USER INSTRUCTION MANUAL CARRERA HELMET
Contents
1. If the filter fails to turn dark immediately stop i use and contact a service provider for help Figure 3 No matter what shade the filter is set to the Adjust Fit Push In Turn Release Headgear Adjustments UV IR protection is always there You can never burn your eyes due to optical radiation Welding Helmets ANSI Protective clothing and accessories such as leather bibs attached to the welding helmet will protect the user from spatter and optical radiation indirectly entering from areas behind the helmet ACGIH American Conference of Governmental Industrial Hygienists has established a TLV TWA of 5mg m for welding fumes Welding fumes cannot be classified simply The composition and quantity of both are dependent on the alloy being welded and the process and electrodes used Care and Maintenance NOTE Replacement components must be used in accordance with these instructions Failure to use ArcOne replacement components in accordance with these instructions voids certification and warranty of this product Filters Clean your filter by using window cleaner or a mild soapy solution and a soft cloth or paper towel do not immerse in water or solution Ensure that the sensors are kept clean and unobstructed Change the cover plates frequently Welding Helmets Clean your helmet by using a mild soapy solution and a soft cloth or paper towel do not immerse in water or solution Warning Do not throw or abuse the helme2. Filter Removal Instructions Removable Filter Holder 1 Grab filter by top and bottom edge 2 Pull up on bottom edge of filter and slide out of the bottom of the filter holder Fig 6 BM Aitical Installation Warning Helmet impact rating Z87 with Thumb Screw installed Helmet rating Z87 without thumb screw For Z87 make sure Filter Holder Center Tab is secured to the Welding Helmet Centering Pin with Thumb Screw See ns Figure 7 Do not over tighten T et ye Filter Holder Boss Hy a n reams ae Centering Pin with Threaded Insert En T 3 iy a a Figure 7 Located along filter edge or back Warranty and Service Information Limited Warranty ArcOne warrants all auto darkening filters covered by this manual for two 2 years from the date of pur chase against manufacturing defects resulting from materials or workmanship Proof of purchase estab lishing the date of sale and filter serial number must be provided should a warranty claim be submitted The purchaser s only remedy under this limited warranty shall be limited to ArcOne s sole op tion to repair replace or refund not to exceed the purchase price This limited warranty is void in the case of unauthorized modification tampering and damage due to misuse abuse inadequate maintenance or improper storage This limited warranty is not transferable from the original purchaser to a secondary owner ArcOne shall in no even
3. ion for co workers should also be considered Technical Information Use Filters Warning Severe burns are possible with a damaged lens cracks pits holes etc Do not use damaged lens Optical radiation can possibly enter in from behind the helmet from other welders welding in the SENSITIVITY DELAY GRIND SHADE immediate area Figure 1 Filter Specific Features 1000FcF See Figure 1 Shade and Sensitivity are adjusted using the knobs on the back of the filter Change the Delay by quickly pressing and releas ing the Delay Grind button The red delay LED will turn on for Delay Press and release the Delay Grind button again to turn off To activate the grind mode press and hold down the Delay Grind button until the red Grind LED turns on Deactivate Grind mode by quickly pressing and releasing the Delay Grind button again Grind LED turns off 2000V Shade knob is on the outside of the hel met Sensitivity and Delay are adjusted using the Figure 3 knobs on the back of the filter See Figure 2 This model does not have Grind mode 2500V Same as 2000V with the addition of shade to the back See Figure 3 CARRERA 02 UI REV C Technical Use continued Adjust Height Snap Out Slide Snap In Welding Helmets Limitations of Use Filters ArcOne welding filters are not designed for oxy acetylene laser or very low amperage welding applications Do not weld with filter in the light state
4. t Doing so may crack the helmet shell or filter and is not covered by warranty Store in an appropriate place to prevent damage when not in use Storage Temp 14 F 131 F Welding helmets may be stored and transported in their original or similar packaging Spatter Protection Ensure the front cover plate is secure under all the tabs located inside the Carrera Welding Helmet and within the area covered by the Filter Holder SPATTER DAMAGE IS NOT COVERED BY WARRANTY All cover plates are 1mm thick 0 040 To install slide Rotate Non Polycarbonate under f ie lon top tabs then push underneath bottom tabs Figure 4 Parts Selection Guide see Filter Removal for replacing Filter and Cover Plates 03 OP 04 OP AD Filter Inside Polycarbonate Ne ee CARRERA 911 S Helmet Shell 02 HG Headgear Assembly Pa 04 OP Front Polycarbonate 4 n or Screw Figure 5
5. t be liable or responsible for any injury damage or loss resulting either directly or indirectly from the use or misuse of this product This limited warranty is exclusive and is in lieu of any other warranty implied either oral or written Please read the instruction man ual carefully to avoid certain situations which may void this limited warranty Troubleshooting or Return Authorization call 800 223 4685 or visit www arciweld safe com ArcOne 85 Independence Drive Taunton MA 02780 800 223 4685 USER INSTRUCTION MANUAL CARRERA HELMET WITH AUTO DARKENING FILTER Preparations for Use Filters Before you begin welding always inspect your filter to ensure it is not damaged WARNING never begin welding without first checking to see if the correct front protection plate is in place the filter is secured properly in the filter holder and the filter holder secured in the helmet Failure to protect the welding filter or install the filter filter holder correctly may cause damage and become a safety hazard should the UV IR protection be compromised from spatter or cracks from impact DAMAGE CAUSED BY ABUSE SUCH AS EXCESSIVE TEMPERATURES CRACKS FROM IMPACT AND PITTING FROM SPATTER CAUSED BY POOR MAINTENANCE WILL VOID WARRANTY Welding Helmets WARNING other safety precautions such as protective clothing adequate ventilation breathing protection such as a Clean Air Flow or equal fire extinguisher and protect
Download Pdf Manuals
Related Search