ENH900EXT Quick Installation Guide
Contents
1. need to ask your network administrator Static IP Address on the interface for the appropriate IP settings t Example 192 168 1 10 and the Obtain an IP address automatically i i i Use the following IP address Pole Mounting Kit Quick Installation Subnet Mask address as a ae a ENH900EXT Guide nea C552 350 Subnet mask 255 255 255 0 Default gateway a Obtain DNS server address automatically ENH900EXT ENH1750EXT Minimum Requirements version ne oe Use the following DNS server addresses A AK Preferred DNS server Broadband Internet Service m FA tp r 4 Aternat DNS server Dual Band Long Range Cable or DSL Modem Wireless Outdoor Access mone Pic Erle Safar Firefox Chrome E Validate settings upon exit 2 4 GHz Your model number may be different in the web browser interface 4 switching Modes Wall Mounting The AP Technical Support A This device can operate in the following modes Access Point Mesh and WDS A Mark the four locations of the mounting holes on the flat mounting C Place the lock and flat washers on the four hex cap screws and drive D Tighten the flat washers to secure the bracket to the Country of Purchase Service Center Service Information B Select the Operation Mode under Network Wireless tab surface the screws to attach bracket to the back of the Access Point mounting surface North America Canada rma engeniuscanada com www engeni2. 2 IP Address Configuration 3 Access Point Setup Package Contents T Connecting the Access Point nin noe A Connect one end of the Ethernet cable into the main LAN port PoE A Once your computer is on ensure T Local Area Connection Properties A To configure the Access Point open a web browser In the address bar of the Access Point and the other end to the AP Ethernet port on the that your TCP IP is set to On or Networking of the web browser enter 192 168 1 1 and hit enter POE injector Enabled Open Network Connect using _ B Connect the Power Adapter to the DC IN port of the PoE injector and Connections and then click Local ee FES 866 plug the other end in to an electrical outlet Area Connection Select Internet ioscan a i ini j M 0M Client for Microsoft Networks i Accessit AA E EE PEENE Power Adapter C Connect the second Ethernet cable into the LAN port of the PoE injector Protocol Version 4 TCP IPv4 E Peredaren New Tab x and the other end to the Ethernet port on the computer and then click on the Properties 5 GHZ Detachable Antennas X 3 v Broadcom Advanced Server Program Driver M 4 Intemet Protocol Version 6 TCP IPv6 CS Intemet Protocol Version 4 TCP IPv4 Link Layer Topology Discovery Mapper 1 0 Driver Link Layer Topology Discovery Responder a joja gt Control Panel gt Net
3. f devices in the network Features and specifications subject to change without notice This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Trademarks and registered trademarks are the property of their respective owners For United States of America Copyright 2013 EnGenius Technologies Inc All rights reserved 0 eee ad pS Se
4. s Middl 800 364 364 87 er Q on East General 971 4 357 5599 C Click on the Save button after you have modified the setting Click TRE nnn Russia f www engenius Mme com Changes button then click Apply button to apply all changes o ou have made b a E 70 j j www engeniustech com sg e_warranty_form aan Sla Ingapore ae ener techsupport engeniustech com sg l Oceania TOTIES www engeniustech com sg Singapore 1800 364 3648 it tees Q Others Taiwan R O C technology senao com www engeniusnetworks com Pole Mounting The AP Notes A Place the lock and flat washers on the four hex cap screws and drive B Drive the four round head screws to attach the Pole Mount Bracket to C Thread the open end of the Pole Strap through the two tabs on the D Lock and tighten Pole Strap to secure Pole Mount Bracket to the pole the screws to attach bracket to the back of the Access Point the bracket Pole Mount Bracket Horizontal Placement Vertical Placement Horizontal Placement g X sds pf 2 e GA Y e a CN D Ca y J fa m gy y a 7 4 g ey be DL oS r ey gt EnGenius Maximum data rates are based on draft IEEE 802 11ac and or IEEE 802 11 standards Actual throughput and range may vary depending on many factors including environmental conditions distance between devices radio interference in the operating environment and mix o
5. uscanada com Toll Free 1 888 397 2788 Local 1 905 940 818 ENH900EXT Dual Radio Outdoor AP 3T3R 450Mbps 450Mbps changes 0 Reset B Drill a 37mm deep 8mm hole in the markings and hammer the bolts into the openings overview Wireless Settings www engentustech com Los Angeles USA _ support engeniustech com Device Status Device Name ENH900EXT Toll Free 1 888 735 7888 Connections Country Region Please Select a Country Code Local 1 714 432 8668 Enable Disable Band Steering cles In sed Band Steering function to work properly both 24GHz and 5GHz SSID and security settings must be the same Central amp South America Miami USA miamisupport engeniustech com Management 2 4GHz 5GHz es engeniustech com lami 1 305 887 7378 Coud Settings Operation Mode Access Point O Access Point O Green pg engeniustech com SaO Paulo Brazil 55 11 3957 0303 Advanced Mesh Enable Mesh AP E D F Mexico 52 55 1163 8894 Time Zone Wireless Mode OFI Scheduler Channel HT Mode 20 40 MHz Tools Extension Channel Upper Channel E N th d support engeniusnetworks eu System Manager Channel Auto v Auto urope e eriands PP 8 Transmit Power Auto Auto y www engeniusnetworks eu 31 40 8200 887 Data Rate Auto oe Q RTS CTS Threshold 1 2346 2346 2346 Bee Client Limits 127 Enable Disable 127 Enable Disable au Africa Dubai UAE Support engenius me com Toll Free CIS UAE 800 EnGeniu
6. work and Internet Network Connection ww ap all Uninsta Properties Organize Disable this network device Diagnose this connection Description Transmission Control Protocol Intemet Protocol The default O 192 168 1 1 D Screw on the provided antennas to the device as shown in illustration below button M J2 File and Printer Sharing for Microsoft Networks Note The Access Point supports both IEEE 802 3at PoE Power over Ethernet or the included power Injector You may use either one as the power source DO NOT use both at the same time o see Con IEE ee Mou SonicWALL Netextenc B A login screen will appear By default the username of the Access Point 4 Broadcom Netlink TM Gigabit E SB SonicWALL NetExtendf is admin and the password is admin Enter the current username and PoE Injector Ground Cable Wall Mounting Kit ee password of the Access Point and then click Login m fi 5 GHz wide area network protocol that provides communication across diverse interconnected networks Disconnected Quick Installation Guide Internet Protocol Version 4 B If your PC is already on a network Jiffer q XK OU A N KUTT D Quick Installation Guide To Computer ensure that you have set it tO d You can get IP settings assigned automatically if your network supports i A this capability Otherwise you
Download Pdf Manuals
Related Search