Product datasheet
Contents
1. AC Source Analyzer E Single Box AC Power System Combined AC power source and power analyzer m 3000VA 4500VA or 4800VA Power Levels Match power source and cost to application requirements mE Arbitrary Waveform Generator Test products for harmonics susceptibility E Built in Power Analyzer Performs voltage and load current harmonic analysis E Selectable Output Mode Drives single and three phase loads i m High Crest Factor Capability Drives a wide variety of non linear loads E CE Marked Safe reliable and consistent operation Integrated System The iL Series represents a new type of AC power source that addresses increasing demands on test equipment to perform more functions at a lower cost By combining a flexible AC power source with a high end harmonic power analyzer the iL Series systems are capable of handling applications that would traditionally have required multiple instruments The sleek integrated approach of the iL Series avoids the cable clutter that is commonly found in AC test setups All connections are made internally and the need for external digital multimeters power harmonics analyzer and current shunts is completely eliminated Using a state of the art Digital Signal Processor in conjunction with precision 16 bit A D converters the iL Series provides more accuracy and resolution than can be found in most dedicated harmonic power analyzers Since many components in the iL Ser2. Synchronization Ft ppm Current shunt burden Oos Current harmonic smoothing filter J SS Pst Integration time 8 5 10 0 15 min Pp Samplerate Window width Acq overlap 50 Hz Operation Rectangular measurement window Frequency 0 01 0 01 Hz of setting Phase 0 1 45 100 Hz a 100 Hz 1 kHz 1 1 kHz gt 1 kHz Frequency Range 3000iL 45 Hz 5000 Hz 4500iL 45 Hz 5000 Hz 4801iL 45 Hz 1000 Hz Steady State Current Capability 3000iL 4500iL phase range T 12 8 kHz 8 533 kHz 16 cycles 24 cycles three single a o oA Model 480tiL phase range single __high 16A low 32A Peak cepete AC Current phase rane V three single low oa 720A Moder omi phase rane V hig A ow a Current Limit Programmable from 0 A to max current for selected range Hanning measurement window 60 Hz Operation Rectangular measurement window Hanning measurement window 15 360 kHz 7 680 kHz 16 cycles 32 cycles Specifications are in of reading for 4801iL sinewave output with resistive load at output freauencv of 50 or 60 Hz in IEC mode of operation Output Noise 60 dB from 20 kHz to 1 MHz Harmonic Distortion Less than 1 below 1 kHz Less than 1 1 kHz from 1 kHz 5 kHz Isolation Voltage 300 V rms output to chassis Output Relay Push button controlled and bus controlled output relay Output impedance Fixed on 3000iL
3. Line Frequency Protection Supplied with 47 63 Hz ver Load e User manual e Constant Current or Constant SOFI i a manual o typical Voltage mode e Windows Graphical User Interface Power Factor Over Temperature software 0 6 typical Anomalie endows e RS232C Serial cable Hold up Time e HFTS Software 4801iL only At least 10 ms System Setup storage 16 complete instrument setups User waveform storage 12 user defined arbitrary waveforms of 1024 points each Transient lists storage up to 100 transient steps per list Output change response time 50 usec for 10 to 90 of full scale change into resistive load Trigger input Triggers measurements or transient steps BNC 10K pull up Response time 400 usec Trigger output BNC HC TTL output Regulatory IEC1010 CSA22 2 No 231 EN50081 2 EN50082 2 CE EMC and Safety Mark requirements RFI Suppression CISPR 11 Group1 Class A Physical Dimensions Height 10 8 276 mm Width 16 96 431 mm Depth 23 7 602 mm 1 Height includes feet Subtract 0 5 13 mm for rack mount Depth includes rear panel connectors Weight 193 lbs 87 7 Kg net 280 lbs 127 3 Kg shipping Vibration and Shock Designed to meet NSTA project 1A transportation levels Air Intake Exhaust Forced air cooling side air intake rear exhaust Operating Temperature 0 to 40 C Storage Temperature 40 to 85 C Options RMK Rack mount kit RMS Rack mount slides Customer Support For tech
4. Real time test data display A complete software package e Archiving of test data to mass storage devices Harmonics and Flicker Test e Pass Fail indication System software HFTS is e On line or off line data analysis and reporting AeA Aaa ZOGRIL iG e Data analysis to assist in EUT modification to achieve pass status accommodate data collection analysis and reporting This Requirements translates into a single box PC 486DX4 Pentium 100 MHz or better IEC test solution that does not Su anr J recommended require additional Operating ices ule wien si Bieta System Windows 3 1 Windows 95 ISOM IME glalonon SORNATG Memory 8 MB minimum 16 MB recommended development on the part of a the user Just connect your Hard disk rated requires 4 MB of disk EEE 488 compatible PC and Soi j that s it Since the 4801iL Networking Not supported houses both the AC source Interfaces National Instruments AT GPIB TNT or HP82335B and the digital power analyzer flicker meter operating on the same internal timebase the possibility of timing errors between source and analyzer i HFTS Screen is reduced producing reliable showing real time test data fluctuating When not used for IEC E r AA Harmonics teat IEC A n l lew pions Mir type testing the 4807iL i g pa DHR doubles as a standard single phase 4800 VA AC power source analyzer combination The California Instruments Graphical U
5. age rms FreqqHz 60 0 Phic E Phase E Phooe e Current rms F Voltage V smal e Peak Current S Curent A ons e Crest Factor Miamia e Neutral Current rms a ae e Real Power oa eh ae e Apparent Power Peak Cor Al eh e Power Factor E Chest Factor Analysis Functions In addition to standard load parameters the iL Series is capable of measuring voltage and current amplitude and phase harmonics up to the 50th harmonic for fundamental frequencies up to 250 Hz Total harmonic distortion of both voltage and current is also available Measurement analysis data can be viewed from the front panel or transferred to a PC through the IEEE 488 or RS232C bus Remote Control Standard IEEE 488 and RS232C remote control interfaces allow programming of all instrument functions from an external computer The popular SCPI command protocol is used for programming Windows Graphical User Interface A Windows 3 1 compatible Graphical User Interface GUI offers a soft front panel interface for operation from a PC Harmonic and Arbitrary waveforms can be created and downloaded to the iL Series Up to 12 user defined arbitrary waveforms can be saved in non volatile memory The same program provides visual full color displays of harmonic measurement results obtained from the integrated power analyzer Data can be printed or saved to disk for export to other analysis programs and later recall Low Cost Of Ownership Through the use of
6. and 4500iL Programmable on 4801iL Note 1 Specifications are warranted over an ambient temperature range of 25 5 C Unless otherwise noted specifications are per phase for a sinewave with a resistive load and apply after a 30 minute warm up period Input Voltage Standard 180 254 VAC L L 3 Phase Option 400 360 440VAC L L 3 Phase Input range must be specified when ordering Line Current per phase Model 3000iL 4500iL 4801iL 180 254 V 360 440 V Remote Control IEEE 488 2 Interface IEEE 488 GPIB talker listener Subset AH1 CO DC1 DT1 E1 LE4 PPO RL1 SH1 SR1 TE6 RS232C Interface Bi directional serial interface 9 pin D shell connector Handshake CTS RTS Databits 7 with parity 8 without parity Stopbits 2 Baud rate 300 600 1200 2400 4800 9600 Rear Panel Connectors e Three phase AC Input terminal block with cover e Three phase AC output terminal block with cover e IEEE 488 GPIB connector e 9 pin D Shell RS232C connector Remote Inhibit Discrete fault indicator RI DFI port Remote voltage sense terminal block Trigger in and Trigger out BNC RS232 DB9 to DBY cable supplied Ordering Information Supplied with RS232C cable Model Inrush Current Code and Format 3000iL 208 V 30 L L 4801iL Response times 4500iL 208 V 3 L L Remote command response time 4500iL 400 400 V 30 L L typically 10 msec 4801iL 208 V 30 L L 4801iL 400 400 V 3 L L
7. e with the iL Series This software allows easy use of the iL series many powerful capabilities The following functions are available through this GUI program Steady state output control all parameters Create run save and print transient programs Generate and save harmonic waveforms Generate and save arbitrary waveforms Download data from a digital storage oscilloscope Measure and log standard measurements Capture and display Voltage and Current waveforms Measure display print and log harmonic voltage and current measurements e Calibrate measurement functions 1 Requires PC running Windows 3 1 Recommended 486DX 33 MHz or better California Instruments Total Customer Satisfaction is the goal of all California Instruments employees It is the driving force behind everything we do This not only affects the product that you purchase from California Instruments but everything about your interface with the company Our applications engineers are ready to assist you with your AC power application With over 35 years of experience designing and building precision AC power supplies chances are we can meet your needs and exceed your expectations The same dedication to customer satisfaction you will find in our applications group also permeates our modern manufacturing facility where our products are carefully built No unit leaves our factory without being thoroughly tested to ensure quality reliab
8. ective easy to implement single box solution for many such applications including the new Euronorm IEC 1000 standards Versatility High Crest Factor With a crest factor of up to 4 1 for the 4500iL and no less than 6 1 for the 3000iL the iL Series AC source analyzers can drive difficult non linear loads with ease Since many modern products use switching power supplies they have a tendency to pull high repetitive peak currents If the AC power source used to test these products has insufficient peak current drive capability the waveform exhibits voltage harmonic distortion The iL Series can deliver up to 120 Amps of repetitive peak current in single phase mode or 40 Amps per phase in three phase mode low range Multi phase Configurations Models 3000iL and 4500iL offer both single or three phase mode switching from either the front panel or the IEEE 488 and RS232C bus This often avoids the need to purchase more than one AC source for testing both single and three phase products In single phase mode output amplifiers are paralleled to provide three times the maximum current on a single phase Advanced Measurements The iL Series incorporates a sophisticated digital multi phase power analyzer capable of measuring a wide range of load parameters Standard Measurements The following standard measurements are available from the front panel or via the bus e Frequency e Phase AC Soare Mensurcmime Meaiemenis ig Volt
9. ies are shared between the AC source and the power analyzer the total cost of the AC Power Systems iL Series AC Power Source and Analyzer Combination is ok senor a le i T i SSS integrated system is less than the typical cost of a multiple unit system Easy To Use Controls The iL Series is completely microprocessor controlled and can be operated from an easy to use front panel keypad Functions are grouped logically and are directly accessible from the keypad This eliminates the need to search through various levels of menus and or softkeys A pair of analog controls located directly below the bright fluorescent alphanumeric display allows output voltage and frequency to be slewed up or down dynamically Both controls employ a dynamic rate change algorithm that combines the benefits of precise control over small parameter changes with quick sweeps through the entire range W California Instruments Applications With precise output regulation and accuracy high load drive current multi or single phase mode and built in power analyzer measurement capabilities 3000iL and 4500iL AC source analyzers address all application areas for AC power testing Additional features like line distortion simulation LDS and arbitrary waveform generation address requirements for product quality and regulatory compliance testing IEC Test System Model 4801iL is supplied with a special Windows 3 1 o
10. ility and conformance to specifications CE Mark The iL Series power sources have been fully tested for compliance with 1996 CE Mark requirements This allows these products to be used throughout the European Economic Community Ce Measurements Specifications Output Power Maximum power per phase at full scale of voltage range Model Single Three Phase Phase 3000iL 3000 VA 1000 VA 4500iL 4500 VA 1500 VA 4800 VA Power Factor 0 to unity at full output VA Voltage Ranges Low 0 150 Volt Accuracy Resolution 1 mode 3 mode 45 5000 Hz 0 01 0 01 Hz 0 01 Hz Phase 100 Hz 0 1 0 1 100 5000 Hz 1 Voltage AC 0 300 V 0 05 250 mV 45Hz 1KHz A 0 05 0 05 KHz 250 mV 1 5KHz Apparent Power 0 5kVA 0 15 5 VA 0 15 3 VA 10 VA Aa E 0 00 1 00 Voltage Resolution 80 mV Accuracy specifications are in of reading For 4801iL measurement specifications apply in normal AC source mode of operation Model 4801iL is 1 mode only Load Regulation Less than 0 5 Line Regulation Less than 0 1 Programming Accuracy 25 C 5 C Voltage rms IEC Measurement Specifications 4801iL only so 6e0Hz 0 15 0 3 V 45 100 Hz Current Low range 1 0 20 3 500 5000 Ha 1 0 0 3 V 500 5000 Hz Hamonics2 49 0 03 AMA 0 2 KHZ_ Current High range Harmonics2 49 0 05 3 mA 0 2 kHz Reference Impedance o 0o4aand7o pH
11. modular construction and quality components the iL Series is designed to provide many years of uninterrupted service The modular construction allows components or subassemblies to be replaced quickly to minimize downtime All calibration functions can be performed from the front panel or one of the remote control interfaces without removing the covers making in place calibration possible iL Series Integrated IEC AC Test System Key benefits of the 48011L Model 480TiL is a special m Single box IEC AC test solution PC with IEEE 488 single phase version of the iL interface required Series that is optimized for Compliance with IEC 1000 3 2 EN 60555 2 and IEC 555 2 current harmonics and voltage quasi static and fluctuating current harmonic measurements flicker tests as specified in Compliance with IEC 1000 3 3 EN 60555 3 and IEC 555 3 IEC 1000 3 2 and IEC 1000 short term and long term voltage flicker measurements m Covers all load current requirements for products that 3 3 EN 60555 2 EN 6055 3 require IEC testing 230 Vrms 16 Arms single phase IEC 555 2 IEC 555 3 m Easy to use Windows Graphical User Interface for IEC The 4807iL delivers 16 test applications Amps in the 300 Volt range e Automatic test setup and unattended execution allowing it to be used to test e Automatic pre test for EUT class determination class A all AC source loads that fall B C or D for current harmonics under the IEC requirements e
12. nical support and service or to discuss your AC power application needs contact California Instruments Corp or your local representative Ordering Information Terms Net 30 days Delivery 30 days ARO F O B Factory San Diego CA Shipment Freight Collect Contact California Instruments Toll Free 800 4AC POWER 800 422 7693 FAX 858 677 0940 Email sales calinst com Web page http www calinst com W California Instruments 9689 Towne Centre Drive San Diego CA 92121 1964 858 677 9040 Copyright 1997 California Instruments Corp Specifications subject to change without notice FAX 858 677 0940 Printed in the USA iLSDS 3 97
13. r Windows 95 Harmonic and Flicker Test System program to support testing of AC loads for IEC 1000 3 2 and IEC 1000 3 3 requirements This program operates the 4801iL froma PC controller running all required tests automatically Test data is collected for archiving analysis and display iL Series For Easy Transient Programming Product Evaluation and Test Applications Increasingly manufacturers of electronic equipment and appliances are required to fully evaluate and test their products over a wide range of input line conditions The built in Line Distortion Simulation and load measurement system combines all needed source and measurement functions in an easy to use system Avionics Applications With an extended output frequency range of 5000 Hz Models 3000iL and 4500iL the iL Series is particularly well suited for aerospace applications Precise frequency control and accurate load regulation are key requirements in these applications The standard IEEE 488 control interface and SCPI command language provide for easy integration into existing ATE systems Since the iL Series can eliminate the need for three or four items of instrumentation cost and space savings provide a rapid return on investment Regulatory Testing As governments are moving to enforce product quality standards regulatory compliance testing is becoming a requirement for a growing number of manufacturers The 4801iL provides a cost eff
14. ser Interface can be used to operate the 4801iL in this ts normal mode of operation Er ar ar Oe PMNS Spake ener eee Harmen Number AA Graph Elapsed GO00020 Rerainng DROS ECCA PRT Folures 1S a2 Harmonics Generation and Analysis A peas tee mee Harmonic waveform 10 3 5 h t 7 and 9 MAIRAN Laz oat HH Simulation of severe ringing on the output of a UPS HHHH H H HH Voltage sweep transient causes output voltage to change at a programmed rate ae ee ooo Relative amplitude bar graph display of current harmonics o 5 E kaimai a Aamar ij D oman est AFE Colter inatromania te Bec le Daeg Fue eee ses ee ee hie Tes lt a Steady state control screen of GUI application program Harmonic Waveform Generation Using the latest DSP Digital Signal Processing technology the iL Series controller is capable of generating harmonic waveforms to test for harmonics susceptibility of a unit under test With the help of the supplied Windows Graphical User Interface program defining harmonic waveforms is as easy as specifying the relative amplitude and phase angle for each of up to 50 harmonics The waveform data points are generated and downloaded by the GUI to the AC source through either IEEE 488 or RS232C bus and remain in non volatile memory Up to twelve waveforms can be s
15. tored and given a user defined name for easy recall Arbitrary Waveform Generation Using the provided GUI program or custom software the user also has the ability to define arbitrary waveform data Any AC event can be simulated this way The GUI program provides a catalog of custom waveforms and also allows real world waveforms captured on a digital oscilloscope to be downloaded to one of the AC source s waveform memories Transient Programming To simulate common line disturbance occurrences the iL Series offers a list of 100 transient steps These steps can be programmed from the front panel or set using the GUI program supplied This allows the effect of rapid changes in voltage frequency phase angle and waveform shape on the unit under test to be analyzed Harmonic Analysis The measurement system is based on real time digitization of the voltage and current waveforms using a 4K sample buffer The digitized waveform data is used to extract conventional load values such as rms voltage rms current real and apparent power The same data is also used to perform Fast Fourrier Transformation FFT to extract the harmonic amplitude and phase angle of 50 harmonics up to 12 5 kHz Harmonic analysis data is available from the front panel or can be displayed saved and printed in tabular bar graph or time domain formats using the supplied GUI program Application Software Windows 3 1 application software is provided free of charg
Download Pdf Manuals
Related Search