ICM-02 - Austin Hughes
Contents
1. address is in the network it may cause such problem ii Disconnect the Master IP fan unit from the network and try to direct connect the Cat 5 6 cable from the lt IP gt port to a computer network port and use IP Setup utilities to check if the Master IP fan unit can be found or not If it cannot be found the Master IP fan unit may be failed TRS ICM 02 Q313V2 Fal www austin hughes com Replacement removal or addition for remote FAN unit 1 How to replace the failed Master IP fan unit with a new one Step 1 Prepare a new Master IP fan unit and set it to 1st level Please refer to user manual lt 2 5 gt for the fan unit level setting Step 2 Disable alarm email in lt Alarm gt page Step 3 Power off amp remove the failed Master IP fan unit from connection Step 4 Install the new Master IP fan unit to the connection amp power it on Step 5 Click Start Connection in lt Status gt page for the relevant Master IP Group Step 6 Configure the new Master IP fan unit in lt Details gt amp lt Temp sensor gt page such as Rack Position Alarm Temp Step 7 Enable alarm email in lt Alarm gt page 2 How to replace a failed certain level remote fan unit with a new one Step 1 Prepare a new remote fan unit and set the remote fan unit level accordingly Please refer to user manual lt 2 5 gt for the fan unit level setting Step 2 Prepare an appropriate length Cat 5 6 cable S2. Troubleshooting FAN unit disconnection 1 GUI shows a certain level remote fan unit disconnected Except Master IP fan unit Step 1 Remote fan unit power off Check the remote fan unit is power ON or not Step 2 Fan unit level setting duplicated in the same Master IP group Check and make sure fan unit level is unique and not duplicated in the same Master IP group Please refer to user manual lt 2 5 gt for the fan unit level setting 2 GUI shows disconnected Except Master IP fan unit Step 1 Cable disconnected loose or defective Check the Cat 5 6 cable connection between remote fan units Make sure the connectors are firmly attached And check if any defects on your cables or not If yes replace a new one Step 2 The first disconnected remote fan unit failed Unplug the Cat 5 6 cable on the first disconnected remote fan unit then plug it to the second disconnected remote fan unit to check if the problem caused by the first disconnected remote fan unit 3 GUI shows the whole group of remote fan unit s disconnected Step 1 Cable disconnected loose or defective Check the Cat 5 6 cable connection to remote fan units and network devices Make sure the connectors are firmly attached And check if any defects on your cable or not If yes replace a new one Step 2 Master IP fan unit failed i Check if the network setting of the Master IP fan unit is correct or not If duplicate IP
3. he removed fan unit is in the last level 4 How to add an extra remote fan unit to an existing fan unit group Step 1 Prepare a new remote fan unit and set the remote fan unit level accordingly Please refer to user manual lt 2 5 gt for the fan unit level setting Step 2 Prepare an appropriate length Cat 5 6 cable Step 3 Click Set maintenance in lt Details gt page for the affected remote fan unit s which next to the added remote fan unit Step 4 Install connect and power on the new remote fan unit Step 5 Reconfigure amp reset the level for the affected remote fan unit s which next to the added remote fan unit Step 6 Click Remove maintenance in lt Details gt page for the affected remote fan unit s Step 7 Click Search in lt Status gt page to search the new installed remote fan unit Step 8 Configure the new remote fan unit in lt Details gt amp lt Temp sensor gt page such as Rack Position Alarm Temp A Ignore step 3 5 amp 6 if the added remote fan unit is in the last level TRS ICM 02 Q313V2 P 3 www austin hughes com InfraCool Manager ICM 02 1 Try to login InfraCool Manager ICM 02 but the web browser only shows HTTP 404 Not Found Step 1 Services for Web server in management PC started Make sure the services is started Go to Control Panel gt Administrative Tools gt Services gt Apache2 2 and make sure the status is Started Step 2 Por
4. t for web server in management PC is occupied by other service Check if the port for web server is used by other service If yes please release the port of that particular service and assign another port for it Step 3 Port for web server is added in the firewall of management PC Check if the port is added in the firewall If not please add and enable the connection in the firewall Please refer to user manual lt 4 2 gt for details TRS ICM 02 Q313V2 P 4 www austin hughes com
5. tep 3 Click Set maintenance in lt Details gt page for the failed remote fan unit Step 4 Use a Cat 5 6 cable to bridge over the failed remote fan unit which will be replaced to minimize log data loss Step 5 Power off amp remove the failed remote fan unit from connection Step 6 Install the new remote fan unit cancel the cable bridging and reconnect the remote fan unit to the last and next one Step 7 Power on the new remote fan unit Step 8 Click Remove maintenance in lt Details gt page for the new remote fan unit Step 9 Configure the new remote fan unit in lt Details gt amp lt Temp sensor gt page such as Rack Position Alarm Temp A Ignore step 2 amp 4 if the failed remote fan unit is in the last level TRS ICM 02 Q313V2 P 2 www austin hughes com Replacement removal or addition for remote FAN unit 3 How to move out a remote fan unit without a replacement Step 1 Prepare an appropriate length Cat 5 6 cable Step 2 Click Disable monitoring in lt Details gt page to stop monitoring the removed remote fan unit Step 3 Use the Cat 5 6 cable to bridge over the removed remote fan unit to minimize log data loss Step 4 Power off amp remove the fan unit from connection If the removed remote fan unit in the last level you reconfigure and reset the level for the affected remote fan unit s which next to the removed remote fan unit p A Ignore step 1 amp 3 if t
Download Pdf Manuals
Related Search