Owner/User Manual
Contents
1. 2014 VOXX ELECTRONICS CORP 150 Marcus Blvd Hauppauge NY 11788 128 9219B2. ADVDLX9 9 OVERHEAD LED BACKLIT LCD MONITOR WITH DVD PLAYER MNOVENT CD amp ED OWNER S MANUAL FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any change or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Radiation Exposure Statement This equipment complies with FCC radiation limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body Important Notice Installation of overhead products requires careful planning and preparation Be extremely careful when w
3. 1 Press the Power button to turn the unit on 2 Select DVD mode and insert the disc label facing upwards into the disc compartment 23 OVERHEAD DOME LIGHTS The Dome Lights integrated into the unit are controlled by a three position slide switch Sliding the switch to the ON position will turn the lights ON The OFF position will prevent the lights from turning ON with the vehicle s interior lighting The AUTO position will allow the lights to turn ON and OFF with the vehicle s interior lighting Refer to the Installation Guide for wire connections Do not leave the vehicle unattended with the dome light switch in the ON position as this could result in a discharged battery ACCESSORIES WIRELESS HEADPHONES The ADVDLX9 includes a built in infrared transmitter for use with the supplied wireless headphones The headphone volume is adjusted using the controls on each headset Any number of wireless headphones may be used but they must be used within a line of sight from the transmitter as infrared transmissions like visible light travel only in a straight line Note If the monitor is set to M2 mode the headphones supplied with this unit will not work as these headphones are single channel Only two channel wireless headphones will work with this unit when set to M2 mode The only time it is necessary to set this unit to M2 mode is if there is an RSA Rear Seat Audio installed in the vehicle or if two of these monitors are installed in one v
4. the connection of an USB memory device ADVDLX9 System The ADVDLX9 System has an option that allows the user to select from two IR transmit and receive codes M1 or M2 This feature can be used when using two ADVDLX9 sytems in the same installation or if the vehicle has RSA Rear Seat Audio that uses an A channel headset The ADVDLX9 system comes factory set to M1 When in the M1 mode the unit will respond to remote commands when M1 is selected on the remote control and will transmit audio on the A channel When in the M2 mode the unit will respond to remote commands when M2 is selected on the remote control and will transmit audio on the B channel Note Use 2 channel IR headphones set to CH B when the monitor is set to M2 mode Note M1 will appear on the screen for 4 5 seconds Selecting a Monitor Code M1 or M2 1 Power ON the unit and wait until M1 on the OSD appears M1 will appear on the screen for 4 5 seconds FMM 88 3MHz AUXIGAME FMM OFF DVD M1 M2 IRT ON IRT OFF 2 To change the monitor code press the System Menu button SYSTEM MENU FM MODULATOR OSD LANGUAGE DEF AULT DVD ON OFF TO REMAIN IN THE M1 MODE PRESS OK SCREEN MODE 8 MONITOR MODE M WARNING SETTING THE MONITOR TO THE M2 MODE WILL REQUIRE USING 2 CHANNEL HEADPHONES USE THE DOWN KEY ON THE REMOTE CONTROL TO SELECT M2 AND PRESS OK TO SET THE MONITOR TO M2 MODE 3 Use the A or Y cursor buttons to select th
5. 1 press the M1 button on the remote control If the monitor is set to M2 press the M2 button on the remote control See page 5 Disc won t play Insert a disc with the label side facing upwards Check the type of disc you put into disc tray This DVD only plays DVD audio CD and MP3 Blu ray BD discs will not play in this player Both the unit and the disc are coded by region If the regional codes don t match the disc can t be played Play starts but then stops immediately The disc is dirty Clean it The disc is damaged Try another disc Condensation has formed Allow player to dry out No sound or distorted sound Make sure the DVD is connected properly Make sure all cables are securely inserted into the appropriate jacks If the 2 channel IR headphones are being used turn on the IR headphone power and make sure the correct channel A B is selected Make sure the FM Modulator is ON and the proper Frequency has been selected Make sure that unit is set to M1 when using Single Channel Headphoness Cant advance through a movie You can t advance through the opening credits and warning information that appears at the beginning of a movie because the disc is programmed to prohibit that action Not allowed at the moment The feature or action cannot be completed at this time because ils ZS Wb The disc s software restricts it The disc s software doesn t support the
6. ADJUSTMENTS The System Menu contains features and options that let the user customize the system For example the user can change the FM Modulator OSD language source default screen mode display and the monitor mode Using the System Menu 1 Press the TV button and then the SYSTEM MENU button on the remote The system menu main page will appear on the screen 2 Use the cursor buttons A or Y to select an item in the sub menu and then press OK to select 3 Press the System Menu button to exit the System Menu Note The System Menu can be controlled via Remote Control only Items selected in the menu will have a green background 12 FM MODULATOR The FM Modulator allows the user to listen to audio through the vehicle s radio ON Turns the wireless FM Modulator on if audio playback through your vehicle s radio is preferred OFF Turns the wireless FM Modulator off FM CHANNEL Allows the user to select the wireless FM Modulator frequency The unit has a 100 channel built in wireless FM Modulator The FM Modulator can be set from 88 1 to 107 9 in 0 2 MHz steps i e 88 1 88 3 88 5 88 9 90 1 etc FM MODULATOR OSD LANGUAGE DEFAULT DVD ON OFF SCREEN MODE MONITOR MODE To choose an FM frequency for audio playback through your vehicle s radio 1 Press the TV button on the remote control then press the SYSTEM MENU button to access the System Menu Press OK to access the FM Modulator settings FM MODULATOR ON O
7. AGE SETUP DVD Language for On Screen Display The Language Menu allows the user to select the language for the on screen display The user can select English French Spanish German or Italian for the OSD language Se NS Press the SETUP button on the remote to enter the Setup Menu Use the A or F cursor buttons to select the Language menu option Use the cursor button to select language submenu Use the k cursor button to select language choices Use the A or Y cursor buttons to select the desired language then press OK to confirm the setting Press the SETUP button on the remote to exit the Setup Menu 15 WARNING SETTING THE MONITOR TO THE M2 MODE WILL REQUIRE USING 2 CHANNEL HEADPHONES USE THE DOWN KEY ON THE REMOTE CONTROL TO SELECT M2 AND PRESS OK TO SET THE MONITOR TO M2 MODE TO REMAIN IN THE M1 MODE PRESS OK M1 M2 Language EI Video Subtitle Off D Rating Audio English Q Misc Language Language F French m Video Subtitle Spanish Rating Audio German Itali Q Misc sna DVD SUBTITLE SETUP The Subtitle Menu allows the user to select the language for the on screen display subtitles Press the SETUP button on the remote to enter the Setup Menu Use the A or Y cursor buttons to select the Language menu option Subtitle Use the k cursor button to select subtitle submenu Use the Y cursor button to select the subtitle optio
8. EFAULT DVD ON OFF SCREEN MODE MONITOR MODE OSD LANGUAGE ENGLISH SPANISH FRENCH GERMAN DEFAULT DVD ON OFF 16 9 MONITOR MODE I 2 This allows the user to set the system monitor code M1 M2 SYSTEM MENU Press the System Menu button FM MODULATOR Use the A or Y cursor buttons to highlight MONITOR MODE and press OSD LANGUAGE OK to access the monitor mode submenu DEF AULT DVD ON OFF Use the A or Y cursor buttons to select M1 or M2 SCREEN MODE gt A MONITOR MODE Press the M2 button on the remote control after selecting M2 Press OK to confirm the setting DVD SETUP MENU SETTINGS AND ADJUSTMENTS The DVD Setup Menu contains features and options that let the user customize the DVD player For example the user can set a language for the on screen display or prevent children from viewing DVD playback of adult DVD Titles Using the Setup Menu Press the DVD button and then the SETUP button on the remote The Setup Menu appears on the screen as shown 1 Use the A or Y cursor buttons to highlight the settings to be changed Use the cursor button to highlight the sub setttings Use the cursor button to open the submenu that contains the different options available Press OK to set the desired option 2 Use the cursor button to position the highlight back on the icon side of the setup page to set the other options Repeat steps 1 2 3 Press the SETUP button again to exit the Setup Menu LANGU
9. FF FM CHANNEL 88 1MHz 88 3MHz 88 5MHz 88 7MHz 88 9MHz 89 1MHz 89 3MHz 89 5MHz 89 7MHz 89 9MHz 90 1MHz 90 3MHz 90 5MHz 90 7MHz 90 9MHz 91 1MHz 91 3MHz 91 5MHz 91 7MHz 91 9MHz 92 1MHz 92 3MHz gt 2 Use the cursor button to select FM CHANNEL then press OK The FM CHANNEL screen will appear 3 Usethe A W lt or P cursor buttons to select a frequency not used by a radio station in the area Press OK to select the highlighted frequency There are a total of 5 FM CHANNEL pages containing frequencies from 88 1 to 107 9 in 0 2 MHz steps To access the additional FM Channel pages use the A Y 4 or P cursor buttons to highlight the on screen left and right arrows and press OK Once you have selected a frequency tune your vehicle s radio to the selected frequency 4 Press the System Menu button to restore control of the DVD functions Note The wireless FM modulator will perform well in most applications However in certain applications the quality of the wireless signal may be less than optimal resulting in static or strong local station bleed through 13 OSD LANGUAGE This function allows the user to select the on screen display language The user can select English Spanish French or German for the OSD language 1 Press the System Menu button 2 Use the A or Y cursor buttons to highlight OSD LANGUAGE and press OK to access the OSD submenu 3 Use the A or Y cursor buttons to select the languag
10. NT OF THE COMPANY S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANY S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT This Warranty is in lieu of all other express warranties or liabilities ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITH IN A PERIOD NOT EXCEEDING 12 MONTHS AFTER EXPIRATION OF THE WARRANTY IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state to state VOXX Electronics Corporation 150 Marcus Blvd Hauppauge New York 11788 1 800 645 4994 G 128 9328 28 NOTES 29 For Customer Service Visit Our Website At Z www adventproducts com lt Z Product Information Photos FAQ s Owner s Manuals
11. Safety Precaution For safety reasons when changing video media it is recommended that the vehicle is not in motion and that you do not allow children to unfasten seat belts to change video media or make any adjustments to the system System adjustments can be accomplished using the remote control while seat belts remain fastened Enjoy your ADVENT entertainment system but remember the safety of all passengers remains the number one priority F EATURES 9 TFT Thin Film Transistor Active Matrix LCD Liquid Crystal Display Monitor LED Backlighting Built in DVD Player OSD On Screen Display for Control of Picture Quality and Functions Selectable M1 and M2 IR Receive and Transmit Codes See page 5 Switchable Dual Channel IR Infrared Transmitter See page 5 Four Audio Video Source Inputs DVD USB AV AUX See page 4 Dome Lights with Built in Three Way Switch Built in 100 Channel Wireless FM Modulator Last Position Memory for DVD Screen Mode Selection 4 3 16 9 Full Function Remote Control Backlit Controls AV Output via RCA Jacks Plays DVD CD and MP3 Discs CONTROLS AND INDICATORS DIAGRAM FRONT VIEW N NOUR 10 11 S J 12 1 POWER Button Used to turn the system on off standby 2 Infrared Transmitter Remote Sensor Location 3 Source Select S
12. Switch Used to select one of the four sources DVD USB AV AUX Note USB source selection is only available when a USB memory device is connected to the unit 10 11 12 PLAY gt Button This button is used to start playback of a disc STOP RI Button Press the STOP button once Stops playback Pressing the PLAY button again will resume normal playback from where movie was stopped Press the STOP button twice and then press the PLAY button to start playback from the beginning of the DVD EJECT Button This button is used for ejecting disc from the disc compartment Three Position Dome Light Switch ON Turns on the dome lights OFF The dome lights will not turn on in this position AUTO Automatically switches on the dome lights in conjunction with the vehicle s interior illumination Dome Lights Provide additional interior illumination Ventilation Openings LCD Cut Off Switch Used to turn off the LCD backlight when the LCD is in the closed position LCD Panel Screen Release Press to release the screen CONTROLS AND INDICATORS DIAGRAM SIDE VIEWS SS 2 3 y 1 DVD Disc Insertion Slot For loading and removing discs Insert disc with label side facing up 2 AUXIN This jack is used to supply external audio and video inputs to the unit Note In order to connect an external A V source the 3 5mm to RCA connectors pigtail is required 3 USB INPUT Allows for
13. e 4 Press the OK to confirm the setting SOURCE DEFAULT DVD ON OFF This allows the user to set the system default source to DVD If source default is set to ON every time the unit is turned off then on the unit will power up and automatically switch the source to DVD If source default is set to OFF and the unit is turned off then on the unit will power up in the source that was last selected The user can set the system default source to DVD 1 Press the System Menu button 2 Use the A or Y cursor buttons to highlight DEFAULT DVD ON OFF and press OK to access the submenu 3 Use the A or Y cursor buttons to select ON or OFF 4 Press the OK to confirm the setting Note The unit is set to source default DVD on as the default mode of operation Selection of Source default can only be made from within the system menu SCREEN MODE SELECT This allows the user to change the screen format aspect ratio 4 3 16 9 To select the screen aspect ratio format 1 Press the System Menu button 2 Use the A or Y cursor buttons to highlight SCREEN MODE and press OK to access the screen mode submenu 3 Use the A or Y cursor buttons to select 4 3 or 16 9 4 Press the OK to confirm the setting 14 SYSTEM MENU FM MODULATOR OSD LANGUAGE DEFAULT DVD ON OFF SCREEN MODE MONITOR MODE SYSTEM MENU FM MODULATOR OSD LANGUAGE DEFAULT DVD ON OFF SCREEN MODE MONITOR MODE SYSTEM MENU FM MODULATOR OSD LANGUAGE D
14. e Monitor Mode menu option Press OK to confirm the setting 4 Usethe A or F cursor buttons to select the desired monitor mode then press OK to confirm the setting 5 Press the M2 button on the remote 6 Press the System Menu button on the remote to exit REMOTE CONTROL OPERATION Initial Use When purchased the remote control has a battery installed with a Pull Tab to prevent battery discharge Remove the Pull Tab before attempting to use the remote control Zeg Battery Replacement 1 Remove the battery holder 2 Insert one CR2025 battery into the battery holder Be sure to observe the correct polarity 3 Align the battery holder with the remote control and insert Push it in until the holder clicks OO NO O1 BOY REMOTE CONTROL FUNCTIONS z 3 a N D Q 3 H 4 99 SS g lt a 5 m 8 s 3 5 D 0 O OE A Ka Function control is available on the unit and the Remote Control Function not available in this model POWER Press this button to turn the unit ON and OFF SOURCE Each time the button is pressed the unit will cycle through modes DVD USB AV AUX MONITOR SELECT M1 Button Set the remote control code to allow control of the unit in M1 mode M2 Button Set the remote control code to allow control of the unit in M2 mode SCAN BACKWARD 44 Press to search in a backward direction Press repeatedly to change the search sp
15. e compiled Press OK A check mark appears to the left of the selected song To add the selected songs to the program move cursor to the Add to program function and press OK The selected songs are added into a new program list and the check mark will disappear on the playlist Move the cursor to the Program view function and press OK to browse the songs in the program Press the PLAY button to play the selected songs Clear program To clear the selected song files press the STOP button twice during playback mode Move the cursor to the Edit mode function and press OK After Edit mode is selected move cursor to selected songs list and select the songs which you want to delete Press OK A check mark will appear to the left of the selected song Move the cursor to clear program and press OK The selected songs will be deleted from the play list 21 00 00 01 1 12 Flat Mode Repeat Off Mode Normal N Music Playing 00 00 01 1 12 Flat Mode Repeat Off Mode Normal Y Music Playing 00 00 01 1 12 Ch a Edit mode Program view Addtoprogram Music Playing 00 00 01 1 12 x Edit mode Broser view Clear program Music Playing Album DVD Basics To get the optimum use out of the DVD Player
16. eed from 2 4 8 16 times and normal speed SCAN FORWARD gt gt Press to search in a forward direction Press repeatedly to change the search speed from 2 4 8 16 times and normal speed TV Mode Select Switches certain function keys on the remote control for monitor functions PREVIOUS Hd Press to return to the previous chapter or track NEXT gt gt I Press to skip to the next chapter or track PLAY ki Press to activate the play mode while a disc is loaded into the disc compartment 10 11 12 13 14 15 16 17 SYSTEM MENU Allows the user to access the system menu when the unit has been placed in TV mode Press the cursor buttons A V to select FM MODULATOR OSD LANGUAGE DEFAULT DVD ON OFF SCREEN MODE MONITOR MODE Note Press once to access the System Menu press twice to exit the System Menu CURSOR A V 4P Use these buttons to access menu selections on the screen DISPLAY Press to display the current disc information while the disc is playing Use the cursor buttons A Y to select the Title or Chapter For Title Chapter selection use the numeric buttons to enter the desired Title Chapter selection OK Used to implement a selected setting or menu option SETUP Allows the user to access the Setup Menu when the unit has been placed in DVD mode Use the cursor buttons A P to select options such as language video rating Misc REPEAT Allows the user to repeat a selected t
17. ehicle Press the system menu and highlight monitor mode to change the M1 mode to M2 mode or M2 mode to M1 mode SOURCE FEATURE AV An external video source video game system or other audio video devices can be connected to the AV input To access the audio video inputs inputs turn the unit on and press the S source button or the SRC button on the remote control until AV is displayed on the screen Turn the video source component on with its power button or remote control and it is now ready to play the audio and video signals from the source connected to AV AUX The AUX input may be connected to a external video source video game system or other audio video devices via AUX harness input turn the unit ON and press the S Source button or the SRC button on the remote until AUX is displayed on screen Turn the video source component on with its power button or remote control and it is now ready to play the audio and video signal from the source connected to AUX AV Out The unit provides an AV output for optional video monitor s This output will provide the AV signals that duplicate the picture audio being processed by the unit to an additional monitor or video display Please see your installer for more information 24 TROUBLESHOOTING Problem Solution IR remote is inoperative Verify that the batteries in the remote are fresh Verify that the remote sensor eye is not obstructed If the monitor is set to M
18. epeat function has four playing options Off Single Folder and All Move the cursor to the Repeat function and press OK Each time OK is pressed the unit will cycle through the available options Off Single Folder All are displayed in that order The Repeat default is Off Off Turns the repeat function off Single Repeats the song being played until STOP is pressed Folder Plays all songs in a folder repetitively All Plays all songs on the disc repetitively Mode play mode The Mode function has 4 options Normal Shuffle Random and Music Intro Move cursor to the Mode function area and press OK repeatedly until the desired mode is displayed Normal Shuffle Random Music Intro are displayed in that order The Mode function default is Normal Normal Plays all songs in folder once Shuffle Plays songs in a folder in a shuffle order Each song in the folder is played only once Random Plays songs in a folder in a random order Each song in a folder is only be played once Music Intro Plays each song in order in the folder for 10 seconds Remark The Music Intro function provides the user with a sample of each song for 10 seconds thereby making it easy to select and listen to a favorite song Add to program To add the selected songs into Browser view make sure disc playback is off Move the cursor to the Edit mode function and press OK After Edit mode is selected move cursor to songs list and select the songs which will b
19. feature for example angles The feature is not available at the moment The requested title or chapter number is out of the range 25 Problem Solution Picture is distorted The disc might be damaged try another disc It is normal for some distortion to appear during forward or reverse scan No forward or reverse scan Some discs have sections that prohibit rapid scanning or title and chapter skip If you try to skip through the warning information and credits at the beginning of a movie you won t be able to This part of the movie is often programmed to prohibit skipping through it 26 REPLACEMENT PARTS SPECIFICATIONS Remote Control 136 5326 LCD Backlighting LED AV Adapter Pigtail 112B3227 Resolution 800 RGB x 480 Pixels 1 152 000 Operation Temperature 32 131 F 0 55 C Storage Temperature 4 158 F 20 70 C Back Light Life 20 000 Hours Video Display System NTSC PAL Video Output 1 0 Vp p 75 ohms Power Source 12 VDC Dimensions LxWxH 11 0 x 9 5 x 1 7 Closed 289mm x 243mm x 44mm Closed 11 0 x 9 5 x 8 5 Open 289mm x 243mm x 215 9mm Open Specifications are subject to change without notice 27 Cees 7 OVEN VOXX ELECTRONICS CORP the Company warrants to the original retail purchaser of this product that should this product or any part thereof except game controllers under normal use and conditions be proven defective in material or workmanship within 36 month
20. ge password menu option Press OK to enter default password 3308 then press OK Press OK again and key in a new 4 digit password then press OK to confirm the setting Press the SETUP button on the remote to exit the Setup Menu NI BW NS Note The Default Password is 3308 This password is always effective even after you have selected your own password and changed it To avoid the possibility of others using the default password to set the parental level and change the password you can record this default password in another area and delete it from this manual Some discs can be limited depending on the age of users while some discs cannot 18 Load Factory This option allows the user to reset all options to factory settings L 2 3 4 5 Press the SETUP button on the remote to enter the Setup Menu Use the A or cursor buttons to select the Misc menu option Use the gt cursor button to select the load factory option then press OK to enter the submenu Use the lt or gt cursor buttons to select the load factory Yes or No then press OK to confirm the setting Press the SETUP button on the remote to exit the Setup Menu Note This function will not affect the Rating control settings Screen Saver This option allows the user to set the Screen Saver mode ON Screen saver will appear OFF Screen saver will not appear WP WN gt 6 Note The DVD player will enter Screen Saver mode if the un
21. he rear of the driver s seat where it will not be visible directly or indirectly to the operator of the motor vehicle Warnings Do not use any solvents or cleaning materials when cleaning the video monitor Do not use any abrasive cleaners they may scratch the screen Use only a lightly dampened lint free cloth to wipe the screen if it is dirty Lock the LCD screen in the fully closed position when not in use Before putting on headphones always adjust the volume setting to the lowest position Remember to leave the dome light switch in the off or auto positions when the vehicle is unattended as the dome lights if left on can drain the vehicle s battery Do not put pressure on the screen e Caution children to avoid touching or scratching the screen as it may become dirty or damaged Licensed under one or more of the following patents Patent NOS 5 775 762 5 927 784 and 6 678 892 Congratulations Congratulations on your purchase of the ADVENT ADVDLX9 DVD Player with drop down video monitor The ADVDLX9 has been designed to give you and your family many years of video entertainment in the mobile environment Please read the directions that follow to familiarize yourself with the product to ensure that you obtain the best results from your equipment Note Installation options vary see the individual owner s manuals for each component in your system to obtain a full understanding of each component s operation
22. is not available the player will play and display on the screen the original language contained in the disc 16 DVD TV DISPLAY The TV display setup allows the user to set the screen aspect ratio 4 3 This displays the wide picture with black bands on the upper and lower portions of the screen 16 9 This displays a wide picture with black bands on the upper and lower portion of the screen The bandwidth will vary depending on the aspect ratio of the disc Press the SETUP button on the remote to enter the Setup Menu Use the A or Y cursor buttons to select the Video menu option Use the gt cursor button to select TV display submenu Use the bk cursor button to select the desired TV display submenu Use the A or YW cursor buttons to select the desired aspect ratio then press OK to confirm the setting 6 Press the SETUP button on the remote to exit the Setup Menu UB NE DVD TV Type The TV Type setup allows the user to select the television standard which corresponds to your TV NTSC Select this type for NTSC TV PAL Select this type for PAL TV MULTI Select this type for multi system TV Press the SETUP button on the remote to enter the Setup Menu Use the A or Y cursor buttons to select the Video menu option Use the gt cursor button to select TV type submenu Use the A or F cursor buttons to select the TV type menu option Use the bk cursor button to select the desired TV type submenu Use the A or cursor but
23. it is inactive for approximately 2 minutes Press the SETUP button on the remote to enter the Setup Menu Use the A or cursor buttons to select the Misc menu option Use the cursor button to select the screen saver submenu Use the Y cursor button to select the screen saver option then press OK to enter the submenu Use the A or cursor buttons to select the screen saver on or off then press OK to confirm the setting Press the SETUP button on the remote to exit the Setup Menu 19 Language Load Factory Language Load Factory Load Factory Yes No Video Rating Language Load Factory Screen Saver PLAYING DVDS 1 Press the DISPLAY button on the remote control to display the status banner The banner includes title chapter angle audio subtitle and time 2 Title Selection Press the numeric 0 9 buttons to initiate a change of title selection Then press OK to implement the selection 3 Chapter Selection Press the numeric 0 9 buttons to initiate a change of chapter selection Then press OK to implement the selection PLAYING MP3 DISCS MP3 is a format for storing digital audio An audio CD quality song can be compressed into the MP3 format with very little loss of quality while taking up much less space CD R discs that have been encoded in MP3 format can be played on the DVD player The DVD player plays the songs in the order they were burned onto the di
24. itle chapter or track A B REPEAT Allows user to repeat the playback from point A to point B Press A B button On Screen Display DVD player Once Repeat A Mark the beginning of the section to repeat Set point A Twice A B Mark the end of the section to repeat Set point B 3 times AB Off Cancel the A B repeat function SUBTITLE Press to display and select the subtitle language in DVD mode Each time you press the button the subtitle language changes Note The type and number of languages for subtitles vary from disc to disc 18 19 20 21 22 23 NUMBERS Allows the user to enter the numbers 0 9 for selection of the tracks titles chapters or password setting ZOOM Press this button to enlarge the picture when playing a DVD disc Press ZOOM button DVD player Once Q1 Enlarges the picture twice the original size Twice Q2 Enlarges the picture 3 times the original size 3 times Q3 Enlarges the picture 4 times the original size 4 times Q off Picture is returned to original size AUDIO Press to display and select audio language in DVD mode Each time you press the button the language changes Note The available languages vary from disc to disc FM MODULATOR CHANNEL SELECT C The unit has a 100 channel built in wireless FM Modulator The FM Modulator can be set from 88 1 to 107 9 in 0 2 MHz steps i e 88 1 88 3 88 5 88 9 90 1 etc Each time the C button on the remote control is pressed the FM Modulat
25. layback DVD Source This button is only active when the remote control is in DVD mode Press to switch between DVD and USB DVD Mode Select Button Switches certain function keys on the remote control for DVD function EJECT 4 Press this button to eject the disc 10 TURNING THE UNIT ON OR OFF 1 Push in the Screen Release button to unlock the LCD screen The screen will drop down slightly 2 Pivot the screen downward until a comfortable viewing angle is reached The hinge friction will hold the screen in position while the system is in use 3 Press the power button on the unit or the remote control to turn the system on and off When in use the internal backlighting will illuminate the controls 4 After the unit has been turned on and is displaying a picture adjust the viewing angle by pivoting the screen to optimize the picture quality 5 Remember to turn the unit off and pivot the LCD screen to the locked position when not in use Power ON OFF Button Screen Release 11 PICTURE CONTROL SELECT When watching a program the picture quality can be adjusted to the user s preferences 1 Press the Picture PIX button on the remote control and the on screen picture adjustment displays the adjustment bar for BRIGHTNESS CONTRAST COLOR TINT for NTSC only or RESET 2 Use the Volume buttons or to adjust the selected adjustment bar for picture quality SYSTEM MENU SETTINGS AND
26. make sure this section is read completely DVD Region Code The DVD player is preset to a region code at the factory depending on where the DVD player is sold A DVD from a different region cannot be played in this unit and the unit will display WRONG REGION Region 1 USA Canada Region 2 Japan Europe South Africa Middle East Greenland Region 3 S Korea Taiwan Hong Kong Parts of South East Asia Region 4 Australia New Zealand Latin America including Mexico Region 5 Eastern Europe Russia India Africa Region 6 China 22 Types of Discs the DVD System will play The ADVDLX9 DVD system will play the following types of discs DVD disc DVD discs which contain video Audio disc Audio CDs contain musical or sound content only e MP3disc A disc that contains audio files for example a CD R with downloaded MP3 files JPEGdisc A disc that contains JPEG files Note This system is capable of playing most recordable DVD formats However due to the variety of disc manufacturers and software playback cannot be guaranteed Loading and Playing Discs Before you load a disc make sure that it is compatible with the player Insert the disc with the label facing the vehicle s headliner Note The following discs CANNOT be used with this player MiniDisc Laserdisc CD 1 CD ROM DVD ROM Super Audio CD SACD DVD Audio e Blu ray Disc Digital Copy Discs To load and play a disc
27. n Use the gt cursor button to select subtitle submenu Use the A or Y cursor buttons to select the desired subtitle language then press OK to confirm the setting 7 Press the SETUP button on the remote to exit the Setup Menu English French Spanish German Italian Chinese Japanese Thai Q Misc Au PWNS Note The subtitle selection is only available for discs that are recorded in the languages listed in the diagram If the selected language is not available the player will play and display on the screen the original language contained in the disc DVD AUDIO SETUP The Audio Menu allows the user to select the language for audio Press the SETUP button on the remote to enter the Setup Menu Use the A or Y cursor buttons to select the Language menu option Use the gt cursor button to select audio submenu Use the Y cursor button to select the audio option Use the gt cursor button to select audio submenu Use the A or Y cursor buttons to select the DVD language you desire then press OK to confirm the setting 7 Press the SETUP button on the remote to exit the Setup Menu French oO Video Rating Q Misc Spanish German Italian Chinese Japanese Thai AuUPWN gt Note The audio language selection is only available for discs that are recorded in the listed languages If the selected language
28. or frequency will increase by 0 2 MHz steps The FM Modulator menu can accessed by pressing the System Menu button on the remote control and selecting the FM Modulator menu Refer to the SYSTEM MENU SETTINGS AND ADJUSTMENTS for more details FMM ON OFF Turns the FM Modulator power on off IRT ON OFF Turns the Infrared Transmitter on or off for IR wireless headphones PIX Picture Select Each time this button is pressed the OSD picture adjustment displays the Adjustment Bar for BRIGHTNESS CONTRAST COLOR TINT For NTSC only or RESET Once the desired adjustment bar is displayed use the VOLUME VOLUME buttons to adjust the setting The display will automatically 25 26 27 28 29 30 31 32 turn off if no adjustments are made within 6 seconds VOLUME DOWN or UP Press to decrease or increase the level of the picture adjustments after the picture select button PIX is pressed Note The volume up down will not affect the wireless headphones or the FM Modulator output MUTE Press this button to mute the audio for wireless FMM and IR headphones Pressing the button again restores the audio to the previously set level DISC MENU Allows the user to access the disc s menu mode STOP W Press to stop playback Playback will resume from the point it is stopped Press twice to stop playback fully Playback will resume from the beginning of the disc PAUSE II Press to pause p
29. orking on a vehicle with side curtain air bags Do not route wires near any portion of the side curtain air bag assemblies This includes any anchor points in A B C or D pillars of the vehicle Routing wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from fully deploying which can result in personal injury to vehicle occupants If you have any questions regarding wire routing in a vehicle please contact Audiovox Technical Support at 1 800 225 6074 When connecting power and ground in a mobile video installation ensure that the ACC wire is fused at the point where it is connected to the vehicle ACC wiring Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the mobile video product An LCD panel and or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information system control rear or side observation or navigation If the LCD panel or video monitor is used for television reception video or DVD play the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in park or when the vehicle s parking brake is applied An LCD panel or video monitor used for television reception video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to t
30. s from the date of original purchase such defect s will be repaired or replaced with reconditioned product at the Company s option without charge for parts and repair labor If your new vehicle s radio CD DVD player is covered by the manufacturer s warranty for a period of 48 months as set forth in the OEM Warranty Booklet the company will extend the Advent Mobile Video product warranty for the same period of time This is not applicable to extended warranty purchases beyond the original manufacturer s warranty A game controller if supplied is similarly warranted for ninety 90 days To obtain repair or replacement within the terms of this Warranty the product is to be delivered with proof of warranty coverage e g dated bill of sale specification of defect s transportation prepaid to the Company at the address shown below This Warranty does not extend to the elimination of externally generated static or noise to correction of antenna problems to costs incurred for installation removal or reinstallation of the product or to damage to digital memory media devices gaming devices discs speakers accessories or vehicle electrical systems This Warranty does not apply to any product or part thereof which in the opinion of the Company has suffered or been damaged through alteration improper installation mishandling misuse neglect accident or by removal or defacement of the factory serial number bar code label s THE EXTE
31. sc When playback is started the elapsed time of the track that is playing will be displayed Selecting Folders and Songs When a device containing MP3 files is loaded in the player the navigation menu appears automatically 1 Use the A or Y cursor buttons to select the desired folder if present on the left side of the menu and press OK The songs in the folder will be displayed on screen 2 Use the A or Y cursor buttons to select the desired track containing the song and press OK to begin track playback Skipping Songs Use the Next BI button on the remote control to move to the next song Use the Previous Iq button to move to the previous song 00 00 01 Selecting a Play Mode 112 Gi Filter For MP3 amp JPEG only emcee 7 The Filter Mode enables or disables the display of files contained on the media based on their file extension Er The filter function applies to the following formats Audio Audio data format MP3 WMA Photo Photo data format JPEG Video Video data format MPEG I II Music Playing 00 00 01 mw Flat Mode play the entire disc This mode is always on default During the Flat Mode all the data folder with MP3 JPEG and movies will be played in sequence If the Flat Mode function is off it will only play the selected folder other folders are disabled MusiePlaying 20 Repeat play repetitively The R
32. tons to select the desired TV standard then press OK to confirm the setting 7 Press the SETUP button on the remote to exit the Setup Menu Au BU N 17 Language TVdisplay Rating Language TV type D Rating v NTSC PAL MULTI DVD RATING SETUP Parental This feature allows the user to limit the content of movie playback from G to Adult The lower the value the lenea more strict the control SES 1 G 2 PG 3 PG 13 4 R 5 NC 17 6 Adult The rating level can only be changed when the correct password is provided To change the parental control level perform the following Press the SETUP button on the remote to enter the Setup Menu Use the A or F cursor buttons to select the Rating menu option Use the gt cursor button to select parental submenu Press OK to enter default password 3308 then press OK Press OK again to select parental submenu Use the A or F cursor buttons to select the desired rating option then press OK to confirm the setting 7 Press the SETUP button on the remote to exit the Setup Menu Hr WE Change Password To change the password to a unique your own password Language Press the SETUP button on the remote to enter the Setup Menu E Video ere Use the A or cursor buttons to select the Rating menu option Use the k cursor button to select parental submenu Use the A or Y cursor buttons to select the chan
Download Pdf Manuals
Related Search