Downloads - Wincor Nixdorf
Contents
1. Insert the second hard disk and fix it with the four screws Fix the drive rail with the two screws and the buffer screws to the hard disks Please pay regard to the correct fitting position Connector bar Drive rail BEETLE M II plus User Manual 35 36 Insert the hard disks in reverse order Make sure that the buffer screws are corresponding to the stampings in the base plate see arrows BEETLE M II plus User Manual P USB Hub optional There are four 12V P USB interfaces on an optional available board They allow the connection of peripherals such as printers and scanners Devices like Hard Disks may also be connected via a USB interface This interface can also be used as a USB A socket ee coo eee eee 10 0 0 0 00000 0 0 an S I e008 0 0 N oe CC reeeee 0 0 0 0 0 Ree eee i U 0 0 0 0 0 J ee Always use this onboard P USB 12V to connect a BA82 or BA83 with additional options or any other multifunctional screens BEETLE M II plus User Manual 37 COM5 COM8 Interfaces optional 38 The standard system is configured with four COM interfaces COM1 con nector not power supplied and COM2 COM4 sockets power supplied In addition expansions are possible via a motherboard connector COM5 COM6 onboard interfaces are available optionally The maximum expansion stage o2. Manual The System BEETLE M II plus Front Side View WINCOR NIXDORF BEETLE M II plus D0 venran ss Donor ae Power Button With a power supplied power unit you switch on the system with the power button BEETLE M II plus User Manual 15 Light Emitting Diode LED The LEDs are labelled with while the hard disk is beeing HDD SSD right LED flashes yellow ad wing left LED lights orange Stand by mode POWER left LED lights green Device is switched on USB Universal Serial Bus A USB 2 0 You can connect several USB peripheral devices to the USB or powered USB interface 12V or 24V a Only connect devices and cables that comply with the valid USB Specification 16 BEETLE M II plus User Manual Interior View e e e o e eo tone e e e e atat RIS e e e alato ato 29 m ap oog e e e e atoto soree eee ato e A Power Supply BEETLE M II plus User Manual 17 Connector Panel Power Supply The power supply automatically adjusts to the particular voltage and is fan cooled For the specified ratings see page 44 Technical Data y The power pack must be removed or replaced by authorized qualified personnel only Only replace power packs released by Wincor Nixdorf Y To disconnect the device from the supply voltage completely switch off the device and disconnect the power plug The Po
3. The diameter of the screw shank cannot be larger than 3 5 mm and the diameter of screw head not more than 8 5 mm and the height of max 3mm Dimensions in mm max 8 5 46 BEETLE M II plus User Manual Total Current Consumption of Interfaces The total current consumption at 5V interfaces must not exceed 5A Each COM 300mA in total 1000mA Each USB 500mA in total 2A Each USB HUB 500mA in total 2A TFT LCD Display Max 5A 5V The total current consumption at 12V interfaces must not exceed 5A Each COM 600 mA in total 900mA Each USB 1 5A in total 2A Each USB HUB 1 5A in total 2A TFT LCD Display Max 5A 12V The total current consumption at 24V interfaces must not exceed 3A each PUSB 24V 3A 24VDC power supply BEETLE M II plus with UPS Max 3A 24V Power loss of additionally implemented PCI and PCle Controllers is for thermic reasons limited to 10W for each slot and all together to 20W BEETLE M II plus User Manual Abbreviations 48 CATS CATSe CE CFC CHC COM COMn CPU CUL DIN DP D Sub DVD DVD RW DVI I EC ESD HDD IEC ISO LAN LED PCI PCle PEN PLINK POS Computer assisted testing system 5 European Symbol of Conformity Chlorofluorocarbon Chlorinated hydrocarbon RS 232 Interface Powered COM Interface Asterisk denotes Power Central Processor Unit Canadian Registration Recognized by UL Deutsches Institut
4. connect several USB peripheral devices e g scanner or scales to these USB Only connect devices and cables that comply with the valid USB specification BEETLE M II plus User Manual RJ45 LAN Here you connect the cable for the connection to a network LAN LEDS constantly green Network connected left LED flashes green Data transfer off 10 MBit s right LED 100 MBit s Only connect shielded LAN cables CAT5 CAT5e for 1000 MBit as these offer a better protection in case of interferences in a network BEETLE M II plus User Manual 23 Disconnecting Cables Never unplug a cable by pulling on the cable always take direct hold of the plug itself Follow the procedure below when disconnecting cables M Turn off all power and equipment switches mM Remove the cable cover if present M Unplug all power plugs from the grounded contact power sockets M Unplug all data communication cables from the sockets of the data networks M Unplug all cables from the devices With MINI DIN plugs Wincor Nixdorf keyboards the plug remains inserted until released Pull the plastic covering from the connecting socket with your thumb The lock is released The metal of the plug is visible To release a RJ12 plug push the latch under the plug to the top You loosen the USB A connector by pushing the covering of the connector 24 BEETLE M II plus User Manual BEETLE M II plus User Manual The P USB connector i
5. to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harm ful interference in which case the user will be required to correct the inter ference at his own expense Modifications not authorized by the manufac turer may void users authority to operate this device This class A digital apparatus complies with Canadian ICES 003 Cet appareil numerique de la classe A est conforme a la norme NMB 003 du Canada BEETLE M II plus User Manual 1 Note On the Laser If your device is equipped with a DVD DVD RW drive the following condition applies The DVD DVD RW drive contains a light emitting diode LED classified according to IEC 825 1 1993 LASER CLASS 1 it must not be opened Safety Notes The device may only be repaired by authorized qualified person A nel Unauthorized opening of the device and inexpertly carried out repairs may not only seriously jeopardize the safety of the user but also cancel all warranty and liability agreements Expansion cards with electrostatical
6. BEETLE M II plus switch on the POS system using the ON OFF button on the front panel The system first performs an automatic self test to test its basic functions For example you may see the following message on the monitor WN ID xx xx Date xx xx is the placeholder of the BIOS version number The system then determines the medium from which the operating system and POS application are to be booted Each medium is assigned a logical drive according to the configuration of your BEETLE M II plus A drive can be assigned to the following media E Network M Hard disk SSD M DVD m USB drive The logical drives are designated C and D The network is always assigned to the C drive during the run up proce dure The hard disk can be assigned to the C or D drive The system can only be started from the hard disk if the disk has been configured as C drive BEETLE M II plus User Manual Corresponding to the Setup configuration the modular BEETLE M Il plus system can be booted from the following drives Hard disk drive C DVD LAN module with BOOTPROM USB drive Please mind that the storage medium must be system boot capable If the POS system does not find a DVD it automatically continues the loading process from drive C If the operating system has started up without an error the application software is automatically booted if necessary A message is displayed as soon as the BEETLE M II plus is ready for op
7. ETLE Therefore you should connect your BEETLE or other IT devices only to power supply systems with separately guided protective earth conductor PE This kind of electricity system is known as TN S network Do not use PEN conductors Please also observe the recommendations of the norm DIN VDE 0100 Part 540 Appendix C2 as well as EN50174 2 5 4 3 Thus you can help to avoid possible malfunctions M You can connect or disconnect USB devices during operation of your BEETLE provided that these devices comply with the specifications ac cording to usb org Other peripheral devices such as PoweredUSB printer should be connected to or disconnected from your BEETLE sys tem only after the BEETLE has been switched off BEETLE M II plus User Manual Introduction The BEETLE M Il plus is the powerful high performance POS system for multifunctional solutions A powerful and energy efficient processor tech nology ensures a quick processing of all operations The BEETLE M Il plus boasts a wide range of standard PC and retail specific powered interfaces to connect the numerous peripherals Addi tional USB ports are accessible from the front to provide even more con venience The type and number of interfaces can be customized very flexi bly Optionally there is an DVD RW drive or a second SATA Hard Disk Drive available for your BEETLE M Il plus The choice of the software is not limited to a certain product This provides you with a co
8. WINCOR NIXDORF User Guide We would like to know your opinion on this publication Please send us a copy of this page if you have any constructive criticism We would like to thank you in advance for your comments With kind regards Your opinion Wincor Nixdorf International GmbH Documentation R amp D SAT36 Wohlrabedamm 31 D 13629 Berlin E Mail retail documentation wincor nixdorf com Order No 1750240395B BEETLE M Il plus Modular POS System 11 Motherboard User Manual Edition March 2014 All brand and product names mentioned in this document are trademarks of their respective owners Copyright Wincor Nixdorf International GmbH 2014 The reproduction transmission or use of this document or its contents is not permitted without express authority Offenders will be liable for damages All rights including rights created by patent grant or registration of a utility model or design are reserved Delivery subject to availability technical modifications possible Contents Manufacturer s Certification sssssssssssssessesssenesesss 1 NEStOG SALLY cie de etienne 1 PEC Class A Declara OM Ron m re ne 1 Not On the Laser ssh ea tir ne nt tn ir 2 Sale Note Soenen ne entendent 2 IMpOrtantiINOTeS i r E 3 INTrOQUCTION osea 5 About THIS MANU LES e a 5 Care Of the BEETLE M II plus 6 Recycling the BEETLE M II plus 6 Warrant ae E rE T E O Ar 7 BEETLE M II plus the Modular POS System
9. cccsssscsssssessseees 8 OVON TO Wisesana nerne n a O 8 Before Switching On the System ssccsccsscssccecccsccsccescesccsccecces 9 Unpacking And Checking the System 9 Setting Up The Device sta nina ta 10 Horzontal Installation stss sistema mise 10 Vertical Installation Of the Equipment ccccccccesseeeeeeeeeeeeeeeees 10 Mounting the Cable Cover 12 Cabling Of the BEETLE M II plUus cccssccssssscssssccssssecesscenescees 13 BASIC SCOURING Sx ensnsdasdteraqusenavennddner cand emarsonsanst aA E OSE 14 The System BEETLE M II plus csssccccsssccccsssccccssseccceeseccceesees 15 FROME SIC VISU specs chic scat rien seine A NA 15 POW Cl BUTON am sara cv nettoie 15 Light Emitting Diode LED ded wees tana eee 16 USB Universal Serial Bus A USB 2 0 16 HENO VIN nn mar anna na ein 17 Connector Panel 18 POWER SUPREME ni dede 18 DC24V Modular Printer niet 19 RIZ CASHDR scgecsvaissdcscatatsossansiakavedeiausvauastuivaledeciwanbavisatotaveainies 19 POWeFCONNECIO MESSE Sade tn E A Ne en A 19 NEN AIS nn ad manon 20 Jack Plug 3 5 mm MIC SPK RL 21 Minis DIN IY BD ne ie an ee E 21 D Sub Plue COM se nt tenace 21 PUSB POWEr d OS ends fau 21 D Sub Socket Power Supplied COM2 COM4 22 DW le PR A EE A E E A A ee 22 DispIV POR DP ran en 22 USB Universal Serial Bus 22 RAS TAN A ie eee 23 DISCONNECTING Cables tes N use 24 DVD RW Drive Optional c
10. ccssccsseccssccsseccesccseccescccseccesccees 26 Cla ga ies ener ree One nt rence nn E NAPA ES A A nr Met ere ane E Serer 26 Operating the DiGi vss nes nues encens 26 NOLES ABOUT DISCS onune ONON 27 Storage M diations 28 Change ofthe Data Store i NN er de aTi 28 Change of iwo DAS Ones ie nue a Sn us 32 P USB Hub optional ssessessessesseoseossossoessessessesseoseoseossossoesossoee 37 COM5 COM8 Interfaces optional 38 PLINK TFT Adapter optional 39 Battery 0oplonallsse ne nent este 40 Security In the Event Of a Power Outage 40 Starting Up the SystemM s sesessssesecececscsesecececscsesececececsesesecececeese 42 ADDENOIX MR Mein en anus 44 Technical Data BEETLE M II plus 44 PEON ACCS ES RS de a sde di one 45 Wali MOUNTING SE dire die cit 46 Total Current Consumption of Interfaces cccccceeseceeeeseeeeeeeeeees 47 ADBrevIAtiIOnS nn natale data AEE PET E 48 Manufacturer s Certification The device complies with the requirements of the 4 EC directive 2004 108 EC with regard to Electro magnetic compatibility and 2006 95 EC Low Voltage Directive Therefore you will find the CE mark on the device or packaging Tested Safety The POS system has been provided with the symbol for Tested Safety Gepr fte Sicherheit In addition the BEETLE has received the UL symbol and C UL US cUL symbol FCC Class A Declaration This equipment has been tested and found
11. ces are maintained and constant ventilation is provided The immediate ambient temperature of the system must not exceed 40 C 104 F WINCOR 60 mm Noo BEETLE M II plus m mm 100 mm Vertical Installation Of the Equipment Find four feet covered by a non skid rubber foil at the rear side of the BEETLE 10 BEETLE M II plus User Manual Remove these foils You see the keyholes for installing the BEETLE M II plus with four screws Oo By using a screwdriver remove each of the feet if necessary Oh S Turn each of them in the position needed for the wall mounting for example a For more information dimensions see the appendix chapter Wall Mounting page 46 E Mind the following minimum clearances also for vertical mounting to ensure sufficient ventilation see page 10 Forward 100 mm Backward 60 mm Sideways left 50 mm BEETLE M II plus User Manual 11 A surface made of nonflammable material e g concrete or metal must be located underneath the vertically mounted power supply unit Recommendation Mount the device with the side of the power supply unit side without ventilation slots facing upwards Mounting the Cable Cover Before mounting the optional cable cover you should first remove the cable openings where necessary This depends on the cables which you wish to lay Tools are not required as the plastic parts ca
12. cor Nixdorf International GmbH Make sure that the power plug is disconnected and that no liquid finds its way into the device Recycling the BEETLE M II plus Environmental protection does not begin when the time has come to dis pose of the BEETLE it begins with the manufacturer This product was de signed according to our internal norm Environmental conscious product design and development The modular BEETLE M II plus system is manufactured without the use of CFC and CHC and is produced mainly from reusable components and materials Please do not stick labels onto plastic case parts This would help us to re use components and material At the moment there are still some parts that are not reusable Wincor Nixdorf International GmbH guarantees the environmentally safe disposal of these parts in a Recycling Center which is certified pursuant to ISO 9001 and ISO 14001 So when your BEETLE M II plus it has served its time take advantage of the environmentally smart up to date recycling methods Please contact your competent branch or the Recycling Center Paderborn for European countries for information on how to return and re use devices and disposable materials under the following mail address Email info wincor nixdorf com We look forward to your mail 6 BEETLE M II plus User Manual Warranty Generally Wincor Nixdorf guarantees a warranty engagement for 12 months beginning with the date of delivery This war
13. cted to the BEETLE M II plus you must obtain a Wincor Nixdorf license for the driver software Make sure that the connector is plugged securely into the socket to prevent possible malfunctioning P USB Powered USB The P USB interface is qualified for connections of peripheral devices such as printers barcode scanners or customer displays The power supply is ei ther 12V or 24V marked red for POS printers A mechanical code avoids the plugging of a USB 12V connector into a USB 24V jack This interface can also be used as a USB A socket Always use this onboard P USB 12V to connect a BA82 or BA83 with additional options or any other multifunctional screens BEETLE M II plus User Manual 21 22 D Sub Socket Power Supplied COM2 COM4 The interface connection is a 9 pin D sub jack for scanner operator or customer displays without own power supply Power is supplied via this jack Make sure that the connector for a peripheral device is screwed firmly to the socket to prevent possible malfunctioning DVI I Via DVI interface a high resolution LCD monitor can be connected to the BEETLE system Video signals with a max resolution of 1920 x 1200 pixels 60 Hz can be transmitted DisplayPort DP DisplayPort is a standardised digital display interface with a max resolution of up to 3840 x 2160 pixel and a frequency of 30 pictures sec DP uses a smaller connector than DVI USB Universal Serial Bus A You can
14. e device as this may lead to electric shocks or short circuits M Never plug in or unplug data communication lines during thunder storms Protect devices from vibrations dust moisture and heat Always dispose of used parts such as batteries in an environmentally safe manner M The ventilation slots of the power supply must remain unobstructed to ensure sufficient ventilation of the equipment If the equipment is to be fitted you must ensure that the specified minimum distances are maintained and constant ventilation is provided mM n emergencies e g damaged housing or damaged power cable pene tration by liquids or foreign bodies the device must be switched off immediately the power plug disconnected and the Customer Service of Wincor Nixdorf or your dealer must be notified M The lithium battery must be disposed of in accordance with local regu lations for special waste In case of an improper change of the lithium battery it exist an explosion risk BEETLE M II plus User Manual 3 M The device may only be repaired by authorized qualified personnel Unauthorized opening of the device and inexpertly carried out repairs may not only seriously jeopardize the safety of the user but also can cel all warranty and liability agreements M Your BEETLE system is the result of modern technical innovation So please see for according structural and technical surroundings to guar antee a fault less and efficient work of your BE
15. e see next chapter For operating a battery the BEETLE M II plus must be equipped with a special UPS power supply unit WINCOR NIXDORF BEETLE M II plus BEETLE M II plus with battery Security In the Event Of a Power Outage 40 It takes approximately 6 hours to fully charge the battery after the unit has been switched on for the first time The system only charges the battery when it is switched on and the system software Wincor UPS software with WinXP Linux has been configured and loaded If a power outage occurs the system remains fully functional for a short period of time In such cases the battery supplies the system with power for continued operation This allows the unit to bridge power outages for a certain software dependent period of time BEETLE M II plus User Manual Peripheral devices with separate power supply units such as VGA moni tors are not supplied with battery power during a power outage This is also true if the peripheral devices are connected to the power outlet sockets of the POS system Battery The optional battery is delivered with a power switch and a power output socket on the power supply see also page 18 Before operating you have to switch on the BEETLE M Il plus with the power button on the device s front side BEETLE M II plus User Manual 41 Starting Up the System 42 After installing the
16. equirements at all times 8 BEETLE M II plus User Manual Before Switching On the System Unpacking And Checking the System Unpack the components and verify that the scope of delivery is identical to the information on the delivery ticket The carton contains the basic unit and a country specific accessories kit Some ordered composition may be installed Should you notice any transport damages or discrepancies between package contents and delivery ticket or functional defects please inform your contracting parties or the branch office of Wincor Nixdorf immediately Please indicate the number of your delivery ticket and delivery ticket position and serial numbers of the respective devices The serial number can be found on the label illustrated below sample The label is located at the bottom side of the housing WINCOR 100 120V 200 240V NIXDORF 6 3A 60 50Hz BEETLE M II plus 01750 xxxxxxxx MURDAN A ace in Serial number Transport the device only in its original packaging to protect it against impact and shock BEETLE M II plus User Manual 9 Setting Up the Device Set up the BEETLE M Il plus system where it will not be exposed to extreme environmental conditions Protect the device from vibrations dust moisture heat and strong magnetic fields Horizontal Installation Mind the minimum distances indicated below If the equipment is to be fitted you also must ensure that the specified minimum distan
17. era tion For more detailed information see the description of your application program BEETLE M II plus User Manual 43 Appendix Technical Data BEETLE M Il plus 310 mm 280 mm w o cable cover 369 mm with cable cover Height 126 mm Depth Weight approx 6 5 kg Climatic category Class 3K3 DIN IEC 721 3 3 Class 2K2 DIN IEC 721 3 2 Class 1K2 DIN IEC 721 3 1 Temperature Operating 3K3 5 C up to 40 C Transport 2K2 25 C up to 60 C Storage 1K2 5 C up to 40 C Processor INTEL Sandy Bridge 2nd generation 13 i5 i7 Processor family Input Voltage 100 120 V 200 240 V Max power consumption 6A 3A Frequency of the system voltage 50 60 Hz Mains power outlet 100 120 V 2A max p 200 240 V 1A max 44 BEETLE M II plus User Manual Interfaces COM1 w o power supply COM2 COM4 with power supply Option COM5 COM8 with power supply 2 Standard USB 2 Standard USB at the front side 1x 12V 1x 12V and 1x 24V PoweredUSB Option 4x 12V via PoweredUSB Hub Onboard Adapter for DVI I displays Resolution VGA up to 2048 x 1536 pixel a DisplayPort for monitors with high resolution Graphics Adapter up to 2560 x 1600 pixel and DVI D with a resolution of max 1920 x 1200 Option PLINK resolution 1600x 1200 pixel 24 Bit colours Spk Mic Ports for microphone and loudspeaker PS 2 1 keyboard and mouse BEETLE M II plus User Manual 45 Wall Mounting
18. f r Normung German Institute for Standardisation DisplayPort D Shaped Sub miniature Digital Video Disc Digital Video Disc Rewritable Digital Visual Interface integrated European Commission Electronically Sensitive Devices Hard Disk Drive International Electrotechnical Commission International Organization for Standardization Local Area Network Light Emitting Diode Peripheral Component Interconnect Peripheral Component Interconnect express Protective Earth Neutral Conductor Panel Link Point Of Sales BEETLE M II plus User Manual RAM SATA SSD TFT TN S UL USB VGA WN BEETLE M II plus User Manual Random Access Memory Serial Advanced Technology Attachment Solid State Disk flash medium Thin Film Transistor Terre Neutre Separ Underwriters Laboratory Universal Serial Bus Video Graphics Adapter Wincor Nixdorf International GmbH 49 Wincor Nixdorf International GMbH D 33094 Paderborn Order No 1750240395B
19. ffer screws to the hard disk Please pay regard to the correct fitting position Drive rail Connector bar Insert the hard disk in reverse order Make sure that the buffer screws are corresponding to the stampings in the base plate see arrows BEETLE M II plus User Manual 31 Change of two Data Stores First ensure that the device is switched off and that the power connector is disconnected Open your BEETLE M II plus by removing the housing cover Loosen the two screws at the back side see arrows e eae eeuwe ee 10 0 0000 e 2266 32 BEETLE M II plus User Manual Lift up the DVD drive Push the metal plates 3 Tilt the hard disks holder in direction of arrow 4 BEETLE M II plus User Manual 33 34 Loosen by hand the buffer screws 1 and remove the two Phillips head screws at the holder 2 with a screwdriver Remove the four screws of each 2 5 hard disk total 8 j bare electronics v Handle the hard disks with care when installing it and never touch Change the hard disks BEETLE M II plus User Manual Insert one of the hard disk into the housing and fix it with the four screws Please pay regard to the correct fitting position the label side shows to the window and the connector bar to the bottom Window Connector bar
20. ffers four more powered COM interfaces together with a PCI COM card Scanners customer and operator displays without power supply of their own are connected to these serial interfaces The interface connection is a 9 pin D sub jack Power 5V or 12V is supplied via this jack Make sure that the connector for the customer display is screwed firmly to the socket to prevent possible malfunctioning se OOOOOOOC A nee eee 6 00 0 0 0 0 0 006000 000000 0e A Le 0 0 0 0 6 0 0 0 0 0 0 6 O 000 0 0 6 D eeeeeeee eee0e 00006000 en 0000 00000000 eeeee See eee o o o o o la Do e o ee 0 0 0 0 0 0 0 a 9 JO Se Oe eta 000 O eee ee eeeec an eee ee eee 0 0 0 0 see i J eee CCC r D 0 0 0004 DOO O0 0 0 0 4 BEETLE M II plus User Manual PLINK TFT Adapter optional If you want to use your already existing display equipment you can con nect your screen to the PLINK TFT interface via a DP connector For connecting a display with touch function COM6 would be the default position on the motherboard The COM8 interface can be used alterna tively on the PCI card BEETLE M II plus User Manual 39 Battery optional The battery bridges any power failures up to 15 minutes and allows a controlled shutdown of the POS program by the appropriate softwar
21. llowed Example for a connector panel of the BEETLE M II plus with 11 Mother board Jack plug 3 5 mm MIC microphone 2 axmessmns ooo o rewruses SSS veusa osu power supped comerem come o qw So o Y o o m S avsa oo o ason SSS BEETLE M II plus User Manual Jack Plug 3 5 mm MIC SPK Physically the microphone MIC and the head phone SPK jacks are iden tical as both require 3 5 mm phone jack for data transfer However both differ concerning the assignment so that a faultless transmission is only ensured with the designated connection Besides a microphone a headset can be used alternatively via this interface The volume can be regulated via BIOS setup Mini DIN KYBD The BEETLE M II plus has a 6 pin mini DIN jack for connecting a keyboard Make sure that the connector is plugged firmly into the socket to prevent malfunctioning Power is supplied to the keyboard via this socket If you wish to connect an older standard PC keyboard with DIN connector you must use a special adapter cable obtainable from the WN branch office responsible for your area D Sub Plug COM1 Connect e g scales with their own power supply to the COM 1 interface COM1 is designed as a 9 pin D sub plug In addition to the keyboard you can connect a PS 2 mouse via a Y connector If scales which are notsupplied by Wincor Nixdorf International GmbH are conne
22. ly sensitive devices ESD may Ate be marked with this sticker Opening the device or handling boards fitted with ESDs you must observe the following aspects under all circumstances M You must always discharge yourself e g by touching a grounded ob ject before working with boards containing ESDs The equipment and tools you use must be free of static charges Pull out the power plug before inserting or pulling out boards contain ing ESDs Always hold boards with ESDs by their edges Never touch pins or conductors on boards fitted with ESDs 2 BEETLE M II plus User Manual Important Notes The modular POS system BEETLE M II plus conforms to the current safety standards for data processing equipment M If this device is taken from a cold environment into the operating room moisture condensation may form The device must be absolute ly dry before being put into service an acclimatization period of at least two hours must therefore be observed M This device is equipped with a safety tested power cable and may be connected only to a prescribed grounded contact power socket mM When setting up the device ensure that the power socket on the de vice and the grounded contact power socket are easily accessible M To disconnect the device from the supply voltage completely switch off the device and disconnect the power plug of the power supply mM Ensure that no foreign objects e g office clips find their way into th
23. n be removed by hand LUUCULE EG F Cat Cet _ wt om A 12 BEETLE M II plus User Manual Cabling Of the BEETLE M II plus All devices belonging to the modular BEETLE M II plus that have a separate power cable must be connected to the same electric circuit mM Remove the cable cover if present M Make sure that all data cables at the system unit and the peripherals are plugged E Plug one end of the DC cable into the socket of the BEETLE M II plus and the other end to the wall socket y Never connect data cables when the system is switched on WINCOR NIXDORF BEETLE M II plus z Je M i ey U eee J resesssasessese 7 BEETLE M II plus User Manual 13 ao Power Button at the front side At the front side of the system find the Power button which will turn ON and OFF the system Shortly press the Power button to start the system Switching off during operation is possible just press the Power button again for approx 5 sec Basic Settings Ex works the BEETLE M II plus is configured to your order Your configu ration must be subsequently adapted to support supplementary devices such as scanners For more information contact the Wincor Nixdorf International GmbH branch office responsible for your area 14 BEETLE M II plus User
24. nsiderable degree of flexibility when arranging the configura tion of your POS system Whatever configuration you need Wincor Nixdorf International GmbH offers the right solution So whenever you want to expand your BEETLE M II plus please contact your Wincor Nixdorf International GmbH branch office or your dealer http www wincor nixdorf com internet site EN EN Home homepage node html About This Manual This documentation is intended to help you to work with the POS system and to serve as a reference work The detailed table of contents help you find the desired information quickly and easily Notes in the manual are marked by this symbol i This symbol is used for warnings The type and scope of application programs depend on the customers own selection therefore software will not be discussed further in this manual BEETLE M II plus User Manual 5 For the peripheral devices of the BEETLE M II plus you can find detailed in formation in the respective manuals Also you will find a description of the BIOS Setup and the Central Processing Unit in a separate manual POS Motherboard 11 CPU See http www wincor nixdorf com internet site EN EN Support Downloads POSLotterySystems Manuals manuals node html Care Of the BEETLE M II plus Clean your BEETLE M II plus at regular intervals with a dry lint free cloth If that does not suffice please use a suitable plastic surface cleaner which can be ordered from Win
25. ranty engagement covers all damages which occur despite a normal use of the product Damages because of improper or insufficient maintenance improper use of the product or unauthorized modifications of the product M inadequate location or surroundings will not be covered by the warranty For further information on the stipulation consult your contract All parts of the product which are subject to wear and tear are not includ ed in the warranty engagement For detailed warranty arrangements please consult your contract documents Please order spare parts at the Wincor Nixdorf customer service BEETLE M II plus User Manual BEETLE M Il plus the Modular POS System Overview You can connect a variety of peripherals to your modular POS system BEETLE M II plus and thus implement a wide range of expansion stages You can connect a four line alphanumeric customer display and a four line cashier display Alternatively you can connect flat screens You can M use various types of scanners such as distance touch or stationary scanners M use scales and scanner scales please take into account the official certification regulations connect various printers use POS keyboards use different types of cash drawers integrate the BEETLE M II plus in a network and upgrade the BEETLE M II plus since it can accommodate expansion cards 1x PCI 1x PCI Express x4 This means that the BEETLE M II plus can meet your r
26. re available M one 3 5 SATA hard disk or M two 2 5 SATA hard disks or M one or two 2 5 solid state disk drives A solid state disk drive is a data storage drive that uses memory elements in place of a rotating disk to store data The SSD can substitute the hard disk and emulates a hard disk drive interface The most SSDs are flash memory based Change of the Data Store 28 First ensure that the device is switched off and that the power connector is disconnected Open your BEETLE M II plus by removing the housing cover Loosen the two screws at the back side see arrows QD BEETLE M II plus User Manual Lift the top cover at the back side 1 and pull it out of the front guide 2 a er 3 e S JE JE gag LT g fi i HE 41S b i ee 8 9 Lam S 7 e 6 6 ouv ees crete Lift up the DVD drive Push the metal plates 3 Tilt the hard disk holder in direction of arrow 4 BEETLE M II plus User Manual Lift up the drive and remove it Loosen the connecting cables Power supply cable Loosen by hand the buffer screws 1 and remove the two Phillips head screws at the holder 2 with a screwdriver Handle the hard disk with care when installing it and never touch bare electronics 30 BEETLE M II plus User Manual Change the hard disk Fix the drive rail with the two screws and the bu
27. s disengaged by pressing the spring that is marked by an arrow Manually loosen the knurled screws of the COM or DVI interface connector The DisplayPort connector is disengaged by pressing the button that is marked by an arrow To release a RJ45 plug push down the latch see arrow 25 DVD RW Drive optional General Optionally the BEETLE M II plus can be equipped with a DVD RW drive The LED at the drive lights up whenever the system accesses the drive Operating the Drive To start the drive follow the procedure below M Plug the power connector M Push the power button of the system M Press the ejection button see arrow WINCOR NIXDORF BEETLE M II plus mM The drawer is ejected from the drive M Place the disk into the drawer with the disks label facing up M Then push the drawer softly until it is locked in the drive 26 BEETLE M II plus User Manual Notes About Discs M Do not touch the surface of the disk Always handle it at the edges M Never write on a disk with a hard object like a ball point pen or pencil and never fix a label directly on the disk M Do not expose disks to direct sunlight and avoid storing them in areas subject to high temperatures or humidity M For best results periodically wipe each disk with a soft dry and lint free cloth gently rubbing outward from center BEETLE M II plus User Manual 27 Storage Media Following storage media a
28. wer Supply Unit PSU carries the 80plus Bronze certificate So less energy is needed and less noise is generated as the fan is much lesser activated with a low revolution speed BRONZE O DC24V Printer RJ12 Cash Drawer 18 BEETLE M II plus User Manual DC24V Modular Printer Appropriate POS printers can be connected via the low voltage jack 24V max 3A A connecting cable with a HOSIDEN plug is required for this y Connect only cables to the 24V connector which are marked with DP 1 or DP 2 y Do not connect the HOSIDEN plug when the system is turned on this can lead to an automatically reboot of the system RJ12 CASHDR The power supply unit has one RJ12 socket for connecting a cash drawer Make sure that the connector is plugged firmly into the socket to prevent malfunctioning RJ12 plugs lock in when you insert them Power is supplied to the cash drawer via this socket P24V 5 15 Connect cash drawers only no telephone set y Connecting daisy chained cash drawers and 12V OEM drawers is prohibited Power Connector This connector provides the power Connect the according end of the power cable to this port and the other end to the power socket Pull the mains plug to power off the device BEETLE M II plus User Manual 19 System Unit 20 Always make sure that the system is switched off when you do cabling works Connecting peripherals with the system switched on is not a
Download Pdf Manuals
Related Search