915 Kb Manual_LWZ60
Contents
1. L i Disconnect from mains before starting In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakness of the lights due to accumulation of dust 2 Clean the fan each week 3 A detailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer 7 Classe LWZ 60 v1 0 TECHNICAL SPECIFICATIONS e 36PCS 10W RGBW high power LEDs e 50 000 hours lifespan and low power consumption e 8 bit smooth and 16 Bit precise resolution for PAN TILT movement e 5405 6307 pan and 265 tilt movement e 10 degrees to 60 degrees zoom e Scan position memory auto reposition after unexpected movement e RGBW color mixing system e LED shutter LED dimming e LED rainbow effect e Macros effect e Strobe effect with 18 flashes per second and pulse effect e General dimming and blackout for all four colors e 14 DMX channels e DIM4 technology 4096 step linearity dimmer e DMX52. LIGHTING PROFESSIONAL MOVING HEAD USER MANUAL CLASSE LUZ eo KEEP THIS MANUAL FOR FUTURE NEEDS Thank you for your patronage We are confident that our excellent products and service can satisfy you For your own safety please read this user manual carefully before installing the device In order to install operate and maintain the lighting safety and correctly We suggest that the installation and operation should be done by the verified technician and follow the instruction strictly CAUTION Keep this device away from rain and moisture CAUTION Unplug mains lead before opening the housing Every person involved with the installation operation and maintenance of this device has to be qualified follow carefully the instructions of this manual SAFETY INSTRUCTIONS Important safety warns CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental
3. 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal 4 5 DMX 512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1202 ON PIN 3 PIN 2 4 Classe LWZ 60 v1 0 DMX LED INDICATOR Solid red No dmx Fast flashing red Dmx signal receiving LCD Display Operations Enter Up Down Enter Value 001 512 DMX addre grymmare WE A Press Menu to Back Enter i YES oy NO Press Menu to Back Enter Up Down Pan Degree aaa Enter gt Press Menu to Back Enter Up Down YES Press Menu to Back Horizontal Enter Enter Up Down Press Menu to Back Enter Up DOWN Press Menu to Back ON OFF Reset Enter Slave Mode Press Menu to Back Sound OI Press Menu to Back Sound Mode Press Menu to Back Auto Mode Manual Enter Up Down ETEA Manual Mode Choose Channel Enter Enter Enter Up Down Number of Controfed All the motor reset Fat Enter Al the data change to or
4. 12 master slave and sound activated controllable or auto operation e Cable DMX and Wireless DMX control e Blue background LCD display e Input Voltage AC110 240V 50 60Hz e LED Quantities 36pcs 10W 4 in 1 RGBW LEDs e Control Signal DMX512 master slave and sound activated or auto operation e Control Channel 14 DMX Channels e Power Consumption 360W 380W max e Dimensions 350x260x350mm e Packing Dimensions 425x295x400mm Net Weight 9kgs e Gross Weight 11kgs Remark errors and omissions for every information given in this manual excepted All information is subject to change without prior notice 8 Classe LWZ 60 v1 0
5. 67 178 Green Blue from dark to bright 179 190 Blue Green from bright to dark 191 202 Blue Red from dark to bright 203 214 Red Blue from bright to dark 215 226 RGB from dark to bright 227 238 Blue Red from dark to bright at the same time 239 250 green from bright to dark 251 255 Output 100 at the same time 12 ZOOM 000 255 to be from narrow beam to wide beam 13 P T SPEED 000 255 Pan Tilt Motor Speed from fastest to slowest 14 CONTROL 000 127 No function 128 240 Auto programs 241 245 put a no function value between the front and end of the reset value 246 250 to reset once channel is held at this value for 3 seconds 251 255 put a no function value between the front and end of the reset value 6 Classe LWZ 60 v1 0 CLEANING AND MAINTENANCE The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed T4 CAUTION o gt
6. changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class I Therefore it is essential that the device be earthed The electric connection must carry out by qualified person Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord 1 Classe LWZ 60 v1 0 During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual modifications to the device are
7. hese qualifications do not attempt the installation yourself Improper installation can result in bodily injury CAUTION The electric connection must only be carried out by a qualified electrician Before mounting make sure that the installation area can hold a minimum point load of 10 times the device s weight Connect the fixture to the mains with the power plug Installation via the Omega holders a Fixed the clamp on the bracket by tighten up the M12 screw on the bracket to the 13 hole in the middle of the bracket b Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the device Tighten the quick lock fasteners fully clockwise c Install the second Omega holder Pull the safety rope through the holes on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw Please refer to the picture below 3 Classe LWZ 60 v1 0 DMX 512 control connection Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX output DMX Input DMX Output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 5 Pin XLR Socket 5 Pin XLR Socket
8. iginal Attention When you are in Wireless Reset function menu to Cancel the Wireless memory you need to push the Enter button for 5 seconds 5 Classe LWZ 60 v1 0 DMX Channels Channel Attribute Dmx Value Function 1 PAN 000 255 Pan movement from 0 to full Pan 2 PAN _ 16Bit 000 255 Fine pan movement from 0 to full step 3 TILT 000 255 Tilt movement from 0 to full tilt 4 TILT 16Bit 000 255 Fine tilt movement from 0 to full step 5 RED 000 255 Red dimmer from off to full 6 GREEN 000 255 Green dimmer from off to full 7 BLUE 000 255 Blue dimmer off to full 8 WHITE 000 255 White dimmer off to full 9 SHUTTER 000 006 No function 007 065 Slow to fast strobe 066 069 No function 070 128 Pulse strobe from slow to fast 129 132 No function 133 191 Strobe fading in from slow to fast 192 195 No function 196 255 Strobe fading out from slow to fast 10 DIMMER 000 255 Master dimming from Off to Full on 11 COLOR MACRO 000 004 No function 005 008 Static Color Red 009 012 Static color Amber 013 016 Static color yellow 017 020 Static Color Green 021 024 Static Color Cyan 025 028 Static Color Blue 029 033 Static Color Magenta 033 036 7200K 037 040 3200K 041 044 5600K 045 049 Eight color step at 9 speeds 050 094 No function 095 099 Eight color fade at 5 speeds 100 149 No function 150 154 Red Green from dark to bright 155 166 Green Red from bright to dark 1
9. not subject to warranty Keep away from children and non professionals GENERAL GUIDELINES This device is a LED lighting effect for professional use on stages in discotheques theatres etc the device was designed for indoor use only This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last page of this manual Lighting effects are not designed for permanent operation Consistent operation breaks may ensure that the device will serve you for a long time without defects Do not shake the device avoid brute force when installing or operating the device While choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust Please don t project the beam onto combustible substances The minimum distance between light output from the projector and the illuminated surface must be more than 1 meter If you use the quick lock cam in hanging up the fixture please make sure the quick lock fasteners turned in the quick lock holes correctly Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported For safety reasons please be aware that all modifications on the device are forbidden If this device will be o
10. perated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to short circuit burns electric shock lamp explosion crash etc 2 Classe LWZ 60 v1 0 INSTALLATION INSTRUCTIONS Mounting the device CAUTION A Please consider the GB7000 1 2007 GB7000 217 2008 and the other respective national norms during the installation The installation must only be carried out by a qualified person The applicable temperature for the lighting is between 10 C to 45 C Do not use the lighting under or above the temperature The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate safety rope Never stand directly below the device when mounting removing or servicing the fixture The operator has to make sure the safety relating and machine technical installations are approved by an expert before taking the device into operation for the first time These installations have to be approved by a skilled person once a year Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack t
Download Pdf Manuals
Related Search