User Manual Max Pro - Rain Master Control Systems
Contents
1. QUIT key Make sure the controllers Rain Switch if so equipped is in the automatic watering position Place the Pro Max receiver on top of the controller with the antenna pointing straight up Do not allow the antenna to touch any metal objects or wire Connect the female end of the PM SER99 cable to the Pro Max receiver and secure with lock screws Hand tighten only Connect the other end of the cable to the remote control receptacle on the front panel of the controller it is keyed to fit only in one way The controller s display will either go blank or indicate that the remote is active The Pro Max receiver will beep to indicate that it is ready for use Note NEVER operate the Pro Max transmitter without the CORRECT antenna properly installed Page 6 Rain Master Irrigation Systems Pro Max User s Manual Upon Receiver Connection Beep Response Description 1 Beep 1 2 sec Ready Multi Pro Max receiver mode 2 Beeps e Requires corresponding access code to enable Pro Max receiver operation Failed internal diagnostic tests Contact Rain 3 Beeps Master Figure 3 Pro Max Receiver to Rain Master Controller 2 1 2 Disconnecting the Receiver from a Rain Master Controller To disconnect the Pro Max Pro Max receiver follow the procedure below Step 1 Disconnect the Pro Max receiver s plug from the controller s front panel by grasping the plug housing not the c2. Rapid beeps when Pro Replace battery Rapid beeps indicate low Max transmitter key is battery condition pressed Key presses beep atthe e Check installation and antenna Pro Max transmitter but connections no valves turn ON at e Remove PM SER99 cable from the Rain Master controller controller and then re insert e Upon re insertion of the cable listen for a Pro Max receiver tone s One tone OK approximately 1 2 second Two tones OK see Section 4 6 Access Codes Any other tones contact factory e Press the AUTO UP key and listen for a confirmation beep at the Pro Max receiver If no beep heard contact factory The controller display should show remote station activity as AUTO UP is pressed If nothing displayed contact factory e Verify water is ON at selected stations If no water is available is a Master Valve Pump required Verify field station wiring is Correct e Confirm that the remote continues to work at maximum distance If not contact factory Receiver beeps once e The universal adapter has detected an Page 28 Rain Master Irrigation Systems Pro Max User s Manual every six seconds electrical short circuit when attempting to continuously For non turn ON a station Rain Master controller Check the valve solenoid and replace Model PROMAX UA if necessary Check the station wiring for short circuit to common check for insulation nicks and e
3. field wiring If you attempt to turn on a valve which has a wiring problem the Pro Max will sense the over current and turn that station OFF immediately The Pro Max receiver will beep every six seconds to indicate that you have attempted to operate a faulty station Other stations will operate normally Once the problem is fixed the station can be retried without having to walk back to the controller When you finish your testing and return to the controller the beeping indicates that you have a problem with one or more stations Power down and then up the Pro Max receiver this will eliminate the beeping 5 3 A Note About Solenoids A solenoid should never be turned ON without a plunger in place If this is done the solenoid may draw from 2 to 5 times its normal electrical current This will cause a rapid and dangerous heating cycle and may destroy the solenoid very quickly Depending upon the solenoid this electrical current may be enough to activate the attached controller s circuit breaker pop the fuse or damage the controller Page 27 Rain Master Irrigation Systems Pro Max User s Manual 6 0 Troubleshooting Pro Max System Troubleshooting Symptom Action No beep tone when Pro Replace Battery Max transmitter key is pressed No beep tone when Pro Remove end cap and press the Pro Max Max transmitter is transmitter reset button Ref Figure 10 Page pressed after changing 33 the battery
4. Used with Rain Master only controllers See Section 2 0 PROMAX UA Used with any manufacturers 24 volt AC controller See Section 3 0 1 1 Pro Max Features Simplicity e The industries easiest remote to use e Fits in shirt or pants pocket or can be attached using the convenient belt clip e Large dedicated feature keys allow most functions to be performed with a single key operation e Auto up and auto down station operation Flexibility e Can be used with any manufacturers 24 volt AC controller Model PROMAX UA e Independent control of the master valve and or pump e Single or multi station capabilities for testing system hydraulics e Timed station operation selectable from 1 to 60 minutes e Control up to 999 individual Pro Max receivers from a single Pro Max transmitter e Ability to turn a program ON or OFF when used with RME Sentar RME Hawk or Evolution DX2 controllers e Small and compact Pro Max receiver design facilities permanent internal controller mount e Compatibility with Rain Master RT5 RRAD remote Page 2 Rain Master Irrigation Systems Pro Max User s Manual Intelligence e Detects and provides an audible alert against field wiring short circuits Model PROMAX UA e No more tripped circuit breakers or blown fuses during installation checkout e Receiver has built in safety default to automatically turn station OFF after 60 minutes e Audible Pro Max transmitter and Pro Max receiv
5. for everyone to use Pro Max has been designed to give you years of dependable service To take full advantage of all the ways Pro Max can help you do your job more efficiently and economically please take a few minutes and read your User Manual It won t be long before your best friend in the field is Pro Max Figure 1 Pro Max FM Remote Control System Rain Master Irrigation Systems Pro Max User s Manual 1 0 Introduction The Pro Max Remote Control System is designed to save valuable time and energy which would have been spent walking back and forth between the controller and the irrigation field zone location It makes light work of system checkouts and service work providing field personnel with complete control over the irrigation controller Controllers may be operated remotely from watering zone sites allowing immediate evaluation of the irrigation configuration and performance Using the hand held battery operated Pro Max Transmitter from a remote zone location the operator may turn ON a single station or any number of stations with the push of a few simple keys An access code feature allows independent control of multiple Pro Max receivers permanently installed in up to 999 controllers In addition to the maintenance features the Pro Max system provides specialized irrigation functions which are described in Section 1 1 The Pro Max remote control system is composed of two model numbers Model No Description PROMAX
6. limited to the maximum f amperage supplied by the controller Even though the Pro Max t Page 22 Rain Master Irrigation Systems Pro Max User s Manual universal adapter is protected against over current it is possible that non Rain Master controllers may blow a fuse and or damage the controller if excessive current is drawn Caution should be exercised when using this feature Note The Add Stations only allows up to 5 stations and 1 master valve to be turned ON at the same time Attempting to turn on a sixth station will turn the previous 5 stations off The master valve will remain unaffected 4 7 1 Add Stations On Key Pressing the ON key during multiple station operation will turn off all stations except the one corresponding to the current number The remote will resume standard remote operation executing only one station at a time 4 7 2 Add Stations Auto Up and Auto Down Keys Pressing AUTO UP or AUTO DOWN during multiple station operation will advance the previously entered number station accordingly and turn off all other stations The remote will resume standard remote operations executing only one station at a time 4 7 3 Add Stations Off Key If the OFF key is pressed during multiple station operations all stations will be turned off If the OFF key is preceded by digits then only the entered station number will be turned off 4 8 Program Function The Program feature is designed to be used only with th
7. 4 Volts AC then leave one of the voltmeter leads ON the controllers COMMON and try the other lead of the meter to measure the low voltage wires ON the secondary of the controller s transformer Connect the PC cables 24 Volts AC wire to whichever terminal provides a reading of 24 Volts AC ON the meter Place the Rain switch in the OFF or Rain position Connect the 9 pin female end of the PM SER99 cable to the Pro Max receiver and the male end to the universal adapter Hand tighten the screw locks Align the large connector of the RMIS Part Number 32PC cable with the connector ON the universal adapter and plug them together Reconnect power to the controller Refer to the following table Upon Receiver Connection Beep Response Description 1 Beep 1 2 sec Ready for use Multi Pro Max receiver mode 2 Beeps e Requires corresponding access code to enable Pro Max receiver operation 3 Beeps Failed internal diagnostic tests Contact Rain Master No Beeps Check the 24 Volts AC and COMMON connections Temporary Connector Installation The RMIS Part Number 32TC Temporary Cable is wired in the exact same fashion as the Permanent Cable Connector described above except that it uses alligator clips for connection to the terminal strip within the controller so that it may be easily installed and Page 16 Rain Master Irrigation Systems Pro Max User s Manual removed Follow the connection instructions
8. FM Remote Control System User Manual RAIN MInaASTER TION S gt qu O a A Models PROMAX PROMAX UA March 2001 Document No 500055 Rev C Rain Master Irrigation Systems Pro Max User s Manual Table of Contents WO IMIFOGUCUOM eE E E ded 2 1 1 Pro Max Feat r S rice ere aaeei dua SANN BRANN AAA SNRA ARR 2 1 2 Ranges and Method of Transmission sssmrrrsssssssererrrrrrrrrnnnnnrnrrrrrrrrrnnn rr rr rr rr rr nn nr rr rna 3 1 3 Licensing Information che Shh aes et A Eel AE r rr rr rr rr RR RSS Ae a nn nn 4 2 0 Model PROMAX Remote Control System Rain Master ONIY sssssssssnnnn 5 2 1 Using the Receiver with a Rain Master Controller s ssssmsssrrssrsssseerrrrrrrrrnnnnnrrrrrrn rna nn 6 2 1 1 Connecting the Receiver to a Rain Master Controller ceeeeeeeeeeeeees 6 2 1 2 Disconnecting the Receiver from a Rain Master Controller ssssssseesrrrsssrennn nr 7 2 2 Permanent Mount Pro Max Receiver ssmmsssssssessrrrrrrrresererrrrrrrrrnnnnnnrrrrrrrrr nn nns rr rr rr ran nn 7 2 3 K ystroke Op rations ses fiesta cierto us a bea EE AEE E E 10 2 3 1 Evolution DX2 Keystroke Operations usmmerrssssssseeerrrrsssssnnennrnrrrrrrrennnrrrrr rr nr rna ann 12 3 0 Model PROMAX UA Remote Control System Universal scsssessseeeeeeeees 13 3 1 Using the Promax UA Universal Adapter with a Non Rain Master Controller 14 3 2 Installing the PROMAX UA SYSteMassssrrrsssseseeeerrrrrerrennnnrnrrrrrrrrnnnnrr
9. Master Irrigation Systems Pro Max User s Manual locations which are indoors especially basements or structures which are concrete and steel It may be possible to remotely locate an external antenna whenever poor Pro Max receiver locations exist Call Rain Master Technical support for assistance telephone 805 527 4498 Moving the Pro Max transmitter to a more favorable location or usage of optional high gain antennas on both the Pro Max transmitter and Pro Max receiver may improve operations The Pro Max system utilizes VHF FM communications and the Pro Max receiver Pro Max transmitter pair are factory encoded to insure that other services including other Rain Master remotes do not interfere or false trigger the Pro Max receiver Digital filtering further enhances operation in interference prone environments FM transmission is employed for its inherent quality and immunity to atmospheric static and electrical interference which are commonly found in AM types of equipment such as citizen s band radio garage door openers etc Usage of FM transmissions also insures that the stronger signal prevails capture ratio meaning that all received signals which are weaker than the Pro Max transmission are completely overridden Note Antennas are not just a piece of wire they are cut for a precise frequency of operation in order to ensure optimal performance When using antennas with the Pro Max system only utilize Rain Master specified part
10. R RES KRK RR RR eases 21 4 7 Add STAllONS foe a siren aes ea Bate heer eke hates eee hae eee 22 4 7 1 Add Stations On KEY wc deticcte cette itt tatceeteeitaatsc tet eit e tsetse tele 23 4 7 2 Add Stations Auto Up and Auto Down KeYS eceeeeeeeeeeeeeeeeeeeeeeeeees 23 47 3 POO StallONS OKEY aes ccd cocse cas aaeain a aaaea a aeDA TRAE AAE aaia 23 4 8 Program FUNCION oaee terae ianari AEA ANA AEA AE Ea aKa eade A n Aaina Al aa 23 4 8 1 Program Off KEY sissesssssrsrrrssssesnoenrrrrnsrrrnnennrrrrrrrrrnn nr rr rr rr rr rn nns rar rr rr RR RR nr rn nn 24 4 8 2 Program Auto Up Key mirim aa kader sander 24 4 8 3 Program Sensor SWItChes msssmmmssrrrssrresseeerrrrrrrrennnnnrrrrrrrrrnnn rr rr rr rr rr nn nr rr rr nn 24 4 9 Minutes FUNCION naani ae NANA AKAN ENE RENSA ANA i nye eine ny eta oi 24 4 10 Beeper Operation oie dee eee eee ook ce Sewage odes cena rr narr RARE RR KKR RR RR Rn nn rna 25 4 10 1 Power On Beeper Operation s ssmmeserrrssrrssserrrrrrrrrrennnnrrrrrrrrrrnn nn rr rr rr rr rn rn nn nr rr nan 25 4 10 2 Universal Adapter Over Current Detection Beeper mssesseesrrrrrsrrsserrrrrrrnnn nn 25 4 11 Transmitter Battery ReplaCeMeNt sssessssssrrrrrrrrssnrenrrrrrrrrnnnnnrrrr rr rr rr nn rn rr rr nn nn 25 Page ii Rain Master Irrigation Systems Pro Max User s Manual 5 0 Checking Out Electrical Problems s ssssssssssssssssssrsssssnsnnnnnnnnn nn nn ann nn RNA RANA RR RR RR RR NRA Rn 26 5 1 Field Wiring Shorts the Recei
11. Red Black Large 9 Green Black Large 10 Orange Black Large 11 Blue Black Large 12 Black White Large 13 Blue Red Large 14 Red Green Large 15 Orange Green Large 16 Black White Red Large 17 White Black Red Large 18 Red Black White Large 19 Green Black White Large 20 Orange Black White Large 21 Blue Black White Large 22 Black Red Green Large 23 White Red Green Large 24 Red Black Green Large 25 Black Small 26 White Small 27 Red Small 28 Green Small 29 Brown Small 30 Blue Small 31 Orange Small 32 Yellow Small Mv P Green White Large COMMON Orange Red Standard Large COMMON Red White Large 24 VAC Blue White Large Some cables may use this color scheme for common RAIN MASTE RRIGATION SYSTEMS 3910 B Royal Avenue Simi Valley California 93063 Telephone 805 527 4498 Fax 805 527 2813 www Rainmaster com Page 1
12. able and pulling straight out The controller display should now return to the automatic screen display 2 2 Permanent Mount Pro Max Receiver Pro Max Receivers may be permanently installed into any Rain Master controller Two items are required for permanent controller installation Page 7 Rain Master Irrigation Systems Pro Max User s Manual 1 Part No JACK IRC e Factory installed permanent interface e Factory programmed Pro Max receiver with a programmed access code 1 999 Access codes are required whenever one Pro Max transmitter controls multiple Pro Max Pro Max receivers 2 Part No PMRKIT e Permanently mounted Pro Max receiver e Antenna PROMAX ANT e All interconnecting cables and hardware Note Operation of a permanent mount Pro Max receiver requires usage of the ACCESS CODE feature key Refer to section 4 6 Figure 4 Permanent Mount Pro Max Receiver Page 8 Rain Master Irrigation Systems Pro Max User s Manual Figure 5 Pro Max Transmitter PM XMTR Page 9 Rain Master Irrigation Systems Pro Max User s Manual 2 3 Keystroke Operation The Pro Max keyboard layout is shown in Figure 4 Basic Operation Function Keystrokes Increment to next Station D gt Decrement to next Station DOWN Turn On Station 12 Es Turn Off Station 12 Q Turn On Master Valve Pump UME Turn Off Master Valve Pump Se Q Note Any prior operating station w
13. asedswssieusnaaervess Connectors not included Page 30 Rain Master Irrigation Systems Pro Max User s Manual 1 4 8 0 Pro Max Carrying Case Dimensions 12 V2L x 7 VW x 10 H Pro Max Series Parts List Model PROMAX PROMAX UA Accessories PMRKIT CMAD 12PC RMIS Part Number 24PC RMIS Part Number 32PC RMIS Part Number 32TC RMIS Part Number 32EX Pro Max Replacement Parts PM XMTR PM RCVR PM UADAPT PM PM ANT PM RCVR ANT PM XMTR ANT PM SER99 417 2013 PM CASE Option Description The complete remote set for Rain Master Controllers The complete remote set for Non Rain Master Controllers include universal adaptor Description Permanent mount remote Pro Max receiver includes antenna PM PM ANT cables amp hardware Chassis mount access door gives access to the permanent connectors through the wall of other manufacturers controllers 30 permanent connector cable for 12 stations and Master Valve Pump on non Rain Master controllers 30 permanent connector cable for 24 stations and Master Valve Pump on non Rain Master controllers 30 permanent connector for cable 32 stations and Master Valve Pump on non Rain Master controllers 60 temporary connector with alligator clips for up to 32 stations and Master Valve Pump on non Rain Master controllers 48 extension cable to connect to Pro Max receiver and PC or TC cables Typical use with CMAD Descripti
14. can be A Sent or take to an authorized Rain Master Distributor Call Rain Master at 805 527 4498 for nearest distributor B Sent or take to Rain Master Irrigation Systems Attn Service Dept 3910 B Royal Ave Simi Valley CA 93063 Warning This equipment has been tested and found to comply with the limits for Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense The user is cautioned that changes and modifications made to the equipment without approval of the manufacturer could void the user s authority to operate this equipment Page 34 Rain Master Irrigation Systems Pro Max User s Manual Wiring List for PROMAX UA Station Base Color 1 Stripe Color 2 Stripe Color Cable 1 Black Large 2 White Large 3 Red Large 4 Green Large 5 Orange Large 6 Blue Large 7 White Black Large 8
15. ccur This sequence will repeat until the power is cycled or the Controller Access Code times out 4 11 Transmitter Battery Replacement When the battery is low the normal beep sound which is emitted when a key is pressed will instead be an intermittent fast beep The battery should be replaced immediately The Pro Max transmitter battery is a 6 volt dual lithium battery pack GE Sanyo CR P2 Duracell DL223A Energizer EL223AP or equivalent This battery is available at most retailers including Radio Shack Home Base Home Depot or from your local Rain Master distributor Page 25 Rain Master Irrigation Systems Pro Max User s Manual Figure 11 Battery Replacement To replace the battery refer to Figure 11 and do the following steps Step 1 Remove the two screws from the Pro Max transmitter bottom end cap Pull the end cap off to expose the battery Step 2 Remove the battery from the battery compartment Step 3 The battery holder is designed with an extruded tab s in the center to prevent the battery from being installed backwards Position the new battery as shown and insert with the battery terminals facing into the Pro Max transmitter Note Be sure to push battery all the way in Step 4 With the battery contacts properly mated press the reset button located at the end of the circuit board to reset the electronics Step 5 Replace the bottom rubber end cap plate and secure it with the two screws Th
16. construction See additional exclusion below This limited warranty described above is in addition to whatever implied warranties may be granted to purchasers by law This limited warranty does not apply to product failure caused by improper installation or grounding improper handling physical abuse neglect whether accidental or malicious acts of God such as lightning and or power surges floods earthquakes hurricane tornados vandalism etc All implied warranties including the warranty of merchantability and fit for use are limited to the period s from date of purchase set forth below Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described above or to extend the duration of any warranties beyond the time period described herein The warranties described above shall be the sole and exclusive warranties granted by Rain Master Irrigation Systems Inc and shall be the sole and exclusive remedy available to the purchaser Correction of defects in the manner and period of time described herein shall constitute complete fulfillment of all liabilities and responsibilities of Rain Master to the purchaser with respect to the product and shall constitute full satisfaction of all claims whether based on contract negligence strict liability or otherwise In no event shall Rain Master be liable or in any way responsible for any damages or defects in the product whic
17. e following Rain Master products e RME Sentar e RME Hawk e Evolution DX2 Controllers The Program feature allows any program currently in the controller to be turned either on or off This allows special programs to be executed for testing evaluation and supplemental irrigation cycles Example To start Program 4 To turn Program 4 off Press Page 23 Rain Master Irrigation Systems Pro Max User s Manual Once started the program will run to completion whether or not the Pro Max receiver remains connected whether the Access Code is turned off or whether 60 minutes have elapsed 4 8 1 Program Off Key Pressing the OFF key while the program is running will turn the program off and the controller returns to the Automatic Mode of the operation Similarly when the program is completed the controller returns to the Automatic Mode of operation 4 8 2 Program Auto Up Key Pressing the AUTO UP key while the program is running will advance the program to the next station If the last station in the program is running the program will terminate 4 8 3 Program Sensor Switches The position of the Rain Switch will not affect the running of the program The program will still run if the Rain Switch is in the NO WATERING position Programs configured under the control of sensors will continue to operate as configured When a sensor detects sufficient watering the program will shut off watering 4 9 Minut
18. e is no need to enter the station number Note If the last station in a Rain Master controller is reached and Auto Up is pressed wrap around occurs station 1 turns on In a PROMAX UA model wrap around occurs after station 32 is reached Similarly pressing Auto Down will turn off the current station and turn on the next lower station number Once you find the station you want you may turn it on and off simply by pressing the ON and OFF keys There is no need to know the station number Example You come to a job site and you know it has a problem but you don t know which station has the problem Simply hook up the Pro Max receiver go out to the field and press Auto Up until you find the problem then use the ON and OFF keys Page 20 Rain Master Irrigation Systems Pro Max User s Manual 4 4 Onand Off Keys When the ON key is pressed the station previously entered will be turned on any other station that was on will be turned off The previous station may have been entered explicitly by the digit keys or implicitly by using the AUTO UP or AUTO DOWN keys When the remote is first connected and the ON key is pressed nothing happens because the previous station is undefined When Off is pressed any station that was on will be turned off 4 5 Master Valve Pump Key The Master Valve Pump may be turned on or off at anytime Its on off state is unaffected as other valves are turned on or off Therefore checkout of an elec
19. er tones verify proper Pro Max remote control operations at all times e High tech power saver circuitry means no more battery recharging required no down time e Transmitter has a single replacement lithium battery that can be purchased locally and field replaced The battery will last an entire season under normal conditions e Audible low battery alert e No fuses required Durability e Tough rugged all metal construction with shock absorbing rubber bumpers e Hard cover case for carefree transportation Reliability e Utilizes three mechanisms to insure reliable interference free communications Digital filters Factory set coding VHF FM communications 1 2 Ranges and Method of Transmission It is not possible to exactly predict the distance over which the Pro Max system will perform Several factors may affect the distance and reliability of any radio transmission e Frequency used e Transmission Power e Terrain e Antenna placement e Building Structures e Weather conditions e Onchannel interference e Atmospheric disturbances e Antenna types e Mode of operation AM FM etc Your Pro Max system has been designed to operate at distances up to one mile Under ideal open field conditions it can readily operate up to 5 miles When attempting to use Pro Max over extended distances it is important to ensure that the receiving antenna is properly located If possible avoid Pro Max receiver antenna Page 3 Rain
20. es Function The Minutes feature allows a station to be operated for a specified amount of time up to 60 minutes maximum A station must first be selected and turned on prior to using the Minutes key Example To turn on station 15 for 47 minutes Be gt on amp The station will turn on immediately after pressing the ON key and all other stations will go off The time count will start when the Minutes key has been pressed Note If a station number is not entered the currently selected station will be turned on for the specified time of 47 minutes The maximum allowable remote control operations time is 60 minutes When the selected station is on the only 3 keys that are recognized are 1 OFF Key The OFF key will turn the station the master valve or the pump off The controller will return to the Automatic Mode 2 AUTO UP The current station turns off and the next sequential station turns on The minute counter automatically re starts 3 AUTO DOWN The current station turns off and the previous sequential station turns on The minute counter automatically re starts Page 24 Rain Master Irrigation Systems Pro Max User s Manual when the station run time is complete either by the operator pressing the OFF key or the run time as elapsed the controller will return to the status of a newly connected remote e AUTO UP will turn on station 1 e AUTO DOWN will turn on the next sequential station e ADD STATIONS feat
21. for the permanent connector be very careful that the alligator clips are secure and not shorting to any metal or each other 3 4 Disconnecting the PROMAX UA from a Non Rain Master Controller To disconnect the universal adaptor use the following procedure Step 1 Disconnect the large 37 pin connector plug from the universal adaptor by grasping the plug s body not by the cable and pull straight out 3 5 Non Rain Master Controllers Lacking 24 Volts AC 24 Volts AC is required to power the Universal Adapter If 24 Volts AC is not available from the controller use a step down transformer to convert from the line voltage usually 117 or 240 Volts AC to 24 Volts AC and run the 24 Volts AC wire into the PC cable to the two wires designated for 24 Volts AC and COMMON There is no need to worry about the polarity of these two connections Additionally connect the PC cables COMMON wire to the controllers COMMON terminal Do not connect the PC cables 24 Volts AC wire to the controller ie S N Figure 8 PROMAX UA Installation to a Non Rain Master Controller 3 6 Disconnecting the PROMAX UA from a Non Rain Master Controller To disconnect the universal adaptor use the following procedure Page 17 Rain Master Irrigation Systems Pro Max User s Manual Step 1 Disconnect the large 37 pin connector plug from the universal adaptor by grasping the plug s body not by the cable and pull straight out 3 7 Non Rain Master Contr
22. h were caused by repairs or attempted repairs performed by anyone other than a Rain Master service dealer or center Nor shall Rain Master be liable or in any way responsible for an incidental or consequential economic or property damage Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you The Rain Master Pro Max series products carry a 2 year limited warranty unless otherwise specified In order to enforce the rights of this limited warranty please follow the directions as described in the following sections SERVICE Prior to sending your Pro Max system for service 1 Please refer to the troubleshooting section of the manual for possible solutions 2 Contact Rain Master Technical Support at 805 527 4498 Be sure you can describe your problem s and if possible be able to reproduce your problem s while ON the phone You will need the serial numbers of both your Pro Max transmitter and Pro Max receiver Page 33 Rain Master Irrigation Systems Pro Max User s Manual 3 If required to ship ensure the unit is properly packaged preferably in the original shipping case Include all cables and components and make sure adequate packaging material is used to protect the unit s from shipping abuse 4 Enclose a complete description of the type of problem that is occurring and be sure to include your name address and phone number where you can be reached 5 Product
23. ill turn OFF when an Auto Up Auto Down Station On Station Off key is pressed Timed Station Operation Minutes Function Keystrokes Turn On Station 1 for 5 minutes EN 5 MINUTES Increments To Next Station and Re start Timer Decrement To Next Station and Re start Timer Page 10 Rain Master Irrigation Systems Pro Max User s Manual Multiple Stations On Add Stations Function Keystrokes Turn On Multiple Stations 1 2 6 Turn Station 6 OFF 6 Station 1 2 remain Turn All Stations OFF Turn All Stations OFF and Increment the stations selected From Q Last Station When this function is used with the Rain Master RME Sentar RME Hawk or Evolution DX2 controllers the controller will automatically turn ON the appropriate Master Valve or Pump Program Operation Program Function Keystrokes Turn Program 5 On PROGRAM 5 Increment to Next Station in Program Turn Program 5 Off Page 11 Rain Master Irrigation Systems Pro Max User s Manual Using Multiple Receivers Access Code Function Keystrokes Enable Pro Max Receiver 15 Controller now accepts all remote keys ACCESS CODE Disable Pro Max Receiver 15 STL CODE Disable All Pro Max Receivers ACCESS CODE This function only works with the following Rain Mas
24. inals of controller From MV P wire of the Interface Cable Common of the Cable or Controller oe Figure 7 Relay such as Rain Master RLY1 Connect the wire for the PC Cable COMMON to the COMMON terminal of the controller Important If 24 Volts AC is not available from the controller s terminal strip see Section 3 5 and skip to Step 6 below Page 15 Rain Master Irrigation Systems Pro Max User s Manual 3 3 Step 5 Step 6 Step 7 Step 8 Step 9 Connect the wire from the PC cables 24 Volts AC to the 24 Volts AC terminal of the controller Note that the PC cable has only one wire for 24 Volts AC despite the controller having two 24 Volts AC terminals This is because the controller takes one of its 24 Volts AC terminals and connects it to the COMMON terminal and you have already attached the PC cables COMMON wire to the controllers COMMON terminal You must find which 24 Volts AC terminal on the controller is NOT electrically the same as the controllers COMMON terminal and connect the PC s 24 Volt AC wire to it Using a voltmeter power up the controller and set the voltmeter on a 30 Volts or higher AC scale Place one of the voltmeter leads ON the controllers COMMON terminal and use the other lead of the meter to read each of the 24 Volt AC terminals Connect the PC cables 24 Volt AC wire to whichever terminal gives a reading of 24 Volt AC on the meter If the controller does not have any terminals marked 2
25. is ends the battery replacement procedure The Pro Max transmitter has been designed to minimize power consumption to prolong battery life Power is only consumed for a very short duration whenever a key is depressed Due to the various use of the Pro Max transmitter it is impossible to predict exactly how long the battery will last In general you may expect a battery life of 6 to 12 months 5 0 Checking Out Electrical Problems 5 1 Field Wiring Shorts the Receiver and Rain Master Controllers If you suspect there is a short circuit in either the wiring or the solenoid of a station then it is important to understand what will occur when you transmit a signal to the controller to turn on that station Page 26 Rain Master Irrigation Systems Pro Max User s Manual Example If there is a short circuit on station 3 and you send a command to turn on Station 3 the controller will attempt to turn it on If the controller has a built in over current detector standard on the Rain Master RME Sentar RME Hawk and Evolution DX2 controllers the station will not be allowed to turn on The user should isolate repair the short circuit and try again The Pro Max system will remain fully operational 5 2 Field Wiring Shorts the Receiver and Non Rain Master Controllers The built in over current sensing capability of the Pro Max Universal Adapter protects the unit and controller transformer against damage due to short circuits in solenoids or
26. l commands Example To disable Pro Max receiver number 7 ACCESS Press Hob 7 Pro Max receiver number 7 is now disabled and will not respond to any commands The attached Rain Master controller returns to its automatic mode and operates as if the remote has been disconnected Note 1 It is possible to have more than one Pro Max receiver enabled simultaneously broadcast mode In this mode all enabled Pro Max receivers would respond to commands from the Pro Max transmitter Note 2 It is also possible to disable all enabled Pro Max receivers without using their Controller Access Code by pressing ACCESS CODE Note 3 The Pro Max receiver will automatically time out after 8 hours if a Pro Max receiver is left enabled and no remote activity has occurred The controller shall then resume its normal operation return to automatic mode 4 7 Add Stations The Add Stations feature allows additional stations to be added to the current operating station group Simultaneous station operation is important for testing system hydraulics and operation of multi station irrigation systems Example To add a station Station number 1 will operate in addition to any current station which may be in operation If no station is currently in operation then station 1 will be the only station on Example To turn the added stations off Additional stations may be added in the same manner Warning The use of the Add Stations feature is
27. nal strip The field wiring should remain connected and in place Simply add the RMIS Part Number 32PC wiring to it Make sure to follow the station color code wiring list illustrated ON the back cover of this manual Note The chart defines the connections for the following cables RMIS Part Number 32PC supplied with PROMAX UA RMIS Part Number 24PC 12PC and RMIS Part Number 32TC Make sure that any unused station wires on the PC cables are insulated and will not short to any metal object If there is a Master Valve and or Pump in the system make sure you understand how they are controlled before hooking up the Master Valve and or Pump wire of the Permanent Connector If there is any doubt find out before connecting it voltages above the normal 24Volts AC will damage the Pro Max Pro Max receiver unit If the Controller Supplies 24 Volts AC to activate the Master Valve Pump then connect the Master Valve Pump wire of the Permanent Connector to the controller s Master Valve Pump terminal If the Controller acts as a switch to activate the Master Valve Pump Finding two terminals in the controller associated with the Master Valve Pump usually but not always indicates that a relay will be required The relay is wired such that its coil terminals are activated by the Master Valve Pump and COMMON of the PC and its switch contacts are in parallel with the controller s two terminals see Figure 4 below To MV P Switch Type Term
28. nection cable RMIS Part Number 32PC which must be physically wired to each station of the generic controller Page 13 Rain Master Irrigation Systems Pro Max User s Manual Note If you have purchased model PROMAX UA and you need to connect to a Rain Master controller the Universal Adapter box PM UDAPT is not required Refer to section 2 0 for installation and operation In cases where the controller does not provide the required 24 Volts AC a step down transformer is employed to convert standard 117 Volts AC or 220 Volts AC to 24 Volts AC 3 1 Using the Promax UA Universal Adapter with a Non Rain Master Controller The controller serves only two purposes when using the Universal Adapter First it provides 24 Volts AC for the Pro Max receiver Never allow more than the normal 24 Volts AC up to 28 Volts AC maximum to enter the Pro Max receiver through the wires designated for 24 Volts AC If the controller runs ON a voltage other than 24 Volts AC use a step down transformer to convert the voltage to 24 Volts AC for input to the Pro Max receiver Transformers that convert higher voltages to 24 Volts AC are available from Rain Master Secondly the controller serves as a point of connection for the field wires and the Pro Max receiver s output Usually the point of connection is the terminal strip or a quick disconnect within the controller or pedestal Rain Master offers several types of connector cables for wiring to the co
29. nia No 197 50 Piso Mexico D F 06700 2 0 Model PROMAX Remote Control System Rain Master Only The PROMAX Pro Max receiver is designed to connect directly to any Rain Master controller by plugging the 9 pin connector from the Pro Max receiver into the front panel remote control jack found ON Rain Master controllers Figure 2 Complete PROMAX System Page 5 Rain Master Irrigation Systems Pro Max User s Manual PROMAX Parts List Part No Ref Description PM XMTR 1 Pro Max Remote radio transmitter PM RCVR 2 Pro Max Remote receiver PM SER99 3 36 remote cable 500055 4 Pro Max User s manual PM CASE 5 Pro Max carrying case PM ANT XMTR 6 Antenna BNC PM ANT RCVR 7 Antenna hinged BNC 2 1 Using the Receiver with a Rain Master Controller One of the unique and patented features of Rain Master Controllers is the built in capability for remote control Making the connections between the hand held remote transmitter and the Pro Max receiver which is attached to the controller takes just a few seconds 2 1 1 Connecting the Receiver to a Rain Master Controller Connecting the Pro Max receiver to the controller is a very simple operation The following procedure steps are all that is required Please refer to Figure 3 Pro Max Receiver to Rain Master Controller Step 1 Step 2 Step 3 Step 4 Make sure the controller is in the Automatic mode press the controllers
30. nrrrrnrrrrnnnr rr rr rr rr rr nn nn nr rna 9 Figure 6 Complete PROMAX UA System sssmonssrrrrssrsesseeerrrrserrnnnnnnrnrrrrrrrrnnnr rr rr rr rr rn nn nn nr rn 13 Figure 7 Relay such as Rain Master R YT sosmnsssssssssseserrrrsrsrsseerrrrrrrrrennnnrrrrrrnrrrnnn nn rr rn 15 Figure 8 PROMAX UA Installation to a Non Rain Master Controller ssssesrrrrssrrennr nn 17 Figure 9 Non Rain Master Controller 24 Volts AC msnssssssrrrssssrsssrerrrrrrrrrnnnnrrrrrnrrrnnn nn rr rn 18 Figure 10 PROMAX UA Permanent Connection sssssessrrrrrsrrrssnerrrrrrrrrrnnnnr rr rr rr rr nn narr r rna 19 Figure 11 Battery REeplaCeMONb sssssssrrrssrsrssererrrrrrrrnnnnnnrrrrrrrrrn nn r rr rr rr rr RR RR Snr rr RR RR nen nn nn 26 Notice Information furnished by Rain Master Irrigation Systems Inc is believed to be accurate and reliable However Rain Master shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material The information contained in this document is subject to change without notice Page ii Pro Max Congratulations you have chosen one of the ultimate weapons to use in keeping maintenance costs down and satisfaction high the Rain Master Pro Max Remote Control System Rain Master engineers take great pride in all their work but they are especially proud of Pro Max You ll find it packed with features you ve been looking for and it s extremely easy
31. ntroller The RMIS Part Number 32PC or RMIS Part Number 24PC Permanent Connector Cable which is intended to be permanently connected to the controller The other is the RMIS Part Number 32TC Temporary Connector using alligator clips 3 2 Installing the PROMAX UA System To install a Permanent Connector follow the instructions below Prior to installation please observe the following precautions CAREFUL CAUTION DANGER WARNING STOP PLEASE READ ALL INSTRUCTIONS AND THE FOLLOWING WARNING MESSAGES BEFORE OPERATING THIS EQUIPMENT Always use with the approved Rain Master cable connector assemblies RMIS Part Number 24PC RMIS Part Number 32PC RMIS Part Number 32TC RMIS Part Number 32EX Use of any other connector will void the warranty and may damage the Pro Max remote control system NEVER allow more than the normal 24 Volts AC to enter the Universal Adapter on any of its wires If there is any question about a connection voltage check the voltages with a voltmeter NEVER operate the Pro Max transmitter without the CORRECT antenna properly installed NEVER connect the Universal Adapter to more than one controller at a time Page 14 Rain Master Irrigation Systems Pro Max User s Manual Procedure Refer to Figure 7 Step 1 Step 2 Step 3 Step 4 Remove power from the controller Connect a single wire to each station up to 32 of the RMIS Part Number 32PC wiring harness at the controller s termi
32. ollers Lacking 24 Volts AC 24 Volts AC is required to power the Universal Adapter If 24 Volts AC is not available from the controller use a step down transformer to convert from the line voltage usually 117 or 240 Volts AC to 24 Volts AC and run the 24 Volts AC wire into the PC cable to the two wires designated for 24 Volts AC and COMMON There is no need to worry about the polarity of these two connections Additionally connect the PC cables COMMON wire to the controllers COMMON terminal Do not connect the PC cables 24 Volts AC wire to the controller Non Rain Master Controller without 24 VAC COMMON COMMON on PC High Voltage Input Output of Transformer 24 VAC on PC Figure 9 Non Rain Master Controller 24 Volts AC 3 8 Permanent Wire Connections A permanent mount connector can be installed on any controller so that the PROMAX UA can be easily installed and disconnected without having to deal with wiring connections Three parts are required see Figure 9 1 RMIS Part Number 32PC or appropriate size cable 2 RMIS Part Number CMAD chassis mount adaptor 3 RMIS Part Number 32EX 48 extension cable 3 9 Keystroke Operation Page 18 Rain Master Irrigation Systems Pro Max User s Manual Refer to section 2 3 i gt N 32PC Figure 10 PROMAX UA Permanent Connection 4 0 Detailed Operation 4 1 Remote Operation When the remote Pro Max receiver is connected to a Rain Maste
33. on Pro Max remote Pro Max transmitter includes battery and antenna PM XMTR ANT Pro Max remote Pro Max receiver and antenna PM RCVR ANT Universal adapter 32 station and Master Valve Pump output control Pro Max permanent mount 16 chassis antenna Replacement antenna for Pro Max receiver right angle Replacement antenna for Pro Max transmitter 36 remote cable with a DB9 9 pin connector Receiver connection cable for Rain Master controllers with rear permanent mount interface Pro Max Remote Case Description Page 31 Rain Master Irrigation Systems Pro Max User s Manual JACK IRC Factory installed rear permanent interface RME Hawk RME Sentar amp Evolution DX2 only Includes access code e Add T to these parts for telescope high gain version Page 32 Rain Master Irrigation Systems Pro Max User s Manual Rain Master Limited Warranty Rain Master Irrigation Systems Inc warrants to the first customer purchaser that this Rain Master brand product the product when shipped in its original container will be free from defective workmanship and materials and agrees that it will at its option either repair the defect or replace the defective product or part thereof at no charge to the purchaser for parts or labor for the time period set forth below This warranty does not apply to any appearance items of the product nor to any product the exterior of which has been altered or modified in design or
34. orsor rr 1 Watt nominal Power SOUICC sssersereoreerrnr rna One 6 volt type CR P2 lithium battery 0 to 60 degrees Celsius 32 to 140 Operating Temperature Range Fahrenheit Storage Temperature 20 to 70 degrees Celsius 4 to 158 Range Fahrenheit Humidity Range 0 to 90 non condensing Bae iy iam cccatuabinienjennionsnerdeuate CR P2 Lithium 6V user replaceable Battery Life Expectancy 1 season typical DiMeNSIONS cceeeeeeeeees gL x 1 3 8 W x 5 ZH less antenna MW GIG Inre nn eet ee ta 12 oz 7 2 Pro Max Receiver Operating Frequency 154 600 MHz SEenNSitiVity ssssossosseseer ere reor in 0 4 micro volt typical Power SOUICO ssseerrererererrnr ran 22 32 Volts AC 50 60 Hz 0 to 60 degrees Celsius 32 to 140 Operating Temperature Range Fahrenheit 20 to 70 degrees Celsius 4 to 158 Storage Temperature Range Fahrenheit Humidity Range 0 to 90 non condensing DIMENSIONS nerea 6 VAL x 3 VW x 1 1 16 H Weel iilindete lees 11 oz 7 3 Pro Max Universal Adapter 22 32 Volts AC 50 60 Hz 0 to 60 degrees Celsius 32 to 140 Power SOUIC eeeeeeeeees Operating Temperature Range Fahrenheit 20 to 70 degrees Celsius 4 to 158 Storage Temperature Range Fahrenheit 0 to 90 non condensing 1 amp station 1 5 amp total 6 VAL x 3 VW x 1 1 16 H 13 oz Humidity Range Output Capability DIMENSIONS svachisiwsv
35. r controller all running programs are aborted any stations and or any master valves or pumps that are ON will be turned OFF During the time the remote is connected the controller will display the Remote message Some controllers will blank the display or display additional information When the remote is disconnected all stations and any Master Valve or Pumps which are ON will be turned OFF The only exception are programs their operation remains unaffected upon disconnection of the Pro Max receiver See section 4 8 The Pro Max Series remote commands are an extended set of the older Rain Master RT5 RR RRAD remote control The user interface for Pro Max remains identical when performing like functions The Pro Max remote control system however has several newer capabilities and features which will be delimited in subsequent sections In general turning a station ON or OFF is independent of the master valve operation That is turning a station ON will not affect the state of the master valve and vice versa The exception to this is timed station operation Turning a station ON for a certain period of time will automatically select the proper master valve and or pump as required in order to perform irrigation With the older Rain Master RT5 series remote system only one station was allowed to be on at a time All remote key operations resulted in the previous station being turned Page 19 Rain Master Irrigation Systems Pro Max U
36. r rr rr rr rr nn rn rr rr rn nn 14 3 3 Temporary Connector Installation smssmmsssssssssssssrrrrrrrrrsnnnrrrrrrrrrrnnnnnrrr rr rr rr rn nn n nr rr rna 16 3 4 Disconnecting the PROMAX UA from a Non Rain Master Controller 17 3 5 Non Rain Master Controllers Lacking 24 Volts AC missesssrrssssrssserrrrrrsrrrnnnnnrrr rna ann 17 3 6 Disconnecting the PROMAX UA from a Non Rain Master Controller 17 3 7 Non Rain Master Controllers Lacking 24 Volts AC missesssrrssssessrerrrrrrrrrrnnnnnrrr rna nn 18 3 8 Permanent Wire Connections esmosssssrrrsrrressrrrrrrrrrrrrrnnnrrr nns rr rn nn nr rr rr rr hinting rr rn nn 18 3 9 Keystroke OPEratlONasssssesseeerrrrrssressnenrrrrrrrrrrnnnrorrrrrrrrrrn nn rr rr rr rr rr desea nennen rrenen 18 4 0 Detailed Operation ssssssssssssssssssssnnnnnnnnnnnns nanna nn nn nn RNA RANA RRD RR RNA RAR RR RR RER RR ARR RR RR nn 19 4 1 Remote OPE Fat ss sevsioisusissorsierssnns nere baren dne a kee 19 42 Stallions Omand OM rsictcsceetncesciticts sid urna theses etnias A tela at ARSA ERA r 20 4 3 Auto Up and Auto Down KEYS sssrrrsssssssseerrrrssrresnnnnnrrrrrrrrrnnnrrrrrrrrrrn nn r rr rr nr rr rn nen rna 20 4 4 On and Off KEYS ssosssssrrsssrsssssesrrrresrrennnnrrrrrrrrrrnnn nr rr rr rr rr rn oa oes CR a see att 21 4 5 Master MV alve P Um pi Key erena a coceaneas os dcucctunecnuaeevecuscqctanectauinwetine 21 4 6 Controller Access COCO save es cz cues puazsuecytgsinesctesduesetavouescees ihe rr rr rr R
37. s which are available through your authorized Rain Master distributor 1 3 Licensing Information Your Rain Master Pro Max radio operates on FM radio communication frequencies and is subject to the rules and regulations of the local communications governing agencies These agencies may require that all operators using private land mobile or general mobile radio frequencies obtain a radio license before operating their equipment The operator receives a license for use of the radio equipment under a specific eligibility and ON a particular frequency or set of frequencies To determine eligibility for use of private land mobile service frequencies contact your local communications governing agency This agency can supply information required to properly obtain and complete the license application form For U S License Applications contact FCC Forms Distribution Center 1 800 418 3676 Request form 600 and all schedules and instructions For license questions call the FCC at 1 888 225 5322 The following are addresses of communications agencies in North America Page 4 Rain Master Irrigation Systems Pro Max User s Manual United States Canada Federal Communications Department of Communications Commission 1241 Clyde Avenue 1270 Fairfield Road Ottawa Ontario Gettysburg PA 17325 7245 K2C 143 1 800 322 1117 Mexico Sectretaria De Comunicaciones Y Transportes Direccion General de Politicas Y Normas de Comunicaciones Av Euge
38. ser s Manual off prior to the next station turning on This is also true with Pro Max with one exception The ADD STATIONS feature has been incorporated so that multiple stations may be turned on simultaneously Each time a key is depressed at the Pro Max transmitter a confirmation audio beep is generated Upon receipt of the command the Pro Max receiver also generates a confirmation beep Consequently basic Pro Max system performance can be verified by hitting a key at the Pro Max transmitter while listening for the corresponding beep at the Pro Max receiver 4 2 Stations On and Off When one of the Pro Max transmitter s keys is pressed a signal is transmitted and an audible tone is generated to acknowledge that the signal has been transmitted All stations except the Master Valve Pump are turned on by pressing the number of the station followed by the ON key To turn off a station simply press the OFF key To turn the station on again press the ON key There is no need to press the station s number until a new station is desired Example To turn Station 12 on then off and then on again TOOT Example To go to Station 3 there is no need to turn 12 off The controller automatically turned Station 12 off prior to turning Station 3 on 4 3 Auto Up and Auto Down Keys For convenience and the rapid checkout of a system pressing Auto Up will turn off the current station and turn on the next sequential station number Ther
39. ter controllers RME Sentar RME Hawk Evolution DX2 controllers Only one program can be operated at a time 2 3 1 Evolution DX2 Keystroke Operations The following operations are only available when using the Pro Max Remote Control System with the Rain Master Evolution DX2 Controller Evolution DX2 Master Valve Function Keystrokes Turn On Master Valve One MV PUMP Turn ON Master Valve Two V PUMP Turn On Normally Open Master Valve Closes the normally open valve Turn Off Normally Open Master Valve Valve returns to normally open state M MV PUMP MV PUMP Turn On Pump Q0 MV PUMP Page 12 Rain Master Irrigation Systems Pro Max User s Manual 3 0 Model PROMAX UA Remote Control System Universal The PROMAX UA Universal Adapter Model offers the capability to connect to virtually any controller regardless of manufacturer This system consists of Figure 6 Complete PROMAX UA System PROMAX UA Parts List Part No Ref Description PM XMTR 1 Pro Max Remote radio transmitter PM RCVR 2 Pro Max Remote receiver PM SER99 3 36 remote cable PM UADAPT 4 Universal adapter 32 PC 5 30 permanent connector 6 7 8 9 500055 Pro Max User Manual PM CASE Pro Max carrying case PM ANT XMTR Antenna BNC PM ANT RCVR Antenna hinged BNC The Universal Adapter is equipped with a 35 conductor con
40. trical problem on any valve may be accomplished without actually watering simply by turning the Master Valve Pump off This assumes the system has a Master Valve and or Pump Example To turn the Master Valve Pump on MV Press PUMP To turn it off ST MV ress PUMP Refer to section 2 3 for additional Master Valve and Pump operations which are applicable to the Evolution DX2 controller 4 6 Controller Access Code The Access Code key is used to enable disable the remote control Pro Max receiver This allows the user to have numerous Pro Max receivers permanently attached to Rain Master controllers or any manufacturer s controllers at different geographic sites each with their own Controller Access Code One transmitter can be used to address them individually Access codes are factory defined numbers ranging from 1 999 These codes are factory programmable and should be requested at the time the unit is ordered You must know the Controller Access Code of the individual Pro Max receivers The access code number of any Pro Max receiver is listed within the Pro Max receiver serial number on the Pro Max receiver label Example S N R0302001 002 007 The access code appears as the last 3 digits following the second dash in this case 007 Page 21 Rain Master Irrigation Systems Pro Max User s Manual Example To enable Pro Max receiver number 7 ACCESS Press Hob Receiver number 7 is now enabled and responds to al
41. ure will do nothing as there is no current number defined 4 10 Beeper Operation Beep tones are used to indicate the operational status of the Pro Max transmitter or Pro Max receiver A valid beep occurs when a key is pressed and the Pro Max transmitter unit acknowledges the key entry by producing a single short tone burst An invalid response occurs when a invalid key is pressed resulting in a series of short tones going on and off continuously The Pro Max receiver will emit a valid beep whenever a valid command is received from the Pro Max transmitter An invalid beep will occur whenever an illegal command sequence is received 4 10 1 Power On Beeper Operation When a Pro Max receiver is first powered on a single beep is emitted for a duration of approximately 1 2 second The single beep indicates that the Pro Max receiver is operational If the Pro Max receiver emits two beeps on power up this indicates that the Pro Max receiver is programmed for access code operation Refer to section 4 6 for details on access code operation If the Pro Max receiver emits three beeps upon power up or at any other time this indicates an invalid condition Remove power and try again If the invalid operational condition continues contact your local Rain Master distributor 4 10 2 Universal Adapter Over Current Detection Beeper If an over current condition in the Universal Adapter has been detected a beep sequence of once every six seconds will o
42. ver and Rain Master Controllers mmssmmmmmssssrrrrsrrrsnn 26 5 2 Field Wiring Shorts the Receiver and Non Rain Master Controllers 27 5 3 A Note About SolenoidS cccccccecccccccccceceeeeeeeeeeceeeeceececeeeeeeeeseeeeeeeseeseeseeseness 27 6 0 Troubleshooting issssssiiieinisesaun unanini aaniu ariassan nararansan aiia inakaa 28 7 0 Pro Max SDCCHICAUONS weicephicthiusttutniutbietiheidtushedehiuthiathiutlbath hut bdaphiethsustuslawtlsenineadtn 30 Lod PTO Max TV Fa SIMO Bs cinch 30 TAA PEO WAX CC OIVE Mresincs tose tres a a T 30 7 3 Pro Max Universal Adapter weakened sec Nene tea fete oN rr rr rr rr hatte 30 1 4 Pro Max Carrying CaS siinsest anpa e aaa krk sger a svs b k bg Dk kt 31 8 0 Pro Max Series Parts LISt aoin eei ereed ara a araa aa araa aaa eraa ariari 31 Rain Master Limited WarraNty sssesssssssssssssrsssnsnnnnnnnnnssnn nns nen nn RNA ANAR ARR RER RAA ARR RR nn nn 33 Table of Figures Figure 1 Pro Max FM Remote Control SYSteM ssssssessrrrssrrssnernrrrrrrrrrnnnrnrrrrrrrrrnnn rr rr rr nn nn 1 Figure 2 Complete PROMAX System mssrssssessseerrrrsrssesnennrrrrrrrrrnnnnnrrrrrrrrrrn nr rr rr rr rr rn nen nr nn 5 Figure 3 Pro Max Receiver to Rain Master Controller sssssssssssssseerrrrrrsrrrnnnnnrrrrnrrrnnnnnr rr nn 7 Figure 4 Permanent Mount Pro Max Receiver sssmusssssssssessrrrrrrrrssnenrrrrrrrrrnnnnnrr rr rr rr rn nn nn rna 8 Figure 5 Pro Max Transmitter PM XMTHR ssssssssssssssseeeerrrrssrennnnn
43. xposed wiring in standing water When field problem is fixed turn station back ON Cycle Pro Max receiver power to reset the unit Note The Pro Max system will continue to operate normally for non shorted stations Keys beep at Pro Max e Check installation and antenna transmitter but no valves connections see Section 3 2 Figure 8 turn on at a non Rain and Figure 9 Master controller Remove the large 37 pin connector from Model PROMAX UA ee the universal adapter assembly and then re insert e Upon re insertion of the cable listen for the Pro Max receiver tone s No tone check the 24 Volts AC and common connections One tone OK approximately 1 2 second Two tones OK see Section 4 6 Access Code Any other tones contact factory e Press the AUTO UP key and listen for a confirmation beep at the Pro Max receiver If no beep contact factory e Verify water is ON at the selected stations If no water is available is a Master Valve Pump required Verify field station wiring is correct e Confirm that the remote continues to work at maximum distance If not contact factory Page 29 Rain Master Irrigation Systems Pro Max User s Manual 7 0 Pro Max Specifications 7 1 Pro Max Transmitter Operating FrequenCYy 154 600 MHz Modulation type sssserssrsersersnea Frequency Modulation Frequency Stability 005 Power OUtpUt ssossers
Download Pdf Manuals
Related Search