ShowTex User Manual TMC DMX Pro
Contents
1. ITEM WEKELIJKS 6 MAANDEN Check that the curtain tracks are operating smoothly Inspect condition of operatingdine Inspect operating line tension Listen for unusual pulley noise The above maintenance schedule is recommended for normal operating conditions Within 24 hours of using a recently installed system confirm that the rope tension is at correct level for curtain movement Above average use or location of curtain track in places with high humidity dust extreme temperature changes etc may require shorter intervals Take the system down following the same steps and precautions as during installation 14 ShowTex User Manual TMC DMX Pro Trouble Shooting What to do if the curtain stops moving smoothly Check for damage to the track If found repair Check that all couplings are lined up without gaps If necessary realign Joints between track should not be too loose or too tight to avoid a bowed track Check for damage to runners If necessary replace damaged runners If your track has a switching point check that all parts are lined up correctly If not adjust alignment Check for debris on the track or runners if found remove carefully If the curtain slides out of the track check if the end stops are loose or missing If necessary tighten or replace In case of power failure the motor can be detached by loosening the bolt of the hand wheel to switch to manual wheel operation For more2. requires 3 DMX channels Channel 1 and 2 determine the position of the curtain Channel 3 controls the curtain s speed of motion Dn gt ry Next set the correct DMX address by pressing on the button andthe button until DMX address appears on screen use the and buttons to adjust the DMX address v Press the button to confirmwhen you have arrived at the desired address The DMX mill adress is now programmed DMA control 17 Switch the TMC DMX Pro to DMX contro Use the remote control unit to switch the TMC DMX Pro system to DMX control ShowTex User Manual TMC DMX Pro 13 Care and Maintenance The TMC system has components that must be regularly checked maintained and replaced in order to ensure safety and keep it in good condition The best way to maintain the TMC system is to use it often Each mechanical part should be used at least once a week In this way irregular noises can be discovered in time Do not allow any item to be operated or used if there is any question as to its safety or integrity Accidents and injuries can be the result Most accidents are the result of lack of training complacency and overconfidence Do not assume anything Follow the schedule outlined below as a minimum maintenance program Once the operating personnel has had an opportunity to work with thesystem during the first year additional procedures may be added or adjusted as is necessary depending on your facility requirements
3. d controller allows for fast motion with avariable speed 6f0 to 80 cm sec The TMC DMX Pro system makes it possible to open and close curtains manually and through DMX control The system can be partially integrated into the show by setting 2 DMX channels Channel 1 opens the curtain and channel 2 closes the curtain Speed can b controlled through a remote control unit The TMC system is compatible with the ShowTex H100 Showpipe 3 way UniTrack and ShowTrack track systems ShowTex User Manual TMC DMX Pro 03 safety Instructions Read this user manual carefully The motion system may only be used to move curtains and screens Never use this system to move people animals or any other heavy objects Installation and service of the units should only be carried out by qualified technicians familiar with the system and its operation Installation and operation must take place ina dry frost free environment To prevent electrocution and contact with moving parts disable the power supply be fore carrying out any work on the units including butnot limited to operating line and curtain mounting or removal of the casing or cowling A sudden unexpected start up of the system by not disabling the power in both the standard and DMX units creates a risk to the operator Units must be installed with a corresponding earth wire with the same section as the power cable 04 ShowTex User Manual TMC DMX Pro Component Parts The TMC DMX Pro sys
4. er Loosen the two M6 socket head screws with the socket head wrench 2 Next remove the aluminum operating line guide plate ShowTex User Manual TMC DMX Pro 07 Assembly 3 Thread the operating line 6 7 08 ShowTex User Manual TMC DMX Pro Place the operating line over the left right guide wheel that serves as a guide pulley Place the operating line over the tightening wheel on the bottom left right side Place the operating line between the belt and the wheel while staying inside the operating linegquide groove Then turn the hand wheel clockwise until the operating line appears on the otherside Secure the guide plate in the correct position Thread the operating line further through the track as instructed Thread the operating line through the ball raced runners Through the return pulley and pilot release Make sure the springs are completely tensioned Secure the protective cover in the correct position Assembly 4 Install the limit switches Attach the two limit switches including the installation plate to the track on the posi tions where the curtains should stop Attention The limit switches must be installed before starting up the unit to prevent motor blockage or slippage resulting in system damage Connect the remote control to the control panel The remote control makes it simple to use and program the units however it s not essential for operation of the unit When working solely
5. ice Scandinavia M 46768936 632 F 31 35 693 87 55 info scan8showtex com gt Sales Office North Africa M 212 6 4817 6909 F 32 3 236 23 02 Morocco info naGshowtex com Nae IA www showtex com
6. sShowltex User Manual TMC DMX Pro A Showlex AMAZING STAGE FABRICS IN MOTION Introduction Safety Instructions Components Assembly 10 11 12 13 14 15 16 17 Table of Contents Secure the motor to the track Remove the motor s protective cover and operatingNine guide plate Thread the operating line Install the limit switches Install the control panel Connect the motor to the control panel Connect the remote control to the control panel Connect the limit switches to the control panel Connect the control panel to the power outlet Switch the TMC DMX Pro to manual control option Test the position of the limit switches Test the general operation of the TMC system Hang the curtain Set the soft limits 14 1 Setup with the remote control 14 27 Set up with the keypad on the control panel Connect the DMX cable to the control panel Program the DMX channels Switch the TMC DMX Pro to DMX control Care and Maintenance Instructions Trouble shooting 02 ShowTex User Manual TMC DMX Pro 03 04 05 07 07 07 08 09 09 09 09 11 12 Introduction The TMC DMX Pro system facilitates computerized motion control of curtains and set pieces along a motorized track system The operating line and head pulley guarantee maximum grip for extremely accurate movement The TMC DMxX Pro system is equipped with an easy to use remote control with 370W open close switch and speed controller The spee
7. technical assistance please contact your local ShowTex office see back cover of manual HAVE A GREAT SHOW ShowTex User Manual TMC DMX Pro 15 gt gt ShowTex Belgie nv Hoofdkantoor Everaertsstraat 69 B 2060 Antwerpen Belgi T 32 3 236 84 40 F 32 3 236 23 02 info be showtex com ShowTex Belgique sa T 32 10243500 F 32 10 24 3600 info be showtex com gt gt ShowTex France 16 PI G n ral De Gaulle F 59800 Lille France T 33 0 3 20 63 73 60 F 33 0 3 20 63 73 61 M 33 0 6 89 62 59 90 info fr showtex com gt gt ShowTex Nederland bv Energieweg 2b 3762 ET Soest Nederland Postbus 31 3760 AA Soest Nederland T 31 35 693 8692 F 31 35693 87 55 info nIGshowtex com rental nl amp showtex com gt gt ShowTex Middle East FZ C Sharjah Airport Free Zone Warehouse 04 lt 79 80 P O Box 120226 United Arab Emirates 1 971 6 557 98 00 F 971 6557 98 10 info meQshowtexcom gt gt ShowTex Hong Kongtd Units D F 10th Fl or Wing S ha industriaMBuilding 428 Cha Kwo Ling Road Yau Tong Kowloon HongKong T 852 2727 7558 F 852 2727 7920 info hkesHowtex com gt ShowTex South Africa pty Union Textile Building Perth Road Maitland Cape Town Western Cape 7451 South Africar 1427 82 453 7488 F 27 86 689 1535 info sa showtex com gt gt Sales Office UK T 44 170 681 97 46 M 44 776 534 1878 E 323 236 23 02 UK info uk showtex com gt gt Sales Off
8. tem consists of the following parts TMC DMX Pro System Controller Remote Unit TMC Power Supply Cable Limit Switch Set Cable 3G 0 75 XLR 3 Male Plug Naam Art nr information TMC DMX Pro controller 8050 0741 3707 370W Remote Unit TMC 8050 0766 0030 with 25m cable Power Supply Cable 8150 0912 0027 Limit Switch Set 8050 0770 0050 2 pieces Cable 3G 0 75 0350 0101 5000 25m XLR 3 Male Plug 0360 0003 0010 Extra tools Socket head wrench M6 ShowTex User Manual TMC DMX Pro 05 specifications Single phase power supply 2x 230Vac earthing Speed of rotation 50 Hz 35m min Height 460 mm Width 210mm Depth 350 mm Operating line Diameter 8mm Motor 0 37 KW l 1 10 N2 138tr min EElectrical case to hang up with the cord unit with Nord Invester SK 500E 370 323 A with a 370 Watt capacity Dmx Uss link via standard Dmx channels 06 ShowTex User Manual TMC DMX Pro Assembly In order for the system to operate correctly the following steps should be taken securing the motor to the track Connect the motor to the track Attention Runners and ball raced runners should already be installed in the track The motor is compatible with the H100 Showpipe 3 way Unitrack ShowTrack track systems from ShowTex For track installation instructions please refer to individual track manuals 2 Remove the motor s protective cover and operating line guide plate 1 Remove the protective cov
9. through DMX channels and DMX keyboard always use a dummy plug in the remote control outlet to ensure the unit remains in DMX mode ShowTex User Manual TMC DMX Pro 09 Assembly 8 Connect the limit switches to the control panel Connect the two limit switches to the control panel using the 3G 0 75 cable Plug the 3p XLR end plug in the Endstop Input outlet of the control panel Attention Ensure that any extra cable can t get in the way of operation by attaching it to the suspension pipe with tape cable straps or B2B Velcro Plug the power cable into the Power Input 220Vac outlet of the control board and then connect it to the power supply Attention All connections must take place before powering up the unit Unplug from the power supply before any maintenance to the unit Use the remote control unit to switch the TMC DMX Pro system to the manual control Option 10 ShowTex User Manual TMC DMX Pro Assembly 1 I rest the position of the limit switches Manually test the position of the limit switches by testing which direction of motion will cause the curtain to stop If necessary change the position of the limit switches Attention To prevent damage to the unit never allow the master carriers to move be yond the end stops Test the general operation of the TMC system Confirm that the Operating line is ten sioned correctly by confirming that the springs are adequately tensioned icem Hang the c
10. urtain eae 1 47 A de ShowTex User Manual TMC DMX Pro 11 Assembly 14 Set the soft limits 14 1 set up with the remote control Track Motor Control DMX Pro 506 OPEN CLOSE STORE ENTER Use the OPEN CLOSE button on the remote control to close the curtain Now push the STORE button blue and keep it pressed in Confirm this position by briefly pressing the ENTER button green Next open the curtain without releasing the STORE button When the curtain is in the desired position press the ENTER button again briefly Then you can release the STORE button Both soft limits are now set at the correct position 14 2 sei up with the keypad on the control panel Track Motor Control DMX Pro 508 q p OPEN CLOSE STORE ENTER e gt A a v DMX control I Use the DPEN CLOSE button on the remote control to close the curtain 2 Press or P onthe control panel until soft limit min appears onscreen Then press and at the same time and confirm by pressing lt 3 Next press for i until soft limit max appears on screen then press lt and 4 atthe same time and confirm by pressing lt Both soft limits are now set in the correct position 12 ShowTex User Manual TMC DMX Pro Assembly 15 Connect the DMX cable to the control panel Connect the DMX cable of the motor to the control panel 16 Program the DMX channels The system
Download Pdf Manuals
Related Search