User Instruction Manual
Contents
1. BURC Electric Catering Urn 110V Please read and keep these instructions These instructions cover the Burco 10 20 and 30 litre 110V electric catering urns SKU s 444449556 444449557 amp 444449558 C10STHF C20STHF C30STHF 444449556 444449557 444449558 Glen Dimplex Professional Appliances Stoney Lane Prescot Merseyside L35 2XW Tel 0844 815 3755 www burco co uk INTRODUCTION To ensure you obtain full benefits from your new catering urn e Please read this instruction booklet carefully and follow all instructions e Ifyou are unsure of any aspect of the installation use or performance of your appliance please contact the after sales number shown on the back page SPECIFICATIONS Mode 2 _ CtO0STHE_ C20STHF_ C30sTHF SKU Number 444449556 444449557 444449558 Diameter 305mm__ 390mm 390mm Water volume Olite t65litte 12551 3 4 B 2 51 Weight ig 4kg 5kg Voltage o ht ge 110V 50 60Hz Power rating 1500W INSTALLATION Installation Requirements It is essential that this appliance is installed correctly Installation should comply with all local electrical and health and safety requirements At end of unit life dispose of appliance and any replacement parts in a safe manner via a licenced waste handler Units are designed to be dismantled easily and recycling of all material is encouraged whenever practicable Before Connection to Power Supply2. Remove all packaging Check the appliance for damage Report any damage immediately to the carrier or supplier Remove any protective plastic coating Any water in the urn is due to testing and is normal Check the available power supply corresponds to that shown on the appliance rating label Location This catering urn is for indoor use only Allow at least 100mm clearance from any wall Only use on a flat level surface that is adequate to support the weight when full of water Do not lift or move the urn when it contains hot water or when the mains lead is plugged in The appliance is only to be installed in locations where its use and maintenance is restricted to trained personnel The mains lead should reach from the mains socket without straining the connections Do not let the mains lead hang over the edge of the table or counter and keep it away from any hot surfaces Do not let the mains lead run across an open space Do not place the appliance where the mains lead could fall into a sink Do not place the appliance near a hot gas or electric burner Electrical Connection Fitting a plug The mains lead of this appliance will already be fitted with a BS1363 13A plug If the fuse has to be replaced use a 13 amp fuse complying with BS 1362 If the plug is not suitable for your socket then the plug must be cut off and disposed of safely An appropriate plug should be fitted as follows IMPORTANT The wires in the mains lea
3. allow the urn to cool down drain out any water then press the red reset button situated under the base Cleaning ALWAYS TURN OFF THE POWER SUPPLY AND REMOVE THE PLUG BEFORE CLEANING ALLOW THE URN TO COOL THIS URN IS NOT WATERPROOF DO NOT USE A WATER JET SPRAY TO CLEAN THE INTERIOR OR EXTERIOR OF THE APPLIANCE OR USE A WATER JET IN THE VICINITY OF THE APPLIANCE Exterior Clean with water and detergent Do not use harsh abrasive cleaners as this could damage the surface finish Interior Brush any scale or sediment from the element and rinse thoroughly with clean water Descaling In hard water areas scale will form on the element and interior This will adversely affect the operation of the urn if allowed to accumulate Descale on a regular basis using a proprietary descaler recommended for stainless steel kettles Follow the instructions provided with the descaling product Scale build up can also cause the tap to drip If this should occur turn off the power supply and remove the plug Empty the urn and allow it to cool Unscrew the top of the tap from the body Wipe scrape and break the scale away from the rubber flexible seal and from the sealing surfaces inside the plastic body of the top Reassemble tightening the top of the tap until the white dot is towards the front Trouble shooting Check supply socket is switched on Check fuse and circuit breaker Check green power indicator is No power to the appliance The
4. FROM THE LID WHEN THE URN IS OPERATNG OR HAS JUST BEEN SWITCHED OFF TURN OFF THE POWER SUPPLY AND REMOVE THE PLUG WHEN NOT IN USE BEFORE CLEANING AND BEFORE REPLACING ANY PARTS Filling IMPORTANT always put water in the urn before switching on Lift the lid and fill the urn with the desired amount of water Do not fill above the MAX capacity mark WARNING if the urn is overfilled there is a risk that boiling water will be ejected from around the lid Underfilling may cause the thermal cut out to operate and may shorten the element life The urn is not suitable for heating liquids other than water or for heating water containing solids For tea making it is best to make the tea in another container However if it is necessary to make tea in the urn the tea leaves should be suspended clear of the urn bottom and heating element in a muslin bag If it is intended to heat items such as puddings or hams they should be suspended clear of the urn bottom and heating element Controls The green power indicator will be illuminated whenever power is connected to the urn Turn the thermostat to the desired setting Knob setting Approximate water temp 1 37 C 99 F 2 55 C 131 F 3 68 C 155 F 4 82 C 180 F 5 6 97 C 207 F THIS URN IS NOT INTENDED TO CONTINUOUSLY BOIL WATER DUE TO THE HAZARDS OF STEAM AND WATER ESCAPING FROM UNDER THE LID If it is necessary to keep the water at an exact temperature use a the
5. appliance does mien not operate illuminated Thermostat or element faulty Replace thermostat or element WIRING DIAGRAM ELECTRIC CATERING URN THERMOSTAT ELEMENT Bk LIMIT CUT OUT THERMOSTAT THERMOSTAT 97C 135C POWER INDICATOR GREEN Bk Wiring colour code Bk Black Bn Brown Bu Blue Gn Y Green Yellow Gn Y W White L N INLET SUPPLY CABLE Glen Dimplex Professional Appliances A Division of Glen Dimplex Home Appliances Stoney Lane Prescot Merseyside L35 2XW www burco co uk GLEN DIMPLEX PROFESSIONAL APPLIANCES 083184100 07 2011
6. d are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green or green and yellow The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black or blue The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red or brown Make sure that the connections are tight and that there are no loose strands of wire and no insulation trapped under the terminals Tighten the clamp in the plug making sure that it grips the outer covering of the cord If fitting a BS 1363 13A fused plug then fit a 13A fuse Tighten the plug cover securely If you are in any doubt consult a qualified electrician IMPORTANT if the supply cord is damaged it must be replaced by the manufacturer service agent or similar qualified person in order to avoid a hazard The supply cord may become warm when the appliance is in use WARNING THIS APPLIANCE MUST BE EARTHED Electrical connection 110V 50 60Hz 13 6A 1500W Before Use Fill heat and discard the water twice before general use USER GUIDE DURING USE THE URN BECOMES HOT BE CAREFUL NOT TO TOUCH HOT SURFACES WHEN OPENING THE LID OR FILLING TO AVOID BEING SCALDED KEEP HANDS AWAY FROM ANY STEAM
7. rmometer to check Stir the water before taking the temperature and when the desired temperature has been reached turn the control knob slowly to the left until a click from the thermostat is heard The thermostat will then cycle on and off to maintain the temperature Safety tap The tap is locked or unlocked by turning the tap lever so that either the closed or opened padlock symbol is lined up with the white dot at the front of the tap body There are two open positions one self holding so that the tap remains open and the other self closing so that the tap closes as soon as the lever is released To change the tap position turn the tap lever through 180 Open the tap by depressing the lever tap to the horizontal position Close the tap by returning the lever to the vertical position After use Turn the control knob to 0 and disconnect from the mains supply Water may be left in the urn when not in use for short periods but to maintain a supply of fresh water it should be emptied periodically and cleaned out WARNING only move the urn when it is disconnected and cool Protective cut out The heating element is fitted with a thermal cut out which protects the urn from damage if allowed to boil dry or switched on without water It is essential to keep the heating element free from scale to ensure correct operation of this cut out Scale can cause the cut out to operate when water is heating up normally If the cut out operates
Download Pdf Manuals
Related Search