Barrel LPT - Apeom s.r.o.
Contents
1. apeom Barrel LPT User Manual Safety Precautions Read this User Manual carefully before first use of the equipment Use the equipment only as described in this manual Do not use the equipment for other purposes than for which it is intended Do not aim at people or animals or to an uncontrolled area The emitter is an optoelectronic device its disassembly is forbidden Observe general rules for weapon handling while operating the weapon Use the equipment only in dedicated areas bounded for shooting Observe general rules for behaviour and handling a weapon on a shooting range After finishing shooting check if the weapon was not left cocked Do not look into the emitting opening of the emitter Purpose Barrel LPT is designed for performing sport and training shooting at electronic targets Barrel LPT is designed for imitation of a bullet by emitting an optical ray during the shot Barrel LPT is designed for mounting to a body frame of an air gun Description I emitter 2 adapter 3 emitting aperture opening 4 mode button 5 adjusting screw 6 lid 7 lid screw 8 openings for bolting of a foresight 9 spacer screw 10 fixing screw Preparation for Operation Unscrew the lid screw 7 and remove the lid 6 Loosen up the spacer screw 9 by half turn and loosen up the fixing screw 10 so that the emitter can be moved on the adapter 2 by 10 mm back and forth Move the2. 11 Web Czech Republic www apeom cz Page 3 apeom CAUTION Using different checks settings or operating procedures than the ones mentioned above may lead to dangerous radiation exposure Environment Protection Do not throw the batteries to a waste bin Take the batteries to collection points Specifications Name of parameter laser type laser class wavelength A Diameter laser dot lens output aperture diameter according to the manufacturer output P Mode with UIPM code emission duration T carrier frequency pulse ration numbers and lengths of pulses operating temperature weight emitter MORINI 162 adapter batteries emitter power supply Special Provisions Value semi conductor CLASS 2 LASER PRODUKT 650 nm 5 lt 6 mm 10 m 3mm lt 3 4 mW 15 6 ms 40 kHz 1 1 1 2 4 6 1 2 2 0 6 ms 10 C to 30 C 0 2 kg 4 5 VDC 3xLR54 or equiv The emitter is equipped with a warning information plate serial number plate and sealing stickers Plate Warranty for the equipment is void in case of damage to the plate or sealing stickers The warning information plate is located on the bottom side of the emitter body APEOM s r o Address i Telephone M rov 24 tel 420 596 614 795 CRN Identification Number 25876911 APEOM Changes reserved E mail e info apeom cz 703 00 Ostrava 3 VAT Czech Republic IDe C258 T76911 Web w
3. emitter forward and insert batteries to the battery compartment Use 3 pieces of LR54 alkaline batteries or equivalent Observe battery polarity that is marked on the lid Push the emitter back on the adapter and tighten APEOM s r o Address Telephone Identification Number E mail APEOM Mirova 24 tel 420 596 614 795 CRN 25876911 info apeom cz Changes reserved 703 00 Ostrava 3 VAT ID CZ29876911 Web Czech Republic www apeom cz Page 1 apeom the fixing screw then the spacer screw Mount the lid and screw up the lid screw Do not use excessive force to retighten the lid screw Mount the foresight on the emitter and screw it into one of the opening for bolting of a foresight 8 Use one M3x5 countersunk screw to screwing up the foresight Do not use a longer screw the emitter might be damaged Mount the adapter 2 to the weapon frame screw up the screws on the weapon frame so that the adapter can be turned without being pushed out By looking through the back sight turn the adapter so that the foresight was aligned with the back sight Tighten the screws of the weapon frame Fill the air container with air and screw it into the weapon Barrel LPT is ready for operation Rules of Operation Never aim at persons animals or to an uncontrolled area it is necessary to observe general rules for weapon handling and general rules for behaviour on a shooting range while using the equipment The emitter wor
4. he lid then loosen up the spacer screw 9 by half turn then loosen up the fixing screw 10 so that the emitter can be moved on the adapter Shake out the old batteries insert the new batteries while observing battery polarity Push the emitter back by about 10 mm back on the adapter tighten the fixing screw tighten the spacer screw Replace the lid Never remove the batteries using a different method than the above especially by forcing the batteries out with a metal object Batteries Do not charge the batteries This would pose a risk of leaking electrolyte or explosion Use the batteries only in intended electronic devices In case of using an unsuitable battery the equipment may be damaged or destroyed Keep the batteries out of humid environment this would pose a risk of leaking electrolyte due to corrosion of the case The electrolyte is a strong caustic that causes alkali burn in contact with skin Do not use damaged batteries Be careful when handling the button cells due to their small dimensions Keep the batteries out of children Observe correct polarity of the batteries do not short circuit Do not throw batteries into fire do not solder do not disassemble Do not mix batteries of different type or age the batteries discharge faster Store the batteries in a dry place under temperatures between 5 30 C Take the batteries to a collection centre for hazardous waste or collection points Maintenance Keep
5. ks in two modes One is the shooting mode where the laser emitter is used for shooting at a target The other is adjusting mode in which sighting can be done Modes can be chosen using mode button 4 Changing modes Cock the weapon push the mode button 4 pull the trigger and release the mode button The emitter switches to adjusting mode for about one minute and starts emitting short pulses Do not look into the emitting opening Place the Barrel LPT to a white underlay and check the emitted information If the emitter sends an information in the form short pulse pause about second short pulse pause etc isc ise rectification mode 10x short puse 0 O O flat battery indication Adjusting mode ends automatically after about 1 minute or it can be turned off by holding the mode button for gt 3sec By turning off the adjusting mode with the button you save batteries In case that Barrel LPT will not be used for a long time more than 1 month remove batteries Always insert new batteries to the emitter Only use alkaline batteries of the following types L1131 LR54 AG1O V10GA GP189 APEOM s r o Address Telephone Identification Number E mail APEOM Mirova 24 tel 420 596 614 795 CRN 25876911 info apeom cz Changes reserved 703 00 Ostrava 3 VAT ID CZ29876911 Web Czech Republic www apeom cz Page 2 apeom When replacing batteries first remove t
6. the emitter clean by wiping dust with a dry cloth Do not use any cleaning agents solvents and chemicals Do not push against the emitting opening optics with any objects Store the emitter so that clogging of the emitting opening is prevented Treat the adapter by wiping with a cloth gently moistened with oil Use water repellent oil such as WD40 After every shooting and before every shooting visually check intactness of the emitter and adapter check batteries for corrosion Remove the batteries if there are marks of corrosion on them Let the emitter the dry up before storing the emitter to a weapon case Also let the emitter to dry up in case that you used it in humid or rainy conditions In case that Barrel LPT will not be used for a long time more than 1 month remove batteries Potential Defects and Troubleshooting The emitter does not send the laser ray while Check whether the batteries are inserted or shooting check whether there is enough air in the container or replace the batteries or check if the emitting opening is not clogged or tighten the screws of the weapon frame that hold the adapter or tighten the fixing screw and the spacer screw The emitter cannot be switched to the Replace the batteries adjusting mode APEOM s r o Address Telephone Identification Number E mail APEOM Mirova 24 tel 420 596 614 795 CRN 25876911 info apeom cz Changes reserved 703 00 Ostrava 3 VAT ID CZ258769
7. ww apeom cz Page 4
Download Pdf Manuals
Related Search