DJI E1200 Standard
Contents
1. Arduino etc which may use the FTDI chipset connected to the computer If any of these FTDI devices are connected simply unplug them and keep the DJI Updater connected to the computer Then restart the DJI ESC Assistant and the ESC system and the two should connect 8 ESC LED Indicators amp Sound Definitions The definitions are the same for both the outer ESC LED Indicators and inner ESC LED Indicators as shown below LED Indicators Sound Description i IB pr erry Vi Ke Yellow Green blinking in turn None Motor is connecting Red or Green blinking slowly ME Bu XAY Gy hid Bed cr Green None Motor has started normally None Self test failure oe BB BB BB Input voltage is abnormal Red Yellow blinking in turn The motor s parameters BBB BBB don t match the firmware data saved in the ESC YY e Throttle stick is not at the BBBBBB Yellow blinking quickly bottom position 2015 DJI All Rights Reserved 5 EN EN Yellow blinking slowly B B B _ No signal input YE M ing at full Y Solid Yellow niere otors are rotating at fu throttle on eee ane Error land your aircraft Red blinking quickly immediately Learn more about the possible errors by connecting the ESC to the ESC Assistant i You can instantly tell what the unit s status is by observing the LEDs and listening to the sounds emitted from the ESC 9 Sp2. DJI E1200 Standard Tuned Propulsion System User Manual 2015 5 ciji Disclaimer Thank you for purchasing the E1200 Standard Tuned Propulsion System hereinafter referred to as product Read this disclaimer carefully before using this product By using this product you hereby agree to this disclaimer and signify that you have read it fully Please install and use this product in strict accordance with the User Manual SZ DJI Technology Co Ltd and its affiliated companies assume no liability for damage s or injuries incurred directly or indirectly from using installing or refitting this product improperly including but not limited to using non designated accessories Ensure that your ESC firmware is up to date and is compatible with the motor you will attach it to Otherwise you will be responsible for all resulting consequences caused by your own actions This device complies with part 15 of the FCC Rules DJI is the registered trademark of SZ DJI Technology Co Ltd abbreviated as DJI Names of products brands etc appearing in this manual are trademarks or registered trademarks of their respective owner companies This product and manual are copyrighted by DJI with all rights reserved No part of this product or manual shall be reproduced in any form without the prior written consent of or authorization from DJI This disclaimer is produced in various languages In the event of variance among different versi
3. d of the propeller mount then tighten the screws CW or CCW Mark Screws for Propeller EN Cover M3x8 lt Clockwise gt gt Counter clockwise A Loose screws cannot be securely locked in place with thread locker 6 ESC Port Description There are two ports on every ESC They are the Outer ESC LED Port and O the Data ESC Firmware Update Port These ports will be clearly marked on the ESC ESERIES 6405 6S 40A 261V Prone A Ensure that the ESC firmware is up to date and is compatible with the motor you will install Refer to the tag on the back of the ESC to see the default version of the firmware sO e Mount the outer ESC LED Indicators according to your needs The Data ESC Firmware Update Port is used to update the ESC firmware and adjust the ESC To do this visit the official DJI website to download the DJI ESC Assistant G http www dji com product e1200 standard download 7 Using the DJI ESC Assistant The DJI ESC Assistant is used to upgrade the ESC s firmware configure the propulsion system etc A An Updater is required and is not included with the E1200 Standard To use the DJI ESC Assistant connect the ESC to a computer through the Updater as shown below 4 2015 DJI All Rights Reserved ESC Updater Computer Before using the Update
4. e Z Blade 17 inch foldable propellers are made from an advanced carbon fiber reinforced polymer which reduces rotational inertia and enhances rigidity New upgraded 4216 motors promote efficient heat dissipation which improves endurance and reliability even when flying in harsh environments The 640S Smart ESCs feature a sinusoidal drive which is more efficient and allows for greater agility Highly visible LED indicators show real time motor status information making flying even safer Furthermore the ESC firmware can be upgraded by users effectively future proofing the E1200 1 In the Box 4216 Motor 4216 Motor Clockwise rotation x1 Counter clockwise rotation x1 1760 Foldable Propeller 1760 Foldable Propeller Clockwise x1 Counter clockwise x1 ae 640S ESC x2 Outer ESC LED Indicator x2 Accessory Package Screws for foldable propellers M3x12 5 hexagon Screws for propeller mount cover M3x8 JST 3 Pin Cable x2 Prop ee Propeller Washers 2 Gain Value Setting The new E1200 Standard ESC features a sinusoidal drive which replaces the traditional square wave drive to offer improved performance when accelerating and decelerating To achieve the same sensitivity as older ESCs which use a traditional square wave drive reduce the gain values according to your flight control system and frame The table below shows typical gain values when using the E1200 Standard with a DJI A2 flight control system and a frame which ha
5. ecifications Max Thrust Takeoff Weight Recommended Takeoff Weight Max Battery Recommended Working Temperature ESC Max Allowable Voltage Max Allowable Current Persistent PWM Input Signal Level Signal Frequency Battery Weight with cable Weight without cable Motor Stator Size KV Weight Propeller Diameter Thread Pitch 3900 g rotor 25 V Sea Level 1200 1400 g rotor Sea Level 1700 g rotor Sea Level 6S LiPo 10 60 C 26 V 40 A 3 3 V 5 V Compatible 30 450 Hz 6S LiPo 729 35g 42x16 mm 310 rom V 205 g 17x6 inch 10 FAQs Remounting the Propellers 1 Use the two Foldable Propeller mounting screws M3x12 5 hexagon the two Propeller Cover mounting screws M3x8 and the four propeller washers to remount the propellers 2 First line up and apply thread locker into the thread of the propeller mount then tighten the screws until the propeller blades are securely clamped and can rotate freely 6 2015 DJI All Rights Reserved Screws for Propeller Cover M3x8 Screws for Foldable Propellers M3x12 5 hexagon Propeller Washers A Loose screws cannot be securely locked in place with thread locker EN Caution Propellers Check the marks on the screws and propeller covers before every flight If the propellers are loose the marks will not line up indicating that the screws should be tightened o o A If the two
6. ons the Chinese version shall prevail when the product in question is purchased in Mainland China and the English version shall prevail when the product in question is purchased in any other region Warnings When powered on the motors and propellers will rotate very quickly and can cause serious damage or injury Always be vigilant and make safety your top priority 1 Always attempt to fly your aircraft in areas free of people animals power lines and other obstacles 2 Do not approach or touch the motors or propellers when the unit is powered on 3 Ensure that there are no open circuits or exposed wires that can cause short circuits 4 Before flying ensure that the propellers and motors are installed correctly and that the propellers are unfolded 5 Check to ensure that all parts of the aircraft are in good condition before flying Do not fly with worn or damaged parts 6 Only use compatible authorized DJI parts Legend A Important A Hints and Tips If you encounter any problems or if you have any questions please contact your local DJI authorized dealer or DJI Support rid DJI Support Website www dji com support 2015 DJI All Rights Reserved 1 EN EN About The E1200 Standard Tuned Propulsion System is a multirotor propulsion system that is designed for multi rotor aircraft with payload limits of 7 15 kg The E1200 Standard is more efficient and secure and has better endurance Th
7. r unplug any other serial devices that are connected to your computer then follow the instructions below 1 2 8 4 x 5 Download the DJI ESC Assistant from the official DJI website Run the installer and follow the prompts to complete the installation process Connect one end of the Updater to the Data ESC Firmware Update Port Connect the other end of the Updater to a PC with a Micro USB cable Turn on the ESC system by connecting it to a 6S LiPo battery and do not disconnect the ESC from the computer until the configuration is complete Run the DJI ESC Assistant software and wait for the ESC to connect to the program Watch the indicators at the bottom of the screen When the ESC has been successfully connected the Computer Connection status will be solid green and the Data Exchange Indicator will blink blue Click the View Tab In the ESC Section check the current firmware version and ensure that the installed firmware is up to date If it is not click the link and follow the prompts to update it In the LED Color Section customize the colors of the ESC LED indicators A If the ESC is not automatically recognized by the DJI ESC Assistant the indicators at the bottom of the screen will show a solid green and inactive blue color if not connected check whether there is more than one DJI Updater FTDI USB adapter or other developer tool including but not limited to BeagleBone Raspberry
8. rectly Try to solder the cables firmly to the power hub at the proper length the wires should be just long enough to reach the soldering point face outwards and should not be bunched up in front of the soldering point Power hub cause short circuits A Make sure that there are no open circuits or exposed wires that can AF It is recommended that you solder a power connector onto the power hub 4 Mounting the Motors Mount each motor to a frame arm according to the motor dimensions and the size of the assembly hole 4xM3 Thread depth 4 mm 4xM3 Thread depth 4 mm ww ZL The screw size is M3 Mount the gt EN motors using the appropriate w screws 3 3 Note the thread depth and the mom size of the screws Using screws aS Y that are too long or too large may 48 7 mm damage the motor 2015 DJI All Rights Reserved 3 EN 5 Assembling the Propellers The propeller cover mounting screws M3x8 should be adjusted using an appropriate hex key 1 The propellers marked CW should be mounted to the clockwise rotating motors which have a mark The propellers marked CCW should be mounted to the counter clockwise rotating motors which have a gt gt mark 2 Use two propeller cover mounting screws M3x8 to mount and secure the propellers First line up and apply thread locker into the threa
9. s a diagonal wheelbase of 920 mm and a takeoff weight of 8 kg Basic Attitude Pitch Roll Yaw Pitch Roll Vertical 100 100 90 150 150 100 2 2015 DJI All Rights Reserved 3 Connecting the ESCs Tools Required Tools Power hub electric soldering iron and soldering tin Use To solder each ESC s power cable to the power hub 1 Please solder each ESC to the power pads on the power hub as shown in the figure below Make sure that the solder is firmly attached to the power pads and that there is no possibility for a short circuit The power cable is a coaxial power cable Do not damage the protector on the red cable to avoid short circuits 2 Connect the signal cable to your controller The signal cable s orange wire is for the control signal the signal cable s brown wire is for the GND and the red wire is reserved 3 Connect the motor to the ESC Test the motor and ensure that the rotation direction of each motor is correct If not switch the position of any two cables connecting the motor to the ESC to change the rotation direction ESC signal cable To the controller Motor Take the power hub in the figure for example The outer power pads are for the GND cables and the inner power pads are for the power cables The red core of the coaxial power cable is positive and the shielding layer of the coaxial power cable is negative Make sure to solder them cor
10. screws on the Foldable Propellers are switched or if other screws are used to mount the propeller the marks may not be accurate 2015 DJI All Rights Reserved 7 The content is subject to change Download the latest version from http www dji com product e1 200 standard If you have any questions about this document please contact DJI by sending a message to DocSupportedji com O 2015 DJI All Rights Reserved
Download Pdf Manuals
Related Search