User Manual Dust collector S01
Contents
1. Intended use 6 Information about the manual 4 Installation 14 L Liability 5 M Manual contents 6 Maintenance work 20 Motor power 9 N Noise emission 10 P Packaging 12 Personal safety equipment 9 R Responsibilities of the owner operator 7 S Safety 6 Safety instructions 12 14 19 Specifications 10 Spare parts 5 20 Storage 12 21 ammer KR Felder Strafde A 6060 Hall in Tirol Tel 43 0 5223 45 0 90 Fax 43 0 5223 45 0 99 Email info felder at Internet www felder at H2. Basic extractor Length A ca 720 mm Width B ca 380 mm Height C incl Filter ca 1670 mm Weight 25 kg c Motor power 0 75 1x220 V 50 Hz L ro Connection Z 100 mm Chip bag contents 100 Volume flow max 950 Cubic meters per hour Fig 1 Total size 4 2 Operation and storage conditions Operation room temperature 10 to 40 C Storage temperature 10 to 50 C 4 4 Noise emission The specified sound emission levels do not take into con coan only be measured in the user s workshop sideration a possible tolerance range for series produc The specified sound pressure level was measured in a tion and are not considered appropriate to identify the tree field at a distance of 1m from the machine and at a critical sound level according to the Sound accident height of 1 6 m prevention regulations The critical sound level depends on the running time the use of the machine and the en viromental conditions Therefore the critical sound level Acoustic value Idle 86 2 Decibel work 99 2 Decibel Dust collector Sol Construction 5 Construction 5 1 Overview Base Collector body Handle bar Collector casters Filter bag Order no 02 1 127 Chip bag Order no 02 2 013 10 pes Hose connection 100 mm Fig 2 Overview ERE Dust collector ammer so Transport packaging and storage H 6 Transport packaging and storage 6 1 Safety instructions Warning Ri
3. Fig 3 Rolling carriage Fig 5 Collector casters Rolling carriage Turn the base plate upside down and mount the Rollers to the base plate using the socket head cap screws screws M5x8 mm and shims as shown Socket head cap screws M5x8mm Shims Nuts Base plate Assembling casters to the base plate Screw the four long casters onto the base plate using the supplied screw M8x10 mm and shims as shown Collector casters lang Screws M8x10 mm Shims Assembling casters to the dust collector Screw the two short casters with the plastic brackets and handle to the dust collector using the screws M8x25 mm and shims as shown Collector casters short Plastic brackets Handle Screws M8x25 mm Shims ammer H Dust collector Sol Setup and installation Fig 8 Connecting rolling carriage and dust collector Fig 9 Bag rod 16 Assembling casters to the Filter body Screw the two short casters with the plastic brackets to the filter body using the screws M8x45 mm shims and nuts as shown Collector casters short Plastic brackets Screws M8x45 mm O Shims Nuts Connecting dust collector and filter body 1 Apply the seal between both machine parts 2 Connect both machine parts using shims and screws M6x1 6 Filter body Dust collector Seal Screws M6x16mm Shims Connecting rolling carriage and dust collecto
4. A AN NA 5 1 5 VVOO NONE rennende eenden taerae enaties 5 1 6 on 5 1 7 D SGI JARAN NATE KN TANNA NANANG NG NAN WAR PATA AA BAN TENAN TA NA TANNA NA ET RT 5 c A 7 2 Te Ee UBE E N EN E ET E E 7 2 2 dTe aan akan baen al AA E EEE E E 4 Ze Making changes and modifications to the machine 7 2 4 Responsibilities of the owner operator aaa eaaa eaaa see nen eaaa nana eaaa eee 8 2 5 What is required of personnel 8 2 6 E E E T EE AT E E E T T ETT 8 27 orn olen ig EN 9 2 8 NANGEN ES NOZEMA a saa aaa aaa ae E a ang A Ka a E aaa bag ginau paia alena 9 Declaration of Conformity ccsscccsssscsssscccsssccsssccesscccesssccesssccessecessssccessscesessecesseecesses 10 Ta T TTT 11 4 Dimensions and GA AENG AE oneerbare nerede 11 4 2 Operation and storage Conditions assos csxe cosas vaa as en satana gano a taco sienna 11 4 3 PG ISE GNIS TTT 12 CONSU O e E E A E A N E EA NANA NAN ANAN ga 13 5 1 ONC Ce ee eee ee ee AE eee aaa 13 Transport packaging and Storage ssccsssssccsssssccssssccsssssccessscccsesscccssssceesssssceessseeceees 14 6 1 ee NS IED OMS naas baa aaa sakajeng Aa aaa dak aan BN dad aa aaa aa aan a a kaa aan aa a daa tee 14 6 2 MUSTO sanan padagang ra aana api a ace sa eee a a aa E gan aan aa etan aaa aaa a Aa ian ian 14 6 3 KOPO PECI Ol saga a gaga NE A SEA E E E E NGE E EA AAN beenen 14 6 4 GTS IG saang kan kaga E E EE anaa a aha aa a ai Kanaan aan ideni ET EE 15 6 5 Lg 15 Setup and installation sss sss se
5. of the MAK List is prohibited Attention Any use outside the machine s intended purpose shall be considered improper and is therefore not permitted All claims regarding damage resulting from improper use that are made against the ma nufacturer and its authorised representatives shall be rejected The operator shall be solely liable for any damage that results from improper use of the machine The machine may only be operated with original manuf acturer parts and accessories from hazards and avoiding mistakes so that the machine may be operated in a safe and trouble free manner It is recommended that the operator requests proof from the personnel that the contents of the manual have been read and understood 2 3 Making changes and modifications to the machine In order to minimise risks and to ensure optimal perfor mance it is strictly prohibited to alter retrofit or modify the machine in any way without the express consent of the manufacturer All the pictograms signs and labels af fixed to the machine must be kept visible readable and may not be removed Pictograms signs and labels that have become damaged or unreadable must be replaced promptly Dust collector S01 Safe ammer H 2 4 Responsibilities of the owner operator This manual must be kept in the immediate vicinity of the machine and be accessible at all times to all persons working on or with the machine The machine may only be operated i
6. safety equipment according to the instruc such as a walls or other machines tions and check that it functions properly e Keep the work area orderly and clean Components Warning Danger electric current work on electrical fittings may only be carried out by qualified per sonnel and in strict observance of the safety instructions Before assembling and installing the machine check to make sure it is complete and in good condition Warning Risk of injury an incomplete faulty or damaged machine can lead to serious physical injury or equipment damage Only assemble and install the machine if the machine and its parts are complete and intact Attention Risk of material damage Only operate the machine in ambient temperatures from 10 to 40 C If the instructions are not followed damage may occur during storage 7 2 Installation Characteristics of the installation site e Operation room temperature 10 to 40 C e Ensure that the work surface is sufficiently stable and has the proper load bearing capacity Provide sufficient light at the workstation Ensure there is sufficient clearance for or from neigh bouring workstations e Risk of injury Keep machines tools and accessories etc out of the reach of children e Vacuum hoses and electrical wires should be layed in such a way as to avoid tripping over them Dust collector Sol Setup and installation ammer H 7 3 Machine assembly
7. ally friendly way and always in ac cordance with local waste disposal regulations If applicable contract a recycling firm to dispose of the Note Help preserve the environment Packaging materials are valuable raw materials and in many cases they can be used again or expediently reprocessed or recycled Apply a coat of oil to all bare machine parts corrosi on protection When storing for a period longer than 3 months ap ply a coat of oil to all bare machine parts corrosion protection Regularly check the general condition of all parts and the packaging If necessary refresh or re apply the coat of anti corrosive agent If the machine is to be stored in a damp environment it must be sealed in airtight packaging and protected against corrosion desiccant ERR Dust collector ammer sor Setup and installation H 7 Setup and installation 7 1 Safety instructions Warning Risk of injury Improper assembly and installation can lead to serious physical injury or equip ment damage For this reason this work may only be carried out by authorised trained personnel who are familiar with how to operate the machine and in strict observance of all safety instructions e Ensure that there is sufficient space to work around and tools that are not put in their correct place or put the machine Ensure there is ample distance bet away may be the cause of accidents ween the machine and other solid constructions e Install the
8. ammer H User Manual Dust collector so Keep this manual handy and in good condition for continual reference Dok ID 501 180 001_02 e Englisch e 2007 10 15 Dust collector Sol Attention The machine must be inspected immediately on arrival If the machine was damaged during transport or if any parts are missing a written record of the problems must be submitted to the forwarding agent and a damage report compiled Be sure also to notify your supplier immediately For the safety of all personnel it is necessary to conscientiously study this manual before assembly and T operation This manual must be kept in good condition as it belongs to the machine Furthermore keep the manual at hand and in the vicinity of the machine so that it is accessible to personnel when they are using maintaining or repairing the machine HAMMER A product of the FELDER GROUP FELDER Maschinenbau KR Felder Strafde A 6060 Hall in Tirol Tel 43 0 5223 45 0 90 Fax 43 0 5223 450 99 Email info felder com Internet www felder com 18 April 2007 Dust collector SO Table of contents Table of Contents 9 eneral MENANGAN NIN A DA MEN N EN NANA ANAN NGANA NA AR KANA a ANI NAN NINA NG Na 4 1 1 US ST TT 4 1 2 latonmation T Manul meenen e GU adana E R R Ka aa nek 4 1 3 Sd naa aii aa dag a NE ag Sees SAE a BG a EN E aga Ba agan daga Eka BN EE 4 1 4 Bela O Te KTT SANA AA GA NANGEN NG TNI KERA ET NAN
9. d without the express written consent of the manufacturer Infringement of these rights may lead to a demand for compensation or other applicable claims We reserve all rights in exercising commercial protection laws Dust collector S01 General 1 3 Liability and warranty The contents and instructions in this manual were com piled in consideration of current regulations and state of the art technology as well as based on our know how and experience acquired over many years This manual must be read carefully before commencing any work on or with this machine The manufacturer shall not be liable for damage and or faults resulting from the disregard of instructions in the manual The texts and images do not necessarily represent the delivery contents The images and graphics are not depicted on a 1 1 1 5 Warranty notice The guarantee period is in accordance with natio nal guidelines Details may be found on our website www felder group com 1 6 Spare parts complete breakdown of the machine If unauthorised spare parts are installed in the machine all warranty service compensation and liability claims against the manufacturer and their contractors dealers and representatives shall be rejected ammer H scale The actual delivery contents are dependent on custom build specifications add on options or recent technical modifications and may therefore deviate from the descriptions instructions and image
10. ened to the base 6 3 Transport inspection Upon arrival inspect the shipment to ensure that it is For all defects that are not discovered upon delivery be complete and has not suffered any damage sure to report them as soon as they are recognised as If any transport damage is visible do not accept the deli damage claims must be filed within a certain period as very or accept it only with reservation Record the scope granted by law of the damage on the transport documents delivery note Initiate the complaint process Dust collector S01 Transport packaging and storage 6 4 Packaging If no agreement has been made with the supplier to take back the packaging materials help to protect the environment by reusing the materials or separating them according to type and size for recycling USS packaging materials 6 5 Storage Keep items sealed in their packaging until they are assembled installed and be sure to observe the stacking and storage symbols on the outside of the packaging Store packed items only under the following conditions Do not store outdoors Store in a dry and dust free environment Do not expose to aggressive substances Protect from direct sunlight Avoid subjecting the machine to shocks Storage temperature 10 to 50 C Maximum humidity 60 Avoid extreme temperature fluctuations condensation build up Attention Dispose of the packaging materials in an environment
11. f it is in proper working order and in safe condition Every time before the machine is switched on it must be inspected for visible defects and general condition All instructions in this manual must be strictly followed without reservation Besides the safety advice and instructions stated in this manual it is necessary to consider and observe local ac 2 5 What is required of personnel Only authorized and trained personnel may work on and with the machine Personnel must be briefed about all functions and potential dangers of the machine Spe cialist staff is a term that refers to those who due to their professional training know how experience and knowledge of relevant regulations are in a position to assess delegated tasks and recognise potential risks If the personnel lack the necessary knowledge for wor king on or with the machine they must first be trained Responsibility for working with the machine installation service maintenance overhaul must be clearly defined and strictly observed Only those persons who can be expected to carry out their work reliably may be given 2 6 Work safety Following the safety advice and instructions given in this manual can prevent bodily injury and material dama ge while working on and with the machine Failure to observe these instructions can lead to bodily injury and damage to or destruction of the machine Disregard of the safety advice and instructions given in thi
12. his manual should be handled confidentially It is desi gnated solely for those persons who work on or with the machine All descriptions texts drawings photos and other depictions are protected by copyright and other commercial laws Illegal use of the materials is punishab le by law This manual in its entirety or parts thereof may not be transferred to third parties or copied in any way or Dust collector S01 General these particular cases special attention must be paid in order to avoid accidents injury to persons or material damage This symbol marks instructions that must be followed in order to avoid harm to one s health injuries per This symbol warns of potentially dangerous situations related to electric current Not observing the safety instructions increases the risk of serious injury or death Required electrical repairs may only be carried out This symbol marks instructions which if not observed may lead to material damage functional failures This symbol marks tips and information which should be observed to ensure efficient and failure free ope entirety and fully understood This manual is an integral part of the machine and must therefore be kept in the direct vicinity of the machine and be accessible at all times If the machine is sold rented lent or otherwise transferred to another party the manual must accompany the machine form and its contents may not be used or otherwise communicate
13. n working on or with the machine the following must be strictly observed Persons with long hair who are not wearing a hairnet are not permitted to work on or with the machine It is prohibited to wear gloves while working on or with the machine All jewellery rings bracelets necklaces etc must be removed before starting work on or with the machine When working on or with the machine the following must always be worn by personnel Protective gear overalls safety goggles dust mask hairnet to contain long hair etc Sturdy tight fitting clothing tear resistant no wide sleeves Protective footwear That protects the feet from heavy falling objects and prevents sliding on slippery floors Hearing protection To protect against loss of hearing 2 8 Machine hazards The machine has undergone a hazard analysis The properly design and construction of the machine are based on the Nevertheless there are some residual risks that must be results of this analysis and correspond to state of the art considered technology The machine runs with high electrical voltage The machine is considered operationally safe when used Warning Danger electric current electrical energy can cause serious bodily injury Damaged insulation materials or defective individual components can cause a life threatening electrical shock e Before carrying out any maintenance cleaning and e Do not remove any safety devices or alter them to p
14. nd electrical equipment The motor and electrical equipment are maintenance tree Ensure that the motor can always cool sufficiently i e clean chips and dust from the cooling fins regularly Before you start to clean the machine control if the machine parts have cooled down Switch off the device and wait for the ventilator to come to a halt Hammer 9 Spare parts Dust collector SO Spare parts Fig 14 Spare parts 17 25 23 18 Nn 01T OFOD o60 h ooo ooge gt y A S Ge o WUYYOOOO OO h Sgan 21 Fig 15 Set of screws 20 Designation Dust collector Filter bag support Set of screws Ratchet strap Filter bag Ratchet strap Chip bag Base Filter body Chip bag Filter bag Seal Steering rollers Plastic brackets Filter body Plastic brackets dust collector Collector casters long Handle Collector casters short Socket head cap screw M8x45mm Socket head cap screw M8x25mm Socket head cap screw M8x16mm Socket head cap screw M8x16mm Socket head cap screw M6x16mm Shims Mb Shims M8 Socket head cap screw M5x8mm Nuts M5 Shims M5 Allen key 5mm Allen key 4mm Pcs ammer Dust collector S01 H Index 10 Index C T Copyright 4 Transport 12 Transport inspection 12 D Dangers 8 W Declaration of Conformity 9 Warranty 5 Dimensions 10 Warranty notice 5 Work safety 7 E Electrical connection 17 Explanations of the symbols 4
15. r 1 Place the dust collector to the rolling carriage 2 Connect rolling carriage and dust collector using the screws M8x16mm shims and nuts as shown Dust collector Rolling carriage Screws M6x16mm O Shims Nuts Assembling the filter bag support Insert the filter bag support into the collector holes as shown Filter bag support ammer Dust collector Sol H Setup and installation Assembling the filter bag 1 Thread the ratchet strap into the filter bag 2 Place the filter bag over the filter bag support The filter is tightened over the blower body using the ratchet strap 3 The chip bag is placed over the blower body from be low and is also tightened by using the ratchet strap Ratchet strap Filter ba H g Filter bag Chip bag Ratchet strap Chip ba H H DAY Connecting the vacuum hose Connect the vacuum hose with the hose clamp to the collector body Vacuum hose Art No 02 0 310 Hose clamp Art No 02 0 115 Fig 11 Vacuum hose 7 4 Electrical connection Attach the dust collector to a separate power supply match the power supply Operating the machine on the The electrical circuit should have a 16 A fuse wrong voltage will damage the motor Before connecting the dust collector to the power source ensure that the On Off switch is in OFF position Check that the voltage requirements on the rating plate Attention To protect the opera
16. s contained in the manual Should any questions arise please contact the manufacturer We reserve the right to make technical modifications to the product in order to further improve user friendliness and develop its functionality Attention Non genuine counterfeit or faulty spare parts may result in damage cause malfunction or Use only genuine spare parts supplied by the manufactu rer IS Note A list of authorised genuine spare parts can be found at the end of this operating manual 1 7 Disposal If the machine is to be disposed of separate the com ponents into the various materials groups in order to allow them to be reused or selectively disposed of The whole structure is made of steel and can therefore be dismantled without problem This material is also easy to dispose of and does not pollute the environment or jeopardise public health International environmental regulations and local disposal laws must always be complied with Attention Used electrical materials electronic components lubricants and other auxiliary substances must be treated as hazardous waste and may only be disposed of by specialised licensed firms ammer H Dust collector S01 Safe 2 Safety At the time of its development and production the machi ne was built in accordance with prevailing technological regulations and therefore conforms to industry safety standards However hazards may arise should the machine be opera
17. s manual as cident prevention regulations general safety regulations as well as current environmental stipulations that apply to the operational range of the machine The operator and designated personnel are responsible for the trouble free operation of the machine as well as for clearly establishing who is in charge of installing servicing maintaining and cleaning the machine Machi nes tools and accessories must be kept out of the reach of children permission to work on or with the machine Personnel must refrain from working in ways that could harm others the environment or the machine itself It is absolu tely forbidden for anyone who is under the influence of drugs alcohol or reaction impairing medication to work on or with the machine When appointing personnel to work on the machine it is necessary to observe all local regulations regarding age and professional status The user is also responsible for ensuring that vnauthorised persons remain at a safe distance from the machine Per sonnel are obliged to immediately report to the operator any irregularities with the machine that might compromi se safety well as the accident prevention regulations and general safety regulations applicable to the operative range of the machine shall release the manufacturer and their authorised representatives from any liability and from all compensation claims Dust collector ammer wi Safe H 2 7 Personal safety Whe
18. se ssss esse senenn eenn eenn 16 7 1 ee O T 16 FD ASTON ON kasi aa baana aa servetten petervdn nnen 16 Fes Machine assembly AA TUNAN KA NAGA A AN KANA NERANGAKEN 17 7 4 Se HT Ee eN 19 7 5 EITE Ie N ae a AK wa Nb Bada aa a a ag AE ik an na aana aa Bn 22 7 6 SWC MON ONG Ol aa ani ana Aa EE a aa a aaa E Kaga Nagan A NG ANAN a ea 18 NGNE NON GG asser R I GE IBA aaa a Na Nana aaa eaaa 20 8 1 SCSI USI OC T 19 8 2 PVCS CIN CE WORK T 19 DCS en 23 1O NGGE cso este sesso aaa a aaa naa aa a KAN da a Aa TENAN NG aa WEB AA NG NG TE I NE TE A ga Na a Sa NA aaa a daga a a aaa aaa 25 ammer H 1 General 1 1 Legend Important technical safety instructions in this manual are marked with symbols These instructions for work safety must be followed In all Warning Risk of injury or death manent impairment or death Warning Danger electric current by a trained electrical technician Attention Risk of material damage and or machine breakdown Note USS ration of the machine 1 2 Information about the manual This manual describes how to operate the machine properly and safely Be sure to follow the safety tips and instructions stated here as well as any local accident prevention regulations and general safety regulations Before beginning any work on the machine ensure that the manual in particular the chapter entitled Safety and the respective safety guidelines has been read in its 1 4 Copyright T
19. sk of injury There is a risk of injury due to falling parts while transporting loading or unloa ding the machine Attention Risk of material damage The machine can be damaged or destroyed if it is subjected to impro per handling during transport For this reason the following safety instructions must be observed e Never lift loads over a person e Do not use torn or worn ropes e Always move the machine with the utmost care and e Do not use knotted ropes or belts precaution e Ensure that ropes and belts do not lie against sharp e Only use suitable lifting accessories and hoisting edges devices that have a sufficient load carrying capacity Transport the machine as carefully as possible in or e The machine should never be lifted by its protruding der to prevent damage parts e g working table e Avoid subjecting the machine to shocks e Consider the machine s centre of gravity when trans s When transporting the machine overseas ensure that porting it minimise the risk of it tipping over the packaging is airtight and that a desiccant is ad e Take measures to prevent the machine from slipping ded to protect the metal parts against corrosion sideways e Ropes belts or other hoisting devices must be equip ped with safety hooks 6 2 Transport Attention Transport the machine according to the enclosed transport and assembly instructions Never lift the machine by its planer tables Ropes belts and chains may only be fast
20. ted by untrained personnel used improperly or em ployed for purposes other than those it was designed for The chapter entitled Safety offers an overview of all the important safety considerations necessary to optimise 2 1 Intended use The dust collector SO1 is a dust and chip collecting unit with a radial compressor and vacuums chips and dust from wood and similar materials Collecting poisonous gases vapours fluids and foam The term proper use also refers to correctly observing the operating conditions as well as the specifications and instructions in this manual 2 2 Manual contents All those appointed to work on or with the machine must have fully read and understood the manual before com mencing any work This requirement must be met even if the appointed person is familiar with the operation of such a machine or a similar one or has been trained by the manufacturer Knowledge about the contents of this manual is a prerequisite for protecting personnel safety and ensure the safe and trouble free operation of the machine Additionally in order to further minimise risks the other chapters of this manual contain specific safety instruc tions all marked with symbols Besides the various instructions there are a number of pictograms signs and labels affixed to the machine that must also be heeded These must be kept visible and legible and may not be removed etc and all other materials which form part
21. tor from electrical shocks ensure that the dust collector has been earthed Attention All operations may only be executed by an authorised electrical technician EE Dust collector ammer so Setup and installation H 7 5 Circuit diagram 0 55 Kw 50 Hz 220 240 V 3 3 A Full load Fig 12 Circuit diagram 7 6 Switching on and off The dust collector is equipped with an on off switch To turn the dust collector on open the switch cover first If the switch cover is closed the dust collector is turned off automatically Upon power failure always turn this switch off to prevent the machine restarting automatically once the power returns On and Off switch Cover Fig 13 Switching on and off Dust collector S01 Maintenance 8 Maintenance 8 1 Safety instructions e Before beginning any maintenance work on the machi ne switch it off and secure it against accidentally being switched on again e Ensure that there is sufficient space to work around the machine e Keep the work area orderly and clean Components 8 2 Maintenance work Filter The cleanliness of the filter is an important motor power efficiency factor Clean the filter every time the chip bag is changed prior to the change and at the very latest once the vacuum power efficiency drops noticeably Rap all sides of the filter bag so the collected dust and chips fall down into the chip bag To clean the d
22. ust extractor effectively switch it off prior to the cleaning process Once the filter can no longer be cleaned satisfactorily replace it Replace damaged filters immediately Chip bag Empty the collection bag at the very latest when the chips reach a level approximately 6 inches below the attach ment edge In the event of damage to the collection bag the bag must be replaced immediately The dust collector must always be switched off to change the chip bag Warning Risk of injury Warning Risk of injury improper maintenance can cause serious injury or damage For this reason this work may only be carried out by authorised trained personnel who are familiar with how to operate the machine and in strict observance of all safety instructions and tools that are not put in their correct place or put away may be the cause of accidents e Following the maintenance work re install the guards and check that they are functioning properly Warning Danger electric current work on electrical fittings may only be carried out by qualified person nel and in strict observance of the safety instructions Fan wheel Clean resin residue and chips from the impeller on a weekly basis at the latest when the vacuum power sinks or the impeller becomes imbalanced Dust collector Remove chips and dust from the dust collector on a wee kly basis Remove the filter and chip bags to gain access to the interior of the unit Motor a
23. ut repair work switch off the machine and secure it them out of commission against being accidentally switched on again e When carrying out any work on the electrical equip ment ensure that the voltage supply is completely isolated Dust collector S01 Declaration of Conformi 3 Declaration of Conformity C EG Declaration of Conformit according to Machine Guidelines 98 37 EG i d Fassung 98 79 EG Manufacturer FELDER KR Felder Strafde 1 A 6060 Hall in Tirol We hereby declare that the machine indicated below which corresponds to the design and construction of the model we put on the market conforms with the safety and health requirements as stated by the EC Product designation Dust collector Make HAMMER Model designation S01 The following EC guidelines were applied 98 37 EG Machine Guidelines 73 23 EWG Low Voltage Guidelines 93 68 EWG Electromagnetic Tolerance Guidelines The following harmonised norms were applied EN 292 1 EN 50081 2 01 92 EN 292 2 EN 50082 2 03 95 EN 60204 1 This EC Declaration of Conformity is valid only if the CE label has been affixed to the machine Modifying or altering the machine without the express written agreement of the manufacturer shall render the warran ty null and void horn Gels Hall in Tirol 07 08 2006 Johann Felder Managing Director PEN Dust collector ammer so Specifications H 4 Specifications 4 1 Dimensions and weight
Download Pdf Manuals
Related Search