LGK-3901 Miranda User Note 9Dec2014
Contents
1. XG device e The serial port type can be configured as RS232 or RS422 and the baud rate set to 1200 9600 19200 38400 57600 or 115200 e The serial port can also be set to receive Oxtel Automation commands or to transmit certain Oxtel Automation commands to a slave Intuition XG device For EAS the serial port will receive ENDEC 1822 and TFT EAS 911T protocols and for the temperature Probe it will received ST61XX TEMP SENS protocol COM 2 is an RJ45 port that provides identical functionality to COM 1 This allows two external devices for example Automation and EAS to independently control the LGK 3901 DSK 3901 The pin out of the COM 1 and COM 2 ports is Pin No Signal Name RS422 Signal Name RS232 1 TX RTS 2 TX TXD 3 RX CTS 4 NC NC 5 NC NC 6 RX RXD 7 NC NC 8 GND GND Communications Parameters The communications parameters for the devcie cannot be changed They are preset in the ADC device server The settings below are provided for your information Baud Rate 19 200 Data Bits 8 Parity none Stop Bits 1 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 3 of 17 O Imagine User Notes Device Server Set Up IMPORTANT Configuration Note When you have finished making changes on a configuration screen press Apply and all changes made upon the current configuration window will be applied to the driver Press OK and any confi2. 00 00 10 00 oo 00 00 00 Jv JPT isz50 Plav AS123 00 00 20 00 00 00 00 0 __ _ _ __1_ Demening __ Test audio type 00 00 10 00 a a m A ae Test FPT tune Example Playlist with secondary Data events of IS750 LGK 3901 Example of DSK 1 as Layer 2 DSK 2 as Layer 3 and DSK 3 as Layer 4 with IS 750 LGK 3901 Air Chent Admin AOLENT 1 MAINSD 20 03 2000 Playlist 1 Untheead E Ele ES Eyerts Resources Properties Toot Windom em Hep Damenn TERES TRS R DNIA iG e 10 0446 07 T 10 Example Playlist with secondary Data events of IS750 LGK 3901 Air Chent Admin 0L BENT 1 MAINSD 20 03 2000 Playlist 1 Untherad ER Ge ES Events Resources Properties Took window fem Help AmE u comm TEAS MRE RONG 3 ajaj _ oe fio130413 T 50 15796 00 l a 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 16 of 17 er Imagine User Notes Testing 1 Ensure that the serial RS 422 cable is attached to both the server and the device 2 Load a list into the Transmission window containing primary events with IDs matching the Name of the device and with a valid file number in the Title field 3 Make sure the device is properly set up from its control panel 4 Run the play list Error Conditions and Recovery If the devic e fails to communicate go to the Device Server and go through the following sequence of menus 1 Select the System Menu from the
3. 2D DVE and Easy Text control with Data Events with Data Commonly used DVE functionality is available in the form of Secondary A V events see the above description In addition the Imagestore driver and LGK 3901 driver support all of the discreet digital video effects commands and easy text commands These commands should be used as SECONDARY DATA EVENTS WITH DATA because the argument lengths are larger than the Title size The name of the command is entered in the Title field and the arguments in the External Data field separated by Enter The driver checks the format of the arguments but does not check the values range Please see the device user manual for more details about argument formats Command Description Arguments Title Field Data in Secondary Data Event with Data DVE SSP SetSqueezePreset Preset Xpos Ypos Xsize Ysize DVE SSC SelectSqueezeConfiguration ConfigurationMode DVE RSM RunSqueezeMove Preset Fields DVE SMP SelectMoveProfile Profile 0 linear 1 smoothed DVE SPB SelectPresetBorders PresetNo Left Right Top BottomBorder ET UTF UpdateTextField Layer BoxNo flags String ET CBSAP ChangeBoxSizeAndPosition Layer BoxNo X Y Width Height ET RB RenderBox Layer BoxNo ET Cl Changelmage Layer BoxNo NewLogo txt ET STFAC SetTextFontAndColour Layer BoxNo Size Col FontFileName ET ST SetTransparency Layer BoxNo Transparecny ET
4. range 0 thru 1 for Imagestore Driver lt Layer gt can be in range in range O thru 3 for Imagestore 750 Driver LKG 3901 Driver Suggested use of the new format for Title Field LIVE lt Layer gt lt Key Fill Pair Number gt Key Fill Pair number range is 1 thru 3 Note Miranda Device in use must support 3 Fill Key inputs Old Title field format can be used if Key Fill Pair Number 1 Provided Examples Old Format LIVE 2 Use Layer 2 and Fill Key pair with number 1 used with IS 750 M_LGK Devices Or New format LIVE 2 1 one space between 2 amp 1 LIVE 0 3 Used when user want to use Fill Key pair with a value more than 1 In this case only the new format will work In this example the Layer is O and the Key Fill pair is 3 Squeezy 2D DVE Automation with Secondary Data Events Several Secondary A V events have been defined to combine frequently used DVE commands into a single event SQM X Y Z Use this DVE event while the devcie is configured in Cascade Mode only This will be used when the currently on air background video is squeezed to reveal the Midground 0 logo buffer Parameter X is the pre defined squeeze move that is used at the beginning of the event and parameter Y is used at the end of the event e If parameter Zis provided the associated logo number is loaded onto layer 0 so that the logo will be revealed when the squeeze is played e If there is no Z provided the Live input is loaded t
5. should only be used for troubleshooting purposes 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 6 of 17 er Imagine User Notes M_LGK Channel 24 R Diagnostics e Device Reinitialize Cancel 7 When finished click Apply Assign the Device To a List To assign the LGK 3901 driver to a list do the following 1 From the Configuration utility right click on your Device Server and select List Configurations to display the List Assignments window 2 Locate the LGK 3901 driver in the Available Devices column Left click and drag it to the desired Transmission List in the Lists column Release the mouse when the pointer is over the Icon for the list Operation Notes As mentioned above the Imagestore and LGK 3091 drivers are only intended for use in Cascade mode If the device is set to Swap Preview mode when the driver is initialized this error will be logged MEDIA DEVICE NOT PROPERLY INITIALIZED This does not prevent operation in Swap Preview mode It is still possible to control the device in this mode using secondary data events The device responds to each command with an ACK acknowledgment that it received the command If the device does not ACK a command within five seconds or a NAK negative acknowledgment is received the command is resent 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 7 of 17 er Im
6. 7 er Imagine User Notes 33 14 55 20 16 LIST 1 A CUED _ fa fa SDK TEST __ 00 00 59 28 34 o0 60 00 00 is750_ sDAT PT Is750_ LOADI 3 Pizza __ 00 00 00 00_ 35 o0 00 10 00 fis750_ sDAT PT IS750_ _ PlayAnimation 3 _ 00 00 00 00_ 36 o0 00 30 00 is750_ sDAT PT IS750_ _ StopAnimation 3_ 00 00 00 00 _ 37 00 00 40 00___ I5750_ Ss sDAT PT__ is750 Restart nim 3 00 00 00 00 38 00 00 50 00___ I5750_ sDAT PT___ I5750_ StopAnimNow 3 00 00 00 00 _ Secondary A V format LIVE Alphanumeric file names are supported using the Play command When using A V events to recall Logo files each of the 16 heads for the ImageStore device correspond to one of the keyer layers head 1 is the midground layer and heads 2 through 16 are the foreground layers IMPORTANT All the functionality of ImageStore 750 is carried over to the Miranda LGK 3901 driver except the count of layers and heads ImageStore 750 has 4 layers And Miranda LGK 3901 has 3 layers There are two kinds of A V events Play and Live The format in the event s title field of each event type as follows Play lt LEVEL gt lt SPACE gt lt PagelD gt Where lt SPACE gt is an empty space between level and page s ID lt LEVEL gt is in 0 15 and lt PagelD gt is an alpha numerical string Live lt LEVEL gt Where lt LEVEL gt is in 0 1 The levels O and 1 are Imagestore Levels The levels from 2
7. NO DEVICE g6 Serial Devices 5 NO DEVICE 4 Switch Onlys 20 NO DEVICE Requesters 10 E3 Distributors 10 E Archives 2 FF 3 Select the M_LGK icon just created and press the right mouse button to bring up a menu Select Properties from this menu or double click on the icon instead 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 4 of 17 O Imagine User Notes 4 Click on the General tab M_LGK Channel 24 c Soe Device Name M_LGK ID Match Name M_LGK 7 Options a Back time value in frames 1 Guaranteed storage time 00 30 Configure the following parameters as required The Device Name will appear in the Device Status and configuration windows on the client applications The default name may be used but it is recommended to use unique names for easy identification later The ID Match Name will be used in the Transmission List s ID Field to let the system know that the event is intended for the device The Back Time value in frames determines when commands should be sent to the Imagestore A non zero value in this field indicates the number of frames that commands will be sent early during preroll before the play counter actually starts This value is set at 1 by default it shouldn t need to be changed However if the timing of the device is off with respect to the switcher t
8. STDS SetTextDropShadow Layer BoxNo Xoffset Yoffset Transparency Color ET STT SetTextTracking Layer BoxNo Tracking ET STA SetTextAlignment Layer BoxNo HAlign VAlign ET STW SetTextWrapping Layer BoxNo WrapMode ET STBC SetTextBackgroundToClear Layer BoxNo ET STBM SetTextBackgroundToMatte Layer BoxNo Col Trans HBorder VBorder ET STBTG SetTextBackgroundToGradient Layer BoxNo SourceCol DestCol BorderCol Trans BorderWidth Direction HBorder VBorder ET STBO SettingTemplateBackgroundOptions Layer Color Transp Mode EdgeSize 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 14 of 17 Imagine User Notes Command Description Arguments Title Field Data in Secondary Data Event with Data ET RS RunStrap Layer Start ET SSS SetStrapSpeed Layer Speed_PixelsLinesPerField ET TBU TextBoxUpdate Layer Field flags filename_strlen filename text ET IU ImageUpdate Layer Field filename_strlen filename image Example of Easy Text Playlist and According Trace Easy Text Playlist See m p e cl 00 00 00 00 Se ed ee ee a 00 00 10 00 00 00 00 00 00 00 00 00 sap iszso PLAY 2 S002 00 02 15 00 _ _ 00 00 00 00 sat JA fisz50 ETUTF 00 00 10 00 ____ oo 00 00 00 J JA Demo0004 Test audio type 00 00 10 00 00 00 00 00 pf ff tt jo0 00 00 00 DAT A aS is7s0 _ ee es er i ee l
9. agine User Notes If the device still doesn t respond correctly after two more failed attempts to communicate with the device the device status will change to NO DEV and an error will be logged that communication was lost with the device If this occurs the interface software tries to communicate with the device every five seconds when it gets a reply the status returns to UNTHREAD When the device receives a command it only verifies that the format of the command is correct and that the CRC is valid it does not check the validity of a command before returning an ACK Invalid commands or commands containing invalid file numbers will be ignored Animation Support The ImageStore 750 IS 750 and the LGK 3901 M_LGK driver support of Animation control Four Secondary Data Events were added to implement Animation commands Start Animation SO Stop Animation S1 0 Stop Animation Now S1 1 and Restart Animation S4 Important Enhanced animation control is only available in ADC v12 19 and above Imagestore and ADC v12 22 and above LGK 3901 It is not available in ADC v11 Animation Commands Start Animation SO Starts or restarts an animation playing out The animation starts playing from the current field To force playout from the beginning set the current field before issuing this command Stop Animation S1 e Stop Animation S1 0 The animation is halted If the complete cycle flag is set 0 the an
10. ayer number head number 1 2 box number 2 H p flag 1 e0 text contents Hello Traces Accordingly from ET playlist example B 031708_mod rxt notepad aT File Edit Format Yiew Help 52 30 33 33 3A AE R03S003 52 30 32 32 3A AE RO2SOO2 52 30 31 31 3A AE R015001 G 33 31 20 B1 lg 1i 5A 30 31 47 64 20 42 79 65 3A Z01021G00d Bye 24 33 32 20 F5 132 1i 5A 30 32 48 6C GF 3A 43 CC 1z02021HeT1o C 33 33 20 a9 133 1i 33 33 20 39 133 0 31 20 21 31 0 0 SMM NM NM OM MOM OM OM OMS MMMM MMMM 32 20 65 132 a 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 15 of 17 S Imagine User Notes COMMI TIONS Example of secondary event of IS750 LGK 3901 Example Playlist with secondary AV events of IS750 LGK 3901 Example of DSK 1 as Layer 1 DSK 2 as Layer 2 and DSK 3 as Layer 3 with IS 750 LGK 3901 00 00 0060 S S E ret sa ype Jonson 0 00 o0 00 00 00 Jav PT isz50 PLAY s002 00 00 20 00 oo o0 00 00 JA Demo0004 Test audio type 00 00 10 00 o0 00 00 00 sv JPT isz50 PLAY S003 _ 00 00 20 00 oo 00 00 00 JA Demo0005 _ Testaudiotype 00 00 10 00 00 00 00 00 J Jev Pr isz5o PLAY 5123 00 00 20 00 oo 00 00 00 JA Demo0006 Test audiotype 00 00 10 00 jo0 00 00 00 Ts fpr fisz50 Play sdre06__ 00 00 20 00 oo o0 00 00 JA Demo0007 Test audio type
11. between the card and the Co Processor and from the panel set the protocol and baud rate for the serial port as follows 1 These settings are made from the system menu to get to this menu select the set up menu from the front panel and press ENTER the bottom key on the panel Select system from the menu that appears next the device prompts with a system change NO YES display select YES to continue First set the device for Cascade mode Select the swap PVW cascade item choose the cascade option and press ENTER The device must be set up for RS422 control Select the serial protocol menu item then choose RS422 and press ENTER Set the baud rate to 19 200 The protocol should be set to strict and not relaxed on the SD models on the HD model set the protocol to automation On the front panel under SETUP gt SERIAL COMMS gt SERIAL PORTS gt COM 1 2 gt PROTOCOL gt INTUITION On the front panel under SETUP gt SERIAL COMMS gt SERIAL PORTS gt COM 1 2 gt BAUD RATE gt 19200 Cable Requirements The following image represents the back plane of an LGK 3901 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 2 of 17 cy Imagine User Notes COM 1 COM2 port COM 1is an RJ45 port that provides serial bidirectional communications to external Automation systems EAS units LGK 3901 only with LGK 3901 OPT EAS or a slave Intuition
12. d sent to the device or literal strings that are sent directly to the device Pre defined Commands All of the pre defined commands can be sent to either of the two keyer layers independently The keyer layer is selected by adding a colon to the end of the command followed by a 0 or a 1 Layer 0 is the midground layer and layer 1 is the foreground layer If a layer isn t specified it defaults to layer 1 Not all commands are valid for both levels and the valid commands change according to the Imagestore s mode Reference Note Consult the Imagestore or LGK 3901 User s manual for more information CTB Cut layer to black CFB Cut layer from black CUP Cut keyer up CDN Cut keyer down FFB Fade layer from black FTB Fade layer to black FUP Fade keyer up FDN Fade keyer down GRAB Grabs a frame from the key and fill input signals 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 12 of 17 er Imagine User Notes KLR Set key linear KFL Set key full KNL Set key normal KIV Set key invert LOAD Load a file number on the specified layer The file number to load follows this command E g LOAD 0 7 loads file number 7 on the midground layer LOADI Load a file name on the specified layer The file name to load follows this command E g LOADI 0 bug loads file with name bug on the midground layer LIVE Load a live key l e use the si
13. er Imagine User Notes Product ADC v12 Topic Miranda LGK 3901 The LGK 3901 Logo Inserter amp Downstream Keyer a variant of the IS 750 is a low cost modular channel branding processor capable of inserting up to five layers of graphics into 3Gbps HD SD Three of the keying layers can be fed by internally stored still animated graphics and two layers are fed by external graphics devices The LGK 3901 is ideal for pre rendered graphics Support for 3 layers only The LGK 3901 driver is based on the driver for the ImageStore 750 All the functionality of ImageStore 750 is carried over to the Miranda LGK 3901 driver except the count of layers and heads ImageStore 750 has 4 layers And Miranda LGK 3901 has 3 layers Driver Limitations ADC is unable to control the PresMaster MCS through any of its ImageStore drivers including the IS 750 and LGK 3901 Control of the Easy Sound option has not been implemented The Storage Check functionality was not tested and is not supported Release Date 9 December 2014 Revision History Revision Protocol Date Author Company Description 1 1 31 14 Initial Version Used Firmware Protocol 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 1 of 17 oS Imagine User Notes Device Settings To configure an LGK 3901 DSK 3901 to forward commands onto a Graphics Co Processor connect a serial link
14. gnals present on the key and fill inputs for the key on the specified layer ULIVE Unload the live key If an internal file was previously loaded on the given layer that file will be restored The live key will also be unloaded if another internal file is loaded on the same layer SFK Set self key SPK Set separate key STR Set transition rates for a layer This command takes two additional parameters The first parameter contains two characters describing which fade rate type will be modified the second parameter is a number between 1 and 99 giving the number of frames for the new fade rate Parameters are separated by spaces The fade rate types are e FK Change the keyer fade rate e FB Change the fade to black rate e SL Change the slide rate The two commands below don t actually cause a command to be sent to the device Instead they change the transition type for primary and secondary A V events SETCUT Set the transition type to Cut the default SETFADE Set the transition type to Fade Examples FTB 0 Fades keyer level 0 to black CUP or CUP 1 Cuts the key in for level 1 STR 0 FK 60 Changes the key fade rate to 60 frames for layer O SETFADE 0 Subsequent primary or secondary A V events played on layer 0 head 1 will fade on and off 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 13 of 17 cy Imagine User Notes Squeezy
15. guration changes made upon the various tabs will be applied however the configuration window will close Press Cancel and none of the configuration changes will be applied to the driver and the configuration window will close Device Driver Configuration Still Store To configure the Still Store driver for Imagestore on the Device Server follow the procedure below 1 From the Configuration utility right click on your Device Server icon and select the Configured Devices item to display the Configured Devices window 2 From the list in the right hand pane select MIRANDA LGK 3901 from the Still Stores category Use the mouse pointer to drag this item over the top of one of the icons in the left hand pane that has the caption NO DEVICE as shown below Configured Devices SERVER20 File Edit View Help Configured l Available Device Channel E Evertz 9625 LGA DSK Stand alone Demo Video D Channel 22 r Miranda Intuition Image Store NO DEVICE Channel 23 H Haris DTP20 Miranda LGK 3901 Phannel 24 Bl SAV LG50DK Logo Generator NO DEVICE W Pixel Power Clarity NO DEVICE jal VSM SubDev E Evertz9725LGA 16 char logo names NO DEVICE f NO DEVICE H Harris mCapture NO DEVICE i EvertzOme for DVE amp Logo W Miranda Imgstore750 NO DEVICE MF Miranda LGk 3901 NO DEVICE H Harris AMP Logo NO DEVICE fl Harris IconStation XML NO DEVICE fl Maestro Sub Device NO DEVICE eS Character Generators 4 NO DEVICE EA Audio Disk Carts 4
16. his parameter may be changed to adjust the output timing This parameter does not change the timing for secondary data commands The Storage Check setting when enabled this will allow Device Server to check on the availability of an ID prior to registering it within the ADC Transmission List Guaranteed storage time This parameter is available when Storage Check is enabled This parameter specifies the time MM SS during which media will not change i e it is the interval of recheck events in a playlist Default 30 seconds Range 10 99 Recommended Specification for this parameters should be a multiple of 10 seconds 5 Select the Serial Port tab 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 5 of 17 O Imagine User Notes M_LGK Channel 24 A Serial Port Diagnostics RY No Port OK Cancel Configure the physical serial port number Choose Serial Port in drop down list This port selected is physical port which the Imagestore 750 is connected to When viewing the serial port cards on the back of the ADC Device Server the upper left serial port is Port 1 The port numbers increase as you count down the ADC serial board The top serial port of the next serial card will be the following port number 6 The Diagnostics tab This tab contains a Reinitialize button which will clean the buffers in the driver and reset the connection to the Imagestore This
17. imation completes its cycle before halting In some animations this may cause a special stop section of the animation to execute e Stop Animation Now S1 1 The animation is halted If the immediate flag is set 1 then animation halts immediately at the specified frame Animations always halt showing two frames to form a field If there is much interfield motion the image will flicker Restart Animation S4 Always restarts an animation playing out from the beginning This command is a convenient alternative to the SO command when the animation has to always start from the first field Format Title field The Format Title field for these command is PlayAnimation lt Layer gt StopAnimation lt Layer gt 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 8 of 17 Imagine User Notes StopAnimNow lt Layer gt ReStartAnim lt Layer gt Where lt Layer gt should be in range 0 3 AUTOMATION Either primary or secondary events may be played on the device When using primary events you must configure the AUDIO VIDEO parameters for the heads as with other devices If the output of the device is not being used as a primary video feed but as possibly a key then both a secondary key event and secondary Audio Video event are required For the device to play a list event the ID field of the event must match the device name for the still store device For Primary Secondary A V and Bac
18. ktimed A V events the Title field of the event will contain either the file number still to be loaded from the devcie or it may contain the word Live to play the image present on the key and fill inputs Files are named Vnnn OXT for stills or Vnnn OXA animations in the Miranda media software however the files are referred to by just their number nnn ADC software the leading V and file extension are omitted in the playlist The format of the event s title will be different between secAV and secData events The formats and samples of the events will be provided in each section of the event types Device Server supports Restart Animation Start Animation and Stop Animation commands This also applies to playing internal Audio Files For new secondary data events To support the commands with the IS 750 and LGK 3901 drivers four types of the Secondary Data Events were added to the list of supported commands The Title field within the ADC Transmission List for the new sDAT commands should be 1 Start Animation PlayAnimation lt Layer gt 2 Stop Animation Complete cycle then stop StopAnimation lt Layer gt 3 Stop Animation Immediate stop StopAnimNow lt Layer gt 4 Restart Animation RestartAnim lt Layer gt Where lt Layer gt Integer in the Range 0 3 Playlist Example using the new sDAT Animation control 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 9 of 1
19. main menu bar 2 Select the Diagnostics item from the System menu 3 Select the device and choose Reinitialize If this fails to solve the problem check the cables Verify that the cable conforms to the specification given earlier in this document and that all the signal lines are good Test the device operation manually through its control panel check its configuration or power it off then wait twenty seconds and power back on If the device still fails to communicate you may have a problem with the device itself If this is the first time you ve attempted to use this device the device may have some internal jumpers set incorrectly for RS422 communications or there may be an actual hardware error Contact Miranda for assistance in North America Internal Document File XXXXX XXXXX 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 17 of 17
20. o layer 0 SQF X Y Z Use this DVE event while the device is configured in Cascade Mode only This will be used when the currently on air background video is squeezed to reveal the Foreground 1 logo buffer Parameter X is the pre defined squeeze move that is used at the beginning of the event and parameter Y is used at the end of the event e If parameter Zis provided the associated logo number is loaded onto layer 1 so that the logo will be revealed when the squeeze is played 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 11 of 17 er Imagine User Notes e If there is no Z provided the Live input is loaded to layer 1 SQB X Y Both Swap Preview and Cascade Modes This will be used when the On Air Background A Input is squeezed back to reveal the other not on air B Input Secondary Data Commands Secondary data events may be used to send commands for a particular layer directly to the device If a start time is not given for a Secondary data event the command is sent to the device when the associated primary event plays If a start time is specified the time is used as an offset from the start time of the primary event For secondary data events head 1 is the midground layer and head 2 is the foreground layer i e independent of primary or secondary A V events They may be sent while other events are playing These events may contain pre defined commands that are translated an
21. to 15 correspond to levels from 0 to 13 of Intuition There is the difference in playing logo files on Imagestore and on Intuition devices To recall the file on Imagestore you should just use the PLAY command with level 0 or 1 To Recall files on Imtuition Device you should send the LIVE command first with Level 0 or 1 Until then this command will not be carried out you can send to different Intuition levels the command PLAY A command is sent to load the desired still or switch to the live signal when the event is cued This occurs when an event comes into the look ahead count and a head is free to play the event When the event actually plays the keyer for that layer is turned on when it finishes playing the keyer is turned off The still will remain loaded on the keyer layer until another event is cued on the corresponding head or a secondary data event loads another still Secondary Data Events may also be used to control the Logo file recall functionality This is described below The Imagestore and Imagestore750 drivers support the additional selection of Fill Key pairings A new format is used within the Title Field of the Secondary Data Event however the previous format is also supported Suggested use of the old format for Title Field 2014 Imagine Communications Corp Proprietary and Confidential 9 December 2014 Page 10 of 17 er Imagine User Notes LIVE lt Layer gt Where lt Layer gt can be in
Download Pdf Manuals
Related Search