SMARTFIND A5 EPIRB User manual
Contents
1. activating the EPIRB Avoid holding or blocking the antennas view of the Sky An EPIRB is an additional carry off safety device As the EPIRB signal may be blocked by aircraft metalwork it is recommended to activate it after landing and away from any shadowing by the aircrafts metalwork The EPIRB will not work well inside a vehicle due to metalwork shadowing Exit the vehicle activate the EPIRB and place it on the roof the hood or on the ground away from the vehicle Find the best sky view place the EPIRB on the ground with the antenna pointing towards the sky and ensure wind does not knock the EPIRB over A N CAUTION Do not stare directly into the strobe light of the operating EPIRB Page 8 Getting the best from your EPIRB Aboard ship DO e Place the EPIRB in the open clear of overhangs e Keep the EPIRB upright hold it if necessary DO NOT e Place the EPIRB close to large structures e Lay the EPIRB on its side e Place the EPIRB under cover e Secure the EPIRB lanyard to the vessel In a liferaft It is recommend that the EPIRB should float in the sea tethered to the survival craft using the lanyard provided Page 9 Bulkhead bracket installation When permanently installing the EPIRB to a vessel the bulkhead bracket should be securely fixed in an easily accessible location near to the main emergency exit The bulkhead bracket has two parts The EPIRB can be quickly unclipped fr2. cMurdo is a brand name operated by Signature Industries Limited The information and illustrations contained in this publication are to the best of our knowledge correct at the time of going to print We reserve the right to change specifications equipment installation and maintenance instructions without notice as part of our policy of continuous product development and improvement No part of this publication may be reproduced stored in a retrieval system or transmitted in any form electronic or otherwise without permission in writing from McMurdo a Division of Signature Industries Limited No liability can be accepted for any inaccuracies or omissions in the publication although every care has been taken to make it as complete and accurate as possible Page 1 IN EMERGENCY Remove the EPIRB completely from its bracket Pull the tear off tab up then press the activation button and slide the switch left An EPIRB is an emergency device for use only in situations of grave and imminent danger to life False alerts endanger lives Help prevent them by understanding how to look after the EPIRB Introduction Thank you for purchasing the Smartfind A5 Class 3 manually activated Emergency Position Indicating Radio Beacon EPIRB The Smartfind A5 EPIRB is primarily intended for use by NON SOLAS vessels When carrying a Smartfind A5 you enjoy the reassurance of a last resort safeguard against any life threatening incidents that may occur anywhe
3. ed ON and will start to flash slowly once the first transmissions are made 121 5 MHz transmission is taking place whenever the Red LED is flashing alternately with the strobe light Every 50 seconds the red LED will flash rapidly followed by a single long flash to indicate each 406 MHz transmission Deactivation Should the EPIRB be activated by mistake or if the emergency ends then the EPIRB can be turned OFF by moving the activation switch fully to the right The strobe light will stop flashing and the red LED will go out IF ON SLIDE SWITCH TO RIGHT Important After EPIRB activation and as soon as practical the Smartfind A5 EPIRB should be taken to a service agent who will fit a new switch anti tamper seal and check the battery condition If the EPIRB has been used for more than 6 hours in total a set of fresh battery packs should be fitted to ensure the full 48 hour operational life is still available Page 5 Refitting into the bulkhead bracket Hold the bracket collar open and drop the EPIRB in the EPIRB body has side alignment slots to guide it into the locating lugs on each side of the bracket collar Hold the collar shut and fit the R clip to secure the EPIRB Fold over the antenna and locate the end moulding in the retaining slot Align slot with lugs Locate end of ie antenna in slot Stow the antenna whip Fit the R clip Page 6 Self test Self test button The EPIRB has a built in
4. ed to provide the national authority with the information as shown on the registration card This obligation transfers to all subsequent owners The authorities will normally provide the registered user with a DECAL label which you are obliged to fit to the EPIRB body as proof of registration User registration point of contact Australian users address all correspondence to Beacon Registration Section AUSSAR Australian Maritime Safety Authority GPO Box 2181 Canberra City ACT 2601 Fax International 61 2 6230 6868 Local 1800 622 153 Email ausbeacon amsa gov au Phone 61 2 6279 5041 or 1800 406 406 New Zealand users address all correspondence to Rescue Co ordination Centre New Zealand PO Box 30050 Lower Hutt 6009 Fax 64 4 914 8388 Email 406registry maritimenz govt nz Phone 64 4 914 8383 AFTN NZWNYCYX Inmarsat C 582451200067 Page 18 McMurdo A Division of Signature Industries Ltd Silver Point Airport Service Road Portsmouth PO3 5PB United Kingdom Phone 44 0 23 9262 3900 Fax 44 0 23 9262 3998 Email customerservice mcmurdo co uk Website www mcmurdo co uk 82 810 004 Issue 1
5. emove the EPIRB completely from the CARRYSAFE collar to gain access to the rear facing activation switch 1 Release the antenna tip 2 Pull the R clip out of the bracket and release the retaining strap 3 Lift the EPIRB out of the CARRYSAFE collar Activate the EPIRB only in an emergency 1 Break off the protective tab pull it upwards 2 Push the switch catch in and move the switch fully to the left ON position ONLY IN EMERGENCY Q tear tas push amp SLIDE LEFT The antenna should be positioned as upright as possible with a clear view of the sky Page 4 When the EPIRB is first switched ON the strobe light will start to flash immediately the first alert transmission is made after 50 seconds This short delay allows time to turn the switch back to the OFF position if the EPIRB was activated in error and before the first emergency alert transmission is sent e While the red LED remains ON continuously the EPIRB is activated but has not yet made an emergency alert transmission Strobe Light The strobe light provides a visual means of locating the EPIRB It will start flashing immediately after the Smartfind A5 is switched ON Its flashing will pause for a short time when each 406 MHz alert transmission is sent which is once every 50 seconds Strobe Light indication EPIRB ON a ae yee 1 flash every 3 seconds pause every 50 seconds Red LED The red LED illuminates when the EPIRB is first switch
6. et O Connor 6163 Ph 08 9331 0000 Fax 08 9314 2929 Email wa amisales com au South Australia AMI Sales 12 Brock Street Port Adelaide 5015 Ph 08 8341 2055 Fax 08 8341 1037 Email sa amisales com au Page 17 New South Wales AMI Sales Unit 1B 408 Victoria Road Gladesville 2111 Ph 02 9816 7100 Fax 02 9817 3755 Email nsw amisales com au Queensland AMI Sales Unit 1 14 Hopper Avenue Yatala 4207 Ph 07 5540 6800 Fax 07 5546 7044 Email qld amisales com au Annex 1 Registration information Advice of EPIRB Purchase or Transfer Registration of 406 MHz satellite EPIRBs with the EPIRB Registration Section of the national authority is mandatory because of the global alerting nature of the Cospas Sarsat system The information provided in the registration is used only for search and rescue purposes Fill in the owner registration card immediately upon completion of the sales transaction Mail fax or email the registration card to the national authority refer below immediately Registration cards are also available on line If the beacon is to enter service immediately complete the registration card and fax or email the information to the relevant national authority If the beacon is being transferred to a new owner the current owner is to inform the national authority by email facsimile letter or telephone of the name and address of the new owner The new owner of the beacon is requir
7. ilful damage negligence abnormal working conditions failure to follow McMurdo s instructions whether oral or in writing including a failure to install properly and or to use batteries recommended and or supplied by McMurdo misuse or alterations or repair of the product by persons other than McMurdo or an Approved Service Agent for parts materials or equipment not manufactured by McMurdo in respect of which the buyer shall only be entitled to the benefit of any warranty or guarantee given by the manufacturer to McMurdo for the battery storage life which is specifically excluded from this warranty if the total price for the product has not been paid THE LIMITED WARRANTY STATED ABOVE IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTY EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE McMurdo will not be liable for indirect special incidental or consequential damages of any kind sustained from any cause In no event shall McMurdo be liable for any breach of warranty or other claim in an amount exceeding the purchase price of the EPIRB This warranty does not affect any statutory rights of the consumer In order to be valid claims must be made under the above warranty in writing as soon as practicable after discovery of the defect or failure and within the warranty period referred to above Proof of purchase will be required The claim should be sent together with the product
8. in question to the address set out below or to an Approved Service Agent Following a valid warranty claim McMurdo shall be entitled to repair or replace the product or part in question free of charge or at McMurdo s sole discretion to refund to the buyer the price of the product or a proportional part of the price McMurdo shall not be liable to a buyer who is not a consumer for any other loss or damage whether indirect special or consequential loss of profit or otherwise costs expenses or other claims for compensation which arise out of or in connection with this product In the case of a consumer McMurdo shall only be liable where other loss or damage is foreseeable Nothing shall limit McMurdo s liability for death or personal injury caused by its negligence This warranty is to be interpreted under English law All enquiries relating to this warranty or Approved Service Agents should be sent to McMurdo a Division of Signature Industries Limited Silver Point Airport Service Road Portsmouth Hampshire PO3 5PB UK Telephone Int 44 0 23 9262 3900 Fax Int 44 0 23 9262 3998 Web www mecmurdo co uk Email customerservice mcmurdo co uk Page 16 CAM WWW amisales com au McMurdo products are sold in Australia by AMI Sales for General Enquiries and Warranty Service Support visit AMI on line Website www amisales com au or contact the nearest AMI Sales branch office Western Australia AMI Sales 107 Forsyth Stre
9. lice by radio or telephone to advise them of the false alert You may be asked to provide the UIN 15 digit Hex ID number of the EPIRB date time duration cause of activation and geographic location at the time you switched off the EPIRB Routine maintenance Self test the EPIRB monthly check that the battery is in date and examine the outer case and bracket for any signs of damage If required clean the outer case with fresh water wipe dry and examine the EPIRB and bracket for any damage A N CAUTION Never use chemical solvents to clean the EPIRB or bracket After activation The anti tamper switch cover must be replaced by a service agent A N CAUTION The battery may be run down and need replacement see below Inadvertent operation The anti tamper switch cover must be replaced by a service agent and the remaining battery life checked see below Battery replacement The exact battery expiry date is marked under the EPIRB lens dome The batteries must be replaced when e he expiry date has been reached or e The EPIRB has been used in an emergency situation or e A false activation exceeds 6 hours of use Servicing Service of the EPIRB should only be carried out by a McMurdo approved service agent Keep the original packing material for reuse whenever the EPIRB is sent for battery replacement or service Page 13 Transportation Passenger Aircraft This product contains small lithium metal batteries The Smartfi
10. mcmurdo SMARTFIND AS EPIRB User manual Safety notices WARNING An EPIRB is an emergency radio beacon Use only in situations of grave and imminent danger to life CAUTION False alerts endanger lives and cause disruption to Search and Rescue services Deliberate misuse of the EPIRB could result in penalty CAUTION Spring action antenna deployment tilt the EPIRB away from your face when deploying the antenna CAUTION Do not dismantle the EPIRB Contains no user serviceable parts CAUTION Contains lithium batteries Do not incinerate puncture deform short circuit or recharge CAUTION Dispose of a used EPIRB in accordance with local waste disposal regulations Refer to End of Life Statement CAUTION Avoid using chemical solvents to clean the EPIRB as some solvents can damage the case material CAUTION An EPIRB is a radio transmitter Some administrations may require that the user holds a valid radio licence to cover its ownership and use Radio Frequency Exposure Warning WARNING The EPIRB emits low levels of radio frequency radiation avoid handling the antenna once activated gt BPePRP BEER Pb Registration The EPIRB must be promptly registered with the appropriate National Authority Failure to register the EPIRB could delay a Search and Rescue SAR response and may be unlawful Ownership details Vessel Name Owner details EPIRB Unique HEX ID Pt tT Et TE ET EE TT YE Disclaimer M
11. nd A5 EPIRB can normally be taken on board a passenger aircraft as a personal item in carry on hand baggage McMurdo always recommends declaring the EPIRB to airline staff at check in in the same way you would for a laptop PC or video camera s air cargo This product contains small lithium metal batteries Due to the overall low level of lithium content the Smartfind A5 EPIRB is classed as not restricted as air cargo under IATA SP 188 Pl 970 Always check with the carrier concerned for any additional restrictions that could apply Specifications Part Number 82 803A Smartfind A5 EPIRB retail pack EPIRB Type Operation 406 MHz Transmitter 121 5 MHz Homer Strobe light Antenna Battery Environment Physical Fixing Standards applied Class 3 Manual activation Self test button Operating frequency Power output Modulation Operating frequency Power output Modulation Type Light output Vertical Type Operating life Storage Replacement Use Operating temperature Storage temperature Waterproof Buoyancy Exterior Finish Weight Height of body Length of antenna Overall Lanyard Two part Bulkhead bracket Satellite system EPIRB Page 14 Non float free Switch protected by anti tamper seal Checks transmitters battery and strobe light 406 028 MHz 1 kHz 5 W typical Phase 16K0GID 121 5 MHz 3 5 kHz 50 mW radiated typical Swept tone AM 3K20A3X Two high intensity LED
12. nd return it to the address indicated Some authorities allow online registration check the guidance notes printed on the registration form for further information Refer to Annex 1 for details of specific user registration requirements applicable for Australia and New Zealand Always ensure that any changes of registration or contact details are promptly notified Page 2 Overview An EPIRB is intended to be a one shot device once activated it will transmit emergency alerts for at least 48 hours The EPIRB will work best while floating in water but can also be operated while on board a vessel in a liferaft or on land when placed on the ground The key components of your EPIRB are Antenna Flexible whip should be near vertical when operating Strobe light Flashing signal light visible through the clear lens dome when the EPIRB is switched on Red LED Indicates the current operating status visible through the clear lens dome Activation Protected by a tear off anti tamper tab Break the tab upwards push the switch switch in and move it fully left to activate the EPIRB Test button Self test verifies the readiness of the EPIRB Lanyard Pull the lanyard spool down to free it Use the cord to tether the EPIRB to a PFD or survival craft Antenna Test button Strobe light Red LED Activation switch brake off the anti tamper tab to gain access to the Lanyard activation switch beneath Page 3 Activation procedure R
13. om the bulkhead mount for easy stowage while still held in the CARRYSAFE collar Press catch and lift the CARRYSAFE collar Bulkhead bracket installation When selecting a suitable mounting position consider e Ease of access in an emergency e Position at least 1 metre from compass equipment and 50 cm from powerful magnets e g magnets found in loud speakers and radio equipment e Allow sufficient clearance above the EPIRB to allow for easy removal from the bulkhead bracket Page 10 Mounting procedure The bulkhead bracket is designed to mount on a flat surface using four fixing points Four stainless steel screws 25mm in length are included Check that the rear side of the mounting surface is clear and that the fixing screws will not penetrate through into any other objects Offer the bracket into the chosen position and mark through the mounting slots using the bracket as a template Drill four 3mm 1 8 holes and securely screw the bracket in place Ty f A 71 130mm Stowage options The CARRYSAFE collar provides additional protection for the EPIRB if you intend to keep it in a carry off safety ditch bag or when transporting the EPIRB from place to place Page 11 Marking a vessel name In case of loss and to aid in its quick recovery we recommend marking the EPIRB with your vessel name and or ownership details A set of alpha numeric stick on letters are provided these can be stuck on
14. ours self testing and operation then the battery must be replaced to ensure that in an emergency it will still operate for a minimum of 48 hours at 20 C as required by International regulations lf the EPIRB fails self test it should be immediately removed from service Refer to the maintenance section for further information Page 7 Choosing the best location The Smartfind A5 EPIRB will work best when under an unobstructed view of the sky If it is not possible to pick a location with a totally unobstructed view of the sky still do your best to maximise the sky view Aboard vessel Liferaft Lifejacket On foot Aircraft Vehicles Land Stand the EPIRB on the deck choosing a position with the best sky view Ensure that the wind does not knock the EPIRB over Never secure the EPIRB lanyard to a vessel in danger of sinking Attach the securing lanyard to the liferaft or your clothing to avoid loss of the EPIRB if you are thrown out of the liferaft Activate and deploy the EPIRB into the water and let it float nearby on the end of the lanyard Operating the EPIRB inside a Liferaft or under a canopy can reduce its performance Attach the securing lanyard cord between the EPIRB and clothing to avoid loss of the EPIRB Activate and deploy the EPIRB into the water allow it to float close by Avoid holding or blocking the antennas view of the sky lf you must walk for help ensure the antenna remains vertical after
15. re in the world If you find yourself in a remote area without any other form of emergency communication on sea or land your Smartfind A5 can call for help Smartfind A5 will transmit a unique emergency message identifier via the Cospas Sarsat satellite system which can determine your location anywhere on the earth s surface In most cases the first emergency alert is received within 5 minutes of activation but depending on satellite coverage at the time this can sometimes extend to 45 minutes When the emergency alert message is received at a Rescue Co ordination Centre RCC it is cross referenced using the unique identifier often called Hex ID against your registration details Details of the alert are forwarded to the appropriate local Search and Rescue SAR teams Keeping your registration details upto date is critical to ensuring a quick SAR response Smartfind A5 has a secondary homing transmitter which allows SAR teams to direction find or home in on the EPIRB once they arrive on the scene Smartfind A5 has a storage life of 7 years and once activated will continue to transmit emergency alerts for a minimum of 48 hours For further information visit Cospas Sarsat on line at www cospas sarsat org User registration The EPIRB s unique identifier must be registered with the national authority indicated in the white area of the label on the rear of the EPIRB Complete the user registration form included with your purchase a
16. s 0 75 cd minimum Whip Lithium metal 48 hours minimum 7 years By service centre Logged by microcontroller 20 C to 55 C 30 C to 70 C Immersion to 10m Floats Highly visible yellow 770 grams 21 cm 18 cm 39 cm 5 5m 40Kg breaking strain Removable CARRYSAFE collar Cospas Sarsat T 001 T 007 IEC 61097 2 AS NZS 4280 2 End of Life Statement At the end of the products useful life it is vital that the battery is removed from the main body of the EPIRB to prevent false alerts False alerts cause expensive disruption to Search and Rescue services and may endanger lives as a consequence Safe disposal Contains traces of lithium may contain traces of lead and brominated flame retardants BFRs both in the housing material and circuit boards DO NOT INCINERATE McMurdo strongly recommends that this EPIRB product is disposed of in a sensible and considerate manner For example do not simply discard the product in the domestic waste Instead take it to a civil recycling facility or contact McMurdo for further advice Page 15 Warranty Statement mcmurdo McMurdo is a brand operated by Signature Industries Limited Subject to the provisions set out below McMurdo warrants that this product will be free of defects in materials and workmanship for a period of five years from the date of purchase McMurdo will not be liable to the buyer under the above warranty or any defect arising from fair wear and tear w
17. self test capability that will confirm when the battery is healthy both distress transmitters are functional and that the strobe light is operational It is recommend to self test the EPIRB monthly more frequent self testing can put unnecessary drain on the battery When self testing a specially coded test transmission is sent that will not alert the authorities A self test can be made while the EPIRB is still in the CARRYSAFE bracket The self test should be carried out during the first 5 minutes of the hour so as to minimise any disturbance of the emergency channels 1 Push and hold the TEST button down until the red LED indicator lights 2 A successful self test will result in the red LED and strobe light flashing together a number of times 3 The number of strobe light flashes indicates past battery usage Accumulated Battery Use Number of strobe light hours flashes 0 to 4 3 4to6 2 More than 6 1 Once the self test has completed the EPIRB will switch off automatically A self test failure will result in NO strobe light flash and the red LED turning OFF Important Unnecessary self testing of the EPIRB can reduce the overall run time available in an emergency Each self test draws a small amount of energy from the battery On average self testing of the EPIRB should be monthly and limited to a total of 84 times across the seven year battery storage life lf the EPIRB has been activated for a cumulative period in excess of 6 h
18. the rear label area go z Q 2 gp 2 gao ss 9 33535 2 5 30 Cf Q jle p 2 30 25 3 mS g 208049 59 VaR S586 wz 40 Jer j2 noL amp Sa mg SS2P 05 T 33 353mg 550N0 N es M V PP g oO ee 224 090 Og VU a S sTo one as 2 oD SZ Con eznzcm oongozam oongozamp ONNXVVOL TY OND XMOC TIP OND XHMOC TD OnNWxXAOATN ONOxKXHAOA TNU Pick off the required letters a small knife blade works well 2 Fix each letter to label area on the rear of the EPIRB 3 Cover the letter text for protection using the clear label material also supplied Dealing with a transmitting EPIRB In the unlikely event that the EPIRB develops a fault and will not turn off transmissions can be prevented from reaching the satellite by cutting off the antenna close to its base The EPIRB should then be wrapped in metal foil or placed in a sealed metal container or steel locker Take care when handling the antenna refer to product safety warnings e Contact the authorities to notify them of the false alert see below e Leave the EPIRB for 3 days or until the battery has fully run down before having the EPIRB serviced Page 12 False alerts If the EPIRB has been accidentally activated or if rescue is effected before arrival of the rescue services e Switch off the EPIRB and notify the appropriate rescue services or authorities at the earliest possible time e Contact the rescue services coastguard or po
Download Pdf Manuals
Related Search