesting data To correct this simply repeat the requested operation Antenna Not Responding The Antenna not responding error message indicates a communication failure between the ADCU and the antenna This is usually the result of either the antenna being disconnected from the ADCU or the antenna not being turned on If the antenna is intentionally turned off switch to one of the navigational display types to use the navigational displays TIP For information on ADCU display types refer to ADCU Display Types on page 26 TracVision M5 M7 User s Guide Chapter 4 Troubleshooting TV Comms is Off No Data from Antenna The TV comms is off no data f

Download Pdf Manuals

Related Search

Related Contents

Acronis® Backup & Recovery for Mac® Acronis Backup & Recovery  Olympus C-25 User's Manual    service manual super audio cd player  ADOBE® PRESENTER®    USER MANUAL FOR SX-3000 STANDALONE  LECOASPIRA ANIMAL - M0S09203 1Q03:Layout 1.qxd  Boss BV6654B - Boss Audio Systems  Manuale Utente PCA 60 USB (italiano)  

Copyright © All rights reserved. Failed to retrieve file