Network Intelligent Speed Dome User`s Manual
Contents
1. Internet R10 7 Figure 4 1 The login interface is shown as below See Figure 4 2 Please input your user name and password Default factory name is admin and password is admin Note For security reasons please modify your password after you first login 3 Http 7710 19 5 2437 Windows Internet Explorer Ele Edt View Favertes Tools Help AH Pa eres E B Address AE het 110 155 2469 WEB SERVICE Username admin Password Figure 4 2 If it is your first time to login in system pops up warning information to ask you whether install control webrec cab or not after you logged in for one minute Please click OK button system can automatically install the control When system is upgrading it can overwrite the previous Web too If you can t download the ActiveX file please check whether you have installed the plug in to disable the control download Or you can lower the IE security level See Figure 4 3 Internet Options PX Security Settings Internet Zone General Security Privacy Content Connections Programs Advanced Settings O Disable Select a zone to view or change security settings 10 Enable 9 Download signed ActiveX controls not secure a Y 3 O Disable Internet Local intranet Trusted sites Y Enable not secure lii gt Prompt recommended Internet 9 Download unsigned ActiveX controls not secure ew This zone is for Internet websi2. 23 6 FAQ 6 1 Daily Maintenance Please clean dome cover regularly to get vivid image Handle the cover with care Use water to wash Don t use cloth to clean Use mild detergent to clean if there is too much dust Note The sweat from your hand may erode plating surface your nail may scrape dome cover resulting in blur image 6 2 Problems and Solutions SYMPTOM CAUSE SOLUTION 1 No self diagnosis no video signal when I connect dome to power Red LED is not on Your power supplying does not apply to the power Or connection is too loose Power off or transformer problem Check power is connected or properly earthed Check power supply condition or check transformer Red LED light on the power board is on Power supplying is low Something wrong with power board Use multimeter to check dome load Please contact retailer to replace power board 2 No self diagnosis There is a noise Power supplying is inadequate Replace power supplying Mechanical malfunction Need electrical engineer help 3 Self diagnosis is ok No video signal Power connection is too loose connect tightly Check the circuit connection Video switch connection is wrong or improper operation Connect again Please refer to user s manual for cable connection information 4 Self diagnosis is o k but can not operate the dome Control
3. confirm button to go to the third submenu IDLE FUNCTION It is to set the idle movement and idle time Move the cursor to IDLE FUNCTION and then click confirm button to go to the third submenu PRIVACY MASK It is to set privacy mask number and etc Move the cursor to current item and then click confirm button to go to the third submenu NEXT PAGE It includes PTZ speed set zero power up menu idle PTZ auto stop and heater Move the cursor to the item and then click the confirm button to set Click the confirm button to view rest setting items BACK Go back to previous menu EXIT Log out system menu 5 4 4 1 Preset Setup PRESET NO 001 TITLE PRESETOO1 SETTING CALL BACK EXIT Move the cursor to PRESET button and then click confirm button to go to set interface PRESET NO Please use left right key to modify preset number Please use the left right button on the keyboard or in the speed dome terminal menu to set TITLE Title text is the label used for you to identify the camera System will automatically name a title for the camera SETTING Please input preset number first and then select the monitor zone Please move the cursor to setting and click confirm button The system will pop up a message PRESET Here means preset number And the SETTING column pops up an OK Now you successfully added a preset Please note you need to enable display preset title function first Main menu gt display setting gt p
4. PROGRAM START PROGRAM STOP RUN STOP BACK EXIT Pattern function can memory PTZ operation and camera focus zoom in and zoom out From the start position dome begins auto movement repeatedly This series IP dome supports maximum 5 patterns and one pattern can max support 400 commands Move the cursor to PATTERN and click confirm button PATTERN NO Here is to set pattern number Please click left right key to configure 20 e PROGRAM START Here is to memorize pattern starting point An icon OK pops up in screen to prompt you system begins memory pattern e PROGRAM STOP Here is to set pattern stop point After all the movement move the cursor to PROGRAM STOP and then click confirm button Now you have set one pattern System pops up an icon OK to prompt you system has memories one pattern e RUN Here is to activate pattern Input pattern number move the cursor to RUN and click confirm button system begins running pattern e STOP Here is to stop current pattern Input pattern number move the cursor to STOP and click confirm button System stops current pattern BACK Go back to previous menu EXIT Log out system menu Note e The dwell time between two orders should be less than one minute otherwise system will set to default value as one minute After click PROGRAM STOP do not click CALL button before icon disappears completely Any manual operation during the pattern procedure will termi
5. PTZ to the corresponding position and then click the confirm button to complete the setup e POWER UP It is to set the dome operation when the speed dome boots up The option includes none auto preset tour scan pattern Please move the PTZ to the corresponding position and then click the confirm button to complete the setup 22 e MENU IDLE If current setup is ON once you open the menu and leave it idle for specified period the menu may automatically disappear If current setup is OFF the menu is always there and will not disappear Please use the left right button to set There are several options Please move the PTZ to the corresponding position and then click the confirm button to complete the setup e PTZ AUTO STOP The speed dome will stop all the PTZ operations when there is no command for the specified time There are several options Please use the left right button on the keyboard or in the speed dome terminal menu to set e BACK Go back to the previous menu e EXIT Log out the system menu 5 5 Dome Abnormal Phenomenon Operation 5 5 1 Restore to Factory Default Setup From main menu SYSTEM INFORMATION move cursor to FACTORY DEFAULT and click confirm button Dome will reboot and all the setups restore to factory default setup 5 5 2 PTZ Movement is not smooth From menu to SYSTEM INFORMATION move cursor to RESTART and click confirm button This reboot will not modify all activated setup such as preset tour and pattern
6. ZOOM SPEED There are several options Please use the left right button on the keyboard or in the speed dome terminal menu to set e DIGITAL ZOOM There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set APERTURE It is a parameter to adjust the video whole definition and the sharpness of the edge The value ranges from 1 to 16 Please use the left right button on the keyboard or in the speed dome terminal menu to set NEXT PAGE It includes the following options picture flip freeze function stabilization camera factory default setup camera restart exit and back function setup Please use the left right button on the keyboard or in the speed dome terminal menu to set Click the OK button you can view the rest camera settings BACK Go back to previous menu EXIT Log out system menu 5 4 3 1 Exposure Setting AE MODE BLC ON OFF GAIN SETTING GAIN LIMIT 08 SHUTTER SLOW SHUTTER LIMIT 1 12 IRIS SETTING i NOISE REDUCTION 03 EXPOSURE COM 3D NOISE CONTROL ON OFF SLOW AE BACK SLOW SHUTTER EXIT WDR ENBALE NEXT PAGE BACK EXIT AE MODE Here you can set the camera exposure mode It includes auto manual AV iris priority TV shutter priority Please use the left right button on the keyboard or in the speed dome terminal menu to set o Auto It becomes valid after you set the exposure compensation backlight compensation BLC
7. series network intelligent speed dome product is an integrated high intelligent speed dome It adopts waterproof design and has small and delicate shape This is a digital and intelligent product of vivid video The installation is convenient These series product has simple internal design and the installation is quick and easy It supports various languages real time clock display and protocol auto recognition function It supports 360 continuously pan 92 tilt and 180 auto flip It can realize no blind spot monitor This series product can be widely used in remote monitor environments such as electric power customs water conservancy and banks 1 2 Features This series speed dome has the following features 1 2 1 On Screen Menu This series product menu supports multiple languages display and switch It is easy for you to view dome information and configure dome camera parameters 1 2 2 On screen Tips It is the screen operation prompt Here you can set call preset and display the preset number during the tour It can display preset title system software version speed dome position coordinates and etc 1 2 3 Support multiple protocols This series speed dome supports universally used protocols such as PELCO P and PELCO D You can use various devices such as matrix control keyboard and DVR and protocols to operate speed dome 1 2 4 Proportional Pan and Tilt This function keeps the image from moving too fast when there is a la
8. slow shutter wide dynamic region WDR o Manual It becomes valid after you set the gain setting shutter iris setting wide dynamic region WDR o AV It becomes valid after you set the exposure setting iris setting wide dynamic region WDR o TV It becomes valid after you set the shutter setting exposure compensation wide dynamic region WDR GAIN SETTING It is to adjust the gain There are several options Please use the left right button on the keyboard or in the speed dome terminal menu to set 15 e SHUTTER You can set shutter speed here There are several options Please use the left right button on the keyboard or in the speed dome terminal menu to set e IRIS SETTING It is to set iris There are several options Please use the left right button on the keyboard or in the speed dome terminal menu to set e EXPOSURE COM It is to set exposition mode There are several options Please use the left right button on the keyboard or in the speed dome terminal menu to set SLOW AE In the strong light environment you can lower the camera auto exposure speed to capture the image and suppress the high light There are several options The bigger the value is the exposure speed is slower and the speed is longer Please use the left right button on the keyboard or in the speed dome terminal menu to set e SLOW SHUTTER In lower illumination environment you can lower the cameras auto exposure time to capture the image and enhance
9. the definition The trail may occur if the object is moving Please use the left right button on the keyboard or in the speed dome terminal menu to set e WDR ENBALE It is an abbreviation for wide dynamic region Please make sure your camera supports current function This function can adjust the video brightness when the contrast between the strong light and the dark light is too high Please use the left right button on the keyboard or in the speed dome terminal menu to set NEXT PAGE It includes BLC GAIN LIMIT SLOW SHUTTER LOW LIMIT NOISE REDUCTION 3D NOISE REDUCTION and etc function setup Move the cursor to the item and then click the left right button to set o BLC Itis an abbreviation for back light compensation System can compensate the object in the dark light to achieve a clear video Please use the left right button on the keyboard or in the speed dome terminal menu to set o GAIN LIMIT It is to set the camera gain threshold Please use the left right button on the keyboard or in the speed dome terminal menu to set o SLOW SHUTTER LIMIT It is to set the low limit of the camera slow shutter It may affect the real time feature of the video if the shutter time is too long Please use the left right button on the keyboard or in the speed dome terminal menu to set o NOISE REDUCTION There may be noise when the camera is monitoring the low illumination environments You can use the digital filter to process the noise to guarante
10. to go to the third submenu ADDR INFORMATION Move the cursor to SITE INFORMATION and then click confirm button to go to the third submenu e SET NORTH DIRECTION Set dome benchmark direction so that you can know the angel between the benchmark and then current location Please move the cursor to the option and then click confirm button until you see O K Now you have set north direction LANGUAGE The dome menu language FACTORY DEFAULT Restore dome factory default setup Please move the cursor to the option and then click confirm button until you see O K Now you can see the IP dome begin rebooting to restore factory default setup RESTART Reboot the speed dome BACK Go back to the previous menu EXIT Log out system menu 5 4 1 1 Initialization information ADDR 001 H BAUD RATE 9600 PARITY NONE SOFTWARE V1 00 0 RHAGAD BACK EXIT Move the cursor to INITIAL INFORMATION and then click confirm button you can see the above interface Here you can view dome basic information 5 4 1 2 Address Information ADDRTYPE SOFT ADDR SOFT 001 BACK EXIT Move the cursor to SITE INFORMATION and then click confirm button You can refer to the Web operation manual in the resources CD for detailed information ADDR TYPE This series product uses the soft address 13 ADDR SOFT You can set address via software It is to say you can use menu to modify dome address The value ranges from 0 to
11. 1 10 15 5 8T 280 9202 a9ff eTG bTa2 B4 Tip You can click login button directly and then input corresponding information to login All Upgrade 255 0 0 255 0 0 255 255 0 255 0 0 255 0 0 Refresh Figure 3 1 22 Configlool Device List Select one IP address and then right click mouse you can see an interface is shown as in Figure 3 2 SN IP Address Port Subnet Mask Default Gateway Mac Address 1 10 15 5 111 STTTT 255 255 0 0 10 15 0 1 90 dT eb c3 12 10 15 5 84 40002 255 255 0 0 10 15 0 1 52 54 4c fa 3 10 15 5 82 40003 255 255 0 0 10 15 0 1 90 02 29 la 10 15 5 88 40007 255 255 0 0 10 15 0 1 52 54 4c E 10 15 5 254 40008 255 255 0 0 10 15 0 1 90 02 a9 16 2001 250 3000 1 1 2 112 40006 2001 250 300 90 02 99 e80 9202 a9 e04 7021 84 40006 e80 90 02 a9 8 10 15 5 186 3TTTT 255 255 0 0 90 02 a9 E 10 15 6 137 3TTTT 255 255 0 0 52 54 4c 10 10 15 5 139 3TTTT 255 255 0 0 a8 11 e80 9202 a9 eT8 flaf 64 37777 112 e80 9202 a9 e00 T3 a 64 3TTTT TI 14 2008 6 112 15 fe80 9202 a9 e08 16 10 15 5 149 3TTTT 117 e80 9202 a9 fe0T dc5 64 3TTTT 18 10 15 5 135 3TTTT 19 192 168 1 17 3TTTT 20 10 15 5 81 40000 21 10 15 5 87 40003 22 080 9202 a9 fe78 b7a2 64 40003 Tip You can click login button directly and then input correspo
12. 2 Day Night Mode B W amp Color Mode System can automatically switch to black and white mode in low illumination 1 2 13 Auto Focus Auto focus allows the lens to remain in focus during zoom in zoom out and motion functions to get vivid image 1 2 14 Backlight Compensation Balance the brightest and darkest sections of a scene to produce a more vivid picture 1 2 15 3D Intelligent Location Working with DVR just click part of the current scene will be displayed in the central window and automatically zooms All of these allow you to trace precisely 1 2 16 Idle Status When there is no available order you can use menu to set dome idle status after specified duration The idle status includes turn to specified preset or go to scan tour or pattern function 1 2 17 Power up The speed dome executes the power up operation after it rebooted and completed the initialization The power up function includes auto preset scan tour pattern and none 1 2 18 Image Flip You can enable image flip in the menu The flip function allows you to view continuous video 2 Cable Connection 2 1 Combination Cable Connection The combination cable includes the network cable audio video cable RS485 cable and alarm input output cable Please refer to the labels on the cable for detailed information Please refer to the following sheet for RS485 audio video port power port and network port information Name Function POWER e Power port Con
13. 255 Please use the left right button on the keyboard or in the speed dome terminal menu to set BACK Go back to the previous menu EXIT Log out system menu 5 4 2 Display Setting PRESET TITLE AZIMUTH DISP POSITION ZOOM DISP INSIDE TEMP TITLE DISP BACK EXIT Move the cursor to DISPLAY SETUP and then click confirm button you can go to the third submenu Please use the left right button on the keyboard or in the speed dome terminal menu to set After completed setup please click save button to save current setup PRESET TITLE Display dome preset title or not Please use the left right button on the keyboard or in the speed dome terminal menu to set You can go to Function Setup gt Preset section to set corresponding preset value and preset title AZIMUTH DISP Display dome current coordinates or not Please use the left right button on the keyboard or in the speed dome terminal menu to set POSITION Display the angel between the benchmark and then current location Please use the left right button on the keyboard or in the speed dome terminal menu to set ZOOM DISP Display speed dome zoom speed or not Please use the left right button on the keyboard or in the speed dome terminal menu to set INSIDE TEMPERATURE Display dome internal temperature or not There are three options C F Off Please use the left right button on the keyboard or in the speed dome terminal menu to set TITLE DISPLAY Here you can set to display the
14. Network Intelligent Speed Dome User s Manual Version 1 1 0 Table of Contents 1 FEATURES AND FUNCTIONS iat einander nennen ties 1 1 1 General altere e o DERIT REED 1 2 aisi IN CRT ETATE 12277 OneScreenm Men ttem ttem nimi etaim dti deberi 1 2223 Oncscreen TIPS muta RR UR o RR e DARE ON SUN I Id TE ote dad 1 2 3 Support multiple protocols Wicca ii eit Andi end ei ii teu de 1 2 4 Proportional Pan and Tilt cete emet ere c e rae ie R 1 2 5 Preset Setup and Recall sse eene nre nne nenne eren teen enne nenne nennen nnne 1 2 6 AUTO S Can sun aii ive di ete ee pie et a eite i mdi pie TAE Auto TOUR 1 2 8 Auto Pattern eee rov di 1 2 92 Privacy M sking 34 2 38 34485838 228 engem paene em RD Reb 1 2 10 AO li ia 1 2 11 Self diagnosls 5 5 ESPERSEN Biss un si ii ERE D IRURE RU ie ias 1 2 12 Day Night Mode B W amp Color Mode enne 1 2 13 AUTO ROCA Matera UCM e el Lt N E 2 1 2 14 Backlight Compensatii skro orrena eaea en ieia eaaa Era anno nennen nennen ENEE NEAR 2 1 2 15 3D Intelligent A NO 2 1 2 16 Idle Status ee Reb nuUa NU a RII P d eani 2 1 2 17 A bd tb tei Memes eiut ameet apte De oor ebd inus 2 1 2 18 Image ul 2 2 CABLE CONNECTION naar eof hau mE ku ro ug aS EEE uU GE CHAR AIR Cu CLA RUE 3 2 1 Combination Cable COnMeCtion svccsscisicssiisscccsecsscsseisecesceousnconscbeosuss oust ine eee aee soucossusuvscb pe UN
15. RE SETTING DAY NIGHT SETTING S MODE DIGITAL ZOOM APERTURE FUNCTION SETTING NEXT PAGE AUTO SCAN AUTO CRUISE AUTO PATTERN IDLE FUNCTION PRIVACY MASK NEXT PAGE 11 The above diagram illustrates the overall structure of the speed dome setup menu Note e ERR means current setup is invalid Please make sure all the cable connections are right 5 2 Self diagnosis System Information ADDR 001 8 BAUD RATE 9600 PARITY NONE SOFTWARE V1 00 0 BACK EXIT After installation please connect speed dome to power The system goes on a self diagnosis and then it pops up the above interface to show the system information If there is anything wrong during the self diagnosis system pops up error code The above interface disappears after speed dome received the first command or the display time lasts for 40 seconds ADDR Here you can view dome address information For example 001 S 1 is the address number S is software address mode Baud rate Dome communication baud rate Parity Communication parity bit format e Software Dome PTZ software version When you are using the control keyboard or the matrix host to control the device please make sure the control parameter of the keyboard or the matrix host is the same with the speed dome OSD including address baud rate parity Please make sure the cable connection is OK 5 3 Main Menu You can open the IP dome menu via control keyboard matrix
16. S EBEN SER ENTE EUR derne 3 2 2 SAA nennen ernennen wann enden EA S een een 3 2 3 Alarmi CONNECTION RN 4 3 QUICK CONFIGURATION TOOL ne la 5 3 1 iyu DEP 5 3 2 Blei pee P a 5 4 WEB OPERATION e n 8 4 1 NENA A E ee aduer ey ete te bee ee easet MP vete ie eO Eee en ved en voee toI SSR EST Red 8 4 2 Login ANGILOGOUE ii STE 8 A P 11 5 1 Screen Menu INdeX ico Er 11 5 2 Self diagnosis System Information sessesesueseenenneneonennensonenneneonenneneonennensonennenesnennensnnennsnssnennesssnennssnsnennns 12 5 3 A O TO 12 5 4 LE RT AAA 12 9 4 17 System Information scan i as 13 5 4 2 Display Setting ERROR 14 543 E NN 14 5 4 4 Function Setting A A 17 5 5 Dome Abnormal Phenomenon Operation sesessesseseonennenesnennenesnennenesnennunssnennsnssnennsnesnennenesnennsnssnene 23 5 5 1 Restore to Factory Default Setup sse enne enne nre nennen nennen enne nen 23 ii AM c 24 6 1 SA eslestengendstsesenssnhensisntenheersntenednatherkekesshes terkeeeken 24 6 2 Problems and SOLUTIONS ORCCOERPO UC e sas eie 24 7 APPENDIX THUNDER PROOF AND SURGE PROTECTION 25 8 APPENDIX TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS 26 111 Welcom
17. SE SETTING Move the cursor to cruise setting item and then click confirm button You can see the following interface Here you can add or remove the preset and set the corresponding dwell time and call speed One cruise can max include 32 presets The preset value ranges from 1 to 255 NO PRESET DWELL SPEED 01 000 005 013 02 000 005 013 03 000 005 013 32 000 005 013 B DWELL Here is t set dwell time The value ranges from 3s to 255s Please use the left right button on the keyboard or in the speed dome terminal menu to set B SPEED The speed value ranges from 1 to 16 When you move the cursor to one cruise number you can use left right button to turn the page When you move the cursor to one cruise number please click confirm button to set the cruise Please use up down button to set preset number dwell time and speed Use the left right button to go to the next cruise Click confirm button you can exit the setup After you completed the setup move the cursor to back button to go to the previous interface e DELETE CRUISE Here is to delete a cruise Input cruise number in CRUISE NO and then move the cursor to DELETE cruise click confirm button to delete CALL Here is to activate cruise Input touring number in touring NO and highlight CALL click confirm button to activate touring e STOP Here is to terminate touring BACK Go back to previous menu EXIT Log out system menu 5 4 4 5 Pattern PATTERN NO 001
18. ce Please make sure the CCD CMOS component is out of the radiation of the laser beam device Otherwise it may result in CCD CMOS optical component damage Daily Maintenance Current series product has no power button Please unplug all corresponding power cables before your begin installation or daily maintenance work Please keep the dustproof cap back to protect the CCD or CMOS part if the device does not work for a long time Do not touch CCD CMOS component You can use the blower to clean the dust on the surface of the device You can use the dry cloth with some alcohol or mild detergent to clear if necessary Do not use the volatility solvent such as the benzene or thinner or detergent with strong abradibility It may result in lens damage or it may adversely affect the device performance V f there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device 6 About Accessories Always use all the accessories recommended by manufacturer Before installation please open the package and check that all the components are included in the package Contact you local retailer ASAP if something is missing in your package 7 IE Version Usually we recommend IE 7 or higher version For those versions below IE 7 it may not support the operation of some functions vi 1 Features and Functions 1 1 General Introduction This
19. circuit is not properly connected check control cable connection Dome address protocol or baud rate setup is not right Please refer to user s manual for detailed information 5 Video signal loss occurs in high speed rotation 6 Video signal is not successive 7 Video is not clear Power supplying is not sufficient Circuit connection is too loose Replace power supplying Connect tightly Video switch or power problem Focus is in manual mode Need electrical engineer help Control manually Dome cover is dirty Wash dome cover 8 During camera switch there is a tilt movement in the monitor Camera power is not in the same Phase When several domes are connected to one transformer please connect the transformer output cable to the domes same side 24 7 Appendix Thunder Proof and Surge Protection This series speed dome adopts TVS lighting protection technology It can effectively prevent damages from various pulse signals below 1500W such as sudden lighting and surge While maintaining your local electrical safety code you still need to take necessary precaution measures when installing the speed dome in the outdoor environment e The distance between the signal transmission cable and high voltage device or high voltage cable shall be at least 50 meters Outdoor cable layout shall go under the penthouse if possible e For vast land please use seali
20. e Thank you for purchasing our product This user s manual is designed to be a reference tool for the operation of your system Here you can find information about this speed dome features and functions as well as a detailed menu tree Please keep it well for future reference Before installation and operation please read the following safeguards and warnings carefully iv Important Safeguards and Warnings em Electrical safety All installation and operation here should conform to your local electrical safety codes We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any problems caused by unauthorized modification or attempted repair Transportation Security No heavy stress violent vibration or water splash are allowed during transportation storage and installation Please use the original packing material or the material of the same quality when you ship it back to the manufacturer Installation Do not apply power to the product before completing installation Do not put object on the product Environment This series product should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc Please keep it away from the electromagnetic radiation object and environment Please keep the sound ventilation Do not allow the water and other liquid falling into the devi
21. e the clear video o 3D NOISE REDUCTION There may be noise when the camera is monitoring the low illumination environments The parameter here is to control the noise but it may affect the real time feature of the video BACK Go back to previous menu EXIT Log out system menu 5 4 3 2 Day Night Setting Move the cursor to DAY NIGHT SETTING and then click confirm button you can go to the submenu DAY NIGHT SENSITIVITY SAVE BACK EXIT DAY NIGHT It is to set day night switch mode There is several options Please use the left right button on the keyboard or in the speed dome terminal menu to set 16 SENSITIVITY It is the threshold value when the system switches from the black and white to the color in the auto mode BACK Go back to previous menu EXIT Log out system menu 5 4 3 3 Next Page Move the cursor to NEXT PAGE and then click confirm button you can go to the submenu PICTURE FLIP FREEZE FUNCTION FOCUS SENSITIVITY STABALIZATION ON CAMERA FACTORY DEFAULT CAMERA RESTATRT BACK EXIT PICTURE FLIP This function allows you to turn the image rotation 180 degrees There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set FREEZE FUNCTION This function allows the system from one preset to another preset without showing the video during the PTZ movement There are two options on off Please use the left right button on the k
22. eyboard or in the speed dome terminal menu to set FOCUS SENSITIVITY It is to set focus sensitivity STABALIZATION It is to effectively remove the effect of the slight vibration on the video Please use the left right button on the keyboard or in the speed dome terminal menu to set CAMERA FACTORY DEFAULT SETTING Move the cursor to current item and then click confirm button to restore factory default setup CAMERE RESTART Move the cursor to current item and then click confirm button to reboot the camera BACK Go back to previous menu EXIT Log out system menu 5 4 4 Function Setting PRESET PAN AUTO SCAN AUTO CRUISE AUTO PATTERN IDLE FUNCTION PRIVACY MASK NEXT PAGE BACK EXIT Please go back to main menu and move the cursor to FUNCTION SETTING click confirm button You can see the above interface PRESET Move the cursor to PRESET and then click confirm button to go to the third submenu PAN It is to set the speed dome rotation speed Move the cursor to PAN and then click confirm button to go to the third submenu 17 AUTO SCAN It is to set the speed dome scan number and scan speed Move the cursor to SCAN and then click confirm button to go to the third submenu AUTO CRUISE It is to set the cruise tour number and task Move the cursor to AUTO CRUISE and then click confirm button to go to the third submenu AUTO PATTERN It is to set the pattern number and etc Move the cursor to PATTERN and then click
23. k confirm button The dome begins 360 degrees continuous rotation e STOP Highlight stop item and then click confirm button The dome stops rotation BACK Go back to previous menu EXIT Log out system menu 5 4 4 3 Scan SCAN NO 001 SET LEFT LIMIT SET RIGHT LIMIT SCAN SPEED 160 RUN STOP BACK EXIT Move the cursor to SCAN button and then click confirm button SCAN NO Here is to set auto scan number Please use the left right button on the keyboard or in the speed dome terminal menu to set e SET LEFT LIMIT Here is to set camera left address Click confirm button to save current setup SET RIGHT LIMIT Here is to set camera right address Click confirm button to save current setup e SCAN SPEED It is to set scan speed Please use the left right button on the keyboard or in the speed dome terminal menu to set RUN Please input auto scan number first and then please move the cursor to RUN and click confirm button to activate auto scan function e STOP Here is to terminate auto scan function BACK Go back to previous menu EXIT Log out system menu 5 4 4 4 Cruise Touring CRUISE NO 001 CRUISE SETTING DELETE CRUISE RUN STOP BACK EXIT Move the cursor to highlight CRUISE item and then click confirm button to go to set interface CRUISE NO Here is to ser tour number Please use the left right button on the keyboard or in the speed dome terminal menu to set CRUI
24. nate current dome pattern operation 5 4 4 6 Idle Function IDLE FUNC OFF IDLE TIME 010MIN IDLE ACTION PRESET PRESET NO 001 AUTO SCAN NO 001 CRUISE NO 001 PATTERN NO 001 SAVE BACK EXIT When there is no available command for specified time dome automatically goes on the previous set functions e IDLE FUNCTION There are two modes ON OFF Please use left right key to set e IDLE TIME System idle period Please use the left right button on the keyboard or in the speed dome terminal menu to set e IDLE ACTION There are several functions you can select NONE PRESET SCAN TOURING PATTERN Please use the left right button on the keyboard or in the speed dome terminal menu to set e PRESET NO Here is for you to set preset number The value ranges from 1 to 255 System goes to specified preset when idle status is on e AUTO SCAN NO The value ranges from 1 to 5 Please use the left right button on the keyboard or in the speed dome terminal menu to set System begins specified scan when idle status is on e CRUISE NO The value ranges from 1 to 8 Please use the left right button on the keyboard or in the speed dome terminal menu to set System begins specified touring when idle status is on 21 e PATTERN NO The value ranges from 1 to 5 Please use the left right button on the keyboard or in the speed dome terminal menu to set System begins specified pattern when idle status is on e SAVE Move the cursor to SAVE a
25. nd click confirm button to save current setup e BACK Go back to previous menu e EXIT Log out system menu Privacy Mask PRIVACY NO ACTIVATE RESIZE DELETE SAVE BACK EXIT PRIVACY NO Here is to set privacy mask zones Please use the left right button on the keyboard or in the speed dome terminal menu to set ACTIVATE There are two settings on and off Please use the left right button on the keyboard or in the speed dome terminal menu to set when it is in the privacy mask area RESIZE It is to adjust the privacy zone size Move the cursor to current item and use the left right button on the keyboard or in the speed dome terminal menu to set Please continue pressing direction button to widen or narrow zone size is to narrow the horizontal width and is to widen the horizontal width is to widen vertical height and is to narrow the vertical height SAVE Here is to save user setup DELETE Here is to delete setup and restore default setting BACK Go back to previous menu EXIT Log out system menu 5 4 4 7 Next Page Move the cursor to the NEXT PAGE and then click the confirm button you can go to the third menu to set PTZ SPEED SET ZERO POWER UP MENU IDLE 1M PTZ AUTO STOP 158 SAVE BACK EXIT e PTZ SPEED It is to set PTZ speed Please use the left right button on the keyboard or in the speed dome terminal menu to set e SET ZERO It is to set the PTZ initial position Please move the
26. nding information to login Au Upgrade 255 255 0 0 255 255 0 0 255 255 255 0 192 168 2 255 255 0 0 10 15 0 eb 255 255 0 0 10 15 0 90 02 9 280 90 02 a9 78 BT a2 Refresh Login Logout Figure 3 2 Select the Open Device Web item you can go to the corresponding web login interface See Figure 3 3 A WEB SERVICE Windows Internet Explorer Eile Edit Vw Favorites Tools Help Qe gt x g amp seach feros amp GQ Em LJA Address 48 http 192 168 1 108 WEB SERVICE Username Password Figure 3 3 If you want to modify the device IP address without logging in the device web interface you can go to the configuration tool main interface to set In the configuration tool search interface Figure 3 1 please select a device IP address and then double click it to open the login interface Or you can select an IP address and then click the Login button to go to the login interface See Figure 3 4 In Figure 3 4 you can view device IP address user name password and port Please modify the corresponding information to login Please note the port information here shall be identical with the port value you set in TCP port in Web Network interface Otherwise you can not login the device If you are use device background upgrade port 3800 to login other setups are all invalid IP Address 192 168 1 10 User Name aee Password Port 37777 coa Figure 3 4 Afte
27. nect to the power cable GND e GND port 485A RS485 remote control 485B OUT Audio output AUDIO GND GND port IN Audio input GND Video GND Video Video output out OUT You can connect cable to this port if you want to use the analog video output LAN Network port Connect to the network cable Please refer to the following sheet for alarm input and output information Please note the IE6 does not support alarm upload function Please use IE7 or higher version e If it is your first time to boot up the WEB on the Windows 7 OS please right click the Internet Explorer icon on the desktop and then select Run as Administrator Name Function ALARM 1 2 i IN e Two alarm input channels They are to receive relay signal from the external alarm source You can go to dome menu to activate specified preset or patter e When the activation mode is NO normal open dome alarms when there is low voltage High voltage will not activate the alarm e When the activation mode is NC normal close dome alarms when there is high voltage Low voltage will not activate the alarm Note e Dome alarm input message is ground mode Dome alarm input signal are two modes normal open and normal close GND Alarm input ground end One channel alarm output channel When there is an alarm from OUT 4 current channel system activates relay or not UT Alarm output relay default setup i
28. ng steel tube under the land to implement cable layout and connects one point to the earth Open floor cable layout is forbidden e In area of strong thunderstorm hit or near high sensitive voltage such as near high voltage transformer substation you need to install additional high power thunder protection device or lightning rod e The thunder protection and earth of the outdoor device and cable shall be considered in the building whole thunder protection and conform to your local national or industry standard System shall adopt equal potential wiring The earth device shall meet anti jamming and at the same time conforms to your local electrical safety code The earth device shall not short circuit to N neutral line of high voltage power grid or mixed with other wires When connect the system to the earth alone the earth resistance shall not be more than 42 and earth cable cross sectional area shall below 25 mm2 See Figure 7 1 Video Lighting Rod Communication __ Liqhting Rod Power Xs xa Lighting Rod The speed dome shall be installed within the 45 angel of the lighting rod Earth cable resistance shall be less than 40 Steel tube shield Figure 7 1 25 8 Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Pb Hg Cd Cr VI PBB PBDE Sheet Metal o o o o o o Plastic Parts o o o o
29. o o PCB o o o o o 3 Housing O O O O O O Camera Driver o o o o o o Bearing O O O O O 3 Connection T o o 5 Cable Motor o o O o O O If possible Power 3 3 A M o o If possible Bracket 3 o A A 4 If possible Accessories o o o o o o Note O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T11363 2006 standard Note e This manual is for reference only Slight difference may be found in the user interface e All the designs and software here are subject to change without prior written notice e All trademarks and registered trademarks are the properties of their respective owners e If there is any uncertainty or controversy please refer to the final explanation of us e Please visit our website or contact your local service engineer for more information 26
30. or speed dome control terminal SYSTEM INFORMATION DISPLAY SETTING CAMERA SETTING FUNCTION SETTING EXIT e SYSTEM INFORMATION Dome self diagnosis information address information set north direction language factory default setup reboot and so on DISPLAY INFORMATION Display dome preset title azimuth display direction and etc CAMERA PARAMETERS Set camera white balance setup camera exposure setup day night setup focus setup and etc e FUNCTION SETTING Set preset pan auto scan auto cruise auto pattern idle motion and etc e EXIT Log out the system menu 5 4 Menu Operation 12 In the speed dome main menu you can use the left right button on the keyboard or in the speed dome terminal menu to configure the system menu Before setup please move the cursor to the current item you want to configure e In main menu please click confirm button to go to the sub menu or use left right key to configure setup Use up down button to select back option and then click confirm button to go back to the previous menu Use up down button to select exit option and then click confirm button to log out system menu All setup here will not lose when encounter power failure 5 4 1 System Information INITIAL INFORMATION ADDR INFORMATION SET NORTH LANGUAGE ENGLISH FACTORY DEFAULT RESTART BACK EXIT INITIAL INFORMATION Move the cursor to INITIAL INFORMATION and then click confirm button
31. r you logged in the configuration tool main interface is shown as below See Figure 3 5 2 ConfigTool NetWork Paraneter PPPOE System Informati onl System Upgrade General Parameter DHCP Enable fee IP Address AC Subnet Mask 255 255 255 0 Gateway FE Mac Address p0 02 a9 08 74 94 0 Figure 3 5 For detailed information and operation instruction of the quick configuration tool please refer to the Quick Configuration Tool User s Manual included in the resources CD 4 Web Operation This series speed dome product supports the Web access and management via PC Web includes several modules live view PTZ set alarm logout and etc 4 1 Network Connection Please follow the steps listed below for network connection e Make sure the speed dome has connected to the network properly Speed dome IP address and PC IP address shall be in the same network segment Speed dome default IP address is 192 168 1 108 If there is router please set the corresponding gateway and subnet mask Use order ping speed dome address to check connection is OK or not 4 2 Login and Logout Open IE and input speed dome address in the address bar For example if your camera IP is 192 168 1 108 then please input http 192 168 1 108 in IE address bar See Figure 4 1 Blank Page Windows Internet Explorer aboutiblank E gt r de blarkPage Input your IP IT address here
32. reset title Repeat the above procedures to set more presets Once you want to modify a preset you can input the preset number you want to modify and then follow the above steps to set the preset You can successfully modify a preset content CALL Here is to recall preset Move the cursor to PRESET NO and then input corresponding preset value Then move the cursor to CALL and then click confirm button to go to a preset BACK Go back to previous menu EXIT Log out system menu For PELCO protocol user please refer to the following special functions Call preset Call preset 28 or preset 95 to go to dome menu Call preset 29 or preset 99 to go to scan Call preset 24 or preset 81 to go to pattern Call preset 25 or preset 82 to go to cruise tour Call preset 30 or preset 96 to stop scan or pattern Call preset 31 or preset 83 to begin rotation Call preset 33 to enable PTZ 180 degrees rotation Call preset 34 to set dome position as 0 18 Set preset Set preset 26 or 92 to set scan left limit Set preset 27 or 93 to set scan right limit Set preset 22 or 79 to begin record Set preset 23 or 80 to stop record 5 4 4 2 Pan PAN SPEED 160 RUN STOP BACK EXIT Move the cursor to PAN button and then click confirm button to go to setup interface PAN SPEED Set dome rotation speed Please use the left right button on the keyboard or in the speed dome terminal menu to set RUN Move the cursor to call item and then clic
33. rge amount of zoom Speed dome continually decreases or increases pan and tilt speeds in proportion to depth of zoom When zooms speed is increasing the camera moving speed becomes slow When zooms speed is decreasing the camera moving speed becomes fast 1 2 5 Preset Setup and Recall Preset function is to save the address information such as PTZ pan tilt focus and etc to the memory so that you can quickly adjust the dome and PTZ to the correct position 1 2 6 Auto Scan Camera scans back and forth regularly in a horizontal field Here you need to set left and right limit and scan speed 1 2 7 Auto Touring Add addresses into a routine in a desired order and then set time and stop duration for each address The dome will begin an auto touring between these addresses 1 2 8 Auto Pattern Memorize dome operation such as pan tilt and zoom to repeat You can call it to repeat the previous operation 1 2 9 Privacy Masking Privacy masking is a user defined four sided area that can not be viewed by you The masking area will move with pan and tilt functions and automatically adjust in size as the lens zooms 1 2 10 Auto Flip The dome rotates 180 degrees and repositions itself for uninterrupted viewing of any subjects that passes directly beneath the dome 1 2 11 Self diagnosis There is a self diagnosis procedure for the engine and the camera when dome boots up It can display the detect result and the initialization information 1 2 1
34. s NO 2 2 System Layout Please refer to Figure 2 1 for system cable connection Power Power Network Input Output Output Figure 2 1 2 3 Alarm Connection You can refer to Figure 2 2 for detailed alarm connection information Others Alarm Controller Figure 2 2 3 Quick Configuration Tool 3 1 Overview Quick configuration tool can search current IP address modify IP address At the same time you can use it to upgrade the device Please note the tool only applies to the IP addresses in the same segment 3 2 Operation Double click the ConfigTools exe icon you can see an interface is shown as in Figure 3 1 In the device list interface you can view device IP address port number subnet mask default gateway MAC address and etc J Config Tool Device List SW IP Address 10 15 5 111 10 15 5 84 10 15 5 82 10 15 5 88 10 15 5 254 2001 250 3000 1 1 2 112 fe80 9202 aff e04 7021 64 10 15 5 186 10 15 6 137 10 15 5 139 119202 a9ff eT8 1a 64 Subnet Mask 255 255 0 0 255 255 0 0 255 255 0 0 255 255 0 0 255 255 0 0 Port 37777 40002 40003 40007 40006 40006 40008 37777 37777 37777 37777 Default Gateway Mac Address 10 15 0 1 90 dT eb c3 2001 250 300 fe80 255 255 0 0 255 255 0 0 255 255 0 0 e80 9202 a9 e08 7494 64 10 15 5 149 e80 9202 a9 e0T fdc5 64 10 15 5 135 192 168 1 1T 10 15 5 8
35. speed dome title or not BACK Go back to the previous menu EXIT Log out system menu 5 4 3 Camera Setting WB SETTING EXPOSURE SETTING DAY NIGHT SETTING FOCUS MODE AUTO FOCUS LIMIT 30CM ZOOM SPEED 08 DIGITAL ZOOM OFF APERTURE 09 NEXT PAGE BACK EXIT Move the cursor to CAMERA SETTING and then click confirm button you can go to the submenu WHITE BALANCE SETUP It is to set the camera white balance mode There are several options Please use the left right button on the keyboard or in the speed dome terminal menu to set EXPOSURE SETTING It is to set the camera exposure mode gain and etc Move the cursor to current option and then click confirm button you can go to the third menu 14 DAY NIGHT Set day night mode It includes the third level menu Please move the cursor to highlight current item and then click the OK button to go to the sub menu Please use the left right button on the keyboard or in the speed dome terminal menu to set e FOCUS MODE There are several options Please use the left right button on the keyboard or in the speed dome terminal menu to set e FOCUS LIMIT It is to set the distance between the speed dome and the monitor object It can avoid the focus on the enclosure if the focus distance is too near and you can change the focus distance to set the focus speed There are several options Please use the left right button on the keyboard or in the speed dome terminal menu to set e
36. tes Disable recommended except those listed in trusted and G Enable not secure restricted zones Prompt 9 Initialize and script Activex controls not marked as safe for s Disable recommended Enable not secure Prompt Security level For this zone Allowed levels For this zone Medium to High Medium high C3 Appropriate For most websites T Prompts before downloading potentially unsafe 9 Run Activex controls and plug ins content O Adminictratar annravad lt T Unsigned Activex controls will not be downloaded Takes effect after you restart Internet Explorer SFSR Reset custom settings Reset to medium high default ims Figure 4 3 After you logged in you can see the main window See Figure 4 4 WEB SERVICE 000 AT SS 000 a A y 1 000 speed 1 2 gt Figure 4 4 Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction 10 5 Menu 5 1 Screen Menu Index Note ERR means current setup is invalid Please restore speed dome factory default setup Slight difference may be found in the parameter interface due to different product series SYSTEM INITIAL INFORMATION INFORMATION ADDR INFORMATION ENGLISH DISPLAY SETTING PRESET TITLE AZIMUTH DISP POSITION ZOOM DISP INSIDE TEMP TITLE DISPLAY BACK CAMERA SETTING WB SETTING A EXPOSU
Download Pdf Manuals
Related Search