MIFARE Custom Configuration User Manual
Contents
1. Engineering Card used to clear the current configuration of the reader Configuration Card used to re configure the reader once the original configuration has been cleared Test Card to check the correct operation of the reader once the configuration process has been completed Please read in full and understand the content of this manual prior to undertaking the configuration process 4 CONFIGURATION PROCEDURE You will firstly need to remove power from the reader to be configured Locate the controller to which the reader to be configured is connected Remove the connector power wire either the red or black coloured conductor from the controller to remove power Or drop the power on that controller if that is easier or indeed possible Apply power to the reader by reconnecting the wire or by switching power back on the access control unit The reader will briefly show a green LED indication followed by a series of rapid flashes of the green LED and corresponding bleeps from the sounder Within 5 seconds present the Engineering Card to the reader The green LED will flash very briefly Note if a series of bleeps is emitted from the reader then re cycle the power on the reader and present the Engineering Card once more The red and green LEDs of the reader will start to flash alternately Present the Configuration Card to the reader A short bleep will be heard from the reader The reader will reboot and a a series of ra2. User Manual MIFARE Reader Custom Card Configuration Pack To Register your Product Visit http www tdsi product registration co uk UM0027_GB Issue 1 04 08 User Manual MIFARE Reader Custom Card Configuration Pack To Register your Product Visit http www tdsi product registration co uk LIRANNANT7 MM I gt 4 naina NOTICES 1 Manufacturers Details Time and Data Systems International Ltd TDSi Unit 10 Concept Park Innovation Close Poole Dorset BH12 4QT UK E mail info tdsi co uk Web http www tdsi co uk Copyright Notice Copyright O 2008 Time and Data Systems International Ltd TDSi This document or any software supplied with it may not be used for any purpose other than that for which it is supplied nor shall any part of it be reproduced without the prior written consent of TDSi TDSi Policy Time and Data Systems International Ltd operate a policy of continuous improvement and reserves the right to change specifications colours or prices of any of its products without prior notice OVERVIEW Thank you for purchasing this custom card configuration pack from TDSi This pack allows you to configure your MIFARE Sector readers to read your chosen sector using the key that you specified when ordering this product The procedure is straightforward and can be completed in a matter of seconds This pack contains 3 cards Engineering Card used to clear the current configuration of the reader Configurati
3. at only Check that this number is correctly reported by the access control system User Manual MIFARE Reader Custom Card Configuration Pack To Register your Product Visit http www tdsi product registration co uk UM0027_GB Issue 1 04 08 User Manual MIFARE Reader Custom Card Configuration Pack To Register your Product Visit http www tdsi product registration co uk LIRANANANT7 MM l gt 4 NAIAN NOTICES 3 Manufacturers Details Time and Data Systems International Ltd TDSi Unit 10 Concept Park Innovation Close Poole Dorset BH12 4QT UK E mail info tdsi co uk Web http www tdsi co uk Copyright Notice Copyright 2008 Time and Data Systems International Ltd TDSi This document or any software supplied with it may not be used for any purpose other than that for which it is supplied nor shall any part of it be reproduced without the prior written consent of TDSi TDSi Policy Time and Data Systems International Ltd operate a policy of continuous improvement and reserves the right to change specifications colours or prices of any of its products without prior notice OVERVIEW Thank you for purchasing this custom card configuration pack from TDSi This pack allows you to configure your MIFARE Sector readers to read your chosen sector using the key that you specified when ordering this product The procedure is straightforward and can be completed in a matter of seconds This pack contains 3 cards
4. e reader once the configuration process has been completed Please read in full and understand the content of this manual prior to undertaking the configuration process 2 CONFIGURATION PROCEDURE You will firstly need to remove power from the reader to be configured Locate the controller to which the reader to be configured is connected Remove the connector power wire either the red or black coloured conductor from the controller to remove power Or drop the power on that controller if that is easier or indeed possible Apply power to the reader by reconnecting the wire or by switching power back on the access control unit The reader will briefly show a green LED indication followed by a series of rapid flashes of the green LED and corresponding bleeps from the sounder Within 5 seconds present the Engineering Card to the reader The green LED will flash very briefly Note if a series of bleeps is emitted from the reader then re cycle the power on the reader and present the Engineering Card once more The red and green LEDs of the reader will start to flash alternately Present the Configuration Card to the reader A short bleep will be heard from the reader The reader will reboot and a a series of rapid flashes of the green LED and corresponding bleeps from the sounder The reader has now been reconfigured to your specifications Present the Test Card to the reader The Test Card is encoded with the number 00000001 magnetic form
5. n reconfigured to your specifications Present the Test Card to the reader The Test Card is encoded with the number 00000001 magnetic format only Check that this number is correctly reported by the access control system NOTICES Manufacturers Details Time and Data Systems International Ltd TDSi Unit 10 Concept Park Innovation Close Poole Dorset BH12 4QT UK E mail info tdsi co uk Web http www tdsi co uk Copyright Notice Copyright O 2008 Time and Data Systems International Ltd TDSi This document or any software supplied with it may not be used for any purpose other than that for which it is supplied nor shall any part of it be reproduced without the prior written consent of TDSi TDSi Policy Time and Data Systems International Ltd operate a policy of continuous improvement and reserves the right to change specifications colours or prices of any of its products without prior notice 1 OVERVIEW Thank you for purchasing this custom card configuration pack from TDSi This pack allows you to configure your MIFARE Sector readers to read your chosen sector using the key that you specified when ordering this product The procedure is straightforward and can be completed in a matter of seconds This pack contains 3 cards Engineering Card used to clear the current configuration of the reader Configuration Card used to re configure the reader once the original configuration has been cleared Test Card to check the correct operation of th
6. ns Present the Test Card to the reader The Test Card is encoded with the number 00000001 magnetic format only Check that this number is correctly reported by the access control system
7. on Card used to re configure the reader once the original configuration has been cleared Test Card to check the correct operation of the reader once the configuration process has been completed Please read in full and understand the content of this manual prior to undertaking the configuration process 2 CONFIGURATION PROCEDURE n You will firstly need to remove power from the reader to be configured Locate the controller to which the reader to be configured is connected Remove the connector power wire either the red or black coloured conductor from the controller to remove power Or drop the power on that controller if that is easier or indeed possible Apply power to the reader by reconnecting the wire or by switching power back on the access control unit The reader will briefly show a green LED indication followed by a series of rapid flashes of the green LED and corresponding bleeps from the sounder Within 5 seconds present the Engineering Card to the reader The green LED will flash very briefly Note if a series of bleeps is emitted from the reader then re cycle the power on the reader and present the Engineering Card once more The red and green LEDs of the reader will start to flash alternately Present the Configuration Card to the reader A short bleep will be heard from the reader The reader will reboot and a a series of rapid flashes of the green LED and corresponding bleeps from the sounder The reader has now bee
8. pid flashes of the green LED and corresponding bleeps from the sounder The reader has now been reconfigured to your specifications Present the Test Card to the reader The Test Card is encoded with the number 00000001 magnetic format only Check that this number is correctly reported by the access control system NOTICES Manufacturers Details Time and Data Systems International Ltd TDSi Unit 10 Concept Park Innovation Close Poole Dorset BH12 4QT UK E mail info tdsi co uk Web http www tdsi co uk Copyright Notice Copyright O 2008 Time and Data Systems International Ltd TDSi This document or any software supplied with it may not be used for any purpose other than that for which it is supplied nor shall any part of it be reproduced without the prior written consent of TDSi TDSi Policy Time and Data Systems International Ltd operate a policy of continuous improvement and reserves the right to change specifications colours or prices of any of its products without prior notice 5 OVERVIEW Thank you for purchasing this custom card configuration pack from TDSi This pack allows you to configure your MIFARE Sector readers to read your chosen sector using the key that you specified when ordering this product The procedure is straightforward and can be completed in a matter of seconds This pack contains 3 cards Engineering Card used to clear the current configuration of the reader Configuration Card used to re configure
9. the reader once the original configuration has been cleared Test Card to check the correct operation of the reader once the configuration process has been completed Please read in full and understand the content of this manual prior to undertaking the configuration process 6 CONFIGURATION PROCEDURE You will firstly need to remove power from the reader to be configured Locate the controller to which the reader to be configured is connected Remove the connector power wire either the red or black coloured conductor from the controller to remove power Or drop the power on that controller if that is easier or indeed possible Apply power to the reader by reconnecting the wire or by switching power back on the access control unit The reader will briefly show a green LED indication followed by a series of rapid flashes of the green LED and corresponding bleeps from the sounder Within 5 seconds present the Engineering Card to the reader The green LED will flash very briefly Note if a series of bleeps is emitted from the reader then re cycle the power on the reader and present the Engineering Card once more The red and green LEDs of the reader will start to flash alternately Present the Configuration Card to the reader A short bleep will be heard from the reader The reader will reboot and a a series of rapid flashes of the green LED and corresponding bleeps from the sounder The reader has now been reconfigured to your specificatio
Download Pdf Manuals
Related Search