Home

HP Color LaserJet CM4730 MFP User Guide - ENWW

1. 1 Foreign interface harness FIH 2 USB 2 0 3 ACC accessory port uses host USB protocol 4 Fax connection for connecting to an optional analog fax accessory 5 Parallel port 6 EIO interface expansion slot 7 Access port for Kensington lock 8 Network connection embedded HP Jetdirect print server 9 AUX port Serial number and model number location The model number and serial number are listed on identification labels located on the rear of the printer The serial number contains information about the country region of origin the printer version production code and the production number of the printer ENWW Product walkaround 11 model product number Hewlett Packard 50 60 Hz 115V 11311 Chinden Blvd Boise Idaho 83704 Model No Q3668 d VERAM Serial No JPBB605112 Assemble i in U S A printer engine made in Japan serial number Figure 1 1 Sample model and serial number label Model name Model number HP Color LaserJet CM4730 MFP CB480A HP Color LaserJet CM4730f MFP CB481A HP Color LaserJet CM4730fsk MFP CB482A HP Color LaserJet CM4730fm MFP CB483A 12 Chapter 1 Product basics ENWW 2 Control panel e Use the control panel e Navigate the Administration menu e Information menu e Default Job Options menu e Time Scheduling menu e Management menu e Initial Setup menu e Device Behavi
2. ENWW Adjust the copy settings 157 Copy two sided documents Two sided documents can be copied manually or automatically Copying two sided documents manually Copies resulting from this procedure are printed on one side and need to be hand collated 1 Load the documents to be copied into the document feeder input tray with the first page facing up and with the top of the page leading into the document feeder Touch Start Copy The odd numbered pages are copied and printed Remove the stack from the document feeder output tray and reload the stack with the last page facing up and with the top of the page leading into the document feeder Touch Start Copy The even numbered pages are copied and printed Collate the odd and even numbered printed copies Copy two sided documents automatically The default copy setting is one sided to one sided Use the following procedures to change the setting so you can copy from or to documents that are two sided Make two sided copies from one sided documents 1 2 3 4 5 6 Load the documents to be copied into the document feeder with the first page facing up and with the top of the page leading On the control panel touch Copy Touch Sides Touch 1 sided original 2 sided output Touch OK Touch Start Copy Make two sided copies from two sided documents 1 Load the documents to be copied into the document
3. eas 178 Connect the fax accessory to a phone line sssss 178 Configure and use the fax features sssssssssssssseneeeene eene 179 Ben A 180 14 Manage the MFP nifel air irojaMor To e 182 Embedded Web server 2 eccceeeccecceeeeeeeeeeeeeeeeeaaeaeeeeeeeeeeeeeesecaeaaeaaeseeeeeeeeeeeseetacecacaeeaeeeeeeeeeetenea 184 Open the embedded Web server 2 c cccccceececeeeeeeeeeeeeceeaaaeeaeceeeeeeeeeseeseeeeessnnaeaaeeees 184 Information tab edges dta nee aa C ER ORAN EORR RA e AA 185 Settings tab Peor e dct ERR Exe dert ae gea 185 Digital Sending tab creto rt E1 Go ree eI DI get pe Dn Aga REDDE e xata Reed deed 186 Asi er aInenrzloc D 186 Other cem 186 FP Easy Printer Care SOftWAre 2 end ER dar ba Ram ERR gr E eap RE a a Ra cauda 188 Supported operating systems sssssssssssssssssseeneeneeenennn enne nennen nennen 188 Open HP Easy Printer Care software sssssssssssee een eene 188 viii ENWW HP Easy Printer Care software sections sssssssssssseenn ene 188 HP Web Jetadmin software ssssssssssssssssssssssesesseeener ne enne nennen nennen nne ertren enne 190 HP Printer Utility for Macintosh ssssssseen emn nennen nennen nennen nennen 191 Oper the HP
4. sssssssssesseseeeneeeee 258 Envelopes jam or will not feed in the MFP sssssseennm emen 258 X ENWW ENWW Output is curled or wrinkled a ee a nemen nnns nis 259 Printer will not duplex or duplexes incorrectly ssssssssssse 259 Understand accessory lights for the 3 bin mailbox and stapler stacker ssesesssss 260 Understand lights on the formatter ssssssssseseeennnemeeeemnemm mener nenne 261 HP Jetdirect EEDS 5 oo rt t eee arret gode a tete Ditis ero ded 261 Heartbeat LED eec o ace eet eee eee 261 Correct print quality and copy quality problems cccceceeeeeeeeeeeeeeeeeeeeeeeeaeeeaaecaaeeaeeaeeeeeeeeeeees 263 Print quality problems associated with media ssssssssssssss 263 Color printing problems 2 sedate soe cohetes de Dee cesa Il ngu aiaeei den tU auae c de Ldbg ee 263 Printout color eITorc z uote nte ean ete tube tust 263 Inicorrect shade te tt t EPI Enea nio hada AO E 264 MISSING COIOM P 264 Cartridge eror been Pme ase ease MN 264 Colormatch eITOr sz tht ote etait eem had tente neus 264 Overhead transparency defects ssssssssssssssseeeee eene 265 Print quality problems associated with the environment ssssssse 265 Print quality problems associated with jams ssssem 265 Print quality troubleshooting pages
5. sseesese 204 Use MS DOS commands to upgrade the firmware sssssssssss 204 Use the HP Jetdirect firmware cccccccceecceec eee ceeee cee e eee eeeeeeaaeeanaaaeeaeceeeeeeeeeeeeeeeeeeeneeees 204 Manage Memo ermi iic tenga cio ee pa a Ad HER Re dora te Afcaeasta lanteapanallatetgags dab GS 206 Manage supplies iiec ea a et v ime ab pex a Peete ttdas tevatadtdes caaaterabecerutadianie 207 HP print cartridges id ree Re e Reb Aderat tete iR 207 Non HP print cartridges 2 n erate ined dah aede 207 Print cartridge authentication sssssssseeeneene eene 207 ENWW ix HP fraud NOTING 2 eeu eee Ce tact eae o deca Ge Pobre ende ese a lddse d ken MUR 207 Print cartridge storage ener eon apa ERE EEE EHE one caa pa oae ex RE edu 207 Print cartridge life expectanoy ie iiseeesec isnt erre ten esL tenue SAU Ie Re dE EE Inn ne dude nh 208 Check the print cartridge life ssssssseem emm 208 On the MFP control panel cccceceeceeeee eee e cette tee eeeeaeeeeaeaeaaneaeeaaeeaeeeeeees 208 In the embedded Web server cccccccecceceeeeeeeeeeteeceecenaaecaeeeeeeeeeereeteteetess 208 Through HP Easy Printer Care software sssssssseee 208 Through HP Web Jetadmin sss enm een 208 15 Maintenance BCIOEICESNOUICC EE NEEE 210 Locate Supplies ir I rite re ent e t
6. sssssssseeeeeenmeem meer nnns 309 Appendix C MFP specifications Physical specifICatlons ii cuoi eer cadet cur e eee ae c dad ee ie en eed rid Le A eue 312 Electrical specifications ssssssssssssssssesseeseerere nnne eren nnns nennen nnn nns 313 A o sti specificationS ETE 314 Environmental SpecifICatlons 5 ennt It tae htec eee Rp eund ak RR een PR aa aiaa aa aada 315 Appendix D Regulatory information xii Compliance with FCC regulations sssssssseeeennee nenne nennen nenne enne nenne 318 Declaration of ConfOrtnlty deett rte ert derriere Annee Erebi aa ED ed RE RR Ee Rua ens 319 Environmental product stewardship program sssssssssssesseeeeeeeem nmn nnne 320 Protecting the environment o coi reci teet eroe PR EEIE Ine eR ETn een E 320 OZONE PFODUCUON a ssn a a a a aaa raaa aaia iea Ea 320 el meeniUnieuem niinn aaa aaa a aa iaa 320 Toner CONSUMPUON aessa EE 320 mdp 320 Lc M 320 HP LaserJet print supplies sssssssssssssssseeeeeneeneen enne ntr nnns 320 Return and recycling instructions ersav ieina iaaa EE eene 321 United States and Puerto Rico c ccccecceeceeeeeeeeeeeeeeeseeeeeaeeeeaeaaeeeeeeeeeeees 321 ENWW Multiple returns two to eight cartridges ssesesssss 321
7. M 1 Long edge landscape This layout is often used in accounting data processing and spreadsheet programs Every other printed image is oriented upside down Facing pages are read continuously from top to bottom 2 Short edge landscape Each printed image is oriented right side up Facing pages are read from top to bottom on the left page and then from top to bottom on the right page 3 Long edge portrait This is the default setting and the most common layout used with every printed image oriented right side up Facing pages are read from top to bottom on the first page and then from top to bottom on the second page 4 Short edge portrait This layout is often used with clipboards Every other printed image is oriented upside down Facing pages are read continuously from top to bottom 130 Chapter 9 Print tasks ENWW Options for binding two sided printing jobs Before printing a two sided document use the printer driver to select the binding Long edge or book binding is the conventional layout used in book binding Short edge or tablet binding is the typical calendar binding ET NOTE The default binding setting is to bind on the long edge when the page is set up for portrait orientation To change to long edge binding click the Flip Pages Up check box Manual duplex printing Print on both sides manually 1 Insert enough paper i
8. 5 Scroll bar Touch the up or down arrows on the scroll bar to see the complete list of available features 6 Sign Out Touch Sign Out to sign out of the device if you have signed in for access to restricted features After you sign out the device restores all options to the default settings 7 Network Address Touch Network Address to find information about the network connection 8 Date and time The current date and time appear here The system administrator can select the format that the device uses to show the date and time for example 12 hour format or 24 hour format ENWW Use the control panel 15 Buttons on the touchscreen The status line on the touchscreen provides information about the status of the device Various buttons can appear in this area The following table describes each button N Home button Touch the home button to go to the Home screen from any other screen Start button Touch the Start button to begin the action for the feature that you are using ER NOTE The name of this button changes for each feature For example in the Copy feature the i button is named Start Copy Stop button If the device is processing a print or fax job the Stop button appears instead of the Start button Touch the Stop button to halt the current job The device prompts you to cancel the job or to resume it Error button The error button appears whenever the device has an error that req
9. Check to see if more than two nonpowered USB hubs are connected in a row on the chain Disconnect all of the devices from the chain and connect the cable directly to the USB port on the host computer ER NOTE The iMac keyboard is a nonpowered USB hub 294 Chapter 16 Problem solving ENWW A Supplies and accessories This section provides information about ordering parts supplies and accessories Use only parts and accessories that are specifically designed for this MFP e Order parts accessories and supplies e Optional output devices e Part numbers ENWW 295 Order parts accessories and supplies e Order directly from HP e Order through service or support providers e Order directly through the embedded Web server Order directly from HP You can obtain the following directly from HP e Replacement parts To order replacement parts in the U S see http www hp com buy parts Outside the United States order parts by contacting your local authorized HP service center e Supplies and accessories To order supplies in the U S see http www hp com go ljsupplies To order supplies worldwide see http www hp com ghp buyonline html To order accessories see http www hp com support licm4730mfp Order through service or support providers To order a part or accessory contact an HP authorized service or support provider Order directly through the embedded Web server 1 In the
10. Router Unavailable If a router is not available the print server should attempt to obtain its stateful configuration from a DHCPV6 server Always Whether or not a router is available the print server always attempts to obtain its stateful configuration from a DHCPV6 server Primary DNS Use this item to specify an IPv6 address for a primary DNS server that the print server should use Secondary DNS Use this item to specify an IPv6 address for a secondary DNS server that the print server should use Proxy Server Specifies the proxy server to be used by embedded applications in the device A proxy server is typically used by network clients for Internet access It caches Web pages and provides a degree of Internet security for those clients To specify a proxy server enter its IPv4 address or fully qualified domain name The name can be up to 255 octets For some networks you may need to contact your Independent Service Provider ISP for the proxy server address Proxy Port Type the port number used by the proxy server for client support The port number identifies the port reserved for proxy activity on your network and can be a value from 0 to 65535 ENWW Initial Setup menu 33 Table 2 11 Jetdirect menus continued Menu item Sub menu item Sub menu item Values and Description IPX SPX Enable Off Disable the IPX SPX protocol On default Enable the IPX SPX protocol Frame
11. Select the settings that you want to use to print specific pages on different paper Click Add Click OK to return to the Paper Quality tab Click OK ET NOTE The paper size must be the same for all pages of the print job Print a blank first page d on 0 or O P On the File menu in the software program click Print Select the driver and then click Properties or Preferences Click the Paper Quality tab In the Special pages list box click Covers Click Settings Select the settings that you want to use to add blank or preprinted covers Click Add Click OK to return to the Paper Quality tab Click OK Use watermarks A watermark is a notice such as Confidential that is printed in the background of each page of a document 1 Onthe File menu in the software program click Print 2 Select the driver and then click Properties or Preferences 3 From the Effects tab click the Watermarks drop down list 4 Click the watermark that you want to use To create a new watermark click Edit 5 If you want the watermark to appear only on the first page of the document click First Page Only 6 Click OK To remove the watermark click none in the Watermarks drop down list Resize documents Use the document resizing options to scale a document to a percentage of its normal size You can also choose to print a document on a different size paper with or without scaling ENWW Windows printer driver fea
12. Table 2 1 Information menu continued Menu item Sub menu item Sub menu item Values Description Sample Pages Fonts Demonstration Page Print A demonstration page that displays the highest print quality possible for this MFP RGB Samples Print Printout of color samples for different RGB values The samples act as a guide for color matching CMYK Samples Print Printout of color samples for different CMYK values The samples act as a guide for color matching PCL Font List Print A list of printer control language PCL fonts that are currently available on the device PS Font List Print A list of PostScript PS fonts that are currently available on the device ENWW Information menu 19 Default Job Options menu Administration gt Default Job Options Use this menu to define the default job options for each function These are used if the user does not specify other options when creating the job The Default Job Options menu contains the following sub menus e Default Options for Originals e Image adjustment e Default Copy Options e Default Fax Options e Default E mail Options e Default Send to Folder Options e Default Print Options Default Options for Originals Administration gt Default Job Options gt Default Options For Originals Table 2 2 Default Options for Originals menu Menu item Values Description Paper Size Select a paper size from the list Se
13. The Administration menu has several sub menus which are listed on the left side of the screen Touch the name of a menu to expand the structure A plus sign next to a menu name means that it contains sub menus Continue opening the structure until you reach the option that you want to configure To return to the previous level touch Back To exit the Administration menu touch the Home button in the upper left corner of the screen The device has built in Help that explains each of the features that are available through the menus Help is available for many menus on the right hand side of the touchscreen Or to open the global Help system touch the Help button in the upper right corner of the screen The tables in the sections that follow indicate the overall structure of each menu under the Administration menu Navigate the Administration menu 17 Information menu Administration Information Use this menu to print information pages and reports that are stored internally on the device Table 2 1 Information menu Menu item Sub menu item Sub menu item Values Description Configuration Status Administration Menu Print Shows the basic structure of the Pages Map Administration menu and current administration settings Configuration status Print A set of configuration pages that show the Pages current device settings Supplies Status Print Shows the status of supplies such as Page cartridges mainten
14. iis rig m ENWW Install memory and fonts 331 6 Toreplace a DDR DIMM that is currently installed spread the latches apart on each side of the DIMM slot lift the DDR DIMM up at an angle and pull it out 7 Remove the new DIMM from the antistatic package Locate the alignment notch on the bottom edge of the DIMM 8 Holding the DIMM by the edges align the notch on the DIMM with the bar in the DIMM slot at an angle and firmly press the DIMM into the slot until it is fully seated When installed correctly the metal contacts are not visible 332 Appendix E Install memory and print server cards ENWW 9 Push down on the DIMM until both latches engage the DIMM ET NOTE If you have difficulty inserting the DIMM make sure the notch on the bottom of the DIMM is aligned with the bar in the slot If the DIMM still does not go in make sure you are using the correct type of DIMM 10 Align the formatter board in the tracks at the bottom of the slot and then slide the board back into the MFP ET NOTE To prevent damage to the formatter board ensure the formatter board is aligned in the tracks ENWW Install memory and fonts 333 11 Reinsert the formatter pressure release tabs by squeezing them together and pushing them into place 13 If you installe
15. 0 J n addresses 2 Home button Touching this button opens the Home screen 3 From field Touch this field to open the keyboard and then type your e mail address If the system administrator has configured the device to do so this field might automatically insert a default address 4 To field Touch this field to open the keyboard and then type the e mail addresses of those whom you want to receive the scanned document 5 Subject field Touch this field to open the keyboard and then type a subject title 6 More Options button Touch this button to change certain e mail settings for the current scan job 7 Scroll bar Use the scroll bar to view and set up the CC BCC Message and File Name fields Touch any of those fields to open the keyboard and add the necessary information 8 Address book buttons Touch these buttons to use the address book to populate the To CC or BCC fields For more information see Use the local address book 9 Help button Touch this button for control panel help For more information see Use the control panel 10 Error warning button This button appears only when there is an error or warning in the status line area Touch itto open a pop up screen that will help you resolve the error or warning T 168 Chapter 12 Scan and send to e mail ENWW Perform basic e mail functions The device e mail feature offers the following
16. 166 Chapter 12 Scan and send to e mail ENWW Test the SMTP settings 1 From the Home screen touch Administration 2 Touch Initial Setup 3 Touch E mail Setup and then touch Test Send Gateways If the configuration is correct Gateways OK appears on the control panel display If the first test was successful send an e mail to yourself by using the digital send feature If you receive the e mail you have successfully configured the digital sending feature If you do not receive the e mail use these actions to resolve issues with the digital sending software e Check the SMTP and address to make sure that you typed them correctly e Printa configuration page Verify that the SMTP gateway address is correct e Make sure that the network is operating correctly Send an e mail to yourself from a computer If you receive the e mail the network is operating correctly If you do not receive the e mail contact your network administrator or Internet service provider ISP e Run the DISCOVER EXE file This program attempts to find the gateway You can download the file from the HP Web site at http www hp com support ljcm4730mfp ENWW Configure e mail settings 167 Use the Send E mail screen Use the touchscreen to navigate through the options on the Send E mail screen R o Cem 1 Send E mail button Touching this button scans the document and sends an e mail file to the provided e mail OOOO DOOOO OOOO
17. 2 3 4 5 6 On the control panel scroll to and touch Administration Touch Time Scheduling Touch Date Time Touch Date Format Touch the desired format Touch Save Set the date 1 2 3 4 5 6 On the control panel scroll to and touch Administration Touch Time Scheduling Touch Date Time Touch Date Touch the appropriate options to set the correct month date of the month and the year Touch Save Set the time format 1 2 3 4 5 6 On the control panel scroll to and touch Administration Touch Time Scheduling Touch Date Time Touch Time Format Touch the appropriate format Touch Save Set the time 1 2 3 4 ENWW On the control panel scroll to and touch Administration Touch Time Scheduling Touch Date Time Touch Time Set the real time clock 199 5 Touch the appropriate options to set the correct hour minute and AM PM setting 6 Touch Save 200 Chapter 14 Manage the MFP ENWW Configure alerts ENWW You can use HP Web Jetadmin or the MFP s embedded Web server to configure the system to alert you of problems with the MFP The alerts take the form of e mail messages to the e mail account or accounts that you specify You can configure the following e The printer s you want to monitor e What alerts are to be received for example alerts for paper jams paper out supplies status and cover open e The e mail account to which the aler
18. HP Color LaserJet CMA730 MFP User Guide ly HP Color LaserJet CMA730 MFP User Guide invent Copyright and License 2007 Copyright Hewlett Packard Development Company L P Reproduction adaptation or translation without prior written permission is prohibited except as allowed under the copyright laws The information contained herein is subject to change without notice The only warranties for HP products and Services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein Part number CB480 90939 Edition 1 04 2007 Trademark Credits Adobe Acrobat and PostScript are trademarks of Adobe Systems Incorporated Corel is a trademark or registered trademark of Corel Corporation or Corel Corporation Limited Linux is a U S registered trademark of Linus Torvalds Microsoft Windows and Windows NT are U S registered trademarks of Microsoft Corporation PANTONE UNIX is a registered trademark of The Open Group ENERGY STAR and the ENERGY STAR logo are U S registered marks of the United States Environmental Protection Agency Table of contents 1 Product basics Product comparison iios conet eec a A deus dundee naceudesanedarcetvdelaseseevecchieaedewcadadesonsedens
19. Single returms e root roe toe sd D da ende exea 321 Sheen PEUT 321 Non US returns inniti tatnen har rane e ob ado n RR eade aera aas 321 mg 321 Material restrictions lsssssesecsssseseeennenen nnnm nnnm nnn nemen nnnm ese n ern s nene ranas 321 Disposal of waste equipment by users in private households in the European Bine 322 Material Safety Data Sheet MSDS ssssssssssse eene mnes 322 For more Information x zer dore pee Bde reb c bla bo Lena a ded e ER Mc o egit 323 Certificate Orvola em 324 Bereit M MT 324 Volatile memory te ER ERR ERE Pd E Mb edited aed eee aed pees 324 Non volatile memory ariora decer rt dece ro ecce E a Ede eu Ode eX pO 324 Hard disk drive memory sssssssssseeeee eene 324 Safety Statements ie cepe heec recen TEE deduced ERR ER ERR ETE STR RRA QUERER RUE PR RR Qu 325 Laser sae y es canes aoc pi aa a it atn scuisis fa thcd sedate fads cava fet deeesspebiqinesansi ss 325 Canadian DOC regulations eterne rete rear hada n andae RO 325 VCCI statement Japan ssssssssssseeennm nenne nne nen nennen enne n nennen 325 Power cord statement Japan ssssssssssseeeneeeeenee mener nennen nenne 325 EMI statement Korea rcd oce ed bre oce obe deba Lace doa Lexar ERR d rac 325 EMI statement Talwan tee tee tct ee tede cci Meg di o re e ee e ce e d
20. The elapsed time for an update depends on the I O transfer time as well as the time that it takes for the MFP to re initialize The I O transfer time depends on a number of things including the speed of the host computer that is sending the update If the remote firmware update process is interrupted before the firmware is downloaded while Receiving Upgrade appears on the control panel display the firmware file must be sent again If power is lost during the flash DIMM update while the Performing Upgrade message appears on the control panel display the update is interrupted and the message Resend Upgrade appears in English only on the control panel display In this case you must send the upgrade by using the parallel port Finally any jobs that are ahead of the RFU job in the queue are completed before the update is processed Use FTP to upload the firmware through a browser ET NOTE The firmware update involves a change in the format of nonvolatile random access memory NVRAM Any menu settings that are changed from the default settings might return to default settings and must be changed again if you want settings that are different from the defaults 1 Print a configuration page and note the TCP IP address shown on the EIO Jetdirect page 2 Open a browser window 3 In the address line of the browser type ftp ADDRESS where lt ADDRESS gt is the address of the MFP For example if the TCP IP address is 192 168 0 90
21. This device complies with Part 15 of the FCC Rules Operation is subject to the following two Conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 1 The product was tested in a typical configuration with Hewlett Packard Personal Computer Systems 2 For regulatory purposes this product is assigned a Regulatory model number This number should not be confused with the product name or the product number s 3 All worldwide modular approvals for analog fax accessory obtained by Hewlett Packard under the regulatory model number BOISB 0308 00 incorporate the Multi Tech Systems MT5634SMI Socket Modem Module 4 The product meets the requirements of EN55022 amp CNS13438 Class A in which case the following applies Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Boise Idaho USA October 17 2006 For regulatory topics only European Contact Your Local Hewlett Packard Sales and Service Office or Hewlett Packard GmbH Department HQ TRE Standards Europe Herrenberger Stra e 140 D 71034 B blingen Germany FAX 49 7031 14 3143 USA Contact Product Regulations Manager Hewlett Packard Company PO Box 15 Mail Stop 160 Boise Idaho 83707 0015 USA Phone 208 396 6000 ENWW Declarati
22. Touch Default Copy Options Touch Staple Collate Touch Staple Touch the staple option you want to use Staple documents 133 Set the stapler at the control panel for a single copy job ET NOTE The following procedure sets the stapling option for only the current copy job 1 Scroll to and touch Copy 2 Touch Staple Collate 3 Touch the staple option you want to use Configure the device to stop or continue when the staple cartridge is empty You can specify whether the MFP stops printing when the staple cartridge is empty or if it continues printing but does not staple the jobs 1 Scroll to and touch Administration 2 Scroll to and touch Device Behavior 3 Scroll to and touch Stapler Stacker 4 Touch Staples Out 5 Touch the option that you want to use e Select Stop to stop all printing until the staple cartridge is replaced e Select Continue to continue printing jobs without stapling them Load staples Load staples if the MFP control panel display prompts you with a Stapler Low On Staples message the stapler has fewer than 20 usable staples left or a Replace Stapler Cartridge message the stapler is empty or the remaining staples cannot be used To order a replacement stapler cartridge see Part numbers The stapler accepts print jobs if it is out of staples but it does not staple the pages The printer driver can be configured to disable the staple option when the stapler cartridge is empty Use t
23. Touch the File Name field to open the keyboard pop up screen and then type the file name 9D o4 cuum Touch Send to Network Folder 174 Chapter 12 Scan and send to e mail ENWW Scan to a workflow destination ET NOTE This device feature is provided by the optional Digital Sending Software If the system administrator has enabled the workflow functionality you can scan a document and send it to a custom workflow destination A workflow destination gives you the ability to send additional information along with the scanned document to a specified network or file transfer protocol FTP location Prompts for specific information appear on the control panel display The system administrator can also designate a printer as a workflow destination which allows you to scan a document and then send it directly to a network printer for printing 1 Place the document face down on the scanner glass or face up in the ADF 2 From the Home screen touch Workflow 3 Select the destination to which you want to scan 4 In the Text Field field type the data that you want to accompany the file and then touch Send Workflow ENWW Scan to a workflow destination 175 176 Chapter 12 Scan and send to e mail ENWW 13 Fax e Analog fax e Digital fax ENWW 177 Analog fax When the analog fax accessory is installed the MFP can function as a standalone fax machine The HP Color LaserJet CM4730f MFP HP Color LaserJet CM4730fsk MFP an
24. e Select AdobeRGB for documents that use the AdobeRGB color space rather than sRGB For example some digital cameras capture images in AdobeRBG and documents that are produced with Adobe PhotoShop use the AdobeRGB color space When printing from a professional software program that uses AdobeRGB it is important that you turn off the color management in the software program and allow the printer software to manage the color space e Select None to instruct the printer to print RGB data in raw device mode To render documents properly when this option is selected you must manage color in the program in which you are working or in the operating system CAUTION Use this option only if you are familiar with the procedures for managing color in the software program or in the operating system e Select Custom Profile when you want to duplicate the printed output from other printers This setting instructs the printer to use a custom input profile to more accurately predict and control color output You can download custom profiles from www hp com Automatic or manual color adjustment The Automatic color adjustment option optimizes the neutral gray color treatment halftones and edge enhancements that are used for each element in a document For more information see Select the correct printer driver ET NOTE Automatic is the default setting and is recommended for printing most color documents The Manual color adjustment option all
25. ssse emen 266 Print quality troubleshooting tool sse mne 266 Image defect examples renatus esed d deed sland dese dee i eed de end ead s 266 Hornzontal lines or streaks Lite ert cette deed lab aathebeeartdade 266 Misaligne d Color nee ete e epatis ite een ORE 268 Vertical liries 43 15 dotted tu ebtanteatte tate 269 Repetitive defects ener ertet nnns 270 Color fade imal Colors s 2 e e e eb ebbe deret detecta 271 Color fade in one color sse 272 Fingerprints and media dents sss eene 273 LOOSEONENR EE 274 omeared toner seie ien eie eee dette a da eM DEDE E Vc ERR ETE Ve RE dd 275 White areas On page cedente pe eret enr Ie D ene ut Eve oda 276 Media damage 4 e cedar Tt edea dece ves e iii eee dece dv eda 277 Specs or stray torier x e te tna eae chee ee aac REN CHEER Red 278 Skewed stretched or off center page sss 279 Blank page ui pedet eta piden genda rues EL M Poster tee odd 280 Horizontal lities ind hte rh due ERROR n E RP ERR ERA TERCERA 281 Page SKEW a ite pital bet m ent etiam ts 282 Venica NESA 5 22 to epe Dt ep Dmm itatie i 283 Image shifted tbt tt abb e ite e c e ue 284 Unexpected image ent rait tete ete fenem trate tds 285 Calibrate the MEP mier etit Monies LL antes e ag uen ee tebe 285 Repetitive defect ruler ara ea aat o at a ea ae E nennen nene E 285 Solve fax Problem S odii rn eri e rite te aeree t la
26. 7 75 x 10 75 in v Table 7 2 Supported envelopes and postcards Size Dimensions Tray 1 mailbox Trays 2 3 4 Stapler stacker Envelope 10 105 x 241 mm 4 13 x 9 49 in v Envelope DL 110 x 220 mm 4 33 x 8 66 in v Envelope C5 162 x 229 mm 6 93 x 9 84 in v Envelope B5 176 x 250 mm 6 7 x 9 8 in v Envelope 98 x 191 mm 3 9 x 7 5 in v Monarch ENWW Supported paper and print media sizes 89 Table 7 2 Supported envelopes and postcards continued Size Dimensions Tray 1 mailbox Trays 2 3 4 Stapler stacker Post Card 100 x 148 mm 3 94 x 5 83 in v Double Post 148 x 200 mm 5 83 x 7 87 in v Card Postcard US 88 9 x 139 7 mm 3 5 x 5 5 in v Postcard 105 x 148 mm 4 13 x 5 83 in v European 90 Chapter 7 Paper and print media ENWW Custom paper sizes This product supports a variety of custom paper sizes Supported custom sizes are sizes that are within the minimum and maximum size guidelines for the product but are not listed in the supported paper sizes table When using a supported custom size specify the custom size in the print driver and load the paper in a tray that supports custom sizes ENWW Custom paper sizes 91 Special paper or print media guidelines This product supports printing on special media Use the following guidelines to obtain satisfactory results When using special paper or print media be sure to set the type and size in your print driver to obtain
27. A4 size legal size paper Executive JIS and 8 5 x 13 It can stack up to 500 sheets of paper Paper weight can range from 60 to 120 g m 16 to 32 Ib If the job consists of only one sheet or more than 30 sheets the MFP will print the job to the bin but will not staple the job It supports paper only Do not try to staple other media such as transparencies or labels The stapler staples a maximum of 20 sheets of glossy paper cardstock and HP Tough paper The printer driver must first be configured to recognize the optional stapler stacker When you want to use the stapler you must select the stapling option in the software program the printer driver or the MFP control panel Set the stapler at the control panel for printed jobs 1 2 3 4 5 6 Scroll to and touch Administration Touch Default Job Options Touch Default Copy Options Touch Staple Collate Touch Staple Touch the staple option you want to use d NOTE Selecting the stapler at the printer control panel changes the default setting to Staple It E is possible that all print jobs will be stapled However settings that are changed in the printer driver override settings that are changed at the control panel Set the stapler at the control panel for all copy jobs ENWW ET NOTE The following procedure changes the default setting for all copy jobs 1 2 3 4 5 6 Scroll to and touch Administration Touch Default Job Options
28. Alert event type Sets whether you want alerts for only critical errors or for any error including continuable errors Notification type Sets what type of alert should appear pop up message or system tray alert and e mail message Device List tab Shows information about each printer in the Devices list Printer information including printer name make and model An icon if the View as drop down box is set to Tiles which is the default setting Any current alerts for the printer If you click a printer in the list the HP Easy Printer Care software opens the Overview tab for that printer Device List tab information includes the following Find Other Printers window Allows you to add more printers to your printer list Clicking the Find Other Printers link in the Devices list opens the Find Other Printers window The Find Other Printers window provides a utility that detects other network printers so that you can add them to the Devices list and then monitor those printers from your computer HP Easy Printer Care software 189 HP Web Jetadmin software HP Web Jetadmin is a Web based software solution for remotely installing monitoring and troubleshooting network connected peripherals The intuitive browser interface simplifies cross platform management of a wide range of devices including HP and non HP printers Management is proactive allowing network administrators the ability to resolve printer issues be
29. If the computer will print directly to the MFP you can share the MFP on the network so that other network users can print to it See your Microsoft Windows documentation to enable Windows sharing Then install the MFP software on all computers that share the MFP Install the software after the parallel or USB cable has been connected If you have already connected a parallel or USB cable to a Windows computer the New Hardware Found dialog box appears when you turn on the computer 1 2 eo CU Soe m In the New Hardware Found dialog box click Search On the Locate Driver Files screen select the Specify a Location check box clear all other check boxes and then click Next Type the letter for the root directory For example X where X is the letter of the root directory on the CD ROM drive Click Next Follow the instructions on the computer screen Click Finish when installation is complete Select a language and follow the instructions on the computer screen Print a test page or a page from any software program to make sure that the software is correctly installed 60 Chapter 3 Software for Windows ENWW If installation fails reinstall the software If this fails check the installation notes and readme files on the MFP CD or the flyer that came in the MFP box or go to http www hp com support ljcm4730mfp ENWW Install the printing system software 61 Supported printer drivers Operating system PC
30. Operating environment or media in use does not meet HP specifications Troubleshooting and suggestions 1 Make sure that the environmental specifications for the device are being met 2 Printthe Print Quality Troubleshooting Pages and follow the diagnostic procedure listed on the first page to help isolate the defect to a particular component ENWW Correct print quality and copy quality problems 269 Repetitive defects Defect description Defect appear at regular intervals on the page Possible causes The device needs to be cleaned Operating environment or media in use does not meet HP specifications Troubleshooting and suggestions 1 Make sure that the environmental specifications for the device are being met 2 Print the Print Quality Troubleshooting Pages and follow the diagnostic procedure listed on the first page to help isolate the defect to a particular component 270 Chapter 16 Problem solving ENWW Color fade in all colors Defect description All colors are faded in one or more locations on the page Possible causes The device needs to be calibrated Operating environment or media in use does not meet HP specifications Troubleshooting and suggestions 1 Calibrate the MFP 2 Make sure that the environmental specifications for the device are being met ENWW Correct print quality and copy quality problems 271 Color fade in one color Defect description
31. Select the printer that you want to configure and then click Utilities Open the HP Printer Utility in Mac OS X V10 3 or Mac OS X V10 4 1 In the Dock click the Printer Setup Utility icon E NOTE Ifthe Printer Setup Utility icon does not appear in the Dock open the Finder click Applications click Utilities and then double click Printer Setup Utility 2 Select the printer that you want to configure and then click Utilities Print a cleaning page Print a cleaning page if the printer is not printing jobs at the expected quality level 1 Open the HP Printer Utility 2 Inthe Configuration Settings list select Color Cleaning 3 Click Print Cleaning Page to print the cleaning page Print a configuration page Print a configuration page to view the printer settings 1 Open the HP Printer Utility 2 Inthe Configuration Settings list select Configuration Page 3 Click Print Configuration Page to print the configuration page ENWW HP Printer Utility for Macintosh 191 View supplies status View the status of the printer supplies such as print cartridges imaging drum or print media from a computer 1 Open the HP Printer Utility 2 Inthe Configuration Settings list select Supplies Status 3 Click the Supplies tab to view the status of various replaceable supplies and click the Media tab to view the status of print media e Toview a more detailed status list click Detailed Supplies Information The Suppl
32. Table 16 7 Problems with Mac OS X The printer driver is not listed in the Print Center or Printer Setup Utility Cause Solution The printer software might not have been installed or was installed incorrectly Make sure that the printer PPD is in the following hard drive folder Library Printers PPDs Contents Resources lang lproj where lang is the two letter language code for the language that you are using If necessary reinstall the software See the getting started guide for instructions The Postscript Printer Description PPD file is corrupt Delete the PPD file from the following hard drive folder Library Printers PPDs Contents Resources lt lang gt lproj where lt lang gt is the two letter language code for the language that you are using Reinstall the software See the getting started guide for instructions The printer name IP address or Rendezvous Bonjour host name does not appear in the printer list in the Print Center or Printer Setup Utility Cause Solution The printer might not be ready Make sure that the cables are connected correctly the printer is on and the ready light is on If you are connecting through a USB or Ethernet hub try connecting directly to the computer or use a different port The wrong connection type might be selected Make sure that USB IP Printing or Rendezvous is selected depending on the type of connection that exists between the printer
33. The mylar strip is dislodged folded misinstalled or worn The ADF rollers are dirty Troubleshooting and suggestions 1 Make sure the ADF input tray guides are adjusted so that they are lightly touching the sides of the paper stack 2 Ifthe mylar strip is dislodged folded or misinstalled verify it is correctly installed If the mylar strip is worn replace it Replacement mylar strips are stored in an envelope that is underneath the white vinyl ADF backing Follow the instructions that are in the envelope 3 Clean the ADF rollers 4 Ifthe problem persists calibrate the scanner 282 Chapter 16 Problem solving ENWW Vertical lines c A CcA A A wo OOUU B UJ Cc Cc gt gt gt 00010 B Defect description Vertical lines appear on the page Possible causes The ADF is dirty Paper is stuck to the scanner glass or lid The mylar strip is dirty Troubleshooting and suggestions 1 Clean the ADF 2 Verify that no paper is on top of the scanner glass or stuck to the bottom of the scanner lid 3 Ifthe mylar strip is dirty or worn replace it Replacement mylar strips are stored in an envelope that is underneath the white vinyl ADF backing Follow the instructions that are in the envelope ENWW Correct print quality and copy quality problems 283 Image shifted AaBbCG AaBbQ AaBbQ AaBbQ AA Da r Defect description The printed image is shifted hor
34. and the computer The wrong printer name IP address or Rendezvous Bonjour host name is being used Print a configuration page in order to check the printer name IP address or Rendezvous host name Verify that the name IP address or Rendezvous host name on the configuration page matches the printer name IP address or Rendezvous host name in the Print Center or Printer Setup Utility The interface cable might be defective or of poor quality Replace the interface cable Make sure to use a high quality cable The printer driver does not automatically set up your selected printer in the Print Center or Printer Setup Utility Cause Solution The printer might not be ready Make sure that the cables are connected correctly the printer is on and the ready light is on If you are connecting through a USB or Ethernet hub try connecting directly to the computer or use a different port The printer software might not have been installed or was installed incorrectly Make sure that the printer PPD is in the following hard drive folder Library Printers PPDs Contents Resources lang lproj where lang is the two letter language code for the language that you are using If necessary reinstall the software See the getting started guide for instructions 292 Chapter 16 Problem solving ENWW Table 16 7 Problems with Mac OS X continued The printer driver does not automatically set up your selected
35. mailbox mode 298 mailbox 3 bin capacity 7 configuring 102 light status 260 models including 4 modes 297 part number 299 reattach error message 236 selecting 101 specifications physical 311 maintenance agreements 305 309 maintenance kit 299 Management menu 29 Material Safety Data Sheet MSDS 322 Media 87 media custom size Macintosh settings 126 custom size Windows settings 116 document size selecting 118 first page 116 126 loading tray 2 97 loading tray 2 3 and 4 96 loading tray 2 3 or4 94 pages per sheet 118 127 supported sizes 89 media damage 277 media damage problem solving 277 memory adding 206 329 autoconfiguration 64 enabling 338 features 5 included 2 70 insufficient 228 234 managing 206 partnumbers 300 permanent storage error messages 231 supply errors 226 Menu button 14 menu map Information menu 18 printing 182 menus control panel access denied 232 Administration 17 E mail Setup 42 Fax Setup 39 Information 18 Initial Setup 31 locking 198 Management 29 Resets 54 Send Setup 42 Service 55 Time Scheduling 27 messages alphabetical list 226 numerical list 226 types of 225 misaligned colors 268 misaligned colors problem solving 268 models features 2 monthly duty cycle 5 Index 347 multiple pages per sheet 118 127 mylar strip cleaning 217 N n up printing 118 127 Netscape Navigator versions supported embedded Web server 184 HP Web Jetadmin 190 Network Folder sc
36. paper and ledger with A3 size paper When this feature is enabled the user can select manual feed from the control panel as the paper source for a job Courier Font Regular default Select which version of the Courier font you want to use Dark Wide A4 Enabled Change the printable area of A4 size paper Disabled default If you enable this option eighty 10 pitch characters can be printed on a single line of A4 paper Print PS Errors Enabled Disabled default Select whether a PostScript PS error page is printed when the device encounters a PS error Print PDF Errors Enabled Disabled default Select whether a PDF error page is printed when the device encounters a PDF error Personality Auto default PCL PDF PS Select the printer language that the device should use Normally you should not change the language If you change the setting to a specific language the device does not automatically switch from one language to another unless specific software commands are sent to the device 46 Chapter2 Control panel ENWW Table 2 15 Device Behavior menu continued Menu item Sub menu item Sub menu item Values Description PCL Form Length Orientation Type a value between 5 and 128 lines The factory default is 60 lines Portrait default Landscape PCL is a set of printer commands that Hewlett Packard developed to provide access to prin
37. type tp 192 168 0 90 202 Chapter 14 Manage the MFP ENWW 4 5 Locate the downloaded RFU file for the MFP Drag and drop the RFU file onto the PORT1 icon in the browser window d NOTE The MFP turns off and then on automatically to activate the update When the update E process is complete a Ready message displays on the MFP control panel Use FTP to upgrade the firmware on a network connection ENWW ER o O x DW o5o09 s 11 12 13 NOTE The firmware update involves a change in the format of nonvolatile random access memory NVRAM Any menu settings that are changed from the default settings might return to default settings and must be changed again if you want settings that are different from the defaults Take note of the IP address on the HP Jetdirect page The HP Jetdirect page is the second page that prints when you print the configuration page ET NOTE Before upgrading the firmware make sure that the MFP is not in Sleep mode Also make sure that any error messages are cleared from the control panel display Open an MS DOS command prompt on your computer Type ftp TCP IP ADDRESS gt For example if the TCP IP address is 192 168 0 90 type ftp 192 168 0 90 Go to the folder where the firmware file is stored Press Enter on the keyboard When prompted for the user name press Enter When prompted for the password press Enter Type bin at the command prompt Press
38. 2 3 Open the HP Printer Utility In the Configuration Settings list select Stored Jobs Perform any of the following tasks e Toturn on the job storing function select Enable Job Storing and then click Apply Now e Toprint a stored job select a stored job in the list type the necessary personal identification number PIN in the Enter Secure Job PIN box type the number of copies that you want in the Copies To Print box and then click Print e Todelete a stored job select a stored job in the list and then click Delete HP Printer Utility for Macintosh 193 Configure trays Change the default printer tray settings from the computer 1 2 3 5 6 Open the HP Printer Utility In the Configuration Settings list select Tray Configuration In the Trays list select the tray to be configured ET NOTE To make the selected tray the default tray for printing click Make Default In the Default Media Size pop up menu select the default media size for the tray In the Default Media Type pop up menu select the default media type for the tray Click Apply Now Change network settings Change the network internet protocol IP settings from the computer You also can open the embedded Web server to change additional settings For more information see Embedded Web server 1 2 3 4 Open the HP Printer Utility In the Configuration Settings list select IP Settings Change any of the settings
39. Error Correction Mode Enabled default Disabled When Error Correction Mode is enabled and an error occurs during fax transmission the device sends or receives the error portion again JBIG Compression Enabled default Disabled JBIG compression reduces fax transmission time which can result in lower phone charges However using JBIG compression sometimes causes compatibility problems with older fax machines If this occurs turn off JBIG compression Maximum Baud Rate TCF T 30 Delay Timer Select a value from the list The default is 33 6K Default default Custom Use this feature to set the maximum baud rate for receiving faxes This can be used as a diagnostic tool for troubleshooting fax problems This setting should be left at the default value and only changed when directed by an HP technical support agent Adjustment procedures associated with this setting are beyond the scope of this guide TCF Extend Default default This setting should be left at the default value and only changed when directed by an HP Custom technical support agent Adjustment procedures associated with this setting are beyond the scope of this guide Dialing Mode Tone default Select whether the device should use tone or Pulse pulse dialing Redial On Busy Therange is between 0 and 9 The factory default is 3 times Type the number of times the device should attempt to redial if the line is
40. HP Jetdirect print server has encountered a critical error as specified by YYYY Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support ljcm47S30mfp Access denied MENUS LOCKED ACTION NOT CURRENTLY AVAILABLE FOR TRAY X TRAY SIZE CANNOT BE ANY SIZE ANY CUSTOM The control panel function that you are trying to use has been locked to prevent unauthorized access A duplexed 2 sided document was requested from a tray that is set to Any Size or Any Custom Duplexing is not allowed from a tray configured to Any Size or Any Custom Contact the network administrator Select another tray or reconfigure the tray Authentication information is incorrect Please re enter information A user name or password is incorrect Type the information again 232 Chapter 16 Problem solving ENWW Table 16 1 Control panel messages continued Control panel message Description Recommended action Authentication required Authentication has been enabled for this feature or destination A username and password are required Type the user name and password or contact the network administrator Authentication required to use this feature A user name and password are required Type the user name and password or contact the network administrator Bad duplexer connec
41. In the driver select the Stored Job option and then type a user name and job name The job does not print until someone requests it at the device control panel See Print a stored job Print a stored job ENWW At the control panel you can print a job that is stored on the device hard disk T 2 3 4 5 e From the Home screen touch Job Storage Touch the Retrieve tab Scroll to and touch the job storage folder that holds the stored job Scroll to and touch the stored job that you want to print Touch Retrieve Stored Job amp to print the document Touch the Copies field to change the number of copies to print Touch Retrieve Stored Job to print the document Job storage features 111 If the file has A lock symbol next to it the job is a private job and requires a PIN See Use the personal job feature Delete a stored job Jobs stored on the device hard disk can be deleted at the control panel 1 From the Home screen touch Job Storage Touch the Retrieve tab Scroll to and touch the job storage folder that holds the stored job 2 3 4 Scroll to and touch the stored job that you want to delete 5 Touch Delete 6 Touch Yes If the file has fi lock symbol next to it the job requires a PIN to delete it See Use the personal job feature 112 Chapter 8 Use product features ENWW 9 Print tasks e Media type and tray loading e Windows printer driver features e Macintosh print
42. Manual Settings Touch Default Gateway Touch the Default Gateway text box Use the touchscreen keyboard to type the default gateway Touch OK Touch Save Configure TCP IPv6 parameters For information about configuring the device for a TCP IPv6 network see the HP Jetdirect Print Server Administrator s Guide Disable network protocols optional Disable ENWW By factory default all supported network protocols are enabled Disabling unused protocols has the following benefits It decreases device generated network traffic It prevents unauthorized users from printing to the device It provides only pertinent information on the configuration page It allows the device control panel to display protocol specific error and warning messages IPX SPX p p m 9 p NOTE Do not disable this protocol in Windows based systems that print to the printer through IPX SPX Scroll to and touch Administration Scroll to and touch Initial Setup Touch Networking and I O Touch Embedded Jetdirect Touch IPX SPX Touch Enable Network configuration 83 7 Touch Off 8 Touch Save Disable AppleTalk 1 Scroll to and touch Administration Scroll to and touch Initial Setup Touch Networking and I O Touch Embedded Jetdirect Touch AppleTalk Touch Enable Touch Off co WO IO UU cbe a S Touch Save Disable DLC LLC 1 Scroll to and touch Administration Scroll to and touch Initial Setup Touch Networking
43. Menu item Sub menu item Sub menu item Values Description Saturday Sunday Fax Printing Fax Printing Mode Store all received If you have concerns about the security of faxes private faxes use this feature to store faxes rather than having them automatically print by Print all received creating a printing schedule faxes default For the fax printing schedule the control Use Fax Printing panel prompts you to select days and times Schedule to print faxes Change PIN Select Change PIN to change the PIN number that users must provide to print faxes 28 Chapter2 Control panel ENWW Management menu Administration Management Use this menu to set up global device management options ET NOTE default Values shown with default are the factory default values Some menu items have no Table 2 9 Management menu Menu item Sub menu item Values Description Stored Job Management Quick Copy Job Storage Limit Select the maximum number of jobs to store Use this menu to view and manage any jobs that are stored on the device Quick Copy Job Held Timeout Sleep mode Off 1 Hour 4 Hours 1 Day 1 Week Disable Use this fea
44. One color is faded in one or more locations on the page Possible causes The device needs to be calibrated Operating environment or media in use does not meet HP specifications Troubleshooting and suggestions 1 Make sure that the environmental specifications for the device are being met 2 Calibrate the MFP 3 Print the Print Quality Troubleshooting Pages and follow the diagnostic procedure listed on the first page to help isolate the defect to a particular component 272 Chapter 16 Problem solving ENWW Fingerprints and media dents Defect description Fingerprints or media dents appear on the page Possible causes Operating environment or media in use does not meet HP specifications Dents or wrinkles are from handling Troubleshooting and suggestions 1 Make sure that the environmental specifications for the device are being met 2 Make sure that the media you are using does not have any wrinkles or dents from handling and that the media is not contaminated with visible fingerprints or other foreign substances 3 Printthe Print Quality Troubleshooting Pages and follow the diagnostic procedure listed on the first page to help isolate the defect to a particular component ENWW Correct print quality and copy quality problems 273 Loose toner Defect description Toner can be rubbed off the page Possible causes Operating environment or media in use does not meet HP specifications Troubleshooting
45. PCL jobs pure text no job control Suppress Blank Pages No default Yes This option is for users who are generating their own PCL which could include extra form feeds that cause blank pages to be printed When Yes is selected form feeds are ignored if the page is blank Media Source Mapping Standard default Classic Select and maintain input trays by number when you are not using the device driver or when the software program has no option for tray selection ENWW Device Behavior menu 47 Print Quality menu Administration gt Print Quality Table 2 16 Print Quality menu Menu item Sub menu item Values Description Adjust Color Highlights Cyan Density Magenta Adjust the darkness or lightness of highlights on a Density Yellow Density printed page Lower values represent lighter highlights Black Density on a printed page and higher values represent darker highlights on a printed page 5 to 5 Default is 0 Midtones Cyan Density Magenta Adjust the darkness or lightness of midtones on a Density Yellow Density printed page Lower values represent lighter midtones Black Density on a printed page and higher values represent darker midtones on a printed page 5 to 5 Default is 0 Shadows Cyan Density Magenta Adjust the darkness or lightness of shadows on a Density Yellow Density printed page Lower values represent lighter shadows Black Density on a printed page and h
46. Printer Care SOftWate eii oett dee rede testae debere e boe eee EET 86 Other components and utilities sess e 86 iv ENWW 7 Paper and print media Understand paper and print media use ssssssssssssssssssseseeeenee enne nnn nns n nen 88 Supported paper and print media sizes 200 2 sec e eee ceeeeeececee cece eect eee ee eee aca aeaaecaeeeeeeeeeeeseteccenccaaeeeeeeeneees 89 Custom paper sizes eee cececcecce eee eose e cece ee cee ee eee eee ee ttt tE cea ee ae aeeaeeeeeeeeeee ca aaaaaaaaaeaeeeeeeeeeessedsescccneeeeeeeeeeeeess 91 Special paper or print media guidelines sss eene 92 Load paper and print media ssssssssssssssssesseseeeeeee ne rennen enne nr SEEE sinn nennen 93 Load tray A P vied 93 boad trays 25 3 o A iie eee e een inten duds rhe eue eut a HARI I REU PUER CHER FER Qe XN RR ade 94 Load standard sized media into tray 2 3 or 4 ssisssssssssssssssssss 94 Loading undetectable standard sized media into tray 2 3 and 4 96 Load custom size media into tray 2 sssssssssssee emm 97 CoOnflgure RAYS diede bsc et des uec dep teg ds pa ce gave cue ev pue exu pRdvedv p dede Er badge 98 Configure a tray when loading paper sss nennen nennen 98 Configure a tray to match print job settings ssss em 98 Configure a tray by using the Supplies Sta
47. RAM e Duplexer e Hard drive HP Color LaserJet CM4730f MFP 2 Chapter 1 Product basics ENWW The HP Color LaserJet CM4730f MFP has the same features as the base model and includes an analog fax accessory HP Color LaserJet CM4730fsk MFP The HP Color LaserJet CM4730fsk MFP has the same features as the base model and includes the following items e A Analog fax accessory e Output accessory bridge e Stapler stacker accessory HP Color LaserJet CM4730fm MFP ENWW Product comparison 3 The HP Color LaserJet CM4730fm MFP has the same features as the base model and includes the following items e Analog fax accessory e Output accessory bridge e 3 bin mailbox accessory 4 Chapter 1 Product basics ENWW Product features Functions e Two sided copying duplexing e Color digital sending e Color access control e Network printing Speed and throughput e 31 pages per minute ppm when copying and printing on letter size paper 30 ppm when copying and printing on A4 size paper e 25 to 400 scalability when using the scanner glass e 2596 to 200 scalability when using the ADF e Less than 10 seconds to print the first page e Transmit Once Raster Image Processing RIP ONCE technology e Recommended maximum monthly print volume of 85 000 pages e A 533 megahertz MHz microprocessor Resolution e 600 dots per inch dpi with Resolution Enhancement technology REt e The
48. Range Equivalent to 530 Plain or N A cardstock sheets of 75 g m unspecified standard sizes 60 g m 16 Ib 20 Ib bond bond to 120 g m 32 Ib bond Labels Maximum 0 13 mm Maximum stack Labels Side to be printed 0 005 in thick height 56 mm 2 2 on facing up inch Transparencies Minimum 0 13 mm Maximum stack Transparencies Side to be printed 0 005 in thick height 56 mm 2 2 inch on facing up 114 Chapter9 Print tasks Table 9 2 Tray 2 tray 3 and tray 4 media information continued Media type Media Media quantity Driver settings Paper orientation Output specifications Heavy 0 13 mm 0 005 Maximum stack Light glossy Side to be printed in thick height 56 mm 2 2 glossy or heavy on facing up in glossy Glossy Range Maximum stack Light glossy Side to be printed height 56 mm 2 2 glossy or heavy on facing up 75 g m 20 Ib in glossy bond to 120 g m 32 Ib bond ENWW Media type and tray loading 115 Windows printer driver features Create and use printing shortcuts in Windows Use printing shortcuts to save the current driver settings for reuse Shortcuts are available on most printer driver tabs You can save up to 25 printing shortcuts Create a printing shortcut 1 2 3 4 5 On the File menu in the software program click Print Select the driver and then click Properties or Preferences Select the print settings that you want to use Click Save As In the Printing Shortcu
49. Sensing Transparency Only default When Expanded Sensing is selected the device recognizes normal paper overhead transparencies glossy paper and tough paper When Transparency Only is selected the device recognizes only overhead transparency and non overhead transparency types ENWW Table 2 16 Print Quality menu continued Menu item Sub menu item Values Description Optimize CACOS3 In countries regions where paper is expensive this compound is added to paper to make it less expensive to produce This compound makes the paper dusty which affects print quality Background1 Background2 Registration Long Paper Pre rotation Re transfer Tray 1 Belt Contact Restore Optimize Color REt Enabled default Enable or disable Resolution Enhancement Disabled technology REt which produces print output with smooth angles curves and edges Calibration Cleaning Auto Cleaning Enabled Disabled default When auto cleaning is on the device prints a cleaning page when the page count reaches the value that is set in Cleaning Interval Cleaning Interval 1000 Set the interval when the cleaning page should be printed The interval is measured by the number of default pages printed 2000 5000 10000 20000 Auto Cleaning Size Letter Select the size of paper to use for the cleaning page A4 Process Cleaning Page Process Use this feature to create and process a cleaning page
50. Type Configuring a tray to any other type such as Bond or Glossy deactivates the media sensor in that tray The HP Color LaserJet CM4730 Series printers can automatically classify media into one of the following categories Plain Transparency Glossy Extra heavy glossy Glossy film Heavy Light Tray 1 sensing Full sensing default The printer stops at each page to sense media type This is the best mode for using mixed media in a single print job Expanded sensing ENWW Each time the printer begins a print job it stops the first page to sense the type The printer assumes that the second and all subsequent pages are of the same media type as the first page This is the second fastest mode and is useful for using stacks of the same media type Configure trays 99 Transparency e The printer does not stop any pages for sensing but distinguishes between transparencies Transparency mode and paper Normal mode e This is the fastest mode and is useful for high volume printing in Normal mode Tray 2 4 sensing Expanded sensing e The printer stops the first five pages fed from each paper tray to sense the type and averages the five results e The printer assumes that the sixth and all subsequent pages are of the same media type until the printer is turned off or goes into sleep mode or until the tray is opened Transparency only default e The printer does not stop any pages for sensing but distinguish
51. Type Selects the frame type setting for your network Auto Automatically sets and limits the frame type to the first one detected EN 8023 EN Il EN 8022 and EN SNAP Frame type selections for Ethernet networks AppleTalk Enable Off Disable the AppleTalk protocol On default Enable the AppleTalk protocol DLC LLC Enable Off Disable the DLC LLC protocol On default Enable the DLC LLC protocol Security Print Sec Page Yes default Prints a page that contains the current security settings on the HP Jetdirect print server No A security settings page is not printed Secure Web For configuration management specify whether the embedded Web server will accept communications using HTTPS Secure HTTP only or both HTTP and HTTPS HTTPS Required For secure encrypted communications only HTTPS access is accepted The print server will appear as a secure site HTTP HTTPS optional Access using either HTTP or HTTPS is permitted Firewall Specify the Firewall status on the print server Keep Firewall status remains the same as currently configured Disable Firewall operation on the print server is disabled Reset Security Specify whether the current security settings on the print server will be saved or reset to factory defaults No The current security settings are maintained Yes Security settings are reset to factory defaults Diagnostics Embedded Tests This menu provides tes
52. Utility for Macintosh 195 Security features This section explains important security features that are available for the MFP e Secure the embedded Web server e Foreign Interface Harness FIH e Secure Disk Erase e DSS authentication e Lockthe control panel menus Secure the embedded Web server Assign a password for access to the embedded Web server so that unauthorized users cannot change the MFP settings 1 Open the embedded Web server See Embedded Web server 2 Click the Settings tab 3 On the left side of the window click Security 4 Type the password next to New Password and type it again next to Verify Password 5 Click Apply Make note of the password and store it in a safe place Foreign Interface Harness FIH The Foreign Interface Harness FIH provides a portal on the MFP By using the FIH and third party equipment you can track information about copies that are made on the MFP Requirements e Windows 9X Windows Me Windows 2000 or Windows XP e X Access to third party accounting hardware solutions such as Equitrac or Copitrak devices Use the FIH To use the FIH you must download and install the FIH software The software is available from http www hp com go cljcm4730mfp software The software is used to enable or disable the FIH portal Use the software to set and change the administrator personal identification number PIN Administrators can use the PIN option to configure the
53. allow the printer software to balance lightness and darkness e SmartFocus Enhance the image quality and clarity of low resolution images such as those downloaded from the Internet Click On to allow the printer software to sharpen details in the image e Sharpness Adjust the image sharpness to your preference Click Automatic to allow the printer software to set the level of sharpening for the image e Smoothing Soften an image Click Automatic to allow the printer software to set the level of smoothing for the image Opening the HP Digital Imaging Options dialog box 1 Open the Printer Properties dialog box 2 Click the Paper Quality tab and then click the HP Digital Imaging button ET NOTE If you installed the HP Image Zone software you can use it to edit and further enhance digital photos ENWW Windows printer driver features 125 Macintosh printer driver features Create and use printing shortcuts in Macintosh Use printing shortcuts to save the current printer driver settings for reuse Create a printing shortcut 1 Onthe File menu in the software program click Print 2 Select the driver and then click Properties or Preferences 3 Select the print settings 4 Inthe Printing Shortcuts box click Save As and type a name for the shortcut 5 Click OK Use printing shortcuts 1 Onthe File menu in the software program click Print 2 Select the driver and then click Properties or Preferences 3 Inthe Pr
54. and I O Touch Embedded Jetdirect Touch DLC LLC Touch Enable Touch Off Doy MD grs or dm 059 ON Touch Save HP Jetdirect EIO print servers HP Jetdirect print servers network cards can be installed in the EIO slot Supported networking features depend on the print server model For available HP Jetdirect EIO print server models go to http www hp com go jetdirect ET NOTE Configure the card through the control panel the printer installation software or HP Web Jetadmin Refer to the HP Jetdirect print server documentation for more information 84 Chapter6 Connectivity ENWW Network utilities The device is equipped with several utilities that make it easy to monitor and manage the device on a network HP Web Jetadmin HP Web Jetadmin is a browser based management tool for HP Jetdirect connected printers within your intranet and it should be installed only on the network administrator s computer To download a current version of HP Web Jetadmin and for the latest list of supported host systems visit www hp com go webjetadmin When installed on a host server a Windows client can gain access to HP Web Jetadmin by using a supported Web browser such as Microsoft amp Internet Explorer 4 x or Netscape Navigator 4 x or later by navigating to the HP Web Jetadmin host Embedded Web server ENWW The device is equipped with an embedded Web server which provides access to information about device and netwo
55. and then from top to bottom on the second page 4 Short edge portrait This layout is often used with clipboards Every other printed image is oriented upside down Facing pages are read continuously from top to bottom Options for binding two sided printing jobs Before printing a two sided document use the printer driver to select the binding Long edge or book binding is the conventional layout used in book binding Short edge or tablet binding is the typical calendar binding ENWW Windows printer driver features 121 ET NOTE The default binding setting is to bind on the long edge when the page is set up for portrait orientation To change to long edge binding click the Flip Pages Up check box Printing booklets Some versions of the printer driver offer booklet printing settings Select binding on the left or right side on letter legal or A4 paper size Windows 2000 and XP support booklet printing for all paper sizes Manual two sided duplex printing If you want to print on two sides duplex on paper other than the supported sizes or weights for example paper heavier than 120 g m 32 Ib or very thin paper you will have to go to the MFP and reinsert the paper manually after the first side has printed AN CAUTION Do not use two sided printing when printing on labels Serious damage can result 1 Click the Windows Start button point to Settings and then click Printers and Faxes Right click
56. be fully compatible with third party and custom solutions based on PCL 5 A monochrome black only version of the HP PCL 6 driver is also available HP PostScript driver Recommended for printing with Adobe applications or other highly graphics intensive applications Best for PS level 3 needs and PS font support Slight performance benefit over PCL 6 when using Adobe applications The printer drivers include online Help that has instructions for common printing tasks and describes the buttons checkboxes and drop down lists that the driver contains Universal printer drivers The HP Universal Print Driver Series for Windows includes separate HP postscript level 3 emulation and HP PCL 5 versions of a single driver that provides access to almost any HP device while providing system administrator with tools to manage devices more effectively The Universal Print Driver is included on the device CD under the Optional Software section For more information go to www hp com go universalprintdriver Driver Autoconfiguration The HP LaserJet PCL 5 PCL 6 and PS level 3 emulation drivers for Windows 2000 Windows XP and Microsoft Vista feature automatic discovery and driver configuration for device accessories at the time of installation Some accessories that the Driver Autoconfiguration supports are the duplexing unit optional paper trays and dual inline memory modules DIMMs 64 Chapter 3 Software for Windows ENWW Automatic Configura
57. benefits e Sends documents to multiple e mail addresses saving time and delivery costs e Delivers files in black and white or in color Files can be sent in different file formats that the recipient can manipulate With e mail documents are scanned into the device memory and sent to an e mail address or multiple addresses as an e mail attachment Digital documents can be sent in several graphics formats such as TFF and JPG which allows recipients to manipulate the document file in various programs to meet their specific needs Documents arrive in near original quality and then can be printed stored or forwarded In order to use the e mail feature the device needs to be connected to a valid SMTP local area network that includes Internet access Load documents You can scan a document by using either the glass or the ADF The glass and ADF can accommodate Letter Executive A4 and A5 size originals The ADF can also accommodate Legal size originals Smaller originals receipts irregular and worn documents stapled documents previously folded documents and photographs should be scanned by using the glass Multiple page documents can be scanned easily by using the ADF Send documents The device scans both black and white and color originals You can use default settings or change the scanning preferences and file formats The following are the default settings e Color e PDF requires the recipient to have an Adobe Acrobat v
58. com support licm4730mfp 13 06 00 JAM INSIDE UPPER RIGHT There is a paper jam inside the right doors 1 Follow the onscreen instructions to find DOOR and remove the jammed media 2 Ifthe message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 226 Chapter 16 Problem solving ENWW Table 16 1 Control panel messages continued Control panel message Description Recommended action 13 09 00 JAM INSIDE FRONT SMALL DOOR 13 11 00 JAM INSIDE UPPER RIGHT DOOR There is a paper jam in the small door ofthe 1 output accessory bridge There is a paper jam in the small door of the output accessory bridge Follow the onscreen instructions to find and remove the jammed media If the message persists after clearing all pages contact HP Support at http Awww hp com support licm4730mfp Follow the onscreen instructions to find and remove the jammed media If the message persists after clearing all pages contact HP Support at http www hp com support ljom4730mfp 13 12 XX JAM IN LEFT ACCESSORY There is a paper jam in the output accessory stapler stacker or 3 bin mailbox Includes 13 12 07 13 12 08 13 12 09 13 12 10 13 12 11 Follow the onscreen instructions to find and remove the jammed media If the message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp
59. copies for a copy job copies The factory default setting is 1 Number of Sides 1 Set the default number of sides for copies 2 Color Black Color default Choose whether the default copy mode is color or black Black Auto Include Margins Off default This feature automatically reduces the image size during scanning so the margins are included On Staple Collate Staple None default Set up options for stapling and collating sets of copies One left angled If Collate is selected the device prints a complete copy before starting on the next copy Otherwise the device Collate Off prints the first page of all copies before printing the second page and so on On default Output Bin lt Binname gt Select the default output bin for copies Edge To Edge Normal recommended If the original document is printed close to the edges default use the Edge To Edge feature to avoid shadows along the edges Combine this feature with the Reduce Edge To Edge Output Enlarge feature to ensure that the entire page appears on the copies 22 Chapter 2 Control panel ENWW Default Fax Options Administration gt Default Job Options gt Default Fax Options Table 2 5 Fax Send menu Menu item Sub menu item Values Description Resolution Standard 100x200dpi Set the resolution for sent documents Higher default resolution images have more dots per inch dpi so they show more detail Lower resolution images have Fine
60. correct printer driver e Priority for print settings e Openthe printer drivers ENWW 57 Supported Windows versions Software Windows 2000 XP Server 2003 Vista Windows Installer x PCL 5 driver software x PCL 6 driver software black only x PCL 6 driver software x PostScript emulation x HP Easy Printer Care x HP Web Jetadmin x Universal Print Driver x 1 Available only on the World Wide Web You can also purchase the optional HP Digital Sending Software which provides the following advanced functionality e LAN fax e Internet fax e Windows fax e Workflow with OCR e Compatibility with Novell environments authentication folder access etc e User authentication For more information about HP Digital Sending Software and a free trial version go to http www hp com go digitalsending 58 Chapter 3 Software for Windows ENWW Install the printing system software The MFP comes with a CD that contains printer driver and installation software for Windows and Macintosh operating systems Install the printing system software to take full advantage of the MFP features If you do not have access to a CD ROM drive download the printing system software from the Internet at http www hp com support licm4730mfp Install Windows printing system software for direct connections USB or parallel This section explains how to install the printing system software for the following
61. device Device Behavior menu the next print job clears these messages Error messages communicate that some action must be performed such as adding paper or clearing a jam Some error messages are auto continuable If Auto Continue is set on the menus the device will continue normal operation after an auto continuable error message appears for 10 seconds E NOTE Pressing any button during the 10 second auto continuable error message overrides the auto continue feature and the button function takes precedence For example pressing the Stop button pauses printing and offers the option to cancel the print job Critical error messages Critical error messages inform you of a device failure Some of these messages can be cleared by turning the device off and then on These messages are not affected by the Auto Continue setting If a critical error persists service is required Control panel message types 225 Control panel messages Table 16 1 Control panel messages Control panel message Description Recommended action 10 32 00 Unauthorized Supply An unauthorized print cartridge has been 1 Install genuine HP supplies installed 2 Ifthe message persists after loading authorized cartridges contact HP Support at http www hp com support ljcm4730mfp 10 XX YY SUPPLY MEMORY ERROR The MFP cannot read or write to atleast one Reinstall the print cartridge or install a new print cartridge e label or an e lab
62. door 2 Ifthe message persists contact HP Support at http www hp com support ljom4730mfp Contact the network administrator Digital Send server is not responding Contact administrator The MFP cannot communicate with the server Verify the network connection Contact the network administrator Document feeder bin full Document feeder cover open The document feeder output bin holds 50 sheets of paper The MFP stops when the bin is full The document feeder cover is open Remove the paper from the document feeder output bin Close the document feeder cover Follow the instructions in the onscreen dialog box Document feeder pick error The document feeder experienced an error while picking media Make sure that you have not overloaded the document feeder Do not load more than 50 sheets of 20 Ib paper in the document feeder E mail Gateway did not accept the job because the attachment was too large The scanned documents have exceeded the size limit of the server Send the job again using a lower resolution smaller file size setting or fewer pages Contact the network administrator to enable sending the scanned documents by using multiple e mails E mail Gateway did not respond Job failed A gateway has exceeded the time out value Validate the SMTP IP address ENWW Control panel messages 233 Table 16 1 Control panel messages continued Control panel messag
63. feeder with the first page facing up and with the top of the page leading On the control panel touch Copy Touch Sides 158 Chapter 11 Copy ENWW 4 Touch 2 sided original 2 sided output 5 Touch OK 6 Touch Start Copy Make one sided copies from two sided documents 1 Load the documents to be copied into the document feeder with the first page facing up and with the top of the page leading On the control panel touch Copy Touch Sides Touch 2 sided original 1 sided output Touch OK o 9x de i Touch Start Copy ENWW Copy two sided documents 159 Copy mixed size originals You can copy original documents that are printed on different sizes of paper as long as the sheets of paper have one common dimension For example you could combine letter and legal sizes or you could combine A4 and A5 sizes 1 2 Arrange the sheets in the original document so they all have the same width Place the sheets face up into the document feeder and adjust both paper guides against the document From the Home screen touch Copy Touch Original Size EZ NOTE If this option is not on the first screen touch More Options until the option appears Select Mixed Ltr Lgl and then touch OK Touch Start Copy 160 Chapter 11 Copy ENWW Change the copy collation setting ENWW You can set the device to automatically collate multiple copies into sets For example if you are making two copies of three pages and
64. firmware link and follow the instructions on the Web page to download the new firmware file The file must be saved into the drive PROGRAM FILES HP WEB JETADMIN DOC PLUGINS HPWJA FIRMWARE WETDIRECT folder on the computer that is running the HP Web Jetadmin software In HP Web Jetadmin return to the main device list and select the digital sender again In the Device Tools drop down list select Jetdirect Firmware Update again On the HP Jetdirect firmware page the new firmware version is listed under Jetdirect Firmware Available on HP Web Jetadmin Click the Update Firmware Now button to update the Jetdirect firmware Upgrade the firmware 205 Manage memory This MFP supports up to 544 MB of memory 512 MB DDR plus 32 MB of additional memory on the formatter board You can add additional memory by installing dual data rate DDR memory To allow for memory expansion the MFP has two DDR slots which accept 128 or 256 MB of RAM each For information about installing memory see Install memory and print server cards The MFP features Memory Enhancement Technology MEt which automatically compresses page data to provide the most efficient use of the MFP s RAM The MFP uses DDR SODIMM Extended data output EDO DIMMs are not supported EZ NOTE If memory problems occur when you are printing complex graphics you can make more memory available by removing downloaded fonts style sheets and macros from MFP memory Reducing the co
65. firmware updates 204 Jetadmin HP Web 85 Jetdirect print server configuring 84 error messages 232 firmware updates 205 installing 340 lights 261 ENWW models including 2 settings 31 Job Mode copying 163 job storage accessing 107 features 107 personal 109 proof and hold 108 QuickCopy 110 settings 29 stored 111 K keys control panel locating 14 touchscreen 16 Korean EMI statement 325 L LAN fax 180 LAN connector 7 language control panel 224 languages printer 6 laser safety statements 325 LDAP servers connecting to 166 embedded Web server settings 186 error messages 234 validating gateway addresses 288 lights accessories 260 control panel 14 formatter 261 lines troubleshooting 281 283 link speed settings 37 links embedded Web server 187 Linux drivers 62 loading documents sizes supported 169 error messages 234 scanner glass 169 Sizes supported 169 staples 134 tray 1 93 ENWW trays 2 3 4 94 unexpected size or type error message 229 loading media configuring 93 locking control panel menus 198 loose toner 274 loose toner problem solving 274 M Macintosh AppleTalk settings 34 driver settings 67 126 drivers supported 62 drivers troubleshooting 292 problems troubleshooting 292 removing software 71 resize documents 126 software 70 software components 86 support Web sites 305 USB card troubleshooting 293 Macintosh driver settings custom size paper 126 Services tab 132 watermarks 127
66. for cleaning excess toner off the pressure roller in the fuser The process takes up to 2 5 minutes Quick Calibration Calibrate Performs partial MFP calibrations Full Calibration Calibrate Performs all MFP calibrations ENWW Print Quality menu 49 Troubleshooting menu Administration Troubleshooting ET NOTE Many of the menu items under the Troubleshooting menu are for advanced troubleshooting purposes Table 2 17 Troubleshooting menu Menu item Sub menu item Sub menu item Values Description Event Log Print This shows the event codes and their corresponding engine cycles on the control panel display Calibrate Scanner Calibrate Use this feature to compensate for offsets in the scanner imaging system carriage head for ADF and flatbed scans You might need to calibrate the scanner if it is not capturing the correct sections of scanned documents PQ Troubleshooting Print Print various diagnostic pages that help solve print quality problems Fax T 30 Trace Print T 30 Report Print or configure the fax T 30 trace report T 30 is the standard that specifies When to Print Report Never auto print handshaking protocols and error correction default between fax machines Print after any fax job Print after fax send jobs Print after any fax error Print after send errors only Print after receive errors only Fax Transmit Signal A value between 0 Set loss levels to compensate
67. for phone line Loss and 30 The defaultis signal loss Do not modify this setting unless 0 requested to do so by an HP service representative because it could cause the fax to stop functioning Fax V 34 Normal default Disable V 34 modulations if several fax failures have occurred or if phone line Off conditions require it Fax Speaker Mode Normal default A technician can use this feature technician to evaluate and diagnose fax issues by Diagnostic listening to the sounds of fax modulations Paper Path Sensors Initiate a test of the paper path sensors Diagnostic Page Print Print a diagnostic page that includes color swatches and the EP parameters table 50 Chapter2 Control panel ENWW Table 2 17 Troubleshooting menu continued Menu item Sub menu item Sub menu item Values Description Disable Cartridge Use this item to enter a mode where a Check cartridge or color pair of cartridge and drum can be removed to determine which particular color is the source of a problem In this mode all consumable related errors are ignored Paper Path Test Test Page Print Generate a test page for testing the paper handling features Define the path for the test in order to test specific paper paths Source All trays Specify whether the test page is printed from all trays or from a specific tray Tray 1 Tray 2 Additional trays are shown if applicable Destination All bins Select the output option for the test page Send th
68. humidity levels or other variables over which Hewlett Packard has no control CAUTION Using paper or print media that does not meet Hewlett Packard s specifications might cause problems for the product requiring repair This repair is not covered by the Hewlett Packard warranty or service agreements 88 Chapter 7 Paper and print media ENWW Supported paper and print media sizes This product supports a number of paper sizes and it adapts to various media ET NOTE To obtain best print results select the appropriate paper size and type in your print driver before printing Table 7 1 Supported paper and print media sizes Size Dimensions Tray 1 mailbox Trays 2 3 4 Stapler stacker Letter 216 x 279 mm 8 5 x 11 in v v v Legal 216 x 356 mm 8 5 x 14 in v v v A4 210 x 297 mm 8 27 x 11 69 in v v v Executive 184 x 267 mm 7 24 x 10 51 in v v v Executive 216 x 330 mm 8 5 x 13 in v JIS A3 297 x 420 mm 11 69 x 16 54 in A5 148 x 210 mm 5 83 x 8 27 in A6 105 x 148 mm 4 13 x 5 83 in Statement 140 x 216 mm 5 5 x 8 5 in v 11x17 279 x 432 mm 11 x 17 in 12x18 305 x 457 mm 12 x 18 in B4 ISO 250 x 353 mm 9 84 x 13 90 in B4 JIS 257 x 364 mm 10 12 x 14 33 in RA3 305 x 430 mm 12 01 x 16 93 in B5 JIS 182 x 257 mm 7 17 x 10 12 in v v B5 ISO 176 x 250 mm 6 93 x 9 84 in 8k 270 x390 mm 10 63 x 15 35 in 16k 197 x 273 mm
69. links 187 HP Instant Support Professional Edition ISPE 304 Macintosh 305 maintenance agreements 309 online 304 service dealers 305 telephone 304 D Data light locating 14 date setting 27 199 Declaration of Conformity 319 default settings Resets menu 54 defects repeating 285 delay sleep 106 ENWW device status Macintosh Services tab 132 diagnostics networks 34 digital faxing 180 digital sending about 165 169 address books 171 configuring e mail 166 control panel settings 168 embedded Web server settings 186 error messages 233 234 237 238 folders 174 job settings 173 LDAP support 166 loading documents 169 recipient lists 171 sending documents 169 Setup menu 42 SMTP support 166 troubleshooting 224 validating gateway addresses 288 workflow 175 Digital Sending tab embedded Web server 186 DIMMs dual inline memory modules installing 330 DIMMs dual inline memory partnumbers 300 Disk Erase feature 197 DLC LLC settings 34 Document feeder error messages 233 document feeder copying two sided documents 158 document feeder kit replacing 219 double sided copying 158 double sided printing error messages 232 233 downloading software 304 drivers Automatic Configuration 65 downloading 304 Macintosh 305 ENWW Macintosh settings 126 Macintosh troubleshooting 292 Services tab 125 settings 66 67 shortcuts Macintosh 126 shortcuts Windows 116 supported 62 universal 64 Windows settings 116 dup
70. might occur if an error occurred in permanent storage 1 Turn the MFP power off 2 Check that the accessory is properly seated on and connected to the MFP without any gaps between the MFP and the accessory If the accessory uses cables disconnect and reconnect them 3 Verify that there is no packaging material in or around the output device 4 Turn the MFP power on 5 If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support ljcm4730mfp Touch OK to clear the message If the message is not cleared turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http Awww hp com support licm4730mfp ENWW Control panel messages 231 Table 16 1 Control panel messages continued Control panel message Description Recommended action 68 X PERMANENT STORAGE WRITE FAIL To continue touch OK The MFP NVRAM is failing to write Printing can continue but some unexpected functions might occur if an error occurred in permanent storage Touch OK to clear the message If the message is not cleared turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support licm4730mfp 68 X STORA
71. print queue computer memory or print spooler Windows 2000 or XP delete the print job there Click Start and then click Printers Double click the device icon to open the print spooler Select the print job that you want to cancel and then press Delete If the print job is not cancelled you might need to shut down and restart the computer 136 Chapter9 Print tasks ENWW 10 Using color ENWW The HP Color LaserJet CM4730 MFP series offers great color printing as soon as you set up the MFP It provides a combination of automatic color features to generate excellent color results for the general office user plus sophisticated tools for the professional who has experience printing in color The HP Color LaserJet CM4730 MFP series provides carefully designed and tested color tables to provide a smooth accurate color rendition of all printable colors HP ImageREt 3600 Restrict color use Paper selection Color options sRGB Print in four colors CMYK CMYK ink set emulation PostScript only Color matching Manage printer color options on Windows computers Manage printer color options on Macintosh computers 137 HP ImageREt 3600 HP ImageREt 3600 print technology is a system of innovative technologies developed exclusively by HP to deliver superior print quality The HP ImageREt system sets itself apart from the industry by integrating technology advancements and optimizing each element of the print sys
72. printer m m m m where m is a value from 0 to 255 Syslog Server The IP address of the syslog server used to receive and log syslog messages Default Gateway The IP address of the gateway or router used for communications with other networks Idle Timeout The time period in seconds after which an idle TCP print data connection is closed default is 270 seconds 0 disables the timeout 32 Chapter2 Control panel ENWW Table 2 11 Jetdirect menus continued Menu item Sub menu item Sub menu item Values and Description Primary DNS Specify the IP address n n n n of a Primary DNS Server Secondary DNS Specify the IP address n n n n of a Secondary Domain Name System DNS Server IPV6 Settings Enable Use this item to enable or disable IPv6 operation on the print server Off default IPv6 is disabled On IPv6 is enabled Address Manual Settings Use this item to manually set IPv6 addresses on the print server Enable Select this item and choose On to enable manual configuration or Off to disable manual configuration Address Use this item to type a 32 hexadecimal digit IPv6 node address that uses the colon hexadecimal syntax DHCPV6 Policy Router Specified The stateful auto configuration method to be used by the print server is determined by a router The router specifies whether the print server obtains its address its configuration information or both from a DHCPV6 server
73. problem The capacity of the paper tray can vary For example if you are using 75 g m 20 Ib paper the tray holds a full ream of 500 sheets If the media is heavier the tray will not hold a full ream Do not overfill the tray NOTE If the tray is not adjusted correctly an error message might appear or the media might jam 5 Slide the tray into the MFP The MFP control panel shows the tray s media type and size If the configuration is not correct touch OK on the control panel If the configuration is correct touch Exit Loading undetectable standard sized media into tray 2 3 and 4 The following undetectable standard sized media is supported in the 500 sheet trays e Executive JIS e 85x13 e Double Japan postcard e 16K 96 Chapter 7 Paper and print media ENWW CAUTION Do not print cardstock envelopes heavy or extra heavy paper or unsupported sizes of media from the 500 sheet trays Print on these types of media only from tray 1 Do not overfill the input tray or open it while it is in use Doing so can cause paper jams Load custom size media into tray 2 To use custom media change the size setting on the control panel to Custom and set the unit of measure X dimension and Y dimension See Configure a tray to match print job settings for more information 1 Slide open the tray from the MFP 2 Continue loading the print media as described in steps 2 through 4 of the Load detectable stand
74. the sign and Off a wn Find Send Gateways Search the network for SMTP gateways that the device can use to send e mail SMTP Gateway Enter a value Specify the IP address of the SMTP gateway that is used to send e mail from the device Test Send Gateway Test the configured SMTP gateway to see if it is functional Send Setup menu Administration gt Initial Setup gt Send Setup Table 2 14 Send Setup menu Menu item Values Description Replicate MFP Enter a value IP Address Copy the local Send settings from one device to another Allow Transfer to New DSS Off Use this feature to allow the transfer of the device from one HP Digital Sending Software DSS server to another On default HP DSS is a software package that handles digital sending tasks such as faxing e mail and sending a scanned document to a network folder Allow Use of Digital Send Service Off This feature allows you to configure the device for use with an HP Digital Sending Software DSS server On default Fax Number Confirmation Disable default When fax number confirmation is enabled you are prompted to enter the fax number twice to verify that it has been typed correctly Enable 42 Chapter2 Control panel ENWW Device Behavior menu Administration gt Device Behavior Table 2 15 Device Behavior menu Menu item Sub menu item Sub menu item Values Description Language Select the language from the lis
75. the MFP or if the tray is not adjusted correctly Reload the tray with the correct media size Reconfigure the size in a tray so that the MFP will use a tray that contains the size required for the print job Follow the instructions in the onscreen dialog box 41 3 LOAD TRAY XX lt TYPE gt lt SIZE gt To use another tray touch OK The specified tray is loaded with media that is longer or shorter in the feed direction than the size adjusted for the tray Touch OK to use another tray Reconfigure the size in a tray so that the MFP will use a tray that is loaded with the size of media required for the print job If the message does not clear automatically from the control panel display turn the MFP off and then turn the MFP on 41 X ERROR To continue touch OK A temporary printing error occurred Touch OK to clear the error If the error is not cleared turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http Awww hp com support licm4730mfp 49 XXXXX ERROR To continue turn off then on A critical firmware error has occurred Remove third party devices Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See ENWW Control panel messages 229 Table 16 1 Control panel messages continued Control panel message Des
76. the best print results CAUTION HP LaserJet printers use fusers to bond dry toner particles to the paper in very precise dots HP laser paper is designed to withstand this extreme heat Using inkjet paper not designed for this technology could damage your printer Media type Do not Envelopes Store envelopes flat Use envelopes where the seam extends all the way to the corner of the envelope Use peel off adhesive strips that are approved for use in laser printers Do not use envelopes that are wrinkled nicked stuck together or otherwise damaged Do not use envelopes that have clasps snaps windows or coated linings Do not use self stick adhesives or other synthetic materials Labels Use only labels that have no exposed backing between them Use Labels that lie flat Use only full sheets of labels Do not use labels that have wrinkles or bubbles or are damaged Do not print partial sheets of labels Transparencies Use only transparencies that are approved for use in laser printers Place transparencies on a flat surface after removing them from the product Do not use transparent print media not approved for laser printers Letterhead or preprinted forms Use only letterhead or forms approved for use in laser printers Do not use raised or metallic letterhead Heavy paper Use only heavy paper that is approved for use in laser printers and meets the wei
77. the output device If it is flashing or amber see the Problem Solving chapter of this document Reinstall Output Device The output device has been removed or is not attached Make sure the output bin 3 bin mailbox or stapler stacker is correctly installed on the MFP Remove All Print Cartridges The MFP is executing a component test and the component selected is Belt Only Remove all print cartridges Remove At Least One Print Cartridge Replace lt color gt Cartridge The MFP is executing a disable cartridge check or component test where the component selected is the cartridge motor The identified print cartridge has reached the end of life Printing can continue Remove one print cartridge Replace the specified color cartridge REPLACE DIMM lt X gt MEM TEST FAILURE The listed DIMM is not functioning properly and must be replaced Replace the DIMM Replace Fuser Kit The fuser is nearing the end of its useful life Printing can continue Replace the fuser kit 1 Open the right side covers 2 Use the green handle to lift the fuser cover 3 Grasp the purple handles on the fuser unit 4 Remove the old fuser unit from the MFP 5 Install the new fuser unit 6 Close the top cover Replace staple cartridge The stapler is out of staples Replace the staple cartridge Replace Supplies If the device is configured to stop at out and multiple print cartridge
78. the tray Close the tray if you are using tray 2 3 or 4 The tray configuration message appears Touch OK to accept the detected size or touch Modify to choose a different paper size If modifying the tray configuration select the size ET NOTE The MFP automatically detects most media sizes in trays 2 3 and 4 If modifying the tray configuration select the paper type Touch Exit Configure a tray to match print job settings 1 2 In the software program specify the source tray the paper size and the paper type Send the job to the MFP If the tray needs to be configured the LOAD TRAY X message appears If the highlighted size is not correct touch X MILLIMETERS Then use the numeric keypad to set the X and Y dimensions If the highlighted paper type is not correct touch Paper Handling and select the paper type Touch OK Touch Exit 98 Chapter7 Paper and print media ENWW Configure a tray by using the Supplies Status menu You can also configure the trays for type and size without a prompt from the MFP 1 2 3 4 5 6 Scroll to and touch Supplies Status Touch the desired tray Touch Modify Select the size and type If you select a custom type use the numeric keypad to set the X dimension and the Y dimension and then touch OK Touch OK Touch OK again Automatic media type sensing auto sense mode The automatic media type sensor functions only when that tray is configured to Any
79. to e mail Configure E mne 166 Supported protocols sssssssssssssssssssesessenene eene nnne err ters nennen innen nennen rennes 166 Configure e mail server settings ssssssseeenm emm enne 166 Use the Send E mail Screen seirinin aaa dadeaaagadvvssaaadadadantaadeardavadinasen 168 Perform basic e mail functions cece eeeeccecce eee ee eee eee cece cea eeaaeaaeeeeeeeeeeeeeeeeeesetccecencaaeeeeeeseeeeeeeseeieees 169 Load documienls ttt tete dite eed ex aede ex e natae aaia 169 Send COCUMOENMS EET 169 SENG a doc ment sariani aa iaa a a a a aaia aA 169 Use the auto complete function ssssssse HH 170 Use the address DOOR etat tee e e eR Paden cade AER ERU TRE ee E THERE AREE ERa AE du 171 Create a recipient list sss nenmeemnnrere ener nennen nennen nnn nennen renes 171 Use the local address BOOK ceret rinde tt rate rhe E 171 Add e mail addresses to the local address book ssseeeuusesuussse 172 Delete e mail addresses from the local address book ssuus 172 Change e mail settings for the current job ssssssseeenn emnes 173 tenor 174 Scan to a workflow destination cccceceeeeeceeceeccaeceeceeeeeeeeeeee sce caaaaaecaeeeeeeeeeeeeeesseseeceecsansaeeeeeeeeess 175 13 Fax Pure ng
80. two sided printing option appears select the appropriate settings in the printer driver software including the page and binding orientation Automatic two sided printing is not supported for certain media types e Transparencies e Envelopes e Labels e Heavy extra heavy cardstock and HP Tough paper The maximum weight paper for automatic duplex printing is 120 g m 32 Ib bond Automatic two sided printing only supports the following media sizes e Letter e Legal e B5 e Executive e 8 5 x 13 e A4 Manual two sided printing can support all sizes and more types of media excluding transparencies envelopes and labels If both automatic and manual two sided printing are enabled the MFP will automatically print on two sides if the duplexer supports the selected size and type Otherwise manual duplex will be enabled For best results avoid using rough textured heavyweight media when duplexing When using special media such as letterhead or forms place the media face down in tray 2 3 or 4 with the logo to the left Place special media face down in tray 1 with the logo feeding into the MFP last 128 Chapter 9 Print tasks ENWW Enable or disable automatic two sided printing from the control panel If you cannot adjust two sided printing settings in your software program or printer driver adjust them on the control panel The factory default setting is 1 sided AN CAUTION Do not use two sided printing whe
81. use the information in this section to resolve the problem Solve network printing problems ET NOTE HP recommends that you use the MFP CD to install and set up the MFP on a network Make sure that the network cable is securely seated into the MFP s RJ45 connector Make sure that the Link LED on the formatter is lit See Understand lights on the formatter Make sure that the I O card is ready Print a configuration page see Information pages If an HP Jetdirect print server is installed printing a configuration page also prints a second page that shows the network settings and status ET NOTE The HP Jetdirect print server supports various network protocols TCP IP IPX SPX Novell NetWare AppleTalk and DCL LLC Make sure that the correct protocols and network parameters are set correctly On the HP Jetdirect configuration page verify the following items for your protocol e Under HP Jetdirect Configuration the status is I O Card Ready e Protocol status is Ready e An IP address is listed e The configuration method Config by is listed correctly See the network administrator if you are not sure which method is correct Try printing the job from another computer To verify that a MFP works with a computer use a parallel cable to connect it directly to a computer You will have to reinstall the printing software Print a document from a program that has printed correctly in the past If this works a
82. will be lost You might want to add more memory to the MFP if you print complex graphics or PS documents or if you use many downloaded fonts Additional memory also allows the MFP to print multiple collated copies at the maximum speed ET NOTE Single in line memory modules SIMMs dual in line memory modules DIMMs used on previous HP LaserJet printers are not compatible with the MFP Before ordering additional memory see how much memory is currently installed by printing a configuration page 329 Install memory and fonts You can install more memory for the MFP and you can also install a font card to allow the MFP to print characters for languages such as Chinese or the Cyrillic alphabet CAUTION Static electricity can damage DIMMs When handling DIMMs either wear an antistatic wrist strap or frequently touch the surface of the DIMM antistatic package and then touch bare metal on the MFP Install DDR memory DIMMs 1 Turn the MFP off 2 Disconnect all power and interface cables 330 Appendix E Install memory and print server cards ENWW 3 Locate the gray formatter pressure release tabs on the formatter board in the rear of the MFP 4 Gently squeeze the tabs and pull them out of the formatter 5 Gently pull on the black tabs to pull the formatter board from the MFP Place the formatter board on a clean flat grounded surface J TD o EUM S D s Gi
83. 10 Mbps Full duplex operation 100TX Half 100 Mbps half duplex operation 100TX Full 100 Mbps full duplex operation ENWW Initial Setup menu 37 Table 2 11 Jetdirect menus continued Menu item Sub menu item Sub menu item Values and Description 100TX Auto Limits auto negotiation to a maximum link speed of 100 Mbps 1000TX Full 1000 Mbps full duplex operation Use this item to print a page that lists the configuration of the following protocols IPX SPX Novell NetWare AppleTalk DLC LLC Print Protocols 38 Chapter2 Control panel ENWW Fax Setup Administration gt Initial Setup gt Fax Setup Table 2 12 Fax Setup menu Menu item Sub menu item Sub menu item Values Description Required Settings Country Region Countries regions Configure the settings that are legally listed required for outgoing faxes Date Time Fax Header Phone Number Information Company Name PC Fax Send Disabled Use this feature to enable or disable PC Fax Send PC Fax Send enables users to send Enabled default faxes through the device from their computers if they have the Send Fax driver installed ENWW Initial Setup menu 39 Table 2 12 Fax Setup menu continued Menu item Sub menu item Sub menu item Values Description Fax Send Settings Fax Dial Volume Off Low default High Use this feature to set the volume of the tones that you hear while the device dials the fax number
84. 13 13 00 JAM INSIDE RIGHT DOORS There is a paper jam in the right side of the MFP Follow the onscreen instructions to find and remove the jammed media If the message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 13 20 00 JAM IN TRAY X There is a paper jam in the paper tray indicated Follow the onscreen instructions to find and remove the jammed media If the message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 13 20 00 JAM INSIDE RIGHT DOORS There is a paper jam in the right side of the MFP Follow the onscreen instructions to find and remove the jammed media If the message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 13 21 00 JAM IN TRAY X There is a paper jam inside the upper right door or inside the fusing unit Follow the onscreen instructions to find and remove the jammed media If the message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp ENWW Control panel messages 227 Table 16 1 Control panel messages continued Control panel message Description Recommended action 13 30 00 JAM INSIDE DRAWER BELOW TRAY 1 13 31 00 JAM INSIDE UPPER RIGHT DOOR There is a paper jam inside the lower right door There is a paper jam inside the upper r
85. 162 Chapter 11 Copy ENWW Combine copy jobs by using Job Build Use the Job Build feature to build a single copy job from multiple scans You can use either the document feeder or the scanner glass The settings for the first scan are used for subsequent scans ENWW 1 2 3 4 5 6 7 EZ Touch Copy Scroll to and touch Job Build Touch Job Build On Touch OK If necessary select the desired copy options Touch Start Copy After each page is scanned the control panel prompts you for more pages If the job contains more pages load the next page and then touch Start Copy If the job contains no more pages touch Finished to print NOTE In Job Build if you scan the first page of a document by using the document feeder then you must scan all of the pages in that document by using the document feeder If you scan the first page of a document by using the scanner glass then you must scan all of the pages in that document by using the scanner glass Combine copy jobs by using Job Build 163 Cancel a copy job To cancel the copy job that is currently running touch Stop on the control panel This pauses the device Then touch Cancel Current Job E NOTE If you cancel a copy job clear the document from the flatbed scanner or from the automatic document feeder 164 Chapter 11 Copy ENWW 12 ENWW Scan and send to e mail The MFP offers color scanning and digital sending capabilities By using the contro
86. 2 HP Color LaserJet CM4730 MFP sessseseeeeeene n menn nnn n nnn nnne nnn rss n nar nn nnne 2 HP Color LaserJet CM4730f MFP ccesecccceceseeetecesseeeeeceaseeeeeceeseeeeaneaseeesaneaseeeeaneeseeees 2 HP Color LaserJet CM4730fsk MEP cccccccescssseeceeceaseeeceeeeaeessceeeecsaeeceeeeaneaeeeeeataseeees 3 HP Color LaserJet CM4730fm MFP cccccccceeeececceseeeceeceasesceeceaeeeceeeeaneeeeecsaeeeeersaneeees 3 Product features oct nette t aperi aeree a a ident r evi caer cute rt rebut adeb 5 Product walkaround cceeeccceeceesecececceaneesecceeaeeeeeeeeeceaueeeeeeeeaneaseceeeceauaeseeeeeaueaseeseeaeaaaeeeeeseeaeanseseeeeea 9 Front VIEW ctsnensc nud LII uM M 9 BICK VIEW MP 10 Interface POMS Ji ere re erre ee er nae repa eru AE EE FE EE HEX nU Us eee 11 Serial number and model number location sssseeessseeee 11 2 Control panel ENWW Use the control panel ccccccceccee cee ee eee e eee eeee te ce aaa aaeaaeaaecaeeceeeeeeeeeeeeeeeeeeeetgeasaasaeaeaaeaaecaeeeeeeeeeeeeenenes 14 Control panel layout 1 2 2 tart racer iac eee niae E E XE YRREIe 14 neuere R 15 Buttons on the touchscreen osinean a enne EAEE nnn nn nennen 16 Control panel help System cete tur ta eaa een a a due d eu RU eda aO dx 16 Navigate the Administration menu ssssssssseseseseeneee enne nennen nnne innen nnne renes 17 Inforrmatlor
87. 200x200dpi fewer dots per inch and show less detail but the file size is smaller Superfine 300x300dpi Fax Header Prepend default Select the position of the fax header on the page default Select Prepend to print the fax header above the fax content and move the fax content down on the page Overlay Select Overlay to print the fax header over the top of the fax contents without moving the contents down Using this option could prevent a single page fax from flowing onto another page Table 2 6 Fax Receive menu Menu item Values Description Forward Fax Fax Forwarding To forward received faxes to another fax device select Fax Forwarding and Custom Then type the number of the other fax Change PIN device into the Fax Forwarding Number field When you select this menu item for the first time you are prompted to set up a PIN Type that PIN every time you use this menu This is the same PIN that is used to access the Fax Printing menu Stamp Received Faxes Enabled Add the date time senders phone number and page number to each page of the faxes that this device receives Disabled default Fit to Page Enabled default Shrink faxes that are larger than Letter size or A4 size so that they can fit onto a Letter size or A4 size page If it this feature set to Disabled Disabled faxes larger than Letter or A4 will flow across multiple pages Fax Paper Tray Select from the list of trays Select the tray that holds the si
88. 3 V10 4 and Print Print menu click Applications later 2 Change the settings that 2 you want on the various pop up menus Change the settings that you want on the various pop up menus On the Presets pop up menu click Save as and type a name for the preset These settings are saved in the Presets menu To use the new settings you must select the saved preset option every time you open a program and print ENWW Open the printer drivers Open Utilities and then open Print Center Mac OS X V10 2 Printer Setup Utility Mac OS X V10 3 or Mac OS X V10 4 Click on the print queue On the Printers menu click Show Info Click the Installable Options menu ET NOTE Configuration settings might not be available in Classic mode 67 68 Chapter 3 Software for Windows ENWW 4 Software for Macintosh e Software for Macintosh computers e Remove software from Macintosh operating systems ENWW 69 Software for Macintosh computers The HP installer provides PostScript Printer Description PPD files Printer Dialog Extensions PDEs and the HP Printer Utility for use with Macintosh computers For network connections use the embedded Web server EWS to configure the device See Embedded Web server The printing system software includes the following components e PostScript Printer Description PPD files The PPDs in combination with the Apple PostScript printer drivers p
89. 5 8 Bels A 58 dB A Sound pressure level Declared per ISO 9296 Printing Lpam 50 dB A Copying Lpam 52 dB A Ready Lpam 37 dB A 1 Values subject to change See hittp www hp com support licm4730mfp for current information 2 HP Color LaserJet CM4730 MFP series speed is 30 ppm A4 size Configuration tested HP Color LaserJet CM4730 MFP Base model simplex printing with A4 paper size 3 Configuration tested HP Color LaserJet CM4730 MFP Base model simplex copying from ADF with A4 paper size 314 Appendix C MFP specifications ENWW Environmental specifications Environmental condition Recommended Allowed Storage standby Temperature MFP and print 17 to 25 C 62 6 to 77 F 15 to 30 C 59 to 86 F 20 to 40 C 4 to 104 F cartridge Relative humidity 30 to 70 relative humidity 10 to 80 RH 10 to 90 RH Altitude N A 0 meters 0 feet to 2600 N A meters 8530 feet ENWW Environmental specifications 315 316 Appendix C MFP specifications ENWW D Regulatory information ENWW 317 Compliance with FCC regulations This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installe
90. 730f CM4730fm and CM4730fsk MFP models Optional HP Digital Sending Software DSS Optional enhanced input output EIO cards USB 2 0 ACC port accessory port with USB host capabilities Accessory port for connecting third party devices Environmental features Security features FIH ENWW Sleep setting saves energy meets ENERGY STAR guidelines Version 1 0 Secure Disk Erase Security lock Job retention DSS authentication Windows user authentication LDAP authentication Product features 7 e Group PIN authentication Group 1 and Group 2 e User PIN authentication 8 Chapter 1 Product basics ENWW Product walkaround Front view ENWW ADF top cover 2 Automatic document feeder ADF input tray for copy scan fax originals 3 Control panel status lights 4 Control panel display with touch screen functionality 5 Control panel keypad 6 Right side covers provides access to the print cartridges and other consumables 7 Tray 2 3 and 4 8 Paper level indicators 9 On Off switch 10 Output bin 11 Scanner lock Product walkaround 9 Back view 1 Output bin 2 Interface ports 3 On off switch 4 Power connection 10 Chapter 1 Product basics ENWW Interface ports The MFP has five ports for connecting to a computer or a network The ports are at the left rear corner of the MFP
91. Care Select one of the following options Windows Click Start click Settings and then click Printers or Printers and Faxes Double click HP Color LaserJet CM4730 MFP or Mac OS X Open Print Center or Printer Setup Utility for Mac OS X v 10 3 and double click the line for the HP Color LaserJet CM4730 MFP Verify that you have installed the HP Color LaserJet CM4730 MFP series printer driver Check the program to make sure that you are using an HP Color LaserJet CM4730 MFP series printer driver 222 Chapter 16 Problem solving ENWW 8 Print a short document from a different program that has worked in the past If this solution works then the problem is with the program you are using If this solution does not work the document does not print complete these steps a Try printing the job from another computer that has the MFP software installed b If you connected the MFP to the network connect the MFP directly to a computer with a parallel cable Redirect the MFP to the correct port or reinstall the software selecting the new connection type that you are using 9 If the problem is still not resolved see Determining MFP problems ENWW Solving general problems 223 Determining MFP problems Situation Message The control panel display is blank and internal fans are not running Solution Make sure that the MFP power is on Press all the keys to see if one is stuck Contact your HP authorized servic
92. Destination 102 mm 4 inches 51 mm 2 inches For envelopes of other sizes adjust the margin settings appropriately Load trays 2 3 or 4 Trays 2 3 and 4 each hold up to 500 sheets of standard paper or a 50 8 mm 2 inch stack of labels Tray 2 stacks above the other 500 sheet trays Load standard sized media into tray 2 3 or 4 The MFP automatically detects the following standard sizes of media in these 500 sheet trays letter legal executive A4 A5 and JIS B5 The following undetectable standard size media sizes are not marked in the trays but are listed in the Size menu for each tray 8 5 x 13 Executive JIS double Japan postcard and custom A CAUTION Do not print cardstock envelopes heavy or extra heavy paper or unsupported sizes of media from the 500 sheet trays Print on these types of media only from tray 1 Do not overfill the input tray or open it while it is in use Doing so can cause jams in the MFP 1 Slide the tray from the MFP M Ed 94 Chapter7 Paper and print media ENWW 2 Adjust the rear media length guide by squeezing the guide adjustment latch and sliding the back of the tray to the length of the media you are using ENWW Load paper and print media 95 4 Load media into the tray face up ET NOTE For best performance fill the tray completely without splitting the ream of paper Splitting the ream can cause a multifeed
93. E UTAM 54 Senice men RE EERE T E 55 3 Software for Windows Supported Windows versions ssssssssssssssseseee eene menn s nnne nennen nennen EEEE nnne 58 Install the printing system software uessessiesese eene ceci nna cce tana dod a nnn a daa do tasa da aa 59 Install Windows printing system software for direct connections USB or parallel 59 Install Windows printing system software for networks sse 59 Use Windows sharing on a network ssssssseeee nennen errem 60 Install the software after the parallel or USB cable has been connected 60 Supported printer drivers sssssssssssssssssssssseneeneennen ennemi emen ennt nn nennen nn nennen SEERE EEEE 62 Remove software for Windows cccccccceeeeeeeeeceeeeeaeeeeeeeee cette enne enmemrtn nnne nnns nnne n nene nrrer trs sensn sitne 63 Select the correct printer driver ssssssssssssssssssseseneneneneee eene nennen nennen 64 Universal printer drivers eere iran eee haare Pr n aae Dore ERR R edo eye DURER POR SER EIE Apr nd 64 Driver Autoconfiguration ssssssssssseeeenne eene emnes 64 Automatic Configuration sensisse eene nennen nennen nennen nennen nns 65 Priority rore euo M 66 Open the printer drivers essere enne ner nrrr sensn enne sensn nennt nensis nns 67 4 Software for Mac
94. EE Ie nus 224 Control panel message types ssssssssessssseeenee eee nett eer enne enne nnn nennen nennen enn nene 225 Gontrol panel messages iced dedisti deret bL Log ee ee E E Eee b ERE ede cee 226 SUI CE 239 Jam recovery caccari 240 Clear jams behind the right covers scssisesrisiiriniirsicieisr ienie emen 241 Clear Jaris ln tray T ios E S 246 Clear Jams In tray 2 3 OF 4 iier ter ee MERI REM e dd IHR ROC Uc Man aaae aa 246 Clear jams in the stapler stacker sssssssssesseee en ene 248 Clear Staple Jam tt etie cde cde edet edle De e te bru edes cede 249 Clear jams in the 3 bin mailbox sseenm emm emer 250 Clear jams in the output accessory bridge sssssseem 253 Clear jams in the ADF sic csccisccdeatcesaeeceteecviyicese thse ceaeennaaecdeetasagectaeeeegnecaeetasagecddeeenencedeereaee 254 Media handling problems c 256 Printer feeds multiple Sheets ccccccceceeeeeeeeeeeeeeeeeee cece eeaeeeaeaaaaeaaaeaaeeaecaeecaeeeeeeeeeeees 256 Printer feeds incorrect page SIZE 6 scccccceeceseneeccesseeeceeneceeedeenceaceesdedecnenaceenegenneedartenveneees 256 Printer pulls from incorrect tray sssssssseeeennem eene nnns 256 Media does not feed automatically ssssseene nnne 257 Media does not feed from tray 2 3 or 4 ssseessssssssssssssssssse 257 Transparencies or glossy paper will not feed
95. ENWW Use the stored job feature You can save a print job to the device hard disk without printing it You can then print the job at any time at the device control panel For example you might want to download a personnel form calendar time sheet or accounting form that other users can print when they need it You also can create a stored copy job at the device control panel that can be printed at a later time Create a stored copy job 1 2 3 4 Place the original document face down on the glass or face up in the ADF From the Home screen touch Job Storage Touch the Create tab Specify the name for the stored job in one of these ways e Select an existing folder from the list Touch New Job and type a job name e Touch the box below the existing Folder Name or Job Name on the right hand side of the screen and then edit the text A private stored job has a lock icon next to the name and it requires that you specify a PIN to retrieve it To make the job private select Make Job Private and then type the PIN for the job Touch OK Touch More Options to view and change other job storage options After all the options are set touch Create Stored Job in the upper left corner of the screen to scan the document and store the job The job is saved on the device until you delete it so you can print it as often as necessary For information about printing the job see Print a stored job Create a stored print job
96. Enter The message 200 Types set to I Using binary mode to transfer files appears in the command window Type put and then the file name for example if the file name is CM4730mfp efn type CM4730mfp efn The download process begins and the firmware is updated on the MFP This can take approximately five minutes Let the process finish without further interaction with the MFP or computer ET NOTE The MFP automatically turns off and then on again after processing the upgrade At the command prompt type bye to exit the ftp command At the command prompt type exit to return to the Windows interface Upgrade the firmware 203 Use HP Web Jetadmin to upgrade the firmware This procedure requires that you install HP Web Jetadmin Version 7 0 or later on your computer See HP Web Jetadmin software Complete the following steps to update a single device through HP Web Jetadmin after downloading the RFU file from the HP Web site d 2 Start HP Web Jetadmin Open the Device Management folder in the drop down list in the Navigation panel Navigate to the Device Lists folder Expand the Device Lists folder and select All Devices Locate the MFP in the list of devices and then click to select it If you need to upgrade the firmware for multiple HP Color LaserJet CM4730 MFP series MFPs select all of them by pressing the Ctrl key as you click the name of each MFP Locate the drop down box for Device Tools in the upper rig
97. FIH to prevent any unauthorized changes Changes can be made only with the correct PIN authentication ET NOTE Itis important to remember the PIN that is assigned to the FIH administration software The PIN is required to make any changes to the FIH Enable the FIH portal 1 Double click the FIH EXE file The Foreign Interface Harness dialog box appears 2 Click OK 196 Chapter 14 Manage the MFP ENWW Click Enable If you have not entered a PIN before click No If you have entered a PIN before click Yes If you click No type and confirm the PIN and then click OK If you click Yes type the PIN and click OK E NOTE The PIN must be numeric Click the appropriate button for the type of connection Direct or Network If Direct is selected type the MFP port If Network is selected type the IP address and port for the MFP ET NOTE The IP address for the MFP can be found on the Configuration page If you typed an incorrect IP address you will receive an error message Otherwise the portal is enabled Disable the FIH portal 1 2 3 4 5 B Double click the FIH EXE file The Foreign Interface Harness dialog box appears Click OK Click Disable Type the PIN and click OK Click the appropriate button for the type of connection Direct or Network If Direct is selected type the MFP port and click OK If Network is selected type the IP address and port for the MFP and then click OK The portal is dis
98. GE ERROR SETTINGS CHANGED To continue touch OK One or more MFP settings are invalid and have been reset to the factory default settings Printing can continue but some unexpected functions might occur if an error occurred in permanent storage Touch OK to clear the message If the message is not cleared turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support ljcm47S30mfp 69 X ERROR To continue turn off then on A temporary printing error occurred Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support ljcm47S30mfp 79 ERROR To continue turn off then on A critical hardware error occurred Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support licm4730mfp 8X YYYY EIO ERROR The EIO accessory card has encountered a critical error as specified by YYYY Try the following actions to clear the message 1 Turn the MFP off and then turn the MFP on 2 Tum the MFP off reseat the EIO accessory and then turn the MFP on 3 Replace the EIO accessory 8X YYYY EMBEDDED JETDIRECT ERROR The embedded
99. HP Easy Printer Care Software using 188 HP Easy Printer Care software using 188 208 HP fraud hotline 207 HP Instant Support Professional Edition ISPE 304 HP Jetdirect print server configuring 84 error messages 232 firmware updates 205 installing 340 lights 261 models including 2 settings 31 HP Jetdirect print servers installing 340 HP Printer Utility Macintosh 70 HP Universal Print Driver 64 HP Web Jetadmin browsers supported 190 checking toner level 208 downloading 190 firmware updates 204 HP Authorized Dealers 305 humidity requirements 208 315 l I O configuration network configuration 81 settings 31 image fuser kit 110 volt part number 299 image fuser kit 220 volt part number 299 image transfer ETB kit part numbers 299 Information menu 18 information pages 182 Information tab embedded Web server 185 Initial Setup menu 31 insert tray error messages 234 install cartridge error message 234 installers Windows 86 installing EIO cards 340 insufficient memory 228 234 interface ports included 7 locating 11 internal clock errors 226 Internet Explorer versions supported embedded Web server 184 HP Web Jetadmin 190 Internet fax 180 IP address changing 81 Macintosh troubleshooting 292 IPX SPX setting 34 83 ISPE HP Instant Support Professional Edition 304 J jam access lever locating 9 jams envelopes 258 recovery 240 Japanese VCCI statement 325 Jetadmin browsers supported 190 downloading 190
100. HP Web Jetadmin through a supported Web browser such as Microsoft Internet Explorer 5 5 and 6 0 or Netscape Navigator 7 0 HP Web Jetadmin has the following features The task oriented user interface provides configurable views saving network managers significant time The customizable user profiles let network administrators include only the function viewed or used Instant e mail notification of hardware failure low supplies and other MFP problems Installation and management can be conducted from anywhere through a standard Web browser Advanced autodiscovery locates peripherals on the network without manually entering each printer into a database Integration into enterprise management packages is easy Quickly find peripherals based on parameters such as IP address color capability and model name Easily organize peripherals into logical groups with virtual office maps for easy navigation Manage and configure multiple printers simultaneously To download a current version of HP Web Jetadmin and to see the latest list of supported host systems visit HP Customer Care Online at http www hp com go webjetadmin 74 Chapter5 Software for other operating systems ENWW UNIX The HP Jetdirect Printer Installer for UNIX is a simple printer installation utility for HP UX and Solaris networks It is available for download from HP Customer Care Online at http www hp com support net printing NOTE Sample model scrip
101. L 5 PCL 6 PS level 3 emulation Windows v v v Mac OS X V10 2 and later v Linux v 1 For Linux download the postscript level 3 emulation driver from www hp com go linuxprinting The printer drivers include online Help that has instructions for common printing tasks and also describes the buttons checkboxes and drop down lists that are in the printer driver 62 Chapter 3 Software for Windows ENWW Remove software for Windows 1 Click the Windows Start menu and then click Settings and Control Panel Double click Add or Remove Programs Click the software you want to remove Click Remove a PF YN Follow any on screen instructions to complete the uninstallation ENWW Remove software for Windows 63 Select the correct printer driver Printer drivers provide access to the device features and allow the computer to communicate with the MFP by using a printer language HP PCL 5 driver Recommended for general office Windows monochrome and color printing Backward compatible with previous PCL versions or older LaserJet printers Best choice for third party custom solutions forms fonts SAP programs or mixed environments UNIX Linux mainframe HP PCL 6 driver Recommended for printing in all Windows environments Provides the overall best performance print quality and printer feature support for most users Developed to align with Windows Graphic Device Interface GDI for best performance in Windows environments May not
102. LaserJet CM4730 MFP The tool includes solutions for many print quality issues using standard images to provide a common diagnostic environment It is designed to provide intuitive step by step directions for printing troubleshooting pages that are used to isolate print quality problems and provide possible solutions To find the print quality troubleshooting tool go to the following quick URL http www hp com go printquality ljcm47 30mfp Image defect examples Horizontal lines or streaks Defect description Horizontal lines or streaks appear on the page Possible causes 266 Chapter 16 Problem solving ENWW The device needs to be cleaned Operating environment or media in use does not meet HP specifications Troubleshooting and suggestions 1 Make sure that the environmental specifications for the device are being met 2 Print the Print Quality Troubleshooting Pages and follow the diagnostic procedure listed on the first page to help isolate the defect to a particular component ENWW Correct print quality and copy quality problems 267 Misaligned color Defect description Color does not appear in the correct area on the page Possible causes The device needs to be calibrated Troubleshooting and suggestions Calibrate the MFP 268 Chapter 16 Problem solving ENWW Vertical lines Defect description Vertical lines appear on the page Possible causes The device needs to be cleaned
103. MFP without any gaps between the MFP and the accessory Turn the MFP power on The accessory might have been disconnected and reconnected while the MFP power was on Reinstall Output Device appears on the control panel display Reconnect the cable on the accessory The job might have stalled between the MFP and the accessory Processing appears on the control panel display Turn the MFP power off and then on 260 Chapter 16 Problem solving ENWW Understand lights on the formatter Three LEDs on the formatter indicate that the MFP is functioning correctly Heartbeat LED HP Jetdirect LEDs This LED exists only if HP Jetdirect is installed HP Jetdirect LEDs The embedded HP Jetdirect print server has two LEDs The yellow LED indicates network activity and the green LED indicates the link status A blinking yellow LED indicates network traffic If the green LED is off a link has failed For link failures check all of the network cable connections In addition you can try to manually configure the link settings on the embedded print server by using the MFP control panel menus 1 SW JO Iv qe 0 Je Scroll to and touch Administration Touch Initial Setup Touch Networking and I O Touch Embedded Jetdirect or EIO X Jetdirect Touch Link Speed Select the appropriate link speed Touch Save Heartbeat LED The heartbeat LED indicates that the formatter is functioning corre
104. MFP is sold Do not convert operating voltages This can damage the MFP and void the product warranty Table C 3 Power requirements HP LaserJet CM4730 MFP series Specification 110 volt models 230 volt models Power requirements 100 to 127 volts 1096 220 to 240 volts 10 50 60 Hz 2 Hz 50 60 Hz 2 Hz Rated current 9 0 Amps 4 5 Amps Table C 4 Power consumption HP LaserJet CM4730 MFP series average in watts Product model Copying Printing Ready Sleep 6 Off HP Color LaserJet CM4730 MFP 615 604 83 24 0 5 HP Color LaserJet CM4730f MFP 615 604 83 24 0 5 HP Color LaserJet CM4730fsk 615 604 83 24 0 5 MFP HP Color LaserJet CM4730fm 640 626 86 25 0 5 MFP zx Values subject to change See http www hp com support ljcm4730mfp for current information Power numbers are the highest values measured using all standard voltages HP Color LaserJet CM4730 MFP series printing and copying speeds are 31 ppm Letter size and 30 ppm A4 size Heat dissipation in Ready mode 288 BTU hour Default time from Ready mode to Sleep mode 45 minutes Recovery time from Sleep mode less than 20 seconds wo N o a A Electrical specifications 313 Acoustic specifications Table C 5 Sound power and pressure level HP LaserJet CM4730 MFP series Sound power level Declared per ISO 9296 Printing Lwag 6 7 Bels A 67 dB A Copying Lwag 6 8 Bels A 68 dB A Ready Lwag
105. Microsoft operating systems e Windows 2000 e Windows Server 2003 e Windows XP e Windows Vista ET NOTE Do not connect the parallel or USB cable until the software prompts you to do so If the parallel or USB cable was connected before the software installation see Install the software after the parallel or USB cable has been connected 1 Close all software programs that are open or running 2 Insert the MFP CD into the CD ROM drive If the welcome screen does not open use the following procedure e Onthe Start menu click Run e Type X setup where X is the letter of the CD ROM drive e Click OK 3 When prompted click Install and follow the instructions on the computer screen 4 Click Finish when the installation is complete You might need to restart the computer 5 Printa Test Page or a page from any software program to make sure that the software is correctly installed If installation fails reinstall the software If this fails check the installation notes and Readme files on the MFP CD or go to http www hp com support licm4730mfp for help or more information Install Windows printing system software for networks ENWW The software on the MFP CD supports Microsoft network installation For information about network installation on other operating systems go to http www hp com support ljcm47 30mfp The HP Jetdirect embedded print server includes a 10 100 Base TX network port If you need a
106. P is networked always consult with the system administrator before changing settings on this tab The Settings tab contains the following pages Configure Device Configure all MFP settings from this page This page contains the traditional menus found on the control panel display These menus include Information Paper Handling Configure Device and Diagnostics e mail Server Use this page to set up the SMTP server that will be used to send MFP e mail alerts set up on the Alerts page Alerts Network only Set up to receive e mail alerts for various MFP and supplies events These alerts can be sent to a list of up to 20 e mail mobile device or Web site destinations AutoSend Use the AutoSend screen to send product configuration and usage information periodically to your service provider This feature establishes a relationship with Hewlett Packard Company or another service provider to provide you with services that include support agreements and usage tracking Security Set a password that must be typed in order to gain access to the Settings Digital Sending and Networking tabs Turn on and off certain features of the EWS Edit Other Links Add or customize a link to another Web site This link is shown in the Other Links area on all embedded Web server pages These permanent links always appear in the Other Links area HP Instant Support Order Supplies and Product Support Device Information Name the MFP and assign an asse
107. PBX ring signals Change this setting only when directed by an HP technical support agent Ring Frequency Default default This setting should be left at the default value and only changed when directed by an HP Custom technical support agent Adjustment procedures associated with this setting are beyond the scope of this guide Ringer Volume Off Set the volume for the fax ring tone Low default High Blocked Fax Add Blocked Numbers Numbers Type the fax number to add Remove Blocked Numbers Select a fax number to remove Clear All Blocked Numbers No default Yes Use this feature to add or delete numbers from the blocked fax list The blocked fax list can contain up to 30 numbers When the device receives a call from one of the blocked fax numbers it deletes the incoming fax It also logs the blocked fax in the activity log along with job accounting information ENWW Initial Setup menu 41 E mail Setup Administration gt Initial Setup gt E mail Setup Use this menu to enable the e mail feature and to configure basic e mail settings E NOTE To configure advanced e mail settings use the embedded Web server For more information see Embedded Web server Table 2 13 E mail Setup menu Menu item Values Description Address Validation On default This option enables the device to check e mail syntax when you type an e mail address Valid e mail addresses require
108. Printer Utility oec tune ert A A a er cae ner rei ATA 191 Print a Cleaning page eee edet ee e ee teet diee etie e ui e der ita 191 Printa configuration Page s otro te tete re dite e to Ebr eee ng 191 View supplies Status 3 ete RE e ebd edd ee epit Met cele ia exe cle eevee 192 Order supplies online and use other support features ssessssssseseseeeee 192 Upload a file to the printer entie tret cune e eee ea aa n ree sa dae ee dae 192 Update the firmware ente hune neues 193 Activate the two sided printing duplexing mode s 193 Lock or unlock printer storage devices sssssssee eene 193 Save or print stored jobs nete ri edet rte te d RR adi d ERR FR a ETE RR ER RRA 193 Configure rays esce ente at rt ce m toi eret ee pee dte tpa teo ee ee Meee ice 194 Change network settings treten tte eta pn eee n Loca ke nde d ee E En ERdud 194 Open the embedded Web server ssssssssssssssssssseeeeeeee enne 194 Setup esmall alerts 2 eet tete it dee f fte t de aan d det ka dceeedven sd 195 Security feat res snodi eei ducet deb iet a gei pec ce gam dne ea dud dne e aene De swine eee bees 196 Secure the embedded Web server sese nnns 196 Foreign Interface Harness FIH sssssssss eene eee eene 196 Requirements iine le tee qi phas a E d int Aie ene M bete oa dd 196 Use the FIEl zu d to DO Re Ue 196 Enable the FIH p
109. S EXPRESSED OR IMPLIED AND HP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE Some countries regions states or provinces do not allow limitations on the duration of an implied warranty so the above limitation or exclusion might not apply to you This warranty gives you specific legal rights and you might also have other rights that vary from country region to country region state to state or province to province HP s limited warranty is valid in any country region or locality where HP has a support presence for this product and where HP has marketed this product The level of warranty service you receive may vary according to local standards HP will not alter form fit or function ofthe product to make it operate in a country region for which it was never intended to function for legal or regulatory reasons TO THE EXTENT ALLOWED BY LOCAL LAW THE REMEDIES IN THIS WARRANTY STATEMENT ARE YOUR SOLE AND EXCLUSIVE REMEDIES EXCEPT AS INDICATED ABOVE IN NO EVENT WILL HP OR ITS SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT SPECIAL INCIDENTAL CONSEQUENTIAL ENWW Hewlett Packard limited warranty statement 301 INCLUDING LOST PROFIT OR DATA OR OTHER DAMAGE WHETHER BASED IN CONTRACT TORT OR OTHERWISE Some countries regions states or provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exc
110. Sides Touch this button to indicate if the original document is one sided or two sided Content Orientation Touch this button to select either the portrait or landscape orientation for the original Original Size Touch this button to select the size of the document letter A4 legal or mixed letter legal Optimize Text Touch this button to change the scanning procedure based on the type of document that you are Picture scanning Job Build Touch this button to activate or deactivate the Job Build mode which enables you to scan several small scan jobs and send them as one file Image Adjustment Touch this button to change the darkness and sharpness settings or to clean up background clutter on the original EEE SSS ENWW Change e mail settings for the current job 173 Scan to a folder If the system administrator has made the feature available the device can scan a file and send it to a folder on the network Supported operating systems for folder destinations include Windows 2000 Windows XP and Windows Server 2003 ET NOTE You might be required to supply a user name and password in order to use this option or to send to certain folders See your system administrator for more information 1 Place the document face down on the scanner glass or face up in the ADF From the Home screen touch Network Folder In the Quick Access Folders list select the folder in which you want to save the document
111. The final calibration target must look like the following figure CAUTION If the calibration target does not look like the figure shown here the calibration process will fail and the quality of scans will be degraded The black areas must extend completely to the short edges of the page If they do not use a black marker to extend the black areas to the edge of the page Ensure that the paper is loaded properly Place the calibration target face up into the ADF and adjust the side guides After the calibration target has passed through the ADF once reposition it face down in the ADF and touch Start Place the calibration target face down on the scanner glass touch Start and scan the page After this pass the calibration is complete 220 Chapter 15 Maintenance ENWW 16 Problem solving ENWW Solving general problems Determining MFP problems Control panel message types Control panel messages Jams Media handling problems Understand accessory lights for the 3 bin mailbox and stapler stacker Understand lights on the formatter Correct print quality and copy quality problems Solve fax problems Solve e mail problems Solve problems with output accessories Solve network connectivity problems Solve common Macintosh problems 221 Solving general problems If the MFP is not responding properly complete the steps in the following checklist in order If the MFP does not pass a ste
112. Web browser on the computer type the IP address for the MFP The MFP status window appears 2 Inthe Other links area double click Order Supplies This provides a URL from which to purchase consumables Supplies information with part numbers and MFP information is provided 3 Select the part numbers that you want to order and follow the instructions on the screen 296 Appendix A Supplies and accessories ENWW Optional output devices 1 Output accessory bridge 2 Stapler stacker 3 3 bin mailbox Output accessory bridge The output accessory bridge is required if a 3 bin mailbox or a stapler stacker is installed on the MFP The output accessory bridge is a pathway between the MFP and the output device For more information about installing the output accessory bridge see the installation guide that comes with the product 3 bin mailbox The optional 3 bin mailbox has one bin that stacks up to 500 sheets and two bins that stack up to 100 sheets each for a total capacity of 700 sheets ENWW Optional output devices 297 The 3 bin mailbox has three operating modes e Mailbox mode The bins can be assigned to a user or to a group of users All print copy and fax jobs that an assigned user or group of users sends are delivered to the designated bin Each user can select the bin in the printer driver or at the control panel When the designated bin is full the MFP stops printing Printing continues only when you em
113. XP Open HP Easy Printer Care software Use one of the following methods to open HP Easy Printer Care software e Inthe Windows system tray taskbar in the lower right hand corner of the desktop select HP Easy Printer Care software e Double click the HP Easy Printer Care software desktop icon HP Easy Printer Care software sections The HP Easy Printer Care software contains the sections described in the following table Section Description Overview tab e Devices list Shows the printers that you can select Contains basic status e Device Status section Shows printer status information This section indicates printer alert information for the conditions such as an empty print cartridge It also shows device identification information printer control panel messages and print cartridge levels After you correct a problem with the printer click the 9 Refresh button to update the section e Supplies Status section Shows detailed supplies status such as the percentage of toner remaining in the print cartridges and the status of the media that is loaded in each tray e Supplies Details link Opens the supplies status page to view more detailed information about printer supplies ordering information and recycling information Support tab e Provides device information including alerts for items needing attention Provides help information e and links Provides links to troubleshooting information and tools Provides li
114. a 2 Ifthe message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 13 XX YY JAM INSIDE OUTPUT ACCESSORY BRIDGE There is a paper jam inside the output accessory bridge 1 Follow the onscreen instructions to find and remove the jammed media 2 Ifthe message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 20 INSUFFICIENT MEMORY To continue touch OK The MFP received more data than can fit in the available memory You might have tried to transfer too many macros soft fonts or complex graphics Touch OK to print the transferred data some data might be lost and then simplify the print job or install additional memory 21 PAGE TOO COMPLEX To continue touch OK The page formatting process was not fast enough for the MFP Touch OK to print the transferred data Some data might be lost If this message appears often simplify the print job 228 Chapter 16 Problem solving ENWW Table 16 1 Control panel messages continued Control panel message Description Recommended action 22 EIO X BUFFER OVERFLOW To continue touch OK Too much data was sent to the EIO card in the specified slot x An incorrect communications protocol might be in use Touch OK to print the transferred data Some data might be lost Check the host configuration If this message persists contact an HP a
115. abled NOTE If you lose the PIN number and the portal needs to be disabled try using the default PIN that is listed to disable it For assistance use the HP Instant Support service which is available through the embedded Web server or at http instantsupport hp com See Embedded Web server Secure Disk Erase ENWW To protect deleted data from unauthorized access on the MFP hard drive use the Secure Disk Erase feature This feature can securely erase print and copy jobs from the hard drive Secure Disk Erase offers the following levels of disk security Non Secure Fast Erase This is a simple file table erase function Access to the file is removed but actual data is retained on the disk until it is overwritten by subsequent data storage operations This is the fastest mode Non Secure Fast Erase is the default erase mode Secure Fast Erase Access to the file is removed and the data is overwritten with a fixed identical character pattern This is slower than Non Secure Fast Erase but all data is overwritten Secure Fast Erase meets the U S Department of Defense 5220 22 M requirements for the clearing of disk media Secure Sanitizing Erase This level is similar to the Secure Fast Erase mode In addition data is repetitively overwritten by using an algorithm that prevents any residual data persistence This mode will impact performance Secure Sanitizing Erase meets the U S Department of Defense 5220 22 M requirements
116. age Then touch the up or down arrow buttons to scroll to other pages For details about how to use an option touch the option and then touch the help 9 button in the upper right corner of the screen The following table provides an overview of the copy options ET NOTE Depending on how the system administrator has configured the device some of these options might not appear The options in the table are listed in the order in which they can appear Option name Description Sides Use this feature to indicate whether the original document is printed on one or both sides and whether the copies should be printed on one or both sides Reduce Enlarge Use this feature to reduce or enlarge the copied image on the page Color Black Use this feature to choose black printing or color printing Staple Collate or Collate If the optional HP Stapler Stacker Separator is attached the Staple Collate option is available Use this feature to set up options for stapling and assembling the pages in sets of copies If the optional HP Stapler Stacker Separator is not attached the Collate option is available Use this feature to assemble each set of copied pages in the same order as the original document Paper Selection Use this feature to select the tray that holds the size and type of paper that you want to use Image Adjustment Use this feature to improve the overall quality of the copy For example you can adjust the darkness a
117. age that is not transparent 4 Next to Pages select whether to print the watermark on all pages or on the first page only 5 Next to Text select one of the standard messages or select Custom and type a new message in the box 6 Select options for the remaining settings Print multiple pages on one sheet of paper in Macintosh You can print more than one page on a single sheet of paper This feature provides a cost effective way to print draft pages 1 2 1i 2iilala gt S NM e 6 On the File menu in the software program click Print Select the driver and then click Properties or Preferences Click the Layout pop up menu Next to Pages per Sheet select the number of pages that you want to print on each sheet 1 2 4 6 9 or 16 Next to Layout Direction select the order and placement of the pages on the sheet Next to Borders select the type of border to print around each page on the sheet Print on both sides of the page duplex printing Automatic duplex printing Specify two sided printing options in your software program or in the printer driver If you cannot see this option use the following information to make the duplex printing options available ENWW Macintosh printer driver features 127 To use two sided printing Verify that the printer driver is configured to show the two sided printing options automatic and manual After the
118. aintain print quality clean the MFP thoroughly every time you replace the print cartridge and whenever print quality problems occur A WARNING Avoid touching the fusing area when cleaning the MFP It can be hot CAUTION To avoid permanent damage to the print cartridge do not use ammonia based cleaners on or around the MFP except as directed Clean the outside of the MFP e Clean the outside of the MFP if it is visibly marked e Use a soft lint free cloth dampened with water or water and a mild detergent Clean the touchscreen Clean the touchscreen whenever it is necessary to remove fingerprints or dust Wipe the touchscreen gently with a clean water dampened lint free cloth A CAUTION Use water only Solvents or cleaners can damage the touchscreen Do not pour or spray water directly onto the touchscreen Clean the scanner glass e Clean the scanner glass only if dirt is visible or if you are experiencing a decrease in copy quality such as streaking e Clean the scanner glass by wiping it gently with a clean slightly damp lint free cloth Use an ammonia based surface cleaner only when a water dampened cloth does not clean the scanner glass CAUTION Do not pour or spray liquids directly onto the scanner glass Do not press hard on the glass surface You could break the glass 212 Chapter 15 Maintenance ENWW Cleaning the ADF delivery system Clean the ADF only if it is visibly marked or dirt
119. an to 174 Networking tab embedded Web server 186 networks AppleTalk settings 34 configuring 81 configuring gateway addresses 166 connectivity features 7 default gateway 82 diagnostics 34 disabling DLC LLC 84 disabling protocols 83 DLC LLC settings 34 HP Jetdirect print server error messages 232 installing EIO cards 340 IP address 81 IPX SPX settings 34 link speed settings 37 print servers included 2 protocol configuration page printing 38 security 34 SMTP servers 166 subnet mask 82 TCP IP parameters 81 TCP IP settings 31 testing SMTP settings 167 troubleshooting printing 290 validating gateway addresses 288 noise specifications 314 Novell login required 235 NVRAM errors 231 O on off switch locating 9 online customer support 304 348 Index online help control panel 16 operating environment specifications 208 315 ordering part numbers for 299 supplies and accessories 296 ordering supplies 304 other links embedded Web server 187 output bins capacities 7 full error messages 235 locating 9 reattach error message 236 selecting 101 output path open error message 235 output quality troubleshooting 263 P pages per minute 5 pages per sheet 118 127 paper custom sizes 91 custom size Macintosh settings 126 custom size Windows settings 116 document size selecting 118 first page 116 126 load 93 pages per sheet 118 127 supported sizes 89 paper jams 3 bin mailbox 250 ADF 254 output accessory brid
120. ance kits and staples Usage Page Print Shows information about the number of pages that have been printed on each paper type and size File Directory Print A directory page that contains information for any mass storage devices such as flash drives memory cards or hard disks that are installed in this device Color Usage Job Log Print A directory page that contains job by job color usage information Page content includes the user name application name and number of black only pages and color pages Fax Reports Fax Activity Log Print Contains a list of the faxes that have been sent from or received by this device Fax Call Report Fax Call Report Print A detailed report of the last fax operation either sent or received Thumbnail on Report Yes Choose whether or notto include a thumbnail of the first page of the fax on the report No default When to Print Report Never auto print Print after any fax job Print after fax send jobs Print after any fax error default Print after send errors only Print after receive errors only Billing Codes Report Print A list of billing codes that have been used for outgoing faxes This report shows how many sent faxes were billed to each code Blocked Fax List Print A list of phone numbers that are blocked from sending faxes to this device Speed Dial List Print Shows the speed dials that have been set up for this device 18 Chapter 2 Control panel ENWW
121. and suggestions 1 Make sure that the environmental specifications for the device are being met 2 Make sure that type and quality of the media you are using meet HP specifications 3 Make sure that the media type and size for the tray are set correctly in the control panel for the media that you are using 4 Make sure that the media is loaded correctly and that the size guides are touching the edges of the stack of media 5 Make sure that the media you are using does not have any wrinkles or dents from handling and that the media is not contaminated with visible fingerprints or other foreign substances 274 Chapter 16 Problem solving ENWW Smeared toner Defect description Toner smears on the page Possible causes Media in use does not meet HP specifications Troubleshooting and suggestions Make sure that type and quality of the media you are using meet HP specifications ENWW Correct print quality and copy quality problems 275 White areas on page Defect description White areas dropouts appear on the page Possible causes Operating environment or media in use does not meet HP specifications Troubleshooting and suggestions 1 Make sure that the environmental specifications for the device are being met 2 Make sure that type and quality of the media you are using meet HP specifications 3 Make sure that the media you are using does not have any wrinkles or dents from handling and that the me
122. antees neutral colors that do not have a color cast e 4 Color generates neutral colors grays and black by combining all four toner colors This method produces smoother gradients and transitions to non neutral colors and it produces the darkest black ET NOTE Some software programs convert text or graphics to raster images In these cases the Photographs settings also control text and graphics RGB Color Five values are available for the RGB Color setting e Select Default SRGB for most printing needs This setting instructs the printer to interpret RGB color as sRGB which is the accepted standard of Microsoft and the World Wide Web Organization www e Select Image optimization SRGB to enhance documents in which the content is mainly bitmap images such as GIF or JPEG files This setting instructs the printer to use the best color matching for rendering SRGB bitmap images This setting has no effect on text or vector based graphics Using glossy media in combination with this setting provides the maximum enhancement e Select AdobeRGB for documents that use the AdobeRGB color space rather than sRGB For example some digital cameras capture images in AdobeRGB and documents that are produced with Adobe PhotoShop use the AdobeRGB color space When printing from a professional software program that uses AdobeRGB it is important that you turn off the color management in the software program and allow the printer software to
123. ar jams in the stapler stacker 1 Push the release lever on the top of the stapler stacker 2 Slide the stapler stacker out 3 4 Ifthe jam does not clear see Clear jams in the output accessory bridge To clear staple jams see Clear staple jams 248 Chapter 16 Problem solving ENWW Clear staple jams Occasionally staples become jammed in the stapler stacker If jobs are not being stapled correctly or are not being stapled at all use this procedure to clear staple jams 1 Turn off the MFP 2 Press and hold the release button on the top of the stapler stacker Pull the stapler stacker away from the MFP ENWW Jams 249 6 Remove the staples that protrude from the staple cartridge T 8 Reinsert the staple cartridge into the staple cartridge holder and push down on the green handle until it snaps into place Clear jams in the 3 bin mailbox 1 Push the release button on the top of the 3 bin mailbox 250 Chapter 16 Problem solving ENWW Slide the 3 bin mailbox out from the MFP 2 Open the cover on the top of the 3 bin mailbox 3 Jams 251 ENWW 4 Remove any media inside the cover 5 252 Chapter 16 Problem solving ENWW Clear jams in the output accessory bridge If a 3 bin mailbox or a stapler stacker is installed on the MFP compl
124. ard size media into tray 2 3 or 4 section Then proceed to step 3 in this procedure 3 Slide the tray into the MFP The MFP control panel shows the tray type and size configuration To specify specific custom dimensions or if the type is not correct touch OK when the MFP prompts to change the size or type 4 Ifthe configuration is correct touch Exit ENWW Load paper and print media 97 Configure trays The MFP automatically prompts you to configure a tray for type and size in the following situations When you load paper into the tray When you specify a particular tray or media type for a print job through the printer driver or a software program and the tray is not configured to match the print job s settings The following message appears on the control panel Tray X type size To change size or type touch Modify To accept touch OK ET NOTE The prompt does not appear if you are printing from tray 1 and tray 1 is configured for Any Size and Any Type NOTE If you have used other HP LaserJet printer models you might be accustomed to configuring tray 1 to First mode or Cassette mode On HP Color LaserJet CM4730 MFP series setting tray 1 size and type to Any Size is equivalent to First mode Setting size or type for tray 1 to a setting other than Any Size is equivalent to Cassette mode Configure a tray when loading paper 1 2 3 4 5 6 Load paper in
125. at lead to external Web sites 184 Chapter 14 Manage the MFP ENWW Information tab The Information pages group consists of the following pages Device Status This page shows the MFP status and shows the life remaining of HP supplies with 096 representing that a supply is empty The page also shows the type and size of print media set for each tray To change the default settings click Change Settings Configuration page This page shows the information that is found on the MFP configuration page Supplies Status This page shows the life remaining of HP supplies with 096 representing that a supply is empty This page also provides supplies part numbers To order new supplies click Order Supplies in the Other Links area of the window To visit any Web site you must have Internet access Event log This page shows a list of all MFP events and errors Usage page This page details the total usage of the MFP Device information This page shows the MFP network name address and model information To change these entries click Device Information on the Settings tab Control panel View the current status of the MFP control panel Print Select a file on your network or on the Web and send it to the MFP to be printed The document must be a print ready document such as a PS PDF PCL or TXT file Settings tab ENWW Use this tab to configure the MFP from your computer The Settings tab can be password protected If this MF
126. ax list printing 183 booklet printing 122 booklet settings Windows 123 books copying 162 both sides copying 158 both sides printing on errormessages 232 233 browser requirements embedded Web server 184 HP Web Jetadmin 190 buffer overflow errors 229 buttons control panel locating 14 touchscreen 16 C cabinet stand models including 3 specifications physical 311 cable parallel part number 300 cable USB part number 300 calibrating scanner 50 220 Index 343 call report fax 183 Canadian DOC regulations 325 canceling copy jobs 164 printing 136 canceling a print request 136 capacity 3 bin mailbox 7 ADF 6 output bins 7 stapler stacker 7 cartridges management menu 29 recycling 320 status viewing with embedded Web server 185 cartridges print error messages 234 Macintosh status 132 ordering 304 part numbers 299 warranty 306 cartridges staple empty stop or continue settings 134 loading 134 part numbers 299 checking toner level HP Easy Printer Care software 208 chosen personality not available 233 cleaning about 212 214 ADF delivery system 213 ADF rollers 214 glass 212 mylar strip 217 outside of MFP 212 touchscreen 212 clock error message 226 setting 199 collating copies 161 color adjusting 148 CMYK ink set emulation 144 edge control 148 151 four color printing 143 halftone options 149 150 344 Index HP ImageREt 3600 138 managing options 147 150 matching 145 neu
127. aximum is 2048 Timeout Specify the length of time in seconds to wait for a response from the remote host The default is 1 and the maximum is 100 Count Specify the number of ping test packets to send for this test Select a value from 1 to 100 To configure the test to run continuously select 0 Print Results If the ping test was not set for continuous operation you can choose to print the test results Select Yes to print results If you select No default results are not printed Execute Specify whether to initiate the ping test Select Yes to initiate the test or No to not run the test 36 Chapter2 Control panel ENWW Table 2 11 Jetdirect menus continued Menu item Sub menu item Sub menu item Values and Description Ping Results Use this item to view the ping test status and results using the control panel display You can select the following items Packets Sent Shows the number of packets 0 65535 sent to the remote host since the most recent test was initiated or completed Packets Received Shows the number of packets 0 65535 received from the remote host since the most recent test was initiated or completed Percent Lost Shows the percent of ping test packets that were sent with no response from the remote host since the most recent test was initiated or completed RTT Min Shows the minimum detected roundtrip time RTT from 0 to 4096 milli
128. busy Redial On No Answer Never default Once Twice Use this feature to specify the number of times the device should attempt to dial if the recipient fax number does not answer E NOTE Twice is available in locations other than the United States and Canada 40 Chapter2 Control panel ENWW Table 2 12 Fax Setup menu continued Menu item Sub menu item Sub menu item Values Description Redial Interval Detect Dial Tone Therange is between Use this feature to specify the number of 1 and 5 minutes The minutes between dialing attempts if the factory default is 5 minutes Enabled Disabled default recipient number is busy or not answering Use this feature to specify whether the device should check for a dial tone before sending a fax Dialing Prefix Off default Use this feature to specify a prefix number that must be dialed when sending faxes from Custom the device Billing Codes Off default When billing codes are enabled a prompt appears that asks the user to enter the billing Custom code for an outgoing fax The range is between 1 and 16 digits The default is 1 digit Fax Receive Settings Rings To Answer The range varies by location The factory default is 2 rings Use this feature to specify the number of rings that must occur before the fax modem answers Ring Interval Default default Custom This setting is used to adjust for some
129. c trademarks are the property of Pantone Inc Pantone Inc 2000 Sample book color matching ENWW The process for matching MFP output to preprinted sample books and standard color references is complex In general you can obtain a reasonably good match to a sample book if the inks used to create the sample book are cyan magenta yellow and black These are usually referred to as process color sample books Some sample books are created from spot colors Spot colors are specially created colorants Many of these spot colors are outside of the range of the MFP Most spot color sample books have companion process sample books that provide CMYK approximations to the spot color Color matching 145 Most process sample books will state which process standards were used to print the sample book In most cases they will be SWOP EURO or DIC To get optimal color matching to the process sample book select the corresponding ink emulation from the MFP menu If you cannot identify the process standard use SWOP ink emulation Printing color samples To use the color samples select the color sample that is the closest match to the desired color Use the sample s color value in your software program to describe the object you wish to match Colors may vary depending on paper type and the software program used For more details on how to use the color samples go to http Awww hp com support licm4730mfp Use the following procedure to p
130. cal list by touching Local in the drop down list Highlight the appropriate names and then touch to add the name to your list of recipients You can remove a recipient from your list by scrolling to highlight the recipient and then touching the remove button 3 The names in the recipient list are placed in the text line of the keyboard screen If you want you can add a recipient that is not found in the address book by typing the e mail address on the keyboard After you are satisfied with your recipient list touch OK 4 Touch OK 5 Finish typing information in the CC and Subject fields on the Send E mail screen if necessary You can check the list of recipients by touching the down arrow in the To text line 6 Press Start Use the local address book ENWW Use the local address book to store frequently used e mail addresses The local address book can be shared between devices that use the same server to gain access to the HP Digital Sending software You can use the address book when you type e mail addresses in the From To CC or BCC fields You can also add or delete addresses in the address book To open the address book touch the address book button Use the address book 171 Add e mail addresses to the local address book 1 2 Touch Local Touch Optional Touch the Name field and in the keyboard that appears type a name for the new entry Touch OK The name is the alias for th
131. can install an additional I O card in the available EIO slot 1 Turn the MFP off 2 340 Appendix E Install memory and print server cards ENWW 3 Locate an open EIO slot Loosen and remove the two retaining screws holding the cover for the EIO slot and then remove the cover You will not need these screws and the cover again They can be discarded ENWW Install an HP Jetdirect or EIO print server card 341 6 Connect the network cable 7 8 Print a configuration page In addition to an MFP configuration page and a Supplies Status page an HP Jetdirect configuration page that contains network configuration and status information should also print If it does not print uninstall and reinstall the print server card to ensure that it is completely seated in the slot 9 Perform one of these steps e X Choose the correct port See the computer or operating system documentation for instructions e Reinstall the software choosing the network installation this time 342 Appendix E Install memory and print server cards ENWW Index Symbols Numerics 2 sided printing 119 127 3 bin mailbox capacity 7 configuring 102 light status 260 models including 4 modes 297 part number 299 reattach error message 236 selecting 101 specifications physical 311 500 sheet input tray models including 2 500 sheet trays insert or c
132. can view the current IP address of the device from the control panel Home screen by touching Network Address Use the following procedure to change the IP address manually 1 Scroll to and touch Administration 2 Scroll to and touch Initial Setup 3 Touch Networking and I O 4 Touch Embedded Jetdirect 5 Touch TCP IP Network configuration 81 o se E 9 10 11 12 13 14 15 Touch IPVA Settings Touch Config Method Touch Manual Touch Save Touch Manual Settings Touch IP Address Touch the IP Address text box Use the touchscreen keypad to type the IP address Touch OK Touch Save Set the subnet mask 1 Dr psc uh Do 401 ANC IM GRO A A A RF RP gt 8 15 Scroll to and touch Administration Scroll to and touch Initial Setup Touch Networking and I O Touch Embedded Jetdirect Touch TCP IP Touch IPV4 Settings Touch Config Method Touch Manual Touch Save Touch Manual Settings Touch Subnet Mask Touch the Subnet Mask text box Use the touchscreen keypad to type the subnet mask Touch OK Touch Save Set the default gateway 1 2 3 4 Scroll to and touch Administration Scroll to and touch Initial Setup Touch Networking and I O Touch Embedded Jetdirect 82 Chapter 6 Connectivity ENWW ofS N m 10 11 12 13 14 15 Touch TCP IP Touch IPV4 Settings Touch Config Method Touch Manual Touch Save Touch
133. cartridge might be installed Ensure that you are using a genuine HP print cartridge Cartridge error Table 16 5 Inconsistent colors after installing a print cartridge cause and solution Cause Solution Another print cartridge might be low Check the supplies gauge on the control panel or print a supplies status page Print cartridges might be improperly installed Verify that each print cartridge is installed properly A non HP cartridge might be installed Ensure that you are using a genuine HP print cartridge Color match error Table 16 6 Printed colors do not match screen colors cause and solution Cause Solution Extremely light screen colors are not being printed The software program might interpret extremely light colors as white If so avoid using extremely light colors Extremely dark screen colors are being printed in black The software program might interpret extremely dark colors as black If so avoid using extremely dark colors The colors on the computer screen differ from the MFP output On the printer driver s Color Control tab select Screen Match 264 Chapter 16 Problem solving ENWW Table 16 6 Printed colors do not match screen colors continued cause and solution Cause Solution ET NOTE Several factors can influence your ability to Z match printed colors to those on your screen These factors include print media overhead lighting software programs ope
134. cating For example type telnet 123 123 123 123 25 where 123 123 123 123 represents the SMTP gateway address 3 Press Enter If the SMTP gateway address is not valid the response contains the message Could not open connection to the host on port 25 Connect Failed 4 Ifthe SMTP gateway address is not valid contact the network administrator Validate the LDAP gateway address ET NOTE This procedure is for Windows operating systems 1 Open Windows Explorer In the address bar type LDAP immediately followed by the LDAP gateway address For example type LDAP 12 12 12 12 where 12 12 12 12 represents the LDAP gateway address 2 Press Enter If the LDAP gateway address is valid the Find People dialog box opens 3 Ifthe LDAP gateway address is not valid contact the network administrator 288 Chapter 16 Problem solving ENWW Solve problems with output accessories When the 3 bin mailbox or the stapler stacker is installed correctly with the output accessory bridge the LED at the top of the accessory is green If the LED is off is blinking or is amber a problem exists See Understand accessory lights for the 3 bin mailbox and stapler stacker For information about clearing jams see Jams 1 LED for the stapler stacker 2 LED for the 3 bin mailbox ENWW Solve problems with output accessories 289 Solve network connectivity problems If the MFP is having problems communicating with the network
135. cceceeeceeee cece cceeaeeeaaecaeeaeeeeeeeeeeeeeeeeteeeeeteeenees 108 Create a proof and hold job ssssssseeeeenn 108 Print the remaining copies of a proof and hold job sssssess 108 Delete a proof and hold job ssssssssssseeenen eene 108 Use the personal Job feature exe dde Pear e eh ede gout vae teu d nM ep quu Rb ita de xxn 109 Create a personal JOD rnnt des EA 109 Pinta personal JOD e ch Eee ceo acts e Hp tes chr be ete Map ed eM ds 109 Delete a persorial JOD ide eee t ea e e ede 109 Use the QuickCopy feature sse mener nennen 110 Create a QuickCopy Job cernerent EEEE 110 Print additional copies of a QuickCopy job se 110 ENWW V Delete a QuickCopy JOD 2 22 intei ordei Aaa A de dtes 110 Use the stored Job feature ort rre eren FREE ao Romper uua a usus 111 Create a stored copy JOD side i teet taa te eee eu o ERE dee nha ERRARE ce 111 Create a stored print job ssssssssssssseeen emen 111 Print a stored JOD nde dere ie ree E e dre ba i reb a n decus 111 Delete a stored job sssssssssssseeee eme nennen nen 112 9 Print tasks Media type and tray loading eiii reine nate Ea saa net EY RR XXE ER ARE RR o SEX ERR e Ra REX VR Ra que EREG 114 Windows printer driver features sesssssssssssssssseseessesseeeeenen nene nennen nennen nennen rennen nnns 116 Create and use pri
136. control panel to determine the media size for which the tray is configured The guides in the tray are not against the paper Verify that the rear and width media guides are touching the paper Media does not feed from tray 2 3 or 4 Media does not feed from tray 2 3 or 4 Cause Solution The correct size media is not loaded Load the correct size media The input tray is empty Load media in the input tray The correct media type for the input tray is not selected in the MFP control panel From the MFP control panel select the correct media type for the input tray Media from a previous jam has not been completely removed Open the MFP and remove any media in the paper path Closely inspect the fuser area for jams None of the optional trays appear as input tray options The optional trays only display as available if they are installed Verify that any optional trays are correctly installed Verify that the printer driver has been configured to recognize the optional trays An optional tray is incorrectly installed Print a configuration page to confirm that the optional tray is installed If not verify that the tray is correctly attached to the MFP Media handling problems 257 Media does not feed from tray 2 3 or 4 Cause Solution The media size is not configured correctly for the input tray Print a configuration page or use the control panel to determine t
137. cription Recommended action the HP support flyer or go to http www hp com support ljcm47S30mfp 50 X FUSER ERROR A fuser error has occurred Make sure you have the correct fuser Re seat the fuser Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support licm4730mfp 51 XY ERROR To continue turn off then on A temporary printing error has occurred Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http Awww hp com support licm4730mfp 52 XY ERROR To continue turn off then on A temporary printing error has occurred Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support ljcm47S30mfp 53 10 0X Unsupported DIMM An unsupported DIMM is installed 1 Turn the MFP off and then replace the DIMM that caused the error 2 If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support ljcm4730mfp 55 XX YY DC CONTROLLER ERROR To continue turn off then on The print engine is not communicating with the formatter T
138. ct color copying eee 139 Paper selection mE P UXREUPIEELEE 140 erelfegdee E 141 clieme EREEEERR 142 Print in four colors CMYK 2 ceeceeeecaeee cece erect eee eee eee aaaaaaaeeaeeceeeeeeeeeeeeceesececeaaeaaesaeeeeeeeeeeeeeneaea 143 CMYK ink set emulation PostScript only sssesene enne nennen 144 Color MACGNING em 145 PANTONE color matching ecrire a A 145 Sample book color matching sssssssssssseenee E A enne nnns 145 Printing color samples ade eet petit T kun dpa Dux ee Rt aecenas 146 Manage printer color options on Windows computers ssssssssssssssseeeee nne 147 Prints grayscale esos ent aet rte tied SR R EU Ee RR Up aea tdt een Rate creat nM ds 147 Setting the color options in Windows sssee meer 147 RGB Color Color Themes ssssssssssseeee eene nennen emnes 147 Automatic or manual color adjustment sss 148 Manual color options sss eene nnn nnn 148 Manage printer color options on Macintosh computers sssssssssseeeemm 150 Print Color as Gray sede e sp dr dne reap EEA 150 Setting the color options in Macintosh ssssssse nennen 150 Advanced color options for text graphics and photographs sss 150 Halftone optlons eec tere Rn ed e Ra namen hase d a eU Re
139. ctly While the MFP is initializing after you turn it on the LED blinks rapidly and then turns off When the MFP has finished the initialization sequence the heartbeat LED pulses on and off ENWW Understand lights on the formatter 261 If the heartbeat LED is off the formatter might have a problem Contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support licm4730mfp 262 Chapter 16 Problem solving ENWW Correct print quality and copy quality problems This section helps you define print quality problems and what to do to correct them Often print quality problems can be handled easily by making sure that the MFP is properly maintained using print media that meets HP specifications or running a cleaning page Print quality problems associated with media Some print quality problems arise from use of inappropriate media Use paper that meets HP paper specifications The surface of the media is too smooth Use media that meets HP paper specifications The printer driver setting might be incorrect Be sure that you have selected the correct driver setting for the paper that you are using The print mode might be set incorrectly or the paper might not meet recommended specifications The transparencies you are using are not designed for proper toner adhesion Use only transparencies designed for HP Color LaserJet printers The moisture content of the paper is uneven too h
140. d HP Color LaserJet CM4730fm MFP models come with a fax accessory already installed For the HP Color LaserJet CM4730 MFP base model you can order this accessory as an option See Part numbers for information about ordering the analog fax accessory The Analog Fax Accessory 300 Fax Guide and the Analog Fax Accessory 300 Send Fax Driver Guide are located on the MFP software CD or at http www hp com go mfpfaxaccessory300 Connect the fax accessory to a phone line When connecting the fax accessory to a phone line ensure that the phone line being used for the fax accessory is a dedicated line that is not used by any other devices Also this line should be an analog line because the fax will not function correctly if it is connected to some digital PBX systems If you are not sure whether you have an analog or digital phone line contact your telecom provider ET NOTE HP recommends using the phone cord that comes with the fax accessory to ensure that the accessory functions correctly Follow these instructions to connect the fax accessory to a phone jack 1 Locate the phone cord that is included with the fax accessory kit Connect one end of the phone cord into the fax accessory phone jack that is on the formatter Push the connector until it clicks CAUTION Be sure to connect the phone line to the fax accessory port which is located in the center of the formatter Do not connect the phone lin
141. d a memory DIMM go to Enabling memory Install a flash memory card 334 Appendix E Install memory and print server cards ENWW AN CAUTION Do not insert a flash memory card that is designed for use with a digital camera into the MFP The MFP does not support photo printing directly from a flash memory card If you install a camera type flash memory card the control panel displays a message asking if you want to reformat the flash memory card If you choose to reformat the card all data on the card will be lost 1 Turn the MFP off 2 ENWW Install memory and fonts 335 3 Locate the gray formatter pressure release tabs on the formatter board in the rear of the MFP 4 Gently squeeze the tabs and pull them out of the formatter 5 Gently pull on the black tabs to pull the formatter board from the MFP Place the formatter board on a clean flat grounded surface CEN jm ex jg 336 Appendix E Install memory and print server cards ENWW Align the groove on the side of the flash memory card with the notches in the connector and push it in the slot until it is fully seated A CAUTION Do not insert the flash memory card at an angle ET NOTE The first flash memory slot marked Firmware Slot is reserved for firmware only z Slots 2 and 3 should be used for all other solutions Align the formatter board in the track
142. d and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense 318 Appendix D Regulatory information ENWW Declaration of Conformity Declaration of Conformity according to ISO IEC 17050 1 and EN 17050 1 Manufacturer s Name Hewlett Packard Company DoC BOISB 0503 00 rel 2 0 Manufacturer s Address 11311 Chinden Boulevard Boise Idaho 83714 1021 USA declares that the product Product Name HP Color LaserJet CM4730 MFP series Accessories Q7521A Q7522A Q7523A BOISB 0308 009 Regulatory Model Number BOISB 0503 00 Product Options ALL Toner Cartridges Q6460A Q6461A Q6462A Q6463A Q7504A Q7503A Q7502A conforms to the following Product Specifications Safety IEC 60950 1 2001 EN60950 1 2001 A11 IEC 60825 1 1993 A1 A2 EN 60825 1 1994 A1 A2 Class 1 Laser LED Product GB4943 2001 EMC CISPR 22 1993 A1 A2 EN 55022 1994 A1 A2 Class A EN 61000 3 2 2000 EN 61000 3 3 1995 A1 2001 EN 55024 1998 A1 2001 A2 2003 FCC Title 47 CFR Part 15 Class A ICES 003 Issue 4 GB9254 1998 GB17625 1 2003 Supplementary Information The product herewith complies with the requirements of the EMC Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC and carries the CE Marking accordingly
143. d for plain paper on the MFP control panel Selecting media by Type and Size results in significantly better print quality for heavy paper glossy paper and transparencies Using the wrong setting might result in unsatisfactory print quality Always print by Type for special print media such as labels or transparencies Print by Size for envelopes if possible e Toprint by Type or Size select the Type or Size from the Page Setup dialog box the Print dialog box or the Print Properties dialog box depending on the software program e Ifyou often print on a certain type or size of media configure a tray for that type or size Then when you select that type or size as you print a job the MFP pulls media from the tray that is configured for that type or size 100 Chapter 7 Paper and print media ENWW Select the output bin Standard output bins The MFP has an ADF output bin and the standard output bin for printed pages 1 Standard output bin 2 ADF output bin for copy originals When you scan or copy documents by using the ADF the originals are automatically delivered to the ADF output bin Copies made from the scanner glass are delivered to the standard output bin or the output bin s on the stapler stacker or the 3 bin mailbox When you send print jobs to the MFP from a computer the output is to the standard output bin or the output bin s on the stapler stacker or the 3 bin mailbox 3 bin mailbox output bin
144. der See the HP support flyer or go to http Awww hp com support licm4730mfp 60 X ERROR To continue turn off then on 62 NO SYSTEM To continue turn off then on The tray specified by X is not lifting correctly A problem exists with the MFP firmware Follow the instructions in the onscreen dialog box Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http Awww hp com support licm4730mfp 64 ERROR To continue turn off then on A scan buffer error occurred Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support licm4730mfp 66 12 34 OUTPUT ACCESSORY FAILURE An output accessory is not functioning properly 1 Turn off the MFP 2 Verify that all external paper handling devices are securely connected 3 Ifthe device uses cables disconnect and reconnect them 4 Turn on the MFP If error reappears write down the message and contact HP support 66 XY ZZ OUTPUT DEVICE FAILURE 68 X PERMANENT STORAGE FULL To continue touch OK An error occurred in an external paper handling accessory The MFP NVRAM is full Some settings saved in the NVRAM might have been reset to the factory defaults Printing can continue but some unexpected functions
145. dia is not contaminated with visible fingerprints or other foreign substances 4 Make sure that the media type and size for the tray are set correctly in the control panel for the media that you are using 276 Chapter 16 Problem solving ENWW Media damage ENWW Defect description The media has wrinkles curls creases or tears Possible causes Operating environment or media in use does not meet HP specifications Trays are not configured properly or settings are not correct for media in use There are undetected jams Troubleshooting and suggestions d 2 3 4 Make sure that the environmental specifications for the device are being met Make sure that type and quality of the media you are using meet HP specifications Make sure that the media is loaded correctly Make sure that the media type and size for the tray are set correctly in the control panel for the media that you are using Make sure that the media you are using does not have any wrinkles or dents from handling and that the media is not contaminated with visible fingerprints or other foreign substances Make sure that the fuser and transfer belt are seated correctly Inspect the jam areas and remove any undetected jammed or torn media Correct print quality and copy quality problems 277 Specs or stray toner Defect description Toner specs or stray toner appear on the page Possible causes Operating environment or media in use does
146. drivers 67 priority 66 shortcuts Windows 116 Settings tab embedded Web server 185 shortcuts 116 shortcuts Macintosh 126 size media unexpected error message 229 skewed page 279 skewed page problem solving 279 skewed pages 282 Sleep button 14 Sleep mode settings 27 29 sleep settings delay 106 power specifications 313 wake time 106 350 Index smeared toner 275 smeared toner problem solving 275 SMTP gateways error messages 237 SMTP servers configuring gateway address 166 connecting to 166 testing 167 validating gateway addresses 288 software downloading 304 embedded Web server 85 HP Easy Printer Care software 86 HP Web Jetadmin 85 installing 59 Macintosh 70 86 305 settings 66 uninstalling Macintosh 71 Windows 86 space requirements 311 special media guidelines 92 special paper guidelines 92 specifications acoustic 314 electrical 313 features 5 operating environment 208 315 physical 311 skew 282 specs 278 specs problem solving 278 speed dial list printing 183 speed specifications 5 stacker mode 3 bin mailbox 298 standard output bin Capacity 7 locating 9 reattach error message 236 selecting 101 staple cartridges empty stop or continue settings 134 loading 134 part numbers 299 staple jams 249 stapler stacker capacity 7 empty stop or continue settings 134 light status 260 loading staples 134 models including 3 part number 299 reattach error message 236 selecting 101 specificati
147. e Description Recommended action E mail Gateway rejected the job because of the addressing information Job failed One or more of the e mail addresses is incorrect Send the job again with the correct addresses Error executing Digital Send job Job failed A digital send job has failed and cannot be delivered Try to send the job again Folder list is full To add a folder you must first delete a folder The MFP limits the number of folders that can be established Delete an unused folder to add a new folder HP Digital Sending Delivery Error A digital send job has failed and cannot be delivered Try to send the job again Incorrect color Cartridge A print cartridge is in the incorrect color slot Verify that each color cartridge is in the correct slot Incorrect Supplies A print cartridge is in the incorrect color slot Verify that each color cartridge is in the correct slot Insert or close tray XX The specified tray is missing or open Insert or close the specified tray to continue Install color cartridge The print cartridge has been removed or has been installed incorrectly Replace or reinstall the print cartridge correctly to continue printing Install supplies At least one supply item is missing incorrectly placed out or low Insert the supply item or make sure the installed supply item is fully seated Insufficient memor
148. e representative if these steps do not work The MFP is turned on but the internal fans are not running Make sure that the line voltage is correct for the MFP power configuration See the label that is inside the top cover on the MFP for voltage requirements If you are using a power strip and its voltage is not within specification plug the MFP directly into the power receptacle The MFP voltage is not correct Make sure that the line voltage is in the correct range See the label that is inside the top cover on the MFP for voltage requirements Messages appear on the control panel display See Electrical specifications Print media is jammed in the MFP Check for jams For more information see Jams The control panel display shows the wrong language or unfamiliar characters Reconfigure the control panel display language 1 Turn the MFP off and then on 2 When XXX MB appears on the control panel display press and hold 6 until all three LEDs flash once and then stay on This might take up to 20 seconds 3 Release 6 and then press 6 again 4 Wait while the MFP completes its initialization sequence When it is finished the Select a Language menu appears on the control panel display Scroll to and touch the correct language An error occurs during a Digital Send job Job failed The MFP experienced an error during the digital sending job The administrator should check on the status
149. e e mail address If you do not type an alias name the alias will be the e mail address itself Touch the Address field and in the keyboard that appears type the e mail address for the new entry Touch OK Delete e mail addresses from the local address book You can delete e mail addresses that you no longer use ET NOTE To change an e mail address you must first delete the address and then add the corrected address as a new address in the local address book Touch Local Touch the e mail address that you want to delete Touch The following confirmation message appears Do you want to delete the selected address es Touch Yes to delete the e mail address es or touch No to return to the Address Book screen 172 Chapter 12 Scan and send to e mail ENWW Change e mail settings for the current job Use the More Options button to change the following e mail settings for the current print job Button Description Document File Type Touch this button to change the type of file the device creates after scanning the document Output Quality Touch this button to increase or decrease the print quality of the file being scanned A higher quality setting produces a larger file size Resolution Touch this button to change the scan resolution A higher resolution setting produces a larger file size Color Black Touch this button to determine whether you will scan the document in color or in black and white Original
150. e embedded Web server MFP software HP Easy Printer Care software or through the HP Web Jetadmin software On the MFP control panel 1 From the Home screen touch Administration 2 Touch Information 3 Touch Configuration status Pages 4 Touch Supplies Status Page 5 Touch Print ET NOTE Ifyou are using non HP supplies the supplies status page might not show the remaining life for those supplies In the embedded Web server In your browser type the IP address or host name for the printer home page This takes you to the printer status page M On the left side of the screen click Supplies Status This takes you to the supplies status page which provides print cartridge information Through HP Easy Printer Care software In the Overview tab in the Supplies Status section click Supplies Details to open the supplies status page Through HP Web Jetadmin In HP Web Jetadmin select the printer device The device status page shows print cartridge information 208 Chapter 14 Manage the MFP ENWW 15 ENWW Maintenance e Replace supplies e Clean the MFP e ADE maintenance kit e Calibrate the scanner Replace supplies When you use genuine HP supplies the MFP automatically notifies you when supplies are nearly depleted The notification to order supplies allows ample time to order new supplies before they need to be replaced For more information about ordering supplies see Supplies a
151. e kt v E THEE RET ER et a ees 210 Supply replacement guidelines ssssssssssssssssesseeeneene eren 210 Approximate replacement intervals for supplies ssssse 210 Change print cartridges ssssssessssssseee enne nnnnnmnrrnnen nnne 211 e murum 212 Clean the outside of the MFP sssssssssssssssssssessseeeeeene enne enne nennen 212 Clean the touchscreen sssssssssssssssssesssssese ener eerte nn senes nennt nenne nere 212 Clean the scanner glass itte decre e ter ee reb cde te Ea ED esp vectes p dca 212 Cleaning the ADF delivery system sssssssseeeeeeeeenneneeeennn nennen 213 Clean the ADF delivery system eeesesesessseeese eene nnn nhn nnne 213 Clean the ADF rollers 0 0 ccccccccececceeceeeeeeeeeceeeeaeaaecaeeeeeeeeeeeeeeeeeeteeseesneneeaaanes 214 Clean the mylar Strip ic etitm eremi ern ka EO eR Ro RA a EN SMR RA Yee ARR YR ENRE ARR Run 217 ADF maintenance Kit c cccceccecceeeeeee eee eeeeeee eee eaaeeaeceeeeeeeeeeeeesee cee caaaaaaaeaaeeeeeeeeeeeeeeeseetessensaaeeees 219 Calibrate the Scanner dresirani nns a seria ented en tr ge ed a ns eed eee 220 16 Problem solving Solving General Problems sssrinin RA NAERA uk Fe ive dia d e o Eines 222 Troubleshooting checklist rtr orte terree tex gene nud core te qued eus 222 Determining MFP problems 2 1 diritti headed enr h aeu E HRS RR Ie Red RETE eo
152. e original documents face down on the glass Align the corner of the original with the upper left corner of the glass To make copies by using the default copy options use the numeric keypad on the control panel to select the number of copies and press Start To use customized settings touch Copy Specify the settings and then press Start For more information about using customized settings see Adjust the copy settings Copy from the document feeder Use the document feeder to make as many as 999 copies of a document that has up to 50 pages depending on the thickness of the pages Place the document into the document feeder with the pages facing up To make copies by using the default copy options use the numeric keypad on the control panel to select the number of copies and press Start To use customized settings touch Copy Specify the settings and then press Start For more information about using customized settings see Adjust the copy settings Before starting another copy job retrieve the original document from the document feeder output bin that is under the document feeder input tray and retrieve the copies from the appropriate output bin 156 Chapter 11 Copy ENWW Adjust the copy settings The device offers several features so you can optimize copied output These features are all available on the Copy screen The Copy screen consists of several pages From the first page touch More Options to go to the next p
153. e procedure for each day 106 Chapter 8 Use product features ENWW Job storage features The following job storage features are available for print jobs e Proof and hold jobs This feature provides a quick and easy way to print and proof one copy of a job and then print the additional copies e Personal jobs When you send a private job to the device the job does not print until you provide the required personal identification number PIN at the control panel e QuickCopy jobs You can print the requested number of copies of a job and then store a copy of the job on the device hard disk Storing the job allows you to print additional copies of the job later e Stored jobs You can store a job such as a personnel form time sheet or calendar on the device and allow other users to print the job at any time Stored jobs also can be protected by a PIN Follow the instructions in this section to gain access to the job storage features at the computer See the specific section for the type of job that you want to create CAUTION If you turn off the device all QuickCopy proof and hold and personal jobs are deleted Gain access to the job storage features For Windows 1 On the File menu click Print 2 Click Properties and then click the Job Storage tab 3 Select the job storage mode that you want For Macintosh In newer drivers Select Job Storage in the pull down menu in the Print dialog box In older drivers select Printe
154. e test page to all output bins or only Stacker Bin to a specific bin Standard Output Bin Duplex Off default Select whether the duplexer should be included in the test On Copies Range 2 30 Select how many pages should be sent from Default 2 the specified source as part of the test ENWW Troubleshooting menu 51 Table 2 17 Troubleshooting menu continued Menu item Sub menu item Sub menu item Values Description Finishing Paper Path Staples Test Finishing Options Choose from a list of available options Test the paper handling features on the finisher Select the option that you want to test Media Size Letter Select the paper size for the test Legal A4 Executive JIS 8 5 x 13 Media Type Select from alist of Select the paper type for the test types Copies Range 2 30 Select the number of copies to include in the Default 2 test Duplex Off Select whether to use the duplexer in the test On Test Page Print Print a test page to use for the test Stack Media Size Letter Select the options that you want to use to test the stacker Legal A4 Executive JIS 8 5 x 13 Media Type Select from alist of Select the type of media to use for the types Finishing Paper Path Test Copies 1 Select the number of copies to include in the Finishing Paper Path Test 10 50 100 500 Duplex Off Select whether to use the duplexer in the Finishing Paper Path Test On Test Page Print Print a
155. e the rollers with a clean water dampened lint free cloth AN CAUTION Do not pour water directly onto the rollers Doing so might damage the device 216 Chapter 15 Maintenance ENWW 8 Locate the separation pad 9 Wipe the pad with a clean water dampened lint free cloth 10 Close the ADF cover Clean the mylar strip Clean the mylar strips on the underside of the scanner lid only if you are experiencing a decrease in copy quality such as vertical lines when copying using the ADF 1 Open the scanner lid ENWW Clean the MFP 217 2 Locate the mylar strip 1 394 NOTE Replacement mylar strips are stored in an envelope 2 that is underneath the white vinyl ADF backing Follow the instructions that are in the envelope 3 Clean the mylar strip with a clean damp lint free cloth 4 Close the scanner lid 218 Chapter 15 Maintenance ENWW ADF maintenance kit After feeding 90 000 pages through the ADF a Replace Document Feeder Kit message appears on the control panel display This message appears approximately one month before the kit needs to be replaced Order a new kit when this message appears See Part numbers for information about ordering a new ADF maintenance kit The ADF maintenance kit includes the following items One pick up roller assembly One separation pad One mylar sheet kit An instruction sheet Follow the instructions that come with the kit to install it A
156. e to the HP Jetdirect port which is nearer the bottom of the formatter 2 Connectthe other end of the phone cord into the phone jack on the wall Push the connector until it clicks or until it is securely seated Because different types of connectors are used in different countries regions the connector might not make an audible click 178 Chapter 13 Fax ENWW Configure and use the fax features Before you can use the fax features you must configure them in the control panel menus For complete information about configuring and using the fax accessory and for information about troubleshooting problems with the fax accessory see the HP LaserJet Analog Fax Accessory 300 User Guide This guide is provided with the fax accessory and it is also available on the MFP software CD Use the Send Fax driver to send a fax from a computer without going to the MFP control panel See the HP LaserJet MFP Analog Fax Accessory 300 Send Fax Driver Guide for more information The HP LaserJet Analog Fax Accessory 300 User Guide and HP LaserJet MFP Analog Fax Accessory 300 Send Fax Driver Guide are both available on the MFP software CD ENWW Analog fax 179 Digital fax Digital faxing is available when you install the optional HP Digital Sending Software For information about ordering this software go to http www hp com go digitalsending With digital faxing the MFP does not need to be connected directly to a phone line Instead the MFP can s
157. e using Mac OS X click Show Advanced Options 4 Manually adjust the individual settings for text graphics and photographs Advanced color options for text graphics and photographs Use manual color adjustment to adjust the Color or Color Map and Halftoning options for a print job Halftone options Halftone options affect the resolution and clarity of your color output You can select halftone settings independently for text graphics and photographs The two halftone options are Smooth and Detail e The Smooth option provides better results for large solid filled print areas It also enhances photographs by smoothing out fine color gradations Select this option when uniform and smooth area fills are the top priority e The Detail option is useful for text and graphics that require sharp distinctions among lines or colors or for images that contain a pattern or a high level of detail Select this option when sharp edges and details are the top priority 150 Chapter 10 Using color ENWW ET NOTE Some software programs convert text or graphics to raster images In these cases the Photographs settings also control text and graphics Neutral Grays The Neutral Grays setting determines the method that the printer uses to create gray colors in text graphics and photographs Two values are available for the Neutral Grays setting e Black Only generates neutral colors grays and black by using only black toner This guar
158. ear Manage printer color options on Windows computers 149 Manage printer color options on Macintosh computers Setting the color options to Automatic typically produces the best possible print quality for the most common printing requirements However for some documents setting the color options manually can enhance the way the document appears Examples of these documents include marketing brochures that contain many images or documents that are printed on a media type that is not listed in the printer driver Print color as gray or change the color options by using the Color Options pop up menu in the Print dialog box For more information about how to gain access to the printer drivers see Select the correct printer driver Print Color as Gray Selecting the Print Color as Gray option from the printer driver prints a document in black and shades of gray This option is useful for previewing preliminary copies of slides and hardcopy output or for printing color documents that will be photocopied or faxed Setting the color options in Macintosh Use the Color Options pop up menu to control how colors are interpreted and printed from software programs ET NOTE For more information about using the color options see Manage printer color options on Macintosh computers To set the color options 1 Open the printer driver see Select the correct printer driver 2 Open the Color Options pop up menu 3 Ifyou ar
159. ecifies in the materials shipped with a replacement CSR part whether a defective part must be returned to HP In cases where it is required to return the defective part to HP you must ship the defective part back to HP within a defined period of time normally five 5 business days The defective part must be returned with the associated documentation in the provided shipping material Failure to return the defective part may result in HP billing you for the replacement With a customer self repair HP will pay all shipping and part return costs and determine the courier carrier to be used Customer self repair warranty service 303 HP customer care Online services For 24 hour access to information by using a modem or Internet connection World Wide Web Updated HP printer software product and support information and printer drivers in several languages can be obtained from http www hp com support ljcm4 7 30mfp The site is in English Online troubleshooting tools HP Instant Support Professional Edition ISPE is a suite of Web based troubleshooting tools for desktop computing and printing products ISPE helps you quickly identify diagnose and resolve computing and printing problems The ISPE tools are available at http instantsupport hp com Telephone support Hewlett Packard Company provides free telephone support during the warranty period When you call you will be connected to a responsive team that is waiting to help y
160. egrees or flip it over and then reload it into the tray EZ NOTE Do not fan media Fanning can cause static electricity which can cause media to stick together Media does not meet the specifications for this MFP Use only media that meets HP media specifications for this MFP Trays are not properly adjusted Make sure that the rear media length guide indicates the length of media being used Printer feeds incorrect page size Printer feeds incorrect page size Cause Solution The correct size media is not loaded in the input tray Load the correct size media in the input tray The correct size media is not selected in the software program or printer driver The correct size media for tray 1 is not selected in the MFP control panel Confirm that the settings in the software program and printer driver are appropriate since the software program settings override the printer driver and control panel settings and the printer driver settings override the control panel settings For more information see Select the correct printer driver From the control panel select the correct size media for tray 1 The media size is not configured correctly for the input tray Print a configuration page or use the control panel to determine the media size for which the tray is configured The guides in the tray are not against the paper Verify that the rear and width media guides are t
161. el is missing HP print cartridge from a print cartridge 11 XX Internal clock error To continue The MFP real time clock has experienced an Whenever the MFP is turned off and then touch OK error turned on again set the time and date at the control panel See Use the control panel Ifthe error persists you might need to replace the formatter 13 01 00 JAM IN TRAY 1 Paper is jammed in tray 1 1 Follow the onscreen instructions to find and remove the jammed media 2 Ifthe message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 13 01 11 JAM INSIDE LOWER RIGHT There is a paper jam inside the lower right 1 Follow the onscreen instructions to find DOOR door or the paper did not feed from the paper and remove the jammed media tray 2 Ifthe message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 13 02 00 JAM INSIDE RIGHT DOORS There is a paper jam inside the right doors Follow the onscreen instructions to find and remove the jammed media 2 Ifthe message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 13 05 00 JAM INSIDE RIGHT DOORS There is a paper jam inside the right doors Follow the onscreen instructions to find and remove the jammed media 2 Ifthe message persists after clearing all pages contact HP Support at http www hp
162. emory 64MB on the board and 256MB installed for a total of 320MB to store customer data during the printing and copying process When the MFP is powered off this volatile memory is erased Non volatile memory The MFP utilizes non volatile memory EEPROM to store system control data and user preference settings No customer print or copy data is stored in non volatile memory This non volatile memory can be cleared and restored to factory defaults by performing a Cold Reset or Restore Factory Defaults from the control panel Hard disk drive memory The MFP contains an internal hard disk drive 40GB or larger that may retain data after the MFP is powered off The MFP also may contain additional optional compact flash storage or an external EIO hard disk Data stored in these devices may be from incoming outgoing fax or email files stored copy or print jobs fax or email address books or third party solutions Some of this data can be erased from the control panel of the MFP but most must be erased using the Secure Storage Erase features available within HP Web Jetadmin Secure Storage Erase features comply with U S Department of Defense DOD specification 5220 22 M 324 Appendix D Regulatory information ENWW Safety statements Laser safety The Center for Devices and Radiological Health CDRH of the U S Food and Drug Administration has implemented regulations for laser products manufactured since August 1 1976 Compliance is ma
163. end a fax in one of three ways e LAN fax sends faxes through a third party fax provider e Microsoft Windows 2000 fax is a fax modem and Digital Sender Module on a computer that allows the computer to operate as a turnkey gateway fax e Internet fax uses an Internet fax provider to process faxes and the fax is delivered on a traditional fax machine or sent to the user s e mail For complete information about using digital faxing see the documentation that is provided with the HP Digital Sending Software 180 Chapter 13 Fax ENWW 14 Manage the MFP ENWW Information pages Embedded Web server HP Easy Printer Care software HP Web Jetadmin software HP Printer Utility for Macintosh Security features Set the real time clock Configure alerts Upgrade the firmware Manage memory Manage supplies 181 Information pages Information pages provide details about the device and its current configuration The following table provides the instructions for printing the information pages Page description How to print the page from the MFP control panel Menu map Shows the control panel menus and available settings 1 From the Home screen touch Administration 2 Touch Information 3 Touch Configuration status Pages 4 Touch Administration Menu Map 5 Touch Print The content of the menu map varies depending on the options currently installed in the device For a complete li
164. er driver features e Staple documents e Cancela print job ENWW 113 Media type and tray loading Minimum media dimensions are 76 x 127 mm 3 x 5 inches Maximum media dimensions are 216 x 356 mm 8 5 x 14 inches Table 9 1 Tray 1 media information Media type Media Media quantity Driver settings Paper orientation Output specifications Paper and Range Maximum stack Plain or N A cardstock height 10 mm 0 6 unspecified standard sizes 60 g m 16 Ib inch bond to 220 g m 60 Ib bond Equivalent to 100 sheets of 75 g m 20 Ib bond Envelopes Less than 60 g m Upto 20 envelopes Envelope Short edge 16 Ib bond to 90 leading flap on g m 24 Ib bond right side facing up Labels Maximum 0 23 mm Maximum stack Labels Side to be printed 0 009 in thick height 10 mm 0 6 on facing up inch Transparencies Minimum 0 13 mm Maximum stack Transparencies Side to be printed 0 005 in thick height 10 mm 0 6 on facing up inch Heavy 0 13 mm 0 005 Maximum stack Light glossy Side to be printed in thick height 10 mm 0 6 glossy or heavy on facing up in glossy Glossy Range Maximum stack Light glossy Side to be printed 75 g m 20 Ib bond to 220 g m 60 Ib bond height 10 mm 0 6 in glossy or heavy glossy on facing up Table 9 2 Tray 2 tray 3 and tray 4 media information Media type Media Media quantity Driver settings Paper orientation Output specifications Paper and
165. er utility 2 Select HP Color LaserJet CM4730 3 On the File menu click Show Info ENWW Macintosh printer driver features 131 6 Select the Installable Options tab Scroll to Accessory Output Bins and select HP 500 sheet stapler stacker or HP 700 sheet 3 bin Mailbox Click Apply Changes Set the color options Use the Color Options pop up menu to control how colors are interpreted and printed from software programs 1 2 3 4 5 On the File menu in the software program click Print Select the driver and then click Properties or Preferences Open the Color Options pop up menu If you are using Mac OS X click Show Advanced Options Adjust the individual settings for text graphics and photographs Use the Services menu If the device is connected to a network use the Services menu to obtain device and supply status information 1 Onthe File menu click Print 2 Open the Services menu 3 Select a maintenance task from the drop down list and then click Launch The embedded Web server opens to the page that provides the information for the task that you selected 4 Togo to various support Web sites for this device select an Internet Services option from the drop down list and then click Go 132 Chapter9 Print tasks ENWW Staple documents The optional stapler stacker has the following specifications It can staple jobs of up to 30 sheets of 75 g m 20 Ib paper It can staple letter size
166. ered is not a valid folder The folder name was entered incorrectly or the folder does not exist Re enter the folder name correctly or add the folder There might be a document on the glass If there is remove it then press Start A digital send or copy job has been performed from the scanner glass but the original document needs to be removed Remove the original document from the scanner glass and press Start TOO MANY PAGES IN JOB TO STAPLE The maximum number of sheets the stapler can staple is 30 For print jobs that have more than 30 pages staple them manually Type Mismatch In Tray XX The specified tray contains a media type that does not match the configured type The specified tray will not be used until this condition is addressed Printing can continue from other trays ENWW Control panel messages 237 Table 16 1 Control panel messages continued Control panel message Description Recommended action Unable to connect To temporarily hide this message in order to fax or send to e mail touch Hide If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support ljcm4730mfp UNABLE TO COPY The MFP was unable to copy the document If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http Awww hp com support licm4730m
167. es 6 ETB 75 mm 2 95 inches 7 Fuser 76 0 mm 2 99 inches 8 Fuser 81 0 mm 3 19 inches 9 Print cartridge 94 2 mm 3 71 inches To identify if the print cartridge is the problem insert a print cartridge from another HP Color LaserJet CM4730 MFP series if one is available before ordering a new print cartridge If the defect repeats at 94 0 mm 3 75 inch intervals try replacing the print cartridge before replacing the fuser 286 Chapter 16 Problem solving ENWW Solve fax problems For help solving fax problems go to http www hp com go mfpfaxaccessory300 You can also refer to the Analog Fax Accessory 300 Fax Guide and the Analog Fax Accessory 300 Send Fax Driver Guide which are included on the MFP software CD ENWW Solve fax problems 287 Solve e mail problems If you are unable to send e mails by using the digital send feature you might need to reconfigure the SMTP gateway address or the LDAP gateway address Print a configuration page to find the current SMTP and LDAP gateway addresses See Information pages Use the following procedures to check if the SMTP and LDAP gateway addresses are valid Validate the SMTP gateway address ET NOTE This procedure is for Windows operating systems 1 Open an MS DOS command prompt click Start click Run and then type cmd 2 Type telnet followed by the SMTP gateway address and then the number 25 which is the port over which the MFP is communi
168. es between transparencies Transparency mode and paper Normal mode e This is the fastest mode and is useful for high volume printing in Normal mode Select the media by source type or size In the Microsoft Windows operating system three settings affect how the printer driver tries to pull media when you send a print job Source Type and Size settings appear in the Page Setup Print or Print Properties dialog boxes in most software programs Unless you change these settings the MFP automatically selects a tray using the default settings Source To print by Source select a specific tray from MFP to pull from The MFP tries to print from this tray no matter what type or size is loaded If you select a tray that is configured for a type or size that does not match your print job the MFP does not print automatically Instead it waits for you to load the tray with the type or size of print media for your print job If you load the tray the MFP begins printing Type and Size Printing by Type or Size means that you want the MFP to pull from the tray that is loaded with the correct type and size of media Selecting media by type rather than source is similar to locking out trays and helps protect special media from accidental use For example if a tray is configured for letterhead and you select plain paper the MFP will not pull the letterhead from that tray Instead it will pull from a tray that has plain paper loaded and is configure
169. escription General Copy Scan Ahead Enabled default Turn on no wait scanning With Scan Ahead Behavior enabled the pages in the original document Disabled are scanned to disk and held until the device becomes available Auto Print Interrupt Enabled When this feature is enabled copy jobs can interrupt print jobs that are set to print multiple Disabled default copies The copy job is inserted into the print queue at the end of one copy of the print job After the copy job is complete the device continues printing the remaining copies of the print job Copy Interrupt Enabled When this feature is enabled a copy job that is currently printing can be interrupted when Disabled default a new copy job is started You are prompted to confirm that you want to interrupt the current job First Copy Speed No early warm up default Early warm up Alternative No default Letterhead Mode Yes ENWW Device Behavior menu 45 Table 2 15 Device Behavior menu continued Menu item Sub menu item Sub menu item Values Description General Printing Behavior Override A4 Letter Manual Feed No Yes default Enabled Disabled default When this feature is enabled the job prints on letter size paper when an A4 job is sent but no A4 size paper is loaded in the device or prints on A4 paper when a letter size job is sent but no letter size paper is loaded This option also overrides A3 with ledger size
170. ete the following procedure to clear a jam in the output accessory bridge 1 Open the cover to the output accessory bridge 2 Push down on the green lever remove any media inside the output accessory bridge and push the green lever up 3 Close the cover to the output accessory bridge 4 Ifthe jam still does not clear grasp the handle on the output accessory bridge and slide the output accessory bridge away from the MFP ENWW Jams 253 5 Look for paper on top of the output accessory bridge 6 Slide the output accessory bridge back into the MFP 7 Slide the 3 bin mailbox or stapler stacker back into the MFP Clear jams in the ADF 1 Open the ADF cover EZ NOTE Aplastic sheet is placed on the electrostatic transfer belt to protect it during shipping When the MFP is powered up for the first time the plastic sheet is sent to the output tray 254 Chapter 16 Problem solving ENWW 2 Remove any jammed media 3 ENWW Jams 255 Media handling problems Use only media that meets the specifications outlined in the HP LaserJet Printer Family Print Media Guide Printer feeds multiple sheets Printer feeds multiple sheets Cause Solution The input tray is overfilled Remove excess media from the input tray Print media is sticking together Remove media flex it rotate it 180 d
171. for the sanitization of disk media Security features 197 Data affected Data affected covered by the Secure Disk Erase feature includes temporary files that are created during the print and copying process stored jobs proof and hold jobs disk based fonts disk based macros forms stored fax files address books and HP and third party applications ET NOTE Stored jobs will be securely overwritten only when they have been deleted through the Retrieve Job menu on the MFP after the appropriate erase mode has been set This feature will not impact data that is stored on flash based product non volatile RAM NVRAM that is used to store default settings page counts and similar data This feature does not affect data that is stored on a system RAM disk if one is used This feature does not impact data that is stored on the flash based system boot RAM Changing the Secure Disk Erase mode does not overwrite previous data on the disk nor does it immediately perform a full disk sanitization Changing the Secure Disk Erase mode changes how the MFP cleans up temporary data for jobs after the erase mode has been changed Gain access to Secure Disk Erase Use HP Web Jetadmin to gain access to and set the Secure Disk Erase feature Additional Information For additional information about the HP Secure Disk Erase feature see the HP support flyer or go to http www hp com go webjetadmin DSS authentication Optional Digital Sendin
172. fore users are affected Download this free enhanced management software at http www hp com go webjetadmin software To obtain plug ins to HP Web Jetadmin click plug ins and then click the download link that is next to the name of the plug in that you want The HP Web Jetadmin software can automatically notify you when new plug ins are available On the Product Update page follow the directions to automatically connect to the HP Web site If installed on a host server HP Web Jetadmin is available to any client through a supported Web browser such as Microsoft Internet Explorer 6 0 for Windows or Netscape Navigator 7 1 for Linux Browse to the HP Web Jetadmin host ET NOTE Browsers must be Java enabled Browsing from an Apple Macintosh computer is not supported 190 Chapter 14 Manage the MFP ENWW HP Printer Utility for Macintosh Use the HP Printer Utility to configure and maintain a printer from a Mac OS X V10 2 V10 3 or V10 4 computer This section describes several functions that you can perform through the HP Printer Utility Open the HP Printer Utility The process that you use to start the HP Printer Utility depends on the Macintosh operating system that you are using Open the HP Printer Utility in Mac OS X V10 2 1 Open the Finder and then click Applications 2 Click Library and then click Printers 3 Click hp and then click Utilities 4 Double click HP Printer Selector to open the HP Printer Selector 5
173. fp To temporarily hide this message in order to fax or send to e mail touch IGNORE UNABLE TO SEND To temporarily hide this message in order to fax or send to e mail touch IGNORE If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support licm4730mfp Unable to send Fax Please check fax configuration The MFP was unable to send the fax Contact the network administrator UNABLE TO SEND JOB To temporarily hide this message in order to fax or send to e mail touch IGNORE If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support licm4730mfp Unauthorized supply in use The MFP is using a non HP supply If you believe you purchased a genuine HP supply go to http www hp com go anticounterfeit Any printer repair required as a result of using non HP or unauthorized supplies is not covered under warranty HP cannot ensure the accuracy or the availability of certain features User name or password is incorrect Please re enter The user name or password was typed incorrectly Retype the user name and password User Name Job Name or PIN is missing One or more of the required items has not been selected or typed Select the correct user name and job name and type the correct PIN 238 Chapter 16 Problem solv
174. fter replacing the kit reset the ADF maintenance kit count Reset the ADF maintenance kit count ENWW 1 2 3 4 5 6 On the control panel scroll to and touch Administration Touch Resets Touch Reset Supplies Touch ADF Maintenance Kit Touch Yes Touch Save ADF maintenance kit 219 Calibrate the scanner Calibrate the scanner to compensate for offsets in the scanner imaging system carriage head for ADF and flatbed scans Because of mechanical tolerances the scanner s carriage head might not read the position of the image accurately During the calibration procedure scanner offset values are calculated and stored The offset values are then used when producing scans so that the correct portion of the document is captured Scanner calibration should be carried out only if you notice offset problems with the scanned images The scanner is calibrated before it leaves the factory It needs to be calibrated again only rarely Before calibrating the scanner print the calibration target 1 2 3 4 5 6 10 Place letter or A4 size paper in tray 1 and adjust the side guides On the control panel Home screen scroll to and touch Administration Touch Troubleshooting Touch Calibrate Scanner Touch Calibrate to print the first pass of the calibration target Place the first pass of the calibration target face down in tray 1 so that the arrows are facing into the MFP Touch Start to print the second pass
175. g boxes e Printer control panel settings Settings changed at the printer control panel have a lower priority than changes made anywhere else 66 Chapter 3 Software for Windows ENWW Open the printer drivers Operating System To change the settings for all print jobs until the software program is closed Windows 2000 XP 1 Server 2003 and software program click Vista Print 2 Select the driver and then click Properties or Preferences The steps can vary this procedure is most common On the File menu in the 1 for all print jobs Click Start click Settings and then click Printers Windows 2000 or Printers and Faxes Windows XP Professional and Server 2003 or Printers and Other Hardware Devices Windows XP Home For Windows Vista click Start click Control Panel and then click Printer To change the default settings To change the device configuration settings Click Start click Settings and then click Printers Windows 2000 or Printers and Faxes Windows XP Professional and Server 2003 or Printers and Other Hardware Devices Windows XP Home For Windows Vista click Start click Control Panel and then click Printer 2 Right click the driver icon Right click the driver icon and then select Printing and then select Preferences Properties Click the Device Settings tab Mac OS X V10 2 8 1 On the File menu click 1 On the File menu click In the Finder on the Go V10
176. g is recommended for printing all color documents Select Manual to manually adjust the color and halftone modes for text graphics and photographs If you are using a PCL driver you can adjust the RGB data If you are using the PS driver you can adjust RGB or CMYK data To set the color options 1 2 3 4 5 6 Open the printer driver Click the Color tab In the Color Options area select the option that you want to use If you selected Manual click Settings to open the Color Settings dialog box Adjust the individual settings for text graphics and photographs You can also adjust the general printing settings Click OK In the Color Themes area select the RGB Color option that you want to use Click OK RGB Color Color Themes Five values are available for the RGB Color setting ENWW Select Default SRGB for most printing needs This setting instructs the printer to interpret RGB color as sRGB which is the accepted standard of Microsoft and the World Wide Web Consortium W3C Select Image optimization SRGB to enhance documents in which the content is mainly bitmap images such as GIF or JPEG files This setting instructs the printer to use the best color matching for rendering sRGB bitmap images This setting has no effect on text or vector based graphics Using glossy media in combination with this setting provides the maximum enhancement Manage printer color options on Windows computers 147
177. g Software DSS for the MFP is available for purchase separately The software provides an advanced sending program that contains an authentication process This process requires users to type a user identification and a password before they can use any of the DSS features that require authentication Lock the control panel menus To prevent someone from changing the MFP configuration you can lock the control panel menus This prevents unauthorized users from changing the configuration settings such as the SMTP server The following procedure describes how to restrict access to the control panel menus by using the HP Web Jetadmin software See HP Web Jetadmin software 1 Open the HP Web Jetadmin program 2 Open the DEVICE MANAGEMENT folder in the drop down list in the Navigation panel Navigate to the DEVICE LISTS folder Select the MFP In the Device Tools drop down list select Configure Select Security from the Configuration Categories list Type a Device Password DU dg Qu dms In the Control Panel Access section select Maximum Lock This prevents unauthorized users from gaining access to configuration settings 198 Chapter 14 Manage the MFP ENWW Set the real time clock Use the real time clock feature to set the date and time settings The date and time information is attached to stored print fax and digital send jobs so you can identify the most recent versions of stored print jobs Set the date format 1
178. ge 253 right covers 241 staple jams 249 stapler stacker 248 tray 1 246 trays 2 3 4 246 parallel configuration 78 parallel port features 7 locating 11 part numbers memory 300 print cartridges 299 pausing a print request 136 PCL drivers universal 64 permanent storage errors 231 personal jobs 109 phone line connecting fax accessory 178 phone numbers ordering supplies 304 service agreements 305 support 304 photos copying 162 loading 169 physical specifications 311 PINs personal jobs 109 plastic sheet 254 ports included 7 locating 11 troubleshooting Macintosh 293 PostScript Printer Description PPD files included 70 power specifications 313 troubleshooting 222 power switch locating 9 PPDs included 70 print cartridge authentication 207 checking toner levels 208 genuine HP 207 life expectancy 208 managing 207 non HP 207 replacing 211 storing 207 print cartridges error messages 234 Macintosh status 132 management menu 29 ordering 304 part numbers 299 recycling 320 status viewing with embedded Web server 185 warranty 306 ENWW Print Document On 118 print media for color printing 140 loading in tray 1 93 print quality color fade 271 272 fingerprints 273 horizontal lines 266 loose toner 274 media damage 277 misaligned colors 268 repetitive defects 270 skewed page 279 smeared toner 275 specs 278 troubleshooting 263 vertical lines 269 white areas 276 print server card installing 340 printta
179. ght specifications for this product Do not use paper that is heavier than the recommended media specification for this product unless itis HP paper that has been approved for use in this product Glossy or coated paper Use only glossy or coated paper that is approved for use in laser printers Do not use glossy or coated paper designed for use in inkjet products 92 Chapter7 Paper and print media ENWW Load paper and print media You can load different media in the trays and then request media by type or size by using the control panel Load tray 1 AN CAUTION To avoid jams never add or remove media from tray 1 during printing 1 Open tray 1 2 Set the side guides to the desired width 3 Load media in the tray with the side to be printed on face down and the top of the media or non postage end facing you 4 Makesure the stack fits under the tabs on the guides and does not exceed the load level indicators 5 Adjust the side guides so that they lightly touch the media stack but do not bend it If your software does not automatically format an envelope specify Landscape for page orientation in your software program or printer driver Use the following guidelines to set margins for return and destination addresses on Commercial 10 or DL envelopes ENWW Load paper and print media 93 Address type Left margin Top margin Return 15 mm 0 6 inches 15 mm 0 6 inches
180. halftone settings for text graphics and photographs independently The two halftone options are Smooth and Detail e The Smooth option provides better results for large solid filled print areas It also enhances photographs by smoothing out fine color gradations Choose this option when uniform and smooth area fills are top priority e The Detail option is useful for text and graphics that require sharp distinctions among lines or colors or for images that contain a pattern or a high level of detail Choose this option when sharp edges and details are top priority ET NOTE Some software programs convert text or graphics to bitmap images In these cases setting the color options for Photographs also affects how text and graphics appear Neutral Grays The Neutral Grays setting determines the method used for creating gray colors that are used in text graphics and photographs Two values are available for the Neutral Grays setting e Black Only generates neutral colors grays and black using only black toner This guarantees neutral colors without a color cast e 4 Color generates neutral colors grays and black by combining all four toner colors This method produces smoother gradients and transitions to non neutral colors and it produces the darkest black ET NOTE Some software programs convert text or graphics to raster images In these cases setting the color options for Photographs also affects how text and graphics app
181. he file in ASCII format instead of binary encoding You are unable to print from a third party USB card Cause Solution This error occurs when the software for USB printers is not installed When adding a third party USB card you might need the Apple USB Adapter Card Support software The most current version of this software is available from the Apple Web site When connected with a USB cable the printer does not appear in the Print Center or Printer Setup Utility after the driver is selected Cause Solution This problem is caused by either a software or a hardware component Software troubleshooting e Check that your Macintosh supports USB e Verify that your Macintosh operating system is Mac OS X v10 1 or later e Ensure that your Macintosh has the appropriate USB software from Apple ENWW Solve common Macintosh problems 293 Table 16 7 Problems with Mac OS X continued When connected with a USB cable the printer does not appear in the Print Center or Printer Setup Utility after the driver is selected Cause Solution Hardware troubleshooting Check that the printer is turned on Verify that the USB cable is connected correctly Check that you are using the appropriate high speed USB cable Ensure that you do not have too many USB devices drawing power from the chain Disconnect all of the devices from the chain and connect the cable directly to the USB port on the host computer
182. he following procedure to load staples 1 Press and hold the release button on the top of the stapler stacker Pull the stapler stacker away from the MFP 134 Chapter9 Print tasks ENWW 2 Open the staple cartridge cover 4 nsert the new staple cartridge into the stapler unit and push down on the green handle until the unit snaps into place ENWW Staple documents 135 Cancel a print job You can stop a print request by using the control panel or by using the software program For instructions about how to stop a print request from a computer on a network see the online Help for the specific network software E NOTE tcan take some time for all printing to clear after you have canceled a print job Stop the current print job from the control panel 1 Press Stop on the control panel 2 Onthe touchscreen on the Device Has Been Paused screen touch Cancel current job EZ NOTE If the print job is too far into the printing process you might not have the option to cancel it Stop the current print job from the software program A dialog box will appear briefly on the screen giving you the option to cancel the print job If several requests have been sent to the device through your software they might be waiting in a print queue for example in Windows Print Manager See the software documentation for specific instructions about canceling a print request from the computer If a print job is waiting in a
183. he media size for which the tray is configured The guides in the tray are not against the paper Verify that the guides are touching the paper Transparencies or glossy paper will not feed Transparencies or glossy paper will not feed Cause Solution The correct media type is not specified in the software or printer Verify that the correct media type is selected in the software or driver printer driver The input tray is overfilled Remove excess media from the input tray Do not load more than 200 sheets of glossy paper or glossy film or more than 100 transparencies in tray 2 3 or 4 Do not exceed the maximum stack height for tray 1 Media in another input tray is the same size as the Make sure that the input tray containing the transparencies or transparencies and the MFP is defaulting to the other tray glossy paper is selected in the software program or printer driver Use the MFP control panel to configure the tray to the media type loaded The tray containing the transparencies or glossy paper is not Make sure that the input tray containing the transparencies or configured correctly for type glossy paper is selected in the software program or printer driver Use the MFP control panel to configure the tray to the media type loaded Transparencies or glossy paper might not meet supported Use only media that meets the HP media specifications for this media specifications MFP Envelopes jam or will
184. his feature Click Find Server to find the LDAP server on your network then click Test near the bottom of the page to test access to the server Contact your network administrator for more information about using the LDAP server e Address Book page Use this page to import e mail addresses in the form of a Comma Separated Value CSV file into the MFP internal address book This process is necessary only if you are not using an LDAP server to find e mail addresses e Activity Log page View the digital sending activity log for the MFP The log contains digital sending job information including any errors that occur e Preferences page Configure digital sending defaults such as the default page size and the default settings reset delay You can also configure these settings by using the MFP control panel menus Networking tab The network administrator can use this tab to control network related settings for the MFP when it is connected to an IP based network This tab does not appear if the MFP is directly connected to a computer or if the MFP is connected to a network with anything other than an HP Jetdirect print server Other links This section contains links that connect you to the Internet You must have Internet access in order to use any of these links If you use a dial up connection and did not connect when you first opened the 186 Chapter 14 Manage the MFP ENWW ENWW embedded Web server you must connect before you can vi
185. ht corner of the window Select Update Printer Firmware from the action list If the name of the RFU file is not listed in the All Available Images box click Browse in the Upload New Firmware Image dialog box and navigate to the location of the RFU file that you downloaded from the Web at the start of this procedure If the filename is listed select it Click Upload to move the RFU file from your hard drive to the HP Web Jetadmin server After the upload is complete the browser window refreshes Select the RFU file from the Printer Firmware Update drop down menu Click Update Firmware HP Web Jetadmin sends the selected RFU file to the MFP The control panel shows messages that indicate the progress of the upgrade At the end of the upgrade process the control panel shows the Ready message Use MS DOS commands to upgrade the firmware To update the firmware by using a network connection follow these instructions 1 From a command prompt or in an MS DOS window type the following copy B FILENAME COMPUTERNAME gt SHARENAME gt where FILENAME is the name of the RFU file including the path lt COMPUTERNAMES gt is the name of the computer from which the MFP is being shared and SHARENAME is the MFP share name For example C N copy b C 9200fW RFU NYOUR SERVERNVYOUR COMPUTER 344 EA NOTE Ifthe file name or path includes a space you must enclose the file name or path in quotation mark
186. i meplr iiacsece ederent ta Ete etn Leti d aen coe dae dtr dax nadie saadidddasbaandidavasauaaduacdanennacneeds 18 Default Job Options menu sssssssssssssssesssssesene eren ener rem rs nns n nsn nnne nnn nennen nnn inr n nsn aiaa 20 Default Options for Originals 1 cene hee Dg nene a ddp aa EU Dru et LA 20 MAGES ufui c 21 BI IUgeeoae cT EEEUOERRTESE 22 Defa lt Fax Optom c i 23 Default E mail Options creed ren een rentre eeu echinacea 24 Default Send to Folder Options sssssssssssssssssseee eene nennen 25 Default Print Optlons cR 26 Time Scheduling menu ec ee ere nr ne ne eee ener innen nemen ird n nnne n e rennen 27 Management men ciae eite tere She E eee Pape rur ee Ra RB e eS aaO Rp RAA 29 initial Setup Menu sisine DO LOUPE 31 Networking and I Q trc E eee ret E A 31 ESSI 39 E iMall SetUp aiiin a aa aaa aaa a a a a aiaa iia 42 Send Setup mel 5 Iri aaa aa a Rd a aaa 42 Device Behavior menu c eecceeceeceeeeeeeeeeeeeeeeetee ce tE nere rer emet n nnns en nnne denn nnne n nnn n nenne rnrrtr innen nens 43 Print Quality MON e 48 Troubleshooting menu 0 0 00 cee ter eee nr ne eene nennen eren aA NEATA A kadra nsn dn nre aaa nennen nene 50 iii FRRESGtS BI EU DU TDRUM
187. ide of the page is printed upside down This option is for print jobs that are bound along the top edge 26 Chapter 2 Control panel ENWW Time Scheduling menu Administration gt Time Scheduling Use this menu to set options for setting the time and for setting the device to enter and exit sleep mode ET NOTE Values shown with default are the factory default values Some menu items have no default Table 2 8 Time Scheduling menu Menu item Sub menu item Sub menu item Values Description Date Time Date Format YYYY MMM DD Use this feature to set the current date and default time and to set the date format and time format that are used to time stamp outgoing MMM DD YYYY faxes DD MMM YYYY Date Month Day Year Time Format 12 hour AM PM default 24 hour Time Hour Minute AM PM Sleep Delay 1 Minute Use this feature to selectthe time interval that the device should remain inactive before 20 minutes entering Sleep Mode 30 minutes default 45 minutes 1 hour 60 minutes 90 minutes 2 hours 4 hours Wake Time Monday Off default Select Custom to set a wake time for each day ofthe week The device exits sleep mode Tuesday Custom according to this schedule Using a sleep schedule helps conserve energy and Wednesday prepares the device for use so that users do not have to wait for it to warm up Thursday Friday ENWW Time Scheduling menu 27 Table 2 8 Time Scheduling menu continued
188. ies One or more supplies needs to be replaced 1 Replace the supply Order Transfer Kit The transfer kit is near end of life Printing can continue Order a replacement transfer kit Output bin x full The specified output bin is full and printing cannot continue Empty the bin to continue printing Output paper path open The paper path between the MFP and the output device is open and must be closed before printing can continue 1 If you have a 3 bin mailbox installed make sure the jam access door is closed 2 Ifyou have a stapler stacker installed make sure the staple cartridge is snapped into position and that the staple cartridge door is closed Password or name is incorrect Please enter correct login The user name or password was typed incorrectly Retype the user name and password Performing Color Band Test The color band test is being performed No action is necessary PIN is incorrect Please re enter PIN The PIN was typed incorrectly Retype the PIN Please turn device off and install hard disk The requested job requires a hard disk but the MFP does not have a hard disk installed Turn the MFP off and install a hard disk Printing CMYK Samples The CMYK samples page is being generated The device will return to the ready state upon completion of the page No action is necessary Printing Color Usage Log The color usage log page i
189. ies Information dialog box appears e Toorder supplies online click Order HP Supplies You must have Internet access in order to use the online ordering Web page For more information about online ordering see Order supplies online and use other support features Order supplies online and use other support features Use the HP Web site to order printer supplies register the printer get customer support or learn about recycling printer supplies You must have Internet access in order to use the supplies and support Web pages 1 Open the HP Printer Utility 2 Inthe Configuration Settings list select HP Support 3 Click one of the following buttons e Instant Support Opens a Web page that you can use to seek technical assistance e Order Supplies Online Opens a Web page that you can use to order printer supplies e Online Registration Opens a Web page that you can use to register the printer e Return amp Recycle Opens a Web page that you can use to find information about recycling used supplies Upload a file to the printer Send a file from the computer to the printer The action that the printer takes depends on the type of file that is being sent to it For example when a print ready file such as a PS or PCL file is sent the printer prints the file 1 2 3 Open the HP Printer Utility In the Configuration Settings list select File Upload Click Choose navigate to the file that you want to upload and
190. iewer to view the e mail attachment For information about changing the settings for the current job see Change e mail settings for the current job Send a document ENWW 1 Place the document face down on the scanner glass or face up in the ADF 2 From the Home screen touch E mail 3 f prompted type your user name and password 4 Complete the From To and Subject fields Scroll down and complete the CC BCC and Message fields if appropriate Your user name or other default information might appear in the From field If so you might not be able to change it 5 Optional Touch More Options to change the settings for the document that you are sending for example the document s original size If you are sending a two sided document you should select Sides and an option with a two sided original 6 Press Start to begin sending 7 When you are finished remove the original document from the scanner glass or ADF Perform basic e mail functions 169 Use the auto complete function When you type characters into the To CC or From fields on the Send E mail screen the auto complete function is activated As you type the required address or name by using the keyboard screen the device automatically searches the address book list and completes the address or name by using the first match You can then select that name by touching Enter or continue typing the name until auto complete finds the correct entry If
191. igh or too low Use paper from a different source or from an unopened ream of paper Some areas of the paper reject toner Use paper from a different source or from an unopened ream of paper The letterhead you are using is printed on rough paper Use a smoother xerographic paper If this solves your problem consult with the printer of your letterhead to verify that the paper used meets the specifications for this MFP Color printing problems Printout color error ENWW Table 16 2 Printing black instead of color cause and solution Cause Solution Color mode is not selected in the software program or printer Select Color mode instead of Grayscale or Monochrome driver mode in the software program or printer driver The correct printer driver is not selected in your software Select the correct printer driver program No color appears on the configuration page Consult your service representative Correct print quality and copy quality problems 263 Incorrect shade Table 16 3 Incorrect shade cause and solution Cause Solution The media does not meet the specifications for this MFP Use media that meets HP media specifications You are operating the MFP in excessively humid conditions Verify that the MFP s environment is within humidity specifications Missing color Table 16 4 Missing color cause and solution Cause Solution Defective HP print cartridge Replace the cartridge A non HP
192. igher values represent darker shadows on a printed page 5 to 5 Default is 0 Set Registration Test Page Print Shift the margin alignment to center the image on the page from top to bottom and from left to right You can also align the image on the front with the image printed on the back Print a test page for setting the registration Source All trays Select the source input tray for printing the Set Tray X contents choose a tray Registration page Adjust Tray X Shift from 20 to 20 along the X or Y axes 0 is the default Perform the alignment procedure for each tray When it creates an image the device scans across the page from side to side as the sheet feeds from top to bottom into the device The scan direction is referred to as X X1 is the scan direction for the first side of a 2 sided page X2 is the scan direction for the second side of a 2 sided page The feed direction is referred to as Y Print Modes Paper Type Configure which mode is associated with which paper type Auto Sense Mode Tray 1 Autosense Full Sensing default Expanded Sensing Transparency Only When Expanded Sensing is selected the device recognizes normal paper overhead transparencies glossy paper and tough paper When Transparency Only is selected the device recognizes only overhead transparency and non overhead transparency types Tray 2 4 Sensing 48 Chapter2 Control panel Expanded
193. ight door or inside the fusing unit 1 Follow the onscreen instructions to find and remove the jammed media 2 Ifthe message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 1 Follow the onscreen instructions to find and remove the jammed media 2 Ifthe message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 13 XX YY EXTERNAL OUTPUT DEVICE PAPER JAM There is a jam in the stapler stacker 1 Follow the onscreen instructions to find and remove the jammed media 2 Ifthe message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 13 XX YY JAM IN OUTPUT AREA There is a paper jam in the output area 1 Follow the onscreen instructions to find and remove the jammed media 2 Ifthe message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 13 XX YY JAM IN OUTPUT DEVICE Paper is jammed in an external paper handling device 1 Follow the onscreen instructions to find and remove the jammed media 2 Ifthe message persists after clearing all pages contact HP Support at http www hp com support ljcm4730mfp 13 XX YY Jam In Stapler A staple is jammed in the stapler Check the stapler stacker for jammed staples 1 Follow the onscreen instructions to find and remove the jammed medi
194. in the following pop up menus or fields e Configuration e Host Name e IP Address e Subnet Mask e Default Gateway If you want to change more settings in the embedded Web server click Additional Network Settings The embedded Web server opens with the Networking tab selected Click Apply Now Open the embedded Web server 1 2 3 Open the HP Printer Utility In the Configuration Settings list select Additional Settings Click Open Embedded Web Server 194 Chapter 14 Manage the MFP ENWW Set up e mail alerts ENWW Set up e mail messages that alert you to certain events that occur with the printer such as a low toner level in a print cartridge 1 2 3 4 Open the HP Printer Utility In the Configuration Settings list select E mail Alerts Click the Server tab and in the SMTP Server box type the server name Click the Destination tab click the add button and then type the e mail addresses mobile device numbers or Web site URLs to which you want the e mail alerts sent E NOTE If your printer supports e mail lists you can make alerts lists for specific events the same way that you added e mail addresses Click the Events tab and in the list define the events for which an e mail alert should be sent To test the alerts setup click the Server tab and then click Test A sample message is sent to the defined e mail addresses if the configuration is correct Click Apply Now HP Printer
195. ing ENWW Jams Use this illustration to troubleshoot paper jams in the printer For instructions on clearing paper jams see Jams ET NOTE Allareas of the MFP that might need to be opened to clear jams are equipped with green handles Figure 16 1 Paper jam locations 1 ADF access cover 2 ADF input tray 3 ADF output tray 4 Duplexer cover 5 Upper right door 6 Fuser cover 7 Transfer unit 8 Duplex paper path 9 Middle right door 10 Tray 1 multipurpose tray 11 Drawer below tray 1 ENWW Jams 239 12 Lower right door 13 Trays 2 3 and 4 14 Paper path 15 Output area Jam recovery This MFP automatically provides jam recovery a feature that you can use to automatically reprint jammed pages The following options are available e Auto The MFP attempts to reprint jammed pages e Off The MFP does not attempt to reprint jammed pages ET NOTE During the recovery process the MFP might reprint several good pages that were printed before the paper jam occurred Be sure to remove any duplicated pages To improve print speed and increase memory resources you might want to disable paper jam recovery If pa
196. ing MFP output color to your computer screen is quite complex because printers and computer monitors use different methods of producing color Monitors display colors by light pixels using an RGB red green blue color process but printers print colors using a CMYK cyan magenta yellow and black process Several factors can influence your ability to match printed colors to those on your monitor These factors include e Print media e Printer colorants inks or toners for example e Printing process inkjet press or laser technology for example e Overhead lighting e Personal differences in perception of color e Software programs e Printer drivers e Computer operating system e Monitors e X Video cards and drivers e Operating environment humidity for example Keep the above factors in mind when colors on your screen do not perfectly match your printed colors For most users the best method for matching colors on your screen to your MFP is to print SRGB colors PANTONE color matching PANTONE has multiple color matching systems PANTONE Matching System is very popular and uses solid inks to generate a wide range of color hues and tints See http www hp com support ljcm4730mfp for details on how to use PANTONE Matching System with this MFP ET NOTE PANTONE Colors generated may not match PANTONFE identified standards Consult current PANTONE Publications for accurate color PANTONE and other Pantone In
197. inting Shortcuts box select the printing shortcut that you want to use ET NOTE Touse printer driver default settings select Factory Default Resize documents or print on a custom paper size You can scale a document to fit on a different size of paper 1 Onthe File menu click Print 2 Open the Paper Handling menu 3 Inthe area for Destination Paper Size select Scale to fit paper size and then select the size from the drop down list 4 Ifyou want to use only paper that is smaller than the document select Scale down only Print a cover page You can print a separate cover page for your document that includes a message such as Confidential 1 On the File menu in the software program click Print 2 Select the driver and then click Properties or Preferences 3 On the Cover Page or Paper Quality tab select whether to print the cover page Before Document or After Document 4 Inthe Cover Page Type pop up menu select the message that you want to print on the cover page ET NOTE To print a blank cover page select Standard as the Cover Page Type 126 Chapter9 Print tasks ENWW Use watermarks A watermark is a notice such as Confidential that is printed in the background of each page of a document 1 On the File menu click Print 2 Open the Watermarks menu 3 Next to Mode select the type of watermark to use Select Watermark to print a semi transparent message Select Overlay to print a mess
198. intosh Software for Macintosh Computel Snina ninisi i E A AE aiaa iA 70 Remove software from Macintosh operating systems sssssssssee eme 71 5 Software for other operating systems AP Web Jetadtimin erre rere derent ete FR e n RYE Ee RE R RARI d cre ERU le ree Exe EC eek pana deep 74 6 Connectivity Parallel CONMECUON ETE 78 USB COMMCCHON P A 79 XD elt reersnzet one e M 80 Network Configuration M 81 Configure TCP IPVA pararnetets idet een aea edad nee 81 Change the IP address ssssssssssssse eene eene nennen 81 Set the subnet mask pee tea Preetz RE Ee n RR RR CERE RN RR AERE e ea dnd dA 82 Set the default gateway sssssssssseene eene 82 Configure TCP IPv6 parameters ssssseseeeeneeene eene eene nens 83 Disable network protocols optional 83 Disable IPXI SPR nm 83 Disable Apple Talk teet tt eee tet nca d banane ded cx Rus 84 Disable DLO LLO e e RE er edits 84 HP Jetdirect EIO print servers ssssssssssssssssssseeeeneerne en nennen nennen nennen nennen 84 Network utilities 85 HP Web Jetadmilri irte rr nr RET IURE FREE USE THERE TRE PURIS Se AERE S PO ETT EPA ER d 85 Embedded Web server sssssssssssssssssseeeene enne enne ener ness enne nennen 85 HP Easy
199. ion See Solve network printing problems Contact the network administrator Non HP supply installed A refilled color or a cloned color mono cartridge has been installed and the printer previously used all genuine HP supplies It can also appear when an unauthorized cartridge has been installed and the printer previously used all genuine supplies Install a genuine HP cartridge or touch OK to override the condition 234 Chapter 16 Problem solving ENWW Table 16 1 Control panel messages continued Control panel message Description Recommended action Novel login required Novell authentication has been enabled for this destination Enter Novell network credentials to access the requested feature Order color Cartridge The identified print cartridge is nearing the end of its useful life The MFP is ready and will continue for the estimated number of pages indicated Estimated pages remaining is based upon the historical page coverage of this MFP Printing will continue until a supply needs to be replaced Order a replacement print cartridge Order Fuser Kit The fuser is near end of life The MFP is ready and will continue for the estimated number of pages indicated Printing will continue until a supply needs to be replaced Order a replacement fuser kit Order staple cartridge The staple cartridge needs to be replaced 1 Replace the staple cartridge Order Suppl
200. ion in the driver instead of the QuickCopy option In the driver select the QuickCopy option and then type a user name and a job name When you send the job to print the device prints the number of copies that you set in the driver To print more quick copies at the device control panel see Print additional copies of a QuickCopy job Print additional copies of a QuickCopy job This section describes how to print additional copies of a job stored on the device hard disk at the control panel 1 From the Home screen touch Job Storage Touch the Retrieve tab Scroll to and touch the job storage folder that holds the job 2 3 4 Scroll to and touch the job that you want to print 5 Touch the Copies field to change the number of copies to print 6 Touch Retrieve Stored Job amp to print the document Delete a QuickCopy job Delete a QuickCopy job at the device control panel when you no longer need it If the device requires additional space to store new QuickCopy jobs the device automatically deletes other stored QuickCopy jobs starting with the oldest job ET NOTE Stored QuickCopy jobs can be deleted at the control panel or in HP Web Jetadmin 1 From the Home screen touch Job Storage Touch the Retrieve tab Scroll to and touch the job storage folder that holds the job 2 3 4 Scroll to and touch the job that you want to delete 5 Touch Delete 6 Touch Yes 110 Chapter 8 Use product features
201. ipurpose tray A multipurpose tray for paper transparencies labels and envelopes Holds up to 100 sheets of paper or 20 envelopes e Tray 2 3 and 4 500 sheet trays These trays automatically detect standard paper sizes up to legal and allow printing on custom size paper e Automatic document feeder ADF Holds up to 50 sheets of paper 6 Chapter 1 Product basics ENWW Connectivity Duplex printing and copying Provides two sided printing and copying printing on both sides of the paper ADF duplex scanning The ADF has an automatic duplexer for scanning two sided documents Output Standard output bin The standard output bin is located on the left side of the MFP This bin can hold up to 500 sheets of paper ADF output bin The ADF output bin is underneath the ADF input tray The bin holds up to 50 sheets of paper and the MFP automatically stops when this bin is full Optional stapler stacker standard on the CM4730fm MFP The stapler stacker staples up to a 30 sheet document and stacks up to 500 sheets Optional 3 bin mailbox standard on the CM4730fsk MFP One bin stacks up to 500 sheets and two bins stack up to 100 sheets each for a total capacity of 700 sheets IEEE 1284C compliant parallel connection A Foreign Interface Harness FIH connection AUX for connecting other devices Local area network LAN connector RJ 45 for the embedded HP Jetdirect print server Optional analog fax card standard on the CM4
202. is 15 seconds a print job gets interrupted this setting indicates how long the device will wait before it reports that the job has failed Parallel Input High Speed No Use the High Speed setting to configure the speed that the parallel port uses to communicate with the host EP NOTE This Yes default zs ROLES Advanced Functions Enabled default Use the Advanced Functions setting to enable or omy ea disable bidirectional parallel communication accessory IS Disabled installed Embedded Jetdirect See Table 2 11 Jetdirect menus for the list of options EIO X Jetdirect Table 2 11 Jetdirect menus Menu item Sub menu item Sub menu item Values and Description TCP IP Enable Off Disable the TCP IP protocol On default Enable the TCP IP protocol Host Name An alphanumeric string up to 32 characters used to identify the device This name is listed on the HP Jetdirect configuration page The default host name is NPbooxxx where xxxxxx is the last six digits of the LAN hardware MAC address IPV4 Settings Config Method Specifies the method that TCP IPv4 parameters will be configured on the HP Jetdirect print server Initial Setup menu 31 Table 2 11 Jetdirect menus continued Menu item Sub menu item Sub menu item Values and Description Default IP Bootp Use BootP Bootstrap Protocol for automatic configuration from a BootP server DHCP Use DHCP Dynamic Host Configuration Protocol fo
203. izontally vertically or both ways Possible causes The scanner is not calibrated properly Troubleshooting and suggestions Calibrate the scanner 284 Chapter 16 Problem solving ENWW Unexpected image Defect description The copy does not look like the original document Possible causes There is media on the flatbed glass from a previous copy job Troubleshooting and suggestions Remove any media from the flatbed glass Calibrate the MFP The MFP automatically calibrates and cleans at various times to maintain the highest level of print quality The user might also request the MFP to calibrate via the MFP s control panel using Quick Calibration or Full Calibration located in the Print Quality gt Calibration Cleaning menu Quick Calibration is used for D Half color tone calibration If color density or tone seems wrong Quick Calibration can be run Full Calibration includes the Quick Calibrate routines and adds Drum Phase Calibration Color Plane Registration CPR and copy parameter calibration routines If color layers black magenta cyan and yellow on the printed page seem to be shifted from one another Full Calibration should be run The HP Color LaserJet CM4730 MFP incorporates a new feature to skip calibration when appropriate thereby making the MFP available more quickly For example if the MFP is powered off and on quickly within 20 seconds calibration i
204. k Apply e Scroll down to Accessory Output Bin select HP 500 sheet stapler stacker or HP 700 Sheet 3 bin Mailbox and click Apply Configure the printer driver to recognize the 3 bin mailbox in Macintosh 6 Open the Printer Center utility Select HP Color LaserJet CM4730 On the File menu click on Show Info command i Select the Installable Options tab Scroll to Accessory Output Bins and select HP 500 sheet stapler stacker or HP 700 Sheet 3 bin Mailbox Click Apply Changes Select the 3 bin mailbox operating mode at the control panel 1 2 3 4 5 Scroll to and touch Administration Touch Device Behavior Touch MBM 3 Configuration Touch Operation Mode Select the operation mode that you want to use Select the 3 bin mailbox operating mode in the printer driver ENWW 1 Click the Start button point to Settings and then click Printers for Windows 2000 or Printers and Faxes for Windows XP Right click the HP product icon and then click Properties or Printing Preferences Click the Device Settings tab Perform one of the following actions For automatic configuration under Installable Options click Update Now in the Automatic Configuration list Or For manual configuration under Installable Options select the appropriate operation mode in the Accessory Output Bin list Click OK to save the settings Select the output bin 103 Select the operating mode in the printer drive
205. k these lal ies dae net dde ge d eats 287 Solve e mail problems maaana eae aaa aei aeai ea anaa aeai r ane a ae naaa snis ln sinn d nnn ne nnns sessilia 288 Validate the SMTP gateway address ssssssssee eene 288 Validate the LDAP gateway address ssssssssssseene emen 288 Solve problems with output accessories ssssssssssssssssssseee enemies 289 Solve network connectivity problems sssssesssssseeeeenee eene nnne nennen enne nnne nns 290 Solve network printing problems ssssssssssssssssssemeeenennene nennen 290 Verify communication over the network sssssssssseenne emen 290 Solve common Macintosh problems sss eene nrrnmr nnns nnns 292 xi Appendix A Supplies and accessories Order parts accessories and supplies sssssssssssssssseseeneeneeemermennn nnn 296 Order directly from FIP iet ter tesd tee rada ee eoa RN reae E EE NR R ARR RREAR ERE TY REM 296 Order through service or support providers sssssssssseseseeeeemnee 296 Order directly through the embedded Web server sssss 296 Optional output devices sssssssssssssssssssseeneenene eene enne emen nene n nnns denen nennen nnne senes 297 Output accessory bridge 2 nns eaten EE ERRARE FRA DE ERRARE RE ERR ERA Yeu 297 Sese RR 297 Staplet stacket iiosee nie eene treten re ee Fa esed a e ret Here e ane 298 Pa
206. kit Q7504A Image fuser kit 110 volt Q7502A Image fuser kit 220 volt Q7503A ADF mylar maintenance kit Q4696 67901 ADF maintenance kit Q5997A ENWW Part numbers 299 Customer replaceable units Item Description Part number Cassette pick up roller replacement kit CB480 67902 Control panel replacement kit CB480 67901 Formatter replacement kit CB480 67905 MP pick up roller kit CB480 67903 MP pick up unit replacement kit CB480 67904 Fax assembly replacement kit CB480 67906 Memory Item Description Part number 100 pin DDR memory DIMM dual inline 128 MB Q7721AA memory module 256 MB Q7722A Boosts the ability of the MFP to handle large or complex print jobs 512 MB Q7723A Cables and interfaces Item Description Part number Enhanced I O EIO card HP Jetdirect 635n IPv6 IPsec Print J7961G Server Parallel cable 2 meter IEEE 1284 C cable C2950A 3 meter IEEE 1284 C cable C2951A USB cable 2 meter standard USB compatible C6518A device connector 300 Appendix A Supplies and accessories ENWW B Service and support Hewlett Packard limited warranty statement HP PRODUCT DURATION OF LIMITED WARRANTY HP LaserJet CM4730 Series MFP One year limited warranty HP warrants to you the end user customer that HP hardware and accessories will be free from defects in materials and workmanship after the date of purchase for the period specified above If HP receives notice of such defec
207. l duplex printing sssssssseeenneem 131 Set the stapling optlOris eiie nhe nar er RII Ee ERE E ECERET UE RSEN NERA RENI BARS IR EE Ee Ea 131 Select the stapler in the printer driver ssssss 131 Configure the printer driver to recognize the optional stapler stacker 131 Set the color options ssssssssssssssssssseeee eene en eren etes nne n nennen nns 132 Use the Services MENU i iere eiii eee ie Eto cr EGRE ERERTRE Nuno RETE cognate Ie Fe ERR D ERE RESET Eee ERA 132 IiCcle Hefee M TDI LLL T 0 0 TD 133 Set the stapler at the control panel for printed jobs ssssssssessss 133 Set the stapler at the control panel for all copy jobs sssssssseee 133 Set the stapler at the control panel for a single copy job sseeese 134 Configure the device to stop or continue when the staple cartridge is empty 134 Load staples ee nii RRR IA a I SERE R REN u A asd NOM OR die ce Re Er EAR aaia 134 Cancela Print JOD e 136 Stop the current print job from the control panel cecceccceeeeceeceeeeeeeeeeeeeeeeeeenenneaeeees 136 Stop the current print job from the software program sssssssssss 136 10 Using color HP ImageREt 3000 art ne aaia pet tarde dedu xut edad etus V d xad s und 138 Restrict COIOP USC mU 139 Restrict color pining En TM 139 Restri
208. l panel you can scan black and white or color documents and send them to an e mail address as an e mail attachment To use digital sending the device must be connected to a local area network LAN ET NOTE The e mail icon is not shown on the control panel if e mail is not configured This chapter addresses the following topics e Configure e mail settings e Use the Send E mail screen e Perform basic e mail functions e Use the address book e Change e mail settings for the current job e Scanto a folder e Scan to a workflow destination 165 Configure e mail settings Before you can send a document to e mail you must configure the device ET NOTE The instructions that follow are for configuring the device at the control panel You can also perform these procedures by using the embedded Web server For more information see Embedded Web server Supported protocols The HP LaserJet CM4730 MFP models support Simple Mail Transfer Protocol SMTP and Lightweight Directory Access Protocol LDAP SMTP LDAP SMTP is a set of rules that define the interaction between programs that send and receive e mail In order for the device to send documents to e mail it must be connected to a LAN that has access to an e mail server that supports SMTP The SMTP server must also have Internet access If you are using a LAN connection contact your system administrator to obtain the IP address or hos
209. lect the paper size that is most often used for copy or scan originals Number of Sides 1 Select whether copy or scan originals are most often single sided or double sided 2 Orientation Portrait Select the orientation that is most often used for copy or scan originals Select Portrait if the short edge is at the top or select Landscape Landscape if the long edge is at the top Optimize Text Picture Manually Adjust Optimize the output for a particular type of original text pictures or a mixture of both Text If you select Manually Adjust specify the mix of text and pictures that Printed Picture is used most often Photograph 20 Chapter2 Control panel ENWW Image adjustment Administration gt Default Job Options gt Image Adjustment Table 2 3 Image Adjustment menu Menu item Values Description Darkness Select a value Select the level of density darkness for the output Background Cleanup Adjust the value within the range Increase the Background Removal setting to remove faint images from the background or to remove a light background color Sharpness Adjust the value within the range Adjust the Sharpness setting to clarify or soften the image ENWW Default Job Options menu 21 Default Copy Options Administration gt Default Job Options gt Default Copy Options Table 2 4 Default Copy Options menu Menu item Sub menu item Values Description Number of Copies Type the number of Set the default number of
210. lect the stapler in the printer driver sssssssmRee 123 Configure the printer driver to recognize the optional stapler stacker 124 Setting the color options 2 0 0 ner eee eee eee nese errr eee nennen nennen a 124 Use the Services tab ir ee reete rte ged nde FIR aad uacavinadedinenade igs due ada naian 125 Using the HP Digital Imaging Options dialog box sem 125 Macintosh printer driver features c cccccccccceceeeeeeeeeeeeeceeeecaaeaaaeaaeceeeeeeeeeeeeeeeseceescaaaaaeaaeeaeeeeeeeeeees 126 Create and use printing shortcuts in Macintosh sse 126 Resize documents or print on a custom paper size ssssssssR 126 xislMe Eeo figere 126 Use Watermlarks scettr e eee anisar e CR aia CIERRE EEBA UN ER RNRxY d X PM M once S enia sg duque 127 Print multiple pages on one sheet of paper in Macintosh ccccceeeeeeeeeeeeeeeeeeeeeeeeeees 127 Print on both sides of the page duplex printing sn 127 Automatic duplex printing cei ttti Ea hann tete kenne eq unn a eee n na a 127 Enable or disable automatic two sided printing from the control ecu 129 Enable or disable automatic two sided printing in the Macintosh printer dTIVET m H aS 130 Layout options for printing on both sides 130 vi ENWW Options for binding two sided printing jobs sees 131 Manua
211. lex printing binding options 121 131 control panel settings 120 129 manual 122 131 duplex printing accessory error messages 232 233 locating 9 specifications physical 311 duplex printing accessory loading 120 130 duplexing copying documents 158 duty cycle 5 E e mail about 165 169 address books 171 configuring 166 embedded Web server settings 186 error messages 233 234 237 238 LDAP errors 234 sending documents 169 troubleshooting 224 validating gateway addresses 288 E mail Setup menu 42 economy settings 106 EIO accessory settings 31 EIO card part number 300 EIO cards buffer overflow 229 errors 232 installing 340 electrical specifications 313 embedded Web server assigning a password 196 checking toner level 208 Digital Sending tab 186 features 184 Information tab 185 Networking tab 186 opening 184 Other Links tab 187 Settings tab 185 energy specifications 313 Enhanced I O card part number 300 enlarging documents 117 envelope feeder specifications physical 311 envelopes jams 258 loading in tray 1 93 environment specifications 208 315 Environmental Product Stewardship Program 320 EPS files troubleshooting 293 Equitrac devices 196 erasing hard disk 197 Error button control panel touchscreen 16 error messages alphabetical list 226 numerical list 226 types of 225 Ethernet cards 7 European Union waste disposal 322 Explorer versions supported embedded Web server 184 HP Web Jetadmin 190 Ex
212. lose error message 234 specifications physical 311 unexpected size or type error message 229 A access denied message 232 accessories lights 260 ordering 296 partnumbers 299 accounting hardware 196 acoustic specifications 314 activity log fax 183 address book e mail deleting addresses 172 address books e mail adding addresses 171 clearing 54 importing 186 LDAP server errors 234 recipient lists 171 recipient lists creating 171 ENWW address books e mail auto complete function 170 LDAP support 166 address printer Macintosh troubleshooting 292 ADF blank pages 280 capacity 6 cleaning delivery system 213 image shift troubleshooting 284 lines on copies 281 283 maintenance kit 219 sizes supported 169 skewed pages 282 unexpected image troubleshooting 285 ADF input tray locating 9 ADF output bin capacity 7 selecting 101 Administration menu control panel 17 agreements maintenance 309 AppleTalk setting 84 AppleTalk settings 34 Attention light locating 14 authentication error messages 232 autoconfiguration drivers 64 Automatic Configuration feature drivers 65 automatic media sensing 99 automatic two sided printing path copying documents 158 AUX connection 7 auxiliary connection configuration 80 B billing codes report fax 183 bins capacities 7 full error messages 235 locating 9 reattach error message 236 selecting 101 blank pages printing 117 blank pages troubleshooting 280 blocked f
213. lusion may not apply to you THE WARRANTY TERMS CONTAINED IN THIS STATEMENT EXCEPT TO THE EXTENT LAWFULLY PERMITTED DO NOT EXCLUDE RESTRICT OR MODIFY AND ARE IN ADDITION TO THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU 302 Appendix B Service and support ENWW Customer self repair warranty service ENWW HP products are designed with many Customer Self Repair CSR parts to minimize repair time and allow for greater flexibility in performing defective parts replacement If during the diagnosis period HP identifies that the repair can be accomplished by the use of a CSR part HP will ship that part directly to you for replacement There are two categories of CSR parts 1 Parts for which customer self repair is mandatory If you request HP to replace these parts you will be charged for the travel and labor costs of this service 2 Parts for which customer self repair is optional These parts are also designed for Customer Self Repair If however you require that HP replace them for you this may be done at no additional charge under the type of warranty service designated for your product Based on availability and where geography permits CSR parts will be shipped for next business day delivery Same day or four hour delivery may be offered at an additional charge where geography permits If assistance is required you can call the HP Technical Support Center and a technician will help you over the phone HP sp
214. manage the color space e Select None to instruct the printer to print RGB data in raw device mode To render documents properly when this option is selected you must manage color in the program that you are using or in the operating system CAUTION Use this option only if you are familiar with the procedures for managing color in the software program or in the operating system e Select Custom Profile when you want to duplicate the printed output from other printers This setting instructs the printer to use a custom input profile to more accurately predict and control color output You can download custom profiles from http www hp com Edge Control The Edge Control setting determines how edges are rendered Edge control has three components adaptive halftoning Resolution Enhancement Technology REt and trapping Adaptive halftoning ENWW Manage printer color options on Macintosh computers 151 increases the edge sharpness Trapping reduces the effect of incorrect color alignment by slightly overlapping the edges of adjacent objects The color REt option smooths the edges E NOTE Ifyou notice white gaps between objects or if you notice areas that have a slight shadow of cyan magenta or yellow at the edge choose an edge control setting that increases the trapping level Four levels of edge control are available e Maximum is the most aggressive trapping setting Adaptive halftoning and color REt settings are on e N
215. ments for information on configuring and using the optional stapler stacker 298 Appendix A Supplies and accessories ENWW Part numbers Ordering information and availability might change during the life of the MFP Accessories Item Description Part number 3 bin mailbox Provides three output bins that hold a total of 700 sheets It is included with the HP Color LaserJet CM4730fm MFP ER NOTE The 3 bin mailbox comes with an output accessory bridge Q7520A 500 sheet stapler stacker Allows for high volume output with automatic job finishing Staples up to 30 sheets of paper It is included with the HP Color LaserJet CM4730fsk MFP EE NOTE The stapler stacker comes with an output accessory bridge Q7519A 5 000 staple cartridge Provides one staple cartridge C8091A HP LaserJet analog fax accessory 300 Provides fax capability for the MFP This is included with the HP Color LaserJet CM4730f MFP CM4730fsk MFP and CM4730fm MFP models Q3701A Print cartridges Item Description Part number HP LaserJet black print cartridge 12 000 page black cartridge Q6460A HP LaserJet cyan print cartridge 12 000 page cyan cartridge Q6461A HP LaserJet yellow print cartridge 12 000 page yellow cartridge Q6462A HP LaserJet magenta print cartridge 12 000 page magenta cartridge Q6463A Maintenance kits Item Description Part number Image transfer ETB
216. mplexity of a print job from within a software program can help avoid memory problems 206 Chapter 14 Manage the MFP ENWW Manage supplies Use genuine HP print cartridges for the best printing results HP print cartridges When you use a genuine new HP print cartridge you can obtain the following supplies information e Percentage of supplies remaining e Estimated number of pages remaining e Number of pages printed ET NOTE See Supplies and accessories for cartridge ordering information Non HP print cartridges Hewlett Packard Company cannot recommend the use of non HP print cartridges either new or remanufactured Because they are not genuine HP products HP cannot influence their design or control their quality Service or repair required as a result of using a non HP print cartridge will not be covered under the MFP warranty If the non HP print cartridge was sold to you as a genuine HP product see HP fraud hotline Print cartridge authentication The HP Color LaserJet CM4730 MFP series automatically authenticates the print cartridges when the cartridges are inserted into the MFP During authentication the MFP will let you know if a cartridge is a genuine HP print cartridge If the MFP control panel message states that this is not a genuine HP print cartridge and you believe you purchased an HP print cartridge call the HP fraud hotline To override a non HP print cartridge error message touch OK HP fra
217. multipurpose tray make sure that the side guides are set correctly Correct print quality and copy quality problems 279 Blank page Defect description The printed page is blank Possible causes The page was not inserted into the ADF properly The ADF separation pad is not functioning properly Troubleshooting and suggestions 1 Remove and then reinsert the original page into the ADF making sure it is placed face up 2 If several pages are feeding at the same time check the ADF separation pad and rollers for damage If the rollers are dirty clean them If the ADF separation pad or rollers are worn replace them 280 Chapter 16 Problem solving ENWW Horizontal lines Defect description Horizontal lines appear on the page Possible causes The ADF is dirty Paper is stuck to the scanner glass or lid The mylar strip is dirty Troubleshooting and suggestions 1 Clean the ADF 2 Verify that no paper is on top of the scanner glass or stuck to the bottom of the scanner lid 3 Ifthe mylar strip is dirty or worn replace it Replacement mylar strips are stored in an envelope that is underneath the white vinyl ADF backing Follow the instructions that are in the envelope ENWW Correct print quality and copy quality problems 281 Page skew AQBbCc AaBbCc AQBbCc AadBbcc Defect description The printing is skewed on the page Possible causes The ADF tray guides are not adjusted properly
218. n HP Jetdirect print server with another type of network port go to http www hp com support ljcm4730mfp Install the printing system software 59 The installer does not support MFP installation or MFP object creation on Novell servers To install your MFP and create objects on a Novell server use an HP utility such as HP Web Jetadmin or a Novell utility such as NWAdmin You must have administrator privileges to install software in Windows 2000 Windows Server 2003 Windows XP or Windows Vista 1 Before installation print a configuration page see Information pages On the last page locate the MFP IP address You will need this address to complete the network installation Quit all unnecessary software programs Insert the MFP CD into the CD ROM drive If the welcome screen does not open use the following procedure e On the Start menu click Run e Type X setup where X is the letter of the CD ROM drive e Click OK When prompted click Install and follow the onscreen instructions Click Finish when installation has completed You might need to restart the computer Print a test page or a page from any software program to make sure that the software is correctly installed If installation fails reinstall the software If this fails check the installation notes and Readme files on the MFP CD or the flyer that came in the MFP box or go to http www hp com support ljcm4730mfp Use Windows sharing on a network
219. n printing on labels Serious damage can result ET NOTE Changing settings for two sided printing on the MFP control panel affects all print jobs Whenever possible change settings for two sided printing through your software program or printer driver NOTE Anychanges made in the printer driver override settings made on the MFP control panel 1 Scroll to and touch Administration Touch Default Job Options Touch Default Print Options Touch Print Sides Touch 2 sided eo p om o M Touch Save ENWW Macintosh printer driver features 129 Enable or disable automatic two sided printing in the Macintosh printer driver Use automatic duplex printing 1 2 3 4 5 Insert enough paper into one of the trays to accommodate the print job If you are loading special paper such as letterhead load it in one of the following ways e Fortray 1 load the letterhead paper face up with the bottom edge feeding into the printer first e Forall other trays load the letterhead paper face down with the top edge at the back of the tray Open the printer driver see Open the printer drivers Open the Layout pop up menu Next to Two Sided Printing select either Long Edge Binding or Short Edge Binding Click Print Layout options for printing on both sides The following are the four duplex orientation options To select option 1 or 4 select Flip Pages Up in the printer driver o o e
220. nality See the HP LaserJet Analog Fax Accessory 300 User Guide for all regulatory approval information and regulatory notices associated with the fax functionality and that device 326 Appendix D Regulatory information ENWW Laser statement for Finland LASERTURVALLISUUS LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT HP Color LaserJet CM4730 MFP CM4730f MFP CM4730fsk MFP and CM4730fm MFP laserkirjoitin on kayttajan kannalta turvallinen luokan 1 laserlaite Normaalissa kayt6ssa kirjoittimen suojakotelointi est lasers teen p syn laitteen ulkopuolelle Laitteen turvallisuusluokka on m ritetty standardin EN 60825 1 1994 mukaisesti VAROITUS Laitteen k ytt minen muulla kuin k ytt ohjeessa mainitulla tavalla saattaa altistaa k ytt j n turvallisuusluokan 1 ylitt v lle n kym tt m lle lasers teilylle VARNING Om apparaten anv nds p annat s tt n i bruksanvisning specificerats kan anv ndaren uts ttas f r osynlig laserstr lning som verskrider gr nsen f r laserklass 1 HUOLTO HP Color LaserJet CM4730 MFP CM4730f MFP CM4730fsk MFP and CM4730fm MFP kirjoittimen sis ll ei ole k ytt j n huollettavissa olevia kohteita Laitteen saa avata ja huoltaa ainoastaan sen huoltamiseen koulutettu henkil T llaiseksi huoltotoimenpiteeksi ei katsota v riainekasetin vaihtamista paperiradan puhdistusta tai muita k ytt j n k sikirjassa lueteltuja k ytt j n teht v ksi tarkoitettuja yll pitotoimia j
221. nd accessories Locate supplies Supplies are identified by their labeling and their blue plastic handles The following figure illustrates the location of each supply item Figure 15 1 Supply item locations 1 Fuser 2 Print cartridges 3 Transfer unit Supply replacement guidelines To facilitate the replacement of supplies keep the following guidelines in mind when setting up the MFP e A Allow sufficient space above and in the front of the MFP for removing supplies e The MFP should be located on a flat sturdy surface For instructions on installing supplies see the installation guides provided with each supply item or see more information at http www hp com support ljicm4730mfp When you connect select Solve a Problem CAUTION Hewlett Packard recommends the use of genuine HP products in this MFP Use of non HP products may cause problems requiring service that is not covered by the Hewlett Packard extended warranty or service agreements Approximate replacement intervals for supplies The following table lists the estimated replacement intervals for supplies and the control panel messages that prompt when to replace each item Usage conditions and print patterns may cause results to vary 210 Chapter 15 Maintenance ENWW Item Printer message Page count Approximate time period Black cartridges Replace Black Cartridge 12 000 pages 3 months Color cartridges Replace color Cart
222. nd sharpness and you can use the Background Cleanup setting to remove faint images from the background or to remove a light background color Content Orientation Use this feature to specify the way the content of the original page is placed on the page portrait or landscape Output Bin Use this feature to select an output bin for the copies Optimize Text Picture Use this feature to optimize the output for a particular type of content You can optimize the output for text or printed pictures or you can manually adjust the values Pages per Sheet Use this feature to copy multiple pages onto one sheet of paper Original Size Use this feature to describe the page size of the original document Booklet Format Use this feature to copy two or more pages onto one sheet of paper so you can fold the sheets in the center to form a booklet Edge To Edge Use this feature to avoid shadows that can appear along the edges of copies when the original document is printed close to the edges Combine this feature with the Reduce Enlarge feature to ensure that the entire page is printed on the copies Job Build Use this feature to combine several sets of original documents into one copy job Also use this feature to copy an original document that has more pages than the document feeder can accommodate at one time del R A
223. ndatory for products marketed in the United States The device is certified as a Class 1 laser product under the U S Department of Health and Human Services DHHS Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968 Since radiation emitted inside the device is completely confined within protective housings and external covers the laser beam cannot escape during any phase of normal user operation WARNING Using controls making adjustments or performing procedures other than those specified in this user guide may result in exposure to hazardous radiation Canadian DOC regulations Complies with Canadian EMC Class A requirements Conforme la classe A des normes canadiennes de compatibilit lectromagn tiques CEM VCCI statement Japan COREL FRUBRESERESBERAMRAS VCCI OBE CHOC DFAARRHSECY CORES RERR CHAT OC MBE SMROTCEMHVET omms Rm 35x eI SBEDBRENSCEMHVET Power cord statement Japan Nmd ASN BRAKES SLY ASN ERIRE HOR m Cte REESE As EMI statement Korea EMI statement Taiwan BEHA BEPRED Em CES CERERI PEE HTIRE gt npe ARA TE TEMAT gt EHH BERR BET 7 ENWW Safety statements 325 General telecom statement The HP Color LaserJet CM4730f CM4730fsk and CM4730fm models have the HP LaserJet Analog Fax Accessory 300 already installed to provide communication to the public switch telephone network PSTN for fax functio
224. ners Multilingual program information and instructions are included in every new HP LaserJet print cartridge and supplies package You help reduce the toll on the environment further when you return multiple cartridges together rather than separately HP is committed to providing inventive high quality products and services that are environmentally sound from product design and manufacturing to distribution customer use and recycling When you participate in the HP Planet Partners program we ensure your HP LaserJet print cartridges are recycled properly processing them to recover plastics and metals for new products and diverting millions of tons of waste from landfills Since this cartridge is being recycled and used in new materials it will not be returned to you Thank you for being environmentally responsible ET NOTE Use the return label to return original HP LaserJet print cartridges only Please do not use this label for HP inkjet cartridges non HP cartridges refilled or remanufactured cartridges or warranty returns For information about recycling your HP inkjet cartridges please go to http www hp com recycle 320 Appendix D Regulatory information ENWW Return and recycling instructions United States and Puerto Rico The enclosed label in the HP LaserJet toner cartridge box is for the return and recycling of one or more HP LaserJet print cartridges after use Please follow the applicable instructions below Multiple re
225. nfiguration 79 USB port troubleshooting Macintosh 293 Use different paper covers 116 V validating gateway addresses 288 vertical lines 269 vertical lines problem solving 269 voltage specifications 313 voltage troubleshooting 224 Ww wake time setting 27 106 Warning button control panel touchscreen 16 warranty Customer self repair 303 extended 305 309 print cartridge 306 product 301 watermarks 117 127 Web browser requirements embedded Web server 184 Web Jetadmin browsers supported 190 downloading 190 firmware updates 204 Index 351 Web sites customer support 304 downloading software 304 HP Web Jetadmin downloading 190 Linux support 62 Macintosh support 305 Material Safety Data Sheet MSDS 322 ordering supplies 296 304 service agreements 305 universal print driver 64 white areas 276 white areas problem solving 276 Windows driver settings 67 116 drivers supported 62 software components 86 universal print driver 64 Windows 2000 fax 180 Windows driver settings booklets 123 custom size paper 116 workflow sendto 175 352 Index ENWW 2007 Hewlett Packard Development Company L P www hp com
226. ng color usage go to http www hp com go coloraccess Restrict color copying T 2 3 4 5 6 Scroll to and touch Administration Touch Management Touch Restrict Color Use Touch Color copying access Select one of the following options e Enable Color default This setting allows color copying capabilities for all users e Disable Color This setting denies color copying capabilities to all users Touch Save For more information about restricting and reporting color usage go to http www hp com go coloraccess ENWW Restrict color use 139 Paper selection For the best color and image quality it is important to select the appropriate media type from the MFP menu or from the front panel 140 Chapter 10 Using color ENWW Color options ENWW Color options enable optimal color output automatically for diverse types of documents Color options use object tagging which allows optimal color and halftone settings to be used for different objects text graphics and photos on a page The printer driver determines which objects are used on a page and uses halftone and color settings that provide the best print quality for each object Object tagging combined with optimized default settings produces great color out of the box In the Windows environment the Automatic and Manual color options are on the Color tab in the printer driver For more information see Select the correct printer driver Col
227. nks to the HP Web site for registration support and for ordering supplies 188 Chapter 14 Manage the MFP ENWW ENWW Section Description NOTE f you use a dial up connection and did not connect to the Internet when you first opened the HP Easy Printer Care software you must connect before you can visit these Web sites E Supplies Ordering window Provides access to online or e mail supplies ordering Ordering list Shows the supplies that you can order for each printer If you want to order a certain item click the Order check box for that item in the supplies list Shop Online for Supplies button Opens the HP supplies Web site in a new browser window If you have checked the Order check box for any items the information about those items can be transferred to the Web site Print Shopping List button Prints the information for the supplies that have the Order check box selected Email Shopping List button Creates a text list of items that have the Order check box selected The list can be copied into an e mail message that you send to your supplier Alert Settings window Allows you to configure the printer to automatically notify you of printer issues Alerts on or off Activates or deactivates the alerts feature for a certain printer When alerts appear Sets when you want alerts to appear either when you are printing to that particular printer or anytime there is a printer event
228. not feed in the MFP Envelopes jam or will not feed in the MFP Cause Solution Envelopes are loaded in an unsupported tray Only tray 1 can Load envelopes into tray 1 feed envelopes Envelopes are curled or damaged Try using different envelopes Store envelopes in a controlled environment Envelopes are sealing because the moisture content is too Try using different envelopes Store envelopes in a controlled high environment Envelope orientation is incorrect Verify that the envelope is loaded correctly This MFP does not support the envelopes being used Refer to the HP LaserJet Printer Family Print Media Guide Tray 1 is configured for a size other than envelopes Configure tray 1 size for envelopes 258 Chapter 16 Problem solving ENWW Output is curled or wrinkled Output is curled or wrinkled Cause Media does not meet the specifications for this MFP Solution Use only media that meets the HP media specifications for this MFP Media is damaged or in poor condition Remove media from the input tray and load media that is in good condition Printer is operating in an excessively humid environment Verify that the printing environment is within humidity specifications You are printing large solid filled areas Media used was not stored correctly and might have absorbed moisture Large solid filled areas can cause excessive curl Try using a different pattern Rem
229. not meet HP specifications Trays are not configured properly or settings are not correct for media in use There are undetected jams Troubleshooting and suggestions 1 Make sure that the environmental specifications for the device are being met 2 Make sure that type and quality of the media you are using meet HP specifications 3 Make sure that the media type and size for the tray are set correctly in the control panel for the media that you are using 4 Calibrate the MFP 5 Print the Print Quality Troubleshooting Pages and follow the diagnostic procedure listed on the first page to help isolate the defect to a particular component 278 Chapter 16 Problem solving ENWW Skewed stretched or off center page ENWW Defect description The image is skewed stretched or off center on the page Possible causes Operating environment or media in use does not meet HP specifications Media is not loaded correctly Troubleshooting and suggestions m oo m ow m Make sure that the environmental specifications for the device are being met Make sure that type and quality of the media you are using meet HP specifications Make sure that the media is loaded correctly For problems with page skew turn over the stack of media and rotate the stack 180 degrees Make sure that the fuser and transfer belt are seated correctly Inspect the jam areas and remove any undetected jammed or torn media If printing from the
230. nting are enabled the MFP will automatically print on two sides if the duplexer supports the selected size and type Otherwise manual duplex will be enabled For best results avoid using rough textured heavyweight media when duplexing When using special media such as letterhead or forms place the media face down in tray 2 3 or 4 with the logo to the left Place special media face down in tray 1 with the logo feeding into the MFP ast Windows printer driver features 119 Enable or disa ble automatic two sided printing from the control panel If you cannot adjust two sided printing settings in your software program or printer driver adjust them on th A ET 1 2 3 4 5 6 e control panel The factory default setting is 1 sided CAUTION Do not use two sided printing when printing on labels Serious damage can result NOTE Changing settings for two sided printing on the MFP control panel affects all print jobs Whenever possible change settings for two sided printing through your software program or printer driver NOTE Anychanges made in the printer driver override settings made on the MFP control panel Scroll to and touch Administration Touch Default Job Options Touch Default Print Options Touch Print Sides Touch 2 sided Touch Save Enable or disable automatic two sided printing in the printer driver A ET 120 Chapter 9 CAUTION Do not use two sided printing when prin
231. nting shortcuts in Windows sss ete aeeeeeereeeea 116 Set a customi paper SIZe oer reete e aa e ena E ur Yee Lap eerh se Me dee su Fan ag ders 116 Use different paper and print covers ssssssssssssssesseeenen mener 116 Printa blank first page 1 diede R EE IIo ERR elated eesti 117 Use Watermarks rene rone en en ea tte eR ERR ek eee Re CUP Eae ERE ean E x IER RER Onde e E ERE e de 117 Resize documents e nei ERR IRE EE ER ENTER RAN SR aaa EET RO aaa Ke Ha E Re det eds 117 Print multiple pages on one sheet of paper in Windows sse 118 Print on both sides of the page duplex printing ses 119 Automatic two sided duplex printing se 119 Enable or disable automatic two sided printing from the control enlm pL 120 Enable or disable automatic two sided printing in the printer nuls ELE 120 Enable or disable automatic two sided printing in the Windows printer driver seeeeeeeeseseseesessssesss 121 Layout options for printing on both sides 121 Options for binding two sided printing jobs ssssssssssse 121 Printing booklets aissis irinin aaan 122 Manual two sided duplex printing se 122 Layout options for printing on both sides ssssn 122 Create booklets cc E L 123 Set the stapling options ttt det ane codice tex a aaa a 123 Se
232. nto one of the trays to accommodate the print job If you are loading special paper such as letterhead load it in one of the following ways e Fortray 1 load the letterhead paper face up with the bottom edge feeding into the printer first e Forall other trays load the letterhead paper face down with the top edge at the back of the tray A CAUTION To avoid jams do not load paper that is heavier than 105 g m 28 Ib bond 2 Open the printer driver see Open the printer drivers 3 OntheFinishing pop up menu select the Manual Duplex option E NOTE Ifthe Manual Duplex option is not enabled select Manually Print on 2nd Side 4 Click Print Follow the instructions in the pop up window that appears on the computer screen before replacing the output stack in tray 1 for printing the second half 5 Go to the printer and remove any blank paper that is in tray 1 6 Insert the printed stack face up with the bottom edge feeding into the printer first in tray 1 You must print the second side from tray 1 7 f prompted press the appropriate control panel button to continue Set the stapling options Select the stapler in the printer driver 1 Open a document and then click Print on the File menu 2 Select the appropriate stapling option 3 Inthe Presets pop up menu click Save As and then type a name for the preset Configure the printer driver to recognize the optional stapler stacker 1 Open the Printer Cent
233. nual click Settings to open the Color Settings dialog box Adjust the individual settings for text graphics and photographs You can also adjust the general printing settings Click OK 6 Inthe Color Themes area select the RGB Color option that you want to use 7 Click OK 124 Chapter9 Print tasks ENWW Use the Services tab If the product is connected to a network use the Services tab to obtain product and supply status information Click the Device and Supplies status icon to open the Device Status page of the HP Embedded Web Server This page shows the current status of the product the percentage of life remaining for each supply and information for ordering supplies For more information see Embedded Web server In the Internet Services area select an option from the list to go to various support Web sites for this device Click Go Using the HP Digital Imaging Options dialog box Use HP Digital Imaging Options to print better quality photos and images ET NOTE HP Digital Imaging Options are available for Windows 2000 Windows XP Windows Server 2003 and Vista The following options are available on the HP Digital Imaging Options dialog box e Contrast Enhancement Enhance colors and contrast for washed out photos Click Automatic to allow the printer software to brighten areas of photos that need adjustment e Digital Flash Adjust the exposure in dark areas of photos to bring out detail Click Automatic to
234. of the SMTP server See Solve e mail problems The e mail gateway could not accept the job because the attachment is too large Reduce the size of the e mail attachment by setting the maximum attachment size Set the maximum attachment size on the Digital Sending tab of the embedded Web server See Embedded Web server Try using a different file format or sending the document a few pages at a time A network connection is required for digital sending 224 Chapter 16 Problem solving The MFP cannot find a network connection The administrator should check to see if the MFP is connected to the network See Solve network connectivity problems ENWW Control panel message types Four types of control panel messages can indicate the status of or problems with the device ENWW Message type Description Status messages Status messages reflect the current state of the device They inform you of normal device operation and require no interaction to clear them They change as the state of the device changes Whenever the device is ready not busy and has no pending warning messages the status message Ready appears if the device is online Warning messages Error messages Warning messages inform you of data and print errors These messages typically alternate with the Ready or status messages and remain until you touch OK Some warning messages are clearable If Clearable Warnings is set to Job on the
235. olor default Color If Allowed Disable Color Color copying access This item allows the administrator to disable or restrict color copying Enable Color default Disable Color Color Black Mix Auto default This item controls how the engine switches from color mode to monochrome mode for maximum Mostly color pages performance and print cartridge life ENWW Management menu 29 Table 2 9 Management menu continued Menu item Sub menu item Values Description Mostly black pages Choose Auto to reset the MFP to the factory default setting Choose Mostly color pages if nearly all of your print jobs are color with high page coverage Choose Mostly black pages if you print mostly monochrome jobs or a combination of color and monochrome jobs 30 Chapter2 Control panel ENWW Initial Setup menu Administration gt Initial Setup The Initial Setup menu contains the sub menus shown e Networking and I O menu e Fax Setup menu e E mail Setup menu EZ NOTE Values shown with default are the factory default values Some menu items have no default Networking and I O Administration gt Initial Setup gt Networking and I O Table 2 10 Networking and I O Menu item Sub menu item Values Description I O Timeout Select a value in the I O timeout refers to the elapsed time before a print job range The factory default fails If the stream of data that the device receives for setting
236. on problems on an HP postscript level 3 emulation device It sends a predefined PS file to the device However the test is paperless the file will not print Select Yes to choose this test or No to not choose it Select All Tests Use this item to select all available embedded tests Select Yesto choose all tests Select No to select individual tests Execution Time H Use this item to specify the length of time in hours that an embedded test will be run You can select a value from 1 to 60 hours If you select zero 0 the test runs indefinitely until an error occurs or device is turned off Data gathered from the HTTP SNMP and Data Path tests is printed after the tests have completed Execute No Do not initiate the selected tests Yes Initiate the selected tests ENWW Initial Setup menu 35 Table 2 11 Jetdirect menus continued Menu item Sub menu item Sub menu item Values and Description Ping Test Dest Type This test is used to check network communications This test sends link level packets to a remote network host then waits for an appropriate response To run a ping test set the following items Specify whether the target device is an IPv4 or IPv6 node Dest IP4 IPV4 Type the IPv4 address Dest IP6 IPV6 Type the IPv6 address Packet Size Specify the size of each packet in bytes to be sent to the remote host The minimum is 64 default and the m
237. on of Conformity 319 Environmental product stewardship program Protecting the environment Hewlett Packard Company is committed to providing quality products in an environmentally sound manner This product has been designed with several attributes to minimize impacts on our environment Ozone production This product generates no appreciable ozone gas O3 Power consumption Power usage drops significantly while in Ready Sleep mode which saves natural resources and saves money without affecting the high performance of this product To determine the ENERGY STARG qualification status for this product see the Product Data Sheet or Specifications Sheet Qualified products are also listed at http www hp com hpinfo globalcitizenship environment productdesign ecolabels html Toner consumption Economode uses significantly less toner which might extend the life of the print cartridge Paper use This product s manual optional automatic duplex feature two sided printing and N up printing multiple pages printed on one page capability can reduce paper usage and the resulting demands on natural resources Plastics Plastic parts over 25 grams are marked according to international standards that enhance the ability to identify plastics for recycling purposes at the end of the product s life HP LaserJet print supplies It s easy to return and recycle your empty HP LaserJet print cartridges free of charge with HP Planet Part
238. onents of the control panel are functioning correctly Display Buttons Touchscreen ENWW Troubleshooting menu 53 Resets menu Administration Resets Table 2 18 Resets menu Menu item Values Description Clear Local Address Book Clear Use this feature to clear all addresses from the address books that are stored on the device Clear Fax Activity Log Yes Use this feature to clear all events from the Fax Activity Log No default Restore Factory Telecom Setting Restore Use this option to restore the following settings to their factory default settings Transmit Signal Loss V34 Maximum Baud Rate Speaker Mode Restore Factory Settings Restore Use this feature to restore all device settings to their factory defaults Clear Document Feeder Clear Use this feature to clear the Order Document Feeder Kit and Replace Message Document Feeder Kit warning messages Reset Supplies New Document Feeder Kit Yes Notify the device that a new document feeder kit has been No installed 54 Chapter2 Control panel ENWW Service menu Administration Service The Service menu is locked and requires a PIN for access This menu is intended for use by authorized service personnel ENWW Service menu 55 56 Chapter2 Control panel ENWW 3 Software for Windows e Supported Windows versions e Install the printing system software e Supported printer drivers e Remove software for Windows e Selectthe
239. ons physical 311 stapling 133 too many pages error message 237 stapling 133 Start button 14 Start button control panel touchscreen 16 status Home screen control panel 15 Information tab embedded Web server 185 lights 260 Macintosh services tab 132 messages types of 225 Status button 14 Stop button 14 Stop button control panel touchscreen 16 stopping a print request 136 storage cabinet models including 3 specifications physical 311 storage job accessing 107 features 107 personal 109 proof and hold 108 QuickCopy 110 settings 29 stored 111 stored jobs 111 subnet mask 82 supplies locating 210 management menu 29 ENWW memory errors 226 ordering 296 304 partnumbers 299 recycling 320 replacement intervals 210 replacing 210 Resets menu 54 status page printing 182 status viewing with embedded Web server 185 supply status Services tab Macintosh 132 support embedded Web server links 187 HP Instant Support Professional Edition ISPE 304 Macintosh 305 maintenance agreements 309 online 304 service dealers 305 telephone 304 supported media 89 system requirements embedded Web server 184 HP Web Jetadmin 190 T Taiwan EMI statement 325 TCP IP settings 31 technical support embedded Web server links 187 HP Instant Support Professional Edition ISPE 304 Macintosh 305 maintenance agreements 309 online 304 service dealers 305 telephone 304 telephone numbers ordering supplies 304 service agreements 305
240. opies EET Color Black g 1 to 2 sided Black C Auto 120 More Uncollated C Options o Paper Selection PS Image Adjustment 2 Auto Letter e Normal Figure 11 1 Copy screen 154 Chapter 11 Copy ENWW Set the default copy options You can use the administration menu to establish default settings that apply to all copy jobs If necessary you can override most settings for an individual job After that job is complete the device returns to the default settings 1 From the Home screen scroll to and touch Administration 2 Touch Default Job Options and then touch Default Copy Options 3 Several options are available You can configure defaults for all options or for only some options For information about each option see Adjust the copy settings The built in Help system also provides an explanation of each option Touch the Help button in the upper right corner of the Screen 4 To exit the administration menu touch the Home button in the upper left corner of the screen ENWW Set the default copy options 155 Basic copy instructions This section provides the basic instructions for copying Copy from the scanner glass Use the scanner glass to make as many as 999 copies of small lightweight media less than 60 g m or 16 Ib or heavy media more than 105 g m or 28 Ib This includes media such as receipts newspaper clippings photographs old documents worn documents and books Plac
241. or menu e Print Quality menu e Troubleshooting menu e Resets menu e Service menu ENWW 13 Use the control panel The control panel has a VGA touchscreen that provides access to all device functions Use the buttons and numeric keypad to control jobs and the device status The LEDs indicate overall device status Control panel layout The control panel includes a touchscreen graphical display job control buttons a numeric keypad and three light emitting diode LED status lights C3 c9 Cj OOOO OOOO ooo o S Attention light The Attention light indicates that the device has a condition that requires intervention Examples include an empty paper tray or an error message on the touchscreen Data light The Data light indicates that the device is receiving data Ready light The Ready light indicates that the device is ready to begin processing any job Brightness adjustment dial Turn the dial to control the brightness of the touchscreen Touchscreen graphical display Use the touchscreen to open and set up all device functions Numeric keypad Allows you to type numeric values for number of copies required and other numeric values Sleep button If the device is inactive for a long period of time it automatically enters a sleep mode To place the device into sleep mode or to reactivate the device press the Sleep button Reset button Rese
242. or options 141 SRGB Standard red green blue SRGB is a worldwide color standard originally developed by HP and Microsoft as a common color language for monitors input devices scanners digital cameras and output devices MFPs printers plotters It is the default color space used for HP products Microsoft operating systems the Web and most office software sold today sRGB is representative of the typical Windows computer monitor today and the convergence standard for high definition television ET NOTE Factors such as the type of monitor you use and the room s lighting can affect the appearance of colors on your screen For more information see Color matching The latest versions of Adobe PhotoShop CorelDRAW Microsoft Office and many other software programs use sRGB to communicate color Most importantly as the default color space in Microsoft operating systems sRGB has gained broad adoption as a means to exchange color information between software programs and devices using a common definition that assures typical users will experience greatly improved color matching SRGB improves your ability to match colors between the MFP the computer monitor and other input devices scanner digital camera automatically without the need to become a color expert 142 Chapter 10 Using color ENWW Print in four colors CMYK Cyan magenta yellow and black CMYK are the inks used by a printing press The process is often called fo
243. ormal is the default trapping setting Trapping is at a medium level Adaptive halftoning and color REt settings are on e Light sets trapping at a minimal level Adaptive halftoning and color REt settings are on e Off turns off trapping adaptive halftoning and color REt 152 Chapter 10 Using color ENWW 11 Copy This device can function as a standalone walk up copier It is not necessary to install the printing system software on the computer you can adjust the copy settings at the control panel You can also copy originals by using either the document feeder or the scanner glass This chapter provides information about how to make copies and how to change copy settings including the following topics e Use the Copy screen e Setthe default copy options e Basic copy instructions e Adjust the copy settings e Copy two sided documents e Copy mixed size originals e Change the copy collation setting e Copy photos and books e Combine copy jobs by using Job Build e Cancel a copy job It is recommended that you review the basic control panel information before using the device copying functions See Use the control panel for more information ENWW 153 Use the Copy screen From the Home screen touch Copy to view the Copy screen Note that only the first six copy features are immediately visible In order to view additional copy features touch More Options Start Copy Ready Black c
244. ortal inno S teeihiqu M 196 Disable the FIH portal sssssssssssssssssseeeeeereeernn nnne 197 Secure DISK Er dse tei er DE aet o t nte ta edito tete aetate ebededudt als 197 Data affected d eee MER ERE REM 198 Gain access to Secure Disk Erase ssssssssseseeeeeeneene 198 Additional Information osean nene a a e a a aE a 198 DSS authentication isn ee i ei e denial dale ee tegere bet line 198 Lock the control panel menus sss nennen nere retener sts 198 Set the real time clock iie ete t energie pce Pea Eae e ct ea pene eode Lee dn 199 set the date format neret o n ere i P eee ens 199 Setthe datec vs cos oup an n brennen A itis di eie Sa tana 199 Setthe time format i rite td ee Mt eet b tatit ed teh eerta 199 oSLCthe timez c eene REA RAD cede 199 Configure alerts s nun hai detis un nee ei eed aati 201 Upgrade the Imm ware i iet RE Rcx ie HERE ERR ERE DE cand DO RR ce TRO CR HORDE BEER 202 Determine the current firmware version sss e mener 202 Download new firmware from the HP Web site ssssssss 202 Transfer the new firmware to the MFP ccecceceeeeeeeeeeeeeeeeeeeeeeeeeeeeeaeaeaaaeaaeeaeeaaeeaaees 202 Use FTP to upload the firmware through a browser esseeeeees 202 Use FTP to upgrade the firmware on a network connection 203 Use HP Web Jetadmin to upgrade the firmware
245. otka voidaan suorittaa ilman erikoisty kaluja VARO Mik li kirjoittimen suojakotelo avataan olet alttiina n kym tt m lle lasers teilylle laitteen ollessa toiminnassa l katso s teeseen VARNING Om laserprinterns skyddsh lje ppnas d apparaten r i funktion uts ttas anv ndaren f r osynlig laserstr lning Betrakta ej str len Tiedot laitteessa k ytett v n laserdiodin s teilyominaisuuksista Aallonpituus 785 800 nm Teho 5 mW Luokan 3B laser ENWW Safety statements 327 328 Appendix D Regulatory information ENWW E ENWW Install memory and print server cards The MFP has two 200 pin DDR SDRAM slots One slot is filled a 128 or 256 MB DDR memory module can be inserted in the open slot The MFP also has three flash memory card slots for MFP firmware fonts and other solutions e The first flash memory card is reserved for MFP firmware The slot is marked Firmware Slot e The two additional flash memory card slots are for font cards or third party solutions such as signatures and personalities The slots are marked Slot 2 and Slot 3 AN CAUTION Do not insert a flash memory card that is designed for use with a digital camera The MFP does not support photo printing directly from a flash memory card If you install a camera type flash memory card the control panel displays a message asking if you want to reformat the flash memory card If you choose to reformat the card all data on the card
246. ou For the telephone number for your country region see the flyer that came in the box with the product or visit http www hp com support Before calling HP have the following information ready the product name and serial number the date of purchase and a description of the problem You can also find support on the Internet at http www hp com Click the support amp drivers block Software utilities drivers and electronic information Go to http www hp com go cljcm4730mfp software The site is in English but printer drivers can be downloaded in several languages For information over the telephone see the flyer that came in the box with the MFP Fax accessory support Go to http www hp com go mfpfaxaccessory300 HP direct ordering for accessories or supplies Order supplies from the following Web sites United States http www hp com sbso product supplies Canada http www hp ca catalog supplies Europe http www hp com go supplies Asia Pacific http www hp com paper Order accessories from http www hp com support ljicm4 7 30mfp To order supplies or accessories over the telephone call the following numbers United States businesses 800 282 6672 United States small and medium businesses 800 888 9909 United States home and home offices 800 752 0900 Canada 800 387 3154 304 Appendix B Service and support ENWW ENWW To find the phone numbers for other countries regions see the flyer
247. ouching the paper Printer pulls from incorrect tray Printer pulls from incorrect tray Cause Solution You are using a driver for a different printer For more information Use a driver for this printer The specified tray is empty Load media in the specified tray 256 Chapter 16 Problem solving ENWW Printer pulls from incorrect tray Cause Solution Tray behavior for the requested tray is set to First in the Tray Behavior sub menu of the Device Behavior menu Change the setting to Exclusively The media size is not configured correctly for the input tray Print a configuration page or use the control panel to determine the media size for which the tray is configured The guides in the tray are not against the paper Verify that the guides are touching the paper Media does not feed automatically Media does not feed automatically Cause Solution Manual feed is selected in the software program Load tray 1 with media or if the media is loaded touch OK The correct size media is not loaded Load the correct size media The input tray is empty Load media into the input tray Media from a previous jam has not been completely removed Open the MFP and remove any media in the paper path Closely inspect the fuser area for jams The media size is not configured correctly for the input tray Print a configuration page or use the
248. ove media and replace it with media from a fresh unopened package Media has poorly cut edges Remove media flex it rotate it 180 degrees or turn it over and then reload it into the input tray Do not fan media If the problem persists replace the media The specific media type was not configured for the tray or selected in the software Configure the software for the media see the software documentation Configure the tray for the media see Load paper and print media Printer will not duplex or duplexes incorrectly ENWW Printer will not duplex or duplexes incorrectly Cause Solution You are trying to duplex on unsupported media Verify that the media is supported for duplex printing The printer driver is not set up for duplex printing Set up the printer driver to enable duplex printing The first page is printing on the back of preprinted forms or letterhead Load preprinted forms and letterhead in tray 1 with the letterhead or printed side up and the bottom of the page feeding into the MFP For tray 2 3 and 4 load these media printed side down with the top of the page toward the back of the MFP Media handling problems 259 Understand accessory lights for the 3 bin mailbox and stapler stacker Light Explanation and solution Solid green The accessory is receiving power and is ready The stapler is low on staples Stapler Low On Staples appears on the con
249. ows you to adjust the neutral gray color treatment halftones and edge enhancements for text graphics and photographs To access the Manual color options from the Color tab select Manual and then select Settings Manual color options You can manually adjust color options for Edge Control Halftones and Neutral Grays Edge Control The Edge Control setting determines how edges are rendered Edge control has three components adaptive halftoning REt and trapping Adaptive halftoning increases the edge sharpness Trapping reduces the effect of incorrect color alignment by slightly overlapping the edges of adjacent objects The color REt option smoothes the edges E NOTE Ifyou notice white gaps between objects or if you notice areas that have a slight shadow of cyan magenta or yellow at the edge choose an edge control setting that increases the trapping level Four levels of edge control are available e Maximum is the most aggressive trapping setting Adaptive halftoning and color REt settings are on e Normalis the default trapping setting Trapping is at a medium level Adaptive halftoning and color REt settings are on e Light sets trapping at a minimal level Adaptive halftoning and color REt settings are on e Off turns off trapping adaptive halftoning and color REt 148 Chapter 10 Using color ENWW ENWW Halftone options Halftone options affect the resolution and clarity of your color output You can select
250. p follow the corresponding troubleshooting suggestions If a step resolves the problem you can stop without performing the other steps on the checklist Troubleshooting checklist 1 Make sure the MFP Ready light is on If no lights are on complete these steps a Check the power cable connections b Check that the power switch is on c Check the power source by plugging the MFP directly into the wall or into a different outlet d If none of these measures restores power contact HP Customer Care Check the cabling a Check the cable connection between the MFP and the computer or network port Make sure that the connection is secure b Make sure that the cable itself is not faulty by using a different cable if possible c Check the network connection See Solve network connectivity problems Ensure that the print media that you are using meets specifications Print a configuration page see Information pages If the MFP is connected to a network an HP Jetdirect page also prints a Ifthe pages do not print check that at least one tray contains print media b Ifthe page jams in the MFP see Jams If the configuration page prints check the following items a Ifthe page prints correctly then the MFP hardware is working The problem is with the computer you are using with the printer driver or with the program b Ifthe page does not print correctly the problem is with the MFP hardware Contact HP Customer
251. per jam recovery is disabled the pages involved in a jam will not be reprinted Disable paper jam recovery 1 Scroll to and touch Administration Touch Device Behavior Touch Warning Error Behavior 2 3 4 Touch Jam Recovery 5 Touch Off 6 Touch Save 240 Chapter 16 Problem solving ENWW Clear jams behind the right covers 1 Using the handles open the covers on the right side of the printer 2 ENWW Jams 241 3 If media is present in the lower area grasp the media by both corners and pull up v Dec A py Py VN y EZ NOTE If no media is present at these locations continue to the next step 4 Grasp the green handle on the transfer unit and pull down to open it 5 If media is present in the upper area grasp the media by both corners and pull down 242 Chapter 16 Problem solving ENWW 6 If media is present in the lower area grasp the media by both corners and pull up T 8 ENWW Jams 243 9 Lift the green handle on the duplexer cover to open it 11 Close the transfer unit 244 Chapter 16 Problem solving ENWW 12 Close the covers on the right side of the printer 13 14 Close the drawer 15 If the jam still has not cleared open the lower access door and
252. pose tray instead PS Defer Media Enabled default Disabled Select either the PostScript PS or HP paper handling model Use Another Tray Enabled default Disabled Turn on or off the control panel prompt to select another tray when the specified tray is empty Size Type Prompt Display default default Do not display Control whether the tray configuration message appears whenever a tray is opened or closed Duplex Blank Pages Auto default Yes Control how the device handles two sided jobs duplexing Image Rotation Standard default Alternate Image rotation allows users to put paper in the input tray using the same orientation regardless of whether there is a finisher installed Select Standard to match the loading orientation of other devices that have a finisher Select Alternate to use a different loading orientation that might work better with preprinted forms that are used on legacy products Stapler Stacker Staple None One Staples Out Continue default Stop If the optional stapler stacker is installed use this feature to set stapling characteristics for the device MBM 3 Operation Mode Configuration Function Separator Mailbox Stacker Configure the optional 3 bin mailbox accessory 44 Chapter2 Control panel ENWW Table 2 15 Device Behavior menu continued Menu item Sub menu item Sub menu item Values D
253. printer in the Print Center or Printer Setup Utility Cause Solution The Postscript Printer Description PPD file is corrupt Delete the PPD file from the following hard drive folder Library Printers PPDs Contents Resources lt lang gt lproj where lt lang gt is the two letter language code for the language that you are using Reinstall the software See the getting started guide for instructions The interface cable might be defective or of poor quality Replace the interface cable Make sure to use a high quality cable A print job was not sent to the printer that you wanted Cause Solution The print queue might be stopped Restart the print queue Open print monitor and select Start Jobs The wrong printer name or IP address is being used Another printer with the same or similar name IP address or Rendezvous host name might have received your print job Print a configuration page in order to check the printer name IP address or Rendezvous host name Verify that the name IP address or Rendezvous host name on the configuration page matches the printer name IP address or Rendezvous host name in the Print Center or Printer Setup Utility An encapsulated PostScript EPS file does not print with the correct fonts Cause Solution This problem occurs with some programs e Try downloading the fonts that are contained in the EPS file to the printer before printing e Sendt
254. problem with the network might exist Contact your network administrator for assistance Verify communication over the network If the HP Jetdirect configuration page shows an IP address for the MFP use this procedure to verify that you can communicate with the MFP over the network 1 Windows Click Start click Run and then type cma An MS DOS command prompt opens Or Mac Click Applications click Utilities and then open the Terminal application The terminal window opens Type ping followed by the IP address For example type ping XXX XXX XXX XXXx where XXX XXX XXX XXX is the IPv4 address that is shown on the HP Jetdirect configuration page If the MFP is communicating over the network the response is a list of replies from the MFP 290 Chapter 16 Problem solving ENWW ENWW Verify that the IP address is not a duplicate address on the network by using the address resolution protocol arp a command At the prompt type arp a Find the IP address in the list and compare its physical address to the hardware address that is listed on the HP Jetdirect configuration page in the section called HP Jetdirect Configuration If the addresses match all network communications are valid If you cannot verify that the MFP is communicating over the network contact the network administrator Solve network connectivity problems 291 Solve common Macintosh problems This section lists problems that can occur when using Mac OS X
255. product features HP FastRes and HP Resolution Enhancement technology REt for 1200 x 1200 effective dpi at full engine speed e 256 MB of random access memory RAM expandable to 512 MB by using industry standard 100 pin double data rate dual inline memory modules DDR DIMMs e Memory Enhancement technology MEt that automatically compresses data to use RAM more efficiently User interface e HP Easy Select Control Panel e An embedded Web server to gain access to support and order supplies for network connected products e HP Easy Printer Care software a Web based status and troubleshooting tool e Internet enabled supply ordering capabilities through HP Easy Printer Care software ENWW Product features 5 Languages and fonts HP Printer Command Language PCL 6 HP PCL 5 Printer Management Language XHTML 80 scalable TrueType typefaces HP PostScript 3 emulation PS Copying and sending Modes for text graphics and mixed text and graphics formats Job interrupt feature at copy boundaries Multiple pages per sheet Operator attendance animations for example jam recovery Scan and send to e mail e Local address book for e mail and fax e LDAP addressing Send to folder Automatic duplex two sided scanning Print cartridges 4 Print up to 12 000 pages at 596 coverage No shake cartridge design Authentic HP print cartridge detection Automatic toner strip remover Paper handling Input e Tray 1 mult
256. pty the bin e Stacker mode The 3 bin mailbox can combine the bins to act as a stacker It can stack up to 700 sheets of 75 g m 20 Ib bond paper Jobs are sent to the bottom bin first then to the middle bin and then to the top bin Print jobs that require more than 500 sheets fill the bottom bin and continue stacking into the middle and top bins When all three bins are full the MFP stops printing Printing continues only when you remove paper from the top bin The MFP does not resume printing if you remove paper from the bottom bin or the middle bin before you remove paper from the top bin When the 3 bin mailbox is in stacker mode you cannot designate that a job be sent to a particular bin ET NOTE Do not remove paper from the top bin and then attempt to put it in place again This causes the pages to stack in the incorrect order e Function separator mode You can configure the bins to receive jobs that come from a specific MFP function such as printed jobs copy jobs or faxes For instance you can specify that all copy jobs are sent to the top bin The MFP stops functioning when the designated bin is full Printing copying orfaxing can continue only when you empty the bin See 3 bin mailbox output bins for information on configuring and using the optional 3 bin mailbox Stapler stacker The optional stapler stacker provides automatic stapling and stacking functionality for printed or copied jobs See Staple docu
257. quena n aaa 150 Neutral Grays iet err RED RD e er dc ges Elo E aM Rd 151 picieg mx e 151 Edge Control P 151 11 Copy Use the Copy SCreGr i bacca dde een dr cesa Dedi ete ccc dos b daz ea b cc erts Fe desta A 154 Set the default copy options ssssssssssssssssssssesssses eene nennen nennt enn n nenne rrere nnn enn 155 Basic COPY INStUCHONS PP E 156 ENWW vii Copy from the scanner glass idee epe La ee be Odd heu icd ge exe Debe a Dd E Dae Mig Does 156 Copy from the document feeder essent 156 Adjust the copy settings niet Ie te sene aee sese Ear esae MEE re EEE EUR edie 157 Copy two sided documents eececeeeneeceee cece eeeeeeeeetee cece acaaaaaeaaeceeeeeeeeeeeeeeeesetsasaaaaesaecaeeeeeeeneess 158 Copying two sided documents manually ccccccccecceceeeeeeeeeeeeeeeteeeeeeeeeeeeceennsaneaeeaeees 158 Copy two sided documents automatically sss 158 Copy tnixed size originals rero thier Eiern bruit E RRE DI RR ERE LETS PR PR RRRED DP RR RR RARPD sce E 160 Change the copy collation setting eee eee teen eee teeter eee e etre nennen nnne nnns 161 Copy photos and bOOKS loc nie eren ee aia eed eer Deities Fd us ERR e E Re ego 162 Combine copy jobs by using Job Build ssseeneeene nennen 163 Cancela copy JOD ck uu 164 12 Scan and send
258. r Mac OS X 1 Inthe Apple menu click System Preferences In the System Preferences box click Print and Fax Click Set Up Printers A Printer List displays Select the Installable Options panel 2 3 4 Select the HP product and then click Show Info on the Printers menu 5 6 Inthe Accessory Output Bins list select HP 3 Bin Mailbox 7 In the Mailbox Mode list select the appropriate operational mode and then click Apply Changes 104 Chapter 7 Paper and print media ENWW 8 Use product features e Economy settings e Job storage features ENWW 105 Economy settings Sleep and wake Set the sleep delay Use the sleep delay feature to set the period of time that the MFP must be idle before it enters the sleep mode The default setting is 45 minutes 1 2 3 4 Scroll to and touch Administration Touch Time Scheduling Touch Sleep Delay Touch the sleep delay setting that you want Set the wake time Use the wake time feature to wake the MFP at a set time each day 1 O OCN er UC cum X ON Scroll to and touch Administration Touch Time Scheduling Touch Wake Time Touch the day of the week for the wake time Touch Custom Touch Save Touch the appropriate options to set the correct hour minute and AM PM setting If you want to wake the MFP at the same time each day on the APPLY TO ALL DAYS screen touch Yes If you want to set the time for individual days touch No and repeat th
259. r Specific Options ENWW Job storage features 107 Use the proof and hold feature The proof and hold feature provides a quick and easy way to print and proof one copy of a job and then to print the additional copies To permanently store the job and prevent the device from deleting it when space is needed for something else select the Stored Job option in the driver Create a proof and hold job A CAUTION Ifthe device needs additional space to store newer proof and hold jobs the device deletes other stored proof and hold jobs starting with the oldest job To permanently store a job and prevent the device from deleting it when space is needed select the Stored Job option in the driver instead of the Proof and Hold option In the driver select the Proof and Hold option and type a user name and job name The device prints one copy of the job for you to proof Print the remaining copies of a proof and hold job At the device control panel use the following procedure to print the remaining copies of a job held on the hard disk 1 2 3 4 5 From the Home screen touch Job Storage Touch the Retrieve tab Scroll to and touch the job storage folder that holds the job Scroll to and touch the job that you want to print Touch the Copies field to change the number of copies to print Touch Retrieve Stored Job to print the document Delete a proof and hold job When you send a proof and hold job the device a
260. r automatic configuration from a DHCPv4 server If selected and a DHCP lease exists DHCP Release and DHCP Renew menus are available to set DHCP lease options Auto IP Use automatic link local IPv4 addressing An address in the form 169 254 x x is assigned automatically Manual Use the Manual Settings menu to configure TCP IPv4 parameters Specify the IP address to default to when the print server is unable to obtain an IP address from the network during a forced TCP IP reconfiguration for example when manually configured to use BootP or DHCP Auto IP A link local IP address 169 254 x x is set Legacy The address 192 0 0 192 is set consistent with older HP Jetdirect devices DHCP Release This menu appears if Config Method was set to DHCP and a DHCP lease for the print server exists No default The current DHCP lease is saved Yes The current DHCP lease and the leased IP address are released DHCP Renew This menu appears if Config Method was set to DHCP and a DHCP lease for the print server exists No default The print server does not request to renew the DHCP lease Yes The print server requests to renew the current DHCP lease Manual Settings Available only if Config Method is set to Manual Configure parameters directly from the printer control panel IP Address The unique IP address of the printer n n n n where n is a value from 0 to 255 Subnet Mask The subnet mask for the
261. r of pages per sheet that you have selected 118 Chapter9 Print tasks ENWW Print on both sides of the page duplex printing Automatic two sided duplex printing Specify two sided printing options in your software program or in the printer driver If you cannot see this option use the following information to make the duplex printing options available ENWW Verify that the printer driver is configured to show the two sided printing options automatic and manual To change or verify the configuration click the Start button choose Settings and click Printers and Faxes Then right click on the printer and select Properties On the Device Settings tab verify that the duplexer is shown as installed and that the Allow Manual Duplexing option is enabled After the two sided printing option appears select the appropriate settings in the printer driver software including the page and binding orientation Automatic two sided printing is not supported for certain media types e Transparencies e Envelopes e Labels e Heavy extra heavy cardstock and HP Tough paper The maximum weight paper for automatic duplex printing is 120 g m 32 Ib bond Automatic two sided printing only supports the following media sizes e Letter e Legal e B5 e Executive e 85x13 e A4 Manual two sided printing can support all sizes and more types of media excluding transparencies envelopes and labels If both automatic and manual two sided pri
262. r output increases the size of the output file Medium default Low small file Resolution 75 DPI Select the resolution Use a lower setting to create smaller files 150 DPI default 200 DPI 300 DPI ENWW Default Job Options menu 25 Default Print Options Administration gt Default Job Options gt Default Print Options Table 2 7 Default Print Options menu Menu item Sub menu item Values Description Copies Per Job Type a value Set the default number of copies for print jobs Default Paper Size List of supported sizes Select a paper size Default Custom Paper Unit of measure Millimeters Configure the default paper size that is used when the Size user selects Custom as the paper size for a print job Inches X Dimension Configure the width measurement for the Default Custom Paper Size Y Dimension Configure the height measurement for the Default Custom Paper Size Output Bin lt binname gt Select the default output bin for print jobs If optional trays are installed output bin options vary Print Sides 1 sided Select whether print jobs are single sided or double sided by default 2 sided 2 Sided Format Book style Use this feature to configure the default style for 2 sided print jobs If Book style is selected the placement Flip style of the back side of the page is the same as the front This option is for print jobs that are bound along the left edge If Flip style is selected the back s
263. r visit http www hp com recycle Select your country region for information on how to return your HP LaserJet printing supplies This product is capable of using recycled papers when the paper meets the guidelines outlined in the HP LaserJet Printer Family Print Media Guide This product is suitable for the use of recycled paper according to EN12281 2002 Material restrictions ENWW This HP product contains a battery that may require special handling at end of life The battery contained in this product includes Environmental product stewardship program 321 Type Carbon monofluoride lithium battery Weight 0 8 grams Location Formatter board User removable No Batterij niet weggooien maar inleveren als KCA X mg Sy EFE DEA 8 I This product contains mercury in the fluorescent lamp of the control panel liquid crystal display that might require special handling at end of life For recycling information you can visit http www hp com go recycle or contact your local authorities or the Electronics Industry Alliance http www eiae org Disposal of waste equipment by users in private households in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste elect
264. rJet CM4730 MFP 3 OntheFile menu click Properties 4 Select the Device Settings tab 5 Use either of the following methods to select the stapler stacker Scroll to Automatic Configuration select Update Now and then click Apply or Scroll to Accessory Output Bin select HP 500 sheet stapler stacker or HP 3 bin mailbox mailbox mode or HP 3 bin mailbox stacker mode or HP 3 bin mailbox function separator and click Apply Setting the color options Options on the Color tab control how colors are interpreted and printed from software programs You can choose either Automatic or Manual color options For more information see Manage printer color options on Windows computers e Select Automatic to optimize the color and halftone settings for text graphics and photographs The Automatic setting provides additional color options for programs and operating systems that support color management systems This setting is recommended for printing all color documents e Select Manual to adjust the color and halftone settings for text graphics and photographs If you are using a PCL driver you can adjust the RGB data If you are using the PS driver you can adjust RGB or CMYK data To set the color options 1 On the File menu in the software program click Print 2 Select the driver and then click Properties or Preferences 3 Click the Color tab 4 Inthe Color Options area select the option that you want to use 5 If you selected Ma
265. rating system palettes monitors and video cards and drivers Overhead transparency defects Overhead transparencies might display any of the image quality problems that any other type of media could display as well as defects specific to transparencies In addition because transparencies are pliable while in the print path they are subject to being marked by the media handling components ET NOTE Allow transparencies to cool at least 30 seconds before handling them On the printer driver s Paper tab select Transparency as the media type Also make sure that the tray is correctly configured for transparencies Check that the transparencies meet the specifications for this MFP Handle transparencies by the edges Skin oil on the surface of transparencies can cause spots and smudges Small random dark areas on the trailing edge of solid fill pages might be caused by transparencies sticking together in the output bin Try printing the job in smaller batches The selected colors are undesirable when printed Select different colors in the software program or printer driver If you are using a reflective overhead projector use a standard overhead projector instead Print quality problems associated with the environment The MFP is operating in excessively humid or dry conditions Verify that the printing environment is within specifications See Environmental specifications Print quality problems associated with jam
266. remove any jammed paper 16 Close the lower access door If the jam has cleared the print job will continue 17 If the jam is still not cleared and you are printing from tray 1 see Clear jams in tray 2 3 or 4 ENWW Jams 245 Clear jams in tray 1 E NOTE Ifthe protective insert does not eject properly when the printer is first installed follow this procedure to clear the jam 1 Perform the steps in Clear jams behind the right covers Remove loaded media Remove any jammed paper from the tray Reload the media Verify that the media is located correctly and is not above the fill tabs Some ne ue Wo Confirm that the guides are in the correct position Clear jams in tray 2 3 or 4 1 Perform the steps in Clear jams behind the right covers 2 Slide the indicated tray out and remove any jammed paper 3 Close the tray If the jam is cleared the print job will continue 246 Chapter 16 Problem solving ENWW 4 Ifthe paper jam still does not clear lift the tray and remove it from the MFP The following diagram shows an example of removing tray 2 5 Remove any paper jam behind the tray The following diagram shows a possible paper jam behind tray 2 Remove jams in trays 3 and 4 following the same procedure 6 Insert the paper tray ENWW Jams 247 Cle
267. rical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or the shop where you purchased the product Material Safety Data Sheet MSDS Material Safety Data Sheets MSDS for supplies containing chemical substances for example toner can be obtained by contacting the HP Web site at www hp com go msds or www hp com hpinfo community environment productinfo safety 322 Appendix D Regulatory information ENWW For more information To obtain information about these environmental topics e Product environmental profile sheet for this and many related HP products e HP s commitment to the environment e HP s environmental management system e HP send of life product return and recycling program e Material Safety Data Sheets Visit www hp com go environment or www hp com hpinfo globalcitizenship environment ENWW Environmental product stewardship program 323 Certificate of volatility This is a statement regarding the volatility of customer data stored in memory It also outlines how to erase secure data from the device Types of memory Volatile memory The MFP utilizes volatile m
268. ridge 12 000 pages 3 months Image transfer kit Replace Transfer Kit 120 000 pages 40 months Image fuser kit Replace Fuser Kit 150 000 pages 50 months Stapler cartridge Replace Stapler Cartridge 5000 pages ADF maintenance kit Replace Document Feeder 90000 pages Kit 1 Approximate average A4 letter size page count based on 5 coverage of individual colors Approximate life is based on 4 000 pages per month Change print cartridges ENWW When a print cartridge approaches the end of its useful life the control panel displays a message recommending that you order a replacement The MFP can continue to print using the current print cartridge until the control panel displays a message instructing you to replace the cartridge The MFP uses four colors and has a different print cartridge for each color black K magenta M cyan C and yellow Y Replace a print cartridge when the MFP control panel displays a Replace color Cartridge message The control panel display will also indicate the color that should be replaced if a genuine HP cartridge is currently installed Replacement instructions are included in the print cartridge box CAUTION If toner gets on clothing wipe it off with a dry cloth and wash the clothes in cold water Hot water sets toner into fabric ET NOTE For information about recycling used print cartridges go to http www hp com go recycle Replace supplies 211 Clean the MFP To m
269. ridge motor Press Stop when ready to stop this test Rotating Motor To exit press STOP The MFP is executing a component test and the component selected is a motor Press Stop when ready to stop this test SANITIZING DISK lt X gt COMPLETE Do not power off The hard disk is being cleaned Contact the network administrator SCAN FAILURE Press Start to rescan The scan was unsuccessful and the document needs to be rescanned If necessary reposition the document to rescan it and then press Start Size mismatch in tray XX SMTP Gateway The media in the listed tray does not match the size specified for that tray The SMTP gateway has exceeded a time out value 1 Load the correct media 2 Ifthe message persists contact HP Support at http www hp com support ljom4730mfp Verify the e mail server address Contact the network administrator The Digital Sending Service at IP Address does not service this MFP Contact administrator The MFP cannot communicate with the specified IP address Verify the IP address Contact the network administrator The Digital Sending Service must be upgraded to support this version of the MFP firmware Contact administrator The Digital Sending Service is not supported by the version of the firmware that is currently installed for the MFP Check the firmware version Contact the network administrator The folder you have ent
270. rint color samples at the MFP using the control panel 1 Touch Information 2 Touch Sample Pages Fonts 3 Touch CMYK Samples or RGB Samples The pages will print 146 Chapter 10 Using color ENWW Manage printer color options on Windows computers Setting color options to Automatic typically produces the best possible print quality for the most common printing requirements However for some documents setting the color options manually can enhance the way the document appears Examples of these documents include marketing brochures that contain many images or documents that are printed on a media type that is not listed in the printer driver For Windows you can print in grayscale or change the color options by using settings found on the Color tab in the printer driver Print in grayscale Select the Print in Grayscale option from the printer driver to print a document in black and white Setting the color options in Windows Options on the Color tab control how colors are interpreted and printed from software programs You can choose either Automatic or Manual color options For more information see Manage printer color options on Windows computers Select Automatic to optimize the color and halftone used for each element in a document such as text graphics and photographs The Automatic setting provides additional color options for software programs and operating systems that support color management systems This settin
271. rk activities This information appears in a Web browser such as Microsoft Internet Explorer Netscape Navigator Apple Safari or Firefox The embedded Web server resides on the device It is not loaded on a network server The embedded Web server provides an interface to the device that anyone who has a network connected computer and a standard Web browser can use No special software is installed or configured but you must have a supported Web browser on your computer To gain access to the embedded Web server type the IP address for the device in the address line of the browser To find the IP address print a configuration page For more information about printing a configuration page see Information pages For a complete explanation of the features and functionality of the embedded Web server see Embedded Web server Network utilities 85 HP Easy Printer Care software The HP Easy Printer Care software is a program that you can use for the following tasks e Discovering printers on the network and checking the status of each device e Setting and viewing device and supplies alerts for multiple printers at the same time e Shopping online for supplies e Using HP online troubleshooting and maintenance tools You can use the HP Easy Printer Care software when the device is directly connected to your computer or a network running Windows Macintosh is not supported To download the HP Easy Printer Care Software go to www hp com go ea
272. rmation e Set the type of media that is loaded in each tray e Determine the remaining life for all supplies and order new ones e View and change tray configurations e View and change the MFP control panel menu configuration e View and print internal pages e Receive notification of MFP and supplies events e View and change network configuration To use the embedded Web server you must have Microsoft Internet Explorer 5 01 or later or Netscape 6 2 or later for Windows Mac OS and Linux Netscape only Netscape Navigator 4 7 is required for HP UX 10 and HP UX 11 The embedded Web server works when the MFP is connected to an IP based network The embedded Web server does not support IPX based MFP connections You do not have to have Internet access to open and use the embedded Web server When the MFP is connected to the network the embedded Web server is automatically available ET NOTE For complete information about using the embedded Web server see the Embedded Web Server User Guide which is on the HP Color LaserJet CM4730 MFP series software CD Open the embedded Web server To open the embedded Web server type the IP address or host name of the MFP in a supported Web browser If you do not know the IP address or host name print a configuration page The embedded Web server has four tabs e Information tab e Settings tab e Digital Sending tab e Networking tab The embedded Web server also has other links th
273. rom misuse improper storage or operation outside of the published environmental specifications for the printer product or c exhibit wear from ordinary use To obtain warranty service please return the product to place of purchase with a written description of the problem or contact HP customer support At HP s option HP will either replace products that prove to be defective or refund your purchase price TO THE EXTENT ALLOWED BY LOCAL LAW THE ABOVE WARRANTY IS EXCLUSIVE AND NO OTHER WARRANTY OR CONDITION WHETHER WRITTEN OR ORAL IS EXPRESSED OR IMPLIED AND HP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE TO THE EXTENT ALLOWED BY LOCAL LAW IN NO EVENT WILL HP OR ITS SUPPLIERS BE LIABLE FOR DIRECT SPECIAL INCIDENTAL CONSEQUENTIAL INCLUDING LOST PROFIT OR DATA OR OTHER DAMAGE WHETHER BASED IN CONTRACT TORT OR OTHERWISE THE WARRANTY TERMS CONTAINED IN THIS STATEMENT EXCEPT TO THE EXTENT LAWFULLY PERMITTED DO NOT EXCLUDE RESTRICT OR MODIFY AND ARE IN ADDITION TO THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU Color LaserJet Image Fuser Kit and Image Transfer Kit Limited Warranty Statement 307 Availability of support and service Around the world HP provides a variety of service and support options for purchase Availability of these programs will vary depending upon your location 308 Appendix B Ser
274. rovide access to device features Use the Apple PostScript printer driver that comes with the computer e HP Printer Utility Use the HP Printer Utility to set up device features that are not available in the printer driver e Name the device e Assign the device to a zone on the network e Assign an internet protocol IP address to the device e Download files and fonts e Configure the device for IP or AppleTalk printing You can use the HP Printer Utility when your device uses a universal serial bus USB cable or is connected to a TCP IP based network For more information see HP Printer Utility for Macintosh ET NOTE The HP Printer Utility is supported for Mac OSX V10 2 or later 70 Chapter 4 Software for Macintosh ENWW Remove software from Macintosh operating systems To remove the software from a Macintosh computer drag the PPD files to the trash can ENWW Remove software from Macintosh operating systems 71 72 Chapter4 Software for Macintosh ENWW 5 Software for other operating systems e HP Web Jetadmin e UNIX ENWW 73 HP Web Jetadmin Use HP Web Jetadmin to manage HP Jetdirect connected printers within your intranet HP Web Jetadmin is a browser based management tool that can be installed on the following systems Fedora Core and SuSE Linux Windows 2000 Professional Server and Advanced Server Windows Server 2003 Windows XP Professional When installed on a host server any client can access
275. rtt numbers EMG otii p vita e Metti e Mex VR UE Mags E a aA a aaa EN 299 Dwerteglge o 299 sisIpier groom H O 299 MIETNRENISIASINURMII A MM 299 Customer replaceable units sess ennemis 300 MOMON T 300 Cables and Interfaces eec pee a teer ee e LR ETAT ERE PADRE CE Ce VA ee OPI RH SEN EEEa 300 Appendix B Service and support Hewlett Packard limited warranty statement sssssssssssseeeee eene nennen 301 Customer self repair warranty service ssssssssssessssseeeneeeeeeene enne nennen nennen 303 HP ouslomer Cae TUM 304 Limited warranty for print cartridges and image drums sese 306 Color LaserJet Image Fuser Kit and Image Transfer Kit Limited Warranty Statement 307 Availability of support and service cecceeeeecee cee ee eee eeeeeteceeeaaeaaeaeeeeeeeeeeeseesecaaaaeaaeeeeeeeeeeeeeeesseaeeas 308 HP maintenance agreermelts oce eret ceret eee adhd ies epa eaaet I dao TER e HR Ee TERR RR aes 309 On site service agreements ssssssssssssssseeeeeen eene nennen nennen 309 Priority Onsite ServiCe etie ii E eae x E EE e ERRAT GR REX HU EERTE EYE PX RRR RATES REEL RED 309 Next day onsite service sssssssssssesseeeeeenee mener ee nennen nennen 309 Weekly volume on site service
276. s If you are using the 3 bin mailbox three output bins are available Configure these bins as individual mailboxes or combine them to function as a single bin to stack documents ENWW Select the output bin 101 3 bin mailbox output bins ADF output bin for copy originals The top two bins each hold up to 100 sheets of paper A sensor stops the MFP when a bin is full MFP operation continues when you empty or reduce the amount of media in the bin The lower bin holds up to 500 sheets of paper Select an output location If possible select an output location bin through your program or driver Where and how you make selections depends on your program or driver If you cannot select an output location from the program or driver set the default output location on the MFP control panel 1 2 3 4 5 Scroll to and touch Administration Touch Default Job Options Touch Default Copy Options or Default Print Options Touch Output Bin Touch the desired output bin Configure the 3 bin mailbox Configure the printer driver to recognize the 3 bin mailbox in Windows 1 2 3 Open the Printers folder Select HP Color LaserJet CM4730 MFP On the File menu click on Properties 102 Chapter 7 Paper and print media ENWW 4 5 Select the Device Settings tab Use either of the following methods to select the stapler stacker e Scroll down to Automatic Configuration select Update Now and clic
277. s Make sure that all media is cleared from the paper path The MFP recently jammed Print two to three pages to clean the MFP The media does not pass through the fuser causing image defects to appear on subsequent documents Print two to three pages to clean the MFP However if the problem persists see the next section ENWW Correct print quality and copy quality problems 265 Print quality troubleshooting pages The print quality troubleshooting pages provide information on aspects of the MFP that affect print quality 1 Scroll to and touch Administration 2 Scroll to and touch Troubleshooting 3 Touch PQ Troubleshooting 4 Touch Print The message Printing PQ troubleshooting appears on the display until the MFP finishes printing the print quality troubleshooting information The MFP returns to the Ready state after printing the print quality troubleshooting information The print quality troubleshooting information includes one page for each color black magenta cyan and yellow MFP statistics related to print quality instructions on interpreting the information and procedures to solve print quality problems If following the procedures recommended by the print quality troubleshooting pages do not improve print quality go to http Awww hp com support licm4730mfp Print quality troubleshooting tool The print quality troubleshooting tool helps you identify and troubleshoot print quality issues for the HP Color
278. s For example type C N copy b C MY DOCUMENTS 3500FW RFU NXAYOUR SERVERNV YOUR COMPUTER Press Enter on the keyboard The control panel shows a message that indicates the progress of the firmware upgrade At the end of the upgrade process the control panel shows the Ready message The message One File Copied appears on the computer screen Use the HP Jetdirect firmware The HP Jetdirect network interface in the MFP has firmware that can be upgraded separately from the MFP firmware This procedure requires that you install HP Web Jetadmin Version 7 0 or later on your 204 Chapter 14 Manage the MFP ENWW ENWW computer See HP Web Jetadmin software Complete the following steps to update the HP Jetdirect firmware by using HP Web Jetadmin 1 2 10 11 Open the HP Web Jetadmin program Open the Device Management folder in the drop down list in the Navigation panel Navigate to the Device Lists folder Select the device that you want to update In the Device Tools drop down list select Jetdirect Firmware Update Under Jetdirect firmware version the HP Jetdirect model number and current firmware version are listed Make a note of these Go to http www hp com go wja_firmware Scroll down to the list of HP Jetdirect model numbers and find the model number you wrote down Look at the current firmware version for the model and see if it is later than the version you wrote down If it is right click on the
279. s are out this message is displayed 1 Replace the empty cartridges 2 Ifthe message persists contact HP Support at http www hp com support ljcm4730mfp Replace Supplies Override in use The MFP is set to continue printing even though a print cartridge has reached end of life From the control panel Home screen touch Supplies Status and then touch the Supplies tab so you can see which supplies are out Replace the necessary print cartridge 236 Chapter 16 Problem solving ENWW Table 16 1 Control panel messages continued Control panel message Description Recommended action Replace Supplies Using black A color supply or supplies has reached the out condition and the Color Supply Out menu item is set to Autocontinue black No user input is required for printing to continue Printing continues in black Replace Transfer Kit The transfer unit is at end of life Printing can continue but print quality might be reduced Replace the transfer kit 1 Open the right side covers 2 Lower the transfer unit by pulling downward on the green handle at the top of the unit 3 Depress the small blue latches located on either side of the bottom of the transfer unit and lift the unit out of the MFP 4 Install the new transfer unit 5 Close the right side covers Rotating lt color gt Motor A component test is in progress the component selected is the lt color gt cart
280. s at the top and bottom of the slot and then slide the board back into the MFP ET NOTE To prevent damage to the formatter board ensure the formatter board is aligned in the tracks Install memory and fonts 337 8 Reinsert the formatter pressure release tabs by squeezing them together and pushing them into place 9 Reconnect the power cable and interface cables and turn the MFP on Enabling memory If you installed a memory DIMM set the MFP driver to recognize the newly added memory Enable memory for Windows 98 and Me 1 On the Start menu point to Settings and click Printers 2 Right click the printer and select Properties 3 On the Configure tab click More 4 Inthe Total Memory field type or select the total amount of memory that is now installed 5 Click OK 338 Appendix E Install memory and print server cards ENWW Enable memory for Windows 2000 and XP ENWW 1 2 3 4 5 On the Start menu point to Settings and click Printers or Printers and Faxes Right click the printer and select Properties On the Device Settings tab click Printer Memory in the Installable Options section Select the total amount of memory that is now installed Click OK Install memory and fonts 339 Install an HP Jetdirect or EIO print server card The HP Color LaserJet CM4730 MFP is equipped with an embedded HP Jetdirect print server port If desired you
281. s being generated The printer will return to the ready state upon completion of the page No action is necessary Printing Demo Page This message displays while the demo page is being generated The device will return to the ready state upon completion of the page No action is necessary Printing Diagnostics Page This message displays while the diagnostics page is being generated The device will return to the ready state upon completion of the page No action is necessary ENWW Control panel messages 235 Table 16 1 Control panel messages continued Control panel message Description Recommended action Printing PQ Troubleshooting This message is displayed while the print quality troubleshooting test is being generated The device will return to the ready state upon completion of the test No action is necessary Printing RGB Samples This message displays while the print quality troubleshooting test is being generated The device will return to the ready state upon completion of the page No action is necessary Reattach output bin The standard output bin was detached when the MFP was turned on or the cable on the stapler stacker or the 3 bin mailbox is not connected to the MFP Turn the MFP off If you are using the stapler stacker or the 3 bin mailbox make sure that the cable is connected to the MFP Reattach the output bin and then turn the MFP on Observe the LED on
282. s field to change the number of copies to print Touch Retrieve Stored Job to print the document Delete a personal job ENWW A personal job is automatically deleted from the device hard disk after you release it for printing If you want to delete the job without printing it use this procedure 1 2 3 4 From the Home screen touch Job Storage Touch the Retrieve tab Scroll to and touch the job storage folder that holds the personal job Scroll to and touch the personal job that you want to delete 2333 E NOTE A personal job will have a Fl lock symbol next to it Touch the PIN field Use the numeric keypad to type the PIN and then touch OK Touch Delete Job storage features 109 Use the QuickCopy feature The QuickCopy feature prints the requested number of copies of a job and stores a copy on the device hard disk Additional copies of the job can be printed later This feature can be turned off in the printer driver The default number of different QuickCopy jobs that can be stored on the device is 32 At the control panel you can set a different default number See Navigate the Administration menu Create a QuickCopy job A CAUTION Ifthe device needs additional space to store newer QuickCopy jobs the device deletes other stored QuickCopy jobs starting with the oldest job To permanently store a job and prevent the device from deleting it when space is needed select the Job Storage opt
283. s not needed and will be skipped In this case the MFP will reach the ready state approximately one minute sooner While the MFP is calibrating and cleaning the MFP will pause printing for the amount of time it takes to complete the calibration or cleaning For most calibrations and cleaning the MFP will not interrupt a print job but will wait for the job to complete before calibrating or cleaning 1 Scroll to and touch Administration 2 Scroll to and touch Troubleshooting 3 Touch Quick Calibration or touch Full Calibration 4 Touch Calibrate Repetitive defect ruler If defects repeat at regular intervals on the page use this ruler to identify the cause of the defect Place the top of the ruler at the first defect The marking that is beside the next occurrence of the defect indicates which component needs to be replaced ENWW Correct print quality and copy quality problems 285 Y wv yy o9 Q gt o 1 First occurrence of the defect the distance from the top of the page to the defect might vary 2 Black print cartridge 34 3 mm 1 35 inches 3 Print cartridge or transfer roller if the defect occurs in only one color the defective part is the print cartridge if the defect occurs in all colors the defective part is the ETB 37 7 mm 1 48 inches 4 Cyan magenta and yellow print cartridges 38 5 mm 1 52 inches 5 Print cartridge 42 7 mm 1 68 inch
284. se To obtain warranty service please return the product to place of purchase with a written description of the problem and print samples or contact HP customer support At HP s option HP will either replace products that prove to be defective or refund your purchase price TO THE EXTENT ALLOWED BY LOCAL LAW THE ABOVE WARRANTY IS EXCLUSIVE AND NO OTHER WARRANTY OR CONDITION WHETHER WRITTEN OR ORAL IS EXPRESSED OR IMPLIED AND HP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE TO THE EXTENT ALLOWED BY LOCAL LAW IN NO EVENT WILL HP OR ITS SUPPLIERS BE LIABLE FOR DIRECT SPECIAL INCIDENTAL CONSEQUENTIAL INCLUDING LOST PROFIT OR DATA OR OTHER DAMAGE WHETHER BASED IN CONTRACT TORT OR OTHERWISE THE WARRANTY TERMS CONTAINED IN THIS STATEMENT EXCEPT TO THE EXTENT LAWFULLY PERMITTED DO NOT EXCLUDE RESTRICT OR MODIFY AND ARE IN ADDITION TO THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU 306 Appendix B Service and support ENWW Color LaserJet Image Fuser Kit and Image Transfer Kit Limited Warranty Statement ENWW This HP product is warranted to be free from defects in materials and workmanship until the printer provides a low life indicator on the control panel This warranty does not apply to products that a have been refurbished remanufactured or tampered with in any way b experience problems resulting f
285. seconds for packet transmission and response RTT Max Shows the maximum detected roundtrip time RTT from 0 to 4096 milliseconds for packet transmission and response RTT Average Shows the average round trip time RTT from 0 to 4096 milliseconds for packet transmission and response Ping In Progress Shows whether a ping test is in progress Yes indicates a test in progress and No indicates that a test completed or was not run Refresh When viewing the ping test results this item updates the ping test data with current results Select Yes to update the data or No to maintain the existing data However a refresh automatically occurs when the menu times out or you manually return to the main menu Link Speed The link speed and communication mode of the print server must match the network The available settings depend on the device and installed print server Select one of the following link configuration settings CAUTION If you change the link setting network communications with the print server and network device might be lost Auto default The print server uses auto negotiation to configure itself with the highest link speed and communication mode allowed If auto negotiation fails either 100TX HALF or 10TX HALF is set depending on the detected link speed of the hub switch port A 1000T half duplex selection is not supported 10T Half 10 Mbps half duplex operation 10T Full
286. sit these Web sites Connecting might require that you close the embedded Web server and reopen it HP Instant Support Connects to the HP Web site to help you find solutions This service analyzes your MFP error log and configuration information to provide diagnostic and support information specific to your MFP Order Supplies Connect to a Web site where you can order genuine HP supplies such as print cartridges and media Product Support Connects to the support site for the HP Color LaserJet CM4730 MFP series Embedded Web server 187 HP Easy Printer Care software HP Easy Printer Care software is a software program that you can use for the following tasks e Check the printer status e Check supplies status e Setup alerts e Gain access to troubleshooting and maintenance tools You can use the HP Easy Printer Care software when the printer is directly connected to your computer or when it is connected to a network You must perform a complete software installation to use the HP Easy Printer Care software ET NOTE You do not have to have Internet access to open and use the HP Easy Printer Care software However if you click a Web based link you must have Internet access to go to the site associated with the link For more information on HP Easy Printer Care software visit http www hp com go easyprintercare Supported operating systems The HP Easy Printer Care software is supported for Windows 2000 and Windows
287. sks 113 printer languages 6 printing booklets 122 output bin selecting 101 speed specifications 5 printing from tray 2 3 or4 94 priority onsite service 309 priority settings 66 problem solving color fade 271 272 Error button control panel touchscreen 16 fingerprints 273 horizontal lines 266 loose toner 274 media damage 277 messages types of 225 misaligned colors 268 networks 34 repetitive defects 270 skewed page 279 smeared toner 275 specs 278 vertical lines 269 white areas 276 processor speed 5 productinfo 1 proof and hold jobs 108 ENWW protocol configuration page printing 38 PS Emulation drivers 62 Q quality troubleshooting 263 R Ready light locating 14 real time clock 199 reattach output bin error message 236 recipient lists 171 recycling HP printing supplies returns and environmental program 321 reducing documents 117 regulatory statements Declaration of Conformity 319 environmental product stewardship program 320 laser statement for Finland 327 remote firmware update RFU 202 removing Macintosh software 71 repeating defects troubleshooting 285 repetitive defects 270 repetitive defects problem solving 270 replacing staple cartridges 134 reset button 14 Resets menu control panel 54 resize documents Macintosh 126 resizing documents 117 resolution specifications 5 troubleshooting quality 263 retention job accessing 107 features 107 personal 109 proof and hold 108 QuickCopy 110
288. st of control panel menus and possible values see Use the control panel Configuration page Shows device settings and installed accessories 1 From the Home screen touch Administration 2 Touch Information 3 Touch Configuration status Pages 4 Touch Configuration status Pages 5 Touch Print 2 NOTE Ifthe device contains an HP Jetdirect print server or an optional hard disk drive additional configuration pages print that provide information about those devices Supplies status page Shows print cartridge toner levels 1 From the Home screen touch Administration 2 Touch Information 3 Touch Configuration status Pages 4 Touch Supplies Status Page 5 Touch Print EZ NOTE Ifyou are using non HP supplies the supplies status page might not show the remaining life for those supplies Usage page Shows a page count for each size of paper printed the number of one sided simplexed or two sided duplexed pages and the average percentage of coverage File directory Contains information for any mass storage devices such as flash drives 1 From the Home screen touch Administration 2 Touch Information 3 Touch Configuration status Pages Touch Usage Page 5 Touch Print 1 From the Home screen touch Administration 2 Touch Information 3 Touch Configuration status Pages 182 Chapter 14 Manage the MFP ENWW ENWW Page description How to print
289. stored 111 rollers cleaning ADF 214 ruler repetitive defect 285 S safety statements 325 scale documents Macintosh 126 scaling documents 117 scanner calibration 50 220 scanner glass cleaning 212 scanning speed specifications 5 scanning e mail validating gateway addresses 288 scanning to e mail about 165 169 address books 171 configuring 166 embedded Web server settings 186 error messages 233 234 237 238 sending documents 169 troubleshooting 224 scanning to e mail address books 171 control panel settings 168 job settings 173 LDAP support 166 loading documents 169 recipient lists 171 sending documents 169 SMTP support 166 scanning to folder 174 scanning to workflow 175 Secure Disk Erase 197 security disk erase 197 Foreign Interface Harness FIH 196 locking control panel menus 198 settings 34 security features 7 Send Setup menu 42 Send to Folder 174 Send to Workflow 175 Index 349 sending to e mail about 165 166 169 address books 171 embedded Web server settings 186 error messages 233 234 237 238 sending documents 169 troubleshooting 224 validating gateway addresses 288 sending to e mail address books 171 job settings 173 LDAP support 166 loading documents 169 recipient lists 171 sending documents 169 settings 168 SMTP support 166 service agreements 305 309 HP authorized dealers 305 Service menu control panel 55 Services tab Macintosh 132 settings driver shortcuts Macintosh 126
290. support 304 temperature requirements 208 temperature requirements 315 tests networks 34 time setting 27 199 ENWW Time Scheduling menu control panel 27 timeout settings 31 top cover locating 9 touchscreen cleaning 212 tray 1 insert or close error message 234 load error message 234 locating 9 unexpected size or type error message 229 trays automatic media sensing 99 configure 98 double sided printing 131 included 2 insert or close error message 234 load 93 specifications physical 311 unexpected size or type error message 229 troubleshooting accessories 260 ADF output quality 280 blank pages 280 checklist 222 color printing problems 263 control panel 224 control panel messages numerical 226 digital sending 224 duplexing 259 EPS files 293 error messages alphabetical list 226 error messages numerical list 226 gateway addresses 288 lines 281 283 Macintosh problems 292 media handling problems 256 network printing 290 overhead transparencies 265 quality 263 repeating defects 285 skewed pages 282 transparencies 258 TrueType fonts included 6 two sided copying 158 two sided printing control panel settings 120 129 error messages 232 233 typefaces included 6 U unable to connect copy or send 238 unexpected size or type error messages 229 uninstalling Macintosh software 71 universal print driver 64 upgrading firmware 202 usage page printing 182 USB co
291. syprintercare Other components and utilities Windows Macintosh OS e Software installer automates the printing system e The HP Printer Utility change device settings view installation status and set up printer event notification from a Mac This utility is supported for Mac OS X V10 2 and later e Online Web registration 86 Chapter6 Connectivity ENWW 7 ENWW Paper and print media e Understand paper and print media use e Supported paper and print media sizes e Custom paper sizes e Special paper or print media guidelines e Load paper and print media e Configure trays e Select the output bin 87 Understand paper and print media use This product supports a variety of paper and other print media in accordance with the guidelines in this user guide Paper or print media that does not meet these guidelines might cause the following problems e Poor print quality e Increased jams e Premature wear on the product requiring repair For best results use only HP brand paper and print media designed for laserjets or multiuse Do not use paper or print media made for inkjet printers Hewlett Packard Company cannot recommend the use of other brands of media because HP cannot control their quality It is possible for paper to meet all of the guidelines in this user guide and still not produce satisfactory results This might be the result of improper handling unacceptable temperature and or
292. t Select a different language for control panel messages When you select a new language the keyboard layout might also change Key Press Sound On default Off Use this feature to specify whether you hear a sound when you touch the screen or press buttons on the control panel Inactivity Timeout Type a value between 10 and 300 seconds The factory Specify the amount of time that elapses between any activity on the control panel and the device resetting to the default settings default is 60 seconds Warning Error Clearable Warnings On Set the amount of time that a clearable Behavior warning appears on the control panel Job default Continuable Events Auto continue 10 seconds default Touch OK to continue Configure the device behavior when the device encounters certain errors Jam Recovery Auto default Off On Configure how the device handles pages that are lost during a jam ENWW Device Behavior menu 43 Table 2 15 Device Behavior menu continued Menu item Sub menu item Sub menu item Values Description Tray Behavior Use Requested Tray Exclusively default First Control how the device handles jobs that have specified a specific input tray Manually Feed Prompt Always default Unless Loaded Specify how a prompt should appear when the type or size for a job does not match the specified tray and the device pulls from the multipur
293. t is located on the back of the MFP ET NOTE This connector cannot be used by the 3 bin mailbox or stapler stacker accessories Figure 6 3 Auxiliary connection 1 Auxiliary connection port Jetlink 80 Chapter6 Connectivity ENWW Network configuration You might need to configure certain network parameters on the device You can configure these parameters in the following locations e Installation software e Device control panel e Embedded Web server e Management software HP Web Jetadmin or HP LaserJet Utility for Macintosh ET NOTE For more information about using the embedded Web server see Embedded Web server For more information on supported networks and network configuration tools see the HP Jetdirect Print Server Administrator s Guide The guide comes with printers in which an HP Jetdirect print server is installed This section contains the following information about configuring network parameters e Configure TCP IPv4 parameters e Configure TCP IPv6 parameters e Disable network protocols optional e HP Jetdirect EIO print servers Configure TCP IPv4 parameters If your network doesn t provide automatic IP addressing through DHCP BOOTP RARP or another method you might need to enter the following parameters manually before you can print over the network e P address 4 bytes e Subnet mask 4 bytes e Default gateway 4 bytes Change the IP address ENWW You
294. t name for your SMTP server If you are connecting through a DSL or cable connection contact the internet service provider to obtain the SMTP server IP address LDAP is used to gain access to a database of information When the device uses LDAP it searches a global list of e mail addresses As you begin to type the e mail address LDAP uses an auto complete feature that supplies a list of e mail addresses that match the characters you type As you type additional characters the list of matching e mail addresses becomes smaller The device supports LDAP but a connection to an LDAP server is not required in order for the device to be able to send to e mail ET NOTE If you need to change the LDAP settings you must change them by using the embedded Web server For more information see Embedded Web server or see the Embedded Web Server User Guide on the device CD Configure e mail server settings Consult your system administrator or use the control panel to find the IP address for the SMTP server Then use the following procedures to manually configure and test the IP address Configure the SMTP gateway address 1 2 3 4 From the Home screen touch Administration Touch Initial Setup Touch E mail Setup and then touch SMTP Gateway Type the SMTP gateway address either as an IP address or as a fully qualified domain name If you do not know the IP address or domain name contact the network administrator Touch OK
295. t number to it Type the name of the primary contact who will receive information about the MFP Embedded Web server 185 e Language Determine the language in which to show the embedded Web server information e Date amp Time Use this page to set the correct date and time for the device Once the time is set the device s real time clock maintains the accurate time e Wake Time page Wake Time can be set to wake the MFP at a certain time on a daily basis Only one wake time can be set per day however each day can have a different wake time You can also set the time delay for Sleep Mode on this page Digital Sending tab Use the pages on the Digital Sending tab to configure the digital sending features E NOTE Ifthe MFP is configured to use the optional HP Digital Sending Software the options on these tabs are not available Instead all digital sending configuration is performed by using the HP Digital Sending Software e General page Set up contact information for the system administrator e Send to e mail page Configure the e mail settings for digital sending You can specify the SMTP server the default From address and the default subject You can also set the maximum file size that is allowed for attachments e Addressing page Configure the LDAP server settings for digital sending The LDAP server can be used to retrieve e mail addresses for digital sending Select the check box at the top of this page to enable t
296. tem Several categories of HP ImageREt have been developed for a variety of user needs The system uses key color laser technologies including image enhancements smart supplies and high resolution imaging to provide superior images for general office documents and marketing collateral Optimized for printing on HP color laser high gloss papers HP Image REt 3600 provides superior results on all supported media and under a variety of environmental conditions 138 Chapter 10 Using color ENWW Restrict color use The HP Color LaserJet CM4730 MFP Series includes a Restrict Color setting A network administrator can use the setting to restrict user access to the color printing and copying features in order to conserve color toner If you are unable to print in color see your network administrator Restrict color printing 1 2 3 4 5 6 Scroll to and touch Administration Touch Management Touch Restrict Color Use Touch Color printing access Select one of the following options e Disable Color This setting denies color printing capabilities to all users e Enable Color default This setting allows color printing capabilities for all users e Color If Allowed The setting allows the network administrator to allow color use for select users and or applications Use the embedded Web server to designate which users and or applications can print in color Touch Save For more information about restricting and reporti
297. tended Service 305 extended warranty 309 e mail address books 171 auto complete function 170 control panel settings 168 job settings 173 LDAP support 166 loading documents 169 recipient lists 171 sending documents 169 SMTP support 166 Index 345 F fans troubleshooting 224 fax accessory connecting phone line 178 models including 3 part number 299 printing schedule 28 Fax Activity Log clearing 54 fax reports printing 18 183 Fax Setup menu 39 faxing digital 180 features 2 5 file directory printing 182 fingerprints 273 fingerprints problem solving 273 firmware upgrading 202 first page blank 117 use different paper flash memory card installing 334 folders error messages 234 sending to 174 fonts EPS files troubleshooting 293 included 6 list printing 19 183 Foreign Interface Harness FIH 7 11 196 formatter cover locating 9 formatter lights 261 FTP sending to 175 function separator mode 3 bin mailbox 298 fuser error messages 230 116 126 G gateways configuring 166 error messages 233 testing 167 validating addresses 288 glass cleaning 212 sizes supported 169 graphical display control panel 14 346 Index grayscale printing 147 150 H hard disk erasing 197 heartbeat LED 261 held jobs 108 Help button control panel touchscreen 16 help control panel 16 Home button control panel touchscreen 16 Home screen control panel 15 Horizontal lines 266 horizontal lines problem solving 266
298. ter features Select the orientation that is most often used for print jobs Select Portrait if the short edge is at the top or Landscape if the long edge is at the top Font Source Select the source from the list Select the font source for the user soft default font Font Number Type the font number The range is between 0 and 999 The factory default is Specify the font number for the user soft default font by using the source that is specified in the Font Source menu item The device assigns a number to each font and 0 lists it on the PCL font list available from the Administration menu Font Pitch Type a value If Font Source and Font Number indicate a between 0 44 and 99 99 The factory default is 10 00 contour font use this feature to select a default pitch for a fixed spaced font Font Point Size Type a value between 4 00 and 999 75 The factory default is 12 00 If Font Source and Font Number indicate a contour font use this feature to select a default point size for a proportional spaced font Symbol Set Append CR to LF PC 8 default 50 additional symbol sets from which to choose No default Yes Select any one of several available symbol sets from the control panel A symbol set is a unique grouping of all the characters in a font Configure whether a carriage return CR is appended to each line feed LF encountered in backwards compatible
299. test page to use for the Finishing Paper Path Test Manual Sensor Test 1 This item performs tests to determine whether the paper path sensors are operating correctly Manual Sensor Test 2 This item performs tests to determine whether the paper path sensors are operating correctly 52 Chapter2 Control panel ENWW Table 2 17 Troubleshooting menu continued Menu item Sub menu item Sub menu item Values Description Component Test Exercise individual parts independently to isolate noise leaking or other issues To start the test select one of the components The test runs the number of times specified in the Repeat option You might be prompted to remove parts from the device during the test Press the Stop button to abort the test Print Stop Test Continuous value from 0 to 60 000 Isolate faults by stopping the device during the print cycle and observing where in the milliseconds process the image degrades To run the test Default 0 specify a stop time The next job that is sent to the device stops at the specified time in the process Color Band Test Test Page Print Prints a page that helps identify arcing in the high voltage power supplies Copies Specify the number of copies to print for the Color Band test Scanner Tests A service technician can use this menu item to diagnose potential problems with the device scanner Control Panel LEDs Verify that the comp
300. that came in the box with the MFP HP service information To locate HP Authorized Dealers in the United States or Canada call 800 243 9816 United States or 800 387 3867 Canada Or go to http www hp com go cposupportguide For service for your HP product in other countries regions call the customer support number for your country region See the flyer that came in the box with the MFP HP service agreements Call 800 HPINVENT 800 474 6836 U S or 800 268 1221 Canada Out of Warranty Service 800 633 3600 Extended Service Call 800 HPINVENT 800 474 6836 U S or 800 268 1221 Canada Or go to the HP Care Pack Services Web site at http www hpexpress services com HP support and information for Macintosh computers Visit http www hp com go macosx for Mac OS X support information and HP subscription service for driver updates Visit http www hp com go mac connect for products designed specifically for the Macintosh user HP customer care 305 Limited warranty for print cartridges and image drums This HP Print Cartridge is warranted to be free from defects in materials and workmanship This warranty does not apply to print cartridges that a have been refilled refurbished remanufactured or tampered with in any way b experience problems resulting from misuse improper storage or operation outside of the published environmental specifications for the printer product or c exhibit wear from ordinary u
301. the automatic collation is on the pages print in this order 1 2 3 1 2 3 If automatic collation is off the pages print in this order 1 1 2 2 3 3 To use the automatic collation the original document size must fit into the memory If it does not the device makes only one copy and a message appears notifying you of the change If that happens use one of the following methods to finish the job e Splitthe job into smaller jobs that contain fewer pages e Make only one copy of the document at a time e Turn off the automatic collation The collation setting you select is in effect for all copies until you change the setting The default setting for automatic copy collation is On 1 Onthe control panel touch Copy 2 Touch Staple Collate or Collate 3 Touch Off 4 Touch OK Change the copy collation setting 161 Copy photos and books Copy a photo ET NOTE Photos should be copied from the flatbed scanner not from the document feeder 1 Lift the lid and place the photo on the flatbed scanner with the picture side down and the upper left corner of the photo in the upper left corner of the glass 2 Gently close the lid 3 Touch Start Copy Copy a book 1 Lift the lid and place the book on the flatbed scanner with the page that you want to copy at the upper left corner of the glass 2 Gently close the lid 3 Gently press down on the lid to press the book to the flatbed scanner surface 4 Touch Start Copy
302. the page from the MFP control panel memory cards or hard disks thatare 4 Touch File Directory installed in the device 5 Touch Print Fax reports 1 From the Home screen touch Administration Five reports show fax activity fax calls 2 Touch Information billing codes blocked fax numbers and speed dial numbers 3 Touch Fax Reports E NOTE Fax reports are 4 Touch one of the following buttons to print the corresponding report available only on device e Fax Activity Log models that have fax capabilities e Fax Call Report e Billing Codes Report e Blocked Fax List e Speed Dial List 5 Touch Print For more information see the fax guide that came with the device Font lists 1 From the Home screen touch Administration Shows which fonts are currently 2 Touch Information installed in the device 3 Touch Sample Pages Fonts 4 Touch either PCL Font List or PS Font List 5 Touch Print NOTE The font lists also show which fonts reside on a hard disk accessory or DIMM Information pages 183 Embedded Web server Use the embedded Web server to view MFP and network status and to manage printing functions from your computer instead of from the MFP control panel The following are examples of what you can do using the embedded Web server ET NOTE When the printer is directly connected to a computer use the HP Easy Printer Care software to view the printer status e View MFP status info
303. the printer and select Properties Click the Device Settings tab 2 3 4 Select Allow Manual Duplex 5 Select the appropriate size and type 6 OntheFinishing tab click Print on Both Sides or Print on Both Sides Manually 7 The default binding option is to bind on the long edge of the paper in portrait layout To change the setting click the Finishing tab and select the Flip pages up check box 8 Click OK The Print on Both Sides instructions appear Follow the instructions to finish printing your document ET NOTE Ifthe total number of sheets to be duplexed exceeds the tray 1 capacity for manual duplex jobs feed the top 100 sheets and press Menu When prompted feed the next 100 sheets and press Menu Repeat as necessary until all the sheets from the output stack have been loaded into tray 1 Layout options for printing on both sides The four duplex orientation options are shown here To select option 1 or 4 select Flip Pages Up in the printer driver 122 Chapter9 Print tasks ENWW 1 Long edge landscape Every other printed image is oriented upside down Facing pages are read continuously from top to bottom 2 Short edge landscape Every printed image is oriented right side up Facing pages are read from top to bottom 3 Long edge portrait This is the default setting and the most common layout used E
304. then click OK Click Upload to load the file 192 Chapter 14 Manage the MFP ENWW Update the firmware Update the printer firmware by loading the new firmware file from the computer You can find new firmware files for your printer at htto Awww hp com support licm4730mfp T 2 3 4 Open the HP Printer Utility In the Configuration Settings list select Firmware Update Click Choose navigate to the firmware file that you want to upload and then click OK Click Upload to load the firmware file Activate the two sided printing duplexing mode Turn on the two sided printing feature on printers equipped with automatic duplexers T 2 3 Open the HP Printer Utility In the Configuration Settings list select Duplex mode Select Enable Duplex Mode to activate the two sided printing mode and then click Apply Now Lock or unlock printer storage devices Manage access to printer storage devices from the computer 1 2 3 4 5 Open the HP Printer Utility In the Configuration Settings list select Lock Resources On the Control Panel Access Level pop up menu select the access level that you want to set for the printer control panel Select the devices that you want to lock and clear any devices that you want to unlock Click Apply Now Save or print stored jobs ENWW Turn on the printer job storing function or print a stored job from the computer You also can delete a stored print job 1
305. ting on labels Serious damage can result NOTE In the printer driver Print on Both Sides manually is available only when the duplex printing accessory does not support the type of print media being used Print tasks ENWW Enable or disable automatic two sided printing in the Windows printer driver 1 Insert enough paper into one of the trays to accommodate the print job CAUTION Do not load media that is heavier than 105 g m 28 Ib bond This can jam the MFP 2 Open the printer driver 3 On the Finishing tab click Print on Both Sides 4 Click OK Layout options for printing on both sides The following are the four duplex orientation options To select option 1 or 4 select Flip Pages Up in the printer driver 1 Long edge landscape This layout is often used in accounting data processing and spreadsheet programs Every other printed image is oriented upside down Facing pages are read continuously from top to bottom 2 Short edge landscape Each printed image is oriented right side up Facing pages are read from top to bottom on the left page and then from top to bottom on the right page 3 Long edge portrait This is the default setting and the most common layout used with every printed image oriented right side up Facing pages are read from top to bottom on the first page
306. tion If you have modified the device configuration since installation the driver can be automatically updated with the new configuration In the Properties dialog box see Open the printer drivers on the Device Settings tab select the Update Now option from the drop down box to update the driver ENWW Select the correct printer driver 65 Priority for print settings Changes to print settings are prioritized depending on where the changes are made ET NOTE The names of commands and dialog boxes might vary depending on your software program e Page Setup dialog box Click Page Setup or a similar command on the File menu of the program you are working in to open this dialog box Settings changed here override settings changed anywhere else e Printdialog box Click Print Print Setup or a similar command on the File menu of the program you are working in to open this dialog box Settings changed in the Print dialog box have a lower priority and do not override changes made in the Page Setup dialog box e Printer Properties dialog box printer driver Click Properties in the Print dialog box to open the printer driver Settings changed in the Printer Properties dialog box do not override settings anywhere else in the printing software e Default printer driver settings The default printer driver settings determine the settings used in all print jobs unless settings are changed in the Page Setup Print or Printer Properties dialo
307. tion To continue turn off then on The duplex printing accessory is not connected correctly to the MFP If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support licm4730mfp Calibrating The MFP is calibrating No action is necessary Check output device An error has occurred with the output device Remove and reinstall the output device Chosen personality not available To continue touch OK A print job requested a MFP language personality that is not available for this MFP The job will not print and will be cleared from memory Print the job by using a printer driver for a different printer language or add the requested language to the MFP if possible To see a list of available personalities print a configuration page See Information pages Close drawer below Tray 1 One or more of the drawers below tray 1 is open 1 Close the drawers below tray 1 2 Ifthe message persists contact HP Support at http www hp com support licm4730mfp Close right doors A door on the right side of the MFP is open 1 Close the door 2 Ifthe message persists contact HP Support at http www hp com support ljcm4730mfp Close small front door Digital Send Communication Error The small front door is open An error has occurred during a digital send task 1 Close the small front
308. tral grays 149 151 options 141 Pantone matching 145 printed vs monitor 145 printing colorsamples 146 printing in grayscale 147 150 sample book matching 145 sRGB 142 using 137 colorfade 271 272 color fade problem solving 271 272 Color tab settings 124 132 147 150 configuration page Information menu 18 printing 182 configurations models 2 connectivity auxiliary 80 network utilities 85 parallel 78 USB 79 connectivity features 7 contracts maintenance 309 control panel access denied 232 Administration menu 17 buttons 14 cleaning touchscreen 212 copy screen 154 E mail Setup menu 42 e mail screen 168 Fax Setup menu 39 help 16 Home screen 15 Information menu 18 Initial Setup menu 31 lights 14 locating 9 locking menus 198 Management menu 29 messages alphabetical list 226 messages numerical list 226 messages types of 225 Resets menu 54 Send Setup menu 42 Service menu 55 settings 66 Time Scheduling menu 27 touchscreen buttons 16 troubleshooting 224 controlling print jobs 100 Copitrak devices 196 copying books 162 canceling 164 collating 161 control panel navigation 154 error messages 238 features 6 153 Job Mode 163 multiple originals 163 photos 162 quality troubleshooting 263 speed specifications 5 two sided documents 158 cover pages 116 126 covers locating 9 crooked pages 282 custom paper sizes 91 custom size paper settings Macintosh 126 Windows 116 customer support embedded Web server
309. trol panel display Fewer than 20 staples remain in the staple cartridge Replace the staple cartridge The number of pages in the job exceeds the 30 page limit for stapling TOO MANY PAGES IN JOB TO STAPLE appears on the MFP control panel display For jobs that have more than 30 pages staple the pages manually Solid amber The accessory is experiencing a hardware malfunction 66 X X OUTPUT DEVICE FAILURE appears on the control panel display Blinking amber The accessory has a staple jam Stapler Jam appears on the control panel display The accessory has a paper jam or a sheet needs to be removed from the unit even if the sheet is not jammed 13 XX YY JAM IN TOP OUTPUT BIN appears on the control panel display The bin is full Stacker Bin Full appears on the control panel display The stapler is out of staples Replace Stapler Cartridge appears on the control panel display The jam access cover is open Output paper path open appears on the control panel display The stapler unit is open Output paper path open appears on the control panel display Make sure the staple cartridge cover is completely closed The firmware is corrupt Corrupt Firmware In External Accessory appears on the control panel display Off The MFP might be in sleep mode Press any button on the control panel The accessory is not receiving power Turn the MFP power off Check that the accessory is properly seated on and connected to the
310. ts during the warranty period HP will at its option either repair or replace products which prove to be defective Replacement products may be either new or equivalent in performance to new HP warrants to you that HP software will not fail to execute its programming instructions after the date of purchase for the period specified above due to defects in material and workmanship when properly installed and used If HP receives notice of such defects during the warranty period HP will replace software which does not execute its programming instructions due to such defects HP does not warrant that the operation of HP products will be uninterrupted or error free If HP is unable within a reasonable time to repair or replace any product to a condition as warranted you will be entitled to a refund of the purchase price upon prompt return of the product HP products may contain remanufactured parts equivalent to new in performance or may have been subject to incidental use Warranty does not apply to defects resulting from a improper or inadequate maintenance or calibration b software interfacing parts or supplies not supplied by HP c unauthorized modification or misuse d operation outside of the published environmental specifications for the product or e improper site preparation or maintenance TO THE EXTENT ALLOWED BY LOCAL LAW THE ABOVE WARRANTIES ARE EXCLUSIVE AND NO OTHER WARRANTY OR CONDITION WHETHER WRITTEN OR ORAL I
311. ts box type a name for the shortcut Click OK Use printing shortcuts 1 2 3 4 On the File menu in the software program click Print Select the driver and then click Properties or Preferences Select the shortcut that you want to use from the Printing Shortcuts box Click OK ET NOTE Touse printer driver default settings select Factory Default Set a custom paper size 1 2 3 4 5 6 T 8 On the File menu in the software program click Print Select the driver and then click Properties or Preferences On the Paper Quality tab click Custom On the Custom Paper Size window type the name of the custom paper size Type the paper size length and width If you type a size that is too small or too large the driver adjusts the size to the minimum or maximum size that is allowed If necessary click the button to change the unit of measure between millimeters and inches Click Save Click OK The name that you saved appears in the paper size list for future use Use different paper and print covers Follow these instructions for printing a first page that is different from other pages in the print job 3 2 On the File menu in the software program click Print Select the driver and then click Properties or Preferences 116 Chapter9 Print tasks ENWW 8 3 4 5 6 7 Click the Paper Quality tab In the Special pages list box click Print pages on different paper Click Settings
312. ts for UNIX HP UX Sun Solaris are available at http www hp com go unixmodelscripts Sample model scripts for Linux networks are available at http Ainuxprinting org ENWW UNIX 75 76 Chapter5 Software for other operating systems ENWW 6 Connectivity e Parallel connection e USB connection e Auxiliary connection e Network configuration e Network utilities ENWW TT Parallel connection Establish a parallel connection by connecting the MFP to the computer with a bidirectional parallel cable IEEE 1284C compliant that has a c connector The cable can be a maximum of 10 meters 30 feet long Figure 6 1 Parallel port connection 1 C connector 2 Parallel port ET NOTE To use the enhanced capabilities of the bidirectional parallel interface ensure that the most recent printer driver is installed Factory settings support automatic switching between the parallel port and one or more network connections on the MFP 78 Chapter6 Connectivity ENWW USB connection This MFP supports USB 2 0 device and host USB connections The USB ports are located on the back of the MFP You must use an A to B type USB cable that is no longer than 2 meters 6 56 feet Figure 6 2 USB connection 1 USB connector 2 USB port ENWW USB connection 79 Auxiliary connection This MFP supports an auxiliary connection for paper handling input devices The por
313. ts should be forwarded Software Information location HP Web Jetadmin See the HP Web Jetadmin Help system for details on alerts and how to set them up Embedded Web server See Embedded Web server for general information about the embedded Web server See the embedded Web server Help system for details on alerts and how to set them up Configure alerts 201 Upgrade the firmware The MFP has remote firmware update RFU capability Use the information in this section to upgrade the MFP firmware Determine the current firmware version 1 From the control panel Home screen scroll to and touch Administration 2 Touch Information 3 Touch Configuration status Pages 4 Touch Configuration status Pages 5 Touch Print The firmware datecode is listed on the Configuration page in the section called Device Information The firmware datecode has this format YYYYMMDD XX XXX X The first string of numbers is the date where YYYY represents the year MM represents the month and DD represents the date For example a firmware datecode of that begins with 20061125 represents November 25 2006 Download new firmware from the HP Web site To find the most recent firmware upgrade for the MFP go to http www hp com go cljcm4730mfp software This page provides instructions for downloading the new firmware version Transfer the new firmware to the MFP ET NOTE The MFP can receive an RFU file update when it is in a ready state
314. ts the job settings to factory or user defined default values Stop button Stops the active job While stopped the control panel shows the options for the stopped job for example if you press the Stop button while the device is processing a print job the control panel message prompts you to cancel or resume the print job Start button 14 Chapter2 Control panel Begins a copy job starts digital sending or continues a job that has been interrupted ENWW Home screen The home screen provides access to the device features and it indicates the current status of the device ET NOTE Depending on how the device has been configured the features that appear on the home Screen can vary 1 Features Depending on how the system administrator has configured the device the features that appear in this area can include any of the following items e Copy e Fax e E mail e Secondary E mail e Network Folder e Job Storage e Workflow e Supplies Status e Administration 2 Device status line The status line provides information about the overall device status Various buttons appear in this area depending on the current status For a description of each button that can appear in the status line see Buttons on the touchscreen 3 Copy count The copy count box indicates the number of copies that the device is set to make 4 Help button Touch the Help button to open the embedded help system
315. ts to help diagnose network hardware or TCP IP network connection problems Embedded tests help to identify whether a network fault is internal or external to the device Use an embedded test to check hardware and communication paths on the print server After you select and enable a test and set the execution time you must select Execute to initiate the test Depending on the execution time a selected test runs continuously until either the device is turned off or an error occurs and a diagnostic page is printed 34 Chapter 2 Control panel ENWW Table 2 11 Jetdirect menus continued Menu item Sub menu item Sub menu item Values and Description LAN HW Test CAUTION Running this embedded test will erase your TCP IP configuration This test performs an internal loopback test An internal loopback test will send and receive packets only on the internal network hardware There are no external transmissions on your network Select Yes to choose this test or No to not choose it HTTP Test This test checks operation of HTTP by retrieving predefined pages from the device and tests the embedded Web server Select Yes to choose this test or No to not choose it SNMP Test This test checks operation of SNMP communications by accessing predefined SNMP objects on the device Select Yes to choose this test or No to not choose it Data Path Test This test helps to identify data path and corrupti
316. ture to customize the sleep mode settings for this device Use Sleep Delay default Select Use Sleep Delay to set the device to enter sleep mode after the delay that is specified in the Time Scheduling menu Manage Supplies Replace Supplies Stop at low This menu sets the MFP behavior for when a print cartridge fuser kit or tranfer kit is low Choose Stop at low to stop printing when a supply reaches a low condition Choose Stop at out to allow the MFP to continue printing until a color print cartridge is empty Choose Override at out to allow printing to continue when a color print cartridge is out however a control panel warning will state that override is in use and that a color supply must be replaced Stop at out default Override at out Supply Low Order Threshold Select a value in the range Use this menu to carry out administrative supply management tasks such as changing the threshold when supplies should be ordered Color Supply Out Auto continue black This menu sets the MFP behavior when a color supply is empty When Auto continue black is selected the Stop MFP will continue printing using black toner only Restrict Color Use Color printing access This item allows the administrator to disable or restrict color printing To use the Color If Allowed setting set up user permissions and or application permissions in the embedded Web server HP Easy Printer Care or Web Jetadmin Enable C
317. tures 117 Reduce or enlarge a document 1 2 3 4 On the File menu in the software program click Print Select the driver and then click Properties or Preferences On the Effects tab next to of Actual Size type the percentage by which you want to reduce or enlarge your document You can also use the scroll bar to adjust the percentage Click OK Print a document onto a different paper size 1 2 3 4 5 6 On the File menu in the software program click Print Select the driver and then click Properties or Preferences On the Effects tab click Print Document On Select the paper size to print on To print the document without scaling it to fit make sure that the Scale to Fit option is not selected Click OK Print multiple pages on one sheet of paper in Windows You can print more than one page on a single sheet of paper 1 2 12 54 w ow On the File menu in the software program click Print Select the driver and then click Properties or Preferences Click the Finishing tab In the section for Document Options select the number of pages that you want to print on each sheet 1 2 4 6 9 or 16 If the number of pages is greater than 1 select the correct options for Print Page Borders and Page Order e If you need to change the page orientation click Portrait or Landscape Click OK The product is now set to print the numbe
318. turns two to eight cartridges 1 Package each HP LaserJet print cartridge in its original box and bag 2 Tape up to eight single boxes together using strapping or packaging tape up to 70 Ibs 3 Use a single pre paid shipping label OR 1 Use your own suitable box or request a free bulk collection box from the http www hp com recycle or 1 800 340 2445 holds up to eight HP LaserJet print cartridges 2 Use a single pre paid shipping label Single returns Shipping 1 Package the HP LaserJet print cartridge in its original bag and box 2 Place the shipping label on the front of the box For all HP LaserJet print cartridge recycling returns give the package to UPS during your next delivery or pickup or take it to an authorized UPS drop off center For the location of your local UPS drop off center call 1 800 PICKUPS or visit http www ups com If you are returning via USPS label give the package to a U S Postal Service carrier or drop off at a U S Postal Service Office For more information or to order additional labels or boxes for bulk returns visit http www hp com recycle or call 1 800 340 2445 Requested UPS pickup will be charged normal pickup rates Information subject to change without notice Non US returns Paper To participate in HP Planet Partners return and recycling program just follow the simple directions in the recycling guide found inside the packaging of your new printer supply item o
319. tus menu ssssseeee 99 Automatic media type sensing auto sense mode ssssssee 99 N CVAM ENIM 99 Tray 2 4 sensing idi deci eddie EE dete din da deae ELA ed add 100 Select the media by source type or size ssssssssssssseeeeeeneennns 100 SM R EPRS 100 Type and SZE eoii iN E EENEN EE AA 100 Select the Output DiMera a a aaa a aie aa aaia E aa aia 101 Standard OuUtpUt DINS mee 101 3 bin mailbox output bins sssssssssssssseeeeeeeer en nennen nennen enne tennen 101 Select an output locatiOl rete tet entente n dern ttes eaa dad 102 Configure the 3 bin mailbox sese 102 Configure the printer driver to recognize the 3 bin mailbox in WIFICIOWS iecit rere e he e e o ee re ee e avra Ree 102 Configure the printer driver to recognize the 3 bin mailbox in DUETe Dei MC 103 Select the 3 bin mailbox operating mode at the control panel 103 Select the 3 bin mailbox operating mode in the printer driver 103 Select the operating mode in the printer driver Mac OS X 104 8 Use product features eise sro E 106 Sleep and AUCI CH 106 Job storage feat res i ies di m dde tradi dri adeo ua dde e unde uu dde E Ld 107 Gain access to the job storage features ssssssssssss een 107 Use the proof and hold feature ccccccce
320. ud hotline Call the HP fraud hotline 1 877 219 3183 toll free in North America when you install an HP print cartridge and the MFP message says the cartridge is non HP HP will help determine if the product is genuine and take steps to resolve the problem The following issues are signs that your print cartridge might not be a genuine HP print cartridge e A high number of problems occur with the print cartridge e The cartridge does not look like it usually does for example the packaging differs from HP packaging Print cartridge storage Do not remove the print cartridge from its package until you are ready to use it CAUTION To prevent damage to the print cartridge do not expose it to light for more than a few minutes ENWW Manage supplies 207 Table 14 1 Print cartridge temperature specifications Environmental condition Recommended Allowed Storage standby Temperature print cartridge 17 to 25 C 62 6 to 77 F 15 to 30 C 59 to 86 F 20 to 40 C 4 to 104 F Print cartridge life expectancy The life of the print cartridge depends on usage patterns and the amount of toner that print jobs require HP print cartridges last an average of 12 000 pages when printing on letter or A4 size paper at 5 coverage for each print cartridge Usage conditions and print patterns may cause actual results to vary Check the print cartridge life You can check the print cartridge life on the MFP control panel in th
321. uires attention before it can continue Touch the error button to see a message that describes the error The message also has instructions for solving the problem Warning button The warning button appears when the device has a problem but can continue functioning Touch the warning button to see a message that describes the problem The message also has instructions for solving the problem Help button Touch the help button to open the built in online Help system For more information see Control panel help system Control panel help system The device has a built in Help system that explains how to use each screen To open the Help system touch the Help button 9 in the upper right corner of the screen For some screens the Help opens to a global menu where you can search for specific topics You can browse through the menu structure by touching the buttons in the menu For screens that contain settings for individual jobs the Help opens to a topic that explains the options for that screen If the device alerts you of an error or warning touch the error or warning button to open a message that describes the problem The message also contains instructions to help solve the problem 16 Chapter2 Control panel ENWW Navigate the Administration menu ENWW From the Home screen touch Administration to open the menu structure You might need to scroll to the bottom of the Home screen to see this feature
322. uke Rage 325 General telecom statement ccccccccetseedeccetteecceceeenseedsceeneaeecenceetanedeeeeeteeddeceeenaeececeeeneeces 326 Laser statement for Finland secreet et t xxt eet nuce ER Dex gerer Sex xb med una erias 327 Appendix E Install memory and print server cards Install memory and fonts c ctecect cet Eee nt dun eee sea ha E Eee E BARRE E ERE ERR REGE EXE E HER RHET ERRARE 330 Install DDR memory DIMMS sssssssee nmm emm nennen rrr enne 330 Install a flash memory Card idein dn tage din thee a nnd dua eda no dua dado eae 334 Enabling merory 2 2 2 eene e dade Seba de santana reb Le ERR REED ede 338 Enable memory for Windows 98 and Me ssssee 338 Enable memory for Windows 2000 and XP sssseeeeen 339 Install an HP Jetdirect or EIO print server card ssssssssssssssssssssseen eene 340 hue 343 ENWW xiii xiv ENWW 1 Product basics e Product comparison e Product features e Product walkaround ENWW Product comparison HP Color LaserJet CM4730 MFP The HP Color LaserJet CM4730 MFP is the base model and comes standard with the following items e 100 sheet multipurpose input tray tray 1 e Three 500 sheet input trays e Automatic document feeder ADF that holds up to 50 pages e HP Jetdirect embedded print server for connecting to a 10 100Base TX network e 256 megabytes MB of random access memory
323. ur color printing CMYK data files are typically used by and originate from graphic arts printing and publishing environments The MFP will accept CMYK colors through the PS printer driver The MFP color rendering of CMYK is designed to provide rich saturated colors for text and graphics ENWW Print in four colors CMYK 143 CMYK ink set emulation PostScript only The MFP color rendering of CMYK can be made to emulate several standard offset press ink sets In some situations the CMYK color values in an image or document might not be suited to the MFP For example a document might be optimized for another printer For best results the CMYK values should be adapted to the HP Color LaserJet CM4730 MFP Select the appropriate color input profile from the printer driver e Default CMYK HP CMYK technology produces optimal printing results for most printing jobs e Specification for Web Offset Publications SWOP Common ink standard in the United States and other countries regions e Euroscale Common ink standard in Europe and other countries regions e Dainippon Ink and Chemical DIC Common ink standard in Japan and other countries regions e Custom profile Select this option to use a custom input profile to accurately control color output for example to emulate another HP color LaserJet printer Color profiles can be downloaded from http www hp com 144 Chapter 10 Using color ENWW Color matching The process of match
324. urn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support licm4730mfp 56 X ERROR To continue turn off then on A temporary printing error has occurred Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support ljcm47S30mfp 57 XX ERROR To continue turn off then on A temporary printing error has occurred Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support ljcm47S30mfp 58 XX ERROR To continue turn off then on A temporary printing error has occurred Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support ljcm47 30mfp 59 XY ERROR To continue turn off then on A temporary printing error has occurred Turn the MFP off and then turn the MFP on 230 Chapter 16 Problem solving ENWW Table 16 1 Control panel messages continued Control panel message Description Recommended action If this message persists contact an HP authorized service or support provi
325. uthorized service or support provider See the HP support flyer or go to http www hp com support ljcm4730mfp 22 EMBEDDED I O BUFFER OVERFLOW To continue touch OK Too much data was sent to the embedded HP Jetdirect print server Touch OK to print the transferred data Some data might be lost 30 1 YY SCANNER FAILURE An error has occurred in the scanner Check the scanner lock Turn the MFP off and then on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support ljcm4730mfp 40 BAD EIO X TRANSMISSION To continue touch OK The connection between the MFP and the EIO card in the specified slot has been broken Touch OK to clear the error message and continue printing 40 BAD SERIAL TRANSMISSION To continue touch OK A serial data error parity framing or line overrun occurred as data was being sent by the computer Touch OK to clear the error message Data will be lost 40 EMBEDDED I O BAD TRANSMISSION To continue touch OK A temporary printing error has occurred Turn the MFP off and then turn the MFP on If this message persists contact an HP authorized service or support provider See the HP support flyer or go to http Awww hp com support licm4730mfp 41 3 LOAD TRAY XX lt TYPE gt lt SIZE gt This is typically caused if two or more sheets of media stick together in
326. utomatically deletes your previous proof and hold job 1 2 3 4 5 6 From the Home screen touch Job Storage Touch the Retrieve tab Scroll to and touch the job storage folder that holds the job Scroll to and touch the job that you want to delete Touch Delete Touch Yes 108 Chapter 8 Use product features ENWW Use the personal job feature Use the personal printing feature to specify that a job is not printed until you release it First set a 4 digit PIN by typing the PIN in the printer driver The PIN is sent to the device as part of the print job After you have sent the print job to the device you must use the PIN to print the job Create a personal job To specify that a job is personal in the driver select the Personal Job option type a user name and job name and then type a four digit PIN into the Make Job Private field The job will not print until you enter the PIN at the device control panel Print a personal job You can print a personal job at the control panel after the job has been sent to the device 1 2 3 4 oN So From the Home screen touch Job Storage Touch the Retrieve tab Scroll to and touch the job storage folder that holds the personal job Scroll to and touch the personal job that you want to print 2333 E NOTE A personal job will have a 5l lock symbol next to it Touch the PIN field Use the numeric keypad to type the PIN and then touch OK Touch the Copie
327. vailable in the HP LaserJet Analog Fax Accessory 300 User Guide An electronic version of this guide is located on the CD that comes with the HP Color LaserJet CM4730f MFP HP Color LaserJet CM4730fsk MFP and HP Color LaserJet CM4730fm MFP ENWW 311 Physical specifications Table C 1 Product dimensions Product Height Depth Width Weight HP Color LaserJet CM4730 MFP 1153 mm 639 mm 788 mm 31 inches 124 kg 273 Ib 45 4 inches 25 2 inches HP Color LaserJet CM4730f MFP 1153 mm 639 mm 788 mm 31 inches 124 kg 298 Ib 45 4 inches 25 2 inches HP Color LaserJet CM4730fsk MFP 1153 mm 639 mm 1106 mm 136 kg 298 Ib 45 4 inches 25 2 inches 43 5 inches HP Color LaserJet CM4730fm MFP 1153 mm 639 mm 1106 mm 136 kg 298 Ib 45 4 inches 25 2 inches 43 5 inches 1 Without print cartridge Table C 2 Product dimensions with all doors and trays fully opened Product Height Depth Width HP Color LaserJet CM4730 MFP 1580 mm 62 2 inches 980 mm 38 6 inches 1160 mm 45 7 inches HP Color LaserJet CM4730f MFP 1580 mm 62 2 inches 980 mm 38 6 inches 1160 mm 45 7 inches HP Color LaserJet CM4730fsk MFP 1580 mm 62 2 inches 980 mm 38 6 inches 1588 mm 62 5 inches HP Color LaserJet CM4730fm MFP 1580 mm 62 2 inches 980 mm 38 6 inches 1588 mm 62 5 inches 312 Appendix C MFP specifications ENWW Electrical specifications ENWW WARNING Power requirements are based on the country region where the
328. very printed image is oriented right side up Facing pages are read from top to bottom 4 Short edge portrait Every other printed image is oriented upside down Facing pages are read continuously from top to bottom Create booklets You can copy two pages on one sheet of paper so you can fold the pages in the center to form a booklet The device arranges the pages in the correct order For example if the original document has eight pages the device prints pages 1 and 8 on the same sheet 1 2 3 4 5 6 On the File menu in the software program click Print Select the driver and then click Properties or Preferences Click the Finishing tab Select Print On Both Sides In the drop down box for Booklet Layout select either Left Edge Binding or Right Edge Binding The Pages per Sheet setting automatically changes to 2 pages per sheet Click OK Set the stapling options Select the stapler in the printer driver T 2 ENWW Click Start point to Settings and then click Printers for Windows 2000 or Printers and Faxes for Windows XP and Vista Right click the HP product icon and then click Properties or Printer Preferences Windows printer driver features 123 3 Click the Device Settings tab 4 On the Output tab click the drop down list under Staple and click One edge Configure the printer driver to recognize the optional stapler stacker 1 Open the Printers folder 2 Select HP Color Lase
329. vice and support ENWW HP maintenance agreements HP has several types of maintenance agreements that meet a wide range of support needs Maintenance agreements are not part of the standard warranty Support services may vary by area Check with your local HP dealer to determine the services available to you On site service agreements To provide you with the level of support best suited to your needs HP has on site service agreements with three response times Priority onsite service This agreement provides 4 hour service response to your site for calls made during normal HP business hours Next day onsite service This agreement provides support by the next working day following a service request Extended coverage hours and extended travel beyond HP s designated service zones are available on most on site agreements for additional charges Weekly volume on site service This agreement provides scheduled weekly on site visits for organizations with many HP products This agreement is designated for sites using 25 or more workstation products including printers plotters computers and disk drives ENWW HP maintenance agreements 309 310 Appendix B Service and support ENWW C MFP specifications This section provides the following specifications e Physical specifications e Electrical specifications e X Acoustic specifications e X Environmental specifications Specifications for the Analog Fax Accessory are a
330. y or if you are experiencing a decrease in copy quality such as streaking Clean the ADF delivery system 1 Open the scanner lid 2 3 Clean the ADF backing by wiping them with a clean damp lint free cloth Use an ammonia based surface cleaner only when a water dampened cloth does not clean the ADF components 4 Clean the scanner glass by wiping it gently with a clean slightly damp lint free cloth Use an ammonia based surface cleaner only when a water dampened cloth does not clean the scanner glass ENWW Clean the MFP 213 5 Close the scanner lid Clean the ADF rollers You should clean the rollers in the ADF if you are experiencing misfeeds or if your originals show marks as they exit the ADF CAUTION Clean the rollers only if you experience misfeeds or marks on the originals and you notice dust on the rollers Cleaning the rollers frequently could introduce dust into the device 1 Open the scanner lid 214 Chapter 15 Maintenance ENWW 2 Locate the rollers near the white vinyl ADF backing 3 Wipe the rollers gently with a clean water dampened lint free cloth A CAUTION Do not pour water directly onto the rollers Doing so might damage the device 4 Close the scanner lid ENWW Clean the MFP 215 5 Pull the release lever to open the ADF cover 6 Locate the rollers 7 Wip
331. y to load fonts data device To continue touch OK The MFP does not have enough memory to load the data for example fonts or macros from the location specified Touch OK to continue without this information If the message persists add more memory JAM IN DOCUMENT FEEDER Media is jammed in the document feeder Remove jammed media from the document feeder Follow the instructions in the onscreen dialog box If the message persists after all jams have been cleared a sensor might be stuck or broken Contact an HP authorized service or support provider See the HP support flyer or go to http www hp com support ljcm4730mfp LDAP Server is not responding Contact administrator The LDAP server has exceeded the time out value for an address request Verify the LDAP server address Contact the network administrator Load Tray 1 type size The tray is empty or configured for a different size than the size requested Follow the instructions in the onscreen dialog box Manually feed type size The specified job requires manual feed from tray 1 Load the requested media into tray 1 To override the message touch OK to use a type and size of media that is available in another tray Network connection required for Digital Sending Contact administrator A digital sending feature has been configured but a network connection is not detected Verify the network connect
332. you type a character that does not match any entry in the list the auto complete text is removed from the display to indicate that you are typing an address that is not in the address book 170 Chapter 12 Scan and send to e mail ENWW Use the address book You can send e mail to a list of recipients by using the address book feature of the device See your system administrator for information about configuring address lists ET NOTE You can also use the embedded Web server EWS to create and manage the e mail address book The EWS e mail address book can be used to add edit or delete single e mail addresses or e mail distribution lists For more information see Embedded Web server Create a recipient list 1 From the Home screen touch E mail 2 Complete one of the following steps e Touch To to open the keyboard screen and then type the recipients e mail addresses Separate multiple e mail addresses with a semicolon or by touching Enter on the touchscreen e Use the address book a On the Send E mail screen touch the address book button to open the address book b Navigate the entries in the address book by using the scroll bar Hold down the arrow to scroll quickly through the list c Highlight the name to select a recipient and then touch the add button P You can also select a distribution list by touching the drop down list at the top of the screen and then touching All or add a recipient from a lo
333. ze and type of paper that you want to use for incoming faxes Output Bin lt Binname gt Select the default output bin if applicable to use for faxes ENWW Default Job Options menu 23 Default E mail Options Administration gt Default Job Options gt Default E mail Options Menu item Values Description Document File Type PDF default Select the file format for the e mail JPEG TIFF M TIFF Output Quality High large file Selecting higher quality for output increases the size of the output file Medium default Low small file Resolution 300 DPI Select the resolution Use a lower setting to create smaller files 200 DPI 150 DPI default 75 DPI Color Black Color scan default Specify whether the e mail will be in black or in color Black white scan TIFF Version TIFF 6 0 default Specify the TIFF version to use when saving scanned files TIFF Post 6 0 24 Chapter2 Control panel Default Send to Folder Options Administration gt Default Job Options gt Default Send To Folder Options Menu item Values Description Color Black Color scan Specify whether the file will be in black or in color Black white scan default Document File Type PDF default Select the file format for the file M TIFF TIFF JPEG TIFF version TIFF 6 0 default Specify the TIFF version to use when saving scanned files TIFF post 6 0 Output Quality High large file Selecting higher quality fo

HP Color LaserJet CM4730 MFP User Guide - ENWW

Contents

Download Pdf Manuals

Related Search

Related Contents