W315A/325A User`s Manual
Contents
1. insert the SD memory SIM Card Slot SD Card Slot card into the slot 3 5 A Regulatory Approval Statement This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Class A FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense C European Community Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device mu2. RJ45 to RJ45 cross over cable 100 cm e CBL APINDB9F 100 4 pin pin header to DB9 female console port cable 100 cm e GSM GPRS antenna e Documentation and software CD e Quick installation guide printed e Warranty card Optional Accessories e 35 mm DIN rail mounting kit DK 35A NOTE Please notify your sales representative if any of the above items are missing or damaged 1 2 W315A 325A Introduction Product Features W315A 325A series embedded computers have the following features e MOXA ART 32 bit ARMY RISC industrial communication processor e 16 MB built in flash memory e RS 232 422 485 serial ports with software selectable interface e Baudrate between 50 and 921 6Kbps supports non standard baudrates e 10 100M Ethernet for backup networking e Built in quad band 850 900 1800 1900 MHz GSM GPRS module e GPRS class 10 e Coding scheme from CS1 to CS4 e SD card slot for storage expansion e Designed to withstand continuous 5G vibration and a 50G shock e LED indicators for status serial transmission and wireless signal strength e Ready to run Linux platform e Can be installed on a DIN Rail or wall mounted e Fanless design for increased ruggedness Hardware Specifications Computer CPU MOXA ART ARM9 32 bit RISC CPU 192 MHz OS pre installed Embedded Linux with MMU support DRAM 32 MB Flash 16 MB Storage Storage Expansion SD slot Ethernet Interface LAN 1 auto sensing 10 100 Mbps port RJ45 Magn
3. SIM Card P Installing an SD Card for Storage Expansion W315A 325A Hardware Connection Description Installing the W315A 325A Wall or Cabinet Mountin The W315A 325A embedded computers have built in ears for attaching the embedded computers to a wall or the inside of a cabinet V V RESET LAN 12 48V We suggest using two screws per ear to attach the W315A 325A to a wall or cabinet The heads of the screws should be less than 6 0 mm in diameter and the shafts should be less than 3 5 mm in diameter 6 0 mm h L 3 5 mm RS 232 422 485 P1 DIN Rail Mounting DIN rail attachments can be purchased separately to attach the product to a DIN rail When snapping the attachments to the DIN rail make sure that the stiff metal springs are at the top Wiring Requirements In this section we describe how to connect serial devices to the embedded computer Read and follow these common safety precautions before proceeding with the installation e Use separate paths to route wiring for power and devices If power wiring and device wiring paths must cross the wires should be perpendicular at the intersection point NOTE Do not run signal or communication wiring together with power wiring in the same wire conduit To avoid interference wires with different signal characteristics should be routed separately e Use the type of signal transmitted through a wire to determine which wires should be kept sepa
4. Toll free 1 888 669 2872 Tel 1 714 528 6777 Fax 1 714 528 6778 Moxa Europe Tel 49 89 3 70 03 99 0 Fax 49 89 3 70 03 99 99 www moxa com su ort Moxa China Shanghai office Toll free 800 820 5036 Tel 86 21 5258 9955 Fax 86 10 6872 3958 Moxa Asia Pacific Tel 886 2 8919 1230 Fax 886 2 8919 1231 Table of Contents Be 2ENCFOGUCUOR o 05 5052211051 1005 7217023102 2101552321001220 1152255031205 251051052 250571522510515215 3015102550570 25 1 1 OVelVIOW acvprENPEENEEPEPEENEENMFENMEENMERNMPRNMNENRENERENPNENENENENENNENMNNNMNNMNNNMNNMNNNMNNNMNNNMNNNMNNNMNNKMNNNMNNNMNNNMNNNMNNNMNNMN MEE 1 2 Package Bn To dicis 1 2 gereltToMiu ciulI m TI D aa a a aa Aaa A A AAT a 1 3 IEE e eega ola eS E E m AT 1 3 HardWare BIOGK Diag arns surs ninna Naana a a aSa a Nae aea aAA aAa A Aaa codec adu fva A A 1 5 WS LSA a E aE E E ee 1 5 WOZU Mu 1 5 2 Hardware Introduction ice nexu wi i MEM SUE MEAM CENA MEUM EMEN MT UEM MEM CR Wale IUE CEU US 2 1 asi 0SR w G 0 SGSSA S 0 SG A m 2 2 Cis Ver eee eee ere eT ska aad dadas a N tasti Faits aiunt ade baut soa Fait a be cata rrr 2 2 E PaT ENIM EA MM MR MEM IE MM EE 2 2 DIMENSIONS rarer anlar rch ane archaea eletti ERE 2 3 EED RIVE Salat cht isopod aa escalate cg cal ag ad al a cg ag calcu cad cal rl E ecco ag 2 3 Reset BUCOM uiis1339553 98 8 9OEPDPEPNPRISUROGUGSDND SN II AGA Ga RUMP RLGDR AS NAR A GG GN RDBD S PIG R RA a dH ORDRIG IRIS a
5. M provide ample storage capacity and the SD slot gives applications extra room to expand The built in GSM GPRS function supports the 850 900 1800 1900 MHz frequency bands providing a coding scheme from CS 1 to CS 4 The backup LAN port not only provides an alternative solution for networking but also supports Ethernet clients allowing any network device to plug in and connect to the GPRS network The built in RS 232 422 485 serial ports support a wide range of serial devices making this platform suitable for data acquisition and protocol conversion applications The Linux based operating system comes pre installed and ready to run providing an open platform for software development Software written for desktop PCs can be ported easily to W315A 325A series embedded computers by using a common compiler so you do not need to spend a lot of time modifying existing software code In addition the operating system device drivers and user developed software can all be stored in the built in flash memory Package Checklist The W315A 325A Series includes the following models W315A LX Mini RISC based ready to run wireless embedded computer with GSM GPRS one serial port LAN SD and Linux OS W325A LX Mini RISC based ready to run wireless embedded computer with GSM GPRS two serial ports LAN SD and Linux OS Each model is shipped with the following items e W315A or W325A embedded computer e Wall mounting kit e Ethernet cable
6. W315A 325A User s Manual Second Edition March 2011 www moxa com pr t MOXA 2011 Moxa Inc All rights reserved W315A 325A User s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement Copyright Notice 2011 Moxa Inc All rights reserved Trademarks The MOXA logo is a registered trademark of Moxa Inc All other trademarks or registered marks in this manual belong to their respective manufacturers Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa Moxa provides this document as is without warranty of any kind either expressed or implied including but not limited to its particular purpose Moxa reserves the right to make improvements and or changes to this manual or to the products and or the programs described in this manual at any time Information provided in this manual is intended to be accurate and reliable However Moxa assumes no responsibility for its use or for any infringements on the rights of third parties that may result from its use This product might include unintentional technical or typographical errors Changes are periodically made to the information herein to correct such errors and these changes are incorporated into new editions of the publication Technical Support Contact Information Moxa Americas
7. a ate nea a ence AAAA 2 4 Real TIMEGO K umen n n n n 2 4 3 Hardware Connection Description rrrruuuiisunnnnunnnnnuuuuuaaa hn mrrsuuuuu uu y ys rmuuuuu uu uon na 3 1 Ipstallno the WISA ATP EL ww 3 2 Wining REQGUIFEIMENLS meme n X 3 2 Connecting the POWOl tai uev eu m ic UC MIELE ee MM Ee E MUT 3 3 Grounding the UNE lt tsrccestassescenedevedstadavadavedabadavedisadavedstadawadavedaadnradabadavedstadavedavedaiadnedabadamcoedanes 3 3 Connecting Data Transmission Caples eransi iad anak manera tad aad vr aed stant ad nia Eae nian tu etn aia htt 3 3 COMMS CEI ro she NGEWO K oso oso ant ette anam demum ma dem MuR dutem de mM dm EINE 3 3 Connecting toa Seral DViCO soii naana dex Pus Fides teu tiri ciexPxeordex desi ded bestdndcdei decode doce dad dai e eds 3 4 Colinectihga to xhe Serial Console BOE eani a M GRADUUM eto AE URL AERA OL oA UR E ce ae 3 4 Connecting e ATEeTnPriems eas er dox rer er RR 3 4 Iristallibge a deed LRGs fo eT eT re ede 3 5 Installing an SD Card Tor Storage EXPANSION swwdescsinnhsosdaeadienlimanandntinahiadea dedicated edad d edad vdd 3 5 A Regulatory Approval StatemenL u xcisuu ux SuERSESEFRERSREREESENNERVEEENEEREEEFENEENFEEESENVEREREENNREREEEKFMEEEEEENNERNNEEEEEKSSERERE A 1 1 Introduction The W315A 325A wireless RISC based embedded computers feature a GSM GPRS module RS 232 422 485 serial ports and an Ethernet port in a small rugged chassis In addition the W315A and W325A come w
8. age Temperature 20 to 80 C 4 to 176 F Anti vibration 5 g IEC 68 2 6 sine wave 5 500 Hz 1 Oct min 1 hr axis Anti shock 50 g IEC 68 2 6 half sine wave 30 ms Power Requirements Input Voltage 12 to 48 VDC Power Consumption Without GPRS loading 4 8 W e 100 mA 48 VDC e 200 mA 24 VDC e 400 mA 12 VDC With GPRS loading 12 W e 330 mA 48 VDC e 540 mA 24 VDC e 1000 mA 12 VDC e 200 mA 24 VDC e 400 mA 12 VDC Regulatory Approvals EMC CE EN55022 Class A EN61000 3 2 EN61000 3 3 EN55024 FCC Part 15 Subpart B CISPR 22 Class A ANSI C63 4 Safety UL cUL UL60950 1 LVD EN 60950 1 R amp TTE EN301 489 1 EN301 489 7 EN301 511 Safety LVD EN60950 1 UL cUL UL60950 1 CSA C22 2 No 60950 1 03 Green Product RoHS CRoHS WEEE Reliability Alert Tools Built in buzzer and RTC real time clock with battery backup Automatic Reboot Trigger Built in WDT watchdog timer Warranty Warranty Period 5 years Details See www moxa com warranty 1 4 W315A 325A Introduction Hardware Block Diagrams W315A Ethernet GSM GPRS Watchdog i AN RS 232 422 485 RS 232 W325A Ethernet GSM GPRS a o b k Hs inim RS 232 422 485 RS 232 2 Hardware Introduction The W315A 325A series embedded computers are compact well designed and built rugged enough for industrial applications LED indicators help you monitor performance and identify trouble spots mu
9. card is not detected GPRS Green ON GPRS is ready a Conflict with GPRS IP or no response from DHCP server Of GPRS is not ready or function error exists Signal Strength Number of glowing LEDs indicates signal strength Excellent Very good Good Fair 10 Mbps Ethernet link s 100 Mbps Ethernet link Off Disconnected or short circuit ia ports P1 P2 transmitting data Of Serial ports P1 P2 not transmitting data a ports P1 P2 receiving data Off Serial ports P1 P2 not receiving data 2 3 W315A 325A Hardware Introduction Reset Button Hold in the reset button for 5 seconds to load the factory default configuration After loading the factory defaults the system will reboot automatically We recommend that you use this function only if the software is not working properly To reset the Linux system software always use the software reboot command reboot to protect the integrity of your data The reset button is NOT designed to hard reboot the embedded computer ATTENTION Restoring default settings preserves your data Resetting the embedded computer to factory defaults will format the user directory and erase the contents in etc and home The reset button only loads a configuration file All files in the etc directory will revert to their factory defaults Note that if there is a problem with the etc directory the embedded computer may be unable to restore the factory default settings Real T
10. device into the embedded computer s serial port Serial ports P1 to P2 have male DB9 connectors and can be configured for RS 232 RS 422 or RS 485 communication by software The pin assignments are shown in the following table DB9 Male Port RS 232 422 485 Pinouts 1234 5 RS 485 RS 485 ZION wire wire au 1 a pon poro TxDB TxDB mo eose RxDB DataBC 6789 BTR RxDAC RxDAC DataAC Connecting to the Serial Console Port The serial console port is a 4 pin pin header RS 232 port It is designed for serial console terminals which are useful for viewing boot up messages Serial Console Port amp Pinouts Serial Console Cable Connecting an Antenna The W315A 325A embedded computers come with a 1 dBi antenna for GPRS communication Connect the antenna to the SMA connector located on the front panel of the embedded computer Connect the antenna to the computer by rotating it in a clockwise direction Antenna Connector GSM GPRS Antenna W315A 325A Hardware Connection Description Installing a SIM Card The W315A 325A embedded computers have a built in GSM GPRS cellular module to provide long range communication SIM Subscriber Identity Module cards are used to authenticate and identify subscribers when connecting to a network Follow these steps to install a SIM card Stepi Before you install a SIM card make sure the embedded computer is powered off Step2 Use a screwdriver to r
11. ell grounded mounting surface such as a metal panel SG SG The Shielded Ground sometimes called Protected Ground contact is the left most contact of the 3 pin power terminal block connector when viewed from the angle shown here Connect the SG wire to an appropriate grounded metal surface Connecting Data Transmission Cables In this section we describe how to connect the W315A 325A embedded computers to the network serial devices and a serial COM terminal Connecting to the Network Plug your network cable into the embedded computer s Ethernet port The other end of the cable should be plugged into your Ethernet network When the cable is properly connected the LEDs on the embedded computer s Ethernet port will glow to indicate a valid connection The 10 100 Mbps Ethernet LAN port accepts 8 pin RJ45 connectors The following diagram shows the pinouts for these ports The LED indicator on the right glows a solid green color when the cable is properly connected to a 100 Mbps Ethernet network The LED will flash on and off when Ethernet packets are being transmitted or received The LED indicator on the left glows a solid orange color when the cable is properly connected to a 10 Mbps Ethernet network The LED will flash on and off when Ethernet packets are being transmitted or received W315A 325A Hardware Connection Description Connecting to a Serial Device Use a serial cable to plug your serial
12. emove the protective cover to access the slot Note that the SD slot and SIM card slot for the W315A 325A share the same protective cover Step3 When inserting the SIM card make sure the chip is facing SIM Card Slot SD Card Slot upwards Plug the SIM card directly into the slot Step 4 Power on the embedded computer and start the operating system Step 5 To operate GPRS connection refer to the operating system user s manual for details NOTE To remove the SIM card from the slot press the SIM card in slightly with your finger and then remove your finger to allow the card to spring out partially You may now grasp the top of the card with two fingers and pull it out Installing an SD Card for Storage Expansion The W315A 325A embedded computers have an SD slot for storage expansion The SD slot allows users to plug in a Secure Digital SD memory card compliant with the SD 1 0 standard for up to 1 GB of additional memory space or a Secure Digital High Capacity SDHC memory card compliant with the SD 2 0 standard for up to 16 GB of additional memory space The following steps show you how to install an SD card The SD slot is located on the right side of the W315 W325 casing To install an SD card first remove the protective cover to access the slot and then plug the SD card directly into the slot Step 1 Use a screwdriver to remove the screws holding the SD SIM card slot s outer cover Step 2 After removing the cover
13. etic Isolation Protection 1 5 KV built in Cellular Interface Cellular Modes GSM GPRS Radio Frequency Bands 850 900 1800 1900 MHz GPRS Class 10 Coding Schemes CS1 to CS4 Serial Interface Serial Standards 1 or 2 RS 232 422 485 ports software selectable DB9 male ESD Protection 15 KV ESD protection for all signals Console Port RS 232 interface TxD RxD GND with 4 pin pin header output Serial Communication Parameters Data Bits 5 6 7 8 Stop Bits 1 1 5 2 Parity None Even Odd Space Mark Flow Control RTS CTS XON XOFF ADDC automatic data direction control for RS 485 Baudrate 50 bps to 921 6 Kbps non standard baudrates supported see user s manual for details Serial Signals RS 232 TxD RxD DTR DSR RTS CTS DCD GND RS 422 TxD TxD RxD RxD GND RS 485 4w TxD TxD RxD RxD GND RS 485 2w Data Data GND 1 3 W315A 325A Introduction LEDs System Ready SD LAN 10M Link 100M Link on connector Cellular GPRS Enabled GSM Signal Strength Serial TxD RxD Switches and Buttons Reset Button Supports Reset to Factory Default Physical Characteristics Housing Aluminum 1 mm Weight 195 g Dimensions without ears or antenna 77x 111 x 26 mm 3 03 x 4 37 x 1 02 in Mounting DIN rail requires optional DK 35A DIN rail kit wall Antenna Length 84 mm Environmental Limits Operating Temperature 10 to 60 C 14 to 140 F Operating Humidity 5 to 95 RH Stor
14. ime Clock The embedded computer s real time clock is powered by a lithium battery We strongly recommend that you do NOT replace the lithium battery on your own If the battery needs to be changed contact the Moxa RMA service team WARNING There is a risk of explosion if the wrong type of battery is used To avoid this potential danger always use the correct type of battery Contact the Moxa RMA service team if you need to replace your battery Dispose of used batteries according to the instructions on the battery 2 4 3 Hardware Connection Description The W315A 325A wireless embedded computers support multiple connection types GSM GPRS Ethernet and one or more serial ports are built into every model In addition the computers come with a serial console port for monitoring bootup messages All models include an SD storage socket for additional device and storage options With the open source Linux kernel you are free to develop custom applications for remote wireless operation of your device In this chapter learn how to connect the embedded computer to the network and to various devices The following topics are covered in this chapter 0 Installing the W315A 325A 0 Wiring Requirements gt Connecting the Power gt Grounding the Unit O Connecting Data Transmission Cables Connecting to the Network gt Connecting to a Serial Device gt Connecting to the Serial Console Port Connecting an Antenna 0 Installing a
15. ith an SD socket making them the ideal solution when the applications require external storage expansion The W315A 325A embedded computers are ideal for diverse machine to machine embedded applications The computers enable the wireless operation of traditionally wired network and serial devices and can handle transparent data transfer numerical computing protocol conversion data processing and even data encryption You will find it easier to build embedded systems for distributed peer to peer communication turn wired devices into wireless devices and introduce higher mobility and more intelligence to your system In this chapter we cover the various capabilities of the W315A 325A series embedded computers The following topics are covered in this chapter O Overview O Package Checklist O Product Features O Hardware Block Diagrams gt W315A gt W325A W315A 325A Introduction Overview The W315A 325A wireless embedded computers are designed around the MOXA ART ARM9 32 bit RISC processor Unlike the X86 CPU which uses a CISC design the MOXA ART ARM9 uses RISC architecture and modern semiconductor technology to provide a powerful computing engine without generating a significant amount of heat The processor also integrates UART and LAN functions to provide exceptional communication performance but without the bus bandwidth limitations associated with general ARM based communication products An onboard NOR Flash ROM and SDRA
16. ltiple serial ports allow you to connect different devices for wireless operation and the reliable and stable hardware platform lets you devote your attention to developing your applications The following topics are covered in this chapter O Appearance gt W315A gt W325A Dimensions LED Indicators Reset Button n n on 0 Real Time Clock W315A 325A Appearance W315A Wireless GSM GPRS antenna Ethernet 10 100BaseTx 12 to 48 VDC yp Serial MOXA console port 213 LJ NN NP W315A JASESEEITT Read 4 GPR d 1 1 Internal SD slot for storage expansion 2 Internal SIM card slot remove cover to access Serial port 1 RS 232 422 485 W325A Wireless GSM GPRS antenna Ethernet 10 100BaseTx 12 to 48 VDC yp Serial MOXA console port SGeea LJR E NEU W325A El u t ID i uai 1 Internal SD slot for storage expansion 2 Internal SIM card slot remove cover to access Serial port 1 Serial port 2 RS 232 422 485 RS 232 422 485 2 2 Hardware Introduction W315A 325A Hardware Introduction Dimensions W315A W325A J W315A Wireless Embedded Computer ee0e0000 zm alls E lis Um M gt 26 1 02 77 3 03 88 3 46 LED Indicators LED Name LED Color LED Function Ready Green Power is on and functioning normally Power is off or a power error exists SD SD card is detected Of SD
17. onjunction with any other antenna or transmitter Safety Information To maintain compliance with the FCC s RF exposure guidelines when installing and or operating this equipment you should maintain a minimum distance of 20 cm between the transmitter and your body Use only the supplied antenna Unauthorized antennae modifications or attachments could damage the transmitter and may violate FCC regulations The device includes a GPRS module This module has been approved by FCC The FCC ID is 09EQ24PL001
18. rate The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together e Keep input wiring and output wiring separate e tis a good idea to label the wiring to all devices in the system ATTENTION Safety First Be sure to disconnect the power cord before installing and or wiring your W315A 325A Wiring Caution Calculate the maximum possible current in each power wire and common wire Observe all electrical codes dictating the maximum current allowable for each wire size If the current goes above the maximum ratings the wiring could overheat and cause serious damage to your equipment Temperature Caution Be careful when handling the unit When the unit is plugged in the internal components generate heat and consequently the outer casing may feel hot to the touch 3 2 W315A 325A Hardware Connection Description Connecting the Power The PC s power source should be provided by a UL listed class 2 or Limited Power Source LPS with external adaptor output rated at 12 to 48 VDC with minimum amperage of 1 2 A If the power is supplied properly the Ready LED will glow a solid green after a 25 to 30 second delay Grounding the Unit Grounding and wire routing help limit the effects of noise due to electromagnetic interference EMI Before connecting devices run a ground wire from the ground screw to the grounding surface ATTENTION This product should be mounted to a w
19. st accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment to an outlet on a circuit different from that to which the receiver is connected e Consult with the dealer or an experienced radio TV technician CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment W315A 325A Regulatory Approval Statement Prohibition of co location This device and its antenna s must not be co located or operating in c
Download Pdf Manuals
Related Search