Phoenix Manual.indd
Contents
1. cup washers and pivot covers Note use a 1 4 hex head wrench to remove yoke bolts Stretch yoke and snap it into short yoke position Replace pivot covers cup washers and yoke bolts 5 Replace T Handle into square hole keeping the washer between handle and yoke ADJUSTING YOKE With one hand on ring handle to hold unit loosen T Handle 2 Tilt unit to desired angle Note Reference angles have been molded on the pivot cover to make adjustments easier and more precise 3 Tighten T Handle to secure fixture in place ROTATING SHUTTER ASSEMBLY Loosen shutter rotation lock knob on either side of the luminaire 2 Rotate shutter assembly 360 in either direction 3 Tighten shutter rotation lock knobs to secure shutter as sembly 4 To lock the shutters in place rotate the Shutter Lock Lever until proper tension is applied to shutters INSTALLING C CLAMP The C clamp is used to mount the luminaire to a pipe hang position The C clamp attaches to the top of the yoke via the 1 2 bolt provided with the C clamp Be sure to keep the washer between the bolt head and the yoke hata Altman Lighting Inc 57 Alexander St Yonkers NY 10701 1 800 4 ALTMAN SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE COPYRIGHT 2012 ALTMAN LIGHTING INC ALL RIGHTS RESERVED ADJUSTING LAMP With power on and all four shutters open shine light onto a surface perpendicular to fixture and adjust for sharp focus 2 Ro2. either direction The use of a donut will sharpen the image ACCESSORY RETAINING LATCH This unique retaining hatch is designed for positive locking and manual return 1 Slide Clip to right side 2 Swing latch back 3 Insert accessory 4 Close latch Make sure latch locks in place Centering Distance Knob Knob lt gt Y Cap 7 Screw Pattern Reflector Housing Screws Altman Lighting Inc 57 Alexander St Yonkers NY 10701 1 800 4 ALTMAN SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE COPYRIGHT 2012 ALTMAN LIGHTING INC ALL RIGHTS RESERVED INSTALLING SHUTTER PLATES 1 Pressure Plate completely flat Install such that the tabs are on the top and bottom and sides Iris and spring plate Install so that the 4 studs face the back of the unit 2 SHUTTERS 1 The shutters are not removable without dissembling the unit 2 Care must be given to make sure each of the four shutters stay in their proper positions in between the shutter plates Top latch cover Barrel screws 50 4 5 X 6 36 6 X 9 Plates CLEANING REPLACING LENSES 1 Remove focus lock knob push in safety pin and slide lens barrel out Place barrel on a surface so that the two halves are oriented as the top an
3. Caution Read and understand these entire instructions before proceeding Caution Always wear safety goggle and gloves when servicing this equipment MAN Lighting BRINGING IMAGINATIONTOWIGHT Mbaroi Awas indoors M or iee m Samp RENG Caution This luminaire is a source of intense heat and is not intended for residential use To reduce risk of fire or injury avoid contact by persons or materials If luminaire is hot allow to cool before re lamping Caution DO NOT touch glass portion of lamp with your hands Agents such as sodium grease or oil from your fingers may be transferred to the glass wall The contaminants can cause the lamp to rupture or can greatly reduce the performance and life of the lamp If accidentally soiled immediately clean the lamp with a soft clean and lint free cloth soaked in methylated I i spirits denatured alcohol then polish with a dry soft clean I D S O I a and lint free cloth Caution DO NOT allow materials to come in contact with e hot lamp Protect lamp from abrasions and scratches These S ot t lamps reach very high temperatures as high as 1740 F 950 C Under certain circumstances internal or external influences may cause lamp to rupture Caution Disconnect unit from electrical supply before initial lamp installation re lamping or servicing for any reason INTRODUCTION C tulati hasi f the finet EF ACEC TAN INICTDIITZTIONNIC ighting P available iy Bee as
4. SAFETY INSTRUCTIONS your Phoenix Ellipsoidal Spotlight be sure to read all ot theinetruchonsimthis manual SAVE THESE INSTRUCTIONS FOR FUTURE USE LAMP CAP ASSEMBLY SHUTTER ROTATION LOCK KNOB SHUTTERS LUMINAIRE BODY S FOCUS LOCKING KNOB DROP IN IRIS SLOT S YOKE SHUTTER ASSEMBLY YOKE LOCKING KNOB LENS TUBE PATTERN LOCKING LEVER Wl AN MAY l P ae FLIPPER COLOR FRAME ACCESSORY HOLDER Altman Lighting Inc 57 Alexander St Yonkers NY 10701 1 800 4 ALTMAN SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE COPYRIGHT 20120 ALTMAN LIGHTING INC ALL RIGHTS RESERVED INSTALLING THE LAMP CAUTION Do not use any lamps exceeding 750W or permanent damage will result CAUTION DO NOT touch the glass portion of the lamp with your hands CAUTION Disconnect fixture before re lamping 1 Loosen cap screw until it spins freely 2 Pulllamp cap straight out from the luminaire body 3 With protective wrap still in place grasp lamp at base and gently push into socket until firmly seated 4 Remove protective wrap from bulb and replace lamp cap into luminaire body 5 Tighten cap screw Cap Assembly Shutter Rotation Lock Knob Shutter Handle Short Yoke Position OO Shutter Assembly Cup Washers Pivot Covers USING SHORT YOKE POSITION Remove T Handle and its associated hardware j Remove yoke bolts
5. d bottom Remove lower accessory cover with 2 screws Remove top latch cover with 2 screws Remove 4 barrel screws one on each side Carefully remove top half of the barrel Replace or clean lenses with mild soap and water and a clean lint free cloth Replace top half of barrel top latch cover bottom cover and re install screws Slide lens barrel back into unit and replace focus lock knobs WARNING Never use glass or window cleaner or any abrasive material to clean alens These types of cleaners will stain the lens surface Abrasive materials will damage the surface of the lens N 19 6 X 16 26 6 X 12 Altman Lighting Inc 57 Alexander St Yonkers NY 10701 1 800 4 ALTMAN SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE COPYRIGHT 2012 ALTMAN LIGHTING INC ALL RIGHTS RESERVED
6. tate distance knob all the way to the left to put unit into peak focus 3 Loosen centering knob slightly and adjust so the hot spot is in the center of the beam of light Tighten centering knob to lock lamp in place 4 Turndistance knob to the right until desired field is achieved The more you turn to the right the flatter the field will get DROP IN IRIS SLOT This larger slot can accept either a drop in iris or a motorized pattern device gobo rotator yo yo etc The slot has a retractable cover to prevent light leak when not in use When a device is used the cover should be closed to the edge of the device placed in the slot When a drop in iris is used always place it so the flat side is facing the shutters CLEANING THE REFLECTOR Remove lamp cap from luminaire Remove yoke from luminaire Remove shutter assembly rotation lock knobs Remove the four screws from the reflector housing Lift off the top half of the reflector housing Dampen a clean lint free cloth with denatured alcohol and gently wipe reflector clean Align reflector with locating springs replace luminaire body top 7 Re install four screws in luminaire body WARNING never use glass or window cleaner or any abrasive material to clean the reflector Use of these items will damage the reflector OV a NS PATTERN PROJECTION The pattern holder slot accepts standard ETC Source 4 size pattern holders The image of the pattern can be rotated 360 in
Download Pdf Manuals
Related Search