Edge Instruction Manual
Contents
1. Please pay attention to the difference of inner and outer fixing part of frame The inner fixing part is with 5 holes 4 out of which has screw thread The middle hole of inner fixing part should face the center of screen It would cause failure in assembly if mistaking the inner and outer fixing part or the incorrect placement of it Please refer to diagram 4 for correct assembly b Please insert the base of supporting bar with inner fixing part mentioned above into the frame diagram 5 to join the 2 pcs of upper frames together Please be noted that the base of supporting bar should be inserted till it reaches the end to avoid any apparent seam between frames and the base of supporting bar c Assembly of outer fixing part for frame There are 4 holes in it and 2 gaps on the edge The gaps should face the center of screen diagram 6 Please put the outer fixing part onto the slot for snap lugs and adjust its position to match the holes of inner fixing part with screw thread Please fix the inner and outer fixing parts wit M5 8 screws diagram 7 d Assemble lower frame in the same way M5 8 screw Outer fixin p Aw part for frame Note The gaps should x ace the Insert into the frame center of screen Diagram 5 Diagram 6 Diagram 7 3 Installation instructions 3 Assembly of corner piece a Please insert corner piece into the slot of horizontal frame till it reaches the end There should2. off Note Please don t disassemble screen for replacement of parts Please kindly contact to after sale department for service if any fault It is not prior to notice if there is any change on product Please refer to the product Parts List m Left and right frames 2 pcs in equal length b m Up and down frames 4 pcs in equal length eo m Decoration cover for left and right frames 2 pcs in equal length a O m Decoration cover for up and down frames 4 pcs in equal length a iii m 5mm tension rods for left and right frames 2 pcs in equal length m 5mm tension rods for up and down frames 4 pcs in equal length Supporting bar 1 pcs m Mounting brackets with pre measured tether 1 set Screen fabric 1 pcs m Corner piece parts 4 sets m Cover for corner piece m Inner fixing parts for frame Outer fixing parts for frame 4 pcs 2 pcs 2 pcs l m Erecting rack for m Snap lug m M5 8mmscrew 24pcs m 3 8mm tapping screw supporting bar 4 pcs provided according 4 pcs to screen size ds amp m 5 40 tapping screw 4 pcs and expansion tube 4 pcs m User s manual 1 copy m Warranty card 1 set Qualification certificate 1 set 7 Assembly of screen fabric a Make sure the screen fabric is assemble in the place where is clean and tidy b Please put the rolled screen fabric onto frames with front side of fabric facing up then roll the fabric to spread slow
3. 0 Length of packing size Lg 917 1066 1166 1215 1315 1415 1489 1664 978 1139 1301 1409 1516 1597 1785 836 977 1070 1117 1210 1304 1374 1538 Installation instructions Open the package and take out all of the parts Kindly check the types and quantity of the parts according to user s manual Please put all of frames on clean and flat dest or ground in a square see diagram 1 Please pay attention to correct placement of aluminum frames the front side should be facing up while the inner side should be facing the center of the screen Please follow the order shown in diagram to assemble the frames i a dae ear a Upper frame U pper frame 4 pcs in equal length 4 pcs in equal length Snap lug BS Left frame 2 pcs in equal length Left frame 2 pcs in equal length Down frame Down frame 4 pes r length 4 pcs in equal length Diagram 1 1 Please put the snap lugs into lug s slot of frame see diagram 2 according to the Nos of holes in the screen fabric Inner fixing part for frame Insert into the hole Screw hole Screw hole Diagram 2 Diagram 3 Diagram 4 2 Joint of up and down frames a Put the inner fixing part for frame through hole on the base of supporting bar see diagram 3
4. 3 18 Tapping screw 785 M5 15 screw Erecting rack for Inner fixing part supporting bar M5 8 screw a 7 U _Slot for for snap lug x Outer fixing part gt a q lt w S ro le Base 6f l corner piece Corner piece Decoration cover M5 8 screw Corner piece components Sectional view of frame Fixing parts Sketch for structure of Edge fixed frame screen Note 1 Please pay attention to the rear and front sides of screen fabric during installation There is label attached to rear side of screen fabric Kindly handle with care to avoid distortion due to crash of the aluminum frame material In case of infrequent use please cover the screen fabric with cloth or something else fit to cover to prevent screen fabric from dusty Do not clear screen fabric with detergent of corrosivity such as diluent Please clean the velvet wrapped on the frame along the velvet grains Prevent velvet from crash to avoid damage Do not scrape screen fabric with fingers or edge tool which would leave flaws or marks on fabric In order to avoid any unexpected injury it is advisable to manage and install the fixed frame screen by adult Wn NOt Warning Regardless of the warnings would possibly lead to damage to product or casualty due to any improper operation Mandatory The screen should be installed where is strong enough to bear its weight or it would cause accident by falling
5. GRANDVIEW GRANDVIEW REPRODUCING GENUINE COLORS User s Manual for Large Flat Series Edge Fixed Frame Screen GRANDVIEW GRANDVIEW REPRODUCING GENUINE COLORS Grandview Crystal Screen Canada Ltd 11 3751 North Fraser Way Model F LF PExxx Marine Way Business Centre Burnaby BC Canada V5J 5G4 Tel 1 604 412 9777 Fax 1 604 412 9796 Website www grandviewscreen ca Thank you for purchasing a Grandview projection screen Guangzhou Grandview Crystal Screen Co Ltd Before use please read instructions carefully After installation store instructions for future reference P O 511400 Federal Ind Zone No 363 Yushan West Road Shiqiao Panyu District Guangzhou Guangdong China Tel 8620 8489 9499 Fax 8620 8480 3343 A Website www grandviewscreen com www grandviewscreen com cn CERTIFICATION Moopy 1S 09001 2000 International Certification Note Please make sure the concrete ceiling is strong enough to be bear the weight of 20kg or above in order to avoid any property lost and casualty due to insufficient bearing Product Structure Fixing parts Te Upper bracket Pre measured tether UP down ES Corner piece components Decoration cover Tension rod eet Tension rod Supporting bar Snap lug Screen fabric Lower bracket Left right frame amp Decoration cover Outer side j
6. a et F Si Pre measured Lower bracket tether Buckle Details A Details B Details C 7 7 7 35 Specification Inch qa See eee ae 60 72 80 84 92 100 106 120 60 72 84 92 100 106 84 92 100 106 120 Width of viewing size H_ 1328 1594 1771 1859 2037 2214 2346 2656 1292 1551 1809 1982 2154 2283 1963 2150 2337 2477 2805 Height of viewing size H 747 896 996 J 1045 1145 1245 1319 14941 808 969 1131 1239 1346 1427 835 915 995 1054 1193 Overall width of the screen Wa 1386 1652 1829 1917 2095 2272 2404 2714 1350 1609 1867 2040 2212 2341 2643 1460 1741 1928 2021 2208 2395 2535 2863 Overall height of the screen Hz 805 954 1054 1103 1203 1303 1377 1552 866 1027 1189 1297 1404 1485 1673 655 774 854 893 973 1053 1112 1251 Nos of snap lug for the up and down frame koh 6 8 10 10 12 12 12 4 6 8 0 10 2 2 4 6 8 ojoj 2 4 Nos of snap lug for the left and right frame Ks 4 6 6 6 6 8 8 8 4 6 6 6 8 8 8 4 4 4 5 6 6 6 6 Distance of up and down brackets Hgb 749 898 998 1047 1147 1247 1321 1496 810 971 1133 1241 1348 1429 1617 599 718 798 837 917 997 1056 1195 Length of bracket Leb 800 800 800 1000 1000 1000 1000 1200 800 800 1000 1000 1000 1000 1200 800 800 800 800 1000 1000 1000 120
7. ly diagram 19 c Please put the tension rods through 4 edges of fabric Please be noted that the 2 pcs of left and right tension rods are in the equal length so are the 4 pcs of up and down tension rods d Adjust distance from snap lugs according to the snap lugs s holes at the edges of fabric then hold the fabric with hands to put the snap lugs go through the holes diagram 21 It is advised to handle the snap lugs on up and down frames Snapping from middle to edges e Please make necessary adjustment on fabric to keep it smooth and flat from wrinkles Diagram 19 Diagram 20 Diagram 21 8 Installation of cover for corner piece and frame a Mount the cover for corner piece onto the slot of base and use 13 8mm tapping screws to fix it diagram 22 b Mount the frame cover with rubber onto the frame and press it down in position until it is tight see diagram 23 24 The frame cover with label should be placed onto lower right corner at the front side of screen Press down to make it Corner Frame decoration cover tapping screw Press down and make it tight Diagram 22 Diagram 23 Diagram 24 9 Assembly of bracket set and mount the screen onto wall a Please find out the position to put the screen and drill holes in wall according to the mounting holes of bracket Please fix the bracket onto wall with the expansion tubes and screws provided b Please let the lower bracket drop naturally and i
8. not be any apparent seam found Please use M5 8 screw to fix it see diagram 8 10 b Assemble other corner piece in the same way M5 8 screw upper or lower frame Base of F corner piece Corner piece Insert into the slot Diagram 8 Diagram 9 Diagram 10 4 Join the frames together a Please insert the other side of corner piece into the vertical frame till it reaches the end There should not be any apparent seam found Kindly use M5 8 screw to fix it see diagram 11 12 b Join the other vertical frame with up and down frame in the same way see diagram 13 M5 8 screw Horizontal frame Diagram 11 Diagram 12 Diagram 13 5 Assembly of supporting bar Attach the supporting bar with the erecting rack along the extending part on it till it reaches the end and the hook would clip into the square hole in the supporting bar see diagram 14 15 Note It is not advise to disassemble or assemble the supporting bar frequently If it is necessary please use the flat screw driver to insert into square hole in supporting bar to unlock the hook for disassembly see diagram 16 Supporting bar Erecting rack for supporting bar Square hole Hook erecting rack along the extending pan T Erecting rack for aie Use flat screw bar Hook gt driver to unlock Fee the 8 the hook at k supportini Supporting A bar with bar J Diagram 14 Diagram 15 Diagram 16 6 Join the other set of h
9. orizontal frame Join the other set of horizontal frame with the vertical frames with screw in the same way as the step 4 and step 5 mentioned above see diagram 17 18 Please check it again to see if all of the screws are tighten ee Diagram 17 Diagram 18
10. t would be in position with help of the pre measured tether Please mark the position of mounting holes for lower bracket drill the holes and fix the lower bracket with expansion tubes and screws provided c Measure distance from upper and lower brackets which should be H 2mm Please make necessary adjustment if the distance doesn t meet the above d Turn the buckle on lower bracket counter clockwise until it reaches the end to make the lock mark on the buckle stops at direction of 12 or 3 o clock upright or right position to make it unlock see diagram 26 e Please mount the screen onto brackets Make sure hooks of brackets go in the slots of up and down frames see diagram 27 28 f Please finish the installation by turning the buckle clockwise until it reaches the end to lock the lower frame see diagram 26 on the right and diagram 29 Wall Upper bracket Pre measured tether Diagram 26 Diagram 27 In unlock In lock condition condition lower bracket Diagram 25 Diagram 28 Diagram 29 Overall view and dimension aon A Upper frame 1 Upper frame 2 Details B Distance of up and down brackets Hgb ioe Lo rf i WI s Wz W 58 Details C Length of bracket Lgb 38 5 4 iS P at 32 Pre measured tether ad Upper bracket mj iB O
Download Pdf Manuals
Related Search