OWNER`S MANUAL - Bowtech Archery
Contents
1. 4 At this point the string and or cable can be removed from the cam 5 Upon replacing the string and or cable back onto the cam and idler clevis pulleys double check all the string and cable post connections as well as tracks to ensure they are seated properly 6 Once all double checks are made reverse tension adjustment as described above Again make sure to tighten each limb bolt in small increments alternating from top to bottom limb bolt until reference point is achieved Make sure to keep hands clear of cam and idler while tightening the limb bolts WARNING DO NOT TURN LIMB BOLTS OUT MORE THAN THE RECOMMENDED AMOUNT WHEN SHOOTING YOUR BOW Doing so could result in bodily injury Measure Here s Measure Figure 5 Determining Center Shot BOW MAINTENANCE Your Diamond bow was made with the highest quality components to last for a lifetime of use in the field with proper maintenance It is important that you NEVER draw and release a bow without an arrow on the string This could not only hurt you but can damage your bow If the bow is dry fired at any time take it to your local Authorized Diamond Dealer for a complete inspection Never leave your Diamond bow in an area of extreme temperatures This will cause your string and cables to stretch which effects timing Before shooting your bow always inspect the string and cables and check the limbs for any visible damage If damage is found take the bow to your lo2. OWNER S RECORD Date of Purchase __ gt ___ESSSSSSCS Purchase Price Bow Model amp Year Brace Height Draw Length Draw Weight IBO Speed Rating String Length ____ Cable Length Dealer Purchased From Dealer s Address City State Zip Phone No Email Address We encourage you to contact and utilize your local Authorized Diamond Dealer as they can assist you with purchases services and accessories To locate the dealer nearest you visit DiamondArchery com and click on the Dealer Locator button Frequently asked questions and additional contact information can also be found at DiamondArchery com SIGN UP FOR THE LIFETIME WARRANTY AT REGISTERYOURBOW COM Every effort has been made to ensure the accuracy of information and typographical content within our owner s manual Diamond reserves the right to modify and or discontinue products without notice and at its discretion 2013 Diamond Archery by BowTech All rights reserved
3. by abuse mishandling dry firing alteration or modification to original through an Authorized Dealer LIFETIME WARRANTY Warranty Service Our goal with all warranty returns is to have obtained by your dealer Bows returned to the factory without an RA number will not be the bow shipped out the door and on its way accepted back to your dealer within 3 business days of receiving it at our facilities in Eugene Oregon You are our greatest asset and we will give you the highest quality and most efficient service possible The bow owner is responsible for the return prepaid freight to Diamond No COD shipments will be accepted Diamond will perform the warranty service required and return the product to the dealer prepaid All methods of shipping by UPS or FED EX only Sender should insure all shipments All products requiring warranty service must be returned to an Authorized Dealer for inspection and diagnosis of any problem Your Diamond Dealer can determine whether factory service is required or if the service needed can be performed at the dealer s facility In the event that a bow must be returned for factory service a Return Authorization RA number must first be If your bow cannot be repaired we reserve the right to replace your bow with a newer model of equal or greater value Diamond reserves the right to substitute any parts required for warranty coverage at its sole discretion and for any
4. mark on the cam is aligned with a lower numbered indexing mark on the module For example if an Outlaw was shipped with the indexing mark in the 2 5 position at 29 inches of draw length you would place it in the 1 5 position for a 30 inch draw length 5 To shorten the draw length rotate the module so that the indexing mark on the cam is aligned with a higher numbered indexing mark on the module For example Chart 1 Cam Module amp Post Settings if an Outlaw was shipped with the indexing mark in the 2 5 position at 29 inches of draw length you would place it in the 3 5 position for a 28 inch draw length 6 Replace both module screws on each cam and retighten We recommend applying blue Loctite 242 to the threads before replacing them at your desired setting This will prevent the screws from loosening during normal use of the bow 7 After repositioning the module you will need to reposition the draw stop posts To do this use a 3 32 inch hex wrench to remove the post from its current position 8 Replace the post in the position that matches the position that you placed the module in For example if the module was placed in the 3 position the draw stop post should also be placed in the 3 position 9 Please note that no bow press is typically required to change the draw length of your Diamond bow However placing the module in the 5 position may require the use of a bow press Module Position Draw Leng
5. will perform best when shot with a release ADULT SUPERVISION OF ALL CHILDREN UNDER THE AGE OF 18 IS REQUIRED Diamond has designed your bow to be a safe and fun product However as with any shooting style product safety rules must be observed It is HIGHLY recommended that these rules be read before using any bow Bows and arrows are NOT toys For maximum safety and enjoyment always exercise caution and common sense when shooting any bow WARNING NEVER DRY FIRE THE BOW SAFETY AND GENERAL INFORMATION NEVER draw a bow without an arrow nocked Doing so could cause personal injury and or damage the bow When drawing a bow for inspection or demonstration never release the string at full draw to let down Hold onto the string and do not let it slip out of your hands Without the resistance of a properly weighted arrow to absorb the energy you may damage the bow and cause personal injury to yourself and or others ALWAYS wear safety glasses when operating or adjusting your bow ALWAYS use an appropriate backstop for maximum safety An appropriate backstop must be constructed of a durable material and must extend beyond the perimeter of the target The recommended backstop size is determined by the accuracy and ability of the shooter With a low level of shooter accuracy the backstop perimeter requirement must be increased appropriately NEVER aim or draw any bow in the direction of a person Aim and draw ONLY in the direct
6. THANK YOU Congratulations on your recent purchase We at Diamond know that you have a choice when it comes to your archery equipment and we want to thank you for choosing us as your hunting partner Your feedback is important to us as it is our desire to provide you with the absolute finest products and customer service in the industry Please take the time to go online and register your new Diamond bow It is equally important to read through this owner s manual as there are valuable tips to help keep your Diamond trouble free for many seasons We encourage you to contact and utilize your local dealer as they can assist you with purchases services and accessories To locate the dealer nearest you visit DiamondArchery com and click on the Dealer Locator button Frequently asked questions and additional contact information can also be found at DiamondArchery com OWNER S MANUAL BEFORE USING YOUR NEW DIAMOND BOW READ AND UNDERSTAND THE FOLLOWING MATERIAL OUTLINED IN THIS MANUAL FAILURE TO FOLLOW ANY OF THESE WARNINGS AND INSTRUCTIONS CAN DAMAGE THE BOW AND MAY CAUSE SERIOUS INJURY TO YOURSELF AND OR OTHERS DISCLAIMER OF LIABILITY By accepting a Diamond product the buyer agrees to hold harmless Diamond and all associated parties from liability for any damage to persons or property which may result for any reason from the use of this product QUALITY a Every Diamond bow has undergone a comprehensive quality control pro
7. cal Authorized Diamond Dealer for inspection or repair Your Diamond bow comes equipped with sealed bearings for both the cam and idler There is no need to lubricate the bearings STRING amp CABLES Your Diamond custom bowstring is manufactured to provide long string life and absolute consistency shot after shot This results in greater accuracy and less time spent re tuning your equipment It is recommended that you cycle the bow 10 20 times to settle the string as a result of relaxation during packaging and shipping Wax the string often We recommend BCYML 6 synthetic string wax or an equivalent product To wax the string apply wax liberally to entire length of string Rub briskly with fingers until the string appears slick Remove all excess wax with a clean cloth We recommend that you wax every other time you shoot your bow to lengthen the life of your string and cable sets If you need assistance with setting up tuning or solving an arrow flight problem contact your Authorized Diamond Dealer SAFETY AND GENERAL INFORMATION Your new Diamond bow is a highly tuned precise shooting machine It requires special care and handling to achieve and maintain peak performance The string cables and limbs are under extreme tension which creates an incredible source of energy that must not be taken for granted Please respect this power and use it properly Diamond bows are standardized to fit most manufacturers accessories and
8. cess and is built from the highest quality components available Most have been individually shot tested and measured to ensure compliance with our strict performance standards Pe l AAAs EF yei z f Be LENE ile LIFETIME WARRANTY All Diamond bows come with a non product Other excluded damages are those transferable lifetime warranty to the registered original owner This warranty protects against any failures of the product due to defects in material or workmanship and does not resulting from either loose module screws or shooting arrows less than five grains per pound of draw weight For the warranty to be enforceable the a include any damage due to abuse misuse iT ee original purchaser must complete and submit or modification to the bow s design The el the online registration form within 30 days of following exclusions apply purchase Exclusions Authorized Dealer Strings and cables bearings paint and or se The Diamond Warranty covers product hydrographic film transferred finishes purchased from Authorized Diamond Dealers accessories to include sights arrow rests Diamond products purchased through the string silencers quivers or any other i Internet will not be warranted if not purchased components included as part of an accessory i through an Authorized Dealer Contact package E o E oe 4 WF o a ee E hii Diamond to confirm that your purchase is Damage caused
9. ion of an appropriate target ALWAYS have a full view of the path to and beyond the target when shooting ALWAYS check all arrow components prior to shooting including nock insert and tip Loose components can cause unbalanced arrow flight and partial dry firing of the bow If an arrow has been damaged or if you believe it has been damaged do not shoot it again as it could break on release and sharp arrow pieces could strike and injure you or someone nearby NEVER retrieve arrows or allow anyone else to do so until all arrows have been shot NEVER draw the bow without properly adjusted limb bolts see Adjusting Draw Weight section for more information Make sure the string and cables are properly attached to the correct post and in the correct tracks in order to avoid possible injury DO NOT attach anything to the cables or string that could create excessive wear or slice the string material This will void the warranty DO NOT cross cables in any configuration other than the configuration set by the factory This will have an adverse effect on the performance and shootability of your bow Further it may cause extreme wear to the string cable and cable slide roller guard Any alteration from the factory specifications or the adjustments outlined herein will void the factory warranty ALL maintenance must be performed at an Authorized Diamond Dealer DIAMOND ARCHERY BY BOWTECH DiamondArchery com
10. n before proceeding to the next turn of the limb bolt Please consult your Authorized Diamond Dealer before making this adjustment 1 Before adjusting limb bolts note setting on limb bolt adjustment marks for future reference See Figure 4 2 When proceeding to break down your Diamond Core bow turn the limb bolts in small equal increments alternating from the top limb bolt to lower limb bolt until the tip of the limb bolt is visible in the reference hole DO NOT draw bow back or shoot the bow when the limb bolts are backed out past the limb bolt reference hole 3 Once limb bolt tip is visible continue to turn out limb bolts in same manner as above until 5 6 complete revolutions are made on each end Check string and cable tension If slack stopping point is achieved If still under tension turn each limb bolt an additional revolution CENTER SHOT Center shot can be set by measuring from the back of the riser to the arrow and then from the front of the riser to the arrow Once this is equal you are at the approximate center shot of your bow see Figure 5 This is a good starting point when tuning your Diamond bow Keep in mind not all bows tune at exact center shot due to the variances in arrow spine hand position and your specific bow poundage Adjust your arrow rest until the two measurements are equal Limb Bolt Adjustment Marks Limb Bolt Inspection Hole Figure 4 Draw Weight Adjustment Core
11. reason ADJUSTING DRAW LENGTH It is very important that your Diamond bow is adjusted to fit you properly Assistance in achieving a proper fit should be provided by your Authorized Diamond Dealer Diamond bows are preset to factory specifications with adult models preset to 29 inches draw length You may need to adjust your bow to match your draw length Any other alterations to the factory setup will likely inhibit performance The draw length of all current Diamond bows can be adjusted without draw length specific modules The Rotating Mod System makes this feature possible By simply rotating the module clockwise or counterclockwise your draw length can be adjusted typically in 1 2 inch increments Refer to Figure 1 and Chart 1 Module Screws Cam Indexing Mark Module Indexing Mark Figure 1 Draw Length Adjustment 3 ADJUSTING THE DRAW LENGTH conrT 1 Diamond recommends that you take your bow to your Authorized Diamond Dealer for adjustment of your bow s draw length 2 Use a 3 32 inch hex wrench to remove the module screws that attach the modules to the cams 3 Notice the numbered indexing mark on the module and the indexing mark on the cam All bows are factory preset to a 29 inch draw length with the indexing marks aligned for the this draw length setting The lowest numbered mark corresponds to the longest draw length setting 4 To lengthen the draw length rotate the module so that the indexing
12. th Module Post Setting 4 O a O Pe or 1 1 5 2 2 5 3 3 5 4 os 5 5 5 Draw Length Setting E e E et e a ca ss O s O LS et 5 CAM TIMING There are small indentations or timing marks on the module side of the cam near its perimeter When viewing the bow directly from the module side of the cam the cable should be approximately centered in between the timing marks as shown in Figure 2 Adjusting the timing requires that the bow be put in a press and as such your Authorized Diamond Dealer should perform all timing adjustments Cable Centered Between Marks Figure 2 Cam Timing SETTING THE DRAW WEIGHT Limb Bolt Inspection Hole Figure 3 Draw Weight Adjustment Outlaw Draw weight can be adjusted by using a hex wrench to either tighten or loosen the limb bolt The specific method for adjusting draw length varies by model as described below WARNING DO NOT TURN THE LIMB BOLTS OUT MORE THAN THE RECOMMENDED AMOUNT Doing so could cause the limbs to break out of their pockets and result in bodily injury Outlaw Draw weight on these models can be adjusted 10 pounds down from the bow s peak draw weight For example if the bow is shipped as a 60 pound model the draw weight can be adjusted down to 50 pounds The procedure is as follows see Fig 3 5 Using a hex wrench tighten or loosen the limb bolts to increase or decrease draw weight For the Outlaw one t
13. urn of the limb bolt equals approximately 2 5 pounds DO NOT back out the limb bolt past the limb bolt inspection hole in the riser The limb bolt MUST BE visible in the limb bolt inspection hole The top and bottom limb bolts should be tightened and loosened equally Core Draw weight on these models can be adjusted 30 pounds down from the bow s peak draw weight For example the bow is shipped at 70 pounds and the draw weight can be adjusted down to 40 pounds The procedure is as follows see Fig 4 Using a hex wrench tighten or loosen the limb bolts to increase or decrease draw weight For the Core one turn of the limb bolt equals approximately 3 0 pounds DO NOT back out the limb bolt past the limb bolt inspection hole in the riser for the application of shooting your bow The limb bolt MUST BE visible in the limb bolt inspection hole The top and bottom limb bolts should be tightened and loosened equally The Diamond Core comes with the ability to break down your bow without a bow press This can be useful for changing out your string SETTING THE DRAW WEIGHT cont and or cable if you are in a location where a bow press is unavailable To accomplish the break down of your Diamond Core bow each limb bolt may be backed out an additional 5 6 complete turns in order to relieve the string and cable tensions enough to remove the string and or cable It is recommended that each limb bolt is backed out evenly per each tur
Download Pdf Manuals
Related Search