w, User Manual I
Contents
1. GSM POWER SOCKET USER MANUAL 3 12 Resetting the socket Description e _ This function resets all programmed settings to their original values including cleaning all user number timing parameter and temperature parameter e If the setting status is wrong or the malfunctions can t be corrected users can restore the socket to its original status to make it work normally a Note This function needs to be used carefully as it also erases all setting values Method Method 1 Press the side M button of the device for 5 seconds Method 2 The Master user sends following SMS message to GSM Power Socket in order to Reset the socket 08 43 Successful SMS reply Reset the socket to factory setting successfully A long Beep tone if enabled will be heard and it means resetting the socket successfully 32 GSM POWER SOCKET USER MANUAL Chapter 4 Maintenance e f GSM Power Socket does not in use for long time it should be powered off e Store and use the remote socket in suitable temperature Too high or too low temperature will likely to damage the socket e Try to keep the GSM Power Socket and all its accessories dry Do not store and use it in the bathroom or other place with high humidity Do not allow pour water or other liquids into the socket otherwise it might cause malfunctions e Do not store and use the socket in dusty e Do not use alcohol acetone and other similar solvents to clean2. 28 160 Temp Time Disable the temperature rapid changing alarm 29 160 0 SMS notification upon the socket output changing Default No SMS notification upon the socket output changing 38 SMS notification 11 1 wo 31 11 0 Category Beep warning tone Check status Reset to factory settings GSM POWER SOCKET USER MANUAL Function Command SMS notification upon the power supply changing 32 12 1 Default No SMS notification upon the 33 12 0 power supply changing Enable the Beep warning 34 19 1 tone Disaable the Beep warning tone Default sin alec Check socket operating 36 07 status Check Socket output status 37 000 Check Delayed switch on off the socket parameters 38 1382 Check Timed switch on the socket parameters 39 1284 Check Temperature control parameters i 40 159 41 160 42 170 Reset the socket 43 08 Check temperature rapid changing alarm parameters Check over temperature alarm parameters
3. Check Timing switch on the socket parameters 128 39 After receiving the SMS commands GSM Power Socket will reply one 30 GSM POWER SOCKET USER MANUAL SMS message of Timing switch on the socket parameters Schedule control function ON OFF WorkDay StartTime EndTime Check Temperature control parameters 159 40 After receiving the SMS commands GSM Power Socket will reply one SMS message of temperature parameters checking Status ON OFF Temp control function ON OFF Temp Mode Heating Cooling Range LowTemp HighTemp If No temperature sensor connected be received it means GSM Power Socket cannot detect the temperature sensor User needs to check if the temperature sensor is inserted to the I O port Check temperature rapid changing alarm parameters 160 41 After receiving the SMS commands GSM Power Socket will reply one SMS message of parameters It means SMS alarm message will be sent upon the surrounding temperature changes Delta centigrade degree within minutes Fast temperature changing function ON OFF Delta Time minutes Check over temperature alarm limits parameters 170 42 After receiving the SMS commands GSM Power Socket will reply one SMS message of parameters It means SMS alarm message will be sent upon temperature reaches MinTemp or MaxTemp centigrade degree Temperature alert function OFF Min Temp Max Temp 31
4. mode 0 e LowTemp and HighTemp means temperature value the range is 10 to 50 centigrade degree if Low7emp equals to HighTemp constant temperature control will be actived e Temperature unit is degree Celsius e Example 1 set commands 159 0 10 20 if the environmental temperature is 5 degrees bellow the limitation of 10 degrees in the command the socket output will be switched on to power heating apparatus and if the environmental temperature is 24 degrees above the limitation of 20 degrees in the command the socket output will be switched off and the heating apparatus stops working e Example 2 set commands 159 1 10 20 if the environmental temperature is 26 degrees above the limitation of 20 degrees in the command the socket output will be switched on to power cooling apparatus and when the environmental temperature is 7 degrees bellow the limitation of 10 degrees in the command the socket output will be off cooling apparatus stops working Successful SMS reply Status ON OFF Temp control function ON OFF Temp Mode Heating Cooling Range Low7emp High Temp 3 6 3 Disable auto controlled by temperature Method The Master user sends following SMS message in order to 26 GSM POWER SOCKET USER MANUAL Disable auto control the output by temperature 159 0 23 Successful SMS reply Status ON OFF Temp control function OFF Temp Mode Heating Cooling Range Low7emp High Temp 3
5. 008 Change the master user s 3 14 NewMaster number Number Add a family number 4 06 FamilyNumber 5 06 FamilyNumber1 Define the 490 several family numbers 4 sramilyNumbordt users R 6 Delete a family number 113 FamilyNumber Delete several family 7 113 FamilyNumber numbers simultaneous 1 _ FamilyNumber4 Delete all family numbers 8 113 ower ane ae ee on off the Disable switching on off the output by calling Default Delay Delay switching on the output 5 61 136 t Minutest 37 GSM POWER SOCKET USER MANUAL Category Function Command P Delay switching off the output after a certain minutes Enable timing switch on the output 17 138 0 Minutes 18 128 1 Timing Set time period to switch on 19 129 WorkDay control the output StartTime EndTime Disable timing switch on the 20 128 0 output Enable auto control the output by temperature 21 15oH1 Set temperature range to 22 159 Mode LowTe Leila switch on off the output mp HighTemp Disable auto control the output by temperature 23 159 0 Enable the over temperature alarm 24 170 1 Over pene 25 170 MinTem temperatur Set limits of temperature e nice MaxTemp Disable the over temperature 26 170 0 2 D 3 Enable the temperature rapid changing alarm Set time period and temperature changing value 27 160 1 Temperatu re rapid changing alarm
6. 7 Temperature alarm 3 7 1 Over temperature alarm Description A range of temperature can be pre set onto the socket In this case if the surroundings temperature is detected out of the pre set temperature range the GSM Power Socket will auto send the SMS alarm message to master s mobile phone This feature depends on the temperature sensor Method The Master user sends following SMS message in order to Enable over temperature alarm 170 1 24 Set limits of temperature 170 in Temo Max Temptt 25 e MinTemp and MaxTemp The values can be set within the range of 10 to 50 centigrade degree Default MinTemp is 20 and MaxTemp is 30 centigrade degree Disable the alarm upon going beyond limits temperature 170 0 26 Successful SMS reply Temperature alert function ON OFF Min Temp Max Temp 27 GSM POWER SOCKET USER MANUAL 3 7 2 Temperature rapid changing alarm Description A time period value and temperature changing value can be pre set onto the socket In this case if the surroundings temperature change to the pre set value within the pre set time period a SMS alarm message will be auto sent to master s mobile phone This feature depends on the temperature sensor Method The Master user sends following SMS message in order to Enable the temperature rapid changing alarm 160 1 27 Set time period and temperature changing value 160 7empt Timet 28 e Temp The values lie
7. SSSUSP ce pk O_ O EAR szIS IS GSM POWER SOCKET USER MANUAL Chapter 3 Advanced settings 3 1 Define the users 3 1 1 User authorization level All the settings of GSM Power Socket can be set or adjusted via a SMS command There are two mobile phone user controlling levels Master user Only one Master user has authorization to use all features of GSM Power Socket In order to enable all the functions on the socket the Master user must store his her mobile number in the socket s memory Only one Master s mobile number Master number is allowed for a socket Family users There are four Family users have authorization to use two commands of switch on or cut off the socket output The other mobile phone users have no authorization to use GSM Power Socket 3 1 2 About the SMS Command Master user s SMS command format code content Family users SMS command format code content password The password must be a four digit number The original password is 1234 The maximum digits that are allows for the phone number is sixteen 16 GSM POWER SOCKET USER MANUAL e GSM Power Socket will reply to the user after it receives the SMS command a Note e The symbol must not be ignored when typing an SMS command No allow any space within the commands 3 1 3 Add a master number to the socket Description If GSM Power Socket is being used for the first time or GSM Power Socket has been rese
8. indicator and Beep warning tone Indicator Action Status No power supply input Power Green light lig Constant Has power supply input light Not installed SIM ard or the power igre switch of socket is OFF GSM Blue light Flash Be busy or searching GSM network Constant light Successfully load to GSM network Constant Output Red light light The socket outlet cuts power supply The socket outlet has power supply GSM POWER SOCKET USER MANUAL R The socket outlet changes power One time supply status Beep Several GSM Power Socket lost external warning tone times power supply Default GSM Power Socket is successfully turning off register GSM network or it is Lon eae successfully reset to its factory settings Note The Beep warning tone can be turn on or turn off by SMS command Refer to Chapter 3 9 for details 11 GSM POWER SOCKET USER MANUAL hapter 2 Quick start H 2 1 Install the SIM card and temperature sensor Tum the power switch to OFF position Loosen the screw and open the socket s SIM cover you will see a SIM card holder Push the metallic cover of the holder to OPEN direction and open j the SIM card holder Put the SIM card on the card holder ensuring that the beveled 1 comer is toward the beveled corner of the SIM holder and the golden contact area is facing downwards Cover back the metallic co
9. it Wipe it with soft wet cloth e Do not attempt to open it except as instructed If the socket does not work normally try to resolve it as the guide of the general troubleshooting if to the problem can not be solved contact with the dealer immediately 33 GSM POWER SOCKET USER MANUAL Chapter 5 General Troubleshooting General Trouble Power indicator light turns off GSM indicator light turns off Socket output cannot be changed by M button All functions disable Indicator is working Socket didn t response of any operation After power on the socket GSM indicator keeps flashing Possible Reason No power input Can t find or identify the SIM card The power switch is OFF No power input The power switch is OFF Caller ID presentation do not active insufficient fee of the SIM card GSM Power Socket work abnormally Network signal weak or network busy 34 Solution Check GSM Power Socket s external AC power is available SIM card no install properly Power off the socket and check it again Power on the socket Check GSM Power Socket s external AC power is available Power on the socket Contact network provider to active SIM card function Pay for the card Switch off the power check SIM card or reset factory setting If mobile phone s signal is weak too place the socket at other place with strong signal and try GSM POWER SOCKET U
10. the socket s SIM number Method The Master user sends following SMS message in order to Add a family number 06 FamilyNumbert 4 Add several family numbers 06 FamilyNumbert FamilyNumber4 5 e FamilyNumber should be the Family user s mobile phone number Succ ssful SMS reply Family numbers set successfully 3 1 6 Check family user s number Refer to Chapter 3 10 Check status 18 GSM POWER SOCKET USER MANUAL 3 1 7 Delete family number 4 Method The Master user sends following SMS message in order to Delete a family number 113 FamilyNumbertt 6 Delete several family numbers simultaneously 113 FamilyNumber FamilyNumber4 7 Delete all family numbers 113 8 Successful SMS reply Family number has been deleted Failed SMS reply The family number does not exist 3 2 Change password Method The Master user sends following SMS message in order to Change the password 04 O dpassworolt Newpasswordt 9 e The password is a four digit number e The original passwordis 1234 Successful SMS reply New password is 3 3 Switching on off the socket output manually Description e When the socket output is switching on GSM Power Socket offers power supply for electronic appliance which being connected with it the red indicator light is lighted constantly Otherwise GSM Power Socket has no power supply for electronic appliance and the red light is tu
11. GSM Power Socket dpo waa Ha a User Manual E GSM POWER SOCKET USER MANUAL GSM Power Socket Thank you for purchasing the GSM Power Socket GSM Power Socket is a remote controlled socket consisting of a GSM module The power supply output of the socket can be tumed on or off remotely by the SMS Short Message System command or local controlled by pressing button It is an intelligent power supply socket controlled by users mobile phone at anytime and anywhere GSM Power Socket is suitable for controlling electrical appliances which power consumption less than 3000W in household or office It is universal for all kinds of indoor power supply sockets With extended connected temperature sensor GSM power socket can switch on or off the socket output according to the environment temperature It s available for power control of the heating or refrigeration plant to keep the environmental temperature within presetting range or at a fixed temperature value Furthermore a SMS notification will be sent to master s mobile phone if GSM Power Socket detects the rapid changing or the reaching of pre set alert value of surroundings temperature GSM Power Socket is mainly applied for house and office usage It is not suited for industry application especially in humidity or dust condition All services and functions need to be supported by the GSM network andra SIM card This br
12. If the Master user calls GSM Power Socket the socket output will 20 oo GSM POWER SOCKET USER MANUAL be switched on or cut off automatically when the user hears the ring tone in the phone The calling will be hung up automatically if the user doesn t hang up the call Method The Master user sends following SMS message in order to Enable switching on off the output by calling 18 1 14 Disable switching on off the output by calling Default 18 0 15 Successful SMS reply Control the socket power output status by calling activated de activated 3 4 Delayed switch on off the socket output Description l e The output of GSM Power Socket can be set to delay switch on or off for a period with SMS commands e When the delayed switch on off the socket function is applied the preset timed switch on the output function will be invalid at once e When the delayed switch on the socket command is received and if the socket output is switched on the socket output will be switched off immediately and be switch on again as the setting delayed time is reaching Contrarily if the socket output is switched off the output will remain switching off until the setting delayed time is reaching Afther switching on the output the following SMS reply will be sent Status ON Delay control function OFF e When the delayed switch off the socket command is received and if the the socket output is swi
13. SER MANUAL General Trouble The master number already exists Invalid format Please check and try again No authorization user Possible Reason SIM card PIN code actives SIM card invalid Other master is already set in the socket Invalid command 35 Solution Close the PIN code Contact with local operator to check of it Change Master number or recover to factory default setting Refer to the user manual Use the Master mobile phone to try the command again Note If the problem can t be solved with above guidelines contact to your local distributor or after service center GSM POWER SOCKET USER MANUAL Chapter 6 Main Technical Parameters 190 2S0V 50HZ Input power socket CEE 7 7 hybrid Schuko French plug 100 240V 50HZ 2 0V 30A 30s Output power socket 16A long duration CEE7 4 German Schuko Operating temperature 10 C 50 C Store temperature 20 C 60 C Relative humidity 10 90 without condensation Communication GSM PHASE 2 2 E protocols including data operation Data interface GSM SIM 1 8V 3 0V socket External temperature 10 C 50 C sensor GSM850 EGSM900 GSM working band DCS1800 PCS1900 Optional SLT 36 GSM POWER SOCKET USER MANUAL Appendix SMS commands list Category Function Command 1 Time Regulate the socket time 152 SIMCardNumber Add a master number to the 2
14. day Saturday Monday to Friday e StartTime and EndTime Be consists of 4 digits hh mm and works on a 24 hour clock The StartTime and EndTime should be in the same day and the EndTime must be later than StartTime e The socket output will switch on at the StartTime and cut off at the EndTime e For example 129 1 0000 2130 0000 means time 00 00 hh mm AM 2130 means time 9 30PM Successful SMS reply Schedule control function ON OFF WorkDay StartTime EndTime 3 5 3 Disable timing switching on the output Method The Master user sends following SMS message in order to Disable timing switch on the output 128 0 20 Successful SMS reply Schedule control function OFF WorkDay StartTime EndTime 3 6 Auto control the socket output by temperature 3 6 1 Enable auto controlled by temperature 2 Description e The external temperature sensor must be inserted into the I O port of GSM Power Socket The output status of the socket can be controlled by the environmental temperature automatically e If users don t open the timed switch on the socket or delayed 24 GSM POWER SOCKET USER MANUAL switch on off the socket functions the socket will control to switch on or cut off the output according to temperature setting e f users open the timed switch on the socket or delayed switch on off the socket functions the temperature control function will only be valid when power output
15. e the original password at the beginning use Be sure to keep the password and SIM card number secret Do not disclose this information to anyone other than the authorized users in order to ensure your safety For your safety This socket was designed for home or office use Do not use it on the electrical appliance which is for industry or business operation for example iatrical appliances large heaters and refrigerates Before using this socket make sure that the mobile phones can be used well in the area otherwise do not put this socket into operation The power consumption of the appliances connected with the socket cannot exceed 3000W and the current cannot exceed 16A The electrical appliance which power consumption is higher than 1500W must be grounded Do not make two plugs of socket short circuit Do not touch the socket jack by any metal objects or hand This socket was designed for indoor use Don t use it in wet chemically aggressive or dusty environment 5 GSM POWER SOCKET USER MANUAL Do not open the case unless maintenance needed Do not keep shaking or fall down this socket otherwise it can be damaged a This socket is a wireless signal transmission socket Keep it away from electronic equipment likely to interfere with the wireless signals in order to avoid signals interference Switch off this socket and mobile phone when entering areas marked Explosive Might explode Closed wireless tran
16. ect the socket feature Therefore before using the user should ensure that GSM Power Socket is used in an area with a strong GSM network signal e For the first time use the user should perform a test run by sending SMS to the socket This allows the user to check the GSM network connection of the socket 2 3 Add a Master number to the socket The user must edit and send the following SMS to socket via his her mobile phone the phone number will be the Master number in order to Add a Master number to the socket 00 Successful SMS reply Welcome to use GSM Power Socket Your Password is 1234 13 GSM POWER SOCKET USER MANUAL 2 4 The regulation of time Important note If GSM Power Socket is being used for the first time or it has been reset the Master user must adjust the socket time according to the current time of SMS center Otherwise GSM Power Socket will use the original time from 00 00 00 1 amp t Jan 2004 EX Method The Master user sends following SMS message in order to Regulate the socket time 152 S MCardNumbert 1 e The SIMCardNumber should be the SIM card number of GSM Power Socket Successful SMS reply The socket current time is yyyy mm dd hh mm 2 5 Socket output switching on off Method Method 1 To press M button 0 5 second See 3 on Figure Method 2 The Master user sends following SMS message to socket in order to Switch on the socket output 01 Switch off the soc
17. in the range of 1 to 50 centigrade degree Time The values lie in the range of 1 to 300 minutes Default Temp is 2 degree and Time is 1 minute Disable the temperature rapid changing alarm 160 0 29 Successful SMS reply Fast temperature changing function ON OFF Delta Time minutes 3 8 SMS notification upon the socket output changing Description GSM Power Socket will default notify the user when the state of the socket output is changed with a SMS notification The Master user can enable disable this SMS notification Method The Master user sends following SMS message in order to SMS notification upon the socket output changing Default 11 1 30 No SMS notification upon the socket output changing 11 0 31 28 GSM POWER SOCKET USER MANUAL Successful SMS reply Set no SMS notification when socket output changed Set SMS notification once socket output changed 3 9 SMS notification upon external power supply changing Description GSM Power Socket will default notify the user when the state of the external power supply is changed with a SMS notification For example Main electricity supply lost Temp or Main electricity supply restore Status ON Temp The Master user can enable disable this SMS notification Method The Master user sends following SMS message in order to set SMS notification upon the power supply changing Default 12 1 32 No SMS notification upon the power s
18. is switch on including timed switch on or delayed switch on time period e For example GSM Power Socket is used for the power control of the heating apparatus If users set the socket output on when indoor temperature is bellow 20 degrees and off when indoor temperature is above 28 degrees Meanwhile users set the GSM Power Socket output is on from 9am to 5pm In this case the socket will control to switch on or off the output according to indoor temperature automatically from 9am to 5pm duration Method The Master user sends following SMS message in order to Enable auto control the output by temperature 159 1 21 Successful SMS reply Status ON OFF Temp control function ON Temp Mode Heating Cooling Range LowTemp HighTemp Then GSM Power Socket can switch on or off the output automatically according to the temperature range setting 3 6 2 Set temperature range to switch on off the output Description After successful setting of temperature range the temperature parameter will be saved on the socket until GSM Power Socket is reset to factory settings But the Auto controlled by temperature feature is applied only 25 GSM POWER SOCKET USER MANUAL when command 20 be set Method The Master user sends following SMS message in order to Set temperature range to switch on off the output 159 Modet LowTempi HighTemp 22 e Mod eis the control selection For coldness mode 1 For warmness
19. ket output 02 Successful SMS reply Status ON OFF Temp Temp control function ON OFF Schedule control function ON OFF Delay control function OFF GSM POWER SOCKET USER MANUAL 2 6 External power supply notification GSM Power Socket will notify the user when the external power changes The Beep Beep tones will be heart if enabled also a SMS notification will be sent if the SIM card is available Lost external power supply If the plug of GSM Power Socket is disconnected from external AC power or lost of the AC power occurs all operating on GSM Power Socket is de activated including M button and all SMS commands GSM Power Socket will notify the user Main electricity supply lost Temp Resume external power supply If the AC power of GSM Power Socket is available again the SMS notification will be sent to the user i e Main electricity supply restore Status ON OFF _Temp When the external power supply is resumed the output of GSM Power Socket will keep its previous working status For example if the output is switched on before the external power supply cut off the output will be switched on when the external power supply is resumed If the power supply is switched on and off frequently GSM Power Socket will send reminding SMS messages The SMS notification upon external power supply changing can be disabled Refer to Chapter 3 8 ee Se SS E M M o l aE M l 0 EE
20. n the socket Output eee cee eeeeeeteteee 22 3 GSM POWER SOCKET USER MANUAL 3 6 Auto control the socket output by temperature 2h 3 7 Temperature alarm sscccssecsssesssssesssueeesueseeeneeseneesenmeecsseeseeee 27 3 8 SMS notification upon the socket output changing 28 3 9 SMS notification upon external power supply changing 29 3 10 Beep warning tone c cscescssescsesecsesesssecscsesserseecseracsesseacsees 29 3 11 Check Status sccsccsesessssscsssessssessscsssessssesecssaesssesersesererssaesees 30 3 12 Resetting the SOCKet ccccccescsescsescsesesessavscacssecenseseueceescees 32 Chapter 4 Maintenance ccccccccsssesssesesesesecesessssssccseresestavsceeseseses 33 Chapter 5 General Troubleshooting c c cccccccssessssesecsescscscsescscecseees 34 Chapter 6 Main Technical Parameters c cccssssscssesesessesecsesesecseee 36 Appendix SMS commands list scscssssssssssesssssesecscecscssacscecseecseees 37 GSM POWER SOCKET USER MANUAL 1 Purchase a GSM SIM card mobile phone card from GSM network service provider and install it in the socket This SIM card number is referred as GSM Power Socket number on this brochure 2 The user needs to activate the Caller ID Presentation function of SIM card and deactivate PIN code of the SIM Contact with GSM network service provider for support 3 Chang
21. ochure suits for GSM Power Socket model Details of the functioning and advanced operation of this socket are described in this instruction manual gt GSM POWER SOCKET USER MANUAL CONTENT For your safe Pinnen 5 Exception QaUSErssicrn naona 6 Chapter 1 Features and aACCessorjes ccecseccceeesesseteeseeeeaeeseesesentes 7 1 1 Main function 1 2 Package Comensais raa AERAN 8 1 3 Sockets iNStrUCtiONS cece eeeesceecseeseneseeeeaseeseeeseeeseneenees 9 1 4 Light indicator and Beep warning tone 10 Chapter QUICK SIAM seccecceeasuescssscnscessnsoievedsesctsscvisssseusdaiientsisredencnaeenanas 12 2 1 Install the SIM card and temperature Sensor 12 2 2 GSM Power On Off siiscisevscesscsiasanssisarssssressesscrecesevavsvoneresevsesiesaves 12 2 3 Add a Master number to the socket 2 4 The regulation Of tiMe cccececsesseseesetseseeesessesecnecnensnerattees 14 2 5 Socket output switching ON Off eee cece eects eneeeeeeeeeeee 14 2 6 External power supply notification 0 00 cc ccccseececeeseeteeeeeeees 15 Chapter 3 Advanced settings c cccecssseeseessseeseneeseseetectensenteeetenaeees 16 3 1 Define the users 3 2 Change passwold veccccicccccrcamssivssvissasasscssenaccesveacneenerereacenncecesnee 19 3 3 Switching on off the socket output manually cccceeeeees 19 3 4 Delayed switch on off the socket OUtpUt eect teers 21 3 5 Timed switching o
22. rned off e Note If the socket output status is changed manually including pressing the M button sending SMS making phone call the preset timing delaying or temperature control of the socket will be invalid 19 GSM POWER SOCKET USER MANUAL automatically and a SMS notification message will be sent to the Master but the setting time range and temperature range parameters will be saved until GSM Power Socket is reset to factory settings 3 3 1 Switching on off by SMS Method The Master user sends following SMS message in order to Switch on the socket output manually 01 10 Cut off the socket output manually 02 11 The Family users send following SMS message in order to Switch on the socket output manually 01 Password 12 Cut off the socket output manually 02 Password 13 e Password should be 4 digits password number Default 1234 e SMS reply will be also sent to Master user when Family users use these two commands to change the socket output successfully Successful SMS reply Status ON OFF Temp Temp control function ON OFF Schedule control function ON OFF Delay control function ON OFF 3 3 2 Switching on off by M button Keep press M button on the GSM Power Socket for half a second The OUTPUT indecator light will turn on or off to indicate that G M Power Socket output is switching on or off _ he SMS reply is same with Chapter 3 2 1 3 3 3 Switching on off by calling Description
23. sceiver sockets etc Do not cast this socket in a fire as this may cause explosion a This socket should only be operated from power approved by the socket manufacturer The use of any other types of power may damage the socket Keep the socket and its accessories out of the children reach Exception clause 1 We operate on a policy of continuous development We reserve the right to make changes and improvements to any of the sockets described in this document without prior notice 2 We don t guarantee for the document veracity reliability or any content except regulate in proper laws Including no guarantee for socket suitable market or suitable area promise 3 We hold no responsibility for the illegal use of this socket 4 We hold no responsibility for any loss of income or any special incidental consequential or indirect damages howsoever caused 5 The contents of this document are provided as is Except as required by applicable law no warranties of any kind either expressed or implied including but not limited to the accuracy reliability or contents of this document We reserve the right to revise this document or withdraw it at any time without prior notice GSM POWER SOCKET USER MANUAL Chapter 1 Features and accessories 1 1 Main function This socket uses a GSM SIM card Remotely operate by SMS command The socket be controlled and set by sending SMS commands Input 100V 250V 50Hz Outpu
24. t Max 16A for long duration operation Relay 30A 250V relay with two working status power on off for output outlet M button To manual control output power on off Delayed control socket output Auto operates by preset schedule Fixing time control output power on off External temperature sensor supported Send environmental temperature SMS to mobile phone Auto operates by temperature Available for power control of the heating or refrigeration plant to keep the environmental temperature within presetting range or at fixed temperature value SMS alarm when temperature rapid changing or reaching the pre set value When it detects the rapid changing or the reach of pre set alert value of surroundings temperature it can auto send the SMS alarm message to master s mobile phone Support 5 mobile phone users Auto time synchronization SMS notification upon external power source changing GSM POWER SOCKET USER MANUAL GSM POWER SOCKET USER MANUAL 1 3 Sockets instructions Data port Temperature sensor port Socket Indicator light Power GSM Output Temperature sensor 1 unit Socket plugs GSM Power Socket Power switch SIM card holder User manual 1 unit Figure 1 GSM Power Socket instructions 8 9 GSM POWER SOCKET USER MANUAL Temperature sensor Standard 3 5mm interface put into 2 of Figure1 Figure 2 Temperature sensor Instruction 1 4 Light
25. t to factory settings the Master user s number must be programmed into the socket Method The user must edit and send the following SMS to socket via his her mobile phone the phone number will be the Master number in order to Add a master number to the socket 00 2 Successful SMS reply Welcome to use GSM Power Socket Your Password is 1234 Failed SMS reply If a user tries to add another Master user again GSM Power Socket will send a notification via SMS stating The master user already exists The Master number should be changed Refer to Chapter 3 1 4 3 1 4 Change the master number Method Method 1 The Master user sends following SMS message in order to Change the master user s number 14 NewMasterNumber 3 17 GSM POWER SOCKET USER MANUAL e NewMasterNumber should be the new Master user s mobile phone number Method 2 GSM Power Socket should be reset to factory settings to remove old Master number before setting the new one Refer to Chapter 3 11 Successful SMS reply New master number set successfully Successful SMS reply will be sent to the new Master user Then the old Master user s number will not be able to control GSM Power Socket anymore 3 1 5 Add a family number Up to 4 family users number can be stored on one socket Family users have the authority to send SMS command to switch on or cut off the GSM Power Socket output The family users should remember and safeguard
26. tched on the socket output will remain the switch on state and be switched off as the setting delayed time is reaching If the socket output is switched off it will be switched on 21 GSM POWER SOCKET USER MANUAL immediately and be switch off again when reaching the setting delayed time After switching off the socket output the following SMS reply will be sent Status OFF Delay control function OFF Method The Master user sends following SMS message in order to Delay switching on the output after a certain minutes 138414 Minutes 16 Delay switching off the output after a certain minutes 138 0 Minutes l 17 Minutes are time parameters its range is 0 720 e When Minutes is 0 the delayed switch on off the socket function will be invalid but the current output status won t be changed Successful SMS reply Status ON OFF Output will switch off on after minutes 3 5 Timed switching on the socket output 3 5 1 Enable timing switching on the output Description e The output of GSM Power Socket can be set to switch on for a duration and then be switch off after the duration e If the socket output status is changed manually including pressing M button sending SMS and making phone call the preset timing delaying or temperature control of the socket will be invalid automatically but the setting time range parameters will be saved until GSM Power Socket is reset to factory settings If these f
27. unctions need to be restarted the following SMS commands must be set Timing 128 1 Temperature control 159 1 delayed switch on off the socket commands need to be reset 22 GSM POWER SOCKET USER MANUAL Method The Master user sends following SMS message in order to Enable timing switch on the output 128 1 18 Successful SMS reply Schedule control function ON WorkDay StartTime EndTime If the value of the WorkDay StartTime EndTime on the SMS reply are all 0 it means the time duration has not been set Refer to 3 4 2 Then GSM Power Socket will keep switching on or off the output automatically according to the schedule settings 3 5 2 Set time period to switch on the output Description After successful setting of time duration to switch on the socket output the schedule parameter will be saved on the socket until GSM Power Socket is reset to factory settings But the timed switch on the output feature is applied only when command 17 be set Method The Master user sends following SMS message in order to Set time period to switch on the output 1294 WorkDayt StartTimet End Timey 19 e WorkDay one digit the values lie in the range of 0 to 8 The following table contains the descriptions of each value Value Corresponding day 0 Sunday 1 Monday 2 Tuesday 3 Wednesday 4 Thursday 23 GSM POWER SOCKET USER MANUAL Fri
28. upply changing 12 0 33 Successful SMS reply No SMS notification upon main electricity supply changing 3 10 Beep warning tone Description A Beep warning tone will be sounded if the work state of GSM Power Socket is changed The Beep warning tone is default turning off The Master user can enable it by sending SMS command N Method 29 GSM POWER SOCKET USER MANUAL The Master user sends following SMS message in order to Enable the Beep warning tone 19 1 34 Disaable the Beep warning tone Default 19 0 35 Successful SMS reply Beep alarm activated de activated 3 11 Check status Method The Master user sends following SMS message in order to Check socket operating status 07 36 After receiving the SMS commands GSM Power Socket will reply one SMS message of socket status checking Number kkkkkkkkkk Status ON OFF TEMP Temp control function ON OFF Schedule control function ON OFF Delay control function ON OFF Check socket output status 000 37 After receiving the SMS commands GSM Power Socket will reply one SMS message of socket output status Status ON Temp 23 Check delayed switch on off the socket parameters 138 38 After receiving the SMS commands GSM Power Socket will reply one SMS message of Delayed switch on off the socket parameters checking Status ON OFF Output will switch off on after minutes
29. ver and push it to LOCK direction The SIM card will be fixed in the holder Screw the SIM cover back Insert the temperature sensor into the W O port until it is seized 2 2 GSM Power onl off Power on 1 Turn the power switch to On position See 7 on Figure1 2 Plug the GSM Power Socket in an AC power socket See 6 on Figure The blue light will be flashing slowly for about 20 seconds then blue light be on constantly and a long Beep tone can be heard if Beep ___ Warning tone is enabled The default state of the socket outlet is no power supply output 3 Insert the plug of electronic appliance in the GSM Power Socket electrical outlet See 4 on Figure 12 GSM POWER SOCKET USER MANUAL 4 M button See 3 on Figure1 can be pressed for about 0 5 second to switch on or off the output of socket After adding user numbers to the socket users can send SMS command to control the power supply output Refer to Chapter 3 2 Power off 1 Turn the power switch to Off Position The blue light turns off 2 The socket outlet can work as a normal power socket GSM Power Socket can not be controlled by SMS commands M button is disabled ran Note 1 If the GSM indicator light is not constant lights which imply the SIM card working abnormally all functions of this socket are invalid 2 Check GSM network signal of the using place e The GSM network s signal strength may aff
Download Pdf Manuals
Related Search