ECO Spot™ LED80E User Manual
Contents
1. recommended gobo image diameter is 35mm An Image Diameter of up to 40mm is possible with some loss in focusing quality Unscrew the thumbscrews to remove the front cover with the projection lens Push the two pins of the gobo retaining ring together and pull out the retaining ring Carefully remove the old gobo and replace it with the new gobo Tip Tilt the projector forward while placing the palm of your hand inside the old gobo will fall into your hand If you have a glass gobo place the more reflective side towards the light bulb Replace the retaining ring and make sure it evenly pushes the gobo all the way back Replace the front cover and adjust the focus by threading the projection lens in or out Copyright 2013 Globus New Media LLC Page 3 ECO Spot LED80E User Manual Voltage IP Ratings 100 240V 50 60Hz 0 9A 90W and 277V 50 60Hz 0 5A 9OW US only LED Driver IP66 Fixture IP 55 Ambient Operating Temperature 13 to 104 F 25 to 40 C LED Bulb Luminous Flux Dimmable Dimensions Fixture Body Total Length Yoke Base Yoke Height Total Height Weight Gobo Size Gobo Types 80W 50 000 hours 5 500k 500 1 000k 8 000Im 2 700lm effective Not dimmable 7 5in x 5 5in x 14 5in 190mm x 140mm x 370mm 18in 460mm with 25deg lens 20in 510mm with 15 deg lens 6 4in x 7 8in 163 x 198mm 7 5in 190mm from base to center 10in 254mm from base to top Pro2. ECO Spot LED80E User Manual ECO Spot LED80E User Manual The ECO Spot LED80E is intended for exterior and interior applications Thank you for choosing an ECO Spot Gobo projector This unit is equipped with a fan cooled heat pipe to keep the 80W High Power LED running cool Please read this manual before installing or operating this fixture follow the safety precautions listed below and observe all warnings WARNING To prevent damage to the LED always connect the driver to the projector FIRST before powering up the driver Package Contents v Projector with Projection Lens v External LED Driver A Test Gobo mounted lt Thread ring with silicone seal for the projection lens Safety Information Place your fixture at a suitable place with good air flow Keep flammable materials away from the fixture Minimum distance to flammable material 1 ft 0 3m Minimum distance to illuminated surface 3 3 ft 1 0m Provide a minimum clearance of 4 in 10cm around air vents Use only genuine spare parts for part replacement Do not look directly into the lamp it can result in eye damage Always unplug the unit from the power mains before any service is done Light fixtures should be installed and maintained only by qualified personnel with experience in lighting equipment and general electrical experience Disconnect the fixture from AC power before handling the fixture Always ground earth the fixture electric
3. ally Use only a power source that complies with local building and electrical codes and has both overload and ground fault protection Do not use the fixture if the power cable or power plug is in any way damaged defective or wet or if they show signs of overheating Copyright 2013 Globus New Media LLC Page 1 ECO Spot LED80E User Manual Handling Instructions There is a weatherproof connector between the driver power supply and projector which can be opened for easier handling Always make this connection first before powering up the driver otherwise the LED can be damaged by the power surge Before the initial start up please unpack and carefully check for damage caused during transportation Place your fixture at a suitable place with good air flow Make sure there are no flammable materials close to the lamp When suspending the fixture above ground level verify that the structure can hold at least 10 times the weight of all installed devices Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable Warranty One Year from Date of Purchase Keep your receipt for reference and contact your dealer in case of warranty issues Projection Lenses The projector accommodates interchangeable projection lenses to allow optimizing the projection size and resulting brightness at varying distances The more narrow the
4. jector 11lbs 5kg Driver Power Supply 1 3lbs 0 6kg M size OD66mm x ID48mm up to 4mm thick Glass Metal Plastic gobos up to 8 hours Typical Range The range varies greatly with the application and ambient light situation typical values 6 to 32 ft in bright environments upto 64 ft in dim environments upto 112 ft in dark Projection Lenses The fixture comes with one lens included Available lenses are e 25 degree Medium Wide 20 degree Medium 15 degree Medium Narrow Page 4 Copyright 2013 Globus New Media LLC
5. lens the smaller and brighter the image will be at a given distance For example cutting the projection size in half will quadruple its brightness Gobo Rotator If the fixture is equipped with a gobo rotator it can be turned on off with the silver push button on the front plate underneath the lens There are no controls for rotating speed or direction Power up the projector e Ifthe fixture is equipped with a gobo rotator turn it on and then off again once the gobo projects in the desired position Loosen the outer ring around the lens that acts as a water seal Focus the projection by twisting the lens in and out until the image is well focused When used for the first time the lens will often need to be twisted outwards many rotations to reach the focusing point When in doubt keep going Re tighten the outer ring with the seal to ensure the lens won t leak water Page 2 Copyright 2013 Globus New Media LLC ECO Spot LED80E User Manual Multi functional Yoke The yoke can slide over the whole length of the fixture body to accommodate a wide range of pointing directions The yoke can also serve as stand The yoke can be screwed to a wall or ceiling or fastened with a C clamp Gobo Placement see Specifications for Gobo dimensions The ES LED40E can accommodate two different gobo sizes E Size and D Size See the Specifications for exact dimensions For max image size and brightness use the larger gobos The
Download Pdf Manuals
Related Search