Home

MTP-1530II Modular Thermal Printer User Manual

Contents

1. Print Mode Settings Print Mode Settings Bit 7 0 Underline OFF 1 Underline ON Bit 6 Not used Bit 5 0 Double wide print OFF 1 Double wide print ON Bit 4 0 Double high print OFF 1 Double high print ON Bit 3 0 Emphasized print OFF 1 Emphasized print ON Bit 2 Not used Bit 1 Not used Bit 0 0 FontA 12x24 1 FontB 9x17 Both double wide and double high can be selected for any of the type faces When a printed line contains characters with different heights the characters are arranged so that bottoms of all characters line up All characters printed can be underlined except 90 degree rotated characters The space caused by the tab command HT is not underlined The thickness of the underline is defined by ESC regardless of the character size Default Ohex 12 x 24 matrix Set Bit Image Mode ESC m n1 n2 d1 dn 1B 2A m n1 n2 data Specifies and prints bit image graphics _SetBit Image Mode m Mode Vertical dot Horizontal Number of density dotdensity data bytes 00 hex 8 Single density 67 7 dpi 101 6 dpi n1 n2 256 01 hex 8 Double 67 7 dpi 203 2 dpi n1 n2 256 density 20 hex 24 Single 203 2 dpi 101 6 dpi n1 n2 256 3 density 21 hex 24 Double 203 2 dpi 203 2 dpi n1 n2 256 density Set Bit Image Mode If m is not one of the specified values the r
2. Response to Status Commands Response to Bit Pattern GS r OxxOxxxx XON 00010001 XOF 00010011 DLE EOT Oxx1xx10 ASB 1 byte OXx1xx00 ASB 2 4 OxxOxxxx Response to Status Commands The transmit buffer is 99 bytes long If more than 99 bytes are stored up without being transmitted the status bytes that have no place to be stored will be thrown away Status Commands Name Command Command n Description ASCII data byte hex Real time STATUS DLE EOT 10 04 n See section 4 4 5 L request AO Transmit printer ID GSl n 1D 49 n See section 4 4 5 Enable disable GS a n 1D 61 n See section 4 4 5 Automatic Status Back ASB III Status Commande 4 4 3 Bar Code Commands Bar Code Commands Name Command Command Description ASCII n data byte hex position for HRI no HRI printed n 1 either characters 01hex or 31hex HRI printed above the bar code n 2 either 02hex or 32hex HRI printed below the bar code n 3 either 03hex or 33hex HRI printed both above and below the bar code The font used is specified by GS f Default 0 Select font for HRI GS f n 1D 66 n n 0 either OOhex or 30hex Select print GS Hn 1D 48 n n 0 either OOhex or 30hex print the HRI using FontA 12x24 n 1 either 01hex or 31hex print the HRI using FontB 9x17 Default 0 MTP 1530II User Manual
3. eitidAA Esfkfooo0uuyolaes 0xf i an amiy CER LIAAAS Inde b Tb ta A bgp Ae ae BPEEEeLTIIS hal 6B6066ubb oDyy A AA MTP 1530II User Manual Revision 20120510 Page 81 Telpar MTP 1530II Receipt Thermal Printer User Manual 6 3 Dimensional Drawings of MTP 1530II 80 mm Side view of Printer PAN bi Paper Roll Loading Side Bottom view of Printer Side View of Printer printer is shown upside down resting on its top The cutout in the side chassis which allow e q l access to the Tech DIPSWITCH and Diagnostic LEDs is shown MTP 1530Il User Manual Revision 20120510 Page 82 Telpar MTP 1530II Receipt Thermal Printer User Manual Dimensional Drawings of MTP 1532 82 5 mm Version LOW PAPER Back View of Printer Printer resting on its side with Paper MICRO SWITCH Spindle pointing up MULTECOMMUNICATION PORT POWER INPUT 24W 3 PIN POWER MTP 1530II User Manual Revision 20120510 Page 83
4. Set Reset ESC n 1B7B n LSB 1 upside down printing LSB Inverted 0 normal printing This command must print be received at the start of a line to be in effect for that line Does not apply in page mode Select GS n 1D21 n Characters can be printed in sizes from MTP 1530ll User Manual Revision 20120510 Telpar MTP 1530II Receipt Thermal Printer User Manual character 1 to 8 times normal in either width or size height Bits 0 1 and 2 set the character width multiplier Bits 4 5 and 6 set the character height multiplier A value of 0 Normal size Does not apply to HRI characters when printing bar codes See ESC Test print GS A02hex 1D 28 41 n 00r 1 or 2 00 01 02 30 31 or OOhex n m 02 00 n 32 hex m 1 01 or 31 hex causes a m Hexadecimal dump print pattern m 2 02 or 32 hex causes a Printer Status print pattern m 3 03 or 33 hex causes a barber pole print pattern Must be received at the start of a line A cut is performed following the print test The printer is reset following the print test even download characters or bit image are erased Reverse GS B n 1D 42 n Bit 0 0 default turns off and bit 0 1 video turns on reverse video printing Does not apply to bit image user defined bit image bar codes and the HRI part of bar codes or spaces skipped by HT ESC or ESC commands Does not affect the space between character lines Under
5. APDMAN opens a program which allows you to modify the current printer driver installation configuration e Double clicking the txt file will open the read me text file which will provide technical details about the printer driver software MTP 1530II User Manual Revision 20120510 Page 69 Telpar MTP 1530II Receipt Thermal Printer User Manual 6 Specifications 6 1 General Specifications General Specifications Specifications MTP 1530 Printing method Thermal sensitive line dot method Dot Structure 576 dots line Dot Density 0 125 mm 8 dot mm Dot density 203dpi X 203 dpi dpi Dots per Inch Effective printing area 72 mm Paper type Thermal Sensitive paper Paper width 79 5 0 5 mm Paper thickness 56 150 um 0 0022 0 0059 Cutting type Full or partial Depends on printer mechanism Number of columns 48 columns line default 12x24 dot font Approx 66 lines per second Font A printing line spacing 30 dots Approx 177 mm s 4 61 in s for barcodes NOTE Print speed may be slower depending on data transmission rate control commands used environmental conditions supply voltage and print density selected FontA 12x24 dots Printing speed Approx 9 84 in s 250 mm second Character composition Number of characters per line 48 columns FontB 9x17 dots CHARACTER SIZE mm 1 25 W by 3 0 H 12x24 9x17 normal
6. MTP 1530Il Modular Thermal Printer User Manual ELPAR Your Printer Solutions Company Telpar 800 872 4886 Fax 603 742 9938 Website www telpar com E mail info telpar com 2012 Telpar Rev 20120510 Telpar MTP 1530II Receipt Thermal Printer User Manual Warranty Telpar Printer Limited Warranty WARRANTIES AND DISCLAIMERS Products manufactured by Telpar are warranted against defects in workmanship and materials for a period of twelve 12 months from the date of shipment to the original user provided the Product a remains unmodified b is used only in the United States or Canada c Is Operated under normal and proper conditions as Telpar determines in its sole discretion and d Customer provides prompt written notice Telpar of any defects as to parts and or workmanship to Telpar may provide an extended warranty on certain Products or components thereof for an additional price determined solely by Telpar and such extended warranty shall only be effective to the extent memorialized in writing by Telpar Telpar s sole obligation and Customer s exclusive remedy for defective Telpar manufactured Products is limited to repair or replacement as Telpar determines in its sole discretion The warranty described above does not include any labor or service costs for removing or replacing parts or any shipping charges Any repair performed by Telpar under this warranty does not extend the original warranty period of any Prod
7. e SNMP Version SNMP vi RFC1157 compliant SNMP v2 not supported e Transport Protocol UDP IP e Community each item may be up to 16 ASCII characters Community Object Attribute Default 1 Read only public 2 Read Write None Trap 1 Read Write None Trap 2 Read Write None Trap Destination Up to two settable IP Addresses e MIB Support Part of MIB II RFC1213 Part of Printer MIB Part of Host Resource MIB Part of Print Server MIB Part of Printer MIB e PDU Support Get Request Get Next Request Set Response Trap e Server Port Number 161 e Trap Sending Port Number 162 ENCP e Protocol UDP IP e UDP Port Number 3289 e Compatible packet types Probe Initialize Query Setup Notify Automatic IP Address Protocols Automatic IP addressing is executed in the order shown in the table below If DHCP is disabled or IP addressing for DHCP fails then IP addressing for the next protocol is executed If APIPA is disabled or IP address cannot be obtained use the internal setting parameters Protocol Order Application DHCP 1 Obtains IP address APIPA 2 Assigns IP address Manual setting 3 Uses the internal set parameters IP Address obtainment with DHCP When a DHCP client boots up it searches a DHCP server for an IP address subnet mask and other possible DHCP options configured on the server and they are temporarily assign
8. Hexadecimal Dumping WW TI WW N OFF OFF VendorClass ON Printer Class OFF WW NA _ NA M SS Page 21 Telpar MTP 1530II Receipt Thermal Printer User Manual DIP Switch 2 DSW2 Settings For Serial RS 232 Communications Only S witc h Position Switch Function Description Switch Position Result Shipping No Default RESERVED 1 Fixed to OFF NA K OFF RESERVED 2 Fixed to OFF on SS OFF L DSRR e Im Disabled gt ON Enabled Orr 4 Handshaking OFF HARDWARE DTR DSR or CTS RTS OFF on XON XOFF 5 Parity Check OFF Disabled ON Enabled OFF 6 Parity ODD or EVEN OFF ON EVEN OFF 7 Transmission Speed Baud Rate ON See Switches 7 and 8 control the rate at which Table the printer receives and transmits SEE THE TABLE BELOW TO Below information in bits per second bps DETERMINE THE SWITCH 8 The default value for the RS 232 serial a alo a OFF 8 FOR THE VARIOUS BAUD NS printer is 19200 bits per second 8 Data RATES AVAILABLE Tab Bits fixed 1 Stop Bit fixed No Parity res and Hardware Handshaking Transmission Speed Baud Rate in Bits per second bps DIP Switch 2 DSW2 Pertains to DIP Switch 2 DS W2 serial printer ONLY and relate Switch Position to the settings of switch positions 7 and 8 7 8 Auto Detect ON ON This setting automatically detects the transmission
9. L pL pH m fn a kcl kc2 b xL XH yL yH c d1 dk 1 c d1 dk b fn 67 1D 28 4C pL pH m fn kc1 kc2 Description Defines the NV graphics data raster format as a record specified by the key codes kc1 kc2 in the NV graphics area b specifies the number of the color of the defined data XL xH specify the number of dots in the horizontal direction as xL xH X 256 yL yH specify the number of dots in the vertical direction as yL yH X 256 c specifies the color of the defined data colori 49 d specifies the defined data raster format Range e ForGS L 12 lt pL pH X 256 lt 65535 0 lt pL lt 255 0 lt pH lt 255 For GS 8 L 12 lt p1 p2 X 256 p3 X 65 536 p4 X 16 777 216 lt 4 294 967 295 O lt p1 lt 255 0 lt p2 lt 255 0 lt p3 lt 255 O lt p4 lt 255 m 48 fn 67 a 48 32 lt kc1 lt 126 32 lt kc2 lt 126 b 1 1 lt xL xH A 256 lt 8192 0 lt xL lt 255 0 lt xH lt 32 1 lt yL yH A 256 lt 2304 0 lt yL lt 255 0 lt yH lt 9 c 49 O lt d lt 255 k int xL xH X 256 7 8 X yL yH X 256 Maximum capacity size 256KB MTP 1530II User Manual Revision 20120510 Page 51 Telpar MTP 1530II Receipt Thermal Printer User Manual NOTES regarding lt Function 67 gt e In cases where there is sufficient capacity is not available for storing NV graphics data specified by XL XH 256 and yL yH 256 this function is ignored e The number of items of N
10. Select justification General Setting__ Start line Value ESC c 3 Select paper sensors to General Setting Yes Yes output paper out signal SS MTP 1530II User Manual Revision 20120510 Page 28 Telpar MTP 1530II Receipt Thermal Printer User Manual ESC c 4 Select paper sensors to stop General Setting Yes Yes fe A 2 PS PR ESC c 5 Enable disable panel General Setting Yes Yes buttons H i ATT AE ESC d_ Print and feed n lines General Execute Yes Yes ESCt Select character code table General Setting Yes Yes ESC Turn inverted print on off General Setting Start line Value FS p Print NV bit image NV 8 DL Execute Yes Disabl OBSOLETE Use ed GS L lt Function 69 gt hp instead o FS q Define NV bit image NV 8 DL Setting Start line Disabl OBSOLETE Use ed GS L lt Function 67 gt o instead nstead H AAA AA A nam c GS FF Feed paper to Black Mark Top of Form Execute Yes Yes GS Select character size General Setting Yes Yes GS Set absolute vertical print PAGE Execute Ignored Yes postin ft ft WE GS Define download bit image NV 8 DL Setting Yes Yes GS A Execute test print General Execute Yes Ignore d GS E User setup commands Seldom Execute Start line Disabl Setting ed GS F Set adjustment values
11. p1 p2 256 can vary from 10 dec to 65530 dec The data structure is a 1 followed by b8 through b1 a1 01 hex through 08 hex specifies the memory switch to be changed b8 represents position 8 of that memory switch and so on through b1 represents position 1 of that memory switch then another a followed by b8 through b1 can follow as specified by Telpar MTP 1530II Receipt Thermal Printer User Manual the values of p1 and p2 The values for each b are 30 hex to set a switch OFF 31 hex to set a switch ON or 32 hex to leave a switch unchanged 32 hex should be sent for the reserved switches The switch changes made become effective after a reset or power cycle Running a self test printout can check the switch settings Frequent writes may damage the NV memory Maximum recommended usage is 10 times per day Function 4 causes the printer to transmit the settings of a memory switch m 04 hex p1 02 hex p2 00 hex The data byte value is from 1 hex through 08 hex to specify which memory switch is being checked The eleven data bytes transmitted are 37 hex 21 hex 8 data bytes representing the 8 switch positions and 00 hex The 8 data bytes are transmitted in the order of switch position 8 through switch position 1 For each switch position the data sent will be 30 hex an ASCII 0 if the switch is OFF or 31 hex an ASCII 1 if the switch is ON adjustment values Effective only when the BM sensor is enabled a 01 he
12. y1 y2 256 8 number of dots being defined in the vertical direction Each NV bit image is terminated with a sequential number n x1 and y1 can range from O through 255 x2 can range from 1 through 3 y2 can range from 0 through 1 but x1 x2 256 can not be less than 1 or greater than 1023 and y1 y2 256 can not be less than 1 or greater than 288 The amount of data needed to complete this command is x1 x2 256 y1 y2 256 8 bytes Each bit image stored requires an additional 4 bytes for header information A total of 192 Kbytes is available for storage of all NV bit images This command clears all previously stored NV bit images so to n 1 through 255 defines the write a new NV bit image requires Telpar MTP 1530II Receipt Thermal Printer User Manual reloading all NV bit images which are to be stored When this command is completed the printer performs a hardware reset so all user defined characters downloaded bit images and macros are cleared and all functions are the same as if power was turned off then back on In standard mode this command must be received at the start of a line This command does nothing in page mode Define download bit image x 1 to 255dec defines the horizontal size as x times 8 dots y 1 to 48dec defines the vertical size as y times 8 dots x times y cannot exceed 1536 The download bit image is cleared by a power on reset ESC or ESC amp a download bit image GS and use
13. 8 7or8 0 9 04 hex CODE39 variable 0 9 A Z space 05 hex l2of5 even number 0 9 06 hex CODABAR variable 0 9 A B C D Bar Code Commands Notes MTP 1530II User Manual Revision 20120510 Page 56 Telpar MTP 1530II Receipt Thermal Printer User Manual EE For UPC A or UPC E Printing starts after 12 data bytes are received For JAN13 EAN13 Printing starts after 13 data bytes are received For JAN8 EAN8 Printing starts after 8 data bytes are received For ITF the number of data bytes must be an even number 4 5 9 GS k m n d1 dn 1D 6B m n DATA For m 41hex through 49hex m selects the bar code type n number of data bytes to follow Bar Code Command Values m Bar Code n dec Valid data 41 hex UPC A 11or 12 0 9 42 hex UPC E 11or 12 0 9 43 hex JAN EAN 13 12 or 13 0 9 44 hex JAN EAN 8 7or8 0 9 45 hex CODE39 1 thru 255 0 9 A Z space i 46hex 120f5 even 1 thru255 0 9 47hex CODABAR 1 thru 255 0 9 A B C D 48hex Code93 1 thru 255 OOhex thru 7Fhex 49hex Code128 2 thru 255 OOhex thru 7Fhex Bar Code Command Values Notes 1 2 n indicates the number of data bytes which follow If n is outside the allowable range the command aborts and following data is treated as normal data Notes when CODE93 m 48hex is used 1 In
14. HUB None USB packet size in full speed connection USB bulk OUT TM 64 bytes USB bulk IN TM 64 bytes USB device class USB device class USB vendor defined class and USB printer class The setting value of DIP switch 1 7 specifies the class at power on USB Descriptor Table USB Vendor defined class USB printer class Vendor ID 04B8h 04B8h Product ID 0202h 0E02h String Descriptor Manufacturer EPSON EPSON Product BA T500ll BA T500ll Serial Number Character string based on the product serial number Character string based on the product serial number MTP 1530ll User Manual Revision 20120510 Page 63 Telpar MTP 1530II Receipt Thermal Printer User Manual 4 8 Ethernet Interface General Features 10BASE T and 100BASE TX Ethernet communication full half duplex Auto negotiation or manual setting e Complies with TCP IP protocol LP LPR and socket communications IP address setting with arp ping Support to DHCP Support to APIPA Ping response Status printing function Setting initialization of this module with a push button Status monitoring with ENPC Status monitoring with SNMP Circuit Board Push Button Setting Factory Defaults Holding down the push button while turning on the printer power and continuing to hold it on for five seconds or more causes all of the internal setting parameters to return to their factory default values Status sheet printing H
15. ON High voltage The power supply NOT RECOVERABLE Turn condition followed by another blink voltage is too high power OFF correct the problem OFF before the cycle starts again before turning back on each cycle is approx 5 seconds long 3 blinks OFF then a paused ON Low voltage The power supply NOT RECOVERABLE Turn condition followed by another blink voltage is too low power OFF correct the problem OFF before the cycle starts again before turning back on each cycle is approx 5 seconds long 4 blinks OFF then a paused ON CPU error The CPU executes NOT RECOVERABLE Cycle condition followed by another blink an incorrect power off and on to see if the OFF before the cycle starts again address or the I F error goes away each cycle is approx 5 seconds board is not long connected 6 blinks ON then a paused OFF Platen open Print is not Recovers by DLE ENQ1 or DLE condition before the cycle starts performed due to ENQ2 after the platen is closed again each cycle is approx 5 the platen being seconds long open 4 blinks ON then a paused OFF Paper J am A paper Jam has Open the platen and remove condition before the cycle starts Error occurred the jammed paper Recovers again each cycle is approx 5 by DLE ENQ1 or DLE ENQ2 seconds long Printer operation when an error occurs The printer executes the following operations when detecting an error e Stops all printer operations for the selected paper section
16. bytes The flow control information is sent to the host using hardware or software protocols as determined by the DIP switch settings The hardware protocol uses the DTR line of the serial interface This pin are asserted or negated as necessary to turn off and turn on the flow of data The software protocol uses the XON 11hex and XOFF 13hex ASCII control codes which are sent back to the host to start and stop the data stream When XON XOF handshaking is enabled the XON and XOF are transmitted without checking the state of the DSR line of the I O connector Some host systems may not support one or both of these protocols lf memory switch 1 position 3 is set to OFF and DTR handshaking is enabled then the DTR line goes to the BUSY state whenever the printer is OFF LINE see section 1 1 3 add bookmark or when the receive buffer is full If memory switch 1 position 3 is set to ON and DIR handshaking is enabled then the DTR line goes to the BUSY state from the time power is turned on until the printer is ready to receive data Page 60 Telpar MTP 1530II Receipt Thermal Printer User Manual during self test or when the receive buffer is full If XON XOF is enabled then the DTR line goes to the BUSY state from the time power is turned on until the printer is ready to receive data or during self test If XON XOF handshaking is enabled the printer sends XON when the printer goes On Line after a power on when the receive buffer becomes avai
17. character set Set values independently in Page and Normal modes MTP 1530II User Manual Revision 20120510 Telpar MTP 1530II Receipt Thermal Printer User Manual Set Print mode ESC n 1B 21 n Set Print mode See Section 4 5 1 Set Print Mode See ESC M ESC E ESC Set absolute ESC n 1B 24 n m Current print position is set to n m x print position m 256 x 0 125 mm from the beginning of the line See ESC V GS GS See Po Page mode Select Bit ESC m 1B 2A m Set Bit Image mode See 4 5 2 Set Bit Image mode 1 n2 n1 n2 Image Mode d1 dn data Turn underline ESC n 1B 2D n n 0 00 or 30 hex Turn underline off mode on off n 1 01 or 31 hex Turn on 1 dot line high underline n 2 02 or 32 hex Turn on 2 dot line high underline See ESC Set default line ESC 2 1B 32 Set 3 75 mm line spacing 30 dot lines spacing See ESC 3 Set Line feed ESC 3 n 1B 33 n Set single line spacing to n dot lines n x pitch 0 125mm Set independently in Page and Normal mode Default 30 See Printer reset ESC 1B 40 Resets the printer to the mode it was in when power was turned on Clears the data in the print buffer but does not the data in the receive buffer The DIP switches and MEMORY switches are not rechecked The MACRO delinition is not Set Horizontal ESC D 1B 44 Set from 1 to 32 tab positions Data Tab positions d1 dn DATA 00 values range from 1 to 255 in ascending NUL orde
18. command ESC tn n Character Set Description Page number to see sample 0 PC437 U S A Standard Europe 72 1 Katakana 73 2 PC850 Multilingual 74 3 PC860 Portuguese 75 4 PC863 Canadian French 76 5 PC865 Nordic 77 16 WPC 1252 78 17 PC866 Cyrillic 2 79 18 PC852 Latin 2 80 19 PC858 Euro 81 MTP 1530II User Manual Revision 20120510 Page 71 Telpar MTP 1530II Receipt Thermal Printer User Manual PC 437 U S A Standard Europe Character Set n 0 20 30 40 50 60 70 80 90 AU BO CO DO EO FO MTP 1500 CHARACTER SET PC437 U S A Standard Europe Power On default or ESC t OOhex 0123456789ABCDEF nn 0123455678981 lt gt 7 OABCDEFGHIJKLMNO PQRSTUVWXYZ 7 _ abcdefghijkimno parstuvwxyz d eitiA EekROGdGUUVYOUGCE A Ff T 6UA AL FJ SNP lid daad Inda bt t te ee tea tH tert tee ttt rial aBfrioutrtON nmeen s ssli s 147 MTP 1530II User Manual Revision 20120510 Page 72 Telpar MTP 1530II Receipt Thermal Printer User Manual Katakana Character Set n 1 MTP 1500 CHARACTER SET Katakana ESC t Olhex 0123456789ABCDEF 20 I HERB 90 01239456789 lt gt 40 ABCDEFGHIJKLMNO 50 PQRSTUVWXYZ _ 6 abcdefghijkimno 70 parstuvwxyz 80 _ eee and 1 11000 SL ed P Era te py AQ o jJ 27749014113 BO 49134153 25395 279 CO 9F 4Y7FRF2Z24J NE7IARY DO EO FFI A
19. condition settings of the serial interface host Available settings are 2400 4800 9600 19200 38400 57600 and 115200 9600 only OFF ON 19200 only ON OFF 38400 only OFF OFF MTP 1530II User Manual Revision 20120510 Page 22 Telpar MTP 1530II Receipt Thermal Printer User Manual There are 8 MEMORY Switches only four are currently used Memory Switch 1 Position State Function Default ON RESERVED OFF 0 1 OFF ON RESERVED OFF 0 2 OFF ON BUSY condition when buffer is full OFF 0 3 OFF BUSY when buffer is full or when OFF LINE ON Receive error is ignored serial interface only OFF 0 4 OFF Receive error prints serial interface only ON Auto line feed enabled Parallel interface only OFF 0 5 OFF Auto line feed disabled ON RESERVED OFF 0 6 OFF ON RESERVED OFF 0 7 OFF ON RESERVED OFF 0 8 OFF Memory Switch 5 Position State Function Default ON RESERVED OFF 0 1 OFF ON Near Paper End Sensor Installed ON 1 2 OFF Near Paper End Sensor NOT Installed ON Printer can recover from a recoverable error after a paper jam has OFF 0 3 occurred OFF Printer goes Offline after a paper jam has occurred ON Enable Paper Jam Detection OFF 0 4 OFF Disable Paper Jam Detection ON RESERVED OFF 0 5 OFF O
20. data 67 GS L pL pH m fn a kc1 kc2 b 67 Define the NV graphics data raster format xL xH yL yH c d1 dk 1 c d1 dk b 69 GS LpLpHmfnkclkc2xy 69 Print the specified NV graphics data 112 GS LpLpHmfnabxbyc 112 Store the graphics data in the print buffer raster format xL xH yL yH d1 dk MTP 1530II User Manual Revision 20120510 Page 49 Telpar MTP 1530II Receipt Thermal Printer User Manual Notes pertaining to GS L and GS 8 L e Frequent write command executions by an NV memory write command may damage the NV memory Therefore it is recommended to limit writing of the commands into the NV memory to 10 times or less a day e If the power is turned off or the printer is reset via an interface while this command is being executed the printer may go into an abnormal condition Be careful not to turn the power off or let the printer be reset via an interface while this command is being executed e While processing this command the printer is BUSY while writing the data to the NV memory and stops receiving data Therefore be sure not to transmit data from the host PC while the printer is BUSY When lt Function 48 51 or 64 gt is transmitted do not transmit the subsequent data until the status is received ESC POS Handshaking Protocol procedures is required when using lt Function 64 gt lt Function 48 gt GS L pL pH m fn fn 0 48 1D 28 4C pL pH m fn Description Transmits the entire capacity of th
21. detects that the platen is not locked in place against the print mechanism 4 Paper Jam Sensor This sensor located near the platen long rubber roll detects whether or not paper has started to wrap around the platen which would result in a paper jam If this sensor detects that the paper is wrapping around the platen all printing operation will stop until the jam is cleared and the paper path is returned to normal Ha paper jam does occur turn the printer off carefully remove the jammed paper and then turn the printer on again 5 Paper Low Sensor A small micro switch mounted on the side of the chassis see photo below detects the presence of a paper roll diameter that is approximately 2 8 to 2 9 inches mm or greater If the roll falls below this diameter then the PAPER OUT LED middle LED on the printer s control board see section 4 1 1 lights to alert that the paper roll is getting low If Escape Command ESC c 4 has been sent to the printer prior to the paper low condition and the paper level falls below the micro switch sensor then the printer will stop printing operation immediately 6 Black Mark Sensor please reference section 2 2 2 for more information on Black Mark detection This sensor detects a black mark that has been pre printed on the side of the paper Usually the black mark denotes the top or starting point of each individual receipt contained in a continuous roll of pre printed paper If the paper you are using ha
22. e Goes BUSY When memory switch 1 3 is set to off to go BUSY during printer offline e Flashes the ERROR LED MTP 1530II User Manual Revision 20120510 Page 27 Telpar MTP 1530II Receipt Thermal Printer User Manual 4 3 Control Codes and Control Sequences List Location of Class Standard Page Definition mode mode HT Horizontal tab General Execute Yes Yes LF Print and line feed General Execute Yes Yes FF PAGE MODE print and PAGE Execute Ignored Yes return to standard mode 4 Black Mark mode print and General Top of Execute Yes Disabl feed to print starting Form ed position Black Mark ASS CR Print and carriage return General Execute Yes Yes CAN _ Cancel print data PAGE Execute Ignored Yes DLE Real time status request STATUS Execute Yes Yes RENE S c DLE Real time request to printer General Execute Yes Yes ESC Escape sequence header FS FS sequence header GS GS sequence header ESC FF Print data PAGE Execute Ignored Yes ESC SP Set right side character General Setting Yes Yes Q I spacing O j j ESC Set print mode s General Setting Yes Yes ESC Set absolute print position General PAGE Execute Yes Yes ESC Sel
23. left to right n 1 either 01 hex or 31 hex sets the starting position to the lower left corner and printing goes from bottom to top n 2 either 02 hex or 32 hex sets the starting position to the lower right corner and printing goes from right to left n 3 either 03 hex or 33 hex sets the starting position to the upper right corner and printing goes from top to Sets the position where data is bottom mode set In page printing area X2 y1 y2 dx1 dx2 dy1 dy2 1B 57 x1 X2 y1 y2 0dx1 dx2 dy1 dy2 position y1 y2 256 vertical starting position dx1 dx2 256 printing area width dy1 dy2 256 printing area height Defaults are X1 x2 y1 y2 0 dx1 128 for 82 5 mm printer or 64 for 80 mm printer dx2 2 dy1 152 for 82 5 mm printer X1 x2 256 horizontal starting or 226 for 80 mm printer dy2 2 Set relative print position ESC n m 1B 5C n m position plus n m 256 0 125 mm If the starting position is set by ESC T to the upper left or lower right of the printing area then the offset is in the horizontal direction but if the starting position is set to the upper right or lower left of the printing area then the offset is in the vertical Set printing position to current direction Set absolute vertical print Page mode position 1D 24 n m position to buffer character data to n m 256 0 125 mm referenced to the starting posotopn defined by ESC T If the starting position is
24. m1 m2 256 and n and r are not 0 Count down mode is set when n1 n2 256 gt m1 m2 256 and n and r are not 0 Counting stops when n1 n2 256 m1 m2 256 and n and r are not 0 n the amount to increment the count by R the repetition number when counter n1 n2 256 start count value is fixed Set counter GS C 2 n1 n2 1D 43 32 n1 n2 n1 n2 256 sets the value of the serial number counter In count up mode if the counter value goes outside the counter operation range set by GS C 1 or GS C it is forced to convert to the minimum value set by GS c In count down mode if the counter value goes outside the counter operation range set by GS C MTP 1530II User Manual Revision 20120510 Telpar MTP 1530II Receipt Thermal Printer User Manual 1 or GS C it is forced to convert to the maximum value set by GS c Select count GS C si 1D 43 3B s1 s1 through s5 are all character mode B S2 S3 S4 3B s2 3B s3 strings made up of the ASCII S5 3B s4 3B s5 characters 0 through 9 s1 and s2 range from 0 to 65535 and s3 through s5 range from 0 to 255 s1 and s2 specify the counter range s3 the amount to increment the count by S4 the repetition number when the counter value is fixed s5 the counter value Count up mode is selected by s1 lt s2 and s3 and s4 are not 0 Count down mode is selected by s1 gt s2 and s3 and s4 are not 0 Counting stops when s1 ll das orsS 0ors4 0 _ Print counter G
25. or ESC amp A download bit image GS and user defined characters ESC amp can not be defined simultaneously defining either will cancel the other An NV bit image is stored in non volatile memory and is cleared only by redefining the NV bit image message Frequent writes may damage the NV memory Maximum recommended usage is 10 times per day Bar Code Commands Name Command Command ASCII n data byte hex PrintNV FSp n m 1C70 n m image Define NV FS q n x1 1C 71 n x1 image X2 y1 y2 X2 y1 y2 data 01 hex data 01 hex through x1 through x1 X2 y1 y2 X2 y1 y2 data n hex data n hex MTP 1530II User Manual Revision 20120510 FS q in the resolution specified by m m 0 either 00 hex or 30 hex 203 by 203 density m 1 either 01 hex or 31 hex 203 V by 102 H density m 2 either 02 hex or 32hex 102 V by 203 H density m 3 either 03 hex or 33 hex 102 V by 102 H density Must be received when the print buffer is empty Is not affected by print modes emphasized double strike underline character size reverse video rotated etc but is affected by upside down printing mode Data which exceeds the allowable print width of the printer is ignored This Print the NV message n defined by command is ignored in Page mode number of NV bit images to be stored in memory For each NV bit image x1 x2 256 8 number of dots being defined in the horizontal direction and
26. size 0 88 W by 2 13 H Receive Buffer 4 KB Interface options IEEE 1284 Centronics Parallel RS232C Serial Ethernet 10BASE T and 100BASE TX Dimensions of printer See Section 6 3 for detailed dimension information Weight of printer no paper roll Approx 3 6 Ibs 1 6 Kg Power For head See Section 1 5 Power Supply Requirements Supply For motor DC 24V 5 1 A typical while feeding paper For cutter DC 24V 5 0 9 A max 0 11A typical Expected Mechanism 15 million lines except print head amp cutter Life Print head 100 million pulses Cutter 1 million cuts 750 000 when 30 degrees C or above and 60 RH or above Environ Operating temperature 20 to 60 C 4F to 140F mental Operating humidity 10 to 85 RH No condensation condition Storage temperature 25 to 70 C Storage humidity 10 to 90 RH No condensation except for paper Detection Head temperature By thermistor applied energy control abnormal temperature detection Paper present out By photointerrupter Platen open Paper low Micro switch Black Mark optional Reflective photosensor MTP 1530ll User Manual Revision 20120510 Page 70 Telpar MTP 1530II Receipt Thermal Printer User Manual 6 2 Character Sets 6 2 1 Overview Overview of Character Sets Select character code table with
27. these actions All electrical mechanical portions of the printer are exercised and checked by this action except for the host to printer communication interface components The Power Switch is located at the The Paper Feed Button is located rear of the printer next to the power on the top side chassis of the inlet connector Pressing the 1 printer This button will feed paper position on the power switch applies through the printer while it is power to the printer and pressing the pressed and the button is also used 0 position on the switch switches off together with the power button to power from the printer print a Self Test printout MTP 1530II User Manual Revision 20120510 Page 18 Telpar MTP 1530II Receipt Thermal Printer User Manual SELF TEST Firmware Version 1 00 Parallel Interface Buffer Capacity 4K bytes Handshaking Operation busy condition Receive buffer full Automatic Line Feed CR command function Disabled Resident Character Alphanumeric Print Density LIGHT 1 2 3 4 DARK Power On Status Disabled DIP Switch 1 12345678 ON OF AIR DIP Switch 2 12345678 k ON H OFF III Memory Switch 1 12345678 ON OFF BE HHEHBHEI Memory Switch 8 12345678 ON H OFF AIR If you want to continue SELF TEST printing please press FEED button MTP 1530II Self Test Printout MTP 1530II User Manual Revision 20120510 Page 19 Telpar MTP 1530II Receipt The
28. 1530II User Manual Revision 20120510 Page 20 Telpar MTP 1530II Receipt Thermal Printer User Manual DIP Switch 1 DSW1 Settings Switch Position No Black Mark Sensor BM Sensor If this switch is set to the ON position you must use special black mark paper or the printer will go into an error mode see section 2 2 2 Setting of Allowable Print Width 2 The MTP 1530II should always have this switch set to the ON position Print Darkness Selection To help achieve the maximum lifespan of the print head it is recommended that these switches be set to the lowest intensity level available which still adequately meets the desired print darkness for your printer application Factory Setting Fixed to OFF Selection of Interface Class Effective with the USB interface type only Reserved fixed to Off with other interface types Reserved Fixed to OFF DIP Switch 1 DSW1 Settings MTP 1530II User Manual Revision 20120510 Switch Position Result Shipping Default OFF Noblack mark detection TI T OFF ON Detects black marks on paper RO od EE A A ON ON 576 dots line Switch Switch Darkness 3 4 Setting on oN Slightlylight Medium OFF OFF Medium OFF and OFF ON OFF Slightly dark OFF ON Dark OFF Noma Printing OFF ON
29. 2 ADDIICAUONS 5 uu aaa aaa a kuyaq 9 1 3 Standard Features uuu l u D ten en min nue 10 UR OCH d le La EEN 11 15 Power Supply Requirements l U U U u u 11 1 5 1 Voltage 24 NDC An 11 1 5 2 Power Supply Option from Telpar EE 11 1 5 3 3 Pin Hosiden Connector on Printer for Power Supply Connection 12 1 6 Telpar Roll Paper for MTP 1530l1 Series 12 1 7 Sensor Locations and Functons l U U U U U U u 13 2 Operator INSUUCUONS in 15 2 1 Unpacking ANG Jee deiere eebe eege geen needed 15 22 Paper Loadihi ira 15 221 Ee Rol a 15 22 2 Black Mark Sensors LO ns nee 15 Zid Paper alfa 17 2 011 Head Open Leve E 17 3 InstalatoON airi a 18 SL SCI Test MO de ia 18 4 Setup and Control of the Printer U U 20 4 1 DIP Switch Settings and Memory Switch Settings 20 4 2 LEDs and Error indication 26 4 3 Control Codes and Control Sequences List 28 4 4 Control Codes and Control Sequences Definition 31 4 4 1 General Usage Print Commande 31 442 Slas lgl Tue EE 35 443 Bar Code Command Sior RS dt de nee 35 AAA Coume COMMANAS LL li 36 MTP 1530Il User Manual Rev
30. 20120510 Page iii Telpar MTP 1530II Receipt Thermal Printer User Manual AAS TOP Ol FORM COMMA S una eine 38 446 Page Mode Command Sii a 38 4 4 7 NV Memory and Down Load Bit Images Commands 41 4 49 Seldom Used COMMANA ista aos 43 A5 A kl u uu u u 46 a Giel NEW u uuu AE 46 4562 Se Bl IMAGE ee EE 46 4 5 3 Set Raster Bit Image Mode Error Bookmark not defined 4 5 4 Set and Process Graphics Data 49 Aoi Status COMMAndS EE 54 4 5 6 Enable Disable Auto Status Back ASB mode 55 4 57 Salus Bytes Transmed sii tarte ne 55 45 6 Bar Code Command Aimants ete ie D tata 56 4 5 9 GS k m n d1 dn 1D 6B m n DATA 57 AG Serial RS Z352C Interface ion 59 4 6 1 Serial RS232C Interface Specification nnneennennnennnnnnrnnsnennnnnsrerrrrsrrrrnrssrennn 59 4 02 Sena COMMS Ct ON Lu taster calc alii 59 AiG GT E COMING uu uyum cial 60 4 7 Centronics Parallel IEEE 1284 Interface Q U 62 ATL Paralelo CONnNeCiOr us u Zx a m uu Sul sas 62 4 8 USB 2 0 IN ace sisi l u u uu a S uuu s SSS 63 49 ElernetinterlaCO iia 64 5 Drivers f r th Pantera 69 EC E e arni a Tu Sasu s 70 ZE WE UUCHT Tele CN 70 6 2 Character Sets iia 71 OLA e e EE 71 PC437 U S A Standard Europe Character Set 72 Katakana Character e iia oa 73 EE Eeer 74 PG600 Porugues Ch racIe o da 75 PC8
31. 4 4 5 Top of Form Commands page 38 Disabled Parameters will be processed as normal data Empty Enabled only when at the beginning of a line Ignored Command code and parameters are ignored Start line Enabled only when there is no data in the print buffer Yes Function is enabled List of Control Codes and Control Sequences Locations 4 4 Control Codes and Control Sequences Definition 4 4 1 Real time request to printer General Usage Print Commands General Usage Print Commands Command ASCII N Comman Description d hex n data byte hex 09 Move the print position to the next horizontal tab position Default is a TAB position every 8 columns See ESC D OA Print data and feed paper Default line Spacing 3 75mm See ESC 2 and ESC 3 OC See Top of Forms Commands See Page Mode Commands 0D If parallel interface is selected and automatic line feed is is enableq Memory Switch 1 5 then CR is treated 10 05 n n 01hex Recover from error and restart printing from the line where the error occurred n 02hex Recover from an error after clearing the receive and 1B ESC Sequence Header 1C FS Sequence Header 1D GS Sequence Header 1B 20 n Set spacing to the right of each Set right side character spacing ESC SP N character to n x 0 125 mm n x 0 0049 Doubled for Double Wide Does not affect the Kanji
32. 63 Canadian French Character Get 76 PCS65 NOMIC Gara Clr Se luminarias dont adela 77 WPC 1252 Te er 78 PCSG66 CynilliG 2 Character Sei ee 79 PG852 Latin 2 G aracter EE 80 MTP 1530Il User Manual Rev 20120510 Page iv Telpar MTP 1530II Receipt Thermal Printer User Manual PC858 Euro Character Set 6 3 Dimensional Drawings of the MTP 1530I1l 80 mm MTP 1530I User Manual Rev 20120510 Page v Telpar MTP 1530II Receipt Thermal Printer User Manual 1 General The MTP 1530II series of modular thermal printers is designed specifically for the high performance size and durability requirements of cut and drop applications The compact size and high performance characteristics coupled with its rugged design also make it ideal for the kiosk environment Here are some common options for the MTP 1530Il Printer Please note that all the options listed below are for use with 80mm 3 15 inch wide paper MTP 1530Il Option Description Telpar Part Number RS 232 Serial Communication Full Cut Document 901033 0202 RS 232 Serial Communication Partial Cut Document 901033 0212 Parallel Communication Full Cut Document 901033 0203 Parallel Communication Partial Document 901033 0213 USB Communication Full Cut Document 901033 0201 USB Communication Partial Cut Document 901033 0211 Ethernet network Communication Full Cut Document 901033 0204 Ethernet network Communication Partial Cu
33. FF 0 4 OFF Autocutter is installed ON Discards receive data when printer is offline OFF 0 5 OFF Keeps receive data when printer is offline ON Backwards paper feeding amount 88 steps OFF 0 6 OFF Backwards paper feeding amount 108 steps ON Enable test print when paper is loaded OFF 0 7 OFF Disable test print when paper is loaded ON Does NOT initialize for Black Mark position when power is turned on OFF 0 8 OFF Initializes for Black Mark position when power is turned on Note Not all printer mechanisms allow reverse paper feeding lf reverse feeding is allowed after cutting the paper with a GS V command paper feeds backwards The print starting position adjustment with GS F can be set to the backward direction relative to the cutting position In this case the maximum backward feed length is 14 mm 112 0 125mm MTP 1530II User Manual Revision 20120510 Page 25 Telpar MTP 1530II Receipt Thermal Printer User Manual 4 2 LEDs and Error Indication Three LEDs LED1 LED2 and LED 3 are located below the cutout in the side chassis above the DIPSWITCH and next to the on board paper feed switch as shown in the picture and figure below Location of Board Mounted LED 1 LED2 Paper Feed Switch and LED 3 On Board Paper Feed Switch LT LeD1 power OE LED2 paper out LED 3 Error DIPSWITCH LED 1 POWER LED ON means power is stable and the print
34. N Disable the USB Power Saving Function OFF 0 6 OFF Enable the USB Power Saving Function ON RESERVED OFF 0 7 OFF ON RESERVED OFF 0 8 OFF MTP 1530II User Manual Revision 20120510 Page 23 Telpar MTP 1530II Receipt Thermal Printer User Manual Memory Switch 6 Position State Function Default ON Manual Load of paper paper fed with After the platen is closed the platen open AND printer feeds the paper If Black Mark Sensor enabled approx 125mm 5 to the Black Mark position and then cuts it Auto load of paper AND After auto loading the paper If Black Mark Sensor enabled printer feeds paper to the Black Mark position and then cuts it Manual Load of paper paper fed with After the platen is closed platen open AND printer does not feed or cut If Black Mark Sensor disabled paper Auto load of paper AND After auto loading the paper OFF 0 1 If Black Mark Sensor disabled the printer feeds the paper approx 125mm 5 and then cuts it OFF Manual Load of paper fed with platen After platen is closed printer open AND feeds paper to the Black If Black Mark Sensor enabled on position and then cuts Auto load of paper AND After auto loading the paper If Black Mark Sensor enabled printer feeds paper to the Black Mark position and then cuts it Manual Load of paper paper fed with After t
35. Not used Bit4 Not used always ON Not used always ON Bit3 1 OFF LINE 0 ON LINE 1 off line 0 on line Bit 2 Not used always ON Not used always ON Bit 1 Not used always OFF Not used always ON Bit 0 Not used always OFF Not used always OFF First Status Byte Transmitted Second Status Byte Transmitted The second byte sent due to Status byte sent when DLE EOT ASB status printer 02 hex is received information Bit7 Not used always OFF Not used always OFF Bit 6 1 An automatically recoverable 1 an error occurred 0 no errors error has occurred Print head temperature or Platen open Bit 5 1 An unrecoverable error has 1 Printing is halted 0 not out of occurred Paper Bit4 Not used always OFF Not used always ON Bit 3 1 CUTTER error 1 paper is being fed by the paper feed button Bit2 Not used Bit 1 Not used 1 Platen is open BitO Not used Not used always ON MTP 1530II User Manual Revision 20120510 Page 55 Second Status Byte Transmitted Telpar MTP 1530II Receipt Thermal Printer User Manual Third Status Byte Transmitted The third byte sent due to Status byte sent when DLE EOT ASB status paper sensor 03 hex is received information Bit7 Not used always OFF Not used always OFF Bit 6 No
36. RNT SV O6 00 FO XAFARAHHRHETHREMHA Jtt AREYIITUALODI MTP 1530II User Manual Revision 20120510 Page 73 Telpar MTP 1530II Receipt Thermal Printer User Manual PC850 Multilingual Character Set n 2 20 30 40 50 60 70 80 90 AU BO CO DO EU FO MTP 1500 CHARACTER SET PC850 Multilingual ESC t 02hex 0123456789ABCDEF PU RSRE O1239456789 lt gt GABCDEFGHIJKLMNO PQRSTUVWXYZ _ abcdefghijklmno parstuvwxyz Cu e ddadac e aeisfiad E ekodouuyoUaEe Oxf AiduANASEBaAET SECHER b EH ta A hp es ate GBPEEEITIII rhal OBG0dGupPUUUYY A MTP 1530II User Manual Revision 20120510 Page 74 Telpar MTP 1530II Receipt Thermal Printer User Manual PC860 Portuguese Character Set n 3 20 30 40 50 60 70 80 90 AO BO CO DO EU FO MTP 1500 CHARACTER SET PC860 Portuguese ESC t O3hex 0123456789ABCDEF nn 0123456789 lt gt 7 GABCDEFGHIJKLMNO PQRSTUVWXYZ 7 _ abcdefghijkimno parstuvwxyz cCu diii A e EefoO1AA T0UnN BL 0 F 4 eel dd daadiadt4 sy bt t te ee te ES Her ther tts rial IP aBlriouptoONhbagen tesfi s ee SI MTP 1530II User Manual Revision 20120510 Page 75 Telpar MTP 1530II Receipt Thermal Printer User Manual PC863 Canadian French Character Set n 4 20 30 40 50 60 70 80 90 AU BU CO DO EU FO MTP 1500 CHARACTER SET PC863 Canadian Frenc
37. Revision 20120510 Page 35 Telpar MTP 1530II Receipt Thermal Printer User Manual dots Default 162 Range 1 to 255dec Print bar code GS k n data NUL 00 1D 6B n data Selects the bar code type and prints See Section 4 5 8 Bar Code Command Set bar code width GS w n 1D 77 n n defines the width of lines used for printing bar codes in mm For codes Code39 ITF and CODABAR n 2 0 250 amp 0 625 n 3 0 375 amp 1 000 n 4 0 500 amp 1 250 n 5 0 625 amp 1 625 n 6 0 750 amp 2 000 For codes UPC A UPC E JAN13 JANS Code93 and CODE128 the smaller number listed above the Modulo Width Default 3 Bar Code Commands Counter Commands Command n data byte hex 4 4 4 Counter Commands Name Command ASCII counter print m mode Select GS C 0 n 1D 43 30 n m indicated by the number value n 01 hex through 05 hex sets the number of digits to be printed m 0 either 00 hex or 30 hex align right with leading spaces m 1 either 01 hex or 31 hex align right with leading zero m 2 either 02 hex or 32 hex align left with trailing spaces If n 0 then m has no n 00 hex prints the actual digits meaning Default is n m 0 mode A n2 m1 Select count GS C 1 n1 M2 N r 1D 43 32 n1 n2 m1 m2 n r m1 m2 256 end count n step amount r the repetition number when the counter value is fixed Count up mode is set when nt n2 256 lt
38. S c 1D 63 Sets the serial counter value in the print buffer and increments or decrements the counter value based on the count mode selected by GS C 0 and either GS C 1 or GS C In count up mode the counter value is set to the minimum value if it goes out of the range set by GS C 1 or GS C In count down mode the counter value is set to the maximum value if it goes out of the range set by GS C 1 or GS C Counter Commands MTP 1530ll User Manual Revision 20120510 Page 37 Telpar MTP 1530II Receipt Thermal Printer User Manual DEE CC sly Description Print if needed then feed paper to the next Black Mark if the BM sensor is enabled See GS F GS FF and DSW 1 position 1 Feed paper to the next Black Mark position Ignored unless enabled by Dip SW 1 position 1 See GS F FF and Dip Switch settings For additional information black mark sensing see Section 2 2 2 Black AAN Description Print and return to standard mode Printed data is cleared from the data buffer The printing area set by ESC W is reset to the default setting See ESC FF ESC L and ESC S Cancel print data in page mode See ESC L and ESC W area Printed data is not cleared from the data buffer ESC T and ESC W values are not cleared See FF ESC Prints all buffered data in the printing L and ESC S position See ESC T set to the top left corner or the bottom right corner this is a horizontal position but w
39. Seldom Setting Yes Yes GS M Customize printer control Seldom Setting Start line Value rales o UES H e AA ee S GS Print download bit image NV amp DL Execute Empty Yes GS Start end macro definition Seldom Execute Yes Yes A LIL E E O A PR GsB Set reverse video on off General Setting Yes Yes GS CO Select counter print mode Counter Setting Yes Yes GSC1_ Select count mode A Counter Setting Yes Yes GSC2 Set counter Counter Setting Yes Yes GSC Select count mode B Counter Setting Yes Yes GSE Select head control method Seldom Setting Yes Yes GS H Select printing position of Bar Code Setting Yes Yes characters __ _ GSI Transmit printer ID Status Execute Yes Yes GSL Set left margin General Setting Start line Value GST Set print position to General Execute Yes Ignore beginningofline_______l___________ d_ GS V Select cut mode and cut General Execute Start line Yes Po paper GS W_ Set printing area width General Setting Start line Value GS Set relative vertical printing PAGE Execute Ignored Yes l position E E j GS ___ Execute macro Seldom Execute Yes Yes GSa Enable disable Auto Status Status Execute Yes Yes Back ASB Setting GSb___ Turn smoothing mode on oft ______________ Set
40. Succession or 2 by turning DIP switch DPSW2 position 5 OFF and turning power back on Print Sample Hexadecimal Dump To terminate hexadecimal dump Press Feed button three times 1B 21 00 1B 26 02 40 40 1B 69 IS oo 1B 25 01 1B 63 34 00 1B 30 31 04 01 41 42 43 44 45 46 47 48 49 4A ABCDEFGHIJ COMPLETED Hex Dump of Print Sample MTP 1530Il User Manual Rev 20120510 Page 8 Telpar MTP 1530II Receipt Thermal Printer User Manual 1 1 3 Explanation of Terms used throughout this manual Receive buffer Receives data from the host and stores the data temporarily until it can be processed to the print buffer or processed as otherwise required Print buffer Stores the image data to be printed Start of line There is no print data in the print buffer and the print position is not specified by ESC or ESC Many commands are effective only at the start of line Printable area For both Standard Mode and Page Mode the length in the horizontal direction is 72 mm 576 dots per line 8 dots per mm for an overall 80 mm paper width In page mode the length in the vertical direction is 92 mm 738 dots per line 8 dots per mm for an overall 80 mm paper width version Printing area Printing range set by command The printing area must be less than or equal to the printable area MBS Most Significant Bit of a byte of data LBS Least Significant Bit of a byte of data OFF LINE There is no swi
41. TP 1530II Receipt Thermal Printer User Manual PC866 Cyrillic 2 Character Set n 17 20 30 40 50 60 10 80 90 AU BO CO DO EO FO MTP 1500 CHARACTER SET PC866 Cyrillic 2 ESC t 11hex 0123456789ABCDEF 1448 0123456789 188572 GABCDEFGHIJKLMNO PAORSTUVNAVE NI abcdefghijklmno parstuvwxyz 7 ABBTIEX3UUKAMHON PCTYOXYUNYWYBHbBINA abBrAe X3HHAKNAMHON ble t te bp ete tent ter ttt rial IF DCTYOXUYWYbIbBAHA E beTIiVy hue MTP 1530II User Manual Revision 20120510 Page 79 Telpar MTP 1530II Receipt Thermal Printer User Manual PC852 Latin 2 Character Set n 18 20 30 40 50 60 70 80 90 AO BO CO DO EO FO MTP 1500 CHARACTER SET PC852 Latin 2 ESC t 12hex 0123456789ABCDEF 1 amp amp 0123456789 lt gt 7 ABCDEFGHIJKLMNO PQORSTUVWXYZ abcdefghijkimno parstuvwxyz C d st otiAc ELTOGILTE SDUTt x 8 i kali te z sx SRETTAAESAInd22 Ciria j u d DbEOHII eielelf on RBONAMSSR UFOyVt a Sr E MTP 1530II User Manual Revision 20120510 Page 80 Telpar MTP 1530II Receipt Thermal Printer User Manual PC858 Euro Character Set n 19 20 30 40 90 60 70 80 90 AU BO CO DO EO FO MTP 1500 CHARACTER SET PC858 Euro ESC t 13hex 0123456789ABCDEF RADA O123456789 lt gt ABCDEFGHIJKLMNO PQRSTUVWXYZ 7 _ abcdefghijkimno parstuvwxyz C ad
42. V graphics registered should be within 50 to shorten the execution time of this function The execution time is 60 seconds or less when the number of items registered is within 50 The execution time for 100 items is 120 seconds or less e The data value k control information data value 24 bytes area of the NV graphics data domain is used when this function is executed e NV graphics and NV bit image FS q cannot be defined simultaneously When this function is executed all NV bit images are deleted lt Function 69 gt GS L pL pH m fn kc1 kc2 x y fn 69 1D 28 4C pL pH m fn kc1 kc2 x y Description Prints the NV graphics data defined by key codes kc1 and kc2 Range e pL pH X 256 6 pL 6 pH 0 e m 48 e fn 69 e 32 lt kc1 lt 126 e 32 lt kc2 lt 126 e x 1 2 e y 1 2 X y Vertical direction Horizontal direction 1 203 dpi 203 dpi 2 101 dpi 101 dpi lt Function 112 gt GS L pL pH m fn a bx by c xL xH yL yH d1 dk fn 112 1D 28 4C pL pH m fn a bx by c xL xH yL yH d1 dk Description Stores the graphics data raster format in the print buffer b specifies the number of the color of the defined data e xL xH specify the number of dots in the horizontal direction as xL xH X 256 e yL yH specify the number of dots in the vertical direction as yL yH X 256 e c specifies the color of the defined data color 49 e d specifies the defined dat
43. a raster format Range e ForGS L 11 lt pL pH X 256 lt 65535 0 lt pL lt 255 0 lt pH lt 255 For GS 8 L 11 lt p1 p2 X 256 p3 X 65 536 p4 X 16 777 216 lt 4 294 967 295 O lt p1 lt 255 0 lt p2 lt 255 0 lt p3 lt 255 O lt p4 lt 255 m 48 fn 112 a 48 bx 1 2 enlarges graphics data in the horizontal direction 1 203dpi 2 101 dpi by 1 2 enlarges graphics data in the vertical direction 1 203dpi 2 101 dpi c 49 1 lt xL XH X 256 lt 2047 0 lt xL lt 255 0 lt xH lt 7 1 lt yL yH X 256 lt 1662 0 lt yL lt 255 0 lt yH lt 6 when by 1 1 lt yL yH A 256 lt 831 0 lt yL lt 255 O lt yH lt 3 when by 2 MTP 1530ll User Manual Revision 20120510 Page 52 Telpar MTP 1530II Receipt Thermal Printer User Manual O lt d lt 255 k int xL xH X 256 7 8 X yL yH X 256 XL xH specify the number of dots in the horizontal direction as xL xH X 256 yL yH specify the number of dots in the vertical direction as yL yH X 256 EXAMPLE XL xH X 256 64 lt XL xH X 256 X 8 dots 512 gt Eee 62 63 D A 65 66 67 126 127 128 ds l L SE k ki ki O O O O 7161514 3 2 In MSB LSB MTP 1530II User Manual Revision 20120510 Page 53 Telpar MTP 1530II Receipt Thermal Printer User Manual 4 5 5 Status Commands Three commands pertain to status trans
44. agram below shows the connector pin out of the male D Sub connector located on the printer 6 DSR High space OK for the printer to transmit data when requested The state of DSR is IGNORED for XON XOF handshaking if selected Dip Switch SW2 position 7 ON reconnects this signal to be a hardware RESET input signal normal connection to the DIR line from a computer will hold the printer always reset MTP 1530II User Manual Revision 20120510 Page 59 Telpar MTP 1530II Receipt Thermal Printer User Manual MTP 1530II User Manual Revision 20120510 Printer Side Signal Path for a cable Host Side Printer Pin on D Sub signa Sigal Peer ame Name D Sub Connector 1 NC DCD 1 2 RxD Re ES RxD 2 3 TxD TxD 3 4 DTR DTR 4 5 Ground EXA Ground 5 6 DSR lt DSR 6 7 RTS ee RTS 7 8 CTS lt CTS 8 9 NC RI 9 4 6 3 Flow Control MEMORY switch 1 position 3 ON sets the BUSY condition when the receive buffer is full OFF sets the BUSY condition when the receive buffer is full or when Off Line The MTP 1530Il employs a 4 K byte data buffer to allow the host computer to rapidly transfer data Under some circumstances it may be possible to completely fill the buffer When the Receive Buffer is within 128 bytes of being full the MTP 1530II signals the host computer to pause until the receive buffer has room 256
45. ator Instructions 2 1 Unpacking and Inspection Carefully unpack and inspect your MTP 1530II for any damage that may have occurred in transit Should any damage have occurred notify Telpar save the shipping carton and packing materials and file a damage claim with the carrier Specify the nature and the extent of the damage Before installing or operating the printer check the following e Printer mechanism and paper path are clear of all packing materials or other foreign matter e Paper is installed DO NOT OPERATE the printer without paper Refer to Section 2 2 Paper Loading page 15 for paper loading instructions 2 2 Paper Loading 2 2 1 2 2 2 Side Loading Roll The MTP 1530I series printer is configured as a side loading printer Slide roll of paper over spindle with paper fed under the bottom toward paper slot front of unit To load paper turn on the power and feed the straight edge of the paper into the paper guide AUTOLOAD will automatic load paper once it is fed into the paper guide Once paper has been initially loaded the paper feed button may be used Ensure that the paper is installed correctly and feeding properly with the thermal side facing up Black Mark Sensors Load The MTP 1530II series printer may be used with the optional Black Mark sensor This requires the use of a pre printed Top of Form TOF Mark or Black Mark on the form Dip switch SW1 position 1 must be set to the ON position to enable b
46. ble high becomes double wide Not Page mode See ESC and ESC Set relative ESCN n m 1B5Cn Set printing to current print position print position m n m 256 Ignored if specified setting exceeds the printable area See Page mode Select ESC a n 1B61n n 0 0 or 30 hex Left justify n 1 01 justification or 31 hex Center justify n 2 02 or 32 hex Right justify Normal mode only must be received at the start of a line See HT ESC and ESC Select paper ESC c 3 n 1B 63 33 Bit 1 enables or disables the paper low sensors to n sensor Bit 3 enables or disables the output paper paper out sensor A value of 1 enables end status and a value of 0 disables Applies to the parallel interface ONLY Select paper ESC c 4 n 1B 63 34 Setting bit 0 or bit 1 high causes the sensor to n Paper Low sensor to be used as a stop printing Paper Out sensor Panel ESC c 5 n 1B 63 35 LSB 0 Paper feed button is enabled buttons n LSB 1 Paper feed button is disabled enable disab During a macro instruction standby the le feed button is always enabled but will not feed paper Forward line ESC d n 1B 64 n Print if needed then feed paper n feed for n character lines Range 0 to 255dec character Maximum amount of paper fed 1016 lines mm 40 Can feed past marks in BM J ll Q A oqe od e H Select ESC t n 1B 74 n See section 6 2 Character Sets Character code table
47. can be specified is 1024 128 bytes times 8 bits per byte Any data specified and received which exceeds the printing width of the printer is read in and then discarded In standard mode this command is effective only when there is no data in the print buffer The starting point of the printed image can be set by the HT Horizontal Tab ESC Set absolute print position ESC Set relative print position or GS L Set left margin command if that position is a multiple of 8 This command is not affected by print modes character size emphasized print double strike inverted print underline reverse video etc ESC a Select justification is effective on raster bit images If the width of the printing area set by GS L and GS W is less than the minimum width the printing area is extended to the minimum width only on the line in question This minimum width is 1 dot in normal or double high mode and is 2 in double wide or quadruple mode Each data byte represents 8 horizontal dots to be printed with the MSB being to the left and the LSB being to the right For each of the 8 bits MTP 1530II User Manual Revision 20120510 Page 48 Telpar MTP 1530II Receipt Thermal Printer User Manual within each data byte a 1 represents a dot position to be printed and a 0 represents a dot position not to be printed The first x1 x2 256 data bytes are printed as the first raster line The next x1 x2 256 data bytes are printed as the s
48. de is not supported n 3 03 or 33 hex causes Firmware Version to be transmitted GS a n 1D 61 n MTP 1530II User Manual Revision 20120510 Page 54 Telpar MTP 1530II Receipt Thermal Printer User Manual 4 5 6 Enable Disable Auto Status Back ASB mode Causes the printer to transmit four status bytes on the XD line when this command is processed out of the receive buffer and also sets the conditions which will cause the printer to automatically transmit the status bytes lf all conditions are disabled then the ASB function is also disabled The status bytes are transmitted without checking to see if the host is ready to receive the data n is defined as Enable Disable Auto Status Back ASB mode Bit Function Bit 7 Not used Bit 6 Not used Bit 5 Not used Bit 4 Not used Bit 3 1 enable ASB for paper out status Bit 2 1 enable ASB for an error condition Bit 1 1 enable ASB for Online Offline Bit 0 Not used set to O Enable Disable Auto Status Back ASB mode See section 0 Status Bytes Transmitted 4 5 7 Status Bytes Transmitted First Status Byte Transmitted The first byte sent due to Status byte sent when DLE EOT Olhex ASB status printer Is received information Bit7 Not used always OFF Not used always OFF Bit6 1 PAPER FEED button Not used Bit5 1 Platen is open
49. e NV graphics area number of bytes in the NV graphics area Range e pL pHX256 2 pL 2 pH 0 e m 48 e fn 0 48 lt Function 50 gt GS L pL pH m fn fn 2 50 1D 28 4C pL pH m fn Description Prints the graphics data stored in the print buffer by using GS L lt Function 112 gt Range e pL pH X 256 2 pL 2 pH 0 e m 48 e fn 2 50 lt Function 51 gt GS L pL pH m fn fn 3 51 1D 28 4C pL pH m fn Description Transmit the number of bytes of remaining memory unused area in the NV graphics area Range e pL pHX256 2 pL 2 pH 0 e m 48 e fn 3 51 lt Function 64 gt GS L pL pH m fn d1 d2 fn 64 1D 28 4C pL pH m fn di d2 Description Transmits the key code list for defined NV graphics Range e pL pH X 256 2 pL 4 pH 0 e m 48 e fn 64 e d1i 75 e d2 67 MTP 1530II User Manual Revision 20120510 Page 50 Telpar MTP 1530II Receipt Thermal Printer User Manual lt Function 65 gt GS L pL pH m fn d1 d2 d3 fn 65 1D 28 4C pL pH m fn di d2 d3 Description Deletes all NV graphics data Range e pL pH X 256 2 pL 5 pH 0 m 48 fn 65 d1 67 d2 76 d3 82 lt Function 66 gt GS L pL pH m fn kc1 kc2 fn 66 1D 28 4C pL pH m fn kc1 kc2 Description Deletes the NV graphics data defined by key codes kc1 and kc2 Range e pL pHX256 2 pL 4 pH 0 m 48 fn 66 32 lt kc1 lt 126 32 lt kc2 lt 126 lt Function 67 gt GS
50. e adjusted to print as much of the graphics data as possible The right margin is extended first and then if the data still will not fit then the left margin is readjusted up to the point where the full width of the print head is used for printing the graphics image When 8 dot bit image is selected each byte of data represents 8 vertical dots to be printed The MSB is the top dot to be printed and the LSB is the bottom dot to be printed For each of the 8 bits within each data byte a 1 represents a dot position to be printed and a 0 represents a dot position not to be printed When 24 dot bit image is selected each series of three bytes of data represent 24 vertical dots to be printed The first byte represents the top 8 dots to be printed the second byte represents the 8 dots to be printed in the middle and the trird byte represents the bottom 8 dots to be printed The MSB of each byte is the top dot to be printed and the LSB is the bottom dot to be printed For each of the 24 bits within each series of three data bytes a 1 represents a dot position to be printed and a 0 represents a dot position not to be printed After printing a bit image the printer returns to normal mode The graphics mode is not affected by print modes emphasized double strike underline character size or reverse video but is affected by the inverted print mode MTP 1530Il User Manual Revision 20120510 Page 47 Telpar MTP 1530II Rece
51. ead as a result of printing with thermal paper not specified or approved by Telpar MTP 1530II User Manual Rev 20120510 Page 12 Telpar MTP 1530II Receipt Thermal Printer User Manual 1 7 Sensor Locations and Functions The MTP 1530II has six sensors that detect various changes in conditions relating to printer operation which may alter the course of action the printer will take depending upon the change detected The six sensors are listed described and shown below in this section 1 Print head Temperature Sensor A thermistor sensor detects the temperature of the printhead The printer stops printing operation if the print head Temperature is 75 G 167 F or higher The printer resumes normal operation after the print head cools off to 70 C 158 F or lower No photo is available for this sensor 2 Paper Present Sensor also know as the Paper End Sensor This sensor detects whether or not paper has been loaded into the printer It triggers the automatic paper feeding operation when paper is initially fed into the printer mechanism It also detects when paper has run out at which time the printer stops all printing operations until additional paper has been successfully fed into the printer 3 Platen Open Sensor A small micro switch detects whether or not the printers platen long rubber roll has been lowered away from the print head mechanism as shown in the photo below Printing operation will not be allowed while this sensor
52. econd raster line This sequence continues until all y1 y2 256 dot lines defined have been printed After printing the raster bit image the printer returns to normal mode 4 5 4 Set and Process Graphics Data GS L pL pH m fn parameter 1D 28 4C pL pH m fn parameters GS 8 L pl p2 p3 p4 m fn parameter 1D 38 4C p1 p2 p3 p4 m fn parameters In the description below only the GS L command is used for explanation Please note that GS L and GS 8 L have the same function however if the parameters in the Format column in the table below exceed 65 533 bytes then the GS 8 L command must be used Command Parameters Structure Maximum Value GS L pL pH 2 bytes 65 535 GS 8 L P1 p2 p3 p4 4 bytes 4 294 967 295 Definitions e DL and pH specify pL pH X 256 as the number of bytes after pH m fn and parameters fn specifies the function parameters specify the process of each function fn Format Gren Function Name O 0 48 GS L pL pH m fn 48 Transmit the NV graphics memory capacity 2 50 GS L pL pH m fn 50 Print graphics data in the print buffer 3 51 GS L pL pH m fn 51 Transmit the remaining capacity of the NV graphics memory 64 GS LpL pH m fn d1 d2 64 Transmit the key code list for defined NV graphics 65 GS LpLpHmfndid2d3 65 Delete all NV graphics data 66 GS L pL pH m fn kc1 kc2 66 Delete the specified NV graphics
53. ect cancel user defined Seldom Setting Yes Yes __ character set __ _ ESC amp Define user defined Seldom Setting Yes Yes characters III ESC Select bit image mode General Execute Yes Yes ESC Turn underline on off General Setting Yes Yes ESC 2 Select default line spacing General Setting Yes Yes ESC3 Set line spacing General Setting Yes Yes ESC Cancel user defined Seldom Setting Yes Yes Characters _ ESC Initialize printer General Execute Yes Yes Pt Setting gt LESCH Set horizontal tabs General Setting Ves Yes ESC E_ Turn emphasized on off___ General Setting Yes Yes ESC G Turn double strike on off General Setting Yes Yes ESC J_ Print and feed paper General Execute_ Yes Yes ESC L Select PAGE MODE PAGE Execute Start line Ignore d ESC M_ Select character font General Setting Yes Yes ESCR Select international General Setting Yes Yes __ character set _______ ____l__ ESC S Select standard mode PAGE _______ Execute Ignored Yes ESC T Select print direction______ PAGE Setting Value ie ESC V_ Turn rotated print on off General Setting Yes Value ESC W_ Set printing area PAGE Setting Value Yes ESC Set relative print position General PAGE Execute_ Yes Yes ESC a
54. ed e Items to obtain IP address subnet mask gateway address e Number of DHCP Discover retry retries 4 times e DHCP Discover retry intervals First try 4 seconds after receiving the order for IP address obtainment Second try 7 seconds from the first try Third try 15 seconds from the first try Fourth try 32 seconds from the first try e Number of DHCP request retries 10 times DHCP Request retry interval 15 seconds MTP 1530II User Manual Revision 20120510 Page 65 Telpar MTP 1530II Receipt Thermal Printer User Manual IP Address obtainment with APIPA e tems to obtain IP address e P address range 169 254 1 0 to 169 254 254 255 If the DHCP client is unable to find the information it uses APIPA to automatically configure itself with an IP address from above range If an IP address is assigned by APIPA it is not possible to communicate through a router Manual Setting The BA T500I1 operates in accordance with the IP address in the internal parameter settings reference the table on the next page MTP 1530II User Manual Revision 20120510 Page 66 Telpar MTP 1530II Receipt Thermal Printer User Manual Internal Ethernet Parameter Settings Articles Parameters Initial Values Utility Browser Status Sheet Ref Setting Ref Setting printing IP Address 192 168 192 168 Yes Yes Yes Yes Yes Subnet Mask 255 255 255 0 Yes Yes Yes Ye
55. ed to Telpar by the manufacturer s of the Product THE FOREGOING IS A LIMITED WARRANTY AND IT IS THE ONLY WARRANTY PROVIDED BY TELPAR TELPAR DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ALL WARRANTIES OR INDEMNITIES FOR PATENT OR COPYRIGHT INFRINGEMENT IN NO EVENT SHALL TELPAR BE LIABLE FOR ANY INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSS OF PROFITS REVENUE DATA OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY WHETHER IN AN ACTION IN CONTRACT OR TORT ARISING OUT OF OR RELATED TO THIS AGREEMENT EVEN IF TELPAR OR ANY OTHER PERSONS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES TELPAR S LIABILITY FOR DAMAGES HEREUNDER FOR ANY CAUSE WHATSOEVER SHALL IN NO EVENT EXCEED THE AMOUNTS RECEIVED BY TELPAR FROM THE CUSTOMER FOR THE PRODUCTS TELPAR SHALL NOT BE RESPONSIBLE FOR ANY LOSS DAMAGE OR EXPENSE OF ANY KIND CAUSED DIRECTLY OR INDIRECTLY BY THE USE OR PERFORMANCE OF THE PRODUCT PROVIDED HEREUNDER Upon inspection Telpar will make necessary repairs or replacement and return the merchandise shipping prepaid MTP 1530Il User Manual Rev 20120510 Page ii Telpar MTP 1530II Receipt Thermal Printer User Manual Table of Contents NR e CV al PPC ono ishka asua sikisauqa qusay ss 6 LL DONT Uu CET 7 1 1 1 Standard Mode versus Page Mode 7 Liz HO HEIEREN ege al i 1 1 3 Explanation of Terms used throughout this manual 9 1
56. er does not perform as expected In hex dump mode the printer prints the hexadecimal code for each character received rather than processing the data as printable text and as control commands The exception is that DLE EOT real time STATUS request and DLE ENQ Real time request to printer are executed as received even in hex dump mode The hexadecimal notation is printed at 10 characters per line on the left side of the page and the printable characters when possible are printed on the right side of the page Control codes print as periods on the right side section of the printout to help locate specific areas of the message to see what codes were actually received by the printer After all data has been sent to the printer pressing the paper feed button will flush the buffer and print the last line of data received Hex dump mode is initiated in any of three ways 1 Open the platen hold the paper feed button down turn on power then close the platen and release the paper feed button 2 Set DIP switch DPSW2 position 5 ON and then turn on power MTP 1530II User Manual Rev 20120510 Page 7 Telpar MTP 1530II Receipt Thermal Printer User Manual 3 Send the appropriate GS A command On entering hex dump mode the printer prints a 4 line header Hexadecimal Dump a blank line To terminate hexadecimal dump press FEED three times Hex dump mode is terminated by 1 pressing the paper feed button three times in quick
57. er is ready for operation OFF means power in not stable LED 2 is a PAPER OUT LED OFF means paper is installed and the printer is ready for operation ON means there is no paper Installed in the printer mechanism or the paper low sensor if selected The PAPER OUT LED blinks steadily to specify that self test has finished the first part of printing and that the user can press the PAPER FEED button to print the barber pole character print part of the self test The PAPER OUT LED also blinks steadily to specify that a MACRO is waiting for the user to press the PAPER FEED button to continue it s execution macro stand by mode LED 3 is an ERROR LED OFF means there are no errors and the printer is ready for operation ON indicates the printer is OFF LINE except during paper feeding using the FEED button during self test printing and in the error state The ERROR LED blinks a defined pattern every 5 12 seconds to notify the user of various error conditions When the LED is normally OFF and blinks ON an error is indicated which may be recoverable When the LED is normally ON and blinks OFF an error is indicated which in not recoverable For any error that is not recoverable power should be turned off as soon as possible MTP 1530II User Manual Revision 20120510 Page 26 Telpar MTP 1530II Receipt Thermal Printer User Manual ERROR LED Blink Rate and Recovery Method Table below Bl
58. est of the ESC sequence is ignored and all information starting with n1 is treated as normal data In single density mode m 00 or 20 for each bit of data received the printer prints two dots horizontally so the horizontal resolution is 101 6 dpi MTP 1530II User Manual Revision 20120510 Page 46 Telpar MTP 1530II Receipt Thermal Printer User Manual In double density mode m 01 or 21 for each bit of data received the printer prints one dot horizontally so the horizontal resolution is 203 2 dpi In 8 dot mode m 00 or 01 for each data bit received the printer prints three dots vertically so the vertical resolution is 67 7 dpi In 24 dot mode m 20 or 21 for each data bit received the printer prints one dot vertically so the vertical resolution is 203 2 dpi n1 and n2 define the number of dots per line to be printed in the horizontal direction n1 and n2 cannot both have a value of 0 The range of n1 0 to 255 dec and the range of n2 is 0 to 3 dec so a total number of horizontal dot position which can be printed with one ESC sequence can vary from 1 to 1023 If n1 or n2 is outside this range the ESC sequence is ignored and all data following is treated as normal data If the bit image data specified is more than what will fit on a line the excess data is ignored lf the width of the printing area set by GS L and GS W is less than the width required by the data sent with the ESC command the margins are r
59. evision 20120510 Page 57 Telpar MTP 1530II Receipt Thermal Printer User Manual The special characters are SHIFT and the FUNCTION characters SHIFT S FNC1 1 FNC2 2 FNC3 3 and FNC4 4 To specify the character send The usage of FUNCTION characters depends on the application program 3 In code set A the character just after SHIFT is processed as a character for code set B In code set the character just after SHIFT is processed as a character for code set C In code set C the SHIFT is invalid 4 HRI characters are not printed for the SHIFT characters or CODE SET selection characters 5 HRI for a Function character is a space 6 HRI for a control code OOhex through 1Fhex and 7Fhex is a space 7 Errors in the data cause the bar code processing to abort data following is treated as normal data a The top of the data field is not a code set selection character b Ifa sequence n is invalid c Characters that can not be used in special code set Notes in standard Mode 1 If any invalid data is received the printer only feeds paper and the following data is treated as normal data 2 If the horizontal size exceeds the printing area the printer only feeds paper 3 This command only feeds enough paper to print the bar code regardless of ESC 2 and ESC 3 settings 4 This command is valid only when there is no data in the print buffer When there is data in the print buffer the data following m
60. h ESC t Odhex 0123456789ABCDEF PEA LAA 0123456789 lt gt 2 OABCDEFGHIJKLMNO PORSTUVWXYZ _ abcdefghijklmno parstuvwxyz 7 C a fc e eit AS EFEGETOUROGUCEUOCT LUN eee ta ee 5 b ett eh eg As Hep tt ee ttt rial 1 aBrrni our 0L5ogen EDIT MER GUTT MTP 1530II User Manual Revision 20120510 Page 76 Telpar MTP 1530II Receipt Thermal Printer User Manual PC865 Nordic Character Set n 5 20 30 40 50 60 70 80 90 AO BO CO DO EU FO MTP 1500 CHARACTER SET PC865 Nordic ESC t O5hex 0123456789ABCDEF IRESE LIE 0123456789 184559 ABCDEFGHIJKLMNO PQRSTUVWXYZ 7 _ abcdefghijkimno parstuvwxyz l Cu e ddaace eeyrtiaad Esf bououyolesOohj Eee lida daadidadt44 bt t te ee tae d Hert eee ttt rial iF aBFriaoutTooONbogeh EENEG MTP 1530II User Manual Revision 20120510 Page 77 Telpar MTP 1530II Receipt Thermal Printer User Manual WPC 1252 Character Set n 16 20 30 40 50 60 70 80 90 AU BO CO DO EO FO MTP 1500 CHARACTER SET WPC1252 ESC t 10hex 0123456789ABCDEF 1 X amp 0123458171B8 1 seed ABCDEFGHIJKLMNO PORSTDY KYIINI abcdefghijkimno parstuvwxyz amp fasti eo lt Ee MES EN i u B n RB See A EE AA AAAAACEEEETf11 DNOOGOOOxXGQ UO YPE dad de e ifiti d m r A ens 2 DS AN Ae MTP 1530II User Manual Revision 20120510 Page 78 Telpar M
61. he platen is closed platen open AND printer does not feed or cut If Black Mark Sensor disabled the paper Auto load of paper AND After auto loading the paper If Black Mark Sensor disabled the printer does not cut the paper ON Disable error signal output OFF 0 2 OFF Enable error signal output ON Speed has priority over power consumption OFF 0 3 OFF Power consumption has priority over speed ON Disable auto eject when a paper out is detected OFF 0 4 OFF Enable auto eject when a paper out is detected ON RESERVED OFF 0 5 OFF ON Enable if using thick type paper paper which has excellent keeping OFF 0 6 quality OFF Enable if using normal paper ON Detect near end of paper roll by using the Black Mark sensor OFF 0 7 OFF Detect near end of paper roll by using the Near End sensor ON Disable selection of the operation by GS FF OFF 0 8 OFF Enable selection of the operation by GS FF MTP 1530II User Manual Revision 20120510 Page 24 Telpar MTP 1530II Receipt Thermal Printer User Manual Memory Switch 8 Position State Function Default Both Non divided energization mode land2 OFF Both 1 ON Two part energization mode OFF 0 2 OFF 1 ONor Four part energization mode OFF 2 0N ON Enable backwards paper feeding OFF 0 3 OFF Disable backwards paper feeding ON Autocutter is NOT installed O
62. ingual PC860 Portuguese PC863 Canadian French PC865 Nordic WPC1252 PC866 Cyrillic2 PC852 Latin2 PC858 Euro Space page International character set Control Boards have the following U S A France Germany England Denmark 2 choices Sweden Italy Spain 2 choices Japan Norway Latin America Korea Barcode embedded symbologies UPC A UPC E JAN EAN 13 JAN EAN 8 3 of 9 ITF CODABAR Code93 and Code128 Ladder Bar codes can be printed when using Page Mode Bit image mode Reverse video mode Underline printing Continuous roll paper Page Mode Two character font sizes Each can be printed from 1 to 8 times normal width and or 1 to 8 times normal height Smoothing command see GS b applies only in Page mode Black Mark sensing ESC POS is a registered trademark of SEIKO EPSON Corp MTP 1530Il User Manual Rev 20120510 Page 10 Telpar MTP 1530II Receipt Thermal Printer User Manual 1 4 Specifications e Resolution 8 dots mm 203 dots in e Paper thickness 0 056 um to 0 15 um maximum 0 0022 in to 0 0059 in e Operating temperature 20 C to 70 C 4 F to 158 F e Operating humidity 10 80 RH non condensing 34 C 93 2 F is assumed at 80 e Peak current for head drive is 6 7A at the moment that all dots are energized e Weight Approx 3 6lbs 1 6Kg e Expected life of mechanism 15 million lines e Expected life of cutter 1 million cuts 1 5 Power Supply Requireme
63. ink Rate Error Description Recovery method Continuous Print head Print head Automatic when the print head no pauses Temperature Temperature is cools off to 70 C 158 F or too high error 75 167 F or lower higher 1 blink ON then a paused OFF Cutter error The cutter has Recovers by DLE ENQ1 or DLE condition before the cycle starts failed to complete ENQ2 after the cutter Jam has again each cycle is approx 5 a cut been corrected seconds long 1 blink OFF then a paused ON PCB The printer NOT RECOVERABLE Turn condition before the cycle starts connection mechanism is not power off and check again each cycle is approx 5 error connected or the connections between the printer seconds long internal wiring is mechanism and the controller incorrect board 2 blinks ON then a paused OFF Black Mark No Black Mark was Recovers by DLE ENQ1 or DLE condition followed by another blink sensor detected even ENQ2 when the paper with the ON and a shorter paused OFF detection though the roll of black mark is inserted correctly before the cycle starts again each amor paper may be again cycle is approx 5 seconds long marked correctly 1 blink OFF then a paused ON Read Write The CPU has NOT RECOVERABLE Cycle condition followed by another blink error detected a memory power off and on to see if the OFF before the cycle starts again Read Write error error goes away each cycle is approx 5 seconds long 2 blinks OFF then a paused
64. ipt Thermal Printer User Manual 4 5 3 Set Raster Bit Image Mode NOTE Commands GS v0 FS p and FS q pertaining to raster graphics are now defined as obsolete commands in the ESC POS command system This printer supports both upward compatible commands and obsolete commands However the upward compatible commands are recommended to use because the obsolete commands will not be supported in future products Please use the supported GS L and GS 8 L commands instead to perform graphics instead described in Section 4 4 4 GS v 0 m x1 x2 y1 y2 d1 dk 1D 76 30 m x1 x2 y1 y2 data Specifies and prints RASTER bit image graphics Set Raster Bit Image Mode m Mode Vertical dot Horizontal density dot density 0 00 or 30 hex Normal 203 2 dpi 203 2 dpi 1 01 or 31 hex Double Wide 203 2 dpi 101 6 dpi 2 01 or 32 hex Double high 101 6 dpi 203 2 dpi 3 03 or 33 hex Quadruple 203 2 dpi 203 2 dpi Table 2 Set Raster Bit Image Mode The number of data bytes which must be sent to complete this command x1 x2 256 y1 y2 256 If m is not one of the specified values the rest of the ESC sequence is ignored and all information starting with n1 is treated as normal data The values of x1 and x2 select the number of data bytes x1 x2 256 in the horizontal direction The value of x1 can be from 1 to 128 and the value of x2 must be OOhex so the maximum number of dots which
65. is treated as normal data 5 This command is not affected by print modes emphasized double strike underline character size reverse video or rotated print but is affected by the inverted print mode Notes in Page mode 1 This command develops the bar code data in the print buffer The print position moves to the right side dot of the bar code 2 If any invalid data is received the printer stops command processing and the following data is treated as normal data The data buffer position does not change 3 If the bar code width exceeds the printing area the bar code is not printed but the data buffer position moves to the left side of the printing area MTP 1530II User Manual Revision 20120510 Page 58 Telpar MTP 1530II Receipt Thermal Printer User Manual 4 6 Serial RS232C Interface 4 6 1 Serial RS232C Interface Specification __ Serial RS232C Interface Specification Item Specification Data receive 115200 38400 19200 9600 4800 bps set by DIP switch speed Synchronizing Asynchronous Full duplex method Hand shake CTS RTS DTR DSR signal or XON XOFF set by DIP switch Input output RS232C Signal level Space logic 0 3 V 15 V Data Bit 8 Data bits fixed Stop Bits Fixed to 1 on the printer side Connector on Male D Sub 9 Pin See Connector pin out below Printer 4 6 2 Serial UO Connector on the Serial RS 232 Printer Option see di
66. ith the starting position set to the top right corner or the bottom left corner In Page mode with the starting this is a vertical position See ESC V 4 4 5 Top of Form Commands Name Command Command ASCII n data byte hex Form feed FF OC Feed to GS FF 1D OC Black Mark Top of Form Commands Mark Sensors Load 4 4 6 Page Mode Commands Name Command Command ASCII n data byte hex Form feed FF 0C CAN CAN 18 Print data in ESC FF 1B 0C Page mode Set absolute ESC n m 1B 24 n m print position ESC L 1B 4C mode Select Page line Settings of ESC SP ESC 2 ESC 3 have independent values in page mode and standard mode ESC V ESC a ESC GS L and GS W while in page mode makes the settings for standard mode but have no affect while in page mode The printer returns to standard mode at power on reset or ESC received See FF CAN ESC FF ESC S ESC Must be received at the start of a T ESC W GS GS1 MTP 1530ll User Manual Revision 20120510 Telpar MTP 1530II Receipt Thermal Printer User Manual standard mode cleared The printing area set by ESC W is initialized Settings of ESC SP ESC 2 ESC 3 are switched to the standard mode values See FF Data buffered in page mode is ESC FF ESC L Select print direction ESC T n 1B 54 n buffered within the printing area set by ESC W n 0 either 00 hex or 30 hex sets the starting position to the upper left corner and printing goes from
67. lable following a buffer full condition when the printer switches from Off Line to On Line or when the printer recovers from an error using DLE ENQ 1 or DLE ENQ 2 The printer sends XOF when the receive buffer becomes full or when the printer switches from On Line to Off Line MTP 1530II User Manual Revision 20120510 Page 61 Telpar MTP 1530II Receipt Thermal Printer User Manual 4 7 Centronics Parallel IEEE 1284 Interface 4 7 1 Parallel UO Connector Pin 1 Pin 18 upper right corner upper left corner Pin 19 Pin 36 lower right corner lower left corner 11 BUSY PtrBusy O High level when printer cannot Al accept data 12 PE AckDataReq O High level when printer is out of aper 13 _ SLCT Xflag o 14 AFXT_ HostBusy E ETS ND 16 GND GND Logic ground 19 GND GND Logic ground thru 31 LN ANT i 32 ERRO DataAvail O R 33 GND No de Es ND kb T 135 5 ND O MTP 1530ll User Manual Revision 20120510 Page 62 Telpar MTP 1530II Receipt Thermal Printer User Manual 4 8 USB 2 0 Interface General specifications D Li Loi D D D D D D D Complies with USB 2 0 Transmission speed USB Full speed mode 12 Mbps Communication method USB bulk transfer Power USB self powered function device USB bus current consumption 0 mA All power is supplied from the BA T50011
68. lack mark operation If DIP switch DSW1 position 1 Is turned on to enable the Black Mark sensor when the printer is loaded with plain paper at Power On the printer will feed about 17 5 inches of paper looking for a Black Mark and then go to an error mode since it did not find a Black Mark To load paper turn on the power and feed the straight edge of the paper into the paper guide Ensure that the paper is installed correctly and feeding properly with the thermal side facing up lf using perforated paper the perforation should be fed at least 1 27 mm 0 05 in past the cut line to avoid a jam at the cutter MTP 1530Il User Manual Rev 20120510 Page 15 Telpar MTP 1530II Receipt Thermal Printer User Manual The BM is detected at the position which the top edge of the BM comes into approximately 0 02 to 0 08in 0 5 to 2 mm from the center of the BM sensor After detecting the BM the BM is not detected for approximately 0 79in 20mm a a E Cutting Position ee aap usus asas Print Starting Position A B C Paper Feeding Approx 0 8 Inch Direction 2cm Paper The Figure above shows the BM Detection Position Print Starting Position and the Cutting Position A 1 32in for straight paper path model 1 46in for curled paper path model 33 6 mm for straight paper path model 37 2 mm for curled paper path model B 0 69in for straight paper path model 0 83in for curled paper path model 17 6 mm for straight paper path
69. line does not apply while reverse video is enabled Set left GS L n m 1D4C n Setthe left margin to dot position m x margin m 256 n Must be received at the start of a line Does not apply in Pase mode See GS W Set print GS T n 1G 54 n n 0 either 00 or 30hex sets the print position to position to the start of the print line the after deleting data in the print buffer beginning of n 1 either 01 or 31hex sets the print print line position to the start of the print line after printing data in the print buffer Cut GS V m 1D56 m If m 1 either 01hex or 31hex a cut is n performed and the n byte must not be sent If m is a capital B 42hex then paper is fed for n dot lines and then a cut is performed Set Right GS W n m 1057 n Sets the print width to m x 256 n Margin m relative to the left margin Must be received at the start of a line See GS Print raster GS v 0 m 1D 76 30 Error Reference source not found bit image X1 x2 y1 m x1 x2 OBSOLETE Use y2 data y1 y2 data GS L lt Function 112 50 gt instead General Usage Print Commands MTP 1530II User Manual Revision 20120510 Page 34 Telpar MTP 1530II Receipt Thermal Printer User Manual 4 4 2 Status Commands Because some of the bits in the status responses are fixed the user can confirm the command to which the status belongs and differentiate the status responses from XON XOF as shown
70. mission DLE EOT n GS n and GS a n DLE EOT n 10 04 n Real time STATUS request Status is transmitted immediately when this command is received without verifying that the host is ready to receive data This command is executed even if the printer is off line the receive buffer is full or there is an error status with a serial interface controller With a parallel interface controller this command cannot be executed when the printer is BUSY but is executed when the printer is OFF LINE or in an error state if MEMORY switch 1 3 is on Status will be transmitted even if a valid command string is received while receiving data as part of another command sequence such a part of a bit image pattern This command must not be sent to the printer in the middle of any other multi byte command sequence or this command will be interpreted as the remaining part of the multi byte command _ Status Commands n Action 01 hex Transmit Printer status 02 hex Transmit Offline status 03 hex Transmit Error status 04 hex Transmit Paper roll status Status Commands See section 0 Status Bytes Transmitted GS n 1D 49 n Transmit printer ID n 1 01 or 31 hex causes 24hex to be transmitted n 2 02 or 32 hex causes Type ID to be transmitted Bit 2 1 BM sensor is enabled Bit 1 1 Autocutter is installed Bit O 1 two byte character code is supported Bit O 0 two byte character co
71. mmands MTP 1530II User Manual Revision 20120510 byte hex 1B 25n 1B 26 03 c1 C2 data 1B 3F n 1D 28 45 p1 p2 m data Description LSB of n 0 default selects ROM character generator LSB of n 1 selects User Defined character generator See ESC amp and ESC y specifies 3 bytes per character in the vertical direction c1 specifies the first character to be downloaded and c2 specifies the last character to be downloaded x specifies the number of dots in the horizontal direction The value of x is 12dec for FontA or 09dec for FontB FontA or FontB are selected by ESC or ESC M A download bit image GS and user defined characters ESC amp can not be defined simultaneously defining either will cancel the other The previous user defined character pattern for character n 20 hex through 7E hex in either font selected by ESC is cleared and the internal character generator is used to print the character n See ESC and ESC p1 p2 256 the number of data bytes to follow m plus 1 Function 1 enters the user defined mode m 01 hex p1 03 hex p2 00 hex d1 49 hex d2 4E hex The printer transmits 37 hex 20 hex 00 hex Function 2 ends the user defined mode m 02 hex p1 04 hex p2 00 hex d1 4F hex d2 55 hex d3 54 hex The printer performs a software reset m 2 is only effective in the user defined mode Function 3 allows setting of the memory switches m 03 hex
72. mmended usage is 10 times per day macro Start end definition Macro definition starts when this command is received during normal operation and ends when this command is received during macro definition ESC does not clear the contents of the macro definition so ESC can be included in the macro definition The contents of the macro can not exceed 2048 bytes Select head control method Execute macro n 00 hex Print speed 1 150 mm second n 10 hex Print speed 2 100 mm second n 20 hex Print speed 3 80 mm second n 30 hex Print speed 4 50 mm second When Memory switch 8 position 1 is set to divided energy the maximum speed is 120 mm second Default is speed 1 n 0 through 255 specifies the number of times to execute the macro m 0 through 255 specifies how long to wait between executions of the macro m 100 milliseconds When the LSB on o is 0 the macro executes n times at the interval of m 100 msec When the LSB on o is 1 the macro executes then after an interval of m 100 msec the Paper Out LED flashes and the printer waits for the Paper Feed button to be pressed as a signal to execute the next sequence until the macro has executed n times Seldom Used Commands MTP 1530II User Manual Revision 20120510 Page 45 Telpar MTP 1530II Receipt Thermal Printer User Manual 4 5 Descriptions of Commands 4 5 1 4 5 2 Set Print Mode ESC n n is defined as 1B 21 n
73. model 21 2 mm for curled paper path model C Approx 0 02in to 0 08in Approx 0 5 to 2mm Black Mark Print Starting Position and Cutting Position At the factory the print starting position and the cutting position are set to the print head position and the cutter position respectively when the BM sensor detects the BM The print starting position and the cutting position can be changed with the GS F command Acceptable Width and Interval of Black Mark The width and interval of BM for which the printer operation is guaranteed are as follows BM width 3 to 20 mm 0 12in to 0 79in BM interval 50 to 300 mm 1 97in to 11 81 in MTP 1530Il User Manual Rev 20120510 Page 16 Telpar MTP 1530II Receipt Thermal Printer User Manual 2 3 Paper J am In the event of a paper jam condition do not force paper into the unit or try to pry the paper out of the unit this may damage the thermal print mechanism Caution should be exercised when working next to the cutter mechanism the blades are sharp and may cause serious injury To release paper e Turn off power to the printer e Push the Head Open lever to the down position e Paper can be removed at this time Once paper is cleared from the mechanism return the Head Open lever to the up position 2 3 1 Head Open Lever The Head Open lever green is located at the left front of the printer mechanism as shown in the two pictures below The up position is ready to print The dow
74. n position lowers the platen roller away from the print head for manually inserting paper or for clearing a paper jam The down open position signals the microprocessor that the head is open so that no printing will occur Head Open Lever shown in its closed position Head Open Lever shown in its open position Placing the lever in the down position allows for jams near the platen area to be cleared or for loading paper manually MTP 1530Il User Manual Revision 20120510 Page 17 Telpar MTP 1530II Receipt Thermal Printer User Manual 3 Installation 3 1 Self Test Mode The MTP 1530Il has a self test mode that will print and cut a sample ticket To place the unit into self test mode first turn power switch off then press and hold the FEED push button switch Next place the POWER switch in the ON position to apply power to the printer Release the FEED Button after printing starts within 5 seconds See a sample of a Self Test Printout on the next page The first part of the self test message prints several fields showing how the printer is configured Following the first part of the self test you have the option of pressing the paper feed button once more to print a barber pole pattern print test of ASCII Characters or turning power off and back on to terminate the self test The printer goes to the off line BUSY state when self test starts and remains off line until self test is finished due two either of
75. nding an FF 6 After printing the printer automatically returns to standard mode Example Sample program in BASIC assumes transmission to the printer is already possible with file 1 open 100 PRINT 1 CHR 110 PRINT 1 CHR amp H1B L amp H1B W CHR 0 CHR 0 CHR 0 CHR 0 120 PRINT 41 CHR 200 CHR 0 CHR 144 CHR 1 130 PRINT 1 CHR amp H1B T CHR 0 140 PRINT 1 Page mode lesson TEST 1 150 PRINT 1 CHR amp HC E In the program a printable area of 200 X 400 dots starting at 0 0 is set and characters are printed on the first line of the area as shown in the figure below Note that a line feed was inserted between lesson and TEST 1 This line feed was inserted automatically because there was no room for the blank following the word lesson within the horizontal range of the 200 400 printable area The feed amount here is that specified by ESC 3 Any number of printable areas can be specified before the FF is executed If any printable areas overlap however the logical sum of the data written to the overlapping portions is used for the final printing Page mode lesson TEST 1 lt Paper Printable area MTP 1530ll User Manual Revision 20120510 Page 40 Telpar MTP 1530II Receipt Thermal Printer User Manual 4 4 7 NV Memory and Down Load Bit Images Commands A download bit image is stored in RAM and is cleared by a power cycle or by the commands ESC
76. nts 1 5 1 Voltage 24 VDC 10 Current Requirements Peak Current approximately 6 7 Amps Mean Current approximately 3 0 Amps Stand by 0 1 Amps Table 1 Current Requirements lf the number of dots that are energized at the same time is increased a higher current will flow therefore the user should use power supplies with a current capacity adequate for the corresponding print duty 1 5 2 Power Supply Option from Telpar Telpar Part Number 103929 0200 Telpar offers a safety agency approved 100 to 240 VAC 50 60Hz input to 24VDC output power supply suitable for most printing applications which use the MTP 1530lI Printer Please ask the Telpar Sales Team for more information MTP 1530Il User Manual Rev 20120510 Page 11 Telpar MTP 1530II Receipt Thermal Printer User Manual 1 5 3 3 Pin Hosiden Connector on Printer for Power Supply Connection As viewed from back of printer 24 Large notch NC GHD Flat Power connector Hosiden CS S6oU S53707T0 3 P in Hosiden Power Supply Connector 1 6 Telpar Roll Paper for the MTP 1530Il Printer Telpar Part Number 251103 8006 Thermal sensitive coating is on the inside of the roll 52 mm 6 in outside diameter 80 mm 3 15 in wide length 180 m 590 ft For use with the standard 44 5mm diameter 1 75 in diameter MTP 1530II printer spindles Specific to Thermal Printers Telpar does not warranty damages to the thermal print h
77. olding down the push button for three seconds or more while the printer is ready to print causes the module internal setting parameters to be printed out LED Communication Indicators The on board green LED lights when a link to the Ethernet is established while the yellow on board LED lights when the printer receives print data Basic Communications Protocols IP ARP ICMP UDP TCP Printing Communications Protocols LP and LPR transfers printing data e Name of remote printer aux e Printers simultaneously connectable 10 maximum e Number of connected printers that can print 1 other users must wait until the printing is done e Time out 5 minutes e Job deletion Not supported e Banner printing Not supported TCP Socket Port Transfers printing data and printer status with direct socket communications e Port Type TCP communications port for direct printing e Port number 9100 e Port communication direction bi directional e Time out 5 minutes Protocols for obtaining and setting status HTTP SNMP ENPC HTTP Displays module status and makes setting with the web browser e Port Number 80 e User Name Epson Default e Password no password e Printers simultaneously connectable 1 maximum e HTTP version HTTP 1 1 MTP 1530II User Manual Revision 20120510 Page 64 Telpar MTP 1530II Receipt Thermal Printer User Manual SNMP MIB Management Information Base PDU Protocol Data Unit
78. power on as described above To run a printer self test hold the FEED button down during this period MTP 1530II User Manual Revision 20120510 Page 68 Telpar MTP 1530II Receipt Thermal Printer User Manual 5 Drivers for the Printer Printer drivers for the MTP 1530II may be downloaded through the Telpar website at www telpar com under the Drivers and Support tab First select Printer Drivers from the Drivers and Support drop down list Next select the MTP 1500 Printer Drivers option Finally select the Windows Drivers for the MTP 1500 zip file and download it to your computer Note the zip file includes driver installation instructions Also it is important to note that the MTP 1530II uses the BA T500II Control board Therefore you will be installing the driver for the EPSON BA T500Il Receipt Printer in order to successfully operate your MTP 1530II printer through the driver The downloaded zip file will contain two executable files exe files a text file txt file and a pdf file e Double clicking on the pdf file contained in the downloaded zip file will open the driver installation manual e The file that starts with APD_ is the print driver installation program By double clicking this file you will start the driver installation setup program Follow the prompts and the manual instructions to properly install the printer driver e By double clicking on the file that starts with
79. r If a data value is less than the previous data value this command is terminated NUL terminates this command when less than 32 TAB positions are being set ESC D NUL clears all tab positions Default is every Ce Ol Turn ESC E n 1b 45 n LSB 0 Turn emphasized mode off emphasized LSB 1 Turn emphasized mode on See mode on off ESC Turn double ESC G n 1B 47 n LSB 0 Turn double strike mode off strike mode LSB 1 Turn double strike mode on on off Printout is the same as emphasized See ESC E MTP 1530Il User Manual Revision 20120510 Page 32 Telpar MTP 1530II Receipt Thermal Printer User Manual Name Command Command Description ASCII n data byte hex Forward ESC J n 1B 4A n Print if needed then feed paper n dot paper feed lines Range 0 to 255dec If BM is for n dot enabled this command can feed paper lines past the mark Select ESC M n 1B 4D n n 0 00 or 30 hex selects FontA character 12x24 n 1 01 or 31 hex selects font FontB 9x17 See ESC Select ESC R n 1B 52 n Select international character set See International Section Error Reference source not character found Error Reference source not set found reprint section Rotate print ESC V n 1B 56 n n 1 01 or 31 hex Rotate the print 90 degrees clockwise n 0 00 or 30 hex Cancel the rotation Rotated characters do not get underlined Double wide becomes double high and dou
80. r defined characters ESC 8 can not be defined simultaneously defining either will cancel the other downloaded bit image NV Memory Commands MTP 1530II User Manual Revision 20120510 Print the downloaded bit image defined by GS in the resolution specified by m m 0 either OOhex or 30hex 203 by 203 density m 1 either O1hex or 31hex 203 V by 102 H density m 2 either O2hex or 32hex 102 V by 203 H density m 3 either OShex or 33hex 102 V by 102 H density Must be received when the print buffer is empty Is not affected by print modes emphasized double strike underline character size reverse video rotated etc but is affected by upside down printing mode If the downloaded bit image exceeds the printable area the excess data is not printed If the margins have been set by the GS L and or GS W commands this command will readjust the margins as required to print as much of the data as possible for the printer mechanism being used In Page mode the terms horizontal and vertical depend on the print starting position defined by ESC T Page 42 Telpar MTP 1530II Receipt Thermal Printer User Manual Seldom Used Commands Command n data 4 4 8 Seldom Used Commands Name Command ASCII Set cancel ESC n user defined character set defined C1 C2 X characters data Define User ESC 8 y defined Cancel user ESC n characters User defined GS E p1 co
81. rmal Printer User Manual 4 Setup and Control of the Printer 4 1 DIP Switch Settings and Memory Switch Settings DIR Switch Settings The MTP 1530Il Parallel and Ethernet printers each have a single DIP Switch located on the main circuit board Labeled DSW1 while the Serial RS 232 printer has two DIP Switches located on the main circuit board labeled DSW1 and DSW2 The DIP Switch contains a bank of eight individual switches each of which controls some aspect of the printer and are described in the tables below The switches can slide up into the ON position or down into the OFF position A small tip screwdriver or even a pen tip may be used to change the position of the switches The DIP Switch on each type of printer can be accessed through a cutout hole on the metal circuit board cover see picture below Therefore DIP Switch changes can be made without removing the cover IMPORTANT NOTE I you make any changes to the DIP Switch settings you must first cycle power to the printer or reset the printer in order for the changes to take place DIP Switch Bank for a Parallel Printer as looking through the Chassis Note the numbering below each switch position 1 8 left to right and DSW 1 labeled on the board directly below the switch Each individual switch is turned ON by sliding it all the way to its up position Sliding a switch down turns it OFF MTP
82. s Yes Gateway Address 0 0 0 0 Yes Yes Yes Yes Yes DHCP Enable Disable Disable Yes Yes Yes Yes Yes APIPA Enable Disable Disable Yes Yes Yes Yes Yes ARP Ping Enable Disable Enable Yes Yes Yes Yes No Community name 1 Max 16 Chars public Yes No Yes No Yes read only Community name 2 Max 16 Chars None Yes Yes Yes Yes Yes read write IP Trap 1 Enable Enable Disable Disable Yes Yes Yes Yes No IP Trap 2 Enable Enable Disable Disable Yes Yes Yes Yes No Community name Max 16 Chars None Yes Yes Yes Yes No IP Trap 1 Community name Max 16 Chars None Yes Yes Yes Yes No IP Trap 2 IP Trap 1 Address None Yes Yes Yes Yes No IP Trap 2 Address None Yes Yes Yes Yes No Password None No Yes Yes No No Physical Layer Setting Auto Negotiation Auto Negotiation Yes Yes Yes Yes Yes 10Base T Half 10Base T Full 100Base TX Half 100Base TX Full Hardware Version Yes No Yes No Yes Firmware Version na Yes No Yes No Yes MAC Address q Ss Yes No Yes No Yes MTP 1530II User Manual Revision 20120510 Page 67 Telpar MTP 1530II Receipt Thermal Printer User Manual Notes pertaining to Ethernet Settings Changing internal parameter settings Internal parameter settings can be changed with the following methods e ENPC protocol e HTTP browser e arp and ping commands Only IP address is settable Setting with a dedicated utility Epson provides a dedicated utility that makes miscellaneo
83. s black marks pre printed on it and you wish to have the printer detect the presence of these black marks you must have DIP Switch 1 position 1 set to the ON or up position see section 4 1 NOTE Typically the Black Mark sensor is located on the left hand side of the printer as looking from the front see photo below Therefore this only detects the black mark on that side of the paper If the black mark is located on the other side of the paper the Black Mark sensor can be physically moved to its right hand mounting position on the opposite side of the mechanism one small screw must be removed to remove the sensor MTP 1530Il User Manual Rev 20120510 Page 13 Telpar MTP 1530II Receipt Thermal Printer User Manual Paper Present Sensor Black Mark Sensor location Alternate l right hand location shown is the bottom of mounting location for the sensor encasement the Black Mark Sensor shown is the bottom on the opposite side of of the sensor PP the mechanism Platen long black ne View of the Front of the printer mechanism with the platen in the down position Platen Open Sensor Paper Low Sensor location Photo shown with the Location platen in the open Mounted just above the down position paper roll spindle d Paper J am Sensor location hidden under platen roll MTP 1530ll User Manual Rev 20120510 Page 14 Telpar MTP 1530II Receipt Thermal Printer User Manual 2 Oper
84. set by ESC T to the upper left or lower right of the printing area then the position is in the vertical direction but if the starting position is set to the upper right or lower left of the printing area then the position is in Sets the absolute vertical starting the horizontal direction set relative vertical print Page mode position 1D 5C n m position plus n m 256 0 125 mm positive down the page or 65536 n m 256 0 125 mm negative up the page If the starting position is set by ESC T to the upper left or lower right of the printing area then Set printing position to current the offset is in the vertical direction MTP 1530II User Manual Revision 20120510 Telpar MTP 1530II Receipt Thermal Printer User Manual but if the starting position is set to the upper right or lower left of the printing area then the offset is in the horizontal direction Turn GS b n 1D 62 n LSB 0 turns smoothing off LSB smoothing 1 turns smoothing on Smoothing mode on off applies to built in or user defined characters when printed at any size larger than the normal See ESC GS Page Mode Commands Here is an example of using page mode A typical procedure for transmitting commands in page mode is as follows 1 Transmit ESC L to enter page mode 2 Specify the printable area using ESC W 3 Specify the printing direction using ESC T 4 Transmit the print data 5 Collectively print the data by se
85. t Document 901033 0214 MTP 1530Il User Manual Rev 20120510 Page 6 Telpar MTP 1530II Receipt Thermal Printer User Manual 1 1 Definitions 1 1 1 Standard Mode versus Page Mode The printer operates in two print modes standard mode and page mode In standard mode the printer prints and feeds paper each time it receives print data or paper feed commands In page mode all the received print data and paper feed commands are processed in the specified memory and the printer executes no operations All the data in the memory is then printed collectively when an ESC FF or FF command is received For example when the printer receives the data ABCDEF lt LF gt in standard mode it prints ABCDEF and feeds the paper by one line In page mode ABCDEF is written to the specified printing area in memory and the position in memory for the next print data is shifted by one line The ESC L command puts the printer into page mode and all commands received thereafter are processed in page mode Executing an ESC FF command prints the received data collectively and executing an FF command restores the printer to standard mode after the received data is printed collectively Executing an ESC S command restores the printer to standard mode without printing the received data in page mode the received data is cleared from memory instead 1 1 2 Hex Dump Mode This function is sometimes useful for diagnosis of application programs when the print
86. t used 1 an auto recoverable error has occurred print head temperature or platen open Bit 5 Not used 1 an un recoverable error has occurred Bit4 Not used always OFF Not used always ON Bit3 1 PAPER OUT 1 a cutter error has occurred Bit2 1 PAPER OUT 1 a mechanical error has occurred Bitt 1 PAPER LOW Not used always ON Bit 0 1 PAPER LOW Not used always OFF Third Status Byte Transmitted Fourth Status Byte Transmitted Fourth Status Byte Transmitted Bar Code Command GS k m d1 dn NUL The fourth byte sent due to Status byte sent when DLE EOT ASB status paper sensor 04 hex is received information Bit7 Not used always OFF Not used always OFF Bit6 Not used Bits 6 amp 5 both 1 paper out BitS Not used Bits 6 amp 5 both 1 paper out Bit4 Not used always OFF Not used always ON Bit3 Not used Bits 3 amp 2 both 1 Paper low Bit2 Not used Bits 3 amp 2 both 1 Paper low Bit 1 1 MEMORY switch 1 3 is Not used always ON ON Bit 0 Not used Not used always OFF 1D 6B m DATA 00 For m OOhex through O6hex m selects the bar code type Bar Code Commands m Bar Code No of data Valid data bytes ASCII 00 hex UPC A 110r12 0 9 01 hex UPC E 11 0r12 0 9 02 hex JAN EAN 13 12or 13 0 9 03 hex JAN EAN
87. tch for setting the printer On Line or Off Line The printer automatically goes Off Line in the following cases a During power on or reset through the I O connector until the printer is ready to receive data During self test While feeding paper with the paper feed button When out of paper When the print platen is open During a macro execution and in standby status When an error occurs oro 20 5 1 2 Applications for the MTP 1530Il Printer e Parking ticket dispensing e Automated Teller Machines ATMs e Gaming receipts e Interactive media kiosks MTP 1530Il User Manual Rev 20120510 Page 9 Telpar MTP 1530II Receipt Thermal Printer User Manual 1 3 Standard Features Direct thermal printing Interfaces Serial RS232 Parallel IEEE 1284 USB 2 0 Ethernet 10BASE T and 100BASE TX Paper widths 80 mm 3 15 in Full or Partial Document Cutter specified at time of order All metal construction Paper low sensor Paper auto load function ESC POS The commands conform to ESC POS which is a standard in the distribution industry Print Speed 250 mm s DIP switches accessible without removing cover Paper capacity 152 mm 6 in diameter roll with 50 mm diameter core Overall size including 152 mm 6 inch diameter roll of paper 169 8 mm x 150 3 mm x 243 4 mm 6 68 in H x 5 92 in W x 9 58 in D Inverted print mode Character code tables PC437 USA default Katakana PC850 Multil
88. the HRI fields a small square is printed as the start character and as the stop character before and after the HRI character string In the HRI field a small solid block followed by alphabetic character is printed when a control code is printed The character printed after the block for each control code is nn in hex alphe character 00 U 01 A 02 B 03 C 04 D 05 E 06 F 07 G 08 H 09 l 0A J 0B K 0C L 0D M OE N OF O 10 P 11 Q 12 R 13 S 14 T 15 U 16 V 17 W 18 X 19 Y 1A Z 1B A 1C B 1D C 1E D LEE ZE Te Notes when CODE128 m 49 hex is used 1 The first character of the bar code data string must be the code set selection character CodeA CodeB or CodeC which selects the first code set to use Code setcharacters are specified by sending a two character sequence the first character is 7B hex and the second is a printable ASCII character CodeA A CodeB B CodeC C a Code set A consists of the ASCII characters 00 hex through 5F hex FNC1 through FNC4 SHIFT CodeB and CodeC b Code set B consists of the ASCII characters 20 hex through 7F hex FNC1 through FNC4 SHIFT CodeA and CodeC c Code set C consists of 2 digit numeral characters using one character 100 numerals from 00 dec through 99 dec or 00 hex through 63 hex FNC1 CodeA and CodeB Special characters are specified by sending a two character sequence the first character is 7B hex and the second is a printable ASCII character MTP 1530Il User Manual R
89. ting Yes Yes GSc___ Print counter Counter Execute Yes Yes GSf Select font for HRI Bar Code Setting Yes Yes characters ________ ________ GSh__ Set bar code height Bar Code Setting Yes Yes GSk Print bar code Bar Code Execute Empty Yes MTP 1530II User Manual Revision 20120510 Page 29 Telpar MTP 1530II Receipt Thermal Printer User Manual GSr_ Transmit status Status GS v0 Print raster bit image General OBSOLETE Use instead GS L lt Function 112 50 gt Gsw _ Set bar code width Bar Code GS L Specify graphic data Graphics GS 8 L Control Codes and Control Sequences MTP 1530ll User Manual Revision 20120510 Execute Yes Yes Execute Empty Disabl ed Setting__ Yes___ Yes Setting Yes Yes and execute Page 30 Telpar MTP 1530II Receipt Thermal Printer User Manual List of Control Codes and Control Sequece Locations Control Codes Control Sequences Bar Code See 4 4 3 Bar Code Commands page 35 Counter See 4 4 4 Counter Commands page 36 General See 4 4 1 General Usage Print Commands page31 NV amp DL See 4 4 7 NV Memory and Down Load Bit Images Commands page 41 Page See 4 4 6 Page Mode Commands page 38 Seldom See 4 4 8 Seldom Used Commands page 43 Status See 4 4 2 Status Commands page 35 Top of Form See
90. uct This warranty shall not apply to any Product which has i been repaired or altered except by Telpar ii not been maintained in accordance with all of the operating or handling instructions supplied by Telpar or ill been subjected to misuse willful acts abuse tampering negligence or accident unusual physical or electrical stress as Telpar determines in its sole discretion Customer acknowledges that Telpar provides no warranty for any third party materials and Telpar is not responsible and will have no liability for any items or services provided to Customer by any person or entity other than Telpar Telpar s duty to perform under any warranty may be delayed at Telpar s sole option until Telpar has been paid in full for all Products purchased by Customer No such delay shall extend the warranty period To obtain assistance under this limited warranty Customer should contact the selling agency or write to Telpar Warranty Claims Department 187 Crosby Road Dover NH 03820 U S A Telephone 800 872 4886 or fax 603 742 9938 No person including without limitation any agent salesman dealer or distributor has the authority to act on behalf of Telpar to expand Telpar s obligation beyond the terms of this express warranty or to state that the performance of the Product is other than published by Telpar For Products not manufactured by Telpar to the extent permitted Telpar assigns to Customer the benefits of any warranties provid
91. us settings with the ENPC protocol Setting with a browser An HTTP browser can make setting when connected to the module The new IP address takes effect when the printer power is turned off and back on Setting the IP Address with arp ping This function is available only when it has been enabled The setting can be made only from a host PC that supports both arp and ping commands and is in the same segment as the module The new IP address takes effect when the BA T500I1E responds to the ping command Examplel When using Sun OS arp s 123 456 789 123 00 00 85 06 00 01 temp ping 123 456 789 123 Example2 When using Windows OS arp s 123 456 789 123 00 00 85 06 00 01 ping 123 456 789 123 How to check the Mac Address The Mac address of the BA T500I1E can be confirmed with the following methods e Printing the status sheet e Label attached to the BA T5001 E e Using HTTP browser e Printer self test Start up period To initialize the BA T500I1E and network connection there is start up period after the power of printer is turned on or reset The start up period depends on the IP address setting as follows When setting IP address manually approximately 6 seconds When setting IP address automatically approximately 13 seconds It may take some more time depending on the DHCP server response time During this period no network function works Setting the TM printer A Start up period is required after turning the printer
92. x selects the function for the position to start printing when used by FF or GS FF commands a 02 hex selects the function for the position to start cutting when used by the GS V command m 0 either 00 hex of 30 hex specifies a forward paper feed m 1 either 01 hex of 31 hex specifies a reverse paper feed n1 n2 256 0 125 mm specifies how much to feed The default of all adjustment values is 0 Save or load GS M p1 adjustment values in NV memory Function 1 saves the settings made by GS Fin NV memory n 1 either 01 hex or 31 hex m 1 either 01 hex or 31 hex p1 02 hex p2 00 hex Function 2 n 2 either 02 hex or 32 hex m 0 either 00 hex or 30 hex setting made by GS F is set as the default value or m any value except either 00 hex or 30 hex setting values are stored in area m of memory p1 02 hex p2 00 hex Must be processed at the beginning of a line No effect in page mode Function 3 set whether or not the value saved in NV memory is the MTP 1530II User Manual Revision 20120510 Telpar MTP 1530II Receipt Thermal Printer User Manual default to be used at power on n 3 either 03 hex or 33 hex m 0 either 00 hex or 30 hex the printer does not load the value from NV memory at initialization m any value except either 00 hex or 30 hex the printer loads the value from NV memory at initialization Frequent writes may damage the NV memory Maximum reco

Download Pdf Manuals

Related Search

Related Contents

AmbulAnciAs - TQ Medicine  LG 55LM6200 Energy Guide : Free Download, Borrow, and Streaming : Internet Archive      FORTECO  N－64D型外形図 Model (1)  Samsung MW81W-S/XEH Felhasználói kézikönyv  USER MANUAL  Data Sheet - Valiant Communications Limited  E-SHOP HELP  

Copyright © All rights reserved. Failed to retrieve file